Show pagesourceOld revisionsBacklinksBack to top × Table of Contents Linksys WRT150N An account of flashing OpenWrt to a WRT150N Why you should use brcm-2.4 Hardware Tags Linksys WRT150N This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram. DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 4/32 warning for details. 1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation. This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now. 2) OpenWrt support for this device will end after 2019. 19.07 will be the last official build for 4/32 devices. After 19.07, no further OpenWrt images will be built for 4/32 devices. See OpenWrt on 4/32 devices what you can do now. tried r39412 and it works without issues below is nvram without correction from '/etc/init.d/nvram (mtd erase mtd6 + reboot) then boot/klog/dmesg from r39412 and some some old stuff root@OpenWrt:/# nvram show | sort blink_diag_led=1 boardflags2=0 boardflags=0x0010 boardnum=42 boardrev=0x10 boardtype=0x0472 boot_hw_model=WRT150N boot_hw_ver=1 boot_ver=v4.3 boot_wait=off bootnv_ver=2 cardbus=1 clkfreq=264 diag_gpio=1 dl_ram_addr=a0001000 et0macaddr=00:1c:10:19:a4:e6 et0mdcport=0 et0phyaddr=30 et1macaddr=00:88:88:88:00:2a et1mdcport=0 et1phyaddr=4 lan_ipaddr=192.168.1.1 lan_netmask=255.255.255.0 mfg_wait=on os_flash_addr=bfc40000 os_ram_addr=80001000 parkid=0 pci/1/1/aa2g=3 pci/1/1/ag0=2 pci/1/1/ag1=2 pci/1/1/ag2=2 pci/1/1/boardflags2=1 pci/1/1/boardflags=0x200 pci/1/1/boardrev=0x4b pci/1/1/boardtype=0x46d pci/1/1/boardvendor=0x14e4 pci/1/1/bw40po=0 pci/1/1/bwduppo=0 pci/1/1/ccdpo=0 pci/1/1/cck2gpo=0 pci/1/1/ccode= pci/1/1/devid=0x4329 pci/1/1/itt2ga0=0 pci/1/1/itt2ga1=0 pci/1/1/ledbh0=8 pci/1/1/ledbh1=-1 pci/1/1/ledbh2=-1 pci/1/1/ledbh3=-1 pci/1/1/macaddr=00:88:88:88:00:2a pci/1/1/maxp2ga0=0 pci/1/1/maxp2ga1=0 pci/1/1/mcs2gpo0=0 pci/1/1/mcs2gpo1=0 pci/1/1/mcs2gpo2=0 pci/1/1/mcs2gpo3=0 pci/1/1/mcs2gpo4=0 pci/1/1/mcs2gpo5=0 pci/1/1/mcs2gpo6=0 pci/1/1/mcs2gpo7=0 pci/1/1/ofdm2gpo=0 pci/1/1/pa2gw0a0=0 pci/1/1/pa2gw0a1=0 pci/1/1/pa2gw1a0=0 pci/1/1/pa2gw1a1=0 pci/1/1/pa2gw2a0=0 pci/1/1/pa2gw2a1=0 pci/1/1/pa2gw3a0=0 pci/1/1/pa2gw3a1=0 pci/1/1/regrev=0 pci/1/1/sromrev=4 pci/1/1/stbcpo=0 pci/1/1/txpid2ga0=91 pci/1/1/txpid2ga1=91 pci/1/1/txpt2g=0x36 pci/1/1/venid=0x14e4 pmon_ver=CFE 4.101.27.0 scratch=a0180000 sdram_config=0x0062 sdram_init=0x054B sdram_ncdl=0x208 sdram_refresh=0x0 sromrev=4 tftpd_ipaddr=192.168.1.254 wait_time=3 watchdog=5000 wl0gpio0=8 klog/dmesg: [ 0.000000] Linux version 3.10.28 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39412) ) #1 Wed Jan 29 08:21:17 PST 2014 [ 0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300) [ 0.000000] bcm47xx: using ssb bus [ 0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00 [ 0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243) [ 0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243) [ 0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243) [ 0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243) [ 0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243) [ 0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243) [ 0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243) [ 0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243) [ 0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243) [ 0.000000] ssb: chipcommon status is 0x0 [ 0.000000] ssb: Initializing MIPS core... [ 0.000000] ssb: set_irq: core 0x0806, irq 4 => 4 [ 0.000000] ssb: set_irq: core 0x0806, irq 5 => 5 [ 0.000000] ssb: set_irq: core 0x0808, irq 6 => 2 [ 0.000000] ssb: set_irq: core 0x0804, irq 2 => 6 [ 0.000000] ssb: after irq reconfiguration [ 0.000000] ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I [ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I [ 0.000000] ssb: core 0x0806, irq : 2(S) 3 4 5* 6 D I [ 0.000000] ssb: core 0x0808, irq : 2(S)* 3 4 5 6 D I [ 0.000000] ssb: core 0x0804, irq : 2(S) 3 4 5 6* D I [ 0.000000] ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I [ 0.000000] ssb: core 0x0807, irq : 2(S)* 3 4 5 6 D I [ 0.000000] ssb: core 0x080b, irq : 2(S)* 3 4 5 6 D I [ 0.000000] ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I* [ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000 [ 0.000000] MIPS: machine is Linksys WRT150N V1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 01000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x00ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x00ffffff] [ 0.000000] On node 0 totalpages: 4096 [ 0.000000] free_area_init_node: node 0, pgdat 802dcbe0, node_mem_map 8035b000 [ 0.000000] Normal zone: 32 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 4096 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes) [ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Memory: 12748k/16384k available (2416k kernel code, 3636k reserved, 592k data, 184k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.070000] Calibrating delay loop... 262.96 BogoMIPS (lpj=1314816) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.070000] NET: Registered protocol family 16 [ 0.110000] bio: create slab <bio-0> at 0 [ 0.120000] Switching to clocksource MIPS [ 0.130000] ssb: PCIcore in host mode found [ 0.430000] PCI host bridge to bus 0000:00 [ 0.430000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff] [ 0.430000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff] [ 0.430000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.430000] pci 0000:00:00.0: [14e4:4704] type 00 class 0x060000 [ 0.430000] ssb: PCI: Fixing up bridge 0000:00:00.0 [ 0.430000] pci 0000:00:00.0: setting latency timer to 64 [ 0.430000] ssb: PCI: Fixing up device 0000:00:00.0 [ 0.430000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168 [ 0.430000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff] [ 0.430000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref] [ 0.430000] pci 0000:00:01.0: [14e4:4321] type 00 class 0x028000 [ 0.430000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff] [ 0.430000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.430000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff] [ 0.440000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.440000] ssb: PCI: Fixing up device 0000:00:01.0 [ 0.440000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64 [ 0.480000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01 [ 0.480000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x12, vendor 0x4243) [ 0.480000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0B, vendor 0x4243) [ 0.480000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x02, vendor 0x4243) [ 0.480000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243) [ 0.480000] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243) [ 0.520000] ssb: chipcommon status is 0x0 [ 0.520000] ssb: SPROM offset is 0x1000 [ 0.540000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22 [ 0.540000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22 [ 0.540000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22 [ 0.690000] ssb: Using SPROM revision 4 provided by platform [ 0.730000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.730000] NET: Registered protocol family 2 [ 0.730000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.730000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.740000] TCP: Hash tables configured (established 512 bind 512) [ 0.740000] TCP: reno registered [ 0.740000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.740000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.740000] NET: Registered protocol family 1 [ 0.740000] PCI: CLS 0 bytes, default 16 [ 0.750000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.750000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.750000] msgmni has been set to 24 [ 0.750000] io scheduler noop registered [ 0.750000] io scheduler deadline registered (default) [ 0.750000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.790000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A [ 1.140000] console [ttyS0] enabled [ 1.160000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A [ 1.180000] physmap platform flash device: 02000001 at 1c000000 [ 1.180000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x0022f6 [ 1.200000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0xc00000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0x1400000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0 [ 1.200000] physmap-flash.0: Found an alias at 0x1c00000 for the chip at 0x0 [ 1.200000] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.200000] Amd/Fujitsu Extended Query version 1.1. [ 1.210000] physmap-flash.0: Swapping erase regions for top-boot CFI table. [ 1.210000] number of CFI chips: 1 [ 1.220000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0 [ 1.230000] Creating 6 MTD partitions on "physmap-flash.0": [ 1.230000] 0x000000000000-0x000000040000 : "boot" [ 1.240000] 0x000000040000-0x0000003f0000 : "firmware" [ 1.250000] 0x00000004001c-0x000000040960 : "loader" [ 1.260000] 0x000000040960-0x000000149c00 : "linux" [ 1.270000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.290000] 0x000000149c00-0x0000003f0000 : "rootfs" [ 1.290000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.310000] mtd: device 4 (rootfs) set to be root filesystem [ 1.310000] mtd: partition "rootfs_data" created automatically, ofs=0x320000, len=0xd0000 [ 1.320000] 0x000000320000-0x0000003f0000 : "rootfs_data" [ 1.330000] 0x0000003f0000-0x000000400000 : "nvram" [ 1.360000] libphy: Fixed MDIO Bus: probed [ 1.360000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 1.370000] GPIO_WDT: failed to register misc device [ 1.380000] TCP: cubic registered [ 1.380000] NET: Registered protocol family 17 [ 1.390000] Bridge firewalling registered [ 1.390000] can: controller area network core (rev 20120528 abi 9) [ 1.400000] NET: Registered protocol family 29 [ 1.400000] 8021q: 802.1Q VLAN Support v1.8 [ 1.420000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.430000] Freeing unused kernel memory: 184K (802f2000 - 80320000) [ 6.390000] pps_core: LinuxPPS API ver. 1 registered [ 6.390000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 6.410000] PTP clock support registered [ 6.420000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0 [ 6.440000] libphy: b44_eth_mii: probed [ 6.460000] b53_common: found switch: BCM5325, rev 0 [ 6.460000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e) [ 6.470000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1c:10:19:a4:e6 [ 6.490000] libphy: b44_eth_mii: probed [ 6.490000] b44 ssb0:1: could not find PHY at 4, use fixed one [ 6.500000] b44 ssb0:1: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:00) [ 6.500000] b44 ssb0:1 eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:88:88:88:00:2a [ 6.520000] bgmac: Broadcom 47xx GBit MAC driver loaded [ 7.150000] b44 ssb0:0 eth0: Link is up at 100 Mbps, half duplex [ 7.160000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX [ 11.940000] b44 ssb0:0 eth0: powering down PHY [ 20.210000] NET: Registered protocol family 10 [ 20.240000] nf_conntrack version 0.5.0 (202 buckets, 808 max) [ 20.260000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.310000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 [ 20.320000] Backport generated by backports.git backports-20130802-0-gdb67a3f [ 20.340000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.440000] xt_time: kernel timezone is -0000 [ 20.490000] cfg80211: Calling CRDA to update world regulatory domain [ 20.500000] cfg80211: World regulatory domain updated: [ 20.500000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.510000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.520000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.520000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 20.540000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 20.550000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 22.910000] PPP generic driver version 2.4.2 [ 23.410000] NET: Registered protocol family 24 [ 24.080000] b43-phy0: Broadcom 4321 WLAN found (core revision 11) [ 25.060000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1 [ 25.990000] Broadcom 43xx driver loaded [ Features: PNL ] [ 26.560000] Broadcom 43xx-legacy driver loaded [ Features: PLD ] [ 26.590000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 40.550000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 40.590000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 40.590000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 49.200000] jffs2: notice: (621) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 54.270000] b44 ssb0:0 eth0: Link is up at 100 Mbps, half duplex [ 54.270000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX [ 54.290000] device eth0 entered promiscuous mode [ 54.310000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 54.440000] b44 ssb0:1 eth1: Link is up at 100 Mbps, half duplex [ 54.450000] b44 ssb0:1 eth1: Flow control is off for TX and off for RX [ 55.320000] br-lan: port 1(eth0) entered forwarding state [ 55.320000] br-lan: port 1(eth0) entered forwarding state [ 55.330000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 55.710000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 57.320000] br-lan: port 1(eth0) entered forwarding state An account of flashing OpenWrt to a WRT150N The router is a LinkSys WRT150N. No version is shown on the device. The serial number begins CQ6.. Did a 30/30/30 reset Joined a laptop to the router with a patch cable Configured the laptop as 192.168.1.2 Browsed to 192.168.1.1 Username: admin, Password: admin Navigated to Administration, Firmware Upgrade legacy Uploaded http://downloads.openwrt.org/kamikaze/8.09.2/brcm-2.4/openwrt-wrt150n-squashfs.bin NOTE: This above image is old → please visit http://downloads.openwrt.org/releases/18.06.4/targets/brcm47xx/legacy/ and use the image builder to generate something smaller than ~3623KB ... After a short while, nmap -F 192.168.1.1 showed: PORT STATE SERVICE 22/tcp open ssh 23/tcp open telnet 53/tcp open domain 80/tcp open http image.conversion route add default gw 192.168.1.2 # assuming .2 is your laptop vi /etc/resolv.conf # to tell OpenWrt where the DNS recursor is opkg update opkg install kmod-brcm-wl-mimo reboot Why you should use brcm-2.4 The brcm47xx flavour of 10.03.1 will yield: b43-phy0: Broadcom 4321 WLAN found (core revision 11) b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 5, Type 4, Revision 1) b43: probe of ssb1:0 failed with error -122 ..in the kernel log and no wireless interface. Hardware /proc/cpuinfo: system type : Broadcom BCM4704 chip rev 9 processor : 0 cpu model : BCM3302 V0.6 BogoMIPS : 263.78 wait instruction : no microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no VCED exceptions : not available VCEI exceptions : not available /proc/pci: PCI devices found: Bus 0, device 0, function 0: Class 0501: PCI device 14e4:0800 (rev 9). IRQ 3. Non-prefetchable 32 bit memory at 0x18000000 [0x18000fff]. Non-prefetchable 32 bit memory at 0x1fc00000 [0x1fffffff]. Non-prefetchable 32 bit memory at 0x1c000000 [0x1dffffff]. Non-prefetchable 32 bit memory at 0x1a000000 [0x1bffffff]. Bus 0, device 1, function 0: Class 0200: PCI device 14e4:4713 (rev 9). IRQ 4. Master Capable. Latency=64. Non-prefetchable 32 bit memory at 0x18001000 [0x18001fff]. Bus 0, device 2, function 0: Class 0200: PCI device 14e4:4713 (rev 9). IRQ 5. Master Capable. Latency=64. Non-prefetchable 32 bit memory at 0x18002000 [0x18002fff]. Bus 0, device 3, function 0: Class 0c03: PCI device 14e4:4715 (rev 9). IRQ 6. Non-prefetchable 32 bit memory at 0x18003000 [0x18003fff]. Bus 0, device 4, function 0: Class 0604: PCI device 14e4:0804 (rev 9). IRQ 2. Non-prefetchable 32 bit memory at 0x18004000 [0x18004fff]. Non-prefetchable 32 bit memory at 0x8000000 [0xfffffff]. Bus 0, device 5, function 0: Class 0b30: PCI device 14e4:0816 (rev 9). IRQ 2. Non-prefetchable 32 bit memory at 0x18005000 [0x18005fff]. Bus 0, device 6, function 0: Class 0703: PCI device 14e4:4712 (rev 9). IRQ 2. Non-prefetchable 32 bit memory at 0x18006000 [0x18006fff]. Bus 0, device 7, function 0: Class 1000: PCI device 14e4:4718 (rev 9). IRQ 2. Non-prefetchable 32 bit memory at 0x18007000 [0x18007fff]. Bus 0, device 8, function 0: Class 0500: PCI device 14e4:080f (rev 9). IRQ 3. Non-prefetchable 32 bit memory at 0x18008000 [0x18008fff]. Non-prefetchable 32 bit memory at 0x0 [0x7ffffff]. Non-prefetchable 32 bit memory at 0x10000000 [0x17ffffff]. Non-prefetchable 32 bit memory at 0x80000000 [0x9fffffff]. Bus 1, device 0, function 0: Class 0600: PCI device 14e4:4704 (rev 9). IRQ 2. Master Capable. Latency=64. Non-prefetchable 32 bit memory at 0x40000000 [0x40001fff]. Prefetchable 32 bit memory at 0x0 [0x7ffffff]. Bus 1, device 1, function 0: Class 0280: PCI device 14e4:4321 (rev 1). IRQ 2. Master Capable. Latency=64. Non-prefetchable 32 bit memory at 0x40004000 [0x40007fff]. Tags How to add tags bcm47xx, bcm4704, 4Flash, 16RAM This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies bcm47xx bcm4704 4Flash 16RAM Last modified: 2019/10/11 00:08by someothertime