Vodafone Power Station / Vox30

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

This is the Vodafone Vox30 CPE shipped for different types of fixed line technology in various countries. It supports ADSL2+/VDSL2 broadband connections as well as FTTH connections (either via its Ethernet WAN port or the side-mounted SFP port). It also provides two FXS ports for VoIP-to-POTS telephony gateway features as well as two USB 2.0 ports (one of them is recessed and meant to house an internet key).

There are two known models of this device, one made by Technicolor (THG3000) and one made by Sercomm (SHG3000). Both models share the same hardware and firmware.

The Vodafone Vox30 has been marketed under different names, which are:

Vodafone Power Station (SHG3000, distributed in Italy)
Vodafone Gigabox (SHG3000, distributed in Ireland)
Vodafone Wi-Fi Hub (THG3000, distributed in the UK)

Not supported.

SoC: There is support in kernel mainline: https://elixir.bootlin.com/linux/v5.10.31/source/arch/arm/mach-bcm/Kconfig#L185.
But a new Broadcom ARM bcm63xx target is required for Openwrt support.
Wifi: BCM4360 no driver in Linux Kernel and likely missing firmware brcmfmac

Vendor	Vodafone Clone Model	SoC	CPU Speed	RAM	NAND Flash	WLAN Hardware	WLAN 2.4	WLAN 5.0	100M ports	Gbit ports	Modem	USB
Sercomm	SHG3000	Broadcom BCM63136	2x 1 GHz	512 MiB	256 MiB	Broadcom BCM4360, Broadcom BCM4366	b/g/n	a/n/ac	-	5	VDSL2 (35b) / G.fast	2x 2.0
Technicolor	THG3000	Broadcom BCM63136	2x 1 GHz	512 MiB	256 MiB	Broadcom BCM4360, Broadcom BCM4366	b/g/n	a/n/ac	-	5	VDSL2 (35b) / G.fast )	2x 2.0

Please tell if these details refer to Sercomm or Technicolor hardware version

Architecture	ARM
Vendor	Broadcom
Bootloader	?
System-On-Chip	Broadcom BCM63136SVKFSBG
CPU/Speed	Cortex-A9 MPCore @ 1 GHz
Flash-Chip	Macronix MXIC MX8CLF2G18AC-11
Flash size	256 MiB
RAM	512 MiB
Wireless 2.4 GHz	Broadcom BCM4360, b/g/n, 3×3, 450 Mbit
Wireless 5 GHz	Broadcom BCM4366, a/n/ac, 4×4, MU-MIMO, 1733 Mbit
Ethernet	5x 10/100/1000 BASE-TX Ethernet Interface (1x WAN, 4x LAN)
xDSL	ADSL1/2/2+ VDSL1 VDSL2 G.FAST G.IMP
USB	2x 2.0
Serial	Yes
JTAG	?
Power	External, 12 V 2.5 A

The FXS ports are black in the SHG3000 model, while in the THG3000 model are green.
The DSL port has similar cosmetic differences; It's grey and labeled “DSL” in the SHG3000 model, while in the THG3000 model it's red and labeled “Internet”.

Sercomm SHG3000

Front panel
Back panel
Top view
Bottom view
Back panel (inside)	$ASCII�� ALCSIIF5�d��E��I��1T�ط��z��3��1��h��m��h��m��S ��jn�n��m�h�m�h��G��y��ALCE��FAFA��2��FAFA'��N��2sI��I��IN��%�C��-3��~;��~;��~;��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��\�h��P��B��FAFA��F��\|��)��Έ��)�+��+�+�� P_CRA00...$
Front panel (inside)

Sercomm SHG3000

Front	$ASCII�� ALCSIIF5��xH��>��a��~����5��f��0k��f��Tk��e�p�v��Tk�fXk�f8��G��y��ALCE��FAFA��2��FAFA��eyo��I��o��D"��ۅY��\��FAFA��H��`��jj��)������=�I��W��P_CRA00...$
Back
SoC

(SGH3000) Remove the three screws on the bottom and then remove the USB port cover on the back where the Vodafone key k5160 is housed. Remove the bottom plate by pulling it. Then pull apart the front starting from the top, where the two buttons are. The buttons stay attached to the front part.

The PCB is fixed on the front with six star screws.

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port For the Sercomm variant the pinout is not known.

For the Technicolor variant, the serial header is J203. From the notch, 3.3V, GND, TXD, RXD.

Serial connection parameters for THG3000	115200, 8N1

For the Sercomm variant the serial header is J4, From the arrow, GND, TXD, 3v3, RXD. Baudrate is 115200.

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Sercomm SHG3000

---- BTRM V1.6 PMCS AFEL PWRZ MEML PMCD MEMP CODE ZBSS MAIN CACH OTP? OTPP ROTB SCBT NAND IMG? IMGL HDR? HDRP MCV? KEY? KEYA MID? MIDP MCVA SBI? SBIA PASS ---- HELO 4.1605-1.0.38-118.3 CPU0 PMCM PMCS AFEL PWRZ MEML APMT PMCD L1CD MMUI CODE ZBBS MAIN NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes DRAM MCB chksum 0xf53f590b DDR3-1600 CL11 512MB High Temperature ASR Changed Byte Lane LDE Changed Byte Lane LDE PASS NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes FPS0 FDPM PMOK GFOK F002 RAM1 NAN9 NAN3 RFS0 BTL? BTLA PASS FKOK GKOK NAN5 Base: 5.2_03patch1xpon CFE version 1.0.38-161.189 for BCM963138 (32bit,SP,LE) Build Date: Wed Jul 31 14:42:26 CST 2019 (michelle@Ubuntu) Copyright (C) 2000-2015 Broadcom Corporation. Boot Strap Register: 0x7dfffc2f Chip ID: BCM63136_B0, ARM Cortex A9 Dual Core: 1000MHz Total Memory: 536870912 bytes (512MB) NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes NAND flash device: , id 0xc2da block 128KB size 262144KB pmc_init:PMC using DQM mode Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host/tftp (f/h/c) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Default host ramdisk file name : Default ramdisk store address : Default DTB file name : Board Id : 963138REF Number of MAC Addresses (1-64) : 16 Base MAC Address : 0c:67:14:5c:55:00 PSI Size (1-128) KBytes : 48 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 MC memory allocation (MB) : 4 TM memory allocation (MB) : 48 DHD 0 memory allocation (MB) : 14 DHD 1 memory allocation (MB) : 14 DHD 2 memory allocation (MB) : 0 WLan Feature : 0x00 Voice Board Configuration (0-28) : LE9642_ZSI_BB Partition 1 Size (MB) : Partition 2 Size (MB) : Partition 3 Size (MB) : Partition 4 Size (MB) (Data) : 4MB Initalizing switch low level hardware. pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0. Software Resetting Switch ... Done. Waiting MAC port Rx/Tx to be enabled by hardware ...Done Disable Switch All MAC port Rx/Tx SC_DEBUG: Nand Partition Table Magic Found at c0000. Enable Switch MAC Port Rx/Tx, set PBVLAN to FAN out, set switch to NO-STP. RDP TM memory = 20MB, MC memory = 4MB : Max Possible Bufs <8192> of size <2048>; Allocating <7680> bufs; RDP enum <2> Creating CPU ring for queue number 0 with 32 packets descriptor=0x00f83068, size_of_entry 16 Done initializing Ring 0 Base=0x42a1ba60K End=0x42a1bc60K calculated entries= 32 RDD Base=2a1ba60K descriptor=0x00f83068 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 *************************************************** Sercomm Boot Version 5.0.0.0, at Jul 31 2019, 14:42:28 *************************************************** Find bootFlag successfully. Booting from first image (0x00a40000) ... KFS Authenticate ... OK! LIB Authenticate ... OK! Checksum ... OK! Decompression Image.Src Addr:0x2f89e28,Des Addr:0x8000 Decompression LZMA Image OK! Entry at 0x00008000 Closing network. Starting program at 0x00008000 /memory = 0x20000000 bytes @ 0x0 Appending NVRAM to dtb, ret:0 Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 4.1.38+ (lip@PD7-2) (gcc version 5.3.0 (Buildroot 2016.02) ) #1 SMP PREEMPT Fri Aug 11 17:39:45 CST 2023 CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: Broadcom BCM963138 Reserved memory: phys 0x0fd00000 size 0x00300000 for adsl Reserved memory: phys 0x0cc00000 size 0x03000000 for tm Reserved memory: phys 0x0c800000 size 0x00400000 for mc Reserved memory: phys 0x0ba00000 size 0x00e00000 for dhd0 Reserved memory: phys 0x0ac00000 size 0x00e00000 for dhd1 Memory policy: Data cache writealloc creating a MT_MEMORY_NONCACHED device at physical address of 0x0fd00000 to virtual address at 0xcfd00000 with size of 0x300000 byte for adsl creating a MT_MEMORY_NONCACHED device at physical address of 0x0cc00000 to virtual address at 0xccc00000 with size of 0x3000000 byte for tm creating a MT_MEMORY_NONCACHED device at physical address of 0x0c800000 to virtual address at 0xcc800000 with size of 0x400000 byte for mc creating a MT_MEMORY_NONCACHED device at physical address of 0x0ba00000 to virtual address at 0xcba00000 with size of 0xe00000 byte for dhd0 creating a MT_MEMORY_NONCACHED device at physical address of 0x0ac00000 to virtual address at 0xcac00000 with size of 0xe00000 byte for dhd1 creating a MT_MEMORY_NONCACHED device at physical address of 0x0ab00000 to virtual address at 0xcab00000 with size of 0x100000 byte for Kernel Crash pmc_init:PMC using DQM mode pmc_init:fc9c 35f0355 4b004b PERCPU: Embedded 11 pages/cpu @dfb5a000 s15616 r8192 d21248 u45056 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 108416 Kernel command line: console=ttyS0,115200 root=mtd:rootfs ro rootfstype=jffs2 irqaffinity=0 coherent_pool=1M cpuidle_sysfs_switch PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 426996K/438272K available (4731K kernel code, 322K rwdata, 1304K rodata, 200K init, 266K bss, 11276K reserved, 0K cma-reserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc05ed1bc (6037 kB) .init : 0xc05ee000 - 0xc0620000 ( 200 kB) .data : 0xc0620000 - 0xc0670b40 ( 323 kB) .bss : 0xc0670b40 - 0xc06b3704 ( 267 kB) Preemptible hierarchical RCU implementation. NR_IRQS:256 Cortex A9 MPCORE GIC init DIST at fc01f000, CPU_IF at fc01e100 L2C: platform modifies aux control register: 0x02070000 -> 0x6a450000 L2C: DT/platform modifies aux control register: 0x02070000 -> 0x6a450000 L2C: DT/platform tries to modify or specify cache size L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 I prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 16 ways, 512 kB L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x6e450001 map_hw_timer_interrupt,127: interrupt_id 96 map_hw_timer_interrupt,127: interrupt_id 97 map_hw_timer_interrupt,127: interrupt_id 98 map_hw_timer_interrupt,127: interrupt_id 99 clocksource timer_cs: mask: 0x3fffffff max_cycles: 0x3fffffff, max_idle_ns: 9556302227 ns sched_clock: 30 bits at 50MHz, resolution 20ns, wraps every 10737418230ns console [ttyS0] enabled Calibrating delay loop... 1319.93 BogoMIPS (lpj=659968) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Initializing cgroup subsys blkio Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer CPU: Testing write buffer coherency: ok Broadcom Logger v0.1 Setting up static identity map for 0x8220 - 0x8254 Brought up 2 CPUs SMP: Total of 2 processors activated (2650.11 BogoMIPS). CPU: All CPU(s) started in SVC mode. clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns NET: Registered protocol family 16 DMA: preallocated 1024 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu Successfully retrieved NVRAM data from dtb Failed to retrieve boot CFE version from dtb! irq: no irq domain found for /interrupt-controller@80000000 ! ++++ Powering up USB blocks SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated skb_free_task created successfully with start budget 256 gbpm_do_work scheduled [0;34mBLOG v3.0 Initialized[0m BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 initialized Broadcom GBPM v0.1 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 Switched to clocksource timer_cs NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 futex hash table entries: 512 (order: 2, 16384 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher ntfs: driver 2.1.32 [Flags: R/W]. jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. fuse init (API version 7.23) io scheduler noop registered (default) brd: module loaded loop: module loaded Broadcom NAND controller (BrcmNand Controller) mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 B4: NandSelect=40000001, nandConfig=26152300, chipSelect=0 brcmnand_read_id: CS0: dev_id=c2da9095 After: NandSelect=00000001, nandConfig=26152300 DevId c2da9095 may not be supported. Will use config info Spare Area Size = 16B/512B Block size=00020000, erase shift=17 NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff ECC level changed to 4 OOB size changed to 16 BrcmNAND mfg 0 0 UNSUPPORTED NAND CHIP 256MB on CS0 Found NAND on CS0: ACC=c3840010, cfg=26152300, flashId=c2da9095, tim1=65324458, tim2=80000e54 BrcmNAND version = 0x80000700 256MB @00000000 brcmnand_scan: B4 nand_select = 00000001 brcmnand_scan: After nand_select = 00000001 handle_acc_control: default CORR ERR threshold 3 bits ACC: 16 OOB bytes per 512B ECC step; from ID probe: 16 page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17 Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000 ECC layout=brcmnand_oob_bch4_2k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=35, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_slc_bch4_main_descr brcmnand_reset_corr_threshold: default CORR ERR threshold 3 bits for CS0 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_ncm ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ehci-platform ehci-platform.0: EHCI Host Controller ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 ehci-platform ehci-platform.0: irq 105, io mem 0x8000c300 ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-pci: OHCI PCI platform driver ohci-platform: OHCI generic platform driver ohci-platform ohci-platform.0: Generic Platform OHCI controller ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2 ohci-platform ohci-platform.0: irq 104, io mem 0x8000c400 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usblp i2c /dev entries driver brcmboard registered brcmboard: brcm_board_init entry print_rst_status: Last RESET due to POR reset DYING GASP IRQ Initialized and Enabled Serial: BCM63XX driver $Revision: 3.00 $ [0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)[0m ttyS0 at MMIO 0xfffe8600 (irq = 64, base_baud = 921600) is a BCM63XX ttyS1 at MMIO 0xfffe8620 (irq = 65, base_baud = 921600) is a BCM63XX I2C SFP Module Driver Loaded BPM: tot_mem_size=536870912B (512MB), buf_mem_size <15%> =80530635B (76MB), num of buffers=39945, buf size=2016 Broadcom BPM Module Char Driver v0.1 Registered<3004>[0m PCIe HCD (impl1) bcm963xx-pcie: found core [0] Rev [3.01] with 1 Lanes bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers disabled pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x905fffff] pci 0000:01:00.0: BAR 2: assigned [mem 0x90000000-0x903fffff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x90400000-0x90407fff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x90000000-0x905fffff] pcieport 0000:00:00.0: enabling device (0140 -> 0142) pcieport 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 bcm963xx-pcie: found core [1] Rev [3.01] with 1 Lanes bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00 pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff] pci_bus 0001:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers disabled pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff] pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit] pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit] pci 0001:00:00.0: PCI bridge to [bus 01] pci 0001:00:00.0: bridge window [mem 0xa0000000-0xa0bfffff] pci 0001:00:00.0: bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref] pcieport 0001:00:00.0: enabling device (0140 -> 0142) pcieport 0001:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 pci 0001:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (6671 buckets, 26684 max) ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team Initializing XFRM netlink socket NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered L2TP core: blog_l2tp_rcv_check l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 Registering SWP/SWPB emulation handler random: nonblocking pool is initialized VFS: Mounted root (jffs2 filesystem) readonly on device 31:6. Freeing unused kernel memory: 200K (c05ee000 - c0620000) jffs2: Empty flash at 0x0056cbf4 ends at 0x0056d000 ubi0: attaching mtd9 ubi0: scanning is finished ubi0: attached mtd9 (name "package", size 80 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 640, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 1652056159 ubi0: available PEBs: 0, total reserved PEBs: 640, PEBs reserved for bad PEB handling: 13 ubi0: background thread "ubi_bgt0d" started, PID 448 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 453 UBIFS (ubi0:0): recovery needed UBIFS (ubi0:0): recovery completed UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "package" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 77709312 bytes (74 MiB, 612 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID DD58E379-6451-42C7-8DE0-9BE67F63FD8C, small LPT model jffs2: notice: (423) check_node_data: wrong data CRC in data node at 0x00e69f98: read 0x71770edf, calculated 0xe1a18d97. rdpa: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint tm_base_addr 0xccc00000, size 50331648, tm_base_addr_phys 0x0cc00000 mc_base_addr 0xcc800000, size 4194304, mc_base_addr_phys 0x0c800000 RDP reserved memory has been adjusted TM: base_addr = 0xcd000000, phys_addr = 0x0d000000, size = 34MB MC: base_addr = 0xcc800000, phys_addr = 0x0c800000, size = 8MB RDP TM memory = 34MB, MC memory = 8MB : Max Possible Bufs <19660> of size <2048>; Allocating <15360> bufs; RDP enum <5> WARNING!RDP reserved memories are wasting 10MB of memory, please adjust your reserved memory size ++++Runner gso_desc_pool created successfully brcmchipinfo: brcm_chipinfo_init entry bcmxtmrt: Broadcom BCM3136B0 ATM/PTM Network Device v0.9 Created XTM Rx queue 5 with size 256,Descriptor base=00c1a000 Created XTM Rx queue 6 with size 256,Descriptor base=00c1c000 NBUFF v1.0 Initialized [0;36;44mTotal # of labels = 62[0m [0;36;44mInitialized fcache state[0m [0;36;44mBroadcom Packet Flow Cache Char Driver v4.0 Registered<3002>[0m Created Proc FS /procfs/fcache [0;36;44mBroadcom Packet Flow Cache registered with netdev chain[0m [0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.[0m [0;35m[FHW] pktDbgLvl[0xbf342424]=0[0m [0;34m[FHW] fhw_construct: [0m [0;36;44mInitialized Fcache HW accelerator layer state[0m flwStatsThread created. numFlwsPerPoll 546 maxFlwIdx 16383 [0;36;44mConstructed Broadcom Packet Flow Cache v4.0[0m bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#0 Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#1 Switch Port#3 (Internal MUX Port#0) connects to Crossbar Port#4 Unused MUX Internal Port#1 connects to Crossbar External Port#2 Cross Bar MUX Config : Internal Port 00 maps to External Port 04 <reg_val : 0x0000000c> Cross Bar MUX Config : Internal Port 01 maps to External Port 02 <reg_val : 0x00000014> Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014> Cross Bar MUX Config : Internal Port 02 maps to External Port 00 <reg_val : 0x00000014> GPIO 36 is assigned to Serdes Fiber Signal Detection. Setting SGMII Calibration value to 0x9 GPIO Pin -32731 is configured as SPF MOD_ABS for module insertion detection Broadcom BCM63136_B0 Ethernet Network Device v0.1 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered ++++ disabling GSO on logical_port=0 dev=eth0 eth0: <Int sw port: 0> <Logical : 00> MAC : 0C:67:14:5C:55:00 Chip Physical Port 9, Cross Bar Port 0, PHY_ID <0x06180006:0x06:Serdes PHY > Chip Physical Port 10, Cross Bar Port 1, PHY_ID <0x0007f00c:0x0c:Internal PHY > eth1: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008:0x08:Internal PHY> MAC:0C:67:14:5C:55:00 eth2: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009:0x09:Internal PHY> MAC:0C:67:14:5C:55:00 eth3: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a:0x0a:Internal PHY> MAC:0C:67:14:5C:55:00 eth4: <Ext sw port: 3> <Logical : 11> MAC : 0C:67:14:5C:55:00 Chip Physical Port 13, Cross Bar Port 4, PHY_ID <0x0007f00b:0x0b:Internal PHY > Ethernet Auto Power Down and Sleep: Enabled Cross bar port 1 of Int switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 1; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 2; Adv capability change : MII=0x01e1, GMII=0x0f00 Cross bar port 4 of Ext switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00 All Port Bit Map: 0x0f01: eth0,eth1,eth2,eth3,eth4 Chip WAN Only Ports 0001, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0001:eth0 Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000: Chip LAN Only Ports 0f00, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0f00:eth1,eth2,eth3,eth4 WAN/LAN Both Capable Ports 0x0000: Created Ethernet Rx queue 4 with size 512, Descriptor base=00c1e000 Created Ethernet Rx queue 3 with size 512, Descriptor base=00c21000 ===> Activate Deep Green Mode Initialized Runner Host Layer Initialized Runner Unicast Layer Initialized Runner L2 Unicast Layer Initialized Runner Multicast Layer [0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.[0m Enabled Runner binding to Flow Cache Initialized Runner Protocol Layer (700) Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009> NComm TMS V6.90 Kernel Module loaded. Broadcom 802.1Q VLAN Interface, v0.1 brcm_otp_init entry Initializing WLCSM Module WLCSM Module loaded successfully [1m[34mWifi Forwarding Driver is initialized![0m gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver PPTP driver version 0.8.5 DHD_FKB_POOL size is:1280 and entry size:2016 fkbpool address range: d8400000 <-> d8676000 DHD_PKTTAG POOL size is:1280 and entry size:64 dhd_module_init in dhd_queue_budget = 256 dhd_sta_threshold = 2048 dhd_if_threshold = 65536 no wifi platform data, skip PCI_PROBE: bus 1, slot 0,vendor 14E4, device AA52(good PCI location) dhdpcie_init: can't find adapter info for this chip pcieh 0000:01:00.0: enabling device (0140 -> 0142) DHD: dongle ram size is set to 983040(orig 983040) at 0x180000 dhd:0: fw path:(null) nv path:(null) dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024 dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 TX wakeup info: reg = <0x80299004>, val = <0x10000000> RX wakeup info: reg = <0x8029a004>, val = <0x28000000> dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0) dhd_attach(): thread:dhd_watchdog_thread:227 started dhd_attach(): thread:dhd0_dpc:228 started dhd_deferred_work_init: work queue initialized dhd_macdbg_attach: psvmpmems d8e0ec80 svmpmems_sz 13 Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf4f2768 Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf4f2784 [1m[34m wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3[0m Instantiating WFD 0 thread dhd:0: fw path:(null) nv path:(null) dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path= update_firmware_path: pfw_path = /etc/wlan/dhd _dhdpcie_get_nvram_params: fail to read nvram from flash. dhdpcie_ramsize_adj: Enter dhd_bea_read_header: Not a .bea header dhdpcie_download_code_file: download firmware /etc/wlan/dhd/43602a3/rtecdc.bin dhd_bea_read_header: Not a .bea header wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl: ID=pci/0/1/0/ wl: ID=pci/0/1/0/ wl: loading /etc/wlan/bcm43602_map.bin wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19 wl: reading /etc/wlan/bcm43602_nvramvars.bin, file size=15 dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. PCIe shared addr (0x001b8ef8) read took 36023 usec before dongle is ready DMA RX offset from shared Area 0 dhdpcie_readshared: Dongle advertizes 2 size indices dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it H2D DMA WR INDX : array size 384 = 2 * 190 D2H DMA RD INDX : array size 32 = 2 * 3 D2H DMA WR INDX : array size 32 = 2 * 3 H2D DMA RD INDX : array size 384 = 2 * 190 ring_info_raw: 56 1c 9f 26 00 2c ab 26 00 a8 ac 26 00 24 ae 26 00 2a ae 26 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 be 00 00 00 dhdpcie_readshared: max H2D queues 190 dhd_bus_start: Initializing 190 h2drings dhd_runner_flowmgr_init: dhd0_rnr bootmem addr<cba00000> size<14680064> dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512 dhd_runner_policy_init: N+M Policy = 0 1 (HW) dhd_bus_cmn_writeshared: 0000: 00 a0 77 1f 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 80 d9 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 e0 a9 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 40 d9 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 dc 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 00 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 10 14 00 dhd_bus_cmn_writeshared: 0000: 00 08 aa 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 0c aa 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 aa 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 04 aa 18 00 00 00 00 Attach flowrings pool for 188 rings [0;33;40mRunner DHD PCIE: vendor<0x14e4> device<0xaa52> bus<1> slot<0>[0m Initial configuration ================================= rx_post_flow_ring_base_addr : c0d98000 tx_post_flow_ring_base_addr : cb9c4000 rx_complete_flow_ring_base_addr : c0dc0000 tx_complete_flow_ring_base_addr : c0d94000 r2d_wr_arr_base_addr : e12a1000 d2r_rd_arr_base_addr : e12a1402 r2d_rd_arr_base_addr : e12a1c00 d2r_wr_arr_base_addr : e12a1802 tx_post_mgmt_arr_base_addr : e12a2000 tx_post_mgmt_arr_base_phys_addr : 0x18aa1000 r2d_wr_arr_base_phys_addr : 0x18aa0000 d2r_rd_arr_base_phys_addr : 0x18aa0402 r2d_rd_arr_base_phys_addr : 0x18aa0c00 d2r_wr_arr_base_phys_addr : 0x18aa0802 Doorbell ISR : bf527728 Doorbell CTX : d886e800 Creating CPU ring for queue number 7 with 128 packets descriptor=0xbf2bf21c, size_of_entry 16 Done initializing Ring 7 Base=0xe0833000 End=0xe0833800 calculated entries= 128 RDD Base=c2f000K descriptor=0xbf2bf21c [0;33;40mRunner DHD Offload initialization complete[0m CUR_ETHERADDR : 6 00 90 4c 17 20 00 dhd_sync_with_dongle: GET_REVINFO device 0x43bb, vendor 0x14e4, chipnum 0xaa52 Dongle Host Driver, version 7.14.170.36.cpe5.02L03.0-kdb wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0 PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location) dhdpcie_init: can't find adapter info for this chip pcieh 0001:01:00.0: enabling device (0140 -> 0142) DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000 dhd:1: fw path:(null) nv path:(null) dhd_runner_attach: Tx Offload - Enabled, Ring Size = 1024 dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 TX wakeup info: reg = <0x80299004>, val = <0x11000000> RX wakeup info: reg = <0x8029a004>, val = <0x29000000> dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0) dhd_attach(): thread:dhd_watchdog_thread:22d started dhd_attach(): thread:dhd1_dpc:22e started dhd_deferred_work_init: work queue initialized dhd_macdbg_attach: psvmpmems d88f4a80 svmpmems_sz 13 Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf4f27a0 Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf4f27bc [1m[34m wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type fkb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc[0m Instantiating WFD 1 thread dhd:1: fw path:(null) nv path:(null) dhd_bus_download_firmware: firmware path=/etc/wlan/dhd, nvram path= update_firmware_path: pfw_path = /etc/wlan/dhd _dhdpcie_get_nvram_params: fail to read nvram from flash. dhdpcie_ramsize_adj: Enter dhd_bea_read_header: Not a .bea header dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000 dhdpcie_download_code_file: download firmware /etc/wlan/dhd/4366c0/rtecdc.bin dhd_bea_read_header: Not a .bea header wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl: ID=pci/1/1/0/ wl: ID=pci/1/1/0/ wl: loading /etc/wlan/bcm43664_map.bin wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19 wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=149 dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. PCIe shared addr (0x002aed54) read took 69023 usec before dongle is ready DMA RX offset from shared Area 0 dhdpcie_readshared: Dongle advertizes 2 size indices dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it H2D DMA WR INDX : array size 544 = 2 * 266 D2H DMA RD INDX : array size 32 = 2 * 3 D2H DMA WR INDX : array size 32 = 2 * 3 H2D DMA RD INDX : array size 544 = 2 * 266 ring_info_raw: 56 18 61 43 00 e8 71 43 00 fc 73 43 00 10 76 43 00 16 76 43 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00 dhdpcie_readshared: max H2D queues 266 dhd_bus_start: Initializing 266 h2drings dhd_runner_flowmgr_init: dhd1_rnr bootmem addr<cac00000> size<14680064> dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512 dhd_runner_policy_init: N+M Policy = 0 1 (HW) dhd_bus_cmn_writeshared: 0000: 00 70 14 1a 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 80 dc 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 20 b2 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 dd 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 80 dd 00 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 20 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 10 14 00 dhd_bus_cmn_writeshared: 0000: 00 48 b2 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 4c b2 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 40 b2 18 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 44 b2 18 00 00 00 00 Attach flowrings pool for 264 rings [0;33;40mRunner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0>[0m Initial configuration ================================= rx_post_flow_ring_base_addr : c0dc8000 tx_post_flow_ring_base_addr : cabc4000 rx_complete_flow_ring_base_addr : c0dd8000 tx_complete_flow_ring_base_addr : c0dd0000 r2d_wr_arr_base_addr : e12c9000 d2r_rd_arr_base_addr : e12c9402 r2d_rd_arr_base_addr : e12c9c00 d2r_wr_arr_base_addr : e12c9802 tx_post_mgmt_arr_base_addr : e12ca000 tx_post_mgmt_arr_base_phys_addr : 0x18b25000 r2d_wr_arr_base_phys_addr : 0x18b24000 d2r_rd_arr_base_phys_addr : 0x18b24402 r2d_rd_arr_base_phys_addr : 0x18b24c00 d2r_wr_arr_base_phys_addr : 0x18b24802 Doorbell ISR : bf527728 Doorbell CTX : d88eca00 Creating CPU ring for queue number 1 with 128 packets descriptor=0xbf2bf024, size_of_entry 16 Done initializing Ring 1 Base=0xe0841000 End=0xe0841800 calculated entries= 128 RDD Base=c3d000K descriptor=0xbf2bf024 [0;33;40mRunner DHD Offload initialization complete[0m dhd_rx_frame: net device is NOT registered. drop event packet dhd_rx_frame: net device is NOT registered. drop event packet CUR_ETHERADDR : 6 00 90 4c 1d 00 00 dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90 Dongle Host Driver, version 7.14.170.36.cpe5.02L03.0-kdb wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1 dhd_module_init out RDPA DS WAN UDP Filter Command Driver Broadcom Ingress QoS Module Char Driver v0.1 Registered<3003>[0m Broadcom Ingress QoS ver 0.1 initialized [0;36m[DSPHAL] [0mdsphal_init: Starting DSPHAL driver. [0;35m[DSPHAL] [0mpcm_clk_init: starting PCM clock [0;35m[DSPHAL] [0mpcm_nco_mux_cfg: using MISC for NCO FCW [0;36m[DSPHAL] [0mpcm_nco_init: PCM clock in ZSI mode [0;35m[DSPHAL] [0mdh_configure_channel: device 0, channel 0, id 0, devType 40, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 4 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 5 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 4 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 5 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0 [0;35m[DSPHAL] [0mdh_configure_channel: device 0, channel 1, id 1, devType 40, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 4 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 5 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 4 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1 [0;35m[DSPHAL] [0mpcm_ts_alloc: DMA 5 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1 [0;36m[SLICSLAC] [0mslicslac_init: Starting SLIC/SLAC driver. sc_sfp 0-0050: initialized sc_sfp 0-0051: initialized I2C SFP Module Driver Loaded Ethernet Auto Power Down and Sleep: Enabled Energy Efficient Ethernet: Enabled echo (605): drop_caches: 3

Technicolor THG3000

Please note THG3000 version runs Homeware firmware (custom OpenWrt) by Technicolor.

---- BTRM V1.6 PMCS AFEL PWRZ MEML PMCD MEMP CODE ZBSS MAIN CACH OTP? OTPP ROTB SCBT NAND IMG? IMGL HDR? HDRP MCV? KEY? KEYA MID? MIDP MCVA SBI? SBIA PASS ---- HELO CPU0 PMCM PMCS PMCD CODE L1CD MMUI ZBBS MAIN 4.1603-1.0.38-116.174 DRAM NVRAM memcfg 0x427 MCB chksum 0xf67f5b05 DDR3-1600 CL11 512MB MemsysInit lpe2_custom 0p10 20140709 DDR3 807120CC 80003000 00000070 016028BC MCB rev=0x00020201 Ref ID=0x028BC Sub Bld=0x016 ZQ Cal LP PHY p_term=0x06 n_term=0x06 p_drive=0x10 n_drive=0x10 PLL Ref(Hz)=0x02FAF080 UI STEPS=0x04C DDR CLK(MHz)=0x31F WL CLK dly(ps)=0x0C8 bitT(ps)=0x271 VDLsize(fs)=0x201F CLK_VDL=0x020 Changed Byte Lane LDE Changed Byte Lane LDE Add/Ctl Alignment no adjustment memsys_init call phy init returns 0x00000000 MEMC init size 2 clock 6 MemsysInit lpe2_custom 0p10 20140709 DDR3 807120CC 80003000 000003E0 016028BC MCB rev=0x00020201 Ref ID=0x028BC Sub Bld=0x016 SHMOO 28nm 0p9 20140709 80003000 80002500 00000000 00020000 00000000 ROSC Auto clk counter start Found inflection point ROSC final result: nRing Osc Meas check rosc 0x00 = 0x0000009C clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x01 = 0x000000B4 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x02 = 0x000000A7 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x03 = 0x000000F1 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x04 = 0x000000DF clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x05 = 0x000000FE clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x06 = 0x00000084 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x07 = 0x00000053 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x08 = 0x000000BD clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x09 = 0x000000AA clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x0A = 0x00000082 clk_count = 0x000004F9 scb_clk = 0x0064 MHz rosc 0x0B = 0x000000A9 clk_count = 0x000004F9 scb_clk = 0x0064 MHz ROSC Auto clk counter finished One UI Steps : 0x57 Shmoo WL 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 S--------------------------X+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 01 S--------------------X+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Using passive Rd Data Delay SET RD DATA DELAY 0x800034B0 = 0x00000006 SET RD DATA DELAY 0x800036B0 = 0x00000006 Shmoo RD En Initial: WL Cyc=0x0 ODT Delay=0x0 ODT PreLen=0x2 Post: WL Cyc=0x0 ODT Delay=0x0 ODT PreLen=0x2 Initial: WL Cyc=0x0 ODT Delay=0x0 ODT PreLen=0x2 Post: WL Cyc=0x0 ODT Delay=0x0 ODT PreLen=0x2 B0 RISE UI=1 VDL=1E PICK UI=2 VDL=1E B1 RISE UI=1 VDL=23 PICK UI=2 VDL=23 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 --S---------------------------X++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 01 --S--------------------------------X+++++++++++++++++++++++++++++++++++++++++++++++++++ Rd Dat Dly 6 ++ 5 ++ 4 ++ 3 ++ 2 -- Converged RD-DAT-DLY = 2 BL0 Final RD-DAT-DLY = 4 BL1 Final RD-DAT-DLY = 4 Shmoo RD DQ NP DQS : B0 VDL=4D ok B1 VDL=4C ok 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 --------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------- 01 ---------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------- 02 ------------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++------------ 03 ---------------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----- 04 --++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------------- 05 ----------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++--- 06 ----------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----------- 07 ---------------------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++ 08 --------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++-------------- 09 ---------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++-------- 10 ------------++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++------------- 11 ----------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------ 12 -------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++--------- 13 ---------------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++--------- 14 ------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++----------- 15 ----------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------- Shmoo RD DQ P 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 -------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++------------ 01 -------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++------ 02 ----------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------------- 03 ---------------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----- 04 ++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++------------------ 05 ---------------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++--- 06 ----------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++---------- 07 --------------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++ 08 --------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++-------------- 09 --------------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------- 10 --------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------ 11 --------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----- 12 -----------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++--------- 13 --------------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------- 14 ----------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----------- 15 --------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----- Shmoo RD DQ N 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 --------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------- 01 ---------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------- 02 ------------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++------------ 03 ---------------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++--- 04 --++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------------- 05 ----------------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++--- 06 ----------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----------- 07 ---------------------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++ 08 ---------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------------- 09 ----------------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++-------- 10 -----------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++------------- 11 ----------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------ 12 -------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++--------- 13 ---------------+++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++--------- 14 ------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++----------- 15 ----------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------- Shmoo WR DQ 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 --------++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++--------- 01 --------------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++---- 02 ----------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++-------- 03 ----------------++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++- 04 ---++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------------ 05 ------------------++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++--- 06 ------------++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++---------- 07 -----------------------+++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++ 08 --++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------------- 09 -------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----------- 10 ---++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++------------------- 11 -------++++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----------- 12 ----++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++----------------- 13 ------+++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++-------------- 14 ---++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++------------------ 15 --------+++++++++++++++++++++++++++++++++X++++++++++++++++++++++++++++++++++----------- Shmoo WR DM WR DM 000000000011111111112222222222333333333344444444445555555555666666666677777777778888888 012345678901234567890123456789012345678901234567890123456789012345678901234567890123456 00 ---------+++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++------- 01 -++++++++++++++++++++++++++++++++++++++X+++++++++++++++++++++++++++++++++++++++-------- memsys_init call shmoo returns 0x00000000 PASS Technicolor Gateway (c) 2019, All rights reserved Gateway initialization sequence started Status wait timeout: nandsts=0x30000000 mask=0x40000000, count=0 Boot Loader Version : 19.02.1146-0000000-20190110090550-897d2844f012557134a272eb8a8a90f85e9a7a8d Boot Loader OID : 5c3707ae5427bc3aef0bdfd7 CPU : BCM63136B0 RAM : 512MB Flash : 250MB NAND Board Mnemonic : VCNT-I Market ID : FFFC Variant ID : VU Booting : Bank 1 SW Version : 17.4.c.0277-2441004-20190521105542-f0ed0605a553eadb7abd132d4728c288c52e2d9d Starting the Linux kernel Enabling watchdog Code Address: 0x00008000, Entry Address: 0x00008000 Decompression OK! Entry at 0x00008000 Closing network. Starting program at 0x00008000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 4.1.38 (repowrt-builder@0e3f98211bf6) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 unknown) ) #1 SMP PREEMPT Tue Apr 9 00:48:46 UTC 2019 [ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: BCM963138 [ 0.000000] Prozone memory from command line 1ffe0000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x1ff00000 to virtual address at 0xdff00000 with size of 0x100000 byte for TCH_RESERVED [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0fd00000 to virtual address at 0xcfd00000 with size of 0x300000 byte for adsl [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0d000000 to virtual address at 0xcd000000 with size of 0x2c00000 byte for tm [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0cc00000 to virtual address at 0xccc00000 with size of 0x400000 byte for mc [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0c000000 to virtual address at 0xcc000000 with size of 0xb00000 byte for dhd0 [ 0.000000] creating a MT_MEMORY_NONCACHED device at physical address of 0x0b200000 to virtual address at 0xcb200000 with size of 0xe00000 byte for dhd1 [ 0.000000] On node 0 totalpages: 111360 [ 0.000000] free_area_init_node: node 0, pgdat c050be60, node_mem_map dfa75000 [ 0.000000] DMA zone: 36 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4096 pages, LIFO batch:0 [ 0.000000] Normal zone: 1116 pages used for memmap [ 0.000000] Normal zone: 107264 pages, LIFO batch:31 [ 0.000000] pmc_init:PMC using DQM mode [ 0.000000] pmc_init:fcbf 3650362 4b004b [ 0.000000] PERCPU: Embedded 11 pages/cpu @dfa4f000 s15392 r8192 d21472 u45056 [ 0.000000] pcpu-alloc: s15392 r8192 d21472 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 110208 [ 0.000000] Kernel command line: console=ttyS0,115200 irqaffinity=0 debug root=/dev/mtdblock1 rootfstype=squashfs tbbt_addr=0xfaa0000 btab=0xa080c btab_bootid=1 bl_version=19.02.1146-0000000-20190110090550-897d2844f012557134a272eb8a8a90f85e9a7a8d board=VCNT-I platform.prozone_addr=0x1ffe0000 bl_oid=5c3707ae5427bc3aef0bdfd7 .r2secr=0x1ffdf000 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 435232K/445440K available (3801K kernel code, 231K rwdata, 1080K rodata, 188K init, 309K bss, 10208K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbec00000 - 0xbfe00000 ( 18 MB) [ 0.000000] .text : 0xc0008000 - 0xc04cc9d4 (4883 kB) [ 0.000000] .init : 0xc04cd000 - 0xc04fc000 ( 188 kB) [ 0.000000] .data : 0xc04fc000 - 0xc0535e50 ( 232 kB) [ 0.000000] .bss : 0xc0535e50 - 0xc05834c4 ( 310 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] Cortex A9 MPCORE GIC init [ 0.000000] DIST at fc01f000, CPU_IF at fc01e100 [ 0.000000] L2C: DT/platform modifies aux control register: 0x02070000 -> 0x6a450000 [ 0.000000] L2C: DT/platform tries to modify or specify cache size [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 I prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 512 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x6e450001 [ 0.000000] L2C: failed to init: -19 [ 0.000000] map_hw_timer_interrupt,127: interrupt_id 96 [ 0.000000] map_hw_timer_interrupt,127: interrupt_id 97 [ 0.000000] map_hw_timer_interrupt,127: interrupt_id 98 [ 0.000000] map_hw_timer_interrupt,127: interrupt_id 99 [ 0.000000] clocksource timer_cs: mask: 0x3fffffff max_cycles: 0x3fffffff, max_idle_ns: 9556302227 ns [ 0.000000] sched_clock: 32 bits at 1kHz, resolution 1000000ns, wraps every 2147483647500000ns [ 0.052000] console [ttyS0] enabled [ 0.053000] Calibrating delay loop... 1990.65 BogoMIPS (lpj=995328) [ 0.062000] pid_max: default: 32768 minimum: 301 [ 0.064000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.065000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.067000] --Kernel Config-- [ 0.068000] SMP=1 [ 0.069000] PREEMPT=1 [ 0.070000] DEBUG_SPINLOCK=0 [ 0.071000] DEBUG_MUTEXES=0 [ 0.073000] Initializing cgroup subsys blkio [ 0.074000] Initializing cgroup subsys memory [ 0.075000] Initializing cgroup subsys debug [ 0.076000] CPU: Testing write buffer coherency: ok [ 0.078000] Broadcom Logger v0.1 [ 0.093000] Setting up static identity map for 0x8220 - 0x8254 [ 0.109000] Brought up 2 CPUs [ 0.110000] SMP: Total of 2 processors activated (3981.31 BogoMIPS). [ 0.111000] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x1f) [ 0.112000] CPU: This may indicate a broken bootloader or firmware. [ 0.116000] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.117000] NET: Registered protocol family 16 [ 0.119000] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.125000] cpuidle: using governor ladder [ 0.131000] cpuidle: using governor menu [ 0.148000] SCSI subsystem initialized [ 0.149000] usbcore: registered new interface driver usbfs [ 0.150000] usbcore: registered new interface driver hub [ 0.151000] usbcore: registered new device driver usb [ 0.152000] bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated [ 0.153000] skb_free_task created successfully [ 0.154000] gbpm_do_work scheduled [ 0.154000] BLOG v3.0 Initialized [ 0.157000] BLOG Rule v1.0 Initialized [ 0.157000] Broadcom IQoS v0.1 initialized [ 0.157000] Broadcom GBPM v0.1 initialized [ 0.157000] NET: Registered protocol family 8 [ 0.157000] NET: Registered protocol family 20 [ 0.183000] Switched to clocksource timer_cs [ 0.185000] NET: Registered protocol family 2 [ 0.186000] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.187000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.188000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.189000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.190000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.191000] NET: Registered protocol family 1 [ 0.192000] PCI: CLS 0 bytes, default 32 [ 0.194000] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.196000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.197000] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.198000] fuse init (API version 7.23) [ 0.200000] io scheduler noop registered (default) [ 0.202000] Broadcom NAND controller (BrcmNand Controller) [ 0.203000] mtd->oobsize=0, mtd->eccOobSize=0 [ 0.203000] NAND_CS_NAND_XOR=00000000 [ 0.204000] Disabling XOR: Before: SEL=40000001, XOR=00000000 [ 0.205000] Disabling XOR: After: SEL=40000000, XOR=00000000 [ 0.206000] B4: NandSelect=40000000, nandConfig=26152300, chipSelect=0 [ 0.207000] brcmnand_read_id: CS0: dev_id=2cda9095 [ 0.208000] After: NandSelect=00000000, nandConfig=26152300 [ 0.209000] Block size=00020000, erase shift=17 [ 0.210000] NAND Config: Reg=26152300, chipSize=256 MB, blockSize=128K, erase_shift=11 [ 0.211000] busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff [ 0.212000] BrcmNAND mfg 2c da MICRON MT29F2G08ABA 256MB on CS0 [ 0.213000] [ 0.213000] Found NAND on CS0: ACC=c388001b, cfg=26152300, flashId=2cda9095, tim1=65324458, tim2=80000e54 [ 0.214000] BrcmNAND version = 0x80000700 256MB @00000000 [ 0.215000] brcmnand_scan: B4 nand_select = 00000000 [ 0.216000] brcmnand_scan: After nand_select = 00000000 [ 0.217000] handle_acc_control: default CORR ERR threshold 6 bits [ 0.218000] ACC: 27 OOB bytes per 512B ECC step; from ID probe: 16 [ 0.219000] Use strap setting for ecc size 27 bytes, mtd->oobsize 108. [ 0.220000] page_shift=11, bbt_erase_shift=17, chip_shift=28, phys_erase_shift=17 [ 0.221000] Brcm NAND controller version = 7.0 NAND flash size 256MB @10000000 [ 0.222000] ECC layout=brcmnand_oob_bch8_27_2k [ 0.223000] brcmnand_scan: mtd->oobsize=108 [ 0.224000] brcmnand_scan: oobavail=51, eccsize=512, writesize=2048 [ 0.225000] brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=8, eccbytes=14 [ 0.227000] Gateway flash mapping [ 0.228000] brcmnand_reset_corr_threshold: default CORR ERR threshold 6 bits for CS0 [ 0.229000] [NAND] : tBBT loaded [ 0.230000] Technicolor nand flash translation layer initialized. [ 0.231000] flash mapping initialized, size=250 Mb [ 0.232000] parse_btab: num_banks (5) [ 0.233000] Creating 1 MTD partitions on "technicolor-nand-tl": [ 0.233000] 0x000005c00000-0x000008860000 : "rootfs" [ 0.234000] Creating 5 MTD partitions on "technicolor-nand-tl": [ 0.235000] 0x0000000e0000-0x000005a00000 : "rootfs_data" [ 0.236000] 0x000005a00000-0x00000aa00000 : "bank_1" [ 0.238000] 0x00000aa00000-0x00000fa00000 : "bank_2" [ 0.240000] 0x000000080000-0x0000000a0000 : "eripv2" [ 0.241000] 0x0000000a0000-0x0000000e0000 : "rawstorage" [ 0.243000] PPP generic driver version 2.4.2 [ 0.244000] PPP BSD Compression module registered [ 0.245000] PPP Deflate Compression module registered [ 0.246000] NET: Registered protocol family 24 [ 0.247000] brcmboard registered [ 0.248000] brcmboard: brcm_board_init entry [ 0.249000] print_rst_status: Last RESET due to POR reset [ 0.276000] DYING GASP IRQ Initialized and Enabled [ 0.277000] Serial: BCM63XX driver $Revision: 3.00 $ [ 0.278000] Magic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands) [ 0.279000] ttyS0 at MMIO 0xfffe8600 (irq = 64, base_baud = 921600) is a BCM63XX [ 0.280000] ttyS1 at MMIO 0xfffe8620 (irq = 65, base_baud = 921600) is a BCM63XX [ 0.281000] BPM: tot_mem_size=536870912B (512MB), buf_mem_size <20%> =107374180B (102MB), num of buffers=41425, buf size=2592 [ 0.283000] Broadcom BPM Module Char Driver v0.1 Registered<3004> [ 0.285000] PCIe HCD (impl1) [ 0.299000] bcm963xx-pcie: found core [0] Rev [3.01] with 1 Lanes [ 0.879000] bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00 [ 0.880000] pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff] [ 0.881000] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.882000] pci 0000:00:00.0: [14e4:6313] type 01 class 0x060400 [ 0.883000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.884000] PCI: bus0: Fast back to back transfers disabled [ 0.884000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.885000] pci 0000:01:00.0: [14e4:aa52] type 00 class 0x028000 [ 0.886000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 0.887000] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit] [ 0.888000] pci 0000:01:00.0: supports D1 D2 [ 0.889000] pci 0000:00:00.0: Checking PCIe ASPM for vendor 14e4 device aa52 [ 0.890000] pci 0000:00:00.0: Disabling PCIe ASPM for vendor 14e4 device aa52 [ 0.891000] PCI: bus1: Fast back to back transfers disabled [ 0.892000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.892000] pci 0000:00:00.0: BAR 8: assigned [mem 0x90000000-0x905fffff] [ 0.892000] pci 0000:01:00.0: BAR 2: assigned [mem 0x90000000-0x903fffff 64bit] [ 0.893000] pci 0000:01:00.0: BAR 0: assigned [mem 0x90400000-0x90407fff 64bit] [ 0.893000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.894000] pci 0000:00:00.0: bridge window [mem 0x90000000-0x905fffff] [ 0.895000] pcieport 0000:00:00.0: enabling device (0140 -> 0142) [ 0.896000] pcieport 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 0.897000] pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 0.910000] bcm963xx-pcie: found core [1] Rev [3.01] with 1 Lanes [ 1.489000] bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00 [ 1.490000] pci_bus 0001:00: root bus resource [mem 0xa0000000-0xafffffff] [ 1.491000] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.492000] pci 0001:00:00.0: [14e4:6313] type 01 class 0x060400 [ 1.493000] pci 0001:00:00.0: PME# supported from D0 D3hot [ 1.494000] PCI: bus0: Fast back to back transfers disabled [ 1.495000] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.496000] pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000 [ 1.497000] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 1.497000] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit] [ 1.498000] pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref] [ 1.499000] pci 0001:01:00.0: supports D1 D2 [ 1.500000] pci 0001:00:00.0: Checking PCIe ASPM for vendor 14e4 device 4365 [ 1.501000] pci 0001:00:00.0: Disabling PCIe ASPM for vendor 14e4 device 4365 [ 1.502000] PCI: bus1: Fast back to back transfers disabled [ 1.503000] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.503000] pci 0001:00:00.0: BAR 8: assigned [mem 0xa0000000-0xa0bfffff] [ 1.503000] pci 0001:00:00.0: BAR 9: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.503000] pci 0001:01:00.0: BAR 2: assigned [mem 0xa0000000-0xa07fffff 64bit] [ 1.504000] pci 0001:01:00.0: BAR 4: assigned [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.505000] pci 0001:01:00.0: BAR 0: assigned [mem 0xa0800000-0xa0807fff 64bit] [ 1.505000] pci 0001:00:00.0: PCI bridge to [bus 01] [ 1.506000] pci 0001:00:00.0: bridge window [mem 0xa0000000-0xa0bfffff] [ 1.507000] pci 0001:00:00.0: bridge window [mem 0xa0c00000-0xa0cfffff 64bit pref] [ 1.508000] pcieport 0001:00:00.0: enabling device (0140 -> 0142) [ 1.509000] pcieport 0001:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 1.510000] pci 0001:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 1.511000] GACT probability NOT on [ 1.512000] Mirror/redirect action on [ 1.513000] u32 classifier [ 1.514000] input device check on [ 1.515000] Actions configured [ 1.516000] NET: Registered protocol family 10 [ 1.517000] sit: IPv6 over IPv4 tunneling driver [ 1.518000] NET: Registered protocol family 17 [ 1.519000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.520000] Bridge firewalling registered [ 1.521000] Ebtables v2.0 registered [ 1.522000] ebt_time registered [ 1.523000] ebt_ftos registered [ 1.523000] 8021q: 802.1Q VLAN Support v1.8 [ 1.524000] Registering SWP/SWPB emulation handler [ 1.539000] VFS: Mounted root (squashfs filesystem) readonly on device 31:1. [ 1.540000] Freeing unused kernel memory: 188K (c04cd000 - c04fc000) open: No such file or directory open: No such file or directory [ 2.561000] init: Console is alive [ 3.697000] random: nonblocking pool is initialized [ 4.484000] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.527000] Button Hotplug driver version 0.4.1 [ 4.549000] usbcore: registered new interface driver usb-storage [ 4.556000] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.573000] init: - preinit - [ 6.390000] jffs2: notice: (58) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. switching to overlay [ 6.430000] insmod: module is already loaded - bankmgr removing unnecessary files from inactive bank bank_2 HOMEWARE_CONFIG_ON_ACTIVE_BANK mounting overlay fs open: No such file or directory 1+0 records in 1+0 records out [ 7.047000] tommath: module license 'unspecified' taints kernel. [ 7.048000] Disabling lock debugging due to kernel taint [ 7.062000] brcm_otp_init entry [ 7.096000] eRIPv2 secrets passed correctly to Linux [ 7.133000] Dsl Annex A board [ 7.134000] Set board (VCNT-I) [ 7.465000] procd: - early - [ 8.049000] procd: - watchdog - [ 8.051000] procd: - ubus - [ 8.215000] procd: - init - [ 8.441000] jffs2: notice: (178) check_node_data: wrong data CRC in data node at 0x02c07040: read 0x379c655c, calculated 0xef777248. [ 8.616000] jffs2: notice: (178) check_node_data: wrong data CRC in data node at 0x02fe30f4: read 0xed7867a5, calculated 0xf973b3cc. [ 9.653000] tm_base_addr 0xcd000000, size 46137344, tm_base_addr_phys 0x0d000000 [ 9.654000] mc_base_addr 0xccc00000, size 4194304, mc_base_addr_phys 0x0cc00000 [ 9.655000] [ 9.655000] RDP TM memory = 44MB, MC memory = 4MB : Max Possible Bufs <15018> of size <2560>; Allocating <7680> bufs; RDP enum <2> [ 9.656000] WARNING!RDP reserved memories are wasting 21MB of memory, please adjust your reserved memory size [ 9.664000] ++++Runner gso_desc_pool created successfully [ 9.676000] RDPA DS WAN UDP Filter Command Driver [ 9.906000] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.937000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0 [ 9.952000] Initializing XFRM netlink socket [ 9.958000] NET: Registered protocol family 15 [ 9.964000] ipip: IPv4 over IPv4 tunneling driver [ 9.992000] L2TP core: blog_l2tp_rcv_check [ 9.997000] l2tp_core: L2TP core driver, V2.0 [ 10.003000] l2tp_netlink: L2TP netlink interface [ 10.007000] nat46: module (version 683fbd2b765506332a1af141545652bf58f03166) loaded. [ 10.016000] gre: GRE over IPv4 demultiplexor driver [ 10.022000] ip_gre: GRE over IPv4 tunneling driver [ 10.030000] ip6_gre: GRE over IPv6 tunneling driver [ 10.037000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.055000] ncr_master_key_set_internal [ 10.059000] ncr: driver 0.2-mr1 loaded. [ 10.065000] Netfilter messages via NETLINK v0.30. [ 10.076000] ip_set: protocol 6 [ 10.106000] brcmchipinfo: brcm_chipinfo_init entry [ 10.113000] bcmxtmrt: Broadcom BCM3136B0 ATM/PTM Network Device v0.9 [ 10.120000] Created XTM Rx queue 5 with size 256,Descriptor base=00c09000 [ 10.127000] Created XTM Rx queue 6 with size 256,Descriptor base=00c0b000 [ 10.163000] OSCK Loaded! [ 10.186000] Client Private Key Loaded! [ 10.195000] Broadcom Ingress QoS Module Char Driver v0.1 Registered<3003> [ 10.202000] iq_drv_construct rdpa_cpu_get returned error [ 10.208000] [ 10.208000] Broadcom Ingress QoS ver 0.1 initialized [ 10.221000] i2c /dev entries driver [ 10.230000] NBUFF v1.0 Initialized [ 10.246000] Total # of labels = 63 [ 10.250000] Initialized fcache state [ 10.255000] Broadcom Packet Flow Cache Char Driver v4.0 Registered<3002> [ 10.263000] Created Proc FS /procfs/fcache [ 10.267000] Broadcom Packet Flow Cache registered with netdev chain [ 10.275000] Broadcom Packet Flow Cache learning via BLOG enabled. [ 10.283000] [FHW] pktDbgLvl[0xbf178124]=0 [ 10.288000] [FHW] fhw_construct: [ 10.292000] Initialized Fcache HW accelerator layer state [ 10.299000] flwStatsThread created. numFlwsPerPoll 546 maxFlwIdx 16383 [ 10.306000] Constructed Broadcom Packet Flow Cache v4.0 [ 10.316000] Initialized Runner Host Layer [ 10.319000] Initialized Runner Unicast Layer [ 10.324000] Initialized Runner L2 Unicast Layer [ 10.328000] Initialized Runner Multicast Layer [ 10.334000] Broadcom Packet Flow Cache HW acceleration enabled. [ 10.342000] Enabled Runner binding to Flow Cache [ 10.354000] Initialized Runner Protocol Layer (700) [ 10.358000] Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009> [ 10.370000] Runner Port#0 (Internal MUX Port#2) connects to Crossbar Port#1 [ 10.377000] Switch Port#3 (Internal MUX Port#0) connects to Crossbar Port#4 [ 10.384000] Unused MUX Internal Port#1 connects to Crossbar External Port#0 [ 10.391000] Cross Bar MUX Config : Internal Port 00 maps to External Port 04 <reg_val : 0x0000000c> [ 10.401000] Cross Bar MUX Config : Internal Port 01 maps to External Port 00 <reg_val : 0x00000004> [ 10.410000] Cross Bar MUX Config : Internal Port 02 maps to External Port 01 <reg_val : 0x00000044> [ 10.419000] Broadcom BCM63136_B0 Ethernet Network Device v0.1 [ 10.426000] dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered [ 10.433000] eth0: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008:0x08:Internal PHY> MAC:20:B0:01:8C:65:28 [ 10.443000] eth1: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009:0x09:Internal PHY> MAC:20:B0:01:8C:65:28 [ 10.454000] eth2: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a:0x0a:Internal PHY> MAC:20:B0:01:8C:65:28 [ 10.464000] eth3: <Ext sw port: 3> <Logical : 11> MAC : 20:B0:01:8C:65:28 [ 10.471000] Chip Physical Port 13, Cross Bar Port 4, PHY_ID <0x0007f00b:0x0b:Internal PHY > [ 10.480000] ++++ disabling GSO on logical_port=0 dev=eth4 [ 10.486000] eth4: <Int sw port: 0> <Logical : 00> MAC : 20:B0:01:8C:65:28 [ 10.492000] Chip Physical Port 10, Cross Bar Port 1, PHY_ID <0x0007f04c:0x0c:Internal PHY > [ 10.502000] Ethernet Auto Power Down and Sleep: Enabled [ 10.507000] Cross bar port 1 of Int switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 10.516000] Ext switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 10.524000] Ext switch port 1; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 10.531000] Ext switch port 2; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 10.538000] Cross bar port 4 of Ext switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00 [ 10.549000] All Port Bit Map: 0x0f01: eth4,eth0,eth1,eth2,eth3 [ 10.554000] Chip WAN Only Ports 0001, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0001:eth4 [ 10.564000] Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000: [ 10.574000] Chip LAN Only Ports 0f00, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0f00:eth0,eth1,eth2,eth3 [ 10.585000] WAN/LAN Both Capable Ports 0x0000: [ 10.591000] Created Ethernet Rx queue 4 with size 512, Descriptor base=00c0e000 [ 10.598000] Created Ethernet Rx queue 3 with size 512, Descriptor base=00c11000 [ 10.606000] ===> Activate Deep Green Mode [ 10.614000] Wifi Forwarding Driver is initialized! [ 10.660000] Initializing WLCSM Module [ 10.663000] WLCSM Module loaded successfully [ 11.473000] --SMP support [ 11.474000] wl: dsl_tx_pkt_flush_len=338 [ 11.474000] wl: norm_wmark_tot=26926, pktc_wmark_tot=26926 [ 11.475000] Dongle chip:0xaa52 quit wl.ko to be loaded with DHD. [ 11.476000] Dongle chip:0x4365 quit wl.ko to be loaded with DHD. [ 11.487000] DHD_FKB_POOL size is:1280 and entry size:2592 [ 11.488000] fkbpool address range: d4c00000 <-> d4f2a000 [ 11.489000] DHD_PKTTAG POOL size is:1280 and entry size:64 [ 11.490000] dhd_module_init in [ 11.491000] dhd_queue_budget = 256 [ 11.492000] dhd_sta_threshold = 2048 [ 11.493000] dhd_if_threshold = 65536 [ 11.494000] no wifi platform data, skip [ 11.495000] PCI_PROBE: bus 1, slot 0,vendor 14E4, device AA52(good PCI location) [ 11.496000] dhdpcie_init: can't find adapter info for this chip [ 11.497000] pcieh 0000:01:00.0: enabling device (0140 -> 0142) [ 11.613000] DHD: dongle ram size is set to 983040(orig 983040) at 0x180000 [ 11.620000] dhd:0: fw path:/etc/wlan_dhd nv path:(null) [ 11.625000] RDPA returned tx wakeup reg = <0x80299004>, val = <0x10000000> [ 11.632000] RDPA returned rx wakeup reg = <0x8029a004>, val = <0x28000000> [ 11.640000] dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 [ 11.650000] dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0) [ 11.658000] dhd_attach(): thread:dhd_watchdog_thread:1b2 started [ 11.664000] dhd_attach(): thread:dhd0_dpc:1b3 started [ 11.669000] dhd_deferred_work_init: work queue initialized [ 11.674000] Creating CPU ring for queue number 0 with 1024 packets descriptor=0xbf1f37bc Creating CPU ring for queue number 1 with 1024 packets descriptor=0xbf1f37d8 wfd_bind: Dev wl%d wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3 [ 11.690000] Instantiating WFD 0 thread [ 11.707000] dhd:0: fw path:/etc/wlan_dhd nv path:(null) [ 11.712000] dhd_bus_download_firmware: firmware path=/etc/wlan_dhd, nvram path= [ 11.719000] update_firmware_path: pfw_path = /etc/wlan_dhd [ 11.725000] dhdpcie_ramsize_adj: Enter [ 11.833000] dhdpcie_download_code_file: download firmware /etc/wlan_dhd/43602a3/rtecdc.bin [ 11.900000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board) [ 11.907000] wl: ID=pci/0/1/0/ [ 11.910000] wl: ID=pci/0/1/0/ [ 11.913000] wl: loading /etc/wlan/bcm43602_map.bin [ 11.939000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19 [ 11.945000] Replace or append with internal Mac Address [ 11.951000] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. [ 11.994000] PCIe shared addr (0x001b49d8) read took 35023 usec before dongle is ready [ 12.002000] DMA RX offset from shared Area 0 [ 12.006000] dhdpcie_readshared: Dongle advertizes 2 size indices [ 12.012000] dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it [ 12.021000] H2D DMA WR INDX : array size 416 = 2 * 198 [ 12.026000] D2H DMA RD INDX : array size 32 = 2 * 3 [ 12.031000] D2H DMA WR INDX : array size 32 = 2 * 3 [ 12.036000] H2D DMA RD INDX : array size 416 = 2 * 198 [ 12.042000] ring_info_raw: 56 [ 12.045000] 88 9e 26 00 18 ab 26 00 a4 ac 26 00 30 ae 26 00 [ 12.051000] 36 ae 26 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.056000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 12.062000] 00 00 00 00 c6 00 00 00 [ 12.066000] dhdpcie_readshared: max H2D queues 198 [ 12.071000] dhd_bus_start: Initializing 198 h2drings [ 12.081000] dhd_runner_flowmgr_init: bootmem name<dhd0> addr<cc000000> size<11534336> [ 12.088000] dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512 [ 12.097000] dhd_runner_policy_init: N+M Policy = 0 1 (HW) [ 12.103000] dhd_bus_cmn_writeshared: [ 12.106000] 0000: 00 70 11 16 00 00 00 00 [ 12.111000] dhd_bus_cmn_writeshared: [ 12.114000] 0000: 00 00 a6 00 00 00 00 00 [ 12.119000] dhd_bus_cmn_writeshared: [ 12.122000] 0000: 00 00 30 15 00 00 00 00 [ 12.127000] dhd_bus_cmn_writeshared: [ 12.130000] 0000: 00 40 4f 00 00 00 00 00 [ 12.135000] dhd_bus_cmn_writeshared: [ 12.138000] 0000: 00 80 a6 00 00 00 00 00 [ 12.143000] dhd_bus_cmn_writeshared: [ 12.146000] 0000: 00 00 40 15 00 00 00 00 [ 12.151000] dhd_bus_cmn_writeshared: [ 12.155000] 0000: 00 10 14 00 [ 12.158000] dhd_bus_cmn_writeshared: [ 12.162000] 0000: 00 c8 2d 15 00 00 00 00 [ 12.166000] dhd_bus_cmn_writeshared: [ 12.170000] 0000: 00 cc 2d 15 00 00 00 00 [ 12.174000] dhd_bus_cmn_writeshared: [ 12.178000] 0000: 00 c0 2d 15 00 00 00 00 [ 12.182000] dhd_bus_cmn_writeshared: [ 12.186000] 0000: 00 c4 2d 15 00 00 00 00 [ 12.190000] Attach flowrings pool for 196 rings [ 12.195000] Runner DHD PCIE: vendor<0x14e4> device<0xaa52> bus<1> slot<0> [ 12.203000] Initial configuration [ 12.206000] ================================= [ 12.211000] rx_post_flow_ring_base_addr : c0a60000 [ 12.216000] tx_post_flow_ring_base_addr : cbfc4000 [ 12.221000] rx_complete_flow_ring_base_addr : c0a68000 [ 12.226000] tx_complete_flow_ring_base_addr : c04f4000 [ 12.232000] [ 12.233000] r2d_wr_arr_base_addr : e1669000 [ 12.238000] d2r_rd_arr_base_addr : e1669402 [ 12.242000] r2d_rd_arr_base_addr : e1669c00 [ 12.246000] d2r_wr_arr_base_addr : e1669802 [ 12.251000] tx_post_mgmt_arr_base_addr : e166a000 [ 12.256000] tx_post_mgmt_arr_base_phys_addr : 0x152dd000 [ 12.261000] [ 12.263000] r2d_wr_arr_base_phys_addr : 0x152dc000 [ 12.268000] d2r_rd_arr_base_phys_addr : 0x152dc402 [ 12.273000] r2d_rd_arr_base_phys_addr : 0x152dcc00 [ 12.278000] d2r_wr_arr_base_phys_addr : 0x152dc802 [ 12.283000] [ 12.284000] Doorbell ISR : bf635a84 [ 12.288000] Doorbell CTX : d613f600 [ 12.292000] Creating CPU ring for queue number 7 with 128 packets descriptor=0xbef42230, size_of_entry 16 [ 12.302000] Done initializing Ring 7 Base=0xe0822000 End=0xe0822800 calculated entries= 128 RDD Base=c1e000K descriptor=0xbef42230 [ 12.314000] Runner DHD Offload initialization complete [ 12.322000] CUR_ETHERADDR : 6 [ 12.323000] 20 b0 01 8c 65 29 [ 12.326000] dhd_sync_with_dongle: GET_REVINFO device 0x43bb, vendor 0x14e4, chipnum 0xaa52 [ 12.331000] [ 12.331000] Dongle Host Driver, version 7.14.164.19.cpe5.02L03.0-kdb [ 12.335000] wfd_registerdevice Successfully registered dev wl0 ifidx 0 wfd_idx 0 [ 12.336000] PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location) [ 12.337000] dhdpcie_init: can't find adapter info for this chip [ 12.338000] pcieh 0001:01:00.0: enabling device (0140 -> 0142) [ 12.457000] DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000 [ 12.458000] dhd:1: fw path:/etc/wlan_dhd nv path:(null) [ 12.459000] RDPA returned tx wakeup reg = <0x80299004>, val = <0x11000000> [ 12.460000] RDPA returned rx wakeup reg = <0x8029a004>, val = <0x29000000> [ 12.460000] dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 [ 12.464000] dhd_prealloc_attach: pre-allocated buffer mode is disabled (allocskbsz=0) [ 12.465000] dhd_attach(): thread:dhd_watchdog_thread:1c0 started [ 12.466000] dhd_attach(): thread:dhd1_dpc:1c1 started [ 12.467000] dhd_deferred_work_init: work queue initialized [ 12.468000] Creating CPU ring for queue number 2 with 1024 packets descriptor=0xbf1f37f4 Creating CPU ring for queue number 3 with 1024 packets descriptor=0xbf1f3810 wfd_bind: Dev wl%d wfd_idx 1 wl_radio_idx 1 Type fkb configured WFD thread wfd1-thrd minQId/maxQId (10/11), status (0) qmask 0xc [ 12.471000] dhd:1: fw path:/etc/wlan_dhd nv path:(null) [ 12.471000] Instantiating WFD 1 thread [ 12.473000] dhd_bus_download_firmware: firmware path=/etc/wlan_dhd, nvram path= [ 12.474000] update_firmware_path: pfw_path = /etc/wlan_dhd [ 12.475000] dhdpcie_ramsize_adj: Enter [ 12.524000] CONSOLE: hndarm_armr addr: 0x18002000, cr4_idx: 0 [ 12.529000] CONSOLE: 000000.001 [ 12.532000] CONSOLE: RTE (PCIE-MSG_BUF) 7.76.5 (r698973) on BCM43602 r3 @ 40.0/160.0/160.0MHz [ 12.541000] CONSOLE: 000000.002 allocating a max of 511 rxcplid buffers [ 12.548000] CONSOLE: 000000.003 pciemsgbuf0: Broadcom PCIE MSGBUF driver [ 12.555000] CONSOLE: 000000.005 reclaim section 0: Returned 48388 bytes to the heap [ 12.563000] CONSOLE: 000000.025 wl0: wlc_stf_txcore_shmem_write: No clock [ 12.570000] CONSOLE: 000000.030 wl0: Broadcom BCM43602 802.11 Wireless Controller 7.76.5 (r698973) [ 12.579000] CONSOLE: 000000.030 TCAM: 256 used: 56 exceed:0 [ 12.585000] CONSOLE: 000000.031 reclaim section 1: Returned 143420 bytes to the heap [ 12.593000] CONSOLE: [ 12.643000] dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000 [ 12.649000] dhdpcie_download_code_file: download firmware /etc/wlan_dhd/4366c0/rtecdc.bin [ 13.003000] wl:srom/otp not programmed, using main memory mapped srom info(wombo board) [ 13.004000] wl: ID=pci/1/1/0/ [ 13.005000] wl: ID=pci/1/1/0/ [ 13.033000] wl: loading /etc/wlan/bcm43664_map.bin [ 13.040000] wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=19 [ 13.041000] wl: reading /etc/wlan/bcm43664_nvramvars.bin, file size=173 [ 13.042000] Replace or append with internal Mac Address [ 13.045000] dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. [ 13.100000] PCIe shared addr (0x002a165c) read took 54023 usec before dongle is ready [ 13.101000] DMA RX offset from shared Area 0 [ 13.102000] dhdpcie_readshared: Dongle advertizes 2 size indices [ 13.103000] dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it [ 13.104000] H2D DMA WR INDX : array size 544 = 2 * 266 [ 13.105000] D2H DMA RD INDX : array size 32 = 2 * 3 [ 13.106000] D2H DMA WR INDX : array size 32 = 2 * 3 [ 13.106000] H2D DMA RD INDX : array size 544 = 2 * 266 [ 13.107000] ring_info_raw: 56 [ 13.108000] d4 6a 43 00 a4 7b 43 00 b8 7d 43 00 cc 7f 43 00 [ 13.113000] d2 7f 43 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 13.118000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 13.123000] 00 00 00 00 0a 01 00 00 [ 13.126000] dhdpcie_readshared: max H2D queues 266 [ 13.127000] dhd_bus_start: Initializing 266 h2drings [ 13.134000] dhd_runner_flowmgr_init: bootmem name<dhd1> addr<cb200000> size<14680064> [ 13.135000] dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 01:0512 [ 13.136000] dhd_runner_policy_init: N+M Policy = 0 1 (HW) [ 13.137000] dhd_bus_cmn_writeshared: [ 13.138000] 0000: 00 d0 00 18 00 00 00 00 [ 13.139000] dhd_bus_cmn_writeshared: [ 13.140000] 0000: 00 00 a7 00 00 00 00 00 [ 13.141000] dhd_bus_cmn_writeshared: [ 13.142000] 0000: 00 a0 17 16 00 00 00 00 [ 13.143000] dhd_bus_cmn_writeshared: [ 13.144000] 0000: 00 80 a7 00 00 00 00 00 [ 13.145000] dhd_bus_cmn_writeshared: [ 13.146000] 0000: 00 00 a8 00 00 00 00 00 [ 13.147000] dhd_bus_cmn_writeshared: [ 13.148000] 0000: 00 00 20 16 00 00 00 00 [ 13.149000] dhd_bus_cmn_writeshared: [ 13.150000] 0000: 00 10 14 00 [ 13.151000] dhd_bus_cmn_writeshared: [ 13.152000] 0000: 00 88 21 15 00 00 00 00 [ 13.153000] dhd_bus_cmn_writeshared: [ 13.154000] 0000: 00 8c 21 15 00 00 00 00 [ 13.154000] dhd_bus_cmn_writeshared: [ 13.155000] 0000: 00 80 21 15 00 00 00 00 [ 13.155000] dhd_bus_cmn_writeshared: [ 13.156000] 0000: 00 84 21 15 00 00 00 00 [ 13.157000] Attach flowrings pool for 264 rings [ 13.158000] Runner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0> [ 13.158000] Initial configuration [ 13.159000] ================================= [ 13.160000] rx_post_flow_ring_base_addr : c0a70000 [ 13.161000] tx_post_flow_ring_base_addr : cb1c4000 [ 13.162000] rx_complete_flow_ring_base_addr : c0a80000 [ 13.163000] tx_complete_flow_ring_base_addr : c0a78000 [ 13.164000] [ 13.165000] r2d_wr_arr_base_addr : e1679000 [ 13.166000] d2r_rd_arr_base_addr : e1679402 [ 13.166000] r2d_rd_arr_base_addr : e1679c00 [ 13.167000] d2r_wr_arr_base_addr : e1679802 [ 13.168000] tx_post_mgmt_arr_base_addr : e167a000 [ 13.169000] tx_post_mgmt_arr_base_phys_addr : 0x15219000 [ 13.170000] [ 13.171000] r2d_wr_arr_base_phys_addr : 0x15218000 [ 13.172000] d2r_rd_arr_base_phys_addr : 0x15218402 [ 13.173000] r2d_rd_arr_base_phys_addr : 0x15218c00 [ 13.174000] d2r_wr_arr_base_phys_addr : 0x15218802 [ 13.175000] [ 13.176000] Doorbell ISR : bf635a84 [ 13.176000] Doorbell CTX : d758aa00 [ 13.177000] Creating CPU ring for queue number 1 with 128 packets descriptor=0xbef42038, size_of_entry 16 [ 13.178000] Done initializing Ring 1 Base=0xe0830000 End=0xe0830800 calculated entries= 128 RDD Base=c2c000K descriptor=0xbef42038 [ 13.179000] Runner DHD Offload initialization complete [ 13.181000] CUR_ETHERADDR : 6 [ 13.184000] 22 b0 01 8c 65 31 [ 13.187000] dhd_sync_with_dongle: GET_REVINFO device 0x43c5, vendor 0x14e4, chipnum 0xaa90 [ 13.197000] [ 13.197000] Dongle Host Driver, version 7.14.164.19.cpe5.02L03.0-kdb [ 13.207000] wfd_registerdevice Successfully registered dev wl1 ifidx 0 wfd_idx 1 [ 13.214000] Broadcom PCI Device 0x6313 has allocated with driver pcieport [ 13.221000] Broadcom PCI Device 0x6313 has allocated with driver pcieport [ 13.231000] dhd_module_init out [ 13.240000] bcmxtmcfg: bcmxtmcfg_init entry [ 13.249000] adsl: adsl_init entry [ 13.258000] usbcore: registered new interface driver usbserial [ 13.259000] usbcore: registered new interface driver GobiSerial [ 13.261000] usbserial: USB Serial support registered for GobiSerial [ 13.262000] GobiSerial: 2015-08-27/SWI_2.25:GobiSerial [ 13.266000] [DSPHAL] dsphal_init: Starting DSPHAL driver. [ 13.267000] [DSPHAL] Retrieving VoiceParms boardIdStr: VCNT-I baseBoardIdStr: VCNT-I ret: 0 [ 13.300000] [DSPHAL] pcm_clk_init: starting PCM clock [ 13.301000] [DSPHAL] pcm_nco_mux_cfg: using MISC for NCO FCW [ 13.302000] [DSPHAL] pcm_nco_init: PCM clock in normal mode [ 13.303000] [DSPHAL] pcm_nco_init: loading MISC FCW to PCM NCO: 0xa7c5ac47 [ 13.304000] [DSPHAL] dh_configure_channel: device 0, channel 0, id 0, devType 10, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0 [ 13.304000] [DSPHAL] pcm_config_channel: channel 0 [ 13.305000] [DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0 [ 13.306000] [DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 0, 16-bit 0] assigned to channel 0 as buffer channel 0 [ 13.307000] [DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0 [ 13.308000] [DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 1, 16-bit 0] assigned to channel 0 as buffer channel 0 [ 13.309000] [DSPHAL] dh_configure_channel: device 0, channel 1, id 1, devType 10, intfType 0, status 0, chanType 0, rate 8000 Hz, comp 0 [ 13.310000] [DSPHAL] pcm_config_channel: channel 1 [ 13.310000] [DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1 [ 13.311000] [DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 2, 16-bit 1] assigned to channel 1 as buffer channel 1 [ 13.312000] [DSPHAL] pcm_ts_alloc: DMA 4 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1 [ 13.313000] [DSPHAL] pcm_ts_alloc: DMA 5 timeslot [8-bit 3, 16-bit 1] assigned to channel 1 as buffer channel 1 [ 13.318000] [SLICSLAC] slicslac_init: Starting SLIC/SLAC driver. [ 13.321000] jnl: driver (9.4.4 9.4.4, LBD=ON) loaded at bf7ca000 [ 13.331000] ufsd: driver (9.4.4 9.4.4, ioctl, sd2(5), car) loaded at bf7d9000 [ 13.331000] NTFSJ support included [ 13.331000] Hfs+ support included [ 13.338000] usbcore: registered new interface driver cdc_acm [ 13.339000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 13.341000] usbcore: registered new interface driver cdc_wdm [ 13.346000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 13.351000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 13.402000] nf_conntrack version 0.5.0 (6803 buckets, 27212 max) [ 13.430000] CONSOLE: 000000.000 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.431000] CONSOLE: 000000.000 initvars_cis_pci: Not CIS format [ 13.432000] CONSOLE: 000000.000 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.435000] CONSOLE: 000000.000 ipxotp_read_region: h/w region not programmed [ 13.437000] ctnetlink v0.93: registering with nfnetlink. [ 13.439000] nf_conntrack_rtsp v0.7 loading [ 13.451000] CONSOLE: 000000.000 Neither SPROM nor OTP has valid image [ 13.458000] CONSOLE: 000000.000 srom rev:0 [ 13.462000] CONSOLE: 000000.000 initvars_srom_pci, SROM CRC Error [ 13.468000] CONSOLE: 000000.000 initvars_srom_pci, Using external nvram [ 13.475000] CONSOLE: 000000.000 Setting clocks to 800/400/200 [ 13.479000] nf_nat_rtsp v0.7 loading [ 13.485000] CONSOLE: 000000.000 si_set_bb_vcofreq_frac: only work on 4360, 4350 [ 13.492000] CONSOLE: 000000.000 Enabling D-cache [ 13.497000] CONSOLE: 026738.568 gic_dist_init max_irq 64 [ 13.502000] CONSOLE: 026738.569 c_init: Watchdog reset bit set, clearing [ 13.506000] xt_time: kernel timezone is -0000 [ 13.507000] usbcore: registered new interface driver cdc_ether [ 13.509000] usbcore: registered new interface driver cdc_ncm [ 13.510000] usbcore: registered new interface driver huawei_cdc_ncm [ 13.517000] usbcore: registered new interface driver option [ 13.517000] usbserial: USB Serial support registered for GSM modem (1-port) [ 13.518000] usbcore: registered new interface driver qcserial [ 13.519000] usbserial: USB Serial support registered for Qualcomm USB modem [ 13.520000] usbcore: registered new interface driver qmi_wwan [ 13.521000] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.571000] CONSOLE: 026738.569 [ 13.574000] CONSOLE: RTE (PCIE-MSG_BUF) 10.10.122.22 (r696077) on BCM43664 r4 @ 40.0/200.0/800.0MHz [ 13.584000] CONSOLE: 026738.569 nvram_init: called again without calling nvram_exit() [ 13.585000] CONSOLE: 026738.569 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.586000] CONSOLE: 026738.569 initvars_cis_pci: Not CIS format [ 13.587000] CONSOLE: 026738.569 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.588000] CONSOLE: 026738.569 ipxotp_read_region: h/w region not programmed [ 13.589000] CONSOLE: 026738.569 Neither SPROM nor OTP has valid image [ 13.590000] CONSOLE: 026738.569 srom rev:0 [ 13.591000] CONSOLE: 026738.569 initvars_srom_pci, SROM CRC Error [ 13.592000] CONSOLE: 026738.569 initvars_srom_pci, Using external nvram [ 13.593000] CONSOLE: 026738.569 allocating a max of 511 rxcplid buffers [ 13.593000] CONSOLE: 026738.570 pciemsgbuf0: Broadcom PCIE MSGBUF driver [ 13.594000] CONSOLE: 026738.570 nvram_init: called again without calling nvram_exit() [ 13.594000] CONSOLE: 026738.570 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.595000] CONSOLE: 026738.570 initvars_cis_pci: Not CIS format [ 13.596000] CONSOLE: 026738.570 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.597000] CONSOLE: 026738.570 ipxotp_read_region: h/w region not programmed [ 13.598000] CONSOLE: 026738.570 Neither SPROM nor OTP has valid image [ 13.599000] CONSOLE: 026738.570 srom rev:0 [ 13.599000] CONSOLE: 026738.570 initvars_srom_pci, SROM CRC Error [ 13.600000] CONSOLE: 026738.570 initvars_srom_pci, Using external nvram [ 13.601000] CONSOLE: 026738.570 wlc_ucode_download: wl0: Loading non-MU ucode [ 13.602000] CONSOLE: 026738.571 reclaim section 0: Returned 216 bytes to the heap [ 13.603000] CONSOLE: 026738.571 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.604000] CONSOLE: 026738.571 initvars_cis_pci: Not CIS format [ 13.605000] CONSOLE: 026738.572 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.605000] CONSOLE: 026738.572 ipxotp_read_region: h/w region not programmed [ 13.606000] CONSOLE: 026738.572 Neither SPROM nor OTP has valid image [ 13.606000] CONSOLE: 026738.572 srom rev:0 [ 13.607000] CONSOLE: 026738.572 initvars_srom_pci, SROM CRC Error [ 13.608000] CONSOLE: 026738.572 initvars_srom_pci, Using external nvram [ 13.609000] CONSOLE: 026738.572 wlc_bmac_attach, deviceid 0x43c5 nbands 1 [ 13.610000] CONSOLE: 026738.581 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 [ 13.611000] CONSOLE: 026738.581 wl1: wlc_bmac_attach: chiprev 4 corerev 65 cccap 0x58400009 maccap 0xf0018705 band 5G, phy_type 11 phy_rev 33 [ 13.612000] CONSOLE: 026738.581 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 [ 13.613000] CONSOLE: 026738.581 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 [ 13.613000] CONSOLE: 026738.582 wl1: wlc_stf_txcore_shmem_write: No clock [ 13.613000] CONSOLE: 026738.583 wl1: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 512 [ 13.614000] CONSOLE: 026738.585 wl_eventq_dup_event: wl_eventq not initialized [ 13.615000] CONSOLE: 026738.585 wl_eventq_dup_event: wl_eventq not initialized [ 13.616000] CONSOLE: 026738.585 wl1: Broadcom BCM43664 802.11 Wireless Controller 10.10.122.22 (r696077) [ 13.617000] CONSOLE: 026738.585 SPLITRX_MODE_2 enabled : tcmsegsize 160 [ 13.618000] CONSOLE: 026738.585 TCAM: 512 used: 257 exceed:0 [ 13.619000] CONSOLE: 026738.585 reclaim section 1: Returned 180964 bytes to the heap [ 13.620000] CONSOLE: 026738.586 ThreadX v5.6 initialized [ 13.620000] CONSOLE: [ 13.621000] CONSOLE: 026738.931 wl1: wlc_enable_probe_req: state down, deferring setting of host flags [ 13.622000] CONSOLE: 026738.931 wl1: wlc_enable_probe_req: state down, deferring setting of host flags Note: Loading 6300 MDK (default) driver for 0 chip Switch MDK: num_switches = 1 [63100] Switch MDK: unit = 1; phy_pbmp = 0xf; config_pbmp = 0xf nophy_pbmp = 0x0 Switch MDK link poll thread: unit=1; phypbmp=0xf config_pbmp=0xf Checking country codes in /etc/wlan/brcm_country_map_2G (wl0) Checking E0/784 --> OK Checking Q1/45 --> OK Checking country codes in /etc/wlan/brcm_country_map_5G (wl1) Checking E0/784 --> OK Checking Q1/45 --> OK Updating radar thresholds Hostapd starting... (1) Hostapd starting... (2)

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING

Please tell if these details refer to Sercomm or Technicolor hardware version

Sources

GPL toolchain and sources can be found here:

V3.5.01.12 GPL.zip MEGA

The OEM firmware for Technicolor version is Homware. It is compiled with an OpenWrt Broadcom-based cusotm toolchain. You can learn much more about Homeware on hack-technicolor.rtfs.io
The OEM firmware for Sercomm version is based on their proprietary stuff and is not derived from OpenWrt in any way.

How to add tags

BCM63136, 256flash, 512ram, 4port, GigabitEthernet, ADSL2+, VDSL2, ARM, SFP, Unsupported devices

bcm63136 256flash 512ram 4port gigabitethernet adsl2 vdsl2 arm SFP Unsupported devices

Vodafone Power Station / Vox30

OpenWrt support

Hardware highlights

Hardware

Info

Photos

Sercomm SHG3000

Board

Sercomm SHG3000

Opening the case

Serial

JTAG

Bootlogs

OEM bootlog

Sercomm SHG3000

Technicolor THG3000

OpenWrt bootlog

OEM Firmware

?HG300

Sources

Notes

Tags