User Tools

Site Tools


toh:netgear:r7000

Netgear Nighthawk R7000

NETGEAR's R7000 “Nighthawk” is a second generation Broadcom 802.11ac AC1900 router with storage sharing USB 2.0 & 3.0 ports.

R7000

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
R7000Broadcom BCM4709A01000128NAND256Broadcom BCM4360, BCM4360b/g/na/n/ac-5-1x 2.0, 1x 3.0

Installation

Flash Layout

FIXME

root@OpenWrt:~# cat /proc/mtd 
dev:    size   erasesize  name
mtd0: 00080000 00020000 "boot"
mtd1: 00180000 00020000 "nvram"
mtd2: 02000000 00020000 "firmware"
mtd3: 003fffe4 00020000 "linux"
mtd4: 01c00000 00020000 "ubi"
mtd5: 00040000 00020000 "board_data"
mtd6: 00040000 00020000 "POT"
mtd7: 00180000 00020000 "POT"
mtd8: 00040000 00020000 "ML"
mtd9: 00040000 00020000 "ML"
mtd10: 00040000 00020000 "ML"
mtd11: 00040000 00020000 "ML"
mtd12: 00040000 00020000 "ML"
mtd13: 05ac0000 00020000 "ML"

Upgrading OpenWrt

Basic configuration

Failsafe mode

Buttons

hardware.button on howto use and configure the hardware button(s).

Name GPIO Polarity
WPS 4 Active low
Wlan 5 Active low
Reset 6 Active low

LEDs

Color Name GPIO Polarity
White Power LED 2 Active low
Amber Power LED 3 Active low
White Wlan 5Ghz LED 12 Active low
White Wlan 2.4Ghz LED 13 Active low
White WPS Button 14 Active high
White Wlan Button 15 Active high
White USB_1 LED 17 Active low
White USB_2 LED 18 Active low

Hardware

Info

General
Brand Netgear
Model R7000
Versions
Device Type WiFi Router
Availability Available 2017
Comments - general
OpenWrt Support
Supported Since Revision
Supported Since Release 15.05
Supported Current Release 18.06.1
Unsupported
Hardware
Instruction set ARM
Sub Instruction Set ARMv7-A
bootloader CFE
Target bcm53xx
System-On-Chip
CPU MHz 1000
Flash MB 128NAND
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 5
switch Broadcom BCM4709A0
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware
Detachable Antennas 3
Comments - WLAN 3x3
Interfaces
USB ports 1x 2.0, 1x 3.0
SATA ports -
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count ¿
Button count ¿
Power supply
Links
Forum Topic URL
WikiDevi URL https://wikidevi.com/wiki/Netgear_R7000
OEM device homepage URL
Firmware OEM Stock URL http://support.netgear.de/product/R7000
Firmware OpenWrt Install URL http://downloads.openwrt.org/releases/18.06.1/targets/bcm53xx/generic/openwrt-18.06.1-bcm53xx-netgear-r7000-squashfs.chk
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/releases/18.06.1/targets/bcm53xx/generic/openwrt-18.06.1-bcm53xx-netgear-r7000-squashfs.chk
Edit the underlying data View/Edit data

Photos

Model Number

Front:

Photo of front of the casing

Back:

Photo of back of the casing

Opening the case

Note: This will void your warranty!

  • To remove the cover do a/b/c

Main PCB

Photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

**Photo of PCB with markings**

Console settings: 115200 8-N-1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

Debricking

Bootlogs

Openwrt dmesg

BusyBox v1.23.2 (2015-08-24 19:14:13 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r46717) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.18.20 (buildbot@debian-amd64) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46717) ) #1 SMP Mon Aug 24 19:26:26 UTC 2015 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Netgear R7000 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat c03d7640, node_mem_map c7ef8000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] PERCPU: Embedded 9 pages/cpu @c7ee1000 s5952 r8192 d22720 u36864 [ 0.000000] pcpu-alloc: s5952 r8192 d22720 u36864 alloc=9*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 125548K/131072K available (2910K kernel code, 106K rwdata, 792K rodata, 176K init, 276K bss, 5524K reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03a5dcc (3704 kB) [ 0.000000] .init : 0xc03a6000 - 0xc03d2000 ( 176 kB) [ 0.000000] .data : 0xc03d2000 - 0xc03ecbf8 ( 107 kB) [ 0.000000] .bss : 0xc03ecbf8 - 0xc0431d4c ( 277 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: platform modifies aux control register: 0x0a130000 -> 0x7a530001 [ 0.000000] L2C: platform provided aux values permit register corruption. [ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x7a530001 [ 0.000000] L2C-310 erratum 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310: enabling full line of zeros but not enabled in Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001 [ 0.000014] sched_clock: 64 bits at 400MHz, resolution 2ns, wraps every 2748779069440ns [ 0.010415] Calibrating delay loop... 1594.16 BogoMIPS (lpj=7970816) [ 0.103843] pid_max: default: 32768 minimum: 301 [ 0.109879] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.118284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.127716] CPU: Testing write buffer coherency: ok [ 0.134194] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.141514] Setting up static identity map for 0x11a80 - 0x11ab4 [ 0.151035] CPU1: Booted secondary processor [ 0.190232] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.190312] Brought up 2 CPUs [ 0.206792] SMP: Total of 2 processors activated (3188.32 BogoMIPS). [ 0.214871] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13) [ 0.225551] CPU: This may indicate a broken bootloader or firmware. [ 0.240555] NET: Registered protocol family 16 [ 0.246938] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.282389] Switched to clocksource arm_global_timer [ 0.289881] NET: Registered protocol family 2 [ 0.296238] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.305113] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.313215] TCP: Hash tables configured (established 1024 bind 1024) [ 0.321338] TCP: reno registered [ 0.325496] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.332945] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.341176] NET: Registered protocol family 1 [ 0.346792] PCI: CLS 0 bytes, default 64 [ 0.347783] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.356420] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.363886] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.376455] msgmni has been set to 245 [ 0.381790] io scheduler noop registered [ 0.386817] io scheduler deadline registered (default) [ 0.393736] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.403951] console [ttyS0] disabled [ 0.408585] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 117, base_baud = 7812500) is a 16550 [ 0.419867] console [ttyS0] enabled [ 0.428718] bootconsole [earlycon0] disabled [ 0.441023] libphy: Fixed MDIO Bus: probed [ 0.446236] bgmac: Broadcom 47xx GBit MAC driver loaded [ 0.453024] bcma: bus0: Found chip with id 53010, rev 0x00 and package 0x00 [ 0.461829] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0) [ 0.472593] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.472607] bcma: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x01, class 0x0) [ 0.483577] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.483590] bcma: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0) [ 0.493590] bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.504124] bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.514654] bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.525188] bcma: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0) [ 0.535689] bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.546412] bcma: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.557149] bcma: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0) [ 0.567915] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.567928] bcma: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0) [ 0.580524] bcma: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0) [ 0.591057] bcma: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0) [ 0.601590] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.601603] bcma: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0) [ 0.611915] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.611929] bcma: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0) [ 0.622022] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.622035] bcma: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0) [ 0.633765] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.633777] bcma: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0) [ 0.647253] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.647265] bcma: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0) [ 0.657361] bcma: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0) [ 0.669421] bcma: bus0: bcma_of_get_irq() failed with rc=-22 [ 0.669434] bcma: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0) [ 0.690280] bcm_nand bcma0:18: NAND Controller rev 6.01 [ 0.720309] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.728270] nand: Macronix NAND 128MiB 3,3V 8-bit [ 0.734185] nand: 128MiB, SLC, page size: 2048, OOB size: 64 [ 1.080421] mtd_read error while parsing (offset: 0x1CE0000)! [ 1.317781] mtd_read error while parsing (offset: 0x30E0000)! [ 1.999712] random: nonblocking pool is initialized [ 2.302171] 14 bcm47xxpart partitions found on MTD device bcm_nand [ 2.309917] Creating 14 MTD partitions on "bcm_nand": [ 2.316263] 0x000000000000-0x000000080000 : "boot" [ 2.324160] 0x000000080000-0x000000200000 : "nvram" [ 2.334398] 0x000000200000-0x000002200000 : "firmware" [ 2.414534] 0x00000020001c-0x000000600000 : "linux" [ 2.430549] 0x000000600000-0x000002200000 : "ubi" [ 2.500998] 0x000002200000-0x000002240000 : "board_data" [ 2.508925] 0x000002240000-0x000002280000 : "POT" [ 2.516123] 0x000002280000-0x000002400000 : "POT" [ 2.526171] 0x000002400000-0x000002440000 : "ML" [ 2.533275] 0x000002440000-0x000002480000 : "ML" [ 2.540387] 0x000002480000-0x0000024c0000 : "ML" [ 2.547469] 0x0000024c0000-0x000002500000 : "ML" [ 2.554547] 0x000002500000-0x000002540000 : "ML" [ 2.561625] 0x000002540000-0x000008000000 : "ML" [ 2.776152] bcm53xxspiflash spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff [ 2.785358] bcm53xxspiflash: probe of spi32766.0 failed with error -2 [ 2.824457] bcma: bus0: Using SPROM revision 11 provided by platform. [ 2.824748] bgmac bcma0:3: Found PHY addr: 30 (NOREGS) [ 2.831966] bgmac bcma0:3: Support for Roboswitch not implemented [ 2.841211] b53_common: found switch: BCM53012, rev 5 [ 2.848281] bgmac bcma0:4: Found PHY addr: 0 [ 2.855460] bgmac: Timeout waiting for reg 0x180 [ 2.861281] bgmac bcma0:4: Writing to PHY 0 register 0x0 failed [ 2.869828] bgmac: Timeout waiting for reg 0x180 [ 2.875627] bgmac bcma0:4: Reading PHY 0 register 0x0 failed [ 2.882725] bgmac bcma0:4: PHY reset failed [ 2.887961] bgmac bcma0:4: Support for Roboswitch not implemented [ 2.896644] bgmac bcma0:5: Invalid MAC addr: 00:00:00:00:00:00 [ 2.904026] bgmac bcma0:5: Using random MAC: 36:a7:7a:b8:39:be [ 2.911389] bgmac bcma0:5: Found PHY addr: 0 [ 2.918495] bgmac: Timeout waiting for reg 0x180 [ 2.924300] bgmac bcma0:5: Writing to PHY 0 register 0x0 failed [ 2.932851] bgmac: Timeout waiting for reg 0x180 [ 2.938641] bgmac bcma0:5: Reading PHY 0 register 0x0 failed [ 2.945741] bgmac bcma0:5: PHY reset failed [ 2.950986] bgmac bcma0:5: Support for Roboswitch not implemented [ 2.959626] bgmac: Unsupported core_unit 3 [ 2.964806] bgmac: probe of bcma0:6 failed with error -524 [ 2.971804] pci_host_bcm5301x bcma0:7: initializing PCIe controller [ 3.250257] pci_host_bcm5301x bcma0:7: link: UP [ 3.256060] pci_host_bcm5301x bcma0:7: PCI host bridge to bus 0000:00 [ 3.264163] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff] [ 3.272787] pci_bus 0000:00: root bus resource [io 0x0000] [ 3.279774] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.289736] pci 0000:00:00.0: [14e4:8012] type 01 class 0x020000 [ 3.289798] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 3.289988] PCI: bus0: Fast back to back transfers disabled [ 3.297136] pci 0000:01:00.0: [14e4:4360] type 00 class 0x028000 [ 3.297176] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 3.297285] pci 0000:01:00.0: supports D1 D2 [ 3.297464] PCI: bus1: Fast back to back transfers disabled [ 3.304472] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.304491] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 3.304595] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff] [ 3.313118] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit] [ 3.322300] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.328531] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff] [ 3.337191] pci_host_bcm5301x bcma0:8: initializing PCIe controller [ 3.620251] pci_host_bcm5301x bcma0:8: link: UP [ 3.626056] pci_host_bcm5301x bcma0:8: PCI host bridge to bus 0001:00 [ 3.634159] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff] [ 3.642784] pci_bus 0001:00: root bus resource [io 0x0000] [ 3.649770] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.659723] pci 0001:00:00.0: [14e4:8012] type 01 class 0x020000 [ 3.659781] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold [ 3.659974] PCI: bus0: Fast back to back transfers disabled [ 3.667117] pci 0001:01:00.0: [14e4:4360] type 00 class 0x028000 [ 3.667159] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 3.667266] pci 0001:01:00.0: supports D1 D2 [ 3.667439] PCI: bus1: Fast back to back transfers disabled [ 3.674446] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.674465] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to 01 [ 3.674614] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x400fffff] [ 3.683137] pci 0001:01:00.0: BAR 0: assigned [mem 0x40000000-0x40007fff 64bit] [ 3.692318] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.698547] pci 0001:00:00.0: bridge window [mem 0x40000000-0x400fffff] [ 3.707221] pci_host_bcm5301x bcma0:9: initializing PCIe controller [ 4.100253] pci_host_bcm5301x bcma0:9: link: DOWN [ 4.107373] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 4.118642] bcma: bus0: Bus registered [ 4.123507] bcma-pci-bridge 0000:01:00.0: enabling device (0140 -> 0142) [ 4.131952] bcma: bus1: Found chip with id 0x4360, rev 0x03 and package 0x01 [ 4.140824] bcma: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0) [ 4.151522] bcma: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0) [ 4.162347] bcma: bus1: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0) [ 4.172739] bcma: bus1: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0) [ 4.183336] bcma: bus1: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0) [ 4.194528] bcma: bus1: Found rev 17 PMU (capabilities 0x10A22B11) [ 4.194539] bcma: bus1: SPROM offset 0x800 [ 4.233790] bcma: bus1: Invalid SPROM read from the PCIe card, trying to use fallback SPROM [ 4.268590] bcma: bus1: Using SPROM revision 11 provided by platform. [ 4.268610] bcma: bus1: PMU resource config unknown or not needed for device 0x4360 [ 4.270624] bcma: bus1: Workarounds unknown or not needed for device 0x4360 [ 4.270638] bcma: bus1: Switched to core: 0x83C [ 4.270999] bcma: bus1: Bus registered [ 4.275763] bcma-pci-bridge 0001:01:00.0: enabling device (0140 -> 0142) [ 4.284209] bcma: bus2: Found chip with id 0x4360, rev 0x03 and package 0x01 [ 4.293075] bcma: bus2: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2B, class 0x0) [ 4.303778] bcma: bus2: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x2A, class 0x0) [ 4.314602] bcma: bus2: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x02, class 0x0) [ 4.324993] bcma: bus2: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x01, class 0x0) [ 4.335589] bcma: bus2: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x11, class 0x0) [ 4.346777] bcma: bus2: Found rev 17 PMU (capabilities 0x10A22B11) [ 4.346787] bcma: bus2: SPROM offset 0x800 [ 4.386037] bcma: bus2: Invalid SPROM read from the PCIe card, trying to use fallback SPROM [ 4.417712] bcma: bus2: Using SPROM revision 11 provided by platform. [ 4.417730] bcma: bus2: PMU resource config unknown or not needed for device 0x4360 [ 4.419731] bcma: bus2: Workarounds unknown or not needed for device 0x4360 [ 4.419744] bcma: bus2: Switched to core: 0x83C [ 4.420085] bcma: bus2: Bus registered [ 4.425152] TCP: cubic registered [ 4.429319] NET: Registered protocol family 17 [ 4.434992] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 4.450838] Bridge firewalling registered [ 4.455874] 8021q: 802.1Q VLAN Support v1.8 [ 4.461193] Registering SWP/SWPB emulation handler [ 4.469535] UBI: auto-attach mtd4 [ 4.473732] UBI: attaching mtd4 to ubi0 [ 4.870845] UBI: scanning is finished [ 4.893131] UBI: attached mtd4 (name "ubi", size 28 MiB) to ubi0 [ 4.900715] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.909224] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.917634] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.926259] UBI: good PEBs: 223, bad PEBs: 1, corrupted PEBs: 0 [ 4.933678] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.942625] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1803316545 [ 4.953959] UBI: available PEBs: 0, total reserved PEBs: 223, PEBs reserved for bad PEB handling: 19 [ 4.965418] UBI: background thread "ubi_bgt0d" started, PID 290 [ 4.966643] UBI: ubiblock0_0 created from ubi0:0(rootfs) [ 4.966649] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.994477] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.003690] Freeing unused kernel memory: 176K (c03a6000 - c03d2000) [ 5.614348] init: Console is alive [ 5.618775] init: - watchdog - [ 5.622957] External imprecise Data abort at addr=0x0, fsr=0x1c06 ignored. [ 6.275336] usbcore: registered new interface driver usbfs [ 6.282327] usbcore: registered new interface driver hub [ 6.289068] usbcore: registered new device driver usb [ 6.641283] init: - preinit - [ 7.870271] eth0: Link is Up - 1Gbps/Full - flow control off [ 10.046979] UBIFS: background thread "ubifs_bgt0_1" started, PID 354 [ 10.147753] UBIFS: recovery needed [ 10.345562] UBIFS: recovery completed [ 10.350291] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 10.358374] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.369839] UBIFS: FS size: 21204992 bytes (20 MiB, 167 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs) [ 10.381834] UBIFS: reserved for root: 1001563 bytes (978 KiB) [ 10.389045] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7338089B-10F1-41E8-BA1C-B2F91567E847, small LPT model [ 10.405766] mount_root: switching to jffs2 overlay [ 10.430598] procd: - early - [ 10.434306] procd: - watchdog - [ 11.141332] procd: - ubus - [ 12.170977] procd: - init - [ 16.838991] NET: Registered protocol family 10 [ 16.848422] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.861774] Loading modules backported from Linux version master-2015-07-21-0-g47cd203 [ 16.871733] Backport generated by backports.git backports-20150626-0-gc1a4168 [ 16.882227] ip_tables: (C) 2000-2006 Netfilter Core Team [ 16.893760] nf_conntrack version 0.5.0 (1964 buckets, 7856 max) [ 16.970885] xt_time: kernel timezone is -0000 [ 16.984629] cfg80211: World regulatory domain updated: [ 16.991119] cfg80211: DFS Master region: unset [ 16.996588] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 17.008849] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.018906] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 17.028951] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 17.038989] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 17.050878] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 17.062757] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 17.072901] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 17.082928] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 17.110202] PPP generic driver version 2.4.2 [ 17.117181] NET: Registered protocol family 24 [ 17.136903] b43-phy0: Broadcom 4360 WLAN found (core revision 42) [ 17.144607] bcma: bus1: Switched to core: 0x812 [ 17.151135] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1) [ 17.161202] b43: probe of bcma1:1 failed with error -95 [ 17.167808] b43-phy1: Broadcom 4360 WLAN found (core revision 42) [ 17.175461] bcma: bus2: Switched to core: 0x812 [ 17.181121] b43-phy1 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1) [ 17.191171] b43: probe of bcma2:1 failed with error -95 [ 17.197816] Broadcom 43xx driver loaded [ Features: PNL ] [ 17.208962] usbcore: registered new interface driver brcmfmac [ 20.423129] device eth0.1 entered promiscuous mode [ 20.429162] device eth0 entered promiscuous mode [ 20.442516] br-lan: port 1(eth0.1) entered forwarding state [ 20.449567] br-lan: port 1(eth0.1) entered forwarding state [ 20.890343] eth0: Link is Up - 1Gbps/Full - flow control off [ 22.441107] br-lan: port 1(eth0.1) entered forwarding state


Notes

Tags

toh/netgear/r7000.txt · Last modified: 2018/05/01 19:50 by tmomas