ZyXEL P-870HN-5xb

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.
See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

802.11n Wireless VDSL2 4-port Gateway

PARTLY SUPPORTED (router boots up, but some drivers don't work)

The Board ID probably uses a wrong layout.

The ZyXEL P-870HW-51a is very similar to this model, but has the following differences:

  1. Wireless: BCM4318 B/G.
  2. Flash size: 4 MB.
  3. VDSL capable only.

Install OpenWrt (generic explanation)

Old firmwares:

All these versions have significant bugs:
1) switch - only two middle LAN ports (labelled 2 and 3) work
2) wireless - bcm43222 isn't recognized?
3) LED - LED state does not reflect the state of the router

At least P-870HN-51b can be flashed directly from OEM web interface.

It requires a serial console connected to the router.

  • Configure a static IP on your computer with the 192.168.254.33 address.
  • Install a TFTP server in your computer and put the bin firmware on its serving directory
  • Use this command at the CFE console:
     tftp -g -t i -f openwrt-96368MVWG-generic-squashfs-cfe.bin 192.168.254.33
P-870HN-51b P-870HN-53b
Architecture MIPS
Vendor Broadcom
bootloader cfe
System-On-Chip bcm6368_product_brief.pdf
Board ID 96368MVWG
CPU/Speed BCM4350 V3.1 / 400MHz
Flash size 8 MiB
Flash-Chip Macronix MX29LV640EBTI-70G
RAM 32 MiB 64MiB
RAM-Chip Winbond W9412G6IH-5? x2 ???
Wireless BCM43222KFBG/ 2×2 MIMO for 2,4GHz 802.11b/g/n
switch 4x FastEthernet10/100
Modem ADSL2+/VDSL2 (physical port RJ11) ADSL2+/VDSL2 (physical port RJ45)
USB Yes 2x (SoC) [NOT soldered on PCB]
Serial Yes
JTAG Seems no
FCC ID I88P870HN51B

Motherboard

P-870HN-51b:

 P-870HN-51b

P-870HN-53b:

 P-870HN-53b

More galleries: https://wikidevi.com/wiki/ZyXEL_P-870HN-51b

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

GND NC Serial connection parameters 115200, 8N1 Rx Tx VCC J2 Δ
CFE> athe
Available commands:

ATSE                show the seed of password generator
ATEN                set BootExtension Debug Flag
ATSH                dump manufacturer related data in ROM
ATER                Erase ROM-D partition
ATBR                Reset to default Romfile
ATGO                boot router
ATSR                system reboot
ATHE                print help

For more information about a command, enter 'help command-name'
*** command status = 0
CFE>
CFE> ATSH                dump manufacturer related data in ROM

ZLD      Version       : V1.10(VFS.0)b3
Bootbase Version       : V1.34 | 12/27/2011 22:37:03
Vendor Name            : Frontier Communications Corp.
Product Model          : P-870HN-51b
Serial Number          : S110Y44018146
First MAC Address      : C86C875C11A9
Last MAC Address       : C86C875C11B2
MAC Address Quantity   : 10
Default Country Code   : FF
Boot Module Debug Flag : 00
RootFS      Checksum   : 65ee40b7
Kernel      Checksum   : d71645ce
RomFile     Checksum   : eba9b27e
ImageDefaultChecksum   : 54f14a56
Main Feature Bits      : 00
Other Feature Bits     :
                5a 59 40 16 00 00 00 00-00 00 00 00 00 00 00 00
                00 00 00 00 00 00 00 00-00 00 00 00 00 00

CFE version 1.0.37-107.23 for BCM96368 (32bit,SP,BE) Build Date: 12/27/2011 (FuChia@MsgSW4-SerVer) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Checking Reset button on EXT INTR 0 Checking Reset button on EXT INTR 0 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Board Id (0-15) : 96368MVWG Number of MAC Addresses (1-32) : 10 Base MAC Address : c8:6c:87:5c:11:a9 PSI Size (1-128) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Wait for Multiboot Service Packet... 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80222300 Decompression OK! Entry at 0x80222300 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80222300 Linux version 2.6.30 (FuChia@MsgSW4-SerVer) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Jan 4 11:38:27 CST 2012 Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 96368MVWG prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 01f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00001f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00001f00 On node 0 totalpages: 7936 free_area_init_node: node 0, pgdat 80295c20, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 30 pages used for memmap Normal zone: 3810 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 28516k/31744k available (2144k kernel code, 3228k reserved, 445k data, 116k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 net_namespace: 816 bytes NET: Registered protocol family 16 Total Flash size: 8192K with 135 sectors registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff] BLOG v2.1 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM msgmni has been set to 55 io scheduler noop registered (default) PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8010100 brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8018 is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Jan 4 2012 11:12:01 Broadcom Logger v0.1 Jan 4 2012 11:11:09 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 116k freed init started: BusyBox v1.00 (2012.01.04-03:14+0000) multi-call binary BusyBox v1.00 (2012.01.04-03:14+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Packet Flow Cache Char Driver v2.1 Jul 15 2010 09:29:38 Registered<242> NBUFF v1.0 Initialized Broadcom Packet Flow Cache learning via BLOG enabled. Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Constructed Broadcom Packet Flow Cache v2.1 Jul 15 2010 09:29:37 Broadcom Packet CMF (Experimental) Char Driver v0.1 Jul 15 2010 09:29:34 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jul 15 2010 09:29:33 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 Jan 4 2012 11:11:15 ETH Init: 180 tx BDs at 0xa18d4000 ETH Init: 180 tx BDs at 0xa199c000 ETH Init: 400 rx BDs at 0xa19eb000 ETH Init: 400 rx BDs at 0xa19fb000 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 15 2010 09:29:35 Registered Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 15 2010 09:29:35 Registered Broadcom Packet CMF (Experimental) ENABLED. eth0: MAC Address: C8:6C:87:5C:11:A9 eth1: MAC Address: C8:6C:87:5C:11:A9 eth2: MAC Address: C8:6C:87:5C:11:A9 eth3: MAC Address: C8:6C:87:5C:11:A9 eth4: MAC Address: C8:6C:87:5C:11:A9 PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl:srom not detected,using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43222_map.bin wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.60.120.11.cpe4.06L02.1 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs p8021ag: p8021ag_init entry Broadcom 802.1Q VLAN Interface, v0.1 ===== Release Version 4.06L.02 (build timestamp 120104_1421) ===== Sun Jan 1 00:00:00 UTC 2012 update Persistent size = 24029, offset = 0 update BackupPsi size = 24029, offset = 0 ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1024 buckets, 4096 max) dhcpd:error:12.771:set_iface_config_defaults:621:SIOCGIFADDR failed on br0! xt_time: kernel timezone is -0000 iptables: Bad rule (does a matching rule exist in that chain?) Sntp: Using new rule EST5EDT,M3.2.0/2,M11.1.0/2 device eth0.0 entered promiscuous mode device eth0 entered promiscuous mode br0: port 1(eth0.0) entering forwarding state device eth0 is not a slave of br0 Created new Tag Rule: dev=eth0, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth0, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth0, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows device eth1.0 entered promiscuous mode device eth1 entered promiscuous mode br0: port 2(eth1.0) entering forwarding state device eth1 is not a slave of br0 Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth1, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth1, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows device eth2.0 entered promiscuous mode device eth2 entered promiscuous mode br0: port 3(eth2.0) entering forwarding state device eth2 is not a slave of br0 Created new Tag Rule: dev=eth2, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth2, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth2, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows device eth3.0 entered promiscuous mode device eth3 entered promiscuous mode br0: port 4(eth3.0) entering forwarding state device eth3 is not a slave of br0 Created new Tag Rule: dev=eth3, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth3, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth3, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows WLmngr Daemon is running optarg=0 shmId=0 BcmAdsl_Initialize=0xC00F8E2C, g_pFnNotifyCallback=0xC0128AF4 wlevt_init@107: opened loopback socket 4 wlevt is ready for new msg... Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 067, PhaseValue = -050, PhaseCntl = 0x3FBD0000 QPROC is aligned, i = 068, PhaseValue = -150, PhaseCntl = 0x3FBD7FBD Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x78 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA1FFFFF8, 0x11541401 0x572DBFEF *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xBDAC0 => 0xEB1E0 *** AdslCoreSharedMemInit: shareMemAvailable=85504 AdslCoreHwReset: pLocSbSta=80428000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA1FB3438 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa09bd000 XTM Init: 100 rx BDs at 0xa0917800 PROGRAM : VcAutoHunt main > ENTER /var/cert/acscert2.cacert: cannot open ln: /var/cert/bdbefb5f.0: File exists Broadcom Packet CMF (Experimental) ENABLED. Broadcom Packet Flow Cache learning via BLOG enabled. Broadcom Packet Flow Cache flushing the flows monitor task is initialized pid= 191 General UPnP daemon is ready to run with NATT 1 Switch MDK: num_switches = 1 Switch MDK: unit = 0; phy_pbmp = 0x1f; config_pbmp = 0x1f Switch MDK link poll thread: unit=0; phypbmp=0x1f eth4 Link UP -1 mbps half duplex update Persistent size = 24029, offset = 0 update BackupPsi size = 24029, offset = 0 update Persistent size = 23956, offset = 0 update BackupPsi size = 23956, offset = 0 There is no Predefined DevicePin in CFE WPS Device PIN = 17258227 Setting SSID: "FrontierHSI" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" version Frontier P-870HN-51b Login: admin Password: update Persistent size = 24303, offset = 0 update BackupPsi size = 24303, offset = 0 > cat /proc/cpuinfo system type : 96368MVWG processor : 0 cpu model : Broadcom4350 V3.1 BogoMIPS : 399.36 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available unaligned exceptions : 21 > > cat /proc/version Linux version 2.6.30 (FuChia@MsgSW4-SerVer) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Jan 4 11:38:27 CST 2012 > free consoled:error:333.883:processInput:507:unrecognized command free > Line 0: xDSL G.994 training cat /proc/meminfo Line 0: ADSL link down bcmxtmcfg: XTM Link Information, portid = 0, State = DOWN, Service Support = PTM Broadcom Packet CMF (Experimental) SWC FLUSHED. bcmxtmcfg: Reinitialize port 0 traffictype 2 bcmxtmcfg: Normal(XTM/PTM) Mode enabled MemTotal: 28632 kB MemFree: 1868 kB Buffers: 2696 kB Cached: 8772 kB SwapCached: 0 kB Active: 3804 kB Inactive: 9948 kB Active(anon): 904 kB Inactive(anon): 1380 kB Active(file): 2900 kB Inactive(file): 8568 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 2304 kB Mapped: 2916 kB Slab: 9260 kB SReclaimable: 420 kB SUnreclaim: 8840 kB PageTables: 280 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 14316 kB Committed_AS: 6308 kB VmallocTotal: 1032148 kB VmallocUsed: 3420 kB VmallocChunk: 1022260 kB > cat /proc/mtd dev: size erasesize name mtd0: 0049a000 0049a000 "Physically mapped flash" > cat /proc/interrupts CPU0 7: 364626 BCM63xx timer 10: 324 BCM63xx brcm_10 12: 2789 BCM63xx brcm_12 21: 0 BCM63xx brcm_21 22: 0 BCM63xx brcm_22 23: 0 BCM63xx brcm_23 28: 0 BCM63xx brcm_28 29: 0 BCM63xx brcm_29 40: 0 BCM63xx brcm_40 41: 0 BCM63xx brcm_41 42: 0 BCM63xx brcm_42 48: 0 BCM63xx brcm_48 49: 0 BCM63xx brcm_49 50: 0 BCM63xx brcm_50 ERR: 0 > dmesg consoled:error:370.114:processInput:507:unrecognized command dmesg > > help ? help logout exit quit reboot df meminfo kill echo ifconfig ping ps pwd sysinfo tftp wlctl arp lan lanhosts restoredefault save swversion wlan tr064 cfm vcautohunt dhcpcondserv captiveurl > meminfo Total MDM Shared Memory Region : 1024KB Shared Memory Usable : 000929KB Shared Memory in-use : 000117KB Shared Memory free : 000812KB Shared Memory allocs : 023067 Shared Memory frees : 021132 Shared Memory alloc/free delta : 001935 Heap bytes in-use : 000016 Heap allocs : 000914 Heap frees : 000913 Heap alloc/free delta : 000001 > ifconfig bcmsw Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Base address:0x6a00 br0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 inet addr:192.168.254.254 Bcast:192.168.254.255 Mask:255.255.255.0 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:9646 (9.4 KiB) eth0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0.0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:38 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:9706 (9.4 KiB) eth1 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1.0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:36 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:9586 (9.3 KiB) eth2 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth2.0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:34 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:9466 (9.2 KiB) eth3 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth3.0 Link encap:Ethernet HWaddr C8:6C:87:5C:11:A9 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:9346 (9.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:90 errors:0 dropped:0 overruns:0 frame:0 TX packets:90 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6606 (6.4 KiB) TX bytes:6606 (6.4 KiB) sar Link encap:UNSPEC HWaddr FE-FF-FF-FF-FF-FF-FF-FF-00-00-00-00-00-00-00-00 UP NOTRAILERS RUNNING NOARP MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:50 Base address:0x5220 swc Link encap:UNSPEC HWaddr FE-FF-FF-FF-FF-FF-FF-FF-00-00-00-00-00-00-00-00 UP NOTRAILERS RUNNING NOARP MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0x6a40 > sysconfig consoled:error:175.526:processInput:507:unrecognized command sysconfig > sysinfo Number of processes: 42 12:03am up 3 min, load average: 1 min:0.03, 5 min:0.07, 15 min:0.03 total used free shared buffers Mem: 28632 26536 2096 0 2696 Swap: 0 0 0 Total: 28632 26536 2096 > swversion Usage: swversion show swversion help > swversion show 1.10(VFS.0)b3 >


> tftp BusyBox v1.00 (2012.01.04-03:14+0000) multi-call binary Usage: tftp [-p|-g] [-t i|c] [-f filename] tftp_server_ip Update firmware image and configuration data from OR backup configuration data to a tftp server. Examples: -g -t i -f filename server_ip Get (flash) broadcom or whole image to modem -g -t c -f filename server_ip Get (flash) config file to modem -p -f filename server_ip Put (backup) config file to [[docs:guide-user:troubleshooting:tftpserver|tftpd server]] > tftp -g -t i -f openwrt-96368MVWG-generic-squashfs-cfe.bin 192.168.254.33 exit mcpd!! MemTotal: 28632 kB MemFree: 11364 kB Buffers: 152 kB Cached: 2908 kB SwapCached: 0 kB Active: 2336 kB Inactive: 2216 kB Active(anon): 628 kB Inactive(anon): 864 kB Active(file): 1708 kB Inactive(file): 1352 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 1512 kB Mapped: 2636 kB Slab: 9088 kB SReclaimable: 264 kB SUnreclaim: 8824 kB PageTables: 184 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 14316 kB Committed_AS: 3960 kB VmallocTotal: 1032148 kB VmallocUsed: 3420 kB VmallocChunk: 1022260 kB Allocating 8388628 bytes for flash image. Memory allocated Got image via tftp, total image size: 3276804 tftp:error:556.544:verifyZyXELModelId:143:Not find ZyXEL identify, just fall through Flashing root file system and kernel... .................................................... ****** DDR->DSLCorePhaseCntl=0 ****** ý CFE version 1.0.37-107.23 for BCM96368 (32bit,SP,BE) Build Date: 12/27/2011 (FuChia@MsgSW4-SerVer) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Checking Reset button on EXT INTR 0 Checking Reset button on EXT INTR 0 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Board Id (0-15) : 96368MVWG Number of MAC Addresses (1-32) : 10 Base MAC Address : c8:6c:87:5c:11:a9 PSI Size (1-128) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Wait for Multiboot Service Packet... 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80010000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80010000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 1 buffers found. Closing DMA Channels. Starting program at 0x80010000 [ 0.000000] Linux version 3.10.21 (thepeople@trabant) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38990) ) #1 Tue Dec 3 08:27:54 CET 2013 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 32MB of RAM installed [ 0.000000] registering 38 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-107.23 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96368MVWG [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Memory: 28752k/32768k available (2440k kernel code, 4016k reserved, 704k data, 244k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 512 [ 0.044000] NET: Registered protocol family 16 [ 0.052000] registering PCI controller with io_map_base unset [ 0.056000] registering PCI controller with io_map_base unset [ 0.064000] bio: create slab <bio-0> at 0 [ 0.068000] PCI host bridge to bus 0000:00 [ 0.072000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.076000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff] [ 0.080000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.096000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.100000] PCI host bridge to bus 0000:01 [ 0.104000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff] [ 0.108000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff] [ 0.112000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.116000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.120000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff] [ 0.124000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff] [ 0.128000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff] [ 0.132000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05] [ 0.136000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff] [ 0.140000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff] [ 0.144000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff] [ 0.148000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003) [ 0.152000] Switching to clocksource MIPS [ 0.160000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.188000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.252000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.260000] NET: Registered protocol family 2 [ 0.264000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.272000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.280000] TCP: Hash tables configured (established 512 bind 512) [ 0.284000] TCP: reno registered [ 0.288000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.296000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.304000] NET: Registered protocol family 1 [ 0.308000] audit: initializing netlink socket (disabled) [ 0.316000] type=2000 audit(0.316:1): initialized [ 0.320000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.324000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.336000] msgmni has been set to 56 [ 0.340000] io scheduler noop registered [ 0.344000] io scheduler deadline registered (default) Ę[ 0.360000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart [ 0.360000] console [ttyS0] enabled, bootconsole disabled [ 0.372000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.380000] physmap platform flash device: 08000000 at 18000000 [ 0.384000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb [ 0.396000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.400000] Amd/Fujitsu Extended Query version 1.1. [ 0.408000] number of CFI chips: 1 [ 0.412000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MVWG [ 0.420000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.424000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11ff00 [ 0.432000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length 6c0000 [ 0.440000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000 [ 0.448000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000 [ 0.456000] bcm63xxpart: Spare partition is offset 330004 and length 4bfffc [ 0.460000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 0.468000] Creating 5 MTD partitions on "physmap-flash.0": [ 0.476000] 0x000000000000-0x000000010000 : "CFE" [ 0.480000] 0x000000010100-0x000000130000 : "kernel" [ 0.488000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.500000] 0x000000130000-0x0000007f0000 : "rootfs" [ 0.508000] mtd: device 2 (rootfs) set to be root filesystem [ 0.512000] mtd: partition "rootfs_data" created automatically, ofs=0x330000, len=0x4c0000 [ 0.520000] 0x000000330000-0x0000007f0000 : "rootfs_data" [ 0.528000] 0x0000007f0000-0x000000800000 : "nvram" [ 0.536000] 0x000000010000-0x0000007f0000 : "linux" [ 0.544000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.592000] b53_common: found switch: BCM63xx, rev 0 [ 0.596000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.608000] TCP: cubic registered [ 0.608000] NET: Registered protocol family 17 [ 0.616000] Bridge firewalling registered [ 0.620000] 8021q: 802.1Q VLAN Support v1.8 [ 0.632000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.640000] Freeing unused kernel memory: 244K (80323000 - 80360000) procd: Console is alive procd: - watchdog - procd: - preinit - ifconfig: SIOCGIFFLAGS: No such device Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 4.428000] Button Hotplug driver version 0.4.1 mount_root: jffs2 is not ready - EOF marker found ifconfig: SIOCGIFFLAGS: No such device procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 8.292000] NET: Registered protocol family 10 [ 8.316000] nf_conntrack version 0.5.0 (453 buckets, 1812 max) [ 8.332000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.356000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 [ 8.364000] Backport generated by backports.git backports-20130802-0-gdb67a3f [ 8.376000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.436000] xt_time: kernel timezone is -0000 [ 8.468000] cfg80211: Calling CRDA to update world regulatory domain [ 8.488000] cfg80211: World regulatory domain updated: [ 8.492000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 8.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.508000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 8.516000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 8.524000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 8.532000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 8.540000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 8.652000] PPP generic driver version 2.4.2 [ 8.660000] NET: Registered protocol family 24 [ 8.704000] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 8.756000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 8.788000] Broadcom 43xx driver loaded [ Features: PNL ] [ 16.752000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 16.772000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 16.776000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 17.472000] device eth0.1 entered promiscuous mode [ 17.476000] device eth0 entered promiscuous mode [ 17.488000] br-lan: port 1(eth0.1) entered forwarding state [ 17.492000] br-lan: port 1(eth0.1) entered forwarding state [ 18.460000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 19.496000] br-lan: port 1(eth0.1) entered forwarding state done. [ 58.092000] jffs2: notice: (547) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. procd: - init complete - BusyBox v1.19.4 (2013-12-03 08:14:57 CET) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M -----------------------------ujjjjjjjj BARRIER BREAKER (Bleeding Edge, r38990) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#


OpenWrt debug level 4 pastebin: http://pastebin.com/KCBeMZif

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1