D-Link DSL-504T C3

This device is NOT RECOMMENDED for future use with OpenWrt due to low flash/ram.
DO NOT BUY DEVICES WITH 4MB FLASH / 32MB RAM if you intend to flash an up-to-date and secure OpenWrt version onto it! See 4/32 warning for details.

1) This device does not have sufficient resources (flash and/or RAM) to provide secure and reliable operation.
This means that even setting a password or changing simple network settings might not be possible any more, rendering the device effectively useless. See OpenWrt on 4/32 devices what you can do now.

2) OpenWrt support for this device has ended in 2022.
19.07.10 was the last official build for 4/32 devices.

This page only refers to generation II devices (marked revision C on the back).

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
C3 10.03.1 Use ar7 generic

NOTE: On trunk builds (and Attitude Adjustment at the moment), the default network configuration won't work (see https://dev.openwrt.org/ticket/13404 to see if it has been fixed). To get it to work, you must build an image manually and modify target/linux/ar7/base-files/etc/config/network. Change the line:

option ifname	"eth0 eth1 eth0.1 eth0.2"

to

option ifname	"eth0"

I did find that changing things in Luci was very slow with Attitude Adjustment and possibly unstable (router seemed to hang after changing things) so I tried with the 3.6.11 Kernel and zram and, so far, I haven't had any problems. This was on trunk revision 36367.

UPDATE: Unfortunately, I have found it to be a bit unreliable. I think that this device is probably too slow and doesn't have enough memory to work well with later kernels so I recommend sticking with 10.03.1.

CPU Ram Flash Network USB Serial JTag
TI AR7 (TNETD7200) 16MiB 4MiB 4 x 1 + ADSL2/2+ No Yes Yes

D-Link DSL-5xxT and DSL-G6xxT - ADAM2 Installation Guide

My router had PSPBoot1.3 and was configured with an IP address of 5.8.8.8.

For the following, I had to hack the ftp client (OS X) I was using so that it handled QUOTE commands as I want (missing line feeds). It’s probably easier to telnet to the device. The ftp client that comes with Linux might not have the same problem.

1. Power on the router.

2. Type “ftp 5.8.8.8” after about a second. Wait and it should connect. I found it pretty easy to connect. User “adam2” password “adam2”.

3. Use the SETENV commands to change flash layout (see dsl-524t). Knowing what I know now, I think the only one that matters is the start and size of mtd1 since that is what PSPBoot uses to boot. I had to change it to start at 0x90020000. The size of mtd1 just has to be big enough to fit your image. See flash layout below. Don't blindly follow these instructions if it looks like your boot and config partitions are in a different place.

4. To put firmware on your router, in ftp type:

 bin
 quote "MEDIA FLSH"
 put <path-to-firmware> "x mtd1"

5. Wait a few seconds after it has finished (important if you doing the above as part of a script) and then:

 quote "REBOOT"

This is in PSPBoot, after changing things. As I said above, the only one that is important is the start of mtd1 and the size has to be sufficient to put your image in it.

 mtd0            0x900b1000,0x903e0000
 mtd1            0x90020000,0x903e0000
 mtd2            0x90000000,0x90010000       # Boot
 mtd3            0x90010000,0x90020000       # Config
 mtd4            0x90020000,0x903e0000

In OpenWrt (note that the names do not match up):

 dev:    size   erasesize  name
 mtd0: 00010000 00002000 "loader"
 mtd1: 00010000 00010000 "config"
 mtd2: 003e0000 00010000 "linux"
 mtd3: 002e4f6b 00010000 "rootfs"
 mtd4: 00120000 00010000 "rootfs_data"
Architecture MIPS
Vendor D-Link
bootloader PSPBoot
System-On-Chip TI AR7
CPU/Speed 211 MHz
Flash-Chip
Flash size 4 MiB
RAM 16 MiB
Ethernet RealTek RTL8306N
Internet ADSL2+ /(3g/LTE over USB port)
USB No
Serial Yes - tested working over TTL converter
JTAG Yes - tested with OpenOCD 0.10.0

Seems to be the same as the DSL-524t.

Tested over OpenOCD.

The DSL-524t appears to be similar.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2019/10/03 18:49
  • by tmomas