Comtrend VR-3025un (Jazztel, Spain)
The VR-3025un was given away with a Jazztel Fibre VDSL2 subscription in Spain (Europe), The device includes a DSL VDSL2/ADSL2+ Modem Combo, Wireless N 802.11/a/b/g/n upto 300 Mbps, 4 Wired/LAN Ethernet Ports.
The VDSL2/ADSL2+ transceiver delivers 100 Mb/s downstream and 50 Mb/s upstream (100 Mb/s upstream with external AFE), enhanced QoS for IPTV video, dual-latency framing, ATM or PTM physical layer, DSL channel bonding, and embedded operations channels for remote management of the CPE. ~ taken from broadcam's website https://www.broadcom.com/products/broadband/xdsl/bcm6368#overview
Supported Versions
Hardware Highlights
Installation
Unlike the CFE found in other Comtrend routers pressing reset button does not give access to the web failsafe.
At this moment there are only two ways to load OpenWrt:
- Original firmware web management.
- Stopping boot process and accessing CFE.
Hardware
Info
| Architecture | MIPS |
|---|---|
| Vendor | Broadcom |
| bootloader | cfe |
| Board ID | 96368M-1341N |
| System-On-Chip | Broadcom BCM6368 rev. b2 |
| CPU/Speed | BMIPS4350 / 400 MHz |
| Flash-Chip | MX29LV640EBTI |
| Flash size | 8 MiB |
| RAM-Chip | 2xEM6AA160TSA-5G / DDR-400 |
| RAM size | 64 MiB |
| Wireless | Mini-PCI BCM43222 (14e4:4351) 802.11b/g/n |
| Ethernet | BCM6368 integrated |
| USB | yes |
| Antenna | 2x |
| Serial | Yes |
| JTAG | Yes |
Photos
Case:
Board:
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
There are pads for soldering a JTAG in the bottom of the board.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Parameters:
- Baudrate: 115200
- Data bits: 8
- Parity: None
- Stop bits: 1
GPIO
LEDs
Read: System configuration: Leds to configure the leds
| Pin | Event | Active |
|---|---|---|
| 2 | dsl (green) | Low |
| 5 | inet (green) | High |
| 22 | power (green) | High |
| 24 | power (red) | High |
| 31 | inet (red) | High |
Buttons
→ hardware.button on howto use and configure the hardware button(s).
| Pin | Event | Active |
|---|---|---|
| 34 | Reset | Low |
Bootlogs
OEM Bootlog
CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE) Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-14) : 96368M-1341N Number of MAC Addresses (1-32) : 11 Base MAC Address : 64:68:0c:xx:xx:xx PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80014230 Decompression OK! Entry at 0x80014230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80014230 Linux version 2.6.30 (jim@broadcom_v060.comtrend.com) (gcc version 4.4.2 (Buildroot 2010.02-git) ) # 1 Mon Mar 22 13:48:43 CST 2010 Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB 96368M-1341N prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 8030f0f0, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60460k/64512k available (2566k kernel code, 4032k reserved, 506k data, 124k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 net_namespace: 748 bytes NET: Registered protocol family 16 Total Flash size: 8192K with 135 sectors registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff] pci 0000:00:01.0: supports D1 D2 pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff] BLOG v2.1 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 118 io scheduler noop registered (default) Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8010100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8017 is enabled Invalid External Interrupt definition Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Mar 22 2010 13:48:19 Broadcom Logger v0.1 Mar 22 2010 13:48:14 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 124k freed init started: BusyBox v1.00 (2010.03.22-05:49+0000) multi-call binary BusyBox v1.00 (2010.03.22-05:49+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Packet Flow Cache Char Driver v2.1 Feb 12 2010 17:14:58 Registered<242> NBUFF v1.0 Initialized Broadcom Packet Flow Cache learning via BLOG enabled. Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Constructed Broadcom Packet Flow Cache v2.1 Feb 12 2010 17:14:57 Broadcom Packet CMF (Experimental) Char Driver v0.1 Feb 12 2010 17:14:55 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Feb 12 2010 17:14:55 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 Mar 22 2010 13:48:16 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Feb 12 2010 17:14:56 Registered Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Feb 12 2010 17:14:56 Registered Broadcom Packet CMF (Experimental) ENABLED. eth0: MAC Address: 64:68:0C:xx:xx:xx eth1: MAC Address: 64:68:0C:xx:xx:xx eth2: MAC Address: 64:68:0C:xx:xx:xx eth3: MAC Address: 64:68:0C:xx:xx:xx Broadcom BCM6368B2 USB Network Device v0.4a Mar 22 2010 13:48:17 usb0: MAC Address: 64 68 0C xx xx xx usb0: Host MAC Address: 64 68 0C xx xx xx USBD Initialization done status 0 USB Link DOWN. message received before monitor task is initialized kerSysSendtoMonitorTask PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl0: Broadcom BCM4351 802.11 Wireless Controller 5.10.141.0.cpe4.405.1 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs Broadcom 802.1Q VLAN Interface, v0.1 ===== Comtrend Release Version L411-405JAZ-C02_R02 ===== ssk:error:5.264:mdm_adjustForBackwardCompatibility:149:configuration is newer than 3.0, so no adjust needed interface atm0.1 does not exist! SIOCGIFFLAGS: No such device interface ptm0.1 does not exist! SIOCGIFFLAGS: No such device ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode device wl0 entered promiscuous mode WLmngr Daemon is running optarg=0 shmId=0 wlevt_init@107: opened loopback socket 4 wlevt is ready fobr0: port 4(wl0) entering forwarding state r new msg... Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode BcmAdsl_Initialize=0xC0100070, g_pFnNotifyCallback=0xC012BC34 Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 065, PhaseValue = -050, PhaseCntl = 0x3FBF0000 QPROC is aligned, i = 067, PhaseValue = -050, PhaseCntl = 0x3FBF3FBD Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA3FFFFF8, 0x150A57 0xCC5DAA55 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xC164C => 0xE1078 *** AdslCoreSharedMemInit: shareMemAvailable=126816 AdslCoreHwReset: AdslOemDataAddr = 0xA3FAA24C dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered monitor task is initialized pid= 236 device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 4(wl0) entering forwarding state br0: port 4(wl0) entering disabled state There is no Predefined DevicePin in CFE WPS Device PIN = 31957199 Setting SSID "JAZZTEL_A17E" Setting SSID "wl0_Guest1" Setting SSID "wl0_Guest2" Setting SSID "wl0_Guest3" wlctl: Unsupported chanspec 0x2d03 selected 1l (0x2d03) br0: port 4(wl0) entering forwarding state device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 4(wl0) entering forwarding state Reaped 883 UPnP daemon is ready to run
OpenWrt
CFE version 1.0.37-105.22-1 for BCM96368 (32bit,SP,BE) Build Date: Fri Mar 19 11:53:33 CST 2010 (jojopo@broadcom_v060.comtrend.com) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB Total Flash size: 8192K with 135 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-14) : 96368M-1341N Number of MAC Addresses (1-32) : 11 Base MAC Address : 64:68:0c:xx:xx:xx PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80010000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80010000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80010000 [ 0.000000] Linux version 3.8.11 (pepe@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36529) ) #1 Sat Jun 22 15:40:44 CEST 2013 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 38 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-105.22 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96368M-1341N [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console= ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 61400k/65536k available (2336k kernel code, 4136k reserved, 607k data, 252k i nit, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 512 [ 0.040000] NET: Registered protocol family 16 [ 0.048000] registering PCI controller with io_map_base unset [ 0.060000] bio: create slab <bio-0> at 0 [ 0.064000] PCI host bridge to bus 0000:00 [ 0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.072000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.076000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.092000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x3000ffff] [ 0.096000] Switching to clocksource MIPS [ 0.104000] NET: Registered protocol family 2 [ 0.108000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.116000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.120000] TCP: Hash tables configured (established 512 bind 512) [ 0.128000] TCP: reno registered [ 0.132000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.136000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.144000] NET: Registered protocol family 1 [ 0.152000] audit: initializing netlink socket (disabled) [ 0.156000] type=2000 audit(0.156:1): initialized [ 0.164000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.168000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.180000] msgmni has been set to 119 [ 0.184000] io scheduler noop registered [ 0.188000] io scheduler deadline registered (default) z+H 0.200000] console [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart [ 0.200000] console [ttyS0] enabled, bootconsole disabled [ 0.216000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.220000] physmap platform flash device: 08000000 at 18000000 [ 0.228000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb [ 0.240000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.244000] Amd/Fujitsu Extended Query version 1.1. [ 0.248000] number of CFI chips: 1 [ 0.252000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1341N [ 0.260000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.268000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00 [ 0.276000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 6d0000 [ 0.284000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000 [ 0.288000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000 [ 0.296000] bcm63xxpart: Spare partition is offset 350004 and length 49fffc [ 0.304000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 0.312000] Creating 5 MTD partitions on "physmap-flash.0": [ 0.316000] 0x000000000000-0x000000010000 : "CFE" [ 0.324000] 0x000000010100-0x000000120000 : "kernel" [ 0.328000] mtd: partition "kernel" must either start or end on erase block boundary or be smalle r than an erase block -- forcing read-only [ 0.344000] 0x000000120000-0x0000007f0000 : "rootfs" [ 0.352000] mtd: partition "rootfs" set to be root filesystem [ 0.356000] mtd: partition "rootfs_data" created automatically, ofs=350000, len=4A0000 [ 0.364000] 0x000000350000-0x0000007f0000 : "rootfs_data" [ 0.372000] 0x0000007f0000-0x000000800000 : "nvram" [ 0.380000] 0x000000010000-0x0000007f0000 : "linux" [ 0.388000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.432000] b53_common: found switch: BCM63xx, rev 0 [ 0.436000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.444000] TCP: cubic registered [ 0.448000] NET: Registered protocol family 17 [ 0.452000] 8021q: 802.1Q VLAN Support v1.8 [ 0.464000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.472000] Freeing unused kernel memory: 252k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - [ 5.992000] jffs2: notice: (298) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found. switching to jffs2 - init - Please press Enter to activate this console. [ 7.400000] compat-drivers backport release: compat- drivers-2013-03-28-5 [ 7.408000] Backport based on wireless-testing.git master-2013-04-16 [ 7.412000] compat.git: wireless-testing.git [ 7.464000] cfg80211: Calling CRDA to update world regulatory domain [ 7.468000] cfg80211: World regulatory domain updated: [ 7.476000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 7.484000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.492000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 7.500000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 7.508000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.516000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 7.828000] NET: Registered protocol family 10 [ 8.188000] SCSI subsystem initialized [ 8.360000] usbcore: registered new interface driver usbfs [ 8.364000] usbcore: registered new interface driver hub [ 8.372000] usbcore: registered new device driver usb [ 8.840000] Button Hotplug driver version 0.4.1 [ 9.432000] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 9.948000] PPP generic driver version 2.4.2 [ 10.676000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.944000] NET: Registered protocol family 24 [ 11.096000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.120000] ehci-platform: EHCI generic platform driver [ 11.228000] ehci-platform ehci-platform: EHCI Host Controller [ 11.232000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 11.240000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500 [ 11.260000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 11.268000] hub 1-0:1.0: USB hub found [ 11.272000] hub 1-0:1.0: 2 ports detected [ 11.404000] nf_conntrack version 0.5.0 (963 buckets, 3852 max) [ 12.376000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 12.676000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 12.684000] ohci-platform ohci-platform: Generic Platform OHCI Controller [ 12.692000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 12.700000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600 [ 12.764000] hub 2-0:1.0: USB hub found [ 12.768000] hub 2-0:1.0: 1 port detected [ 12.904000] Initializing USB Mass Storage driver... [ 12.912000] usbcore: registered new interface driver usb-storage [ 12.916000] USB Mass Storage support registered. [ 17.436000] device eth0 entered promiscuous mode [ 17.440000] br-lan: port 1(eth0) entered forwarding state [ 17.448000] br-lan: port 1(eth0) entered forwarding state [ 18.432000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.452000] br-lan: port 1(eth0) entered forwarding state