GL.iNet GL-AP1300

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The AP1300 (Cirrus) is a wireless access point with two Ethernet ports. The WAN port has 802.1af PoE, and there are addons for bluetooth or cellphone radios. It ships with Chaos Calmer [15.05], and is designed exclusively for OpenWrt. It comes with two versions, GL-AP1300LTE is a 4G LTE router with a CAT4 or CAT6 modem, and GL-AP1300 is the standard version. Both of them have built-in PoE and watchdog features.

GL-AP1300: GL-AP1300 GL-AP1300LTE: GL-AP1300LTE

  • 400Mbps (2.4G) + 867Mbps (5G) Combined Wi-Fi Speed
  • Supports MU-MIMO
  • 2 Gigabit Ports with RJ45 Interface
  • PoE Power Supply
  • Built-in Watchdog
  • built-in nano SIM card slot
  • built-in mini PCIe interchangeable module
ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
GL-AP1300Qualcomm IPQ4018717128NAND, 4256Qualcomm IPQ4018b/g/na/n/ac-2--

Note: Only GL-AP1300LTE version has a 4G LTE built-in modem

dev:    size   erasesize  name
mtd0: 00040000 00010000 "SBL1"
mtd1: 00020000 00010000 "MIBIB"
mtd2: 00060000 00010000 "QSEE"
mtd3: 00010000 00010000 "CDT"
mtd4: 00010000 00010000 "DDRPARAMS"
mtd5: 00010000 00010000 "APPSBLENV"
mtd6: 00080000 00010000 "APPSBL"
mtd7: 00010000 00010000 "ART"
mtd8: 08000000 00020000 "ubi"
  • Browse to http://192.168.8.1/#/upgrade GL.iNet Web Upgrade URL
  • Upload image file for sysupgrade
  • Choose whether to keep the configuration according to your needs, the default is to keep the configuration
  • Click install
  • Wait until fully rebooted
  • Browse to http://192.168.8.1/cgi-bin/luci/admin/system/flash LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait until fully rebooted

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line.

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

  • Login as root via SSH on 192.168.8.1, then enter the following commands:
cd /tmp
wget http://download.gl-inet.com/firmware/ap1300/release/qsdk-ap1300-3.203-0701.img
sysupgrade /tmp/qsdk-ap1300-3.203-0701.img

On devices with a physical reset button, OpenWrt can be reset to default settings without serial or SSH access.

  1. Power on the device and wait for the status led to stop flashing (or go into failsafe mode, as described above).
  2. Press and hold the reset button for 10 seconds.
  3. Release the reset button.

The device will do a hard factory reset (see below) and then reboot. This operation can be slow on some devices, so wait a few minutes before connecting again.

If you want a clean slate, there’s no need to flash again; just enter the following commands. Your device's settings will be reset to defaults like when OpenWrt was first installed.

Issuing “firstboot” or “jffs2reset” command will attempt to delete all files from the jffs2 overlay partition. Note that this “soft reset” is performed with file system actions, so in some cases it is not enough.

firstboot && reboot now

Note: If the commands above (all on one line) don't work, try those commands on separate lines in the terminal.

Note: for most routers, “firstboot” actually just issues a “jffs2reset” command, so there is not much difference compared to the “hard reset” advice below.

Note: if you're issuing this command inside a bash script, remember to add the option -y to force firstboot:

firstboot -y && reboot now

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Base on the OpenWrt firmware, the default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
eth0 LAN port 192.168.1.1/24
eth1 WAN port DHCP client
wlan0 WiFi 2.4G Disable
wlan1 WiFi 5G Disable

Base on the OEM(GL.iNet) firmware, the default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.8.1/24
eth0 WAN port DHCP client
eth1 LAN port 192.168.8.1/24
ath0 WiFi 2.4G GL-AP1300-xxx
ath1 WiFi 5G GL-AP1300-xxx-5G

hardware.button on howto use and configure the hardware button(s).

The GL.iNet AP1300 has the following buttons:

BUTTON Event
Reset reset
General
Brand GL.iNet
Model GL-AP1300
Versions
Device Type WiFi AP
Availability Available 2020
Comments - general The 4G LTE version with external antennas is called GL-AP1300LTE
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b9389186b012e5bd99ea6523b8220aaee6ca0085
Supported Since Release 21.02.0
Supported Current Release 22.03.2
Unsupported
Hardware
Bootloader U-Boot
Target ipq40xx
System-On-Chip Qualcomm IPQ4018
CPU MHz 717
Flash MB 128NAND, 4
RAM MB 256
Network
Ethernet 100M ports -
Ethernet Gbit ports 2
Switch Qualcomm Atheros QCA8075
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware Qualcomm IPQ4018
Detachable Antennas -
Comments - WLAN MU-MIMO
Interfaces
USB ports -
SATA ports -
Serial Yes
JTAG ¿
Comments - USB & SATA ports
Misc
LED count 2
Button count 1
Power supply 12 VDC, 2.0 A, PoE 802.3at
Links
Forum Topic URL
WikiDevi URL
OEM device homepage URL https://www.gl-inet.com/products/gl-ap1300/
Firmware OEM Stock URL https://dl.gl-inet.com/?model=ap1300
Firmware OpenWrt Install URL https://downloads.openwrt.org/releases/22.03.2/targets/ipq40xx/generic/openwrt-22.03.2-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/releases/22.03.2/targets/ipq40xx/generic/openwrt-22.03.2-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-sysupgrade.bin
Edit the underlying data View/Edit data

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

  • To remove the cover and open the device, do a/b/c

Main PCB:
Check here: https://docs.gl-inet.com/en/3/specification/gl-ap1300/

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for GL.iNet GL-AP1300
EXAMPLE 115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.60 (han@glinet) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 6404588+r49254) ) #1 SMP PREEMPT Wed Mar 24 18:00:04 CST 2021 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 61440 [ 0.000000] free_area_init_node: node 0, pgdat c0b05740, node_mem_map cfdf9000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 61440 pages, LIFO batch:15 [ 0.000000] PERCPU: Embedded 11 pages/cpu @cfdbe000 s14400 r8192 d22464 u45056 [ 0.000000] pcpu-alloc: s14400 r8192 d22464 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 60928 [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait clk_ignore_unused [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 234576K/245760K available (5267K kernel code, 302K rwdata, 1736K rodata, 1024K init, 252K bss, 11184K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc09d6c00 (7995 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB) [ 0.000000] .data : 0xc0b00000 - 0xc0b4bb68 ( 303 kB) [ 0.000000] .bss : 0xc0b4e000 - 0xc0b8d32c ( 253 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000023] Switching to timer-based delay loop, resolution 20ns [ 0.000232] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000249] pid_max: default: 32768 minimum: 301 [ 0.000364] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000378] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000992] CPU: Testing write buffer coherency: ok [ 0.001325] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001415] Setting up static identity map for 0x80300000 - 0x80300058 [ 0.052886] MSM Memory Dump base table set up [ 0.052927] MSM Memory Dump apps data table set up [ 0.090573] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.120610] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.150677] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.150766] Brought up 4 CPUs [ 0.150796] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.150804] CPU: All CPU(s) started in SVC mode. [ 0.157225] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.157631] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.157666] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.157935] pinctrl core: initialized pinctrl subsystem [ 0.159348] NET: Registered protocol family 16 [ 0.161020] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.190417] cpuidle: using governor ladder [ 0.220445] cpuidle: using governor menu [ 0.232570] gpiochip_add: registered GPIOs 0 to 99 on device: 1000000.pinctrl [ 0.232595] GPIO chip 1000000.pinctrl: created GPIO range 0->99 ==> 1000000.pinctrl PIN 0->99 [ 0.233833] Read of property:soc_version_minor from node failed [ 0.233845] Read of property:soc_version_major from node failed [ 0.233853] Read of property:cpu_type from node failed [ 0.233865] CPU: unavail, SoC Version: 4294967295.4294967295 [ 0.234406] IPC logging disabled [ 0.234415] IPC logging disabled [ 0.234421] IPC logging disabled [ 0.234427] IPC logging disabled [ 0.234433] IPC logging disabled [ 0.234693] sps:sps is ready. [ 0.264063] Advanced Linux Sound Architecture Driver Initialized. [ 0.265139] clocksource: Switched to clocksource arch_sys_counter [ 0.266783] NET: Registered protocol family 2 [ 0.267772] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.267820] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.267868] TCP: Hash tables configured (established 2048 bind 2048) [ 0.267935] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.267969] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.268214] NET: Registered protocol family 1 [ 0.268280] PCI: CLS 0 bytes, default 64 [ 0.279022] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.279049] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.283860] Key type asymmetric registered [ 0.283884] Asymmetric key parser 'x509' registered [ 0.283939] io scheduler noop registered [ 0.283959] io scheduler deadline registered (default) [ 0.288298] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.288367] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.288437] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.288495] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.288830] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set [ 0.289664] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.289715] msm_serial 78af000.serial: uartclk = 1843200 [ 0.289767] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.289798] msm_serial: console setup on port #0 [ 0.819169] console [ttyMSM0] enabled [ 0.824230] msm_serial: driver initialized [ 0.827703] msm_serial_hsl_init: driver initialized [ 0.844949] brd: module loaded [ 0.845912] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.847096] of_get_named_gpiod_flags: parsed 'cs-gpios' property of node '/soc/spi@78b5000[0]' - status (0) [ 0.847118] of_get_named_gpiod_flags: parsed 'cs-gpios' property of node '/soc/spi@78b5000[1]' - status (0) [ 0.849048] m25p80 spi0.0: found w25q32, expected n25q128a11 [ 0.854111] m25p80 spi0.0: w25q32 (4096 Kbytes) [ 0.859848] 8 ofpart partitions found on MTD device spi0.0 [ 0.863999] Creating 8 MTD partitions on "spi0.0": [ 0.869591] 0x000000000000-0x000000040000 : "0:SBL1" [ 0.875580] 0x000000040000-0x000000060000 : "0:MIBIB" [ 0.880578] 0x000000060000-0x0000000c0000 : "0:QSEE" [ 0.885570] 0x0000000c0000-0x0000000d0000 : "0:CDT" [ 0.890549] 0x0000000d0000-0x0000000e0000 : "0:DDRPARAMS" [ 0.895248] 0x0000000e0000-0x0000000f0000 : "0:APPSBLENV" [ 0.900777] 0x0000000f0000-0x000000170000 : "0:APPSBL" [ 0.906098] 0x000000170000-0x000000180000 : "0:ART" [ 0.911793] libphy: Fixed MDIO Bus: probed [ 0.915409] of_get_named_gpiod_flags: parsed 'phy-reset-gpio' property of node '/soc/mdio@90000[0]' - status (0) [ 1.135545] of_get_named_gpiod_flags: can't parse 'phy-reset-gpio' property of node '/soc/mdio@90000[1]' [ 1.135565] qca-mdio 90000.mdio: Could not find phy-reset-gpio [ 1.135762] libphy: qca_mdio: probed [ 1.142547] qca-mdio 90000.mdio: qca-mdio driver was registered [ 1.144112] Unable to create IPC log context! [ 1.149973] i2c /dev entries driver [ 1.156068] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com [ 1.158245] sdhci: Secure Digital Host Controller Interface driver [ 1.166187] sdhci: Copyright(c) Pierre Ossman [ 1.172150] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.183153] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xb1 [ 1.183185] nand: GigaDevice GD5F1GQ1UC 128MiB 3.3V [ 1.188679] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128 [ 1.193251] Scanning device for bad blocks [ 1.371640] random: nonblocking pool is initialized [ 2.091468] Bad eraseblock 1023 at 0x000007fe0000 [ 2.091513] 1 ofpart partitions found on MTD device spi0.1 [ 2.095175] Creating 1 MTD partitions on "spi0.1": [ 2.100535] 0x000000000000-0x000008000000 : "rootfs" [ 2.107576] mtd: device 8 (rootfs) set to be root filesystem [ 2.113647] mtdsplit: no squashfs found in "rootfs" [ 2.116469] [ 2.116469] Version Rollback Feature Disabled [ 2.125190] NET: Registered protocol family 10 [ 2.137673] NET: Registered protocol family 17 [ 2.137765] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.141058] Bridge firewalling registered [ 2.153891] 8021q: 802.1Q VLAN Support v1.8 [ 2.157865] Registering SWP/SWPB emulation handler [ 2.173547] ubi0: attaching mtd8 [ 9.098960] ubi0: scanning is finished [ 9.174691] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 10, need 19 [ 9.176218] ubi0: attached mtd8 (name "rootfs", size 128 MiB) [ 9.183933] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 9.189874] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 9.196626] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 9.203465] ubi0: good PEBs: 1023, bad PEBs: 1, corrupted PEBs: 0 [ 9.210252] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 9.216504] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1392447968 [ 9.223608] ubi0: available PEBs: 0, total reserved PEBs: 1023, PEBs reserved for bad PEB handling: 10 [ 9.232938] ubi0: background thread "ubi_bgt0d" started, PID 97 [ 9.236344] hctosys: unable to open rtc device (rtc0) [ 9.240466] clk: Not disabling unused clocks [ 9.240481] ALSA device list: [ 9.240484] No soundcards found. [ 9.279048] VFS: Mounted root (squashfs filesystem) readonly on device 31:10. [ 9.281754] Freeing unused kernel memory: 1024K (c0a00000 - c0b00000) [ 11.256956] init: Console is alive [ 11.257181] init: - watchdog - [ 17.367449] usbcore: registered new interface driver usbfs [ 17.367567] usbcore: registered new interface driver hub [ 17.371981] usbcore: registered new device driver usb [ 17.380387] Button Hotplug driver version 0.4.1 [ 17.387805] exFAT: Version 1.2.9 [ 17.388959] hw_wdt enter probe [ 17.401670] SCSI subsystem initialized [ 17.423418] libata version 3.00 loaded. [ 17.432099] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 17.433125] ehci-platform: EHCI generic platform driver [ 17.444209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 17.445354] ohci-platform: OHCI generic platform driver [ 17.451510] uhci_hcd: USB Universal Host Controller Interface driver [ 17.977613] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 17.977678] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 17.982245] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x00010010 [ 17.989678] xhci-hcd xhci-hcd.0.auto: irq 193, io mem 0x08a00000 [ 17.999238] hub 1-0:1.0: USB hub found [ 18.004523] hub 1-0:1.0: 1 port detected [ 18.008595] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 18.012136] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 18.017616] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 18.025898] hub 2-0:1.0: USB hub found [ 18.033333] hub 2-0:1.0: 1 port detected [ 18.037507] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 18.040964] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 18.046539] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x00010010 [ 18.053856] xhci-hcd xhci-hcd.1.auto: irq 194, io mem 0x06000000 [ 18.063440] hub 3-0:1.0: USB hub found [ 18.068791] hub 3-0:1.0: 1 port detected [ 18.072757] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 18.076407] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 18.081748] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 18.090139] hub 4-0:1.0: USB hub found [ 18.097603] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 18.102700] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio-leds/power[0]' - status (0) [ 18.102892] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio-leds/lte[0]' - status (0) [ 18.104683] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio_keys/button@1[0]' - status (0) [ 18.104753] gpio-63 (reset): gpiod_set_debounce: missing set() or set_debounce() operations [ 18.105378] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0 [ 18.111500] usbcore: registered new interface driver usb-storage [ 18.117773] usbcore: registered new interface driver uas [ 18.260480] init: - preinit - [ 18.325288] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 18.385198] usb 3-1: new full-speed USB device number 2 using xhci-hcd [ 21.150790] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 138 [ 21.566028] UBIFS (ubi0:2): recovery needed [ 22.587423] UBIFS (ubi0:2): recovery completed [ 22.589067] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 22.590865] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 22.598772] UBIFS (ubi0:2): FS size: 95739904 bytes (91 MiB, 754 LEBs), journal size 4825088 bytes (4 MiB, 38 LEBs) [ 22.608670] UBIFS (ubi0:2): reserved for root: 4522032 bytes (4416 KiB) [ 22.618900] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 41A33E79-7F57-40F7-8A89-9B86EADE8BAB, small LPT model [ 22.680490] mount_root: switching to jffs2 overlay [ 22.891708] procd: - early - [ 22.891812] procd: - watchdog - [ 23.819371] procd: - ubus - [ 24.824083] procd: - init - [ 27.101764] nf_conntrack version 0.5.0 (3681 buckets, 14724 max) [ 27.133977] cfg80211: World regulatory domain updated: [ 27.134011] cfg80211: DFS Master region: unset [ 27.138097] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 27.142631] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 27.152310] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 27.154397] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 27.163696] PPP generic driver version 2.4.2 [ 27.174570] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 27.178854] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 27.186577] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 27.196292] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 27.205748] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 27.213799] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 29.954320] ssdk_switch_device_num_init[998]:INFO:ess-switch dts node number: 1 [ 29.958110] ssdk_dt_get_switch_node[836]:INFO:ess-switch DT exist! [ 29.964949] ssdk_dt_parse_access_mode[737]:INFO:switch_access_mode: local bus [ 29.971107] ssdk_dt_parse_access_mode[750]:INFO:switchreg_base_addr: 0xc000000 [ 29.978237] ssdk_dt_parse_access_mode[751]:INFO:switchreg_size: 0x80000 [ 29.985442] ssdk_dt_parse_mac_mode[242]:INFO:mac mode = 0x0 [ 29.991677] ssdk_dt_parse_mac_mode[248]:INFO:mac mode1 doesn't exit! [ 29.997248] ssdk_dt_parse_mac_mode[257]:INFO:mac mode2 doesn't exit! [ 30.003571] ssdk_dt_parse_phy_info[515]:INFO:qcom,port_phyinfo DT doesn't exist! [ 30.009919] ssdk_dt_parse_mdio[605]:INFO:mdio DT exist! [ 30.016967] ssdk_dt_parse_led[810]:INFO:current dts led_source_num is 0 [ 30.022154] ssdk_dt_parse_psgmii[702]:INFO:ess-psgmii DT exist! [ 30.029107] ssdk_plat_init start [ 30.031171] ssdk_plat_init[1282]:INFO:Enable ess clk [ 30.099363] malibu_phy_api_ops_init[2849]:INFO:qca probe malibu phy driver succeeded! [ 30.106214] regi_init[3369]:INFO:Initializing DESS!! [ 31.795295] ssdk_switch_register[1617]:INFO:Chip version 0x1401 [ 31.798300] qca_link_polling_select[1279]:INFO:link-polling-required node does not exist [ 31.804529] ssdk_switch_register[1642]:INFO:polling is selected [ 31.812255] regi_init[3378]:INFO:Initializing DESS Done!! [ 31.817214] regi_init[3407]:INFO:qca-ssdk module init succeeded! [ 31.854501] tun: Universal TUN/TAP device driver, 1.6 [ 31.854534] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 31.864284] l2tp_core: L2TP core driver, V2.0 [ 31.865756] l2tp_netlink: L2TP netlink interface [ 31.871624] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded. [ 31.874809] gre: GRE over IPv4 demultiplexor driver [ 31.882868] ip_gre: GRE over IPv4 tunneling driver [ 31.903014] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 31.913785] QCA multicast snooping installed successfully [ 31.918013] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 33.196652] Netfilter messages via NETLINK v0.30. [ 33.199473] ip_set: protocol 6 [ 33.415335] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 33.415384] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 33.420796] usb usb2-port1: cannot disable (err = -32) [ 36.485341] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 36.485390] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 36.490787] usb usb2-port1: cannot disable (err = -32) [ 36.651802] QCA Hy-Fi multicast installation successfully [ 38.896441] u32 classifier [ 38.896468] input device check on [ 38.898040] Actions configured [ 39.366349] Mirror/redirect action on [ 39.555301] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 39.555352] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 39.560753] usb usb2-port1: cannot disable (err = -32) [ 42.625359] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 42.625411] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 42.630809] usb usb2-port1: cannot disable (err = -32) [ 43.762902] fuse init (API version 7.23) [ 43.954567] usbcore: registered new interface driver cdc_acm [ 43.954599] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 43.961577] usbcore: registered new interface driver cdc_wdm [ 43.978884] Ebtables v2.0 registered [ 43.979885] Custom GPIO-based I2C driver version 0.1.1 [ 43.982406] i2c-gpio i2c-gpio.0: using pins 59 (SDA) and 58 (SCL) [ 43.989112] ip_tables: (C) 2000-2006 Netfilter Core Team [ 43.994846] usbcore: registered new interface driver ipheth [ 44.076948] ctnetlink v0.93: registering with nfnetlink. [ 44.330254] PPP MPPE Compression module registered [ 44.331995] NET: Registered protocol family 24 [ 44.336542] PPTP driver version 0.8.5 [ 44.359879] usbcore: registered new interface driver usbserial [ 44.360092] usbcore: registered new interface driver usbserial_generic [ 44.364793] usbserial: USB Serial support registered for generic [ 44.384500] wireguard: WireGuard 1.0.20200611 loaded. See www.wireguard.com for information. [ 44.384540] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 44.432595] xt_time: kernel timezone is -0000 [ 44.436456] usbcore: registered new interface driver cdc_ether [ 44.440746] usbcore: registered new interface driver cdc_ncm [ 44.443093] usbcore: registered new interface driver cp210x [ 44.447732] usbserial: USB Serial support registered for cp210x [ 44.452935] cp210x 3-1:1.0: cp210x converter detected [ 44.459100] usb 3-1: cp210x converter now attached to ttyUSB0 [ 44.469333] usbcore: registered new interface driver huawei_cdc_ncm [ 44.476580] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 44.515632] qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device [ 44.515671] qmi_wwan 1-1:1.4: QuectelEC25&EC21&EG91&EG95&EG06&EP06&EM06&BG96&AG35 work on RawIP mode [ 44.522555] qmi_wwan 1-1:1.4 wwan0: register 'qmi_wwan' at usb-xhci-hcd.0.auto-1, WWAN/QMI device, 92:b8:1c:db:75:20 [ 44.529428] usbcore: registered new interface driver qmi_wwan [ 44.542825] usbcore: registered new interface driver rndis_host [ 44.549001] usbcore: registered new interface driver sierra [ 44.551011] usbserial: USB Serial support registered for Sierra USB modem [ 44.558951] usbcore: registered new interface driver sierra_net [ 44.573480] usbcore: registered new interface driver option [ 44.573640] usbserial: USB Serial support registered for GSM modem (1-port) [ 44.578245] option 1-1:1.0: GSM modem (1-port) converter detected [ 44.585375] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 [ 44.591229] option 1-1:1.1: GSM modem (1-port) converter detected [ 44.598354] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 [ 44.604039] option 1-1:1.2: GSM modem (1-port) converter detected [ 44.611216] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3 [ 44.616953] option 1-1:1.3: GSM modem (1-port) converter detected [ 44.624093] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4 [ 45.695419] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 45.695473] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 45.700872] usb usb2-port1: cannot disable (err = -32) [ 48.775309] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 48.775361] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 48.780760] usb usb2-port1: cannot disable (err = -32) [ 50.050829] mem_manager: module license 'unspecified' taints kernel. [ 50.050866] Disabling lock debugging due to kernel taint [ 50.110383] qdf_dbg_mask value is invalid [ 50.110412] Using the default module debug levels instead [ 50.113379] qdf_print_ctrl_register: Allocated print control object 0 [ 50.118898] [ 50.118898] MINIDUMP VA .bss start=bf894080 module=qdf [ 51.845395] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 51.845456] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 51.851020] usb usb2-port1: cannot disable (err = -32) [ 54.915392] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 54.915448] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 54.920874] usb usb2-port1: cannot disable (err = -32) [ 56.706460] vmap allocation for size 2777088 failed: use vmalloc=<size> to increase size. [ 56.708537] vmap allocation for size 405504 failed: use vmalloc=<size> to increase size. [ 56.872173] wlan: [1571:E:CONFIG] cfg_uint_item_handler: 142: allow_mon_vaps_in_sr= - Invalid format (status 16); Using default 0 [ 56.872311] wlan: [1571:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50 [ 56.882969] [ 56.882969] MINIDUMP VA .bss start=d16d6500 module=umac [ 57.985350] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 57.985409] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 57.990977] usb usb2-port1: cannot disable (err = -32) [ 58.045313] vmap allocation for size 1204224 failed: use vmalloc=<size> to increase size. [ 58.046279] vmap allocation for size 212992 failed: use vmalloc=<size> to increase size. [ 58.120974] [ 58.120974] MINIDUMP VA .bss start=d1a78c00 module=qca_ol [ 58.325537] vmap allocation for size 614400 failed: use vmalloc=<size> to increase size. [ 58.337513] wlan: [1575:I:ANY] =======ol_if_register_wifi3_0========== [ 58.337513] [ 58.337577] wlan: [1575:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0: (Atheros/multi-bss) [ 58.344625] [ 58.344625] MINIDUMP VA .bss start=d10f89c0 module=wifi_3_0 [ 58.534457] vmap allocation for size 507904 failed: use vmalloc=<size> to increase size. [ 58.574259] wlan: [1576:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode [ 58.580104] wlan: [1576:I:ANY] qca_napi_create: 369: qca_napi_create: napi instance 32 created on pipe 4 [ 58.580996] wlan: [1576:I:ANY] __ol_ath_attach: 3524: Allocated soc cbe80500 [ 58.590428] wlan: [1576:I:ANY] btcoex_support 0 wlan_prio_gpio 0 [ 58.590428] [ 58.612269] wlan: [1576:I:ANY] __ol_ath_attach: 3750: dev name soc0 [ 58.612391] wlan: [1576:I:ANY] ol_target_init: 2453: 6ol_target_init() BMI inited. [ 58.617528] wlan: [1576:I:ANY] ol_target_init: 2467: 6ol_target_init() BMI Get Target Info. [ 58.624993] wlan: [1576:I:ANY] ol_target_init: 2474: Chip id: 0x10, chip version: 0x1000000 [ 58.633701] wlan: [1576:I:ANY] ol_ath_host_config_update: 5175: 6 [ 58.633701] CE WAR Disabled [ 58.633701] [ 58.641912] wlan: [1576:I:ANY] ol_ath_configure_target: 559: 6NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 58.652730] wlan: [1576:I:ANY] ol_target_init: 2496: 6ol_target_init() configure Target . [ 58.662433] wlan: [1576:I:ANY] ol_ath_download_firmware: 1929: [ 58.662433] Target Version is 1000000 [ 58.670423] wlan: [1576:I:ANY] ol_ath_download_firmware: 1939: [ 58.670423] Flash Download Address c0000 [ 58.680048] wlan: [1576:I:ANY] ol_transfer_bin_file: 1401: ol_transfer_bin_file: flash data file defined [ 58.690035] wlan: [1576:I:ANY] ol_transfer_bin_file: 1546: ol_transfer_bin_file[1546] Get Caldata for soc0. [ 58.699884] wlan: [1576:I:ANY] qc98xx_verify_checksum: 800: qc98xx_verify_checksum: flash checksum passed: 0x7b4a [ 58.709232] wlan: [1576:I:ANY] ol_transfer_bin_file: 1601: ol_transfer_bin_file 1601: Download Flash data len 12064 [ 58.719894] wlan: [1576:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 58.749427] wlan: [1576:I:ANY] ol_ath_download_firmware: 1947: [ 58.749427] Board data initialized [ 58.749610] wlan: [1576:I:ANY] ol_ath_download_firmware: 1962: 6ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 58.757676] wlan: [1576:I:ANY] ol_transfer_bin_file: 1007: 6 [ 58.757676] Selecting OTP binary for CHIP Version -807440028 [ 58.967288] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 58.983869] wlan: [1576:I:ANY] ol_ath_download_firmware: 1991: 6 [ 58.983869] First OTP send param 8000 [ 58.988582] wlan: [1576:I:ANY] ol_ath_download_firmware: 1997: ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 [ 58.992786] wlan: [1576:I:ANY] ol_ath_download_firmware: 2017: ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 [ 59.007227] wlan: [1576:I:ANY] ol_ath_download_firmware: 2085: 6ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 59.017301] wlan: [1576:I:ANY] boardid_to_filename: 426: [ 59.017301] soc0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin [ 59.028919] wlan: [1576:I:ANY] ol_transfer_bin_file: 1397: ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin [ 59.061571] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 3, Download data len 12064 [ 59.061877] wlan: [1576:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 59.091993] wlan: [1576:I:ANY] ol_ath_download_firmware: 2103: 6ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 59.092040] wlan: [1576:I:ANY] ol_transfer_bin_file: 1007: 6 [ 59.092040] Selecting OTP binary for CHIP Version -807440028 [ 59.102824] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 59.130770] wlan: [1576:I:ANY] ol_ath_download_firmware: 2119: [ 59.130770] [Flash] : Ignore Module param [ 59.130814] wlan: [1576:I:ANY] ol_ath_download_firmware: 2150: 6 [ 59.130814] Second otp download Param 10000 [ 59.149937] wlan: [1576:I:ANY] ol_ath_download_firmware: 2156: ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 59.150013] wlan: [1576:I:ANY] ol_transfer_bin_file: 1141: 6 [ 59.150013] Mission mode: Firmware CHIP Version -807440028 [ 59.433761] wlan: [1576:I:ANY] ol_swap_seg_alloc: 2846: 6ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 59.433761] [ 59.434339] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:206391 size_left:206411 dma_size_left:262144 fw_temp:d1881004 fw_entry_size:206415 [ 59.445905] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2943: ol_swap_wlan_memory_expansion: dma_virt_addr :d17aa000 fw_temp: d1881008 length: 206391 [ 59.462972] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2952: 6Swap: bytes_left to copy: fw:16; dma_page:55753 [ 59.462972] [ 59.476322] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:55753 fw_temp:d18b3643 fw_entry_size:206415 [ 59.488464] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2926: 6Swap: wrong length read:0 [ 59.488464] [ 59.504338] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2970: 6ol_swap_wlan_memory_expansion: Swap total_bytes copied: 206391 Target address 417d30 [ 59.504338] [ 59.514799] wlan: [1576:I:ANY] ol_transfer_swap_struct: 2742: 6soc=cbe80500 target_write_addr=417d30 seg_info=ce9956d0 [ 59.530031] wlan: [1576:I:ANY] ol_transfer_swap_struct: 2748: 6ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 59.540880] wlan: [1576:I:ANY] ol_ath_code_data_swap: 2854: 6bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 59.554349] wlan: [1576:I:ANY] ol_transfer_bin_file: 1209: ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 60.225403] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 1, Download data len 384756 [ 61.055315] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 61.055365] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 61.060823] usb usb2-port1: cannot disable (err = -32) [ 61.505509] wlan: [1576:I:ANY] ol_target_init: 2505: 6ol_target_init() Download FW done. [ 61.505564] wlan: [1576:I:ANY] ol_get_tgt_dump_location: 2308: Retrived fw_io_mem_size_l = 600000 fw_io_mem_addr_l = 87500000 [ 61.512697] wlan: [1576:I:ANY] ol_ath_copy_tgt_iram: 2378: tgt iram paddr: 0x980000 host paddr 0x87500000 Radio id 0 [ 61.689708] wlan: [1576:I:ANY] ol_ath_soc_attach: 7063: WMI attached. wmi_handle cbe56c00 [ 61.689761] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 145 is unavailable [ 61.696951] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 62 is unavailable [ 61.705494] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 152 is unavailable [ 61.714061] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 210 is unavailable [ 61.722589] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 208 is unavailable [ 61.731183] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 170 is unavailable [ 61.739824] wlan: [1576:I:ANY] htc_wmi_init: 6357: htc_wmi_init() HT Create . cbe78000 [ 61.748462] wlan: [1576:I:ANY] htc_wmi_init: 6421: [htc_wmi_init:6421] host_enable 0 nss_nwifi_offload 0 [ 61.762256] wlan: [1576:I:ANY] ol_target_init_complete: 6539: CDP soc attach success [ 61.766030] wlan: [1576:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle cbe78000, ep 2, value 1 [ 61.774686] wlan: [6:I:TIF] init_deinit_sw_version_check: 1734: Firmware_Build_Number:30 [ 61.783131] wlan: [6:E:TIF] init_deinit_populate_fw_version_cmd: 108: failed to save fw version [ 61.791395] wlan: [6:I:TIF] init_deinit_peer_cache_support: 255: Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 61.799850] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 2 idx 0 num_units 53 unit_len 256 [ 61.814063] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 3 idx 1 num_units 53 unit_len 1024 [ 61.823727] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 4 idx 2 num_units 53 unit_len 4096 [ 61.833661] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 8 idx 3 num_units 1 unit_len 327680 [ 61.844073] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 9 idx 4 num_units 1 unit_len 819200 [ 61.853553] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 1 idx 5 num_units 531 unit_len 744 [ 61.863252] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 6 idx 6 num_units 35 unit_len 3072 [ 61.873052] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 7 idx 7 num_units 1 unit_len 6144 [ 61.883789] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 5 idx 8 num_units 531 unit_len 2084 [ 61.892714] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 361: Do not allocate DFS object for 2G, pdev_id = 0 [ 61.902581] wlan: [6:I:ANY] ol_tx_pflow_ctrl_init: 259: Startup Mode-0 set [ 61.915453] wlan: [6:I:ANY] htt_alloc_peer_map_mem: 141: [ 61.915453] htt_alloc_peer_map_mem : Alloc Success : host q vaddr cbc44000 paddr 8bc44000 [ 61.921895] wlan: [6:I:ANY] htt_alloc_peer_map_mem: 142: [ 61.921895] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 61.938722] wlan: [6:I:ANY] 6 [ 61.938722] <=== cfg max peer id 2080 ====> [ 61.938722] [ 61.948483] wlan: [6:I:ANY] ol_txrx_pdev_attach: 1039: 62500 tx desc's allocated ; range starts from caf00000 [ 61.957504] wlan: [6:I:TIF] init_deinit_update_pdev_tgt_info: 1082: CDP PDEV ATTACH success [ 62.109598] wlan: [6:E:TIF] init_deinit_ready_event_handler: 464: agile capability disabled in HW [ 62.109679] wlan: [1576:I:ANY] __ol_ath_check_wmi_ready: 5032: ABI Version mismatch: Host(0x3), Target(0x0) [ 62.117503] wlan: [1576:I:ANY] ol_ath_connect_htc: 1235: WMI is ready [ 62.127061] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 104 is unavailable [ 62.133645] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 163 is unavailable [ 62.142153] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 181 is unavailable [ 62.150734] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 168 is unavailable [ 62.159322] wlan: [1576:E:CMN_MLME] target_if_vdev_mgr_wmi_event_register: 688: failed to register for delete response [ 62.167919] wlan: [1576:E:DIRECT_BUF_RX] direct_buf_rx_target_attach: 146: hal soc or osdev is null [ 62.178596] wlan: [1576:I:ANY] ol_ath_soc_attach: 7143: ol_ath_soc_attach: Direct Buffer Rx Target Attach Failed [ 62.187537] wlan: [1576:I:ANY] ol_ath_soc_attach: 7150: connect HTC [ 62.197946] wlan: [1576:I:ANY] ol_ath_soc_attach: 7151: bypasswmi : 0 [ 62.203920] wlan: [1576:E:WMI] event handler already registered 0x9017 [ 62.210533] wlan: [1576:E:WMI] event handler already registered 0x9018 [ 62.216952] wlan: [1576:E:WMI] event handler already registered 0x9019 [ 62.223453] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 105 is unavailable [ 62.229995] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 188 is unavailable [ 62.238572] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 189 is unavailable [ 62.247173] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 142 is unavailable [ 62.255775] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 149 is unavailable [ 62.264349] wlan: [1576:I:ANY] ol_ath_soc_attach: 7231: ol_ath_soc_attach() UMAC attach . [ 62.273051] wlan: [1576:I:ANY] __ol_ath_attach: 3866: pdev_netdev name wifi0 [ 62.281274] wlan: [1576:I:ANY] htt_h2t_frag_desc_bank_cfg_msg: 217: HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for SoC ID = 0 [ 62.281293] wlan: [0:I:ANY] htt_t2h_msg_handler_misc: 449: 6target uses HTT version 2.2; host uses 2.2 [ 62.306265] wlan: [1576:I:ANY] __ol_ath_attach: 3937: BURSTING enabled by default [ 62.309228] wlan: [1576:I:ANY] ol_ath_pdev_attach: 8528: interface_id 0 [ 62.316884] wlan: [1576:I:ANY] ol_ath_update_fw_adfs_support: 286: ol_ath_update_fw_adfs_support: Returning due to null table [ 62.323216] wlan: [1576:I:ANY] ol_regdmn_start: 425: ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 62.335233] wlan: [1576:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 62.349927] ol_ath_pdev_ctl_failsafe_check_event_handler: CTL FAILSAFE Algorithm invoked when computing CTL table [ 62.349928] wlan: [1576:I:ANY] ieee80211_cbs_init [ 62.366777] wlan: [1576:I:ANY] CBS Inited [ 62.366777] [ 62.371500] wlan: [1576:I:ANY] acfg_attach: 3473: acfg_attach: 3473: Netlink socket created:cddae000 [ 62.376966] wlan: [1576:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX [ 62.386238] wlan: [1576:I:ANY] ol_ath_stats_attach: 2134: periodic_chan_stats: 1 [ 62.396509] wlan: [1576:I:ANY] ol_txrx_mgmt_tx_cb_set: 3436: >>>> CB Set 00000000 [ 62.404028] wlan: [1576:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11 [ 62.411204] of_get_named_gpiod_flags: can't parse 'wifi-led-gpios' property of node '/soc/wifi@a000000[0]' [ 62.411223] wlan: [1576:I:ANY] ipq4019_wifi_led_init: Wifi LED init failed.. Couldn't get led gpio/led source [ 62.411223] [ 62.418623] wlan: [0:I:ANY] ol_ath_pdev_attach: 8890: Set global_ic[1], ptr:d16d682c [ 62.429815] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(cce2a104) is_primary 1 [ 62.437798] wlan: [1576:I:ANY] ol_ath_pdev_attach: 9019: Pdev = 0 Number of peers = 530 [ 62.447757] wlan: [1576:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 2099: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5 [ 62.447757] [ 62.453865] wlan: [1576:E:ANY] ol_ath_set_obss_thresh: 7905: ol_ath_set_obss_thresh: Could not set obss pd thresh enable val [ 62.471225] wlan: [1576:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 560: cfg block channel list is empty [ 62.482517] wlan: [1576:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3455: pdev_idx = 0 tx_desc_limit = 0 [ 62.492068] wlan: [1576:I:ANY] smart_log_init: 1616: Smart logging Enabled buf=ca990000 (size=65536) [ 62.501532] wlan: [1576:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 62.501532] [ 62.510715] wlan: [1576:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 62.510715] [ 62.518787] wlan: [1576:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =cb74e400 ic->ic_wrap_com=cb74e400 &wrap_com->wc_devt=cb74e400 [ 62.518787] [ 62.528027] wlan: [1576:I:ANY] __ol_ath_attach: 4072: __ol_ath_attach[4072] WAPI MBSSID 2 [ 62.542265] wlan: [1576:I:ANY] __ol_ath_attach: 4118: needed_headroom reservation 60 [ 62.550585] wlan: [1576:I:ANY] wlan_cfg80211_init: 10903: Number of 2G channels: 11 [ 62.558981] wlan: [1576:I:ANY] ieee80211_cfg80211_radio_attach: 11009: ic: 0xcb380500, wdev: 0xcb38fc90, wiphy: 0xcddae960, netdev: 0xcb380000 [ 62.568461] wlan: [1576:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3424: Running with HW mode = 7 [ 62.580048] wlan: [1576:E:QLD] qld_register: 108: Handle or address is NULL [ 62.589354] wlan: [1576:I:ANY] wlan_pdev_operation: 744: num_radios=1, wifi_radios[0].sc = cb380500_radio_type = 2 [ 62.616331] wlan: [1576:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode [ 62.622271] wlan: [1576:I:ANY] qca_napi_create: 369: qca_napi_create: napi instance 32 created on pipe 4 [ 62.623156] wlan: [1576:I:ANY] __ol_ath_attach: 3524: Allocated soc caa40500 [ 62.632564] wlan: [1576:I:ANY] btcoex_support 0 wlan_prio_gpio 0 [ 62.632564] [ 62.639724] wlan: [1576:I:ANY] __ol_ath_attach: 3750: dev name soc1 [ 62.646884] wlan: [1576:I:ANY] ol_target_init: 2453: 6ol_target_init() BMI inited. [ 62.652953] wlan: [1576:I:ANY] ol_target_init: 2467: 6ol_target_init() BMI Get Target Info. [ 62.660530] wlan: [1576:I:ANY] ol_target_init: 2474: Chip id: 0x10, chip version: 0x1000000 [ 62.669230] wlan: [1576:I:ANY] ol_ath_host_config_update: 5175: 6 [ 62.669230] CE WAR Disabled [ 62.669230] [ 62.677471] wlan: [1576:I:ANY] ol_ath_configure_target: 559: 6NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 62.688318] wlan: [1576:I:ANY] ol_target_init: 2496: 6ol_target_init() configure Target . [ 62.698029] wlan: [1576:I:ANY] ol_ath_download_firmware: 1929: [ 62.698029] Target Version is 1000000 [ 62.705956] wlan: [1576:I:ANY] ol_ath_download_firmware: 1939: [ 62.705956] Flash Download Address c0000 [ 62.716164] wlan: [1576:I:ANY] ol_transfer_bin_file: 1401: ol_transfer_bin_file: flash data file defined [ 62.725569] wlan: [1576:I:ANY] ol_transfer_bin_file: 1546: ol_transfer_bin_file[1546] Get Caldata for soc1. [ 62.735473] wlan: [1576:I:ANY] qc98xx_verify_checksum: 800: qc98xx_verify_checksum: flash checksum passed: 0x3872 [ 62.744722] wlan: [1576:I:ANY] ol_transfer_bin_file: 1601: ol_transfer_bin_file 1601: Download Flash data len 12064 [ 62.755485] wlan: [1576:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 62.765498] wlan: [6:E:ANY] [soc0] FWLOG: [73742] WAL_DBGID_RST_STATS ( 0x1, 0x1, 0x96c, 0x0, 0x416064) [ 62.765498] [ 62.774770] wlan: [6:E:ANY] [soc0] FWLOG: [73782] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0) [ 62.774770] [ 62.785865] wlan: [6:E:ANY] [soc0] FWLOG: [73782] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0) [ 62.785865] [ 62.797033] wlan: [6:E:ANY] [soc0] FWLOG: [73782] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0) [ 62.797033] [ 62.808334] wlan: [6:E:ANY] [soc0] FWLOG: [73782] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0) [ 62.808334] [ 62.819768] wlan: [6:E:ANY] [soc0] FWLOG: [74017] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x0, 0x7, 0x10, 0x10) [ 62.819768] [ 62.831265] wlan: [6:E:ANY] [soc0] FWLOG: [74017] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x10, 0x10, 0x10, 0x12) [ 62.831265] [ 62.857726] wlan: [1576:I:ANY] ol_ath_download_firmware: 1947: [ 62.857726] Board data initialized [ 62.857903] wlan: [1576:I:ANY] ol_ath_download_firmware: 1962: 6ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 62.865989] wlan: [1576:I:ANY] ol_transfer_bin_file: 1007: 6 [ 62.865989] Selecting OTP binary for CHIP Version -807439236 [ 62.878307] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 62.906447] wlan: [1576:I:ANY] ol_ath_download_firmware: 1991: 6 [ 62.906447] First OTP send param 8000 [ 62.911155] wlan: [1576:I:ANY] ol_ath_download_firmware: 1997: ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 [ 62.915395] wlan: [1576:I:ANY] ol_ath_download_firmware: 2017: ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 [ 62.929802] wlan: [1576:I:ANY] ol_ath_download_firmware: 2085: 6ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 62.939883] wlan: [1576:I:ANY] boardid_to_filename: 426: [ 62.939883] soc1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin [ 62.951509] wlan: [1576:I:ANY] ol_transfer_bin_file: 1397: ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin [ 62.977710] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 3, Download data len 12064 [ 62.980819] wlan: [1576:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 63.011980] wlan: [1576:I:ANY] ol_ath_download_firmware: 2103: 6ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 63.012026] wlan: [1576:I:ANY] ol_transfer_bin_file: 1007: 6 [ 63.012026] Selecting OTP binary for CHIP Version -807439236 [ 63.022800] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 63.050757] wlan: [1576:I:ANY] ol_ath_download_firmware: 2119: [ 63.050757] [Flash] : Ignore Module param [ 63.050800] wlan: [1576:I:ANY] ol_ath_download_firmware: 2150: 6 [ 63.050800] Second otp download Param 10000 [ 63.070203] wlan: [1576:I:ANY] ol_ath_download_firmware: 2156: ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 63.070251] wlan: [1576:I:ANY] ol_transfer_bin_file: 1141: 6 [ 63.070251] Mission mode: Firmware CHIP Version -807439236 [ 63.083681] wlan: [1576:I:ANY] ol_swap_seg_alloc: 2846: 6ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 [ 63.083681] [ 63.094680] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:206391 size_left:206411 dma_size_left:262144 fw_temp:d2440004 fw_entry_size:206415 [ 63.107221] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2943: ol_swap_wlan_memory_expansion: dma_virt_addr :d2681000 fw_temp: d2440008 length: 206391 [ 63.124334] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2952: 6Swap: bytes_left to copy: fw:16; dma_page:55753 [ 63.124334] [ 63.137678] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:55753 fw_temp:d2472643 fw_entry_size:206415 [ 63.149812] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2926: 6Swap: wrong length read:0 [ 63.149812] [ 63.165687] wlan: [1576:I:ANY] ol_swap_wlan_memory_expansion: 2970: 6ol_swap_wlan_memory_expansion: Swap total_bytes copied: 206391 Target address 417d30 [ 63.165687] [ 63.176141] wlan: [1576:I:ANY] ol_transfer_swap_struct: 2742: 6soc=caa40500 target_write_addr=417d30 seg_info=ca9fc3d0 [ 63.191381] wlan: [1576:I:ANY] ol_transfer_swap_struct: 2748: 6ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 63.202231] wlan: [1576:I:ANY] ol_ath_code_data_swap: 2854: 6bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 63.215638] wlan: [1576:I:ANY] ol_transfer_bin_file: 1209: ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 63.230845] wlan: [1576:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 1, Download data len 384756 [ 64.125333] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 64.125387] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 64.130845] usb usb2-port1: cannot disable (err = -32) [ 64.522077] wlan: [1576:I:ANY] ol_target_init: 2505: 6ol_target_init() Download FW done. [ 64.522134] wlan: [1576:I:ANY] ol_get_tgt_dump_location: 2308: Retrived fw_io_mem_size_l = 600000 fw_io_mem_addr_l = 87500000 [ 64.529310] wlan: [1576:I:ANY] ol_ath_copy_tgt_iram: 2378: tgt iram paddr: 0x980000 host paddr 0x87700000 Radio id 1 [ 64.706492] wlan: [1576:I:ANY] ol_ath_soc_attach: 7063: WMI attached. wmi_handle cb74fc00 [ 64.706544] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 145 is unavailable [ 64.713676] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 62 is unavailable [ 64.722284] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 152 is unavailable [ 64.730868] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 210 is unavailable [ 64.739370] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 208 is unavailable [ 64.747971] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 170 is unavailable [ 64.756614] wlan: [1576:I:ANY] htc_wmi_init: 6357: htc_wmi_init() HT Create . ca9a7000 [ 64.765240] wlan: [1576:I:ANY] htc_wmi_init: 6421: [htc_wmi_init:6421] host_enable 0 nss_nwifi_offload 0 [ 64.779107] wlan: [1576:I:ANY] ol_target_init_complete: 6539: CDP soc attach success [ 64.782779] wlan: [1576:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ca9a7000, ep 2, value 1 [ 64.791548] wlan: [6:I:TIF] init_deinit_sw_version_check: 1734: Firmware_Build_Number:30 [ 64.799921] wlan: [6:E:TIF] init_deinit_populate_fw_version_cmd: 108: failed to save fw version [ 64.808187] wlan: [6:I:TIF] init_deinit_peer_cache_support: 255: Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 64.816625] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 2 idx 0 num_units 53 unit_len 256 [ 64.830897] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 3 idx 1 num_units 53 unit_len 1024 [ 64.840533] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 4 idx 2 num_units 53 unit_len 4096 [ 64.850410] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 8 idx 3 num_units 1 unit_len 327680 [ 64.860808] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 9 idx 4 num_units 1 unit_len 819200 [ 64.870335] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 1 idx 5 num_units 531 unit_len 744 [ 64.880078] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 6 idx 6 num_units 35 unit_len 3072 [ 64.889838] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 7 idx 7 num_units 1 unit_len 6144 [ 64.900571] wlan: [6:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 5 idx 8 num_units 531 unit_len 2084 [ 64.909565] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 389: dfs_offload 0 [ 64.919181] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1579: dfs->dfs_psoc_idx: 0 [ 64.929051] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1585: dfs_soc_obj->num_dfs_privs: 1 [ 64.939127] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_get_po_radars: 400: UNINIT domain [ 64.948901] wlan: [6:I:ANY] ol_tx_pflow_ctrl_init: 259: Startup Mode-0 set [ 64.957164] wlan: [6:I:ANY] htt_alloc_peer_map_mem: 141: [ 64.957164] htt_alloc_peer_map_mem : Alloc Success : host q vaddr ca03a000 paddr 8a03a000 [ 64.963508] wlan: [6:I:ANY] htt_alloc_peer_map_mem: 142: [ 64.963508] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 64.980398] wlan: [6:I:ANY] 6 [ 64.980398] <=== cfg max peer id 2080 ====> [ 64.980398] [ 64.990144] wlan: [6:I:ANY] ol_txrx_pdev_attach: 1039: 62500 tx desc's allocated ; range starts from c9860000 [ 64.999144] wlan: [6:I:TIF] init_deinit_update_pdev_tgt_info: 1082: CDP PDEV ATTACH success [ 65.150942] wlan: [6:E:TIF] init_deinit_ready_event_handler: 464: agile capability disabled in HW [ 65.151022] wlan: [1576:I:ANY] __ol_ath_check_wmi_ready: 5032: ABI Version mismatch: Host(0x3), Target(0x0) [ 65.158846] wlan: [1576:I:ANY] ol_ath_connect_htc: 1235: WMI is ready [ 65.168382] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 104 is unavailable [ 65.174989] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 163 is unavailable [ 65.183499] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 181 is unavailable [ 65.192076] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 168 is unavailable [ 65.200669] wlan: [1576:E:CMN_MLME] target_if_vdev_mgr_wmi_event_register: 688: failed to register for delete response [ 65.209264] wlan: [1576:E:DIRECT_BUF_RX] direct_buf_rx_target_attach: 146: hal soc or osdev is null [ 65.219942] wlan: [1576:I:ANY] ol_ath_soc_attach: 7143: ol_ath_soc_attach: Direct Buffer Rx Target Attach Failed [ 65.228879] wlan: [1576:I:ANY] ol_ath_soc_attach: 7150: connect HTC [ 65.239292] wlan: [1576:I:ANY] ol_ath_soc_attach: 7151: bypasswmi : 0 [ 65.245282] wlan: [1576:E:WMI] event handler already registered 0x9017 [ 65.251859] wlan: [1576:E:WMI] event handler already registered 0x9018 [ 65.258300] wlan: [1576:E:WMI] event handler already registered 0x9019 [ 65.264799] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 105 is unavailable [ 65.271335] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 188 is unavailable [ 65.279923] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 189 is unavailable [ 65.288517] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 142 is unavailable [ 65.297117] wlan: [1576:E:WMI] wmi_unified_register_event_handler: Event id 149 is unavailable [ 65.305706] wlan: [1576:I:ANY] ol_ath_soc_attach: 7231: ol_ath_soc_attach() UMAC attach . [ 65.314326] wlan: [1576:I:ANY] __ol_ath_attach: 3866: pdev_netdev name wifi1 [ 65.322621] wlan: [1576:I:ANY] htt_h2t_frag_desc_bank_cfg_msg: 217: HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for SoC ID = 1 [ 65.322638] wlan: [0:I:ANY] htt_t2h_msg_handler_misc: 449: 6target uses HTT version 2.2; host uses 2.2 [ 65.347598] wlan: [1576:I:ANY] __ol_ath_attach: 3937: BURSTING enabled by default [ 65.350578] wlan: [1576:I:ANY] ol_ath_pdev_attach: 8528: interface_id 1 [ 65.358231] wlan: [1576:I:ANY] ol_ath_update_fw_adfs_support: 286: ol_ath_update_fw_adfs_support: Returning due to null table [ 65.364559] wlan: [1576:I:ANY] ol_regdmn_start: 425: ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 65.379589] wlan: [1576:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 65.391277] wlan: [1576:I:ANY] ieee80211_cbs_init [ 65.397716] wlan: [1576:I:ANY] CBS Inited [ 65.397716] [ 65.402574] wlan: [1576:I:ANY] acfg_attach: 3423: acfg_attach: Offload using existing sock cddae000 [ 65.408050] wlan: [1576:I:ANY] acfg_attach: Offload using existing sock cddae000 [ 65.408050] [ 65.417000] wlan: [1576:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX [ 65.426023] wlan: [1576:I:ANY] ol_ath_stats_attach: 2134: periodic_chan_stats: 1 [ 65.436385] wlan: [1576:I:ANY] ol_txrx_mgmt_tx_cb_set: 3436: >>>> CB Set 00000000 [ 65.444391] wlan: [1576:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 25 [ 65.451079] of_get_named_gpiod_flags: can't parse 'wifi-led-gpios' property of node '/soc/wifi@a800000[0]' [ 65.451099] wlan: [1576:I:ANY] ipq4019_wifi_led_init: Wifi LED init failed.. Couldn't get led gpio/led source [ 65.451099] [ 65.458494] wlan: [0:I:ANY] ol_ath_pdev_attach: 8890: Set global_ic[2], ptr:d16d682c [ 65.469681] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ca984704) is_primary 0 [ 65.477674] wlan: [1576:I:ANY] ol_ath_pdev_attach: 9019: Pdev = 0 Number of peers = 530 [ 65.487629] wlan: [1576:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 2099: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5 [ 65.487629] [ 65.493733] wlan: [1576:E:ANY] ol_ath_set_obss_thresh: 7905: ol_ath_set_obss_thresh: Could not set obss pd thresh enable val [ 65.511107] wlan: [1576:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 560: cfg block channel list is empty [ 65.522383] wlan: [1576:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3455: pdev_idx = 0 tx_desc_limit = 0 [ 65.531945] wlan: [1576:I:ANY] smart_log_init: 1616: Smart logging Enabled buf=c9b30000 (size=65536) [ 65.541399] wlan: [1576:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 65.541399] [ 65.550577] wlan: [1576:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 65.550577] [ 65.558661] wlan: [1576:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ccb2d400 ic->ic_wrap_com=ccb2d400 &wrap_com->wc_devt=ccb2d400 [ 65.558661] [ 65.567895] wlan: [1576:I:ANY] __ol_ath_attach: 4072: __ol_ath_attach[4072] WAPI MBSSID 2 [ 65.582133] wlan: [1576:I:ANY] __ol_ath_attach: 4118: needed_headroom reservation 60 [ 65.590478] wlan: [1576:I:ANY] wlan_cfg80211_init: 10915: Number of 5G channels: 25 [ 65.598919] wlan: [1576:I:ANY] ieee80211_cfg80211_radio_attach: 11009: ic: 0xca380500, wdev: 0xca38fc90, wiphy: 0xca9afd60, netdev: 0xca380000 [ 65.608417] wlan: [1576:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3424: Running with HW mode = 7 [ 65.620216] wlan: [1576:E:QLD] qld_register: 108: Handle or address is NULL [ 65.629220] wlan: [1576:I:ANY] wlan_pdev_operation: 744: num_radios=2, wifi_radios[1].sc = ca380500_radio_type = 2 [ 65.636129] wlan: [1576:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss) [ 65.656489] wlan: [1629:I:ANY] pktlog_init_2_0: 1556: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 65.656579] wlan: [1629:I:ANY] pktlog_init_2_0: 1556: Initializing Pktlog for AR900B, pktlog_hdr_size = 16 [ 65.774335] wlan: [6:E:ANY] [soc1] FWLOG: [76858] WAL_DBGID_RST_STATS ( 0x1, 0x1, 0x1464, 0x0, 0x416064) [ 65.774335] [ 65.774400] wlan: [6:E:ANY] [soc1] FWLOG: [76898] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0) [ 65.774400] [ 65.785289] wlan: [6:E:ANY] [soc1] FWLOG: [76898] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0) [ 65.785289] [ 65.795718] wlan: [6:E:ANY] [soc1] FWLOG: [76898] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0) [ 65.795718] [ 65.806987] wlan: [6:E:ANY] [soc1] FWLOG: [76898] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0) [ 65.806987] [ 65.818460] wlan: [6:E:ANY] [soc1] FWLOG: [77136] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x0, 0x7, 0x10, 0x10) [ 65.818460] [ 65.829717] wlan: [6:E:ANY] [soc1] FWLOG: [77136] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x10, 0x10, 0x10, 0x12) [ 65.829717] [ 67.196413] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 67.196487] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 67.201917] usb usb2-port1: cannot disable (err = -32) [ 70.305390] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 70.305448] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 70.310858] usb usb2-port1: cannot disable (err = -32) [ 73.546093] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 73.546159] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 73.551574] usb usb2-port1: cannot disable (err = -32) [ 74.897314] vmap allocation for size 610304 failed: use vmalloc=<size> to increase size. [ 74.953712] ECM init [ 74.953804] ECM database jhash random seed: 0x30620735 [ 74.956825] ECM init complete [ 76.031111] rtc-sd2068 0-0032: rtc core: registered sd2068 as rtc0 [ 76.039167] i2c i2c-0: new_device: Instantiated device sd2068 at 0x32 [ 76.646602] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 76.646680] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 76.652132] usb usb2-port1: cannot disable (err = -32) [ 76.766971] IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready [ 76.770388] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 76.778196] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 76.793804] device eth1 entered promiscuous mode [ 76.819056] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 76.910493] ess_edma c080000.edma: eth0: GMAC Link is up with phy_speed=1000 [ 76.910567] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 77.775245] br-lan: port 1(eth1) entered forwarding state [ 77.775356] br-lan: port 1(eth1) entered forwarding state [ 79.715773] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 79.715828] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 79.724823] usb usb2-port1: cannot disable (err = -32) [ 79.775213] br-lan: port 1(eth1) entered forwarding state [ 82.177342] wlan: [3638:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11 [ 82.177453] wlan: [3638:I:ANY] number of channels: 2G = 11 5G = 0 [ 82.184526] ol_ath_pdev_ctl_failsafe_check_event_handler: CTL FAILSAFE Algorithm invoked when computing CTL table [ 82.184528] wlan: [3638:I:ANY] wlan_cfg80211_set_country: 6081: wlan_cfg80211_set_country: Country: US ret: 0 [ 82.747735] wlan: [87:E:ANY] [soc0] FWLOG: [94347] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x0, 0x7, 0x10, 0x10) [ 82.747735] [ 82.747801] wlan: [87:E:ANY] [soc0] FWLOG: [94347] WAL_DBGID_PDEV_INFO_PRINT ( 0x16, 0x10, 0x10, 0x10, 0x12) [ 82.747801] [ 82.810091] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 82.810149] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 82.815601] usb usb2-port1: cannot disable (err = -32) [ 83.124984] wlan: [3808:I:ANY] wlan_cfg80211_set_hwaddr: 6154: wlan_cfg80211_set_hwaddr :94:83:c4:04:07:62 ret: 0 [ 83.218481] wlan: [3817:I:ANY] ol_ath_set_config_param: 1577: set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 83.553910] wlan: [0:I:ANY] ol_ath_set_config_param: 2328: Disconnect_timeout value: 10 [ 83.656575] wlan: [0:I:ANY] ol_ath_set_config_param: 2334: Reconfiguration_timeout value:60 [ 83.747249] wlan: [87:E:ANY] [soc0] FWLOG: [95324] WAL_DBGID_RST_STATS ( 0x2, 0x2, 0x96c, 0x0, 0x416064) [ 83.747249] [ 83.876576] wlan: [3926:I:ANY] osifp_create_wlan_vap: 10411: VDEV Create 94:83:c4:04:07:62 [ 83.876654] wlan: [3926:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 83.883753] wlan: [3926:I:ANY] wlan_vap_create: 1603: enter. devhandle=0xcb380500, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 83.883753] [ 83.892764] wlan: [3926:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 83.905057] wlan: [3926:I:ANY] MBO Initialized [ 83.911856] wlan: [3926:I:ANY] OCE Initialized [ 83.916355] wlan: [3926:I:ANY] wlan_vap_create: 1636: exit [ 83.920718] wlan: [3926:E:ANY] Smart Antenna is not supported [ 83.926429] wlan: [3926:E:ANY] Smart Antenna is not supported [ 83.932023] wlan: [3926:I:ANY] osif_create_vap_complete: 10609: TX Checksum:1|SG:1|TSO:1|LRO:1 [ 83.939741] wlan: [3926:I:ANY] VAP device tmp.wifi0 created osifp: (ccce9500) os_if: (c8098000) [ 83.946315] wlan: [3926:I:ANY] osif_ioctl_create_vap: 11056: 3VAP device tmp.wifi0 created! [ 83.956334] wlan: [3926:E:mlme] IF_STOP: V:0 Serialization queue disable [ 83.969101] wlan: [3926:I:ANY] ieee80211_node_latevdetach: vap still has nodes, vap->iv_node_count: 1, refcnt: 0xffffffff [ 83.969101] [ 83.970245] ieee80211_mbo_vdetach: MBO terminated [ 83.982535] ieee80211_oce_vdetach: OCE terminated [ 83.987502] wlan: [3926:I:ANY] ol_ath_soc_stop: 9653: Suspending Target soc=cbe80500 [ 83.991911] wlan: [3926:I:ANY] wlan_pdev_operation: 847: wlan_pdev_operation: disable_target_intr val is 1 [ 83.999865] wlan: [3926:I:ANY] ol_ath_soc_stop: 9656: ol_ath_soc_stop: waiting for target paused event from target [ 84.009338] wlan: [3926:I:ANY] ol_ath_soc_stop: 9682: disable dp interrupts:: soc: cbc01f80 [ 84.022973] wlan: [3926:I:ANY] 6ol_tx_me_exit: Already Disabled !!! [ 84.022973] [ 84.030276] wlan: [3926:E:WMI] send_thermal_mitigation_param_cmd_non_tlv:3014, htc_send_pkt failed, status:4 [ 84.036014] wlan: [3926:E:WMI] Failed to send WMI_TT_SET_CONF_CMDID [ 84.046107] wlan: [3926:E:WMI] Event id 104 is unavailable [ 84.051891] wlan: [3926:I:ANY] smart_log_deinit: 1747: smart_log_deinit: Smart logging Disabled [ 84.083124] wlan: [3926:I:ANY] ieee80211_cbs_init [ 84.083161] wlan: [3926:I:ANY] CBS Inited [ 84.083161] [ 84.087168] wlan: [3925:I:ANY] ol_ath_ucfg_setparam: 212: Starting the target before sending the command [ 84.112588] wlan: [3925:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode [ 84.116828] wlan: [3925:I:ANY] qca_napi_create: 369: qca_napi_create: napi instance 32 created on pipe 4 [ 84.119138] wlan: [3925:I:ANY] ol_target_init: 2453: 6ol_target_init() BMI inited. [ 84.129168] wlan: [3925:I:ANY] ol_target_init: 2467: 6ol_target_init() BMI Get Target Info. [ 84.136219] wlan: [3925:I:ANY] ol_target_init: 2474: Chip id: 0x10, chip version: 0x1000000 [ 84.144673] wlan: [3925:I:ANY] ol_ath_host_config_update: 5175: 6 [ 84.144673] CE WAR Disabled [ 84.144673] [ 84.153297] wlan: [3925:I:ANY] ol_ath_configure_target: 559: 6NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 84.163874] wlan: [3925:I:ANY] ol_target_init: 2496: 6ol_target_init() configure Target . [ 84.173695] wlan: [3925:I:ANY] ol_ath_download_firmware: 1929: [ 84.173695] Target Version is 1000000 [ 84.181629] wlan: [3925:I:ANY] ol_ath_download_firmware: 1939: [ 84.181629] Flash Download Address c0000 [ 84.191275] wlan: [3925:I:ANY] ol_transfer_bin_file: 1401: ol_transfer_bin_file: flash data file defined [ 84.201422] wlan: [3925:I:ANY] ol_transfer_bin_file: 1546: ol_transfer_bin_file[1546] Get Caldata for soc0. [ 84.210971] wlan: [3925:I:ANY] qc98xx_verify_checksum: 800: qc98xx_verify_checksum: flash checksum passed: 0x7b4a [ 84.220395] wlan: [3925:I:ANY] ol_transfer_bin_file: 1601: ol_transfer_bin_file 1601: Download Flash data len 12064 [ 84.230932] wlan: [3925:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 84.260437] wlan: [3925:I:ANY] ol_ath_download_firmware: 1947: [ 84.260437] Board data initialized [ 84.260619] wlan: [3925:I:ANY] ol_ath_download_firmware: 1962: 6ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 84.268701] wlan: [3925:I:ANY] ol_transfer_bin_file: 1007: 6 [ 84.268701] Selecting OTP binary for CHIP Version -807440028 [ 84.281016] wlan: [3925:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 84.309127] wlan: [3925:I:ANY] ol_ath_download_firmware: 1991: 6 [ 84.309127] First OTP send param 8000 [ 84.313836] wlan: [3925:I:ANY] ol_ath_download_firmware: 1997: ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 [ 84.318084] wlan: [3925:I:ANY] ol_ath_download_firmware: 2017: ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 [ 84.332472] wlan: [3925:I:ANY] ol_ath_download_firmware: 2085: 6ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 84.342551] wlan: [3925:I:ANY] boardid_to_filename: 426: [ 84.342551] soc0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin [ 84.354178] wlan: [3925:I:ANY] ol_transfer_bin_file: 1397: ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin [ 84.367244] wlan: [3925:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 3, Download data len 12064 [ 84.383515] wlan: [3925:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 84.414628] wlan: [3925:I:ANY] ol_ath_download_firmware: 2103: 6ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 84.414678] wlan: [3925:I:ANY] ol_transfer_bin_file: 1007: 6 [ 84.414678] Selecting OTP binary for CHIP Version -807440028 [ 84.425469] wlan: [3925:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 84.453413] wlan: [3925:I:ANY] ol_ath_download_firmware: 2119: [ 84.453413] [Flash] : Ignore Module param [ 84.453459] wlan: [3925:I:ANY] ol_ath_download_firmware: 2150: 6 [ 84.453459] Second otp download Param 10000 [ 84.472583] wlan: [3925:I:ANY] ol_ath_download_firmware: 2156: ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 84.472656] wlan: [3925:I:ANY] ol_transfer_bin_file: 1141: 6 [ 84.472656] Mission mode: Firmware CHIP Version -807440028 [ 84.486072] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:206391 size_left:206411 dma_size_left:262144 fw_temp:d240c004 fw_entry_size:206415 [ 84.496924] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2943: ol_swap_wlan_memory_expansion: dma_virt_addr :d17aa000 fw_temp: d240c008 length: 206391 [ 84.515272] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2952: 6Swap: bytes_left to copy: fw:16; dma_page:55753 [ 84.515272] [ 84.527855] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:55753 fw_temp:d243e643 fw_entry_size:206415 [ 84.539496] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2926: 6Swap: wrong length read:0 [ 84.539496] [ 84.555462] wlan: [3925:I:ANY] ol_swap_wlan_memory_expansion: 2970: 6ol_swap_wlan_memory_expansion: Swap total_bytes copied: 206391 Target address 417d30 [ 84.555462] [ 84.566545] wlan: [3925:I:ANY] ol_transfer_swap_struct: 2742: 6soc=cbe80500 target_write_addr=417d30 seg_info=ce9956d0 [ 84.581819] wlan: [3925:I:ANY] ol_transfer_swap_struct: 2748: 6ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 84.591903] wlan: [3925:I:ANY] ol_ath_code_data_swap: 2854: 6bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 84.605369] wlan: [3925:I:ANY] ol_transfer_bin_file: 1209: ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 84.620412] wlan: [3925:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 1, Download data len 384756 [ 85.885435] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 85.885499] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 85.890917] usb usb2-port1: cannot disable (err = -32) [ 85.955115] wlan: [3925:I:ANY] ol_target_init: 2505: 6ol_target_init() Download FW done. [ 85.955243] wlan: [3925:I:ANY] ol_ath_copy_tgt_iram: 2335: tgt iram backed up. host paddr 0x87500000 Radio id 0 [ 85.962431] wlan: [3925:I:ANY] htc_wmi_init: 6357: htc_wmi_init() HT Create . cdf8f000 [ 85.973113] wlan: [3925:I:ANY] htc_wmi_init: 6421: [htc_wmi_init:6421] host_enable 0 nss_nwifi_offload 0 [ 85.988878] wlan: [3925:I:ANY] ol_target_init_complete: 6539: CDP soc attach success [ 85.990241] wlan: [3925:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle cdf8f000, ep 2, value 1 [ 85.999212] wlan: [87:I:TIF] init_deinit_sw_version_check: 1734: Firmware_Build_Number:30 [ 86.007235] wlan: [87:E:TIF] init_deinit_populate_fw_version_cmd: 108: failed to save fw version [ 86.015623] wlan: [87:I:TIF] init_deinit_peer_cache_support: 255: Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 [ 86.024299] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 2 idx 0 num_units 53 unit_len 256 [ 86.038313] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 3 idx 1 num_units 53 unit_len 1024 [ 86.048353] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 4 idx 2 num_units 53 unit_len 4096 [ 86.058159] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 8 idx 3 num_units 1 unit_len 327680 [ 86.068050] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 9 idx 4 num_units 1 unit_len 819200 [ 86.077945] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 1 idx 5 num_units 531 unit_len 744 [ 86.087929] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 6 idx 6 num_units 35 unit_len 3072 [ 86.097924] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 7 idx 7 num_units 1 unit_len 6144 [ 86.107804] wlan: [87:I:TIF] init_deinit_mem_mgr_alloc_chunk: 1166: req_id 5 idx 8 num_units 531 unit_len 2084 [ 86.118103] wlan: [87:I:ANY] ol_tx_pflow_ctrl_init: 259: Startup Mode-0 set [ 86.127880] wlan: [87:I:ANY] htt_alloc_peer_map_mem: 141: [ 86.127880] htt_alloc_peer_map_mem : Alloc Success : host q vaddr cf13a000 paddr 8f13a000 [ 86.134343] wlan: [87:I:ANY] htt_alloc_peer_map_mem: 142: [ 86.134343] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts [ 86.157899] wlan: [87:I:ANY] 6 [ 86.157899] <=== cfg max peer id 2080 ====> [ 86.157899] [ 86.162164] wlan: [87:I:ANY] ol_txrx_pdev_attach: 1039: 62500 tx desc's allocated ; range starts from c60e0000 [ 86.171931] wlan: [87:I:TIF] init_deinit_update_pdev_tgt_info: 1082: CDP PDEV ATTACH success [ 86.322202] wlan: [87:E:TIF] init_deinit_ready_event_handler: 464: agile capability disabled in HW [ 86.322423] wlan: [3925:I:ANY] __ol_ath_check_wmi_ready: 5032: ABI Version mismatch: Host(0x3), Target(0x0) [ 86.330210] wlan: [3925:I:ANY] ol_ath_connect_htc: 1235: WMI is ready [ 86.339848] wlan: [3925:E:WMI] event handler already registered 0x8002 [ 86.346423] wlan: [3925:E:WMI] wmi_unified_register_event_handler: Event id 104 is unavailable [ 86.352782] wlan: [3925:E:DIRECT_BUF_RX] direct_buf_rx_target_attach: 146: hal soc or osdev is null [ 86.361607] wlan: [3925:I:ANY] ol_ath_soc_start: 9922: ol_ath_soc_start: Direct Buffer Rx Target Attach Failed [ 86.361607] [ 86.370547] wlan: [3925:I:ANY] htt_h2t_frag_desc_bank_cfg_msg: 217: HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for SoC ID = 0 [ 86.370562] wlan: [0:I:ANY] htt_t2h_msg_handler_misc: 449: 6target uses HTT version 2.2; host uses 2.2 [ 86.402982] wlan: [3925:I:ANY] ol_ath_soc_start: 9993: BURSTING enabled by default [ 86.403379] wlan: [3925:I:ANY] ol_txrx_mgmt_tx_cb_set: 3436: >>>> CB Set 00000000 [ 86.410629] wlan: [3925:I:ANY] ol_ath_stats_attach: 2134: periodic_chan_stats: 1 [ 86.418450] wlan: [3925:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 2099: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5 [ 86.418450] [ 86.426488] wlan: [3925:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11 [ 86.442722] wlan: [3925:I:ANY] ol_ath_soc_start: 10086: ol_ath_soc_start[10086] WAPI MBSSID 2 [ 86.451101] wlan: [3925:I:ANY] ol_ath_update_fw_adfs_support: 286: ol_ath_update_fw_adfs_support: Returning due to null table [ 86.458879] wlan: [3925:I:ANY] smart_log_init: 1616: Smart logging Enabled buf=c6140000 (size=65536) [ 86.469904] wlan: [3925:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3455: pdev_idx = 0 tx_desc_limit = 0 [ 86.479165] wlan: [3925:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(c8fe9a04) is_primary 1 [ 86.488615] wlan: [3925:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3424: Running with HW mode = 7 [ 86.783110] wlan: [3994:I:ANY] osifp_create_wlan_vap: 10411: VDEV Create 94:83:c4:04:07:63 [ 86.783289] wlan: [3994:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 86.790544] wlan: [3994:I:ANY] wlan_vap_create: 1603: enter. devhandle=0xca380500, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 86.790544] [ 86.799944] wlan: [3994:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 86.811782] wlan: [3994:I:ANY] MBO Initialized [ 86.818499] wlan: [3994:I:ANY] OCE Initialized [ 86.822968] wlan: [3994:I:ANY] wlan_vap_create: 1636: exit [ 86.827391] wlan: [3994:E:ANY] Smart Antenna is not supported [ 86.833508] wlan: [3994:E:ANY] Smart Antenna is not supported [ 86.838742] wlan: [3994:I:ANY] osif_create_vap_complete: 10609: TX Checksum:1|SG:1|TSO:1|LRO:1 [ 86.851167] wlan: [3994:I:ANY] VAP device ath18 created osifp: (cd10c500) os_if: (c6150000) [ 86.982586] wlan: [87:E:ANY] [soc0] FWLOG: [2241] WAL_DBGID_RST_STATS ( 0x1, 0x1, 0x96c, 0x0, 0x416064) [ 86.982586] [ 86.982755] wlan: [87:E:ANY] [soc0] FWLOG: [2281] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0) [ 86.982755] [ 86.999649] wlan: [87:E:ANY] [soc0] FWLOG: [2281] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0) [ 86.999649] [ 87.003956] wlan: [87:E:ANY] [soc0] FWLOG: [2281] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0) [ 87.003956] [ 87.017673] wlan: [87:E:ANY] [soc0] FWLOG: [2281] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0) [ 87.017673] [ 87.245810] wlan: [4049:E:mlme] IF_STOP: V:0 Serialization queue disable [ 87.251297] wlan: [4049:I:ANY] ieee80211_node_latevdetach: vap still has nodes, vap->iv_node_count: 1, refcnt: 0xffffffff [ 87.251297] [ 87.251624] ieee80211_mbo_vdetach: MBO terminated [ 87.264179] ieee80211_oce_vdetach: OCE terminated [ 87.269833] wlan: [4049:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 25 [ 87.273647] wlan: [4049:I:ANY] ol_ath_soc_stop: 9653: Suspending Target soc=caa40500 [ 87.280999] wlan: [4049:I:ANY] wlan_pdev_operation: 847: wlan_pdev_operation: disable_target_intr val is 1 [ 87.288774] wlan: [4049:I:ANY] ol_ath_soc_stop: 9656: ol_ath_soc_stop: waiting for target paused event from target [ 87.298243] wlan: [4049:I:ANY] ol_ath_soc_stop: 9682: disable dp interrupts:: soc: cba05380 [ 87.311808] wlan: [4049:I:ANY] 6ol_tx_me_exit: Already Disabled !!! [ 87.311808] [ 87.319205] wlan: [4049:E:WMI] send_thermal_mitigation_param_cmd_non_tlv:3014, htc_send_pkt failed, status:4 [ 87.324684] wlan: [4049:E:WMI] Failed to send WMI_TT_SET_CONF_CMDID [ 87.334876] wlan: [4049:E:WMI] Event id 104 is unavailable [ 87.340742] wlan: [4049:I:ANY] smart_log_deinit: 1747: smart_log_deinit: Smart logging Disabled [ 87.371931] wlan: [4049:I:ANY] ieee80211_cbs_init [ 87.371969] wlan: [4049:I:ANY] CBS Inited [ 87.371969] [ 87.376515] wlan: [3083:I:ANY] ol_acfg_handle_wifi_ioctl: 417: ol_acfg_handle_wifi_ioctl: req->cmd=75 not valid for radio interface, it's for VAP [ 87.413816] wlan: [4074:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 [ 87.413917] wlan: [4074:I:ANY] osifp_create_wlan_vap: 10411: VDEV Create 94:83:c4:04:07:62 [ 87.424944] wlan: [4074:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 87.433095] wlan: [4074:I:ANY] wlan_vap_create: 1603: enter. devhandle=0xcb380500, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 87.433095] [ 87.441924] wlan: [4074:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 87.454373] wlan: [4074:I:ANY] MBO Initialized [ 87.461206] wlan: [4074:I:ANY] OCE Initialized [ 87.465661] wlan: [4074:I:ANY] wlan_vap_create: 1636: exit [ 87.470914] wlan: [4074:E:ANY] Smart Antenna is not supported [ 87.475947] wlan: [4074:E:ANY] Smart Antenna is not supported [ 87.481348] wlan: [4074:I:ANY] osif_create_vap_complete: 10609: TX Checksum:1|SG:1|TSO:1|LRO:1 [ 87.488649] wlan: [4074:I:ANY] VAP device ath0 created osifp: (cd305500) os_if: (ca9e0000) [ 88.975870] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 88.975946] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 88.981344] usb usb2-port1: cannot disable (err = -32) [ 90.380557] 8021q: adding VLAN 0 to HW filter on device ath0 [ 90.405326] device ath0 entered promiscuous mode [ 90.405484] br-lan: port 2(ath0) entered forwarding state [ 90.409054] br-lan: port 2(ath0) entered forwarding state [ 90.416223] wlan: [2160:I:ANY] wlan_cfg80211_do_acs: 3497: vap-0(ath0):ACS Params [ 90.419708] wlan: [2160:I:ANY] wlan_cfg80211_do_acs: 3500: ht_enabled:1|ht40_enabled:0|vht_enabled:0|hw_mode:13|chwidth:20| [ 90.428762] wlan: [2160:I:ANY] ieee80211_autoselect_infra_bss_channel: 3995: ACS started: vap:0xca9e0000 [ 90.980619] wlan: [87:I:ANY] FWLOG: [6509] [ 90.980689] wlan: [87:I:ANY] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 90.980689] [ 90.983696] wlan: [87:E:ANY] [soc0] FWLOG: [6509] WAL_DBGID_RST_STATS ( 0x2, 0x80, 0x96c, 0x0, 0x416064) [ 90.983696] [ 90.997604] wlan: [87:I:ANY] FWLOG: [6818] [ 91.011407] wlan: [87:I:ANY] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 91.011407] [ 91.988429] wlan: [6:I:ANY] FWLOG: [7133] [ 91.988472] wlan: [6:I:ANY] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 91.988472] [ 91.991476] wlan: [6:I:ANY] FWLOG: [7447] [ 92.004871] wlan: [6:I:ANY] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 92.004871] [ 92.005068] wlan: [6:I:ANY] FWLOG: [7760] [ 92.015848] wlan: [6:I:ANY] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 92.015848] [ 92.018732] wlan: [6:I:ANY] FWLOG: [8075] [ 92.028713] wlan: [6:I:ANY] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 92.028713] [ 92.065699] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 92.065788] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 92.072422] usb usb2-port1: cannot disable (err = -32) [ 92.405374] br-lan: port 2(ath0) entered forwarding state [ 92.988202] wlan: [87:I:ANY] FWLOG: [8389] [ 92.988246] wlan: [87:I:ANY] WAL channel change freq=2442, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 92.988246] [ 92.991256] wlan: [87:I:ANY] FWLOG: [8703] [ 93.001531] wlan: [87:I:ANY] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 93.001531] [ 93.005052] wlan: [87:I:ANY] FWLOG: [9017] [ 93.015583] wlan: [87:I:ANY] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 93.015583] [ 93.114497] wlan: [5149:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode [ 93.120472] wlan: [5149:I:ANY] qca_napi_create: 369: qca_napi_create: napi instance 32 created on pipe 4 [ 93.121032] wlan: [5149:I:ANY] ol_target_init: 2453: 6ol_target_init() BMI inited. [ 93.130740] wlan: [5149:I:ANY] ol_target_init: 2467: 6ol_target_init() BMI Get Target Info. [ 93.138002] wlan: [5149:I:ANY] ol_target_init: 2474: Chip id: 0x10, chip version: 0x1000000 [ 93.146631] wlan: [5149:I:ANY] ol_ath_host_config_update: 5175: 6 [ 93.146631] CE WAR Disabled [ 93.146631] [ 93.154877] wlan: [5149:I:ANY] ol_ath_configure_target: 559: 6NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 93.165695] wlan: [5149:I:ANY] ol_target_init: 2496: 6ol_target_init() configure Target . [ 93.175407] wlan: [5149:I:ANY] ol_ath_download_firmware: 1929: [ 93.175407] Target Version is 1000000 [ 93.183321] wlan: [5149:I:ANY] ol_ath_download_firmware: 1939: [ 93.183321] Flash Download Address c0000 [ 93.193085] wlan: [5149:I:ANY] ol_transfer_bin_file: 1401: ol_transfer_bin_file: flash data file defined [ 93.202995] wlan: [5149:I:ANY] ol_transfer_bin_file: 1546: ol_transfer_bin_file[1546] Get Caldata for soc1. [ 93.212859] wlan: [5149:I:ANY] qc98xx_verify_checksum: 800: qc98xx_verify_checksum: flash checksum passed: 0x3872 [ 93.222402] wlan: [5149:I:ANY] ol_transfer_bin_file: 1601: ol_transfer_bin_file 1601: Download Flash data len 12064 [ 93.232872] wlan: [5149:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 93.262409] wlan: [5149:I:ANY] ol_ath_download_firmware: 1947: [ 93.262409] Board data initialized [ 93.262584] wlan: [5149:I:ANY] ol_ath_download_firmware: 1962: 6ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 [ 93.270689] wlan: [5149:I:ANY] ol_transfer_bin_file: 1007: 6 [ 93.270689] Selecting OTP binary for CHIP Version -807439236 [ 93.283036] wlan: [5149:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 93.311265] wlan: [5149:I:ANY] ol_ath_download_firmware: 1991: 6 [ 93.311265] First OTP send param 8000 [ 93.316012] wlan: [5149:I:ANY] ol_ath_download_firmware: 1997: ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 [ 93.320189] wlan: [5149:I:ANY] ol_ath_download_firmware: 2017: ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 [ 93.334694] wlan: [5149:I:ANY] ol_ath_download_firmware: 2085: 6ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 [ 93.344717] wlan: [5149:I:ANY] boardid_to_filename: 426: [ 93.344717] soc1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin [ 93.356349] wlan: [5149:I:ANY] ol_transfer_bin_file: 1397: ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin [ 93.370355] wlan: [5149:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 3, Download data len 12064 [ 93.385849] wlan: [5149:I:ANY] ol_transfer_bin_file: 1713: 6Board extended Data download address: 0x0 [ 93.416827] wlan: [5149:I:ANY] ol_ath_download_firmware: 2103: 6ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 93.416884] wlan: [5149:I:ANY] ol_transfer_bin_file: 1007: 6 [ 93.416884] Selecting OTP binary for CHIP Version -807439236 [ 93.427993] wlan: [5149:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 0, Download data len 4712 [ 93.455813] wlan: [5149:I:ANY] ol_ath_download_firmware: 2119: [ 93.455813] [Flash] : Ignore Module param [ 93.455876] wlan: [5149:I:ANY] ol_ath_download_firmware: 2150: 6 [ 93.455876] Second otp download Param 10000 [ 93.475319] wlan: [5149:I:ANY] ol_ath_download_firmware: 2156: ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 [ 93.475423] wlan: [5149:I:ANY] ol_transfer_bin_file: 1141: 6 [ 93.475423] Mission mode: Firmware CHIP Version -807439236 [ 93.488744] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:206391 size_left:206411 dma_size_left:262144 fw_temp:d3481004 fw_entry_size:206415 [ 93.499313] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2943: ol_swap_wlan_memory_expansion: dma_virt_addr :d2681000 fw_temp: d3481008 length: 206391 [ 93.516517] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2952: 6Swap: bytes_left to copy: fw:16; dma_page:55753 [ 93.516517] [ 93.529885] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2923: ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:55753 fw_temp:d34b3643 fw_entry_size:206415 [ 93.541874] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2926: 6Swap: wrong length read:0 [ 93.541874] [ 93.557769] wlan: [5149:I:ANY] ol_swap_wlan_memory_expansion: 2970: 6ol_swap_wlan_memory_expansion: Swap total_bytes copied: 206391 Target address 417d30 [ 93.557769] [ 93.568203] wlan: [5149:I:ANY] ol_transfer_swap_struct: 2742: 6soc=caa40500 target_write_addr=417d30 seg_info=ca9fc3d0 [ 93.583490] wlan: [5149:I:ANY] ol_transfer_swap_struct: 2748: 6ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 [ 93.594352] wlan: [5149:I:ANY] ol_ath_code_data_swap: 2854: 6bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin [ 93.607718] wlan: [5149:I:ANY] ol_transfer_bin_file: 1209: ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [ 93.622908] wlan: [5149:I:ANY] ol_transfer_bin_file: 1429: 6ol_transfer_bin_file 1429: downloading file 1, Download data len 384756 [ 93.813485] wlan: [1572:E:ANY] ol_ath_get_chan_grade_info: 5620: RF characterization entries is empty [ 93.814162] wlan: [1572:I:ANY] vap-0(ath0): ACS result PCH 11, SCH 7, hw_mode 1 chwidth 40, vht_seg0 9, vht_seg1 0 [ 93.821901] wlan: [1572:I:ANY] ieee80211_acs_scan_evhandler: 3732: lock held duration: 8(ms) [ 93.987675] wlan: [87:I:ANY] FWLOG: [9332] [ 93.987714] wlan: [87:I:ANY] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 93.987714] [ 93.990727] wlan: [87:I:ANY] FWLOG: [9646] [ 94.000738] wlan: [87:I:ANY] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1 [ 94.000738]


[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.154 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: GL.iNet GL-AP1300 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 65024 [ 0.000000] Normal zone: 576 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65024 pages, LIFO batch:15 [ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440 [ 0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64448 [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 248624K/260096K available (5786K kernel code, 189K rwdata, 872K rodata, 1024K init, 241K bss, 11472K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from 0xc0a00bbc with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000009] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000023] Switching to timer-based delay loop, resolution 20ns [ 0.000233] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000251] pid_max: default: 32768 minimum: 301 [ 0.000457] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000474] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001487] CPU: Testing write buffer coherency: ok [ 0.002533] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.002671] rcu: Hierarchical SRCU implementation. [ 0.003111] smp: Bringing up secondary CPUs ... [ 0.006227] smp: Brought up 1 node, 4 CPUs [ 0.006247] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.006256] CPU: All CPU(s) started in SVC mode. [ 0.010828] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.010990] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.011017] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.011240] pinctrl core: initialized pinctrl subsystem [ 0.012268] NET: Registered protocol family 16 [ 0.012629] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.013891] cpuidle: using governor ladder [ 0.013940] cpuidle: using governor menu [ 0.034046] cryptd: max_cpu_qlen set to 1000 [ 0.037400] usbcore: registered new interface driver usbfs [ 0.037473] usbcore: registered new interface driver hub [ 0.037534] usbcore: registered new device driver usb [ 0.037584] pps_core: LinuxPPS API ver. 1 registered [ 0.037595] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.037629] PTP clock support registered [ 0.038319] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.039478] clocksource: Switched to clocksource arch_sys_counter [ 0.040411] thermal_sys: Registered thermal governor 'step_wise' [ 0.040707] NET: Registered protocol family 2 [ 0.040876] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.041636] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.041681] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.041719] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.041766] TCP: Hash tables configured (established 2048 bind 2048) [ 0.041888] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.041928] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.042174] NET: Registered protocol family 1 [ 0.042218] PCI: CLS 0 bytes, default 64 [ 0.044151] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.049973] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.049989] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.101662] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.105045] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.105064] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.105760] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.105870] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.105968] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.106050] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.106359] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.108270] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.108318] msm_serial 78af000.serial: uartclk = 1843200 [ 0.108374] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.108402] msm_serial: console setup on port #0 [ 0.609475] printk: console [ttyMSM0] enabled [ 0.614384] msm_serial: driver initialized [ 0.623483] loop: module loaded [ 0.624512] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 0.632185] random: fast init done [ 0.635383] spi-nor spi0.0: w25q32 (4096 Kbytes) [ 0.635989] 8 fixed-partitions partitions found on MTD device spi0.0 [ 0.640740] Creating 8 MTD partitions on "spi0.0": [ 0.647057] 0x000000000000-0x000000040000 : "SBL1" [ 0.652609] 0x000000040000-0x000000060000 : "MIBIB" [ 0.657233] 0x000000060000-0x0000000c0000 : "QSEE" [ 0.662164] 0x0000000c0000-0x0000000d0000 : "CDT" [ 0.666898] 0x0000000d0000-0x0000000e0000 : "DDRPARAMS" [ 0.671729] 0x0000000e0000-0x0000000f0000 : "APPSBLENV" [ 0.676662] 0x0000000f0000-0x000000170000 : "APPSBL" [ 0.681983] 0x000000170000-0x000000180000 : "ART" [ 0.687838] spi-nand spi0.1: GigaDevice SPI NAND was found. [ 0.690953] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 0.696658] 1 fixed-partitions partitions found on MTD device spi0.1 [ 0.704637] Creating 1 MTD partitions on "spi0.1": [ 0.711055] 0x000000000000-0x000008000000 : "ubi" [ 1.155454] libphy: ipq4019_mdio: probed [ 1.180606] ESS reset ok! [ 1.204913] ESS reset ok! [ 1.626923] libphy: Fixed MDIO Bus: probed [ 1.734454] i2c /dev entries driver [ 1.736436] sdhci: Secure Digital Host Controller Interface driver [ 1.736753] sdhci: Copyright(c) Pierre Ossman [ 1.743084] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.751014] NET: Registered protocol family 10 [ 1.754511] Segment Routing with IPv6 [ 1.757495] NET: Registered protocol family 17 [ 1.761245] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.765499] 8021q: 802.1Q VLAN Support v1.8 [ 1.778754] Registering SWP/SWPB emulation handler [ 1.792085] UBI error: cannot open mtd rootfs, error -2 [ 1.792135] ubi0: attaching mtd8 [ 2.537647] random: crng init done [ 5.474751] ubi0: scanning is finished [ 5.515125] ubi0 warning: 0xc067d104: cannot reserve enough PEBs for bad PEB handling, reserved 10, need 19 [ 5.518063] ubi0: attached mtd8 (name "ubi", size 128 MiB) [ 5.523882] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.529273] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.536204] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.543050] ubi0: good PEBs: 1023, bad PEBs: 1, corrupted PEBs: 0 [ 5.549817] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 5.556012] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1635066095 [ 5.563195] ubi0: available PEBs: 0, total reserved PEBs: 1023, PEBs reserved for bad PEB handling: 10 [ 5.572550] ubi0: background thread "ubi_bgt0d" started, PID 105 [ 5.574784] block ubiblock0_1: created from ubi0:1(rootfs) [ 5.587672] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 5.593000] hctosys: unable to open rtc device (rtc0) [ 5.600067] clk: Not disabling unused clocks [ 5.619432] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 5.621119] Freeing unused kernel memory: 1024K [ 5.639831] Run /sbin/init as init process [ 6.538430] init: Console is alive [ 6.538687] init: - watchdog - [ 8.278335] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.473070] dwc3-qcom 8af8800.usb3: IRQ hs_phy_irq not found [ 8.473109] dwc3-qcom 8af8800.usb3: IRQ dp_hs_phy_irq not found [ 8.477804] dwc3-qcom 8af8800.usb3: IRQ dm_hs_phy_irq not found [ 8.483497] dwc3-qcom 8af8800.usb3: IRQ ss_phy_irq not found [ 8.491034] dwc3-qcom 60f8800.usb2: IRQ hs_phy_irq not found [ 8.495253] dwc3-qcom 60f8800.usb2: IRQ dp_hs_phy_irq not found [ 8.500941] dwc3-qcom 60f8800.usb2: IRQ dm_hs_phy_irq not found [ 8.506536] dwc3-qcom 60f8800.usb2: IRQ ss_phy_irq not found [ 8.514608] dwc3 8a00000.dwc3: Failed to get clk 'ref': -2 [ 8.634593] dwc3 6000000.dwc3: Failed to get clk 'ref': -2 [ 8.754561] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 8.754631] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 8.759190] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f665 hci version 0x100 quirks 0x0000000002010010 [ 8.766685] xhci-hcd xhci-hcd.0.auto: irq 93, io mem 0x08a00000 [ 8.776144] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 8.781829] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 8.787347] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 8.795705] hub 1-0:1.0: USB hub found [ 8.801599] hub 1-0:1.0: 1 port detected [ 8.805700] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.809892] hub 2-0:1.0: USB hub found [ 8.817519] hub 2-0:1.0: 1 port detected [ 8.824016] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 8.825031] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 8.830597] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010 [ 8.837931] xhci-hcd xhci-hcd.1.auto: irq 94, io mem 0x06000000 [ 8.847454] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 8.853175] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 8.858705] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 8.867193] hub 3-0:1.0: USB hub found [ 8.872924] hub 3-0:1.0: 1 port detected [ 8.877014] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.883201] hub 4-0:1.0: USB hub found [ 8.888786] hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 8.894591] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 8.901500] init: - preinit - [ 9.129634] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 9.159774] usb 3-1: new full-speed USB device number 2 using xhci-hcd [ 10.374810] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 13.562607] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 14.773450] UBIFS (ubi0:2): default file-system created [ 14.776035] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 14.777762] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 205 [ 15.105539] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 15.105589] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 15.112473] UBIFS (ubi0:2): FS size: 119357440 bytes (113 MiB, 940 LEBs), journal size 5967872 bytes (5 MiB, 47 LEBs) [ 15.122299] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB) [ 15.132884] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 2CB139FE-D463-4CC6-9AEF-8271825F9A5B, small LPT model [ 15.144543] mount_root: overlay filesystem has not been fully initialized yet [ 15.151174] mount_root: switching to ubifs overlay [ 15.167119] urandom-seed: Seed file not found (/etc/urandom.seed) [ 15.257596] procd: - early - [ 15.257714] procd: - watchdog - [ 15.873613] procd: - watchdog - [ 16.865841] procd: - ubus - [ 16.923952] procd: - init - [ 17.435303] kmodloader: loading kernel modules from /etc/modules.d/* [ 17.443876] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35 [ 17.443918] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32 [ 17.461904] xt_time: kernel timezone is -0000 [ 17.476979] urngd: v1.0.2 started. [ 17.500928] PPP generic driver version 2.4.2 [ 17.501875] NET: Registered protocol family 24 [ 18.840135] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 19.062391] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000 [ 19.062441] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 19.073940] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 19.127034] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 50480c1b [ 20.414565] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 20.414611] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 20.462349] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 20.463887] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 20.614652] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 20.782342] ath: EEPROM regdomain sanitized [ 20.782357] ath: EEPROM regdomain: 0x64 [ 20.782362] ath: EEPROM indicates we should expect a direct regpair map [ 20.782374] ath: Country alpha2 being used: 00 [ 20.782378] ath: Regpair used: 0x64 [ 21.900582] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000 [ 21.900631] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 21.913298] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 21.964567] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 50480c1b [ 23.159658] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 23.252175] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 23.252224] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 23.299777] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 23.301726] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 23.439410] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 23.597476] ath: EEPROM regdomain sanitized [ 23.597491] ath: EEPROM regdomain: 0x64 [ 23.597496] ath: EEPROM indicates we should expect a direct regpair map [ 23.597508] ath: Country alpha2 being used: 00 [ 23.597512] ath: Regpair used: 0x64 [ 23.604908] kmodloader: done loading kernel modules from /etc/modules.d/* [ 27.509826] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 31.849619] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 35.778471] br-lan: port 1(eth0) entered blocking state [ 35.778512] br-lan: port 1(eth0) entered disabled state [ 35.782963] device eth0 entered promiscuous mode [ 35.901459] ess_edma c080000.edma eth1: Link is Down [ 36.169950] usb usb2-port1: Cannot enable. Maybe the USB cable is bad? [ 36.809577] br-lan: port 1(eth0) entered blocking state [ 36.809624] br-lan: port 1(eth0) entered forwarding state [ 36.814377] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Space for additional notes, links to forum threads or other resources.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/10/10 16:50
  • by rollingstar