Show pagesourceOld revisionsBacklinksBack to top × Table of Contents ZyXEL WAP3205 Supported Versions Hardware Highlights Installation Hardware Info Opening the case Serial JTAG Bootloader Tags ZyXEL WAP3205 Supported Versions BrandModel↓ VersionCurrent ReleaseOEM InfoForum TopicTechnical DataZyXELWAP3205v119.07.10View/Edit dataZyXELWAP3205v222.03.3http://www.zyxel.com/products_services/wap3205_v2.shtml?t=phttps://forum.openwrt.org/viewtopic.php?id=52664View/Edit data Hardware Highlights Model↓ VersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBWAP3205v1Ralink RT3052384432Ralink RT3052b/g/n-2---WAP3205v2Ralink RT3352384864Ralink RT3352b/g/n-2--- Installation Model↓ VersionCurrent ReleaseFirmware OpenWrt InstallFirmware OpenWrt UpgradeFirmware OEM StockWAP3205v119.07.10https://downloads.openwrt.org/releases/19.07.10/targets/ramips/rt305x/openwrt-19.07.10-ramips-rt305x-nbg-419n-initramfs-kernel.binhttps://downloads.openwrt.org/releases/19.07.10/targets/ramips/rt305x/openwrt-19.07.10-ramips-rt305x-nbg-419n-squashfs-sysupgrade.binWAP3205v222.03.3https://downloads.openwrt.org/releases/22.03.3/targets/ramips/rt305x/openwrt-22.03.3-ramips-rt305x-zyxel_nbg-419n-v2-squashfs-sysupgrade.bin → Install OpenWrt (generic explanation) The board is the same one used on the ZyXEL NBG-419N, but has 2 Ethernet ports instead of 4 LAN + 1 WAN. (and has no WiFi on/off switch) Support for the ZyXEL NBG-419N appeared in r28078, so you can download an Attitude Adjustment (12.09 final) openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin image or you can build from the source. See toolchain. Select Ralink RT288x/RT305x as Target System and RT305x based boards as Subtarget in make menuconfig. You should obtain <buildroot dir>/bin/ramips/openwrt-ramips-rt305x-nbg-419n-squashfs-sysupgrade.bin. The only issue is that the Switch/VLAN configurations let you configure even the ports that are actually unpopulated on the PCB, and obviously LuCI will show the wrong model on the webadmin. The rest of the installation process is the same as the ZyXEL NBG-419N. Hardware Info Architecture MIPS Vendor Ralink Bootloader U-Boot System-On-Chip Ralink RT3052 CPU Speed 384 MHz Flash size 4 MiB RAM 32 MiB USB No (Not populated) Serial Yes JTAG Yes Opening the case Note: This will void your warranty! To remove the cover simply remove the two screws on the bottom. Then just open it. The board itself has no screws. Serial The are 4 pins on the board marked as follows: RX GND TX 3V3 JTAG → port.jtag general information about the JTAG port, JTAG cable, etc. How to connect to the JTAG Port of this specific device: Insert photo of PCB with markings for JTAG port Bootloader The bootloader used in this unit is U-Boot. It is available through the serial interface with the settings: 57600/N/1 Tags How to add tags ramips, rt3052, 4Flash, 32RAM This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies ramips rt3052 4Flash 32RAM Last modified: 2021/10/15 05:06by bobafetthotmail