ZyXEL VSG1432

CFE version 1.0.37-107.23 for BCM96368 (32bit,SP,BE) Build Date: 06/20/2011 (jhenyang@msgsw4) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name MX29GL128EH, id 0x2221 size 16384KB Total Flash size: 16384K with 128 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Checking Reset button on EXT INTR 0 Checking Reset button on EXT INTR 0 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Boot image (0=latest, 1=previous) : 0 Board Id (0-15) : 96368MVWG Number of MAC Addresses (1-32) : 7 Base MAC Address : b0:b2:00:77:00:00 PSI Size (1-128) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Wait for Multiboot Service Packet... 0 Booting from latest image (0xb8020000) ... Code Address: 0x80020000, Entry Address: 0x80024230 Decompression OK! Entry at 0x80024230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80024230 Linux version 2.6.30 (albert@albert-desktop) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Tue Aug 19 11:31:37 CST 2014 Parallel flash device: name MX29GL128EH, id 0x2221 size 16384KB 96368MVWG prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 03ece000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003ece Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003ece On node 0 totalpages: 16078 free_area_init_node: node 0, pgdat 8037c810, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11888 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15952 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59832k/64312k available (2887k kernel code, 4460k reserved, 562k data, 128k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 net_namespace: 1128 bytes NET: Registered protocol family 16 Total Flash size: 16384K with 128 sectors registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff] pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff] BLOG v3.0 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 116 io scheduler noop registered (default) Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8020100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x5 is enabled SES: LED GPIO 0x1b is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Aug 19 2014 11:28:22 Broadcom Logger v0.1 Aug 19 2014 11:26:33 IPSEC SPU: SUCCEEDED Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 128k freed init started: BusyBox v1.00 (2014.08.19-03:35+0000) multi-call binary BusyBox v1.00 (2014.08.19-03:35+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Oct 19 2010 10:24:26 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Oct 19 2010 10:24:26 Broadcom Packet CMF (Experimental) Char Driver v0.1 Oct 19 2010 10:24:24 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Oct 19 2010 10:24:23 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 Aug 19 2014 11:26:45 ETH Init: 180 tx BDs at 0xa393f000 ETH Init: 400 rx BDs at 0xa39f2000 ETH Init: 400 rx BDs at 0xa39f1000 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Oct 19 2010 10:24:24 Registered Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Oct 19 2010 10:24:24 Registered Broadcom Packet CMF (Experimental) ENABLED. eth0: MAC Address: B0:B2:DC:77:00:00 eth1: MAC Address: B0:B2:DC:77:00:00 eth2: MAC Address: B0:B2:DC:77:00:00 eth3: MAC Address: B0:B2:DC:77:00:00 eth10: MAC Address: B0:B2:DC:77:00:00 No MII transceiver present!. PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl:srom not detected,using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43222_map.bin wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.60.120.11.cpe4.06L03.1 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs p8021ag: p8021ag_init entry Broadcom 802.1Q VLAN Interface, v0.1 237 240 ===== Release Version 4.06L.03 (build timestamp 140819_1133) ===== Wed Jan 1 00:00:00 UTC 2014 ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3840 buckets, 15360 max) xt_time: kernel timezone is -0000 ip6_tables: (C) 2000-2006 Netfilter Core Team dproxy: load nameserver 0.0.0.0 0.0.0.0 dproxy: load domain Home received CMS_MSG_DNSPROXY_RELOAD dproxy: load nameserver 0.0.0.0 0.0.0.0 dproxy: load domain Home Switching back to primary dns server (0.0.0.0). Sntp: Using new rule EST5EDT,M3.2.0/2,M11.1.0/2 dhcpd:error:16.022:set_iface_config_defaults:663:SIOCGIFADDR retry fail again on br0! dhcpd:error:16.024:set_iface_config_defaults:665:...Retry time = 1 received CMS_MSG_DNSPROXY_RELOAD dproxy: load nameserver 0.0.0.0 0.0.0.0 dproxy: load domain Home Switching back to primary dns server (0.0.0.0). received CMS_MSG_DNSPROXY_RELOAD dproxy: load nameserver 0.0.0.0 0.0.0.0 dproxy: load domain Home Switching back to primary dns server (0.0.0.0). ADDRCONF(NETDEV_UP): eth0: link is not ready netdev path : eth0.0 -> eth0 device eth0.0 entered promiscuous mode device eth0 entered promiscuous mode br0: port 1(eth0.0) entering forwarding state device eth0 is not a slave of br0 Created new Tag Rule: dev=eth0, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth0, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth0, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows ADDRCONF(NETDEV_CHANGE): eth0.0: link becomes ready ADDRCONF(NETDEV_UP): eth1: link is not ready netdev path : eth1.0 -> eth1 device eth1.0 entered promiscuous mode mcpd: error can't get ip addr by idxmcpd: can't sbr0: port 1(eth0.0) entering disabled state et IPV6_PKTINFO br0: port 1(eth0.0) entering forwarding state device eth1 entered promiscuous mode br0: port 2(eth1.0) entering forwarding state device eth1 is not a slave of br0 Created new Tag Rule: dev=eth1, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth1, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth1, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows ADDRCONF(NETDEV_UP): eth2: link is not ready netdev path : eth2.0 -> eth2 device eth2.0 entered promiscuous mode br0: port 2(eth1.0) entering disabled state br0: port 1(eth0.0) entering disabled state br0: port 2(eth1.0) entering forwarding state br0: port 1(eth0.0) entering forwarding state device eth2 entered promiscuous mode br0: port 3(eth2.0) entering forwarding state ADDRCONF(NETDEV_CHANGE): eth2.0: link becomes ready ADDRCONF(NETDEV_CHANGE): eth1.0: link becomes ready device eth2 is not a slave of br0 Created new Tag Rule: dev=eth2, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth2, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth2, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows ADDRCONF(NETDEV_UP): eth3: link is not ready netdev path : eth3.0 -> eth3 device eth3.0 entered promiscuous mode br0: port 3(eth2.0) entering disabled state br0: port 2(eth1.0) entering disabled state br0: port 1(eth0.0) entering disabled state br0: port 3(eth2.0) entering forwarding state br0: port 2(eth1.0) entering forwarding state br0: port 1(eth0.0) entering forwarding state device eth3 entered promiscuous mode br0: port 4(eth3.0) entering forwarding state device eth3 is not a slave of br0 Created new Tag Rule: dev=eth3, dir=1, tags=0, id=0 Created new Tag Rule: dev=eth3, dir=1, tags=1, id=0 Created new Tag Rule: dev=eth3, dir=1, tags=2, id=0 Broadcom Packet Flow Cache flushing the flows SIOCGIFFLAGS: No [ERROR vlan] registerVlanDevice,300: Could not find Real Device eth4 such device [ERROR vlan] vlanIoctl ,519: Failed to create VLAN device (eth4, 0) [ERROR vlanctl] vlanCtl_createVlanInterface, 190: No such device ADDRCONF(NETDEV_CHANGE): eth3.0: link becomes ready ssk:error:19.529:rutLan_setupLanVlanDevice:1677:Failed to create eth4.0 ssk:error:19.529:rutEth_setSwitchWanPort:99:ioctl SIOCSWANPORT eth4 returns error! device wl0 entered promiscuous mode br0: port 4(eth3.0) entering disabled state br0: port 3(eth2.0) entering disabled state br0: port 2(eth1.0) entering disabled state br0: port 1(eth0.0) entering disabled state WLmngr Daemon is running optarg=0 shmId=0 br0: port 4(eth3.0) entering forwarding state br0: port 3(eth2.0) entering forwarding state br0: port 2(eth1.0) entering forwarding state br0: port 1(eth0.0) entering forwarding state wlevt_init@107: opened loopback socket 4 wlevt is ready for new msg... br0: port 5(wl0) entering forwarding state *** dslThread dslPid=2216 BcmAdsl_Initialize=0xC017E740, g_pFnNotifyCallback=0xC01B5944 Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 068, PhaseValue = -150, PhaseCntl = 0x7FBD0000 QPROC is aligned, i = 068, PhaseValue = -050, PhaseCntl = 0x7FBD3FBC Clocks for QPROC and AFE are aligned with syn_status AFE = 0x78, QPROC = 0x70 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA3FFFFF8, 0x51555541 0x57551555 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xED1E8 => 0x123BA0 *** AdslCoreSharedMemInit: shareMemSize=58429(58432) AdslCoreHwReset: pLocSbSta=82580000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FAD4B0 ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa25c0000 XTM Init: 100 rx BDs at 0xa3a9c800 ssk:error:21.854:callSetHandlerFunc:725:bug fix: bridge to route PPPoE mode workaround ADDRCONF(NETDEV_UP): eth10: link is not ready PROGRAM : VcAutoHunt main > ENTER ssk:error:24.199:getLanDevIidStackOfBridge:1345:could not find bridge br-1 ssk:error:24.199:rutLan_moveEthInterface:740:could not find toBridgeIfName br-1 WLMNGR-DAEMON:error:418.543:cmsLck_acquireLockWithTimeoutTraced:120:held for -1ms by function cmsMdm_init, ret 9809 Powered up Enable WLAN button in front panel Disable WLAN button '0' Success Enable WLAN button in front panel Disable WLAN button '0' Success Enable WLAN button in front panel Disable WLAN button '0' Success General UPnP daemon is ready to run with NATT 1 vectoringd:error:29.264:initLoggingFromConfig:85:get of VECTORING_CFG object failed, ret=9005 Switch MDK: num_switches = 1 Switch MDK: unit = 0; phy_pbmp = 0x3f; config_pbmp = 0x3f Switch MDK link poll thread: unit=0; phypbmp=0x3f There is no Predefined DevicePin in CFE WPS Device PIN = 10499917 Setting SSID: "ZyXEL22518" Setting SSID: "ZyXEL22518_Guest1" Setting SSID: "ZyXEL22518_Guest2" Setting SSID: "ZyXEL22518_Guest3" chanspec 0x2b06 selected Reaped 3860 UPnP daemon is ready to run

root@Zyxel:~# dmesg [ 0.000000] Linux version 5.15.134 (builder@buildhost) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23497-6637af95aa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Oct 9 21:45:35 2023 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-107.23 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board: board name: VH4032N [ 0.000000] MIPS: machine is Observa VH4032N [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s13200 r8192 d23664 u45056 [ 0.000000] pcpu-alloc: s13200 r8192 d23664 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 54572K/65536K available (7122K kernel code, 643K rwdata, 884K rodata, 1328K init, 221K bss, 10964K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns [ 0.000002] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns [ 0.008304] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656) [ 0.074701] pid_max: default: 32768 minimum: 301 [ 0.081696] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.089228] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.106005] rcu: Hierarchical SRCU implementation. [ 0.112517] smp: Bringing up secondary CPUs ... [ 0.119223] SMP: Booting CPU1... [ 4.010462] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 4.010499] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 4.010746] CPU1 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.182692] Synchronize counters for CPU 1: [ 0.203365] SMP: CPU1 is running [ 0.203379] done. [ 0.213282] smp: Brought up 1 node, 2 CPUs [ 0.229203] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.239390] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.246797] pinctrl core: initialized pinctrl subsystem [ 0.255638] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.262946] thermal_sys: Registered thermal governor 'step_wise' [ 0.269653] registering PCI controller with io_map_base unset [ 0.281714] registering PCI controller with io_map_base unset [ 0.312178] PCI host bridge to bus 0000:00 [ 0.316393] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.323525] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff] [ 0.330386] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.338749] pci 0000:00:01.0: [14e4:a8d6] type 00 class 0x028000 [ 0.346925] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00003fff] [ 0.361298] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.368159] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.375801] PCI host bridge to bus 0000:01 [ 0.380003] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff] [ 0.387040] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff] [ 0.393959] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.403344] pci 0000:01:1e.0: [14e4:6368] type 02 class 0x060700 [ 0.410091] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.418334] pci_bus 0000:02: extended config space not accessible [ 0.424763] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05 [ 0.431542] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05 [ 0.438401] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff] [ 0.445443] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff] [ 0.452275] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff] [ 0.459064] pci 0000:01:1e.0: CardBus bridge to [bus 02-05] [ 0.464812] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff] [ 0.471604] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff] [ 0.478428] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff] [ 0.486835] clocksource: Switched to clocksource MIPS [ 0.495091] b43-pci-bridge 0000:00:01.0: enabling device (0000 -> 0002) [ 0.567965] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.709018] b43-pci-bridge 0000:00:01.0: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.719360] NET: Registered PF_INET protocol family [ 0.724934] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.734545] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.743292] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.751270] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.759213] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.766519] TCP: Hash tables configured (established 1024 bind 1024) [ 0.773623] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.780498] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.788460] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.794381] PCI: CLS 0 bytes, default 16 [ 0.800948] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.820844] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.826939] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.840490] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.856645] gpio-507 (usb-hub-reset-gpio): hogged as output/high [ 0.863093] bcm6368-pinctrl 10000080.pin-controller: registered at mmio (ptrval) [ 0.873413] 10000100.serial: ttyS0 at MMIO 0x10000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart [ 0.883258] printk: console [ttyS0] enabled [ 0.891882] printk: bootconsole [early0] disabled [ 0.912247] bcm2835-rng bcm63xx-rng: hwrng registered [ 0.926009] random: crng init done [ 0.932337] physmap-flash 18000000.nor: physmap platform flash device: [mem 0x18000000-0x19ffffff] [ 0.941982] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.952545] 18000000.nor: Found an alias at 0x1000000 for the chip at 0x0 [ 0.952657] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.958021] Amd/Fujitsu Extended Query version 1.3. [ 0.963196] number of CFI chips: 1 [ 0.970346] Searching for RedBoot partition table in 18000000.nor at offset 0xfe0000 [ 1.012179] No RedBoot partition table detected in 18000000.nor [ 1.018516] 3 fixed-partitions partitions found on MTD device 18000000.nor [ 1.026055] Creating 3 MTD partitions on "18000000.nor": [ 1.031608] 0x000000000000-0x000000020000 : "CFE" [ 1.038916] 0x000000020000-0x000001fe0000 : "linux" [ 1.043959] mtd: partition "linux" extends beyond the end of device "18000000.nor" -- size truncated to 0xfe0000 [ 1.058604] parser_imagetag: rootfs: CFE image tag found at 0x0 with version 6, board type 96368VVW [ 1.068064] parser_imagetag: Partition 0 is kernel offset 100 and length 292d4c [ 1.075567] parser_imagetag: Partition 1 is rootfs offset 292e4c and length d4d1b4 [ 1.083411] parser_imagetag: Spare partition is offset 640004 and length 99fffc [ 1.091012] 2 bcm963xx-imagetag partitions found on MTD device linux [ 1.097577] Creating 2 MTD partitions on "linux": [ 1.102375] 0x000000000100-0x000000292e4c : "kernel" [ 1.107494] mtd: partition "kernel" doesn't start on an erase/write block boundary -- force read-only [ 1.119011] 0x000000292e4c-0x000000fe0000 : "rootfs" [ 1.124121] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.135611] mtd: setting mtd3 (rootfs) as root device [ 1.140930] 1 squashfs-split partitions found on MTD device rootfs [ 1.147333] 0x000000640000-0x000000fe0000 : "rootfs_data" [ 1.154810] 0x000001fe0000-0x000002000000 : "nvram" [ 1.159952] mtd: partition "nvram" is out of reach -- disabled [ 1.187862] bcm63xx-spi 10000800.spi: at [mem 0x10000800-0x10000f0b flags 0x200] (irq 9, FIFOs size 542) [ 1.199521] SPI driver b53-switch has no spi_device_id for brcm,bcm5325 [ 1.206349] SPI driver b53-switch has no spi_device_id for brcm,bcm53115 [ 1.213358] SPI driver b53-switch has no spi_device_id for brcm,bcm53125 [ 1.220346] SPI driver b53-switch has no spi_device_id for brcm,bcm53128 [ 1.227258] SPI driver b53-switch has no spi_device_id for brcm,bcm5365 [ 1.234035] SPI driver b53-switch has no spi_device_id for brcm,bcm5395 [ 1.240883] SPI driver b53-switch has no spi_device_id for brcm,bcm5397 [ 1.247712] SPI driver b53-switch has no spi_device_id for brcm,bcm5398 [ 1.322578] b53_common: found switch: BCM63xx, rev 0 [ 1.328823] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 1.341031] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.348333] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.355493] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.362710] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.369907] leds-gpio leds-gpio.0: Skipping unavailable LED gpio 0 ((null)) [ 1.381486] NET: Registered PF_INET6 protocol family [ 1.395597] Segment Routing with IPv6 [ 1.399534] In-situ OAM (IOAM) with IPv6 [ 1.403743] NET: Registered PF_PACKET protocol family [ 1.409073] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.422989] 8021q: 802.1Q VLAN Support v1.8 [ 1.457471] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.479619] Freeing unused kernel image (initmem) memory: 1328K [ 1.485679] This architecture does not have kernel memory protection. [ 1.492383] Run /sbin/init as init process [ 1.496537] with arguments: [ 1.496547] /sbin/init [ 1.496558] with environment: [ 1.496568] HOME=/ [ 1.496578] TERM=linux [ 2.350020] init: Console is alive [ 2.354204] init: - watchdog - [ 3.798403] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.903357] usbcore: registered new interface driver usbfs [ 3.909345] usbcore: registered new interface driver hub [ 3.915072] usbcore: registered new device driver usb [ 3.934133] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.943783] fsl-ehci: Freescale EHCI Host controller driver [ 3.952957] ehci-platform: EHCI generic platform driver [ 4.086928] ehci-platform ehci-platform: EHCI Host Controller [ 4.092854] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 4.101313] ehci-platform ehci-platform: irq 15, io mem 0xb0001500 [ 4.136829] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 4.146574] hub 1-0:1.0: USB hub found [ 4.150669] hub 1-0:1.0: 2 ports detected [ 4.167423] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.176156] ohci-platform: OHCI generic platform driver [ 4.181858] ohci-platform ohci-platform: Generic Platform OHCI controller [ 4.188934] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 4.197287] ohci-platform ohci-platform: irq 13, io mem 0xb0001600 [ 4.272275] hub 2-0:1.0: USB hub found [ 4.276319] hub 2-0:1.0: 2 ports detected [ 4.283434] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.301826] init: - preinit - [ 6.815983] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 6.823204] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on LAN1, 100Mbps, full-duplex [ 7.857230] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9.313182] jffs2: notice: (306) jffs2_build_xattr_subsystem: complete building xattr subsystem, 31 of xdatum (24 unchecked, 3 orphan) and 42 of xref (3 dead, 0 orphan) found. [ 9.332016] mount_root: switching to jffs2 overlay [ 9.356137] overlayfs: upper fs does not support tmpfile. [ 9.372907] urandom-seed: Seeding with /etc/urandom.seed [ 9.597354] procd: - early - [ 9.600794] procd: - watchdog - [ 10.392178] procd: - watchdog - [ 10.398980] procd: - ubus - [ 10.532657] procd: - init - [ 11.847298] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.592863] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b [ 12.600657] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36 [ 13.189904] PPP generic driver version 2.4.2 [ 13.200435] NET: Registered PF_PPPOX protocol family [ 13.252733] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 13.350895] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 13.357222] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Version 0 [ 13.392477] Broadcom 43xx driver loaded [ Features: PNL ] [ 13.457540] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.767066] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 15.087810] urngd: v1.0.2 started. [ 35.137385] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on LAN1, 100Mbps, full-duplex [ 35.155632] br-lan: port 1(eth0.1) entered blocking state [ 35.161338] br-lan: port 1(eth0.1) entered disabled state [ 35.167620] device eth0.1 entered promiscuous mode [ 35.172517] device eth0 entered promiscuous mode [ 35.191334] br-lan: port 1(eth0.1) entered blocking state [ 35.197004] br-lan: port 1(eth0.1) entered forwarding state [ 36.168617] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 40.796501] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07) [ 51.511486] phy0-sta0: authenticate with 82:2a:a8:81:8c:84 [ 51.547430] phy0-sta0: send auth to 82:2a:a8:81:8c:84 (try 1/3) [ 51.557725] phy0-sta0: authenticated [ 51.567058] phy0-sta0: associate with 82:2a:a8:81:8c:84 (try 1/3) [ 51.577614] phy0-sta0: RX AssocResp from 82:2a:a8:81:8c:84 (capab=0x431 status=0 aid=1) [ 51.607366] phy0-sta0: associated [ 52.158415] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-sta0: link becomes ready

CFE version 1.0.37-107.23 for BCM96368 (32bit,SP,BE) Build Date: 06/20/2011 (jhenyang@msgsw4) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name MX29GL128EH, id 0x2221 size 16384KB Total Flash size: 16384K with 128 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Checking Reset button on EXT INTR 0 Checking Reset button on EXT INTR 0 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Board Id (0-15) : 96368MVWG Number of MAC Addresses (1-32) : 7 Base MAC Address : 10:7b:ef:7a:00:00 PSI Size (1-128) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 33210 Wait for Multiboot Service Packet...  4 3 2 1 0 Booting from only image (0xb8020000) ... Code Address: 0x80A00000, Entry Address: 0x80a00000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80a00000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80a00000 [ 0.000000] Linux version 3.18.23 (kmottershead@kmottershead-i5) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48373) ) #1 Thu Feb 4 11:25:42 PST 2016 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-107.23 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board: board name: VSG1432 [ 0.000000] MIPS: machine is Zyxel VSG1432 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 59968K/65536K available (2670K kernel code, 139K rwdata, 564K rodata, 1288K init, 192K bss, 5568K reserved) [ 0.000000] NR_IRQS:256 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.052000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.068000] PCI host bridge to bus 0000:00 [ 0.072000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.076000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.080000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.088000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.092000] Switched to clocksource MIPS [ 0.096000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.124000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.168000] ssb: WARNING: Using fallback SPROM failed (err -2) [ 0.172000] ssb: WARNING: Invalid SPROM CRC (corrupt SPROM) [ 0.180000] ssb: Unsupported SPROM revision 255 detected. Will extract v1 [ 0.208000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.216000] NET: Registered protocol family 2 [ 0.224000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.228000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.236000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.244000] TCP: reno registered [ 0.248000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.252000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.260000] NET: Registered protocol family 1 [ 0.264000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.272000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.280000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.292000] msgmni has been set to 117 [ 0.296000] io scheduler noop registered [ 0.300000] io scheduler deadline registered (default) [ 0.308000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10, base_baud = 1562500) is a bcm63xx_uart [ 0.316000] console [ttyS0] enabled [ 0.316000] console [ttyS0] enabled [ 0.324000] bootconsole [early0] disabled [ 0.324000] bootconsole [early0] disabled [ 0.332000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.340000] 18000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.352000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.356000] Amd/Fujitsu Extended Query version 1.3. [ 0.360000] number of CFI chips: 1 [ 0.368000] bcm63xxpart: CFE boot tag found with version 6 and board type 9668MVWG [ 0.376000] 5 bcm63xxpart partitions found on MTD device 18000000.nor [ 0.380000] Creating 5 MTD partitions on "18000000.nor": [ 0.388000] 0x000000000000-0x000000020000 : "CFE" [ 0.392000] 0x000000020100-0x000000144b54 : "kernel" [ 0.400000] 0x000000144b54-0x000000fe0000 : "rootfs" [ 0.404000] mtd: device 2 (rootfs) set to be root filesystem [ 0.412000] 1 squashfs-split partitions found on MTD device rootfs [ 0.416000] 0x0000003c0000-0x000000fe0000 : "rootfs_data" [ 0.424000] 0x000000020000-0x000000fe0000 : "linux" [ 0.432000] 0x000000fe0000-0x000001000000 : "nvram" [ 0.440000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.488000] b53_common: found switch: BCM63xx, rev 0 [ 0.492000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.500000] TCP: cubic registered [ 0.504000] NET: Registered protocol family 17 [ 0.508000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.520000] 8021q: 802.1Q VLAN Support v1.8 [ 0.536000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.556000] Freeing unused kernel memory: 1288K (8035e000 - 804a0000) [ 1.844000] init: Console is alive [ 1.848000] init: - watchdog - [ 3.276000] usbcore: registered new interface driver usbfs [ 3.280000] usbcore: registered new interface driver hub [ 3.288000] usbcore: registered new device driver usb [ 3.300000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.312000] ehci-platform: EHCI generic platform driver [ 3.420000] ehci-platform ehci-platform: EHCI Host Controller [ 3.424000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 3.432000] ehci-platform ehci-platform: irq 15, io mem 0xb0001500 [ 3.452000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 3.460000] hub 1-0:1.0: USB hub found [ 3.464000] hub 1-0:1.0: 1 port detected [ 3.472000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.480000] ohci-platform: OHCI generic platform driver [ 3.488000] ohci-platform ohci-platform: Generic Platform OHCI controller [ 3.496000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 3.504000] ohci-platform ohci-platform: irq 13, io mem 0xb0001600 [ 3.568000] hub 2-0:1.0: USB hub found [ 3.572000] hub 2-0:1.0: 1 port detected [ 3.884000] init: - preinit - [ 4.524000] random: mktemp urandom read with 17 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.952000] jffs2: notice: (238) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 7.968000] mount_root: switching to jffs2 overlay ifconfig: SIOCGIFFLAGS: No such device [ 8.004000] procd: - early - [ 8.008000] procd: - watchdog - [ 8.904000] procd: - ubus - [ 9.920000] procd: - init - Please press Enter to activate this console. [ 11.204000] NET: Registered protocol family 10 [ 11.216000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.240000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 11.248000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 11.256000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.280000] nf_conntrack version 0.5.0 (957 buckets, 3828 max) [ 11.340000] xt_time: kernel timezone is -0000 [ 11.388000] cfg80211: Calling CRDA to update world regulatory domain [ 11.432000] cfg80211: World regulatory domain updated: [ 11.436000] cfg80211: DFS Master region: unset [ 11.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.448000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.460000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 11.468000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.476000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 11.484000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 11.496000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.504000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.512000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.604000] PPP generic driver version 2.4.2 [ 11.612000] NET: Registered protocol family 24 [ 11.656000] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 11.696000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 11.700000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 6, Version 0 [ 11.720000] Broadcom 43xx driver loaded [ Features: PNL ] [ 21.976000] device eth0.1 entered promiscuous mode [ 21.980000] device eth0 entered promiscuous mode [ 21.996000] br-lan: port 1(eth0.1) entered forwarding state [ 22.000000] br-lan: port 1(eth0.1) entered forwarding state [ 24.004000] br-lan: port 1(eth0.1) entered forwarding state [ 32.916000] random: nonblocking pool is initialized BusyBox v1.23.2 (2016-02-04 11:21:17 PST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CMER (Chaos Calmer, r48373) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:/#