Draytek Vigor2830 Series
Supported Versions
| Version/Model | Launch Date | S/N | OpenWrt Version Supported | Model Specific Notes |
|---|---|---|---|---|
| Vigor2830 | 2012 | - | - | NO WLAN, PSTN/VoIP |
| Vigor2830n | 2012 | - | - | 2.4GHz N |
| Vigor2830Vn | 2012 | - | - | 2.4GHz N and PSTN/VoIP |
| Vigor2830n plus | 2012 | - | - | switchable 2.4GHz - 5GHz N |
| Vigor2830Vn plus | 2012 | - | - | switchable 2.4GHz - 5GHz N and PSTN/VoIP |
NOTE: Anything not included in model specific notes, or where a short comment couldn't be included on the notes.
OEM source code available at: (add URL)
Hardware Highlights
| SoC | Ram | Flash | Network | USB | Serial | JTag |
|---|---|---|---|---|---|---|
| Danube/Danube-S platform | 32MiB | 8MiB | 4 x 1 | Yes | Yes | ? |
Manufacturer's site: http://www.draytek.co.uk/products/business/vigor-2830
Flash Layout
Please check out the article flash.layout. It contains an example and a couple of explanations.
start end what 00000000 0FFFFFFF RAM (up to 256MB address space) 10000000 13FFFFFF ROM (up to 64MB address space) 14000000 14000FFF external bus general purpose i/o 18000300 180003FF general purpose timer 1E100400 1E1007FF first serial port 1E100800 1E1008FF SSC (what's that) 1E100B10 1E100B3F GPIO bank 0 1E100B40 1E100B6F GPIO bank 0 1E100B70 1E100B9F GPIO bank 0 1E100BB0 1E100BEF serial/parallel converter 1E100C00 1E100FFF second serial port 1E103100 1E1031FF hardware crypto 1E104100 1E1041FF dma controller 1E105300 1E1053FF external bus controller 1E105400 1E1057FF PCI bus controller 1E116000 1E117000 DSL interface 1E180000 1E1BFFFF ethernet controller 1F101000 1F101FFF external interrupt controller 1F102000 1F102FFF power management controller 1F103000 1F103FFF clock generator 1F107000 1F107FFF multi-processsing 1F203000 1F203FFF reset controller 1F880200 1F8802FF interrupt controller 1F8803F0 1F8803FF watchdog timer
Specific Configuration
Interfaces
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| br-lan | LAN & WiFi | 192.168.1.1/24 |
| vlan0 (eth0.0) | LAN ports (1 to 4) | None |
| vlan1 (eth0.1) | WAN port | DHCP |
| wl0 | WiFi | Disabled |
Switch Ports (for VLANs)
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
| Port | Switch port |
|---|---|
| Internet (WAN) | 4 |
| LAN 1 | 3 |
| LAN 2 | 2 |
| LAN 3 | 1 |
| LAN 4 | 0 |
Failsafe mode
Buttons
→ hardware.button on howto use and configure the hardware button(s).
The Vigor2830 series has two buttons. They are Reset and Wifi Toggle. Here, we merely name the buttons, so we can use them in the above Howto:
| BUTTON | Event |
|---|---|
| Reset | reset |
| Wifi Toggle | wifitoggle |
Hardware
Vigor2830 Series, n ,Vn
| Instruction set | MIPS |
|---|---|
| Vendor | Lantiq |
| bootloader | U-Boot |
| System-On-Chip | Danube/Danube-S platform  |
| CPU @Frq | |
| Flash size | 8192 KiB |
| Flash Chip | |
| RAM size | 32 MiB |
| RAM Chip | Nanya NT5DS16M16CS-5T |
| Wireless No1 | distinct Chip: Ralink RT28xx (RT2860) w/ 2T3R MIMO for 2.4GHz 802.11b/g/n |
| switch | GigabitEthernet |
| Modem | ADSL/ADSL2+ |
| USB | Yes 1 x 2.0 |
| Serial | Yes |
| JTAG | No |
Vigor2830n H/W:V1 MODULE:6 (single band)
| Instruction set | MIPS |
|---|---|
| Vendor page | DRAYTEK |
| Vendor support page | FIRMWARE |
| bootloader | Dray-Boot |
| System-On-Chip | AMAZON-S PSB 50610 E V1.4 |
| CPU @Frq | 333 Mhz |
| Flash size | 8192 KiB |
| Flash Chip | Macronix MX29LV640EBTI-70G |
| RAM size | 32 MiB |
| RAM Chip | Nanya NT5DS32M16CS-5T |
| Wireless No1 | RT2860 (RT2860T) |
| switch | AR8316 (AR8316-AK1E) |
| Modem | ADSL/ADSL2+ |
| USB | Yes 1 x 2.0 |
| Serial | Yes |
| JTAG | Yes |
LED & BUTTON
Gpio Expander U39 cascading U53 74x595 (74HC595) Linux driver gpio-74x164.c ? U39 to Led: ACT-(Q1) WLAN -(Q8) DoS-(Q5) USB-(Q6) DSL -(??) VPN-(Q3) CSM-(Q2) WLAN2-(??) QoS-(Q4) U39 to Cpu: IN - (gpio ??) CLK - (gpio ??) LATCH- (gpio ??) RST - (gpio ??) U39 to U53: OUT - IN CLK - CLK LATCH- LATCH RST - RST Button: WPS (gpio ??) Reset (gpio ??) ---------------- 74HCT595 74LV595 74HCT594 74LV594 74x594 74HC594 74HCT164 74LV164 74x164 74HC164
CPU INFO
chipid = 0x50110083 CPU revision = 0x00019641 prom.c: case SOC_ID_AMAZON_S: lantiq_soc.h: #define SOC_ID_AMAZON_S 0x110 /* 50610 */
FW update & flash information
The loader accepts the following file names: V2830_xxxxx.all kernel + fs V2830_xxxxx.rst kernel + fs + settings V2830_xxxxx.000 ??? V2830_xxxxx.bin ??? V2830_xxxxx.web ??? V2830_xxxxx.cfg ??? V2830_xxxxx.mdm ??? V2830_xxxxx.xxx ??? fw update structure: 0x000: xx xx xx xx part length 0x004: ufo byte 0x50 or 0x10 0x005: xx xx xx part length - 0xС 0x006: magic "rDkmfaaryTedecz" .... 0x100: kernel xx xx xx xx .... last 16 bytes of file 00 00 00 44 5C 00 11 00 ¦ 00 00 30 21 A1 94 6E D0 00 00 00 A0 5C 00 11 00 ¦ 00 14 AC E6 E3 3E 7D 2C 00 00 00 41 5C 00 11 00 ¦ 00 BF 00 10 B2 34 B4 10 11 00 00 lzo end + last 7 bytes check sum unknown format flash layout: 0x000000 0x007FCF boot 0x007FD0 boot 0x007FD0 0x009FFF boardconfig 0x002030 boardconfig --> 0x007FD8 wpsk password --> 0x007FF8 mac address 0x00A000 0x2FFFFF settings 0x026000 settings 0x300000 0x52FFFF fw part 1 0x500000 kernel 0x530000 0x74FFFF fw part 2 0x220000 fs 0x750000 0x7FFFFF fw part 3 0x0B0000 ufo I have flash dump
Vigor2830n plus, Vn plus
| Instruction set | MIPS |
|---|---|
| Vendor | Lantiq |
| bootloader | U-Boot |
| System-On-Chip | Danube/Danube-S platform |
| CPU @Frq | |
| Flash size | 8192 KiB |
| Flash Chip | ? |
| RAM size | 32 MiB |
| RAM Chip | Nanya NT5DS16M16CS-5T |
| Wireless No1 | distinct Chip: Ralink RT28xx (RT2860) w/ 2T3R MIMO for 2.4GHz 802.11b/g/n |
| Wireless No2 | distinct Chip: 2T3R MIMO for 5GHz 802.11b/g/n |
| switch | GigabitEthernet |
| Modem | ADSL/ADSL2+ |
| USB | Yes 1 x 2.0 |
| Serial | Yes |
| JTAG | No |
Photos
Model Number
Front:
Photo of front of the casing
Back:
Photo of back of the casing
Opening the case
Main PCB Vigor2830n H/W:V1 MODULE:6 (single band)
BootSel
found only BootSel2, there is no way to find BootSel0
Bootstrap: boot_sel2 boot_sel1 boot_sel0 0 0 1 external parallel flash (default) 1 0 0 UART1 1 0 1 serial SPI (found)
Serial
JTAG
J3 X X X X 1 X X X X TMS TDO TDI TRST TCK ??? 3.3 GND
Debricking
Bootloader Mods
Currently none.
Bootlogs
OEM bootlog
PUT HERE YOUR BOOTLOG
OEM bootlog Vigor2830n H/W:V1 MODULE:6 (single band)
ROM VER: 1.0.3 CFG 01 Readà ROM VER: 1.0.3 CFG 01 Read EEPROMX X relocate_code start relocate code finish Go... IO_Port_Init!! Detect existed devices!!Modes: __STDC__ 32-bit mwDWORD==(unsigned long) mwROUNDALLOC==4 sizeof(mwData)==24 mwDataSize==24 statistics: now collecting on a line basis ============= Memwatch Auto Self Test ============= Normal Free...DETECTED Double Free...DETECTED NULL Free.....DETECTED Wild Free.....DETECTED Underflow.....DETECTED Overflow......DETECTED Unfree 1......DETECTED Unfree 2......DETECTED ALL TEST OK! Please be assured that all test buffers have freed. Slab kmalloc range: [0x80A4EDE8:0x8114FDE7](size=7344127 bytes) Linear malloc range: [0x8219A670:0x83EFF000](size=30820752 bytes) !!! Maxi malloc size =2072598040 (st=86699e8, end=83eff000)!!!! init cpu_wait to r4k_wait()!! trap_init() doneTODO: chip version danube_setup() donemips_hpt_frequency:166666667 r4k_offset: 00196e6a(1666666) Using 166.667 MHz high precision timer. c0_hpt_timer_init()..count=-2086036903. time_init()... dma_init() done init_IRQ() partial done skb_init() doneCPU revision is: 00019641 cpu_report() donePrimary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. cache_init() donePCI: Probing PCI hardware on host bus 0. Autoconfig PCI channel 0x808f4b80 Scanning bus 00, I/O 0x1ae00000:0x1b000001, Mem 0x18000000:0x1a000001 00:0e.0 Class 0280: 1814:0601 Mem at 0x18000000 [size=0x10000] Scanning bus 00 Found 00:70 [1814/0601] 000280 00 slot:func=00:0e.0 PCI device 1814:0601 PCI_HEADER_TYPE_NORMAL sub vid=1814 did=2860 Fixups for bus 00 Bus scan for 00 returning with max=00 pci_init()...<6>led: misc_register on minor = 151 danube_led_init() done!!!<5>IFX DEU DES initialized (multiblock) (DMA). Copyright (c) 2007-2008 Infineon. <5>IFX DEU AES initialized (multiblock) (DMA). Copyright (c) 2007-2008 Infineon. <3>IFX AES initialization failed! <5>IFX DEU SHA1 initialized (DMA). <3>IFX SHA1 initialization failed! <5>IFX DEU MD5 initialized (DMA). <3>IFX MD5 initialization failed! DEU init done!! Enable IE!!! ISDN:StartUp>ISDN H/W Initialize ....Fail to write ISDN register : R_RAM_DATA >>>>>> ISDN detected Fail !!! vendor_id: 1814,device_id: 601 === pAd = 82e578d0, size = 631584 === <-- RTMPAllocAdapterBlock, Status=0 danube MAC driver loaded! switch_devs=0 name =eth%d . danube_switch_init() ok. Initial_wlan_request_irq....RX DESC a2f03660 size = 4096 <-- RTMPAllocTxRxRingMemory, Status=0 <<<pAd->CommonCfg.PhyMode=9>>> **************wds_init************** 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff ff ff 00 01 Main bssid = 00:50:7f:e8:91:98 <==== rt28xx_init, Status=0 0x1300 = 00064300 IFX MEI Version 3.05.00 <3>[IFX_MEI_InitProcFS 3226]: Failed to create /proc/ danube_mei <6>../usb/usb.c: registered new driver hub usb_init() done!! usb_host_init[0]!! run usb otg driver!! DANUBE_MPS_CHIPID=50110083, Chip Version Number=5, Part Number=110, Manufacturer ID=41 ** VpnCapabilities() is 1 ** Linear free(0x82f04870), Ln:56! @@@@@ Inside InitIpAddrTable() @@@@@ [2;5HVigor2830 by DrayTek Corp.[3;5H==========================[4;5HLAN MAC Address : 00-50-7F-E8-91-98[5;5HIP Address : 192.168.1.1[6;5HIP Subnet Mask : 255.255.255.0[7;5HFirmware Version : 3.6.6.2_sb_2471201[9;5H-------- Main Menu --------[10;5H1 : Change IP Address and Subnet Mask[11;5H2 : Change Administrator Password[12;5H3 : Reboot System[13;5H4 : Enable TFTP Server[14;5H5 : Restore to Default Management Port Please Select Item : athrs16_reg_init complete. c0_hpt_timer_init()..count=-1667284.<6>dwc_otg: version 2.2-RC3 usb_alloc_buf, size=64, totalsize=76, cached=80a51e80<6>dwc_otg_hcd: irq 54, addr be101000 <6>../usb/usb.c: new USB bus registered, assigned bus number 1 Manufacturer: Linux 2.4.31-Danube-3.0.5-G0432V30_BSP dwc_otg_hcd Product: dwc_otg_hcd SerialNumber: dwc_otg_hcd hub_probe <6>../usb/hub.c: USB hub found usb_hub_configure() <6>../usb/hub.c: 1 port detected FILL_INT_URB()usb_hub_power_on() New device : Vendor=0x0, Product=0x0 exit usb_hub_configure()USB device 1 (vend/prod 0x0/0x0) is claimed.<6>DWC_otg: Init: Power Port (0) usb host init done!! <6>../usb/usb.c: registered new driver usblp <6>../usb/printer.c: v0.13: USB Printer Device Class driver usblp_init() done!!!! <6>../usb/usb.c: registered new driver usbminivigor usb_minidrv_init() done!!!! <7>../usb/CDCEther.c: ../usb/CDCEther.c: 0.98.6 7 Jan 2002 Brad Hards and another <6>../usb/usb.c: registered new driver CDCEther <6>../usb/usb.c: registered new driver serial ----------------> usb_serial_register <6>../usb/usbserial.c: USB Serial support registered for Generic <6>../usb/usbserial.c: USB Serial Driver core v1.4 ../usb/wimaxdrv.c: v1.0.0 2009/07/15 Samsung SWC-U200 Wimax driver <6>../usb/usb.c: registered new driver WiMAX/LTE <6>../usb/usb.c: registered new driver Usb Mass Storage ----------------> usb_register cfparse(0) cf_post_config(0) 1 INFO: Server addr pool not properly configured ERR: failed to parse configuration fileppe: ATM init succeeded (firmware version 1.1.0.2.1.13) amazon_set_vpivci: channel=0,vpi=0,vci=26 port=0 amazon_set_qos_aal: channel=0,qos=0,aal_type=6000000 dsl_init() IFXXDSL.C: SetSarConnParam(), ConnNum=0 ======================================= conn->VPI=0, conn->VCI=38, conn->Sar_Port=0, conn->Qos=0x0, conn->AAL_type= 0x6000000 conn->PCR=0, conn->SCR=0, conn->MBS=0 ======================================= -----------yyy--------------------------- tx PCR=0 tx SCR=0 tx MBS=0 tx CDV=0, 0 xdsl drop tick= 501 <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on() <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on() <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on() <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on() <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on() <6>OC INTERRUPT~~<3>DWC_otg: Device Not Supported <3>../usb/hub.c: port 1 over-current change usb_hub_power_on()
OpenWrt bootlog
PUT HERE YOUR BOOTLOG