JCG JHR-N926R

U-Boot 1.1.3 (Aug 10 2012 - 17:30:27) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 config usb.... Set info->start[0]=BF000000 flash_protect ON: from 0xBF000000 to 0xBF01F3DF flash_protect ON: from 0xBF030000 to 0xBF030FFF *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.6.0.0 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: NOR Flash Date:Aug 10 2012 Time:17:30:27 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### estimate memory size =32 Mbytes ## Booting image at bf050000 ... Image Name: Linux Kernel Image Created: 2012-08-10 9:30:21 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3564871 Bytes = 3.4 MB Load Address: 80000000 Entry Point: 80292000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80292000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (root@devsrv2) (gcc version 3.4.2) #593 Fri Aug 10 17:30:18 CST 2012 The CPU frequency set to 384 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = d0808068, status = 11000000 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00177000(1536000) CPU frequency 384.00 MHz Using 192.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29644k/32768k available (2339k kernel code, 3124k reserved, 288k data, 116k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered ralink flash device: 0x1000000 at 0x1f000000 Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 7 MTD partitions on "Ralink SoC physically mapped flash": 0x00000000-0x00400000 : "ALL" 0x00000000-0x00030000 : "Bootloader" 0x00030000-0x00040000 : "Config" 0x00040000-0x00050000 : "Factory" 0x00050000-0x00121587 : "Kernel" mtd: partition "Kernel" doesn't end on an erase block -- force read-only 0x00121587-0x01000000 : "RootFS" mtd: partition "RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x2dea79 mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only 0x00050000-0x01000000 : "Kernel_RootFS" mtd: partition "Kernel_RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x3b0000 squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) Ralink gpio driver initialized HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 253 eth2 mii.o query= phy_id:0, address:1 retval:7849 Ralink APSoC Ethernet Driver Initilization. v2.1 256 rx/tx descriptors allocated, mtu = 1500! MAC_ADRH -- : 0x000000e0 MAC_ADRL -- : 0x4b9bd54f PROC INIT OK! IMQ starting with 4 devices... IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V0.17 PPTP driver version 0.8.1 block2mtd: version $Revision: 1.1.1.1 $ GACT probability NOT on netem: version 1.2 u32 classifier Performance counters on input device check on Actions configured nf_conntrack version 0.5.0 (256 buckets, 2048 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone ipt_time loading TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 116k freed init started: BusyBox v1.12.1 (2012-08-10 17:29:18 CST) Bad inittab entry at line 2 Algorithmics/MIPS FPU Emulator v1.5 devpts: called with bogus options mount: mounting none on /proc/bus/usb failed: No such file or directory ------------------------------------------------- Password for 'admin' changed phy_tx_ring = 0x013f4000, tx_ring = 0xa13f4000 phy_rx_ring0 = 0x013f5000, rx_ring0 = 0xa13f5000 MAC_ADRH -- : 0x000000e0 MAC_ADRL -- : 0x4b9bd54f CDMA_CSG_CFG = 81000007 GDMA1_FWD_CFG = 1710000 switchTableDel: done! switchTableDel: done! switchTableDel: done! switchTableDel: done! switchTableDel: done! eth2 mii.o query= phy_id:1, address:4 retval:5e1 eth2 mii.o query= phy_id:1, address:0 retval:3100 eth2 mii.o query= phy_id:1, address:5 retval:0 eth2.2: dev_set_promiscuity(master, 1) device eth2 entered promiscuous mode device eth2.2 entered promiscuous mode eth2 mii.o query= phy_id:1, address:4 retval:5e1 eth2 mii.o query= phy_id:1, address:0 retval:3100 eth2 mii.o query= phy_id:1, address:5 retval:0 eth2.3: dev_set_promiscuity(master, 1) device eth2.3 entered promiscuous mode eth2 mii.o query= phy_id:1, address:4 retval:5e1 eth2 mii.o query= phy_id:1, address:0 retval:3100 eth2 mii.o query= phy_id:1, address:5 retval:0 eth2.4: dev_set_promiscuity(master, 1) device eth2.4 entered promiscuous mode eth2 mii.o query= phy_id:1, address:4 retval:5e1 eth2 mii.o query= phy_id:1, address:0 retval:3100 eth2 mii.o query= phy_id:1, address:5 retval:0 eth2.5: dev_set_promiscuity(master, 1) device eth2.5 entered promiscuous mode rt2860v2_ap: module license 'unspecified' taints kernel. === pAd = c004c000, size = 805344 === <-- RTMPAllocAdapterBlock, Status=0 RX DESC a1df6000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff ff 00 00 01 Main bssid = 00:e0:4b:9b:d5:50 <==== rt28xx_init, Status=0 0x1300 = 00064380 device ra0 entered promiscuous mode ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/ br0: port 5(ra0) entering learning state br0: port 4(eth2.5) entering learning state br0: port 3(eth2.4) entering learning state br0: port 2(eth2.3) entering learning state br0: port 1(eth2.2) entering learning state ***** g_wl_interface = ra0 ****** eth2.1: Setting MAC address to 00 e0 4b 9b d5 4e. write offset 0x60, value 0x3dc webs: Listening for HTTP requests at address 192.168.1.1 WAN link UP -> DOWN RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory

U-Boot 1.1.3 (Aug 10 2012 - 17:30:27) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fac000 config usb.... ****************************** Software System Reset Occurred ****************************** Set info->start[0]=BF000000 flash_protect ON: from 0xBF000000 to 0xBF01F3DF flash_protect ON: from 0xBF030000 to 0xBF030FFF *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 3.6.0.0 -------------------------------------------- ASIC 3052_MP2 (Port5<->None) DRAM component: 256 Mbits SDR DRAM bus: 16 bit Total memory: 32 MBytes Flash component: NOR Flash Date:Aug 10 2012 Time:17:30:27 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### estimate memory size =32 Mbytes ## Booting image at bf050000 ... Image Name: MIPS LEDE Linux-4.4.92 Created: 2017-10-17 17:46:20 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1160328 Bytes = 1.1 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 32 Starting kernel ... [ 0.000000] Linux version 4.4.92 (buildbot@debian8) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3556-46e29bd) ) #0 Mon Oct 16 15:21:43 2017 [ 0.000000] SoC Type: Ralink RT3052 id:1 rev:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc) [ 0.000000] MIPS: machine is JCG JHR-N926R [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000001ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 28612K/32768K available (2892K kernel code, 132K rwdata, 356K rodata, 196K init, 196K bss, 4156K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 384MHz [ 0.000000] clocksource_probe: no matching clocksources found [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9954481493 ns [ 0.000015] sched_clock: 32 bits at 192MHz, resolution 5ns, wraps every 11184811005ns [ 0.015719] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952) [ 0.100994] pid_max: default: 32768 minimum: 301 [ 0.110470] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.123589] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.146404] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.166018] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.178259] pinctrl core: initialized pinctrl subsystem [ 0.191062] NET: Registered protocol family 16 [ 0.208038] Can't analyze schedule() prologue at 8000acdc [ 0.246969] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.258113] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.272954] clocksource: Switched to clocksource MIPS [ 0.285216] NET: Registered protocol family 2 [ 0.295779] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.309700] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.322321] TCP: Hash tables configured (established 1024 bind 1024) [ 0.335212] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.346871] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.359856] NET: Registered protocol family 1 [ 0.378507] rt-timer 10000100.timer: maximum frequency is 3906Hz [ 0.391996] Crashlog allocated RAM at address 0x1f00000 [ 0.437699] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.449312] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.474667] io scheduler noop registered [ 0.482345] io scheduler deadline registered (default) [ 0.494182] gpio-export gpio_export: 3 gpio(s) exported [ 0.504998] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.524216] console [ttyS0] disabled [ 0.531274] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 8000000) is a Palmchip BK-3103 [ 0.551152] console [ttyS0] enabled [ 0.551152] console [ttyS0] enabled [ 0.565065] bootconsole [early0] disabled [ 0.565065] bootconsole [early0] disabled [ 0.583061] 1f000000.cfi: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001a00 [ 0.603345] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.613768] Amd/Fujitsu Extended Query version 1.3. [ 0.624001] number of CFI chips: 1 [ 0.642341] 4 ofpart partitions found on MTD device 1f000000.cfi [ 0.654567] Creating 4 MTD partitions on "1f000000.cfi": [ 0.665330] 0x000000000000-0x000000030000 : "u-boot" [ 0.678518] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.693086] 0x000000040000-0x000000050000 : "factory" [ 0.706996] 0x000000050000-0x000000400000 : "firmware" [ 0.722601] 2 uimage-fw partitions found on MTD device firmware [ 0.734686] 0x000000050000-0x00000016b4c8 : "kernel" [ 0.748229] 0x00000016b4c8-0x000000400000 : "rootfs" [ 0.761963] mtd: device 5 (rootfs) set to be root filesystem [ 0.773552] 1 squashfs-split partitions found on MTD device rootfs [ 0.786082] 0x000000380000-0x000000400000 : "rootfs_data" [ 0.804896] rt3050-esw 10110000.esw: link changed 0x02 [ 0.819812] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.837489] rt2880_wdt 10000120.watchdog: Initialized [ 0.850127] NET: Registered protocol family 10 [ 0.866449] NET: Registered protocol family 17 [ 0.875739] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.901254] 8021q: 802.1Q VLAN Support v1.8 [ 0.918918] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.935580] Freeing unused kernel memory: 196K [ 2.035611] init: Console is alive [ 2.043121] init: - watchdog - [ 2.825392] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.963820] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.989303] init: - preinit - [ 4.049109] 8021q: adding VLAN 0 to HW filter on device eth0 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to [ 4.301029] random: procd: uninitialized urandom read (4 bytes read, 7 bits of entropy available) select the debug level [ 7.543808] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 7.565751] urandom-seed: Seed file not found (/etc/urandom.seed) [ 7.749745] procd: - early - [ 7.756049] procd: - watchdog - [ 8.403219] procd: - watchdog - [ 8.410287] procd: - ubus - [ 8.536923] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.669492] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.688731] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.707191] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.726365] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.744774] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.763633] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.782410] random: ubusd: uninitialized urandom read (4 bytes read, 14 bits of entropy available) [ 8.801723] procd: - init - Please press Enter to activate this console. [ 9.299193] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.322748] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.356043] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 9.372296] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 9.394722] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.419993] nf_conntrack version 0.5.0 (450 buckets, 1800 max) [ 9.493112] xt_time: kernel timezone is -0000 [ 9.603339] PPP generic driver version 2.4.2 [ 9.617244] NET: Registered protocol family 24 [ 9.670888] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 9.685628] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 2872, rev 0200 detected [ 9.701315] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected [ 9.849857] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.241345] random: jshn: uninitialized urandom read (4 bytes read, 18 bits of entropy available) [ 21.087178] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 21.213003] jffs2_build_filesystem(): unlocking the mtd device... done. [ 21.226411] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 25.024251] 8021q: adding VLAN 0 to HW filter on device eth0 [ 25.073271] device eth0.1 entered promiscuous mode [ 25.083065] device eth0 entered promiscuous mode [ 25.165691] br-lan: port 1(eth0.1) entered forwarding state [ 25.177128] br-lan: port 1(eth0.1) entered forwarding state [ 25.716868] done. [ 25.720817] jffs2: notice: (809) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 27.172996] br-lan: port 1(eth0.1) entered forwarding state [ 76.733048] random: nonblocking pool is initialized BusyBox v1.25.1 () built-in shell (ash) _________ / /\ _ ___ ___ ___ / LE / \ | | | __| \| __| / DE / \ | |__| _|| |) | _| /________/ LE \ |____|___|___/|___| lede-project.org \ \ DE / \ LE \ / ----------------------------------------------------------- \ DE \ / Reboot (17.01.4, r3560-79f57e422d) \________\/ ----------------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@LEDE:/# free total used free shared buffers cached Mem: 28808 17120 11688 356 1888 6120 -/+ buffers/cache: 9112 19696 Swap: 0 0 0 root@LEDE:/# df -m Filesystem 1M-blocks Used Available Use% Mounted on /dev/root 2 2 0 100% /rom tmpfs 14 0 14 2% /tmp tmpfs 14 0 14 0% /tmp/root tmpfs 1 0 1 0% /dev /dev/mtdblock6 1 0 0 41% /overlay overlayfs:/overlay 1 0 0 41% / root@LEDE:/# cat /proc/mtd dev: size erasesize name mtd0: 00030000 00010000 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "factory" mtd3: 003b0000 00010000 "firmware" mtd4: 0011b4c8 00010000 "kernel" mtd5: 00294b38 00010000 "rootfs" mtd6: 00080000 00010000 "rootfs_data" root@LEDE:/# root@LEDE:/# ps PID USER VSZ STAT COMMAND 1 root 1528 S /sbin/procd 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW< [kworker/0:0H] 6 root 0 SW [kworker/u2:0] 7 root 0 SW [kworker/u2:1] 36 root 0 SW [kworker/u2:2] 37 root 0 SW< [writeback] 70 root 0 SW< [crypto] 72 root 0 SW< [bioset] 73 root 0 SW< [kblockd] 75 root 0 SW [kworker/0:1] 106 root 0 SW [kswapd0] 143 root 0 SW [fsnotify_mark] 201 root 0 SW< [bioset] 206 root 0 SW< [bioset] 211 root 0 SW< [bioset] 216 root 0 SW< [bioset] 221 root 0 SW< [bioset] 226 root 0 SW< [bioset] 231 root 0 SW< [bioset] 249 root 0 SW< [ipv6_addrconf] 255 root 0 SW< [deferwq] 257 root 0 SW< [kworker/0:1H] 372 root 1176 S /sbin/ubusd 373 root 1188 S /bin/ash --login 442 root 0 SW< [cfg80211] 682 root 1224 S /sbin/logd -S 64 691 root 1440 S /sbin/rpcd 738 root 1632 S /sbin/netifd 760 root 1416 S /usr/sbin/odhcpd 805 root 1528 S /usr/sbin/uhttpd -f -h /www -r LEDE -x /cgi-bin -u / 849 root 0 SWN [jffs2_gcd_mtd6] 876 root 1184 S udhcpc -p /var/run/udhcpc-eth0.2.pid -s /lib/netifd/ 877 root 1016 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0. 929 root 0 SW [kworker/0:2] 998 root 1184 S /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0. 1009 dnsmasq 1048 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg02411c 1047 root 1060 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 1066 root 1184 R ps root@LEDE:/# ifconfig br-lan Link encap:Ethernet HWaddr 00:E0:4B:9B:D5:4E inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fd91:fd87:f7b0::1/60 Scope:Global inet6 addr: fe80::2e0:4bff:fe9b:d54e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:209 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:20681 (20.1 KiB) TX bytes:77226 (75.4 KiB) eth0 Link encap:Ethernet HWaddr 00:E0:4B:9B:D5:4E inet6 addr: fe80::2e0:4bff:fe9b:d54e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:220 errors:0 dropped:0 overruns:0 frame:0 TX packets:307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:25259 (24.6 KiB) TX bytes:110846 (108.2 KiB) Interrupt:5 eth0.1 Link encap:Ethernet HWaddr 00:E0:4B:9B:D5:4E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:220 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21299 (20.7 KiB) TX bytes:77226 (75.4 KiB) eth0.2 Link encap:Ethernet HWaddr 00:E0:4B:9B:D5:4F inet6 addr: fe80::2e0:4bff:fe9b:d54f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:96 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:28873 (28.1 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:184 errors:0 dropped:0 overruns:0 frame:0 TX packets:184 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:12016 (11.7 KiB) TX bytes:12016 (11.7 KiB) root@LEDE:/# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 br-lan