YunCore AX835

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

AX835 is a high-performance, high-speed 11ax indoor dual-band ceiling AP that can provide 2.4G (40MHz channel width) and 5.8GHz (160 MHz) dual-band wireless services. 2.4G provides up to 574Mbps access rate, and 5G provides up to 2402Mbps access rate. Supports two power supply modes: 48V PoE and DC 12V. Manufactured in two different form factors (square and round). Available 2023 on Aliexpress under the KuWfi brand as “KuWFi 3000Mbps Ceiling AP” (Model: AX835).

YuncoreAX835 YuncoreAX835

None at this time.

Option 1:

  1. Connect to the router using an ethernet cable
  2. Spin up a TFTP server serving the install/kernel file above
  3. Open the case and attach an UART
  4. Attach power to the router and interrupt the countdown by pressing any key
  5. Boot kernel image via TFTP
  6. Backup stock image using your preferred method, download backups
  7. Flash the upgrade image using your preferred method

Option 2:

  1. Connect to the router using an ethernet cable
  2. Spin up a TFTP server serving the upgrade image above
  3. Open the case and attach an UART
  4. Attach power to the router and interrupt the countdown by pressing any key
  5. Select option 2 (Upgrade firmware)
  6. Enter IP address information and image name
  7. Wait patiently
dev:    size   erasesize  name
mtd0: 00040000 00010000 "BL2"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "Factory"
mtd3: 00080000 00010000 "FIP"
mtd4: 00e00000 00010000 "firmware"
mtd5: 00350000 00010000 "kernel"
mtd6: 00aa0000 00010000 "rootfs"
mtd7: 000e0000 00010000 "rootfs_data"
  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Dumb AP configuration In most cases, you'll need to configure a “Dumb AP”.

Since the device uses DSA, only the wan and lan interfaces should be used.

Port Switch port
1Gbps LAN 3
1Gbps WAN (with 802.3af PoE) 4
2.5Gbps CPU port (internal) 6

hardware.button on howto use and configure the hardware button(s).

The YunCore AX835 has the following buttons:

BUTTON Event
Reset reset

→ How to configure LEDs in general, see the LED section in the led_configuration.

Yuncore AX835 has 3 LEDs:

LED name Internal name
Front RGB - red red:system
Front RGB - blue blue:wifi5
Front RGB - green green:wifi2

Front:

Back:

Backside label:

Note: This will void your warranty!

To remove the cover, remove four Phillips screws.

Main PCB:

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial pinout (115200, 8N1, 3.3V)

o o o []
1 2 3 4

1 - GND
2 - RX
3 - TX
4 - VCC

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.230 (gqq@gq) (gcc version 8.4.0 (OpenWrt GCC 8. 4.0 r16823-4292832a6a)) #0 SMP Sat Jan 28 18:26:47 2023 [ 0.000000] Machine model: MediaTek MT7981 RFB [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] On node 0 totalpages: 64592 [ 0.000000] DMA32 zone: 1024 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 64592 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920 [ 0.000000] pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel conf iguration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 63568 [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, l inear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 230668K/258368K available (6910K kernel code, 446K rwdata , 1968K rodata, 448K init, 286K bss, 27700K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jif fies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000003] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 43980 46511101ns [ 0.008176] Calibrating delay loop (skipped), value calculated using timer fr equency.. 26.00 BogoMIPS (lpj=52000) [ 0.018496] pid_max: default: 32768 minimum: 301 [ 0.023209] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear ) [ 0.030469] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, l inear) [ 0.039033] ASID allocator initialised with 65536 entries [ 0.044535] rcu: Hierarchical SRCU implementation. [ 0.049625] smp: Bringing up secondary CPUs ... [ 0.054490] Detected VIPT I-cache on CPU1 [ 0.054510] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.054531] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.054587] smp: Brought up 1 node, 2 CPUs [ 0.076199] SMP: Total of 2 processors activated. [ 0.080925] CPU features: detected: 32-bit EL0 Support [ 0.086087] CPU features: detected: CRC32 instructions [ 0.091355] CPU: All CPU(s) started at EL2 [ 0.095477] alternatives: patching kernel code [ 0.102103] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 7645041785100000 ns [ 0.111912] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.118808] pinctrl core: initialized pinctrl subsystem [ 0.124677] NET: Registered protocol family 16 [ 0.129357] DMA: preallocated 256 KiB pool for atomic allocations [ 0.150898] SCSI subsystem initialized [ 0.154834] libata version 3.00 loaded. [ 0.158926] usbcore: registered new interface driver usbfs [ 0.164499] usbcore: registered new interface driver hub [ 0.169877] usbcore: registered new device driver usb [ 0.175710] Bluetooth: Core ver 2.22 [ 0.179353] NET: Registered protocol family 31 [ 0.183824] Bluetooth: HCI device and connection manager initialized [ 0.190215] Bluetooth: HCI socket layer initialized [ 0.195117] Bluetooth: L2CAP socket layer initialized [ 0.200199] Bluetooth: SCO socket layer initialized [ 0.205314] rbus 18000000.wbsys: PCI host bridge to bus 0000:00 [ 0.211273] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff] [ 0.218185] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.223697] pci_bus 0000:00: scanning bus [ 0.227736] pci 0000:00:00.0: [14c3:7981] type 00 class 0x000280 [ 0.233782] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit] [ 0.240606] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f] [ 0.246905] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f] [ 0.253205] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f] [ 0.259504] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f] [ 0.266493] pci_bus 0000:00: fixups for bus [ 0.270707] pci_bus 0000:00: bus scan returning with max=00 [ 0.277071] clocksource: Switched to clocksource arch_sys_counter [ 0.283830] thermal_sys: Registered thermal governor 'fair_share' [ 0.283833] thermal_sys: Registered thermal governor 'bang_bang' [ 0.289977] thermal_sys: Registered thermal governor 'step_wise' [ 0.296015] thermal_sys: Registered thermal governor 'user_space' [ 0.302050] thermal_sys: Registered thermal governor 'power_allocator' [ 0.308401] NET: Registered protocol family 2 [ 0.319431] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear ) [ 0.326960] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.335374] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.343172] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.350366] TCP: Hash tables configured (established 2048 bind 2048) [ 0.356808] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.363380] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.370475] NET: Registered protocol family 1 [ 0.374876] PCI: CLS 0 bytes, default 64 [ 0.379548] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.388810] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.394689] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 0.417351] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0 [ 0.434031] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.441136] printk: console [ttyS0] disabled [ 0.465543] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2 [ 0.474752] printk: console [ttyS0] enabled [ 0.483116] printk: bootconsole [uart8250] disabled [ 0.493421] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.501724] loop: module loaded [ 0.504972] mediatek,mt2701-ice_debug ice_debug: get dbg_sel clock fail: -2 [ 0.511945] mediatek,mt2701-ice_debug: probe of ice_debug failed with error - 2 [ 0.519971] mt7981-pinctrl 11d00000.pinctrl: pin_config_set op failed for pin 29 [ 0.527371] mtk-spi 11009000.spi: Error applying setting, reverse things back [ 0.535133] spi-nor spi0.0: calibration result: 0x2 [ 0.549239] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.554276] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.560660] Creating 5 MTD partitions on "spi0.0": [ 0.565451] 0x000000000000-0x000000040000 : "BL2" [ 0.570667] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.576439] 0x000000050000-0x000000100000 : "Factory" [ 0.581941] 0x000000100000-0x000000180000 : "FIP" [ 0.587096] 0x000000180000-0x000000f80000 : "firmware" [ 0.592803] 2 fit-fw partitions found on MTD device firmware [ 0.598480] 0x000000180000-0x0000004c0000 : "kernel" [ 0.603944] 0x0000004c0000-0x000000f80000 : "rootfs" [ 0.609397] mtd: device 6 (rootfs) set to be root filesystem [ 0.615106] 1 squashfs-split partitions found on MTD device rootfs [ 0.621300] 0x000000dd0000-0x000000f80000 : "rootfs_data" [ 0.628268] [mtk_hw_init] reset_lock:0, force:0 [ 0.632829] [mtk_hw_init] execute fe cold reset [ 0.648481] mtk_soc_eth 15100000.ethernet: MDC is running on 2500000 Hz [ 0.695692] MediaTek MT7981 PHY mdio-bus:00: TX-VCM SW cal result: 0x3 [ 0.703470] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xff ffffc011900000, irq 75 [ 0.712522] (unnamed net_device) (dummy): netif_napi_add() called with weight 256 [ 0.720319] xhci-mtk 11200000.xhci: 11200000.xhci supply vbus not found, usin g dummy regulator [ 0.728984] xhci-mtk 11200000.xhci: 11200000.xhci supply vusb33 not found, us ing dummy regulator [ 0.737874] phy phy-usb-phy@11e10000.0: try to get sw efuse [ 0.743530] xhci-mtk 11200000.xhci: xHCI Host Controller [ 0.748873] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus numb er 1 [ 0.756423] xhci-mtk 11200000.xhci: hcc params 0x01403f99 hci version 0x110 q uirks 0x0000000000210010 [ 0.765665] xhci-mtk 11200000.xhci: irq 84, io mem 0x11200000 [ 0.771841] hub 1-0:1.0: USB hub found [ 0.775628] hub 1-0:1.0: 1 port detected [ 0.779787] xhci-mtk 11200000.xhci: xHCI Host Controller [ 0.785110] xhci-mtk 11200000.xhci: new USB bus registered, assigned bus numb er 2 [ 0.792592] xhci-mtk 11200000.xhci: Host supports USB 3.2 Enhanced SuperSpeed [ 0.799769] usb usb2: We don't know the algorithms for LPM for this host, dis abling LPM. [ 0.808173] hub 2-0:1.0: USB hub found [ 0.811963] hub 2-0:1.0: 1 port detected [ 0.816361] usbcore: registered new interface driver uas [ 0.821752] usbcore: registered new interface driver usb-storage [ 0.827875] i2c /dev entries driver [ 0.832241] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowa yout=0) [ 0.840225] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-d evel@redhat.com [ 0.848791] Bluetooth: HCI UART driver ver 2.3 [ 0.853255] Bluetooth: HCI UART protocol H4 registered [ 0.858386] Bluetooth: HCI UART protocol BCSP registered [ 0.863776] Bluetooth: HCI UART protocol Broadcom registered [ 0.869452] Bluetooth: HCI UART protocol QCA registered [ 0.876720] NET: Registered protocol family 10 [ 0.881844] Segment Routing with IPv6 [ 0.885580] NET: Registered protocol family 17 [ 0.890082] Bridge firewalling registered [ 0.894217] 8021q: 802.1Q VLAN Support v1.8 [ 1.477108] mt753x gsw@0: LAN/WAN VLAN setting=llllw [ 1.482342] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1 [ 1.492102] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz [ 3.136591] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: [ 3.144569] mt753x gsw@0: -------- gephy-calbration (port:0) -------- [ 3.159773] CALDLY = 40 [ 3.227346] 0x1e-e0 = 2b2b [ 3.231748] 0x1f-115 = 5 [ 3.234273] GE Rext AnaCal Done! (11)(0x2b) M [ 3.307547] GE R50 AnaCal Done! (12) (0x30)(0xb0) M [ 3.376228] GE R50 AnaCal Done! (12) (0x30)(0xb0) M [ 3.449465] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 3.531810] GE R50 AnaCal Done! (15) (0x23)(0xa3) M [ 3.539661] GE 1e_174(0xb0b0), 1e_175(0xa6a3) M [ 3.586043] GE Tx offset AnaCal Done! (pair-0)(4)(0x23) 0x1e_172=0x2320 [ 3.615465] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2322 [ 3.654000] GE Tx offset AnaCal Done! (pair-2)(5)(0x24) 0x1e_173=0x2420 [ 3.697091] GE Tx offset AnaCal Done! (pair-3)(6)(0x25) 0x1e_173=0x2425 [ 3.804533] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x7c1f) [ 3.903594] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2424) [ 3.994777] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x222a) [ 4.057649] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1e26) [ 4.104357] PORT 0 RX_DC_OFFSET [ 4.117025] before pairA output = 1e [ 4.122377] after pairA output = 1 [ 4.127473] before pairB output = f [ 4.132736] after pairB output = 0 [ 4.137831] before pairC output = e [ 4.143094] after pairC output = 1 [ 4.148191] before pairD output = 1e [ 4.153542] after pairD output = 1 [ 4.157187] mt753x gsw@0: -------- gephy-calbration (port:1) -------- [ 4.172390] CALDLY = 40 [ 4.266396] GE R50 AnaCal Done! (18) (0x20)(0xa0) M [ 4.357855] GE R50 AnaCal Done! (17) (0x21)(0xa1) M [ 4.444756] GE R50 AnaCal Done! (16) (0x22)(0xa2) M [ 4.531659] GE R50 AnaCal Done! (16) (0x22)(0xa2) M [ 4.539509] GE 1e_174(0xa0a1), 1e_175(0xa2a2) M [ 4.581336] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 4.606204] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2221 [ 4.631071] GE Tx offset AnaCal Done! (pair-2)(2)(0x2) 0x1e_173=0x220 [ 4.660319] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x203 [ 4.744935] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x701c) [ 4.832674] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2323) [ 4.940844] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x262e) [ 5.015042] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x2028) [ 5.061751] PORT 1 RX_DC_OFFSET [ 5.074414] before pairA output = f [ 5.079677] after pairA output = ff [ 5.084862] before pairB output = 1e [ 5.090212] after pairB output = fe [ 5.095395] before pairC output = f [ 5.100658] after pairC output = fe [ 5.105841] before pairD output = 1e [ 5.111190] after pairD output = 1 [ 5.114841] mt753x gsw@0: -------- gephy-calbration (port:2) -------- [ 5.130043] CALDLY = 40 [ 5.201268] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 5.274502] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 5.347735] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 5.420976] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 5.428827] GE 1e_174(0xa6a6), 1e_175(0xa6a6) M [ 5.479760] GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420 [ 5.504630] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2421 [ 5.524944] GE Tx offset AnaCal Done! (pair-2)(1)(0x1) 0x1e_173=0x120 [ 5.567859] GE Tx offset AnaCal Done! (pair-3)(6)(0x25) 0x1e_173=0x125 [ 5.658227] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x781e) [ 5.711991] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c) [ 5.820163] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x272f) [ 5.900020] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x2129) [ 5.946726] PORT 2 RX_DC_OFFSET [ 5.959393] before pairA output = e [ 5.964656] after pairA output = ff [ 5.969839] before pairB output = 1d [ 5.975188] after pairB output = ff [ 5.980370] before pairC output = 1e [ 5.985719] after pairC output = ff [ 5.990903] before pairD output = f [ 5.996166] after pairD output = ff [ 5.999903] mt753x gsw@0: -------- gephy-calbration (port:3) -------- [ 6.015107] CALDLY = 40 [ 6.095449] GE R50 AnaCal Done! (15) (0x23)(0xa3) M [ 6.168687] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 6.241926] GE R50 AnaCal Done! (13) (0x26)(0xa6) M [ 6.310610] GE R50 AnaCal Done! (12) (0x30)(0xb0) M [ 6.318461] GE 1e_174(0xa3a6), 1e_175(0xa6b0) M [ 6.360285] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 6.389708] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2222 [ 6.414580] GE Tx offset AnaCal Done! (pair-2)(2)(0x2) 0x1e_173=0x220 [ 6.443831] GE Tx offset AnaCal Done! (pair-3)(3)(0x22) 0x1e_173=0x222 [ 6.522870] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5014) [ 6.627594] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2626) [ 6.701792] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2129) [ 6.781649] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x222a) [ 6.828359] PORT 3 RX_DC_OFFSET [ 6.841026] before pairA output = 1e [ 6.846377] after pairA output = 1 [ 6.851473] before pairB output = f [ 6.856736] after pairB output = 0 [ 6.861832] before pairC output = e [ 6.867096] after pairC output = 1 [ 6.872192] before pairD output = 1e [ 6.877542] after pairD output = fe [ 6.881274] mt753x gsw@0: -------- gephy-calbration (port:4) -------- [ 6.896477] CALDLY = 40 [ 6.963152] GE R50 AnaCal Done! (12) (0x30)(0xb0) M [ 7.027277] GE R50 AnaCal Done! (11) (0x31)(0xb1) M [ 7.086851] GE R50 AnaCal Done! (10) (0x32)(0xb2) M [ 7.155532] GE R50 AnaCal Done! (12) (0x30)(0xb0) M [ 7.163382] GE 1e_174(0xb0b1), 1e_175(0xb2b0) M [ 7.200650] GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120 [ 7.230073] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2122 [ 7.268603] GE Tx offset AnaCal Done! (pair-2)(5)(0x24) 0x1e_173=0x2420 [ 7.293474] GE Tx offset AnaCal Done! (pair-3)(2)(0x21) 0x1e_173=0x2421 [ 7.400906] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x3c0f) [ 7.482984] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0xd0d) [ 7.540111] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x121a) [ 7.591656] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x131b) [ 7.638369] PORT 4 RX_DC_OFFSET [ 7.651037] before pairA output = e [ 7.656299] after pairA output = 0 [ 7.661395] before pairB output = 1e [ 7.666739] after pairB output = fe [ 7.671923] before pairC output = 1e [ 7.677272] after pairC output = ff [ 7.682451] before pairD output = d [ 7.687716] after pairD output = 1 [ 7.695947] hctosys: unable to open rtc device (rtc0) [ 7.703611] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 7.710897] Freeing unused kernel memory: 448K [ 7.721110] Run /sbin/init as init process [ 7.955016] init: Console is alive [ 7.958554] init: - watchdog - [ 8.569350] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.603388] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_reg ister [ 8.611074] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xfffff fc010afd000) size=(0x1000) [ 8.620462] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc 010b05000) size=(0x1000) [ 8.629671] Get Index(2-GPIO_BASE) phy_addr(0x11d00000) vir_addr=(0xffffffc01 0b0d000) size=(0x1000) [ 8.638705] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xfffff fc010b15000) size=(0x1000) [ 8.648087] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xfffff fc010b17000) size=(0x1000) [ 8.657481] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xff ffffc010b19000) size=(0x1000) [ 8.667129] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0 xffffffc010b1b000) size=(0x1000) [ 8.677192] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr =(0xffffffc010b1d000) size=(0x1000) [ 8.687367] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) v ir_addr=(0xffffffc010b1f000) size=(0x1000) [ 8.698301] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr =(0xffffffc010b21000) size=(0x1000) [ 8.708463] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_add r=(0xffffffc010b23000) size=(0x1000) [ 8.718712] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=( 0xffffffc010b25000) size=(0x1000) [ 8.728700] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_a ddr=(0xffffffc010b2d000) size=(0x1000) [ 8.739122] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010b2f000) size=(0x1000) [ 8.750073] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_a ddr=(0xffffffc010b31000) size=(0x1000) [ 8.760663] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010b33000) size=(0x1000) [ 8.771607] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=( 0xffffffc010bb0000) size=(0x10000) [ 8.781682] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0x ffffffc010ba1000) size=(0x1000) [ 8.791498] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr =(0xffffffc010ba3000) size=(0x1000) [ 8.801661] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_add r=(0xffffffc010be0000) size=(0x10000) [ 8.811996] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xff ffffc010ba5000) size=(0x1000) [ 8.821637] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr =(0xffffffc010ba7000) size=(0x1000) [ 8.831799] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0 xffffffc010ba9000) size=(0x1000) [ 8.841700] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_a ddr(0x18500000) vir_addr=(0xffffffc010bab000) size=(0x1000) [ 8.853944] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0 xffffffc010e10000) size=(0x10000) [ 8.863931] conninfra@(consys_plt_hw_init:162) adie_cfg_type = 1, one_adie_db dc = 1 [ 8.871580] [emi_mng_init] gConEmiPhyBase = [0x47c80000] size = [0x100000] fw size = [0x100000] ops=[(____ptrval____)] [ 8.882354] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_regi ster [ 8.890229] ConnInfra Dev: init (0) [ 8.895164] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP ver sion successfully! (0x02090000) [ 8.905002] conninfra@(connsys_d_die_cfg:365) D-die efuse: 0x00000000 [ 8.912477] conninfra@(_connsys_a_die_cfg_7976:919) adie_idx[0], A-die CHIP I D = 0x7976, HW Version = 0x8a10 [ 8.923299] conninfra@(consys_spi_write_nolock:501) addr=0x0a00, val=0xffffff ff [ 8.931602] conninfra@(consys_spi_write_nolock:501) addr=0x04ac, val=0x000000 1c [ 8.939906] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x000000 02 [ 8.949216] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x000000 00 [ 8.958526] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x43a600 00 [ 8.971866] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x000000 01, 0x00c40000, 0x008900b3, 0x00000000] [ 8.983378] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x000000 02 [ 8.992689] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a600 3a [ 9.001999] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63a700 3a [ 9.015341] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x000000 01, 0x00c40000, 0x008900b3, 0x00000000] [ 9.026853] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x000000 02 [ 9.036164] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a700 3a [ 9.045473] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63ac00 3a [ 9.058814] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x000000 01, 0x00c40000, 0x008900b3, 0x00000000] [ 9.070327] conninfra@(consys_spi_write_nolock:501) addr=0x0038, val=0x4a563b 00 [ 9.078630] conninfra@(consys_spi_write_nolock:501) addr=0x065c, val=0x1d5908 0f [ 9.086933] conninfra@(consys_spi_write_nolock:501) addr=0x0664, val=0x34c00f e0 [ 9.095238] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x888880 05 [ 9.104498] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x000000 05 [ 9.112735] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP ver sion successfully! (0x02090000) [ 9.122548] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refc nt=[0]->[1] wakeup!! [ 9.131413] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt =[1]->[0] sleep!! [ 9.140013] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0 ] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1] [ 9.152439] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.159571] fsl-ehci: Freescale EHCI Host controller driver [ 9.165748] ehci-platform: EHCI generic platform driver [ 9.172410] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 9.179130] ohci-platform: OHCI generic platform driver [ 9.187790] mediatek_soc_hnat 15100000.hnat: wan = eth0.2 [ 9.193216] mediatek_soc_hnat 15100000.hnat: lan = eth0.1 [ 9.198625] mediatek_soc_hnat 15100000.hnat: lan2 = eth2 [ 9.203931] mediatek_soc_hnat 15100000.hnat: ppd = eth0 [ 9.209148] mediatek_soc_hnat 15100000.hnat: gmac num = 1 [ 9.214542] mediatek_soc_hnat 15100000.hnat: ppe num = 1 [ 9.220256] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192 [ 9.237019] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start [ 9.242814] hnat roaming work enable [ 9.249422] warp_module_init(): module init and register callback for warp [ 9.256319] create warp_ctrl ok!!! [ 9.259758] wed_get_slot_map(): assign slot_id:0 for entry: 0! [ 9.265599] wed_get_slot_map(): assign slot_id:1 for entry: 1! [ 9.271907] kmodloader: done loading kernel modules from /etc/modules-boot.d/ * [ 9.287719] init: - preinit - [ 9.550921] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500bas e-x link mode [ 9.559248] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - f low control rx/tx [ 11.626366] mount_root: loading kmods from internal overlay [ 11.639320] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 11.646730] kmodloader: done loading kernel modules from //etc/modules-boot.d /* [ 11.960606] jffs2: notice: (869) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 44 of xdatum (20 unchecked, 24 orphan) and 53 of xref (10 de ad, 18 orphan) found. [ 11.976898] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 11.987440] block: extroot: not configured [ 12.015163] jffs2: notice: (867) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 44 of xdatum (20 unchecked, 24 orphan) and 53 of xref (10 de ad, 18 orphan) found. [ 12.032109] mount_root: loading kmods from internal overlay [ 12.046285] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/mo dules-boot.d/* [ 12.055865] kmodloader: done loading kernel modules from /tmp/overlay/upper/e tc/modules-boot.d/* [ 12.268672] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 12.278032] block: extroot: not configured [ 12.282891] mount_root: switching to jffs2 overlay [ 12.290066] overlayfs: upper fs does not support tmpfile. [ 12.296076] overlayfs: "xino" feature enabled using 32 upper inode bits. [ 12.304394] urandom-seed: Seeding with /etc/urandom.seed [ 12.413576] procd: - early - [ 12.416481] procd: - watchdog - [ 12.950683] procd: - watchdog - [ 12.967565] procd: - ubus - [ 13.029298] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.036117] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.042631] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.049773] procd: - init - [ 13.279979] urngd: v1.0.2 started. [ 13.295310] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.308099] random: crng init done [ 13.311531] random: 20 urandom warning(s) missed due to ratelimiting [ 13.334684] RPC: Registered named UNIX socket transport module. [ 13.340695] RPC: Registered udp transport module. [ 13.345400] RPC: Registered tcp transport module. [ 13.350095] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 13.365523] l2tp_core: L2TP core driver, V2.0 [ 13.370471] l2tp_netlink: L2TP netlink interface [ 13.375745] gre: GRE over IPv4 demultiplexor driver [ 13.381396] ip_gre: GRE over IPv4 tunneling driver [ 13.391479] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 14.386481] mt_wifi: module license 'Proprietary' taints kernel. [ 14.392496] Disabling lock debugging due to kernel taint [ 14.430303] conninfra@(conninfra_pwr_on:120) [conninfra_pwr_on] drv=[3] [ 14.437961] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP ver sion successfully! (0x02090000) [ 14.455824] [[1;32mAdie Type: 0x7976[[0m [ 14.455827] [[1;32mSKU Type: 3000[[0m [ 14.459780] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0 ] FM=[0] GPS=[0] WF=[1] CONNINFRA=[1] [ 14.473893] WiFi@C12L1,get_dbg_setting_by_profile() 4373: debug level setting =INDEX0_debug_level not found!! [ 14.483766] WiFi@C12L1,get_dbg_setting_by_profile() 4396: debug option settin g=INDEX0_debug_option not found!! [ 14.493833] mt_rbus 0000:00:00.0: runtime IRQ mapping not provided by arch [ 14.507651] mt7981_init()--> [ 14.510591] Use the default iPAiLNA bin image! [ 14.515757] <--mt7981_init() [ 14.518723] RtmpRaDevCtrlInit(): MCS_LUT not used becasue MacTb size(288) > 1 28! [ 14.526662] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X1 [ 14.534011] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X2 [ 14.541345] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X3 [ 14.548699] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X4 [ 14.556045] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X5 [ 14.563387] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X6 [ 14.570723] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X7 [ 14.578055] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X8 [ 14.585392] WiFi@C12L1,match_index_by_chipname() 566: not find chip name INDE X9 [ 14.592712] WiFi@C12L2,match_index_by_chipname() 571: Not find slot id, back to old rule. [ 14.601022] msta_ifname not found [ 14.612597] -->mtfwd_init(ver:2.0) [ 14.612642] <-- [ 14.616805] mtk_warp_proxy: module uses symbols from proprietary module mt_wi fi, inheriting taint. [ 14.628997] -->mtqos_init(), mtqos ver:1.0 [ 14.629039] <-- [ 14.646922] xt_time: kernel timezone is -0000 [ 14.674426] PPP generic driver version 2.4.2 [ 14.680176] PPP MPPE Compression module registered [ 14.686047] NET: Registered protocol family 24 [ 14.691476] PPTP driver version 0.8.5 [ 14.703388] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 14.710464] kmodloader: done loading kernel modules from /etc/modules.d/* [ 18.824759] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 18.899106] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500bas e-x link mode [ 18.907444] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - f low control rx/tx .. [ 19.296143] pctools start 18:27:58 up 0 min, load average: 0.21, 0.04, 0.01 [ 19.884946] 7981@C01L2,RTMP_COM_IoctlHandle() 1514: -> CMD_RTPRIV_IOCTL_VIRTU AL_INF_INIT [ 19.897874] msta_ifname not found [ 19.901999] client_get_axi_slot_id(): wrong BUS_TYPE [ 19.907027] warp_cap_support(): chip_id=7981 is in WHNAT support list [ 19.913487] warp_entry_acquire(): bus slot:0, hook to WARP, entry id=0, entry : 00000000f3895f13 [ 19.922198] client_hif_specific_get(): hw->base_phy_addr 0x18000000!! [ 19.928666] client_chip_specific_get(): 0x7981 chip id 0x7981!! [ 19.934694] warp_entry_get_by_pdev(): return entry[0] [ 19.940004] warp_msg_register():warp,pid,3274,id,0,wed_idx,0 [ 19.945730] warp_dev0 15010000.wed: Using 32bit DMA for streaming map [ 19.952205] warp_dev0 15010000.wed: Using 32bit DMA for coherent map [ 19.958619] wed_init(0): res_start = 0x15010000, size = 1000, irq=7,base_addr =0xffffffc0111e5000 [ 19.968042] wed_ring_init(): wed tx ring init result = 0 [ 19.973952] wed_ring_init(): wed rx ring init result = 0 [ 19.981435] GetEntryFromFreeList: allocated new pool [ 19.988482] create wed ok!!! [ 19.991454] wdma_init(): wdma(0) base_addr=0xffffffc0111ed800, base_phy_addr= 0x15104800 [ 20.000280] warp_woif_bus_init_hw(): bus:00000000aecdcf97, txring: 20, pa: 0x 00000000476ca000, 0x00000000476ca000, 24, 28, 3c [ 20.011612] warp_woif_bus_init_hw(): bus:00000000aecdcf97, rxring: 50, pa: 0x 000000004760c000, 0x000000004760c000, 54, 58, 6c [ 20.022977] get_region_info(): wed_idx = 0, base_addr = 0x0000000019d92935, s ize = 0x40000, res.start = 0x47d80000, shared:0 [ 20.034225] get_region_info(): wed_idx = 0, base_addr = 0x00000000868925fa, s ize = 0x8000, res.start = 0x151e0000, shared:0 [ 20.045425] get_region_info(): wed_idx = 0, base_addr = 0x0000000059fb6906, s ize = 0x240000, res.start = 0x47dc0000, shared:1 [ 20.056780] get_region_info(): wed_idx = 0, base_addr = 0x00000000a82703c4, s ize = 0x1000, res.start = 0x15194000, shared:0 [ 20.067922] warp_fwdl_mcu_mode(): mcu mode, need fwdl [ 20.119489] ########## WO Firmware ########## [ 20.123887] Chip ID: 0x0000 [ 20.126705] ECO version:0 [ 20.129339] Version: DEV_000000 [ 20.132473] Build date: 20221208202138 [ 20.136235] Total region:3 [ 20.138946] ################################# [ 20.143313] Parsing tailer region 0 [ 20.146826] Target address: 0x151e0000 [ 20.150677] Download size: 20768 [ 20.154031] Parsing tailer region 1 [ 20.157524] Target address: 0x47d80000 [ 20.161362] Download size: 86816 [ 20.164736] Parsing tailer region 2 [ 20.168244] Target address: 0x47dc0000 [ 20.172094] Download size: 2319824 [ 20.178321] warp_fwdl_ready_check_mcu_mode(): waiting for wocpu [ 20.198665] warp_fwdl_ready_check_mcu_mode(): wocpu is ready [ 20.204624] warp_woctrl_init_state(), wo_state: WO_STATE_ENABLE [ 20.210599] wo_proc_init done 00000000f5116d95 [ 20.215150] wo_exep_proc_init done 00000000f5116d95 [ 20.220162] wo_exception_init(0): exp log= 0x000000000383fd7a, phy_addr= 0x00 000000469d8000 size= 32768 [ 20.234641] 7981@C00L1,hc_init_ChCtrl() 2161: Clear ChCtrl Band[0] (caller:Us erCfgInit+0x5fc/0x1320 [mt_wifi]) [ 20.244858] 7981@C00L1,hc_init_ChCtrl() 2161: Clear ChCtrl Band[1] (caller:Us erCfgInit+0x5fc/0x1320 [mt_wifi]) [ 20.332563] 7981@C00L1,hc_init_ChCtrl() 2161: Clear ChCtrl Band[0] (caller:RT MPSetProfileParameters+0x90/0xf9b0 [mt_wifi]) [ 20.343850] 7981@C00L1,hc_init_ChCtrl() 2161: Clear ChCtrl Band[1] (caller:RT MPSetProfileParameters+0x90/0xf9b0 [mt_wifi]) [ 20.357333] 7981@C12L1,RTMPWirelessModeCfg() 610: Init: BSS0 PhyMode=78 [ 20.363965] 7981@C12L1,RTMPWirelessModeCfg() 610: Init: BSS1 PhyMode=177 [ 20.370973] 7981@C23L3,auto_ch_select_set_cfg() 3466: BandIdx0, AutoChannelAt Bootup=0, AutoChannelAlg = 0 [ 20.380555] 7981@C23L3,auto_ch_select_set_cfg() 3466: BandIdx1, AutoChannelAt Bootup=0, AutoChannelAlg = 0 [ 20.430273] 7981@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFP C=1 [ 20.437683] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFP C=1 [ 20.449096] WiFi@C12L1,rtmp_read_ap_client_from_file() 1638: APCLI[0] ApCliMu MimoDlEnable = 0 [ 20.457651] WiFi@C12L1,rtmp_read_ap_client_from_file() 1638: APCLI[1] ApCliMu MimoDlEnable = 0 [ 20.466358] WiFi@C12L1,rtmp_read_ap_client_from_file() 1657: APCLI[0] ApCliMu MimoUlEnable = 0 [ 20.474914] WiFi@C12L1,rtmp_read_ap_client_from_file() 1657: APCLI[1] ApCliMu MimoUlEnable = 0 [ 20.485223] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 20.496455] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension co mmand type = 48 [ 20.504936] WiFi@C03L1,AndesSendCmdMsg() 754: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 20.516175] WiFi@C03L2,AndesSendCmdMsg() 765: Command type = ed, Extension co mmand type = 48 [ 20.555395] wdma_dma_ctrl(): WDMA_GLO_CFG=50404e70, txrx = 0 [ 20.566696] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e70, txrx = 0 [ 20.582278] warp_tx_ring_init_hw(): configure ring 0 setting [ 20.587966] warp_tx_ring_init_hw(): wed:00000000024442c7 wifi:00000000594bf36 2: 24420=4cd78000,24424=2048,24428=0 [ 20.598254] warp_tx_ring_init_hw(): configure ring 1 setting [ 20.603934] warp_tx_ring_init_hw(): wed:00000000024442c7 wifi:00000000594bf36 2: 24430=476f0000,24434=2048,24438=0 [ 20.614322] set_rrocfg,0 [ 20.644211] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e74, txrx = 3 [ 20.649881] using E1 ROM patch [ 20.652926] using E1 RAM [ 20.655491] current sync CR = 0x1 [ 20.662242] Built date: 20221208201745a [ 20.666234] Platform: ALPS [ 20.669025] HW/SW version: 0x8a108a10 [ 20.672808] Patch version: 0xffffffff [ 20.684517] current sync CR = 0x1 [ 20.817112] sh (3722): drop_caches: 3 [ 21.142923] Chip ID: 0x14 [ 21.145660] Eco version: 0x00 [ 21.148708] Region number: 0x0b [ 21.151944] Format version: 0x02 [ 21.155258] Format flag: 0x01 [ 21.158312] Ram version: ____000000 [ 21.161897] Built date: 20221208201806 [ 21.165753] Common crc: 0x67d5580a [ 21.169249] Release info: header tag = 0, total length = 64 [ 21.174926] tag 1, padding length = 1, tag length = 59 [ 21.180162] payload: t-neptune-main-mt7915-1953-MT7981_MP2111_3_0-2022120820 1701 [ 21.284981] Chip ID: 0x00 [ 21.287716] Eco version: 0x00 [ 21.290798] Region number: 0x03 [ 21.294043] Format version: 0x02 [ 21.297364] Format flag: 0x01 [ 21.300411] Ram version: DEV_000000 [ 21.304001] Built date: 20221208202048 [ 21.307860] Common crc: 0x7ef0a69a [ 21.311351] Release info: header tag = 0, total length = 0 [ 21.398485] current sync CR = 0x7 [ 21.404059] efuse_probe: efuse = deaddead [ 21.440678] WiFi@C02L1,is_cal_free_ic() 831: [[32m[a-die version:1][[m [ 23.721056] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now! [ 23.728587] WiFi@C01L1,AntCfgInit() 3126: Not support for HIF_MT yet! [ 23.752578] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet! [ 23.758399] WiFi@C12L1,SCS_init() 880: INIT SCSEnable [0]= 1 [ 23.764077] WiFi@C12L1,SCS_init() 887: INIT SCSEnable [1]= 0 [ 23.769850] WiFi@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 23.775351] WiFi@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 23.780795] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited! [ 23.807687] wdma_dma_ctrl(): WDMA_GLO_CFG=50804e75, txrx = 3 [ 23.813451] WiFi@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 23.818956] WiFi@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 23.824428] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.834336] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13535: DAT config band(0) cck_timeout Fail! [ 23.843029] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.852934] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13546: DAT config band(0) ofdm_timeout Fail! [ 23.861713] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.871618] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13557: DAT config band(0) ofdma_timeout Fail! [ 23.880484] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.890388] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13535: DAT config band(1) cck_timeout Fail! [ 23.899079] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.908983] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13546: DAT config band(1) ofdm_timeout Fail! [ 23.917762] WiFi@C00L1,set_ack_timeout_mode_byband() 13447: CTS/ACK Timeout R ange should between [0xFFFF:0]!! [ 23.927666] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13557: DAT config band(1) ofdma_timeout Fail! [ 23.937600] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wi fi] [ 23.946506] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wi [ 24.075004] 7981@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1 [ 24.084220] 7981@C00L1,MtCmdCr4RedSet() 914: MtCmdCr4RedSet: (ret = 0) [ 24.090783] 7981@C00L1,SendRedCmd() 1049: SendRedCmd:(ret = 1) [ 24.096903] 7981@C01L2,RTMP_COM_IoctlHandle() 1491: -> CMD_RTPRIV_IOCTL_VIRT UAL_INF_UP [ 24.104951] WiFi@C01L3,wifi_sys_open() 856: wdev idx = 0 [ 24.110562] 7981@C18L3,BuildChannelList() 484: [ 24.115149] 7981@C00L3,BuildChannelList() 514: BandIdx = 0, PhyMode = 78, ChL istNum = 11: [ 24.123365] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.129733] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.136208] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.142588] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.149055] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.155426] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.161885] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.168265] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.174733] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.181098] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.187572] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.193952] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.200425] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.206803] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.213264] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.219637] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.226106] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.232480] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.238950] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.245322] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.251792] 7981@C14L1,vht80_channel_group() 1584: invalid ch_band 0 [ 24.258163] 7981@C14L1,vht160_channel_group() 1655: invalid ch_band 0 [ 24.264629] 7981@C23L1,DfsBuildChannelList() 3839: [RDM]: wdev is not 5G. [ 24.271458] 7981@C23L3,RadarStateCheck() 250: Zero Wait State: 0 [ 24.277583] 7981@C23L3,DfsRadarChannelCheck() 3228: [DfsRadarChannelCheck]: w dev is not 5G [ 24.285922] 7981@C23L3,operate_loader_phy() 360: oper_cfg: prim_ch(6), ht_bw( 1), extcha(1), vht_bw(1), cen_ch_2(0), PhyMode=78! [ 24.297433] 7981@C23L3,operate_loader_phy() 374: oper_dev after adjust: bw(1) , prim_ch(6), cen_ch_1(8), cen_ch_2(0),ext_cha(1)! [ 24.308933] 7981@C23L3,operate_loader_phy() 393: oper_dev after decision: bw( 1), prim_ch(6), cen_ch_1(8), cen_ch_2(0)! [ 24.319651] 7981@C23L3,DfsRadarChannelCheck() 3228: [DfsRadarChannelCheck]: w dev is not 5G [ 24.327938] 7981@C08L1,AsicSwitchChannel() 334: AsicSwitchChannel::bandIdx:0 ch_band:0 htbw:1 vht_bw:0 bw:1 extcha:1 [ 24.338479] 7981@C08L1,AsicSwitchChannel() 339: AsicSwitchChannel::primch:6 c ench1:8 cench2:0 rxstream:2 ap_bw:0 apCenCh:0 Scan:0 [ 24.350254] 7981@C00L1,mt7981_apply_dpd_flatness_data() 624: eeprom 0x19a bit 0 is 0, do runtime cal [ 24.359428] 7981@C03L3,MtCmdChannelSwitch() 2539: ctrl_chl=6, ctrl_ch2=0, cen t_ch=8 DBDCIdx=0, ChBand=0, BW=1, TXStream=2, RXStream=2, scan(0) [ 24.504351] 7981@C03L3,MtCmdSetTxRxPath() 2799: ctrl_chl=6, ctrl_ch2=0, cent_ ch=8, RxPath=3, BandIdx=0, ChBand=0, BW=1,TXStream=2, RXStream=3, scan(0) [ 24.518034] 7981@C12L1,EDCCAInit() 21068: EDCCA compensation: uni_compensatio n=0, bw_compensation=0, final compensation=0 [ 24.529102] 7981@C23L3,DfsCacNormalStart() 3716: wdev is not 5G [ 24.535044] 7981@C23L3,DfsRadarChannelCheck() 3228: [DfsRadarChannelCheck]: w dev is not 5G [ 24.543523] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 24.551556] wdev_attr_update(): wdevId0 = 7c:27:3c:08:40:49 [ 24.557225] WiFi@C12L1,wifi_sys_open() 907: wifi_sys_open():band0 group_idx[0 ]=0, bw_grp=16 omac=0 [ 24.566272] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=0 [ 24.572175] 7981@C02L2,AsicRadioOnOffCtrl() 2355: DbdcIdx=0 RadioOn [ 24.579152] 7981@C00L2,ApAutoChannelAtBootUp() 333: -----------------> [ 24.585848] 7981@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 24.591427] 7981@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 24.596868] 7981@C00L1,ApAutoChannelAtBootUp() 498: not A band [ 24.602731] 7981@C08L1,ap_run_at_boot() 624: [[41m ACS is disable !![[m [ 24.609555] 7981@C08L2,APStartUpForMbss() 984: ===>(caller:ap_inf_open+0x134/ 0x490 [mt_wifi]), mbss_idx:0, CfgMode:0 [ 24.620231] 7981@C15L2,APPMFInit() 121: [PMF] Security is not WPA2/WPA2PSK AE S [ 24.627492] 7981@C15L2,APPMFInit() 133: [PMF] apidx=0, MFPC=0, MFPR=0, SHA256 =0 [ 24.634910] 7981@C18L3,BuildChannelList() 484: [ 24.639683] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wi fi] [ 24.647360] WiFi@C08L2,ap_link_up() 7152: (caller:wdev_do_linkup+0x20/0x38 [m t_wifi]), wdev(0) [ 24.656013] 7981@C01L3,wifi_sys_linkup() 1231: wdev idx = 0 [ 24.661814] 7981@C00L3,wtc_acquire_groupkey_wcid() 84: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 [ 24.661814] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 24.676269] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=0 [ 24.689457] 7981@C08L3,UpdateBeaconHandler() 1928: BCN_UPDATE_INIT, OmacIdx = 0 (ra0) [ 24.697344] 7981@C08L3,UpdateBeaconHandler() 1941: Band0 BcnInitedRnd = 5 [ 24.704367] 7981@C00L1,TxCCKStreamCtrl() 20530: set wrong parameters [ 24.721186] PrintSrCmd: [ 24.721186] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.721186] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 24.735243] PrintSrCmd: [ 24.735243] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.735243] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 24.749272] PrintSrCmd: [ 24.749272] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.749272] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 24.763308] PrintSrCmd: [ 24.763308] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.763308] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 24.777424] PrintSrCmd: [ 24.777424] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.777424] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 24.791545] PrintSrCmd: [ 24.791545] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 24.791545] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 24.805690] 7981@C12L1,EDCCAInit() 21068: EDCCA compensation: uni_compensatio n=0, bw_compensation=0, final compensation=0 [ 24.816683] 7981@C03L3,MtCmdTxPwrShowInfo() 13748: ucTxPowerInfoCatg: 2, Band Idx: 0 [ 24.824466] 7981@C03L3,MtCmdTxPwrShowInfo() 13777: (ret = 0) [ 24.824572] [mtf_txpower_all_rate_info] band_idx:0 pwr:46 ChBand:2G ePAGain:0 [ 24.830140] mtk_ppe_dev_register_hook : ineterface ra0 register (1) [ 24.847535] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] r eturn!!! .. [ 25.102641] 7981@C08L2,mbss_virtual_if_open() 134: ===> rax0 [ 25.108433] 7981@C01L2,RTMP_COM_IoctlHandle() 1514: -> CMD_RTPRIV_IOCTL_VIRTU AL_INF_INIT [ 25.116562] 7981@C01L2,RTMP_COM_IoctlHandle() 1491: -> CMD_RTPRIV_IOCTL_VIRT UAL_INF_UP [ 25.124584] WiFi@C01L3,wifi_sys_open() 856: wdev idx = 1 [ 25.130245] 7981@C18L3,BuildChannelList() 484: [ 25.134811] 7981@C00L3,BuildChannelList() 514: BandIdx = 1, PhyMode = 177, Ch ListNum = 21: [ 25.143253] 7981@C23L3,DfsBuildChannelList() 3884: Done [ 25.148597] 7981@C23L3,RadarStateCheck() 250: Zero Wait State: 0 [ 25.154617] 7981@C23L3,RadarStateCheck() 280: [[1;33mRD_SILENCE_MODE [[m [ 25.161482] 7981@C23L3,operate_loader_phy() 360: oper_cfg: prim_ch(36), ht_bw (1), extcha(1), vht_bw(2), cen_ch_2(0), PhyMode=177! [ 25.173190] 7981@C23L3,operate_loader_phy() 374: oper_dev after adjust: bw(3) , prim_ch(36), cen_ch_1(50), cen_ch_2(0),ext_cha(1)! [ 25.184852] 7981@C23L3,operate_loader_phy() 393: oper_dev after decision: bw( 3), prim_ch(36), cen_ch_1(50), cen_ch_2(0)! [ 25.195736] 7981@C23L3,DfsCacNormalStart() 3750: [RDM] CAC 65 seconds start . Disable MAC TX [ 25.204229] 7981@C08L1,AsicSwitchChannel() 334: AsicSwitchChannel::bandIdx:1 ch_band:1 htbw:1 vht_bw:2 bw:3 extcha:1 [ 25.214796] 7981@C08L1,AsicSwitchChannel() 339: AsicSwitchChannel::primch:36 cench1:50 cench2:0 rxstream:2 ap_bw:0 apCenCh:0 Scan:0 [ 25.226629] 7981@C23L3,DfsSwitchCheck() 4040: DFS ByPass TX calibration. [ 25.233748] 7981@C00L1,mt7981_apply_dpd_flatness_data() 624: eeprom 0x19a bit 0 is 0, do runtime cal [ 25.242955] 7981@C03L3,MtCmdChannelSwitch() 2539: ctrl_chl=36, ctrl_ch2=0, ce nt_ch=50 DBDCIdx=1, ChBand=1, BW=3, TXStream=3, RXStream=3, scan(0) [ 25.304446] 7981@C03L3,MtCmdSetTxRxPath() 2799: ctrl_chl=36, ctrl_ch2=0, cent _ch=50, RxPath=7, BandIdx=1, ChBand=1, BW=3,TXStream=3, RXStream=7, scan(0) [ 25.323225] 7981@C12L1,EDCCAInit() 21068: EDCCA compensation: uni_compensatio n=0, bw_compensation=0, final compensation=0 [ 25.334488] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 25.342570] wdev_attr_update(): wdevId1 = 7e:27:3c:18:40:49 [ 25.348203] WiFi@C12L1,wifi_sys_open() 907: wifi_sys_open():band1 group_idx[1 ]=4, bw_grp=16 omac=0 [ 25.361128] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=1 [ 25.368144] 7981@C02L2,AsicRadioOnOffCtrl() 2355: DbdcIdx=1 RadioOn [ 25.375030] 7981@C00L2,ApAutoChannelAtBootUp() 333: -----------------> [ 25.381690] 7981@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 25.387219] 7981@C03L1,MtCmdSetMacTxRx() 10244: (ret = 0) [ 25.392623] 7981@C00L1,ApAutoChannelAtBootUp() 492: zero-wait DFS is not enab led [ 25.400019] 7981@C08L1,ap_run_at_boot() 624: [[41m ACS is disable !![[m [ 25.406807] 7981@C08L2,APStartUpForMbss() 984: ===>(caller:ap_inf_open+0x134/ 0x490 [mt_wifi]), mbss_idx:1, CfgMode:0 [ 25.417375] 7981@C15L2,APPMFInit() 121: [PMF] Security is not WPA2/WPA2PSK AE S [ 25.424600] 7981@C15L2,APPMFInit() 133: [PMF] apidx=1, MFPC=0, MFPR=0, SHA256 =0 [ 25.431908] 7981@C18L3,BuildChannelList() 484: [ 25.436627] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wi fi] [ 25.444241] WiFi@C08L2,ap_link_up() 7152: (caller:wdev_do_linkup+0x20/0x38 [m t_wifi]), wdev(1) [ 25.452870] 7981@C01L3,wifi_sys_linkup() 1231: wdev idx = 1 [ 25.458621] 7981@C00L3,wtc_acquire_groupkey_wcid() 84: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 [ 25.458621] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 25.473074] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=1 [ 25.485857] 7981@C08L3,UpdateBeaconHandler() 1928: BCN_UPDATE_INIT, OmacIdx = 0 (rax0) [ 25.493784] 7981@C08L3,UpdateBeaconHandler() 1941: Band1 BcnInitedRnd = 12 [ 25.513854] PrintSrCmd: [ 25.513854] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.513854] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 25.527895] PrintSrCmd: [ 25.527895] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.527895] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 25.541906] PrintSrCmd: [ 25.541906] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.541906] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 25.555970] PrintSrCmd: [ 25.555970] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.555970] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 25.570063] PrintSrCmd: [ 25.570063] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.570063] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 25.584156] PrintSrCmd: [ 25.584156] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 25.584156] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 25.598266] 7981@C12L1,EDCCAInit() 21068: EDCCA compensation: uni_compensatio n=0, bw_compensation=0, final compensation=0 [ 25.609230] 7981@C03L3,MtCmdTxPwrShowInfo() 13748: ucTxPowerInfoCatg: 2, Band Idx: 1 [ 25.616986] 7981@C03L3,MtCmdTxPwrShowInfo() 13777: (ret = 0) [ 25.617100] [mtf_txpower_all_rate_info] band_idx:1 pwr:43 ChBand:5G ePAGain:0 [ 25.622660] mtk_ppe_dev_register_hook : ineterface rax0 register (2)


F0: 102B 0000 FA: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [0000] T0: 0000 0234 [010F] Jump to BL NOTICE: BL2: v2.7(release):v21.02.5-134-g4292832a6a-dirty NOTICE: BL2: Built : 16:58:01, Mar 31 2023 NOTICE: WDT: disabled NOTICE: EMI: Using DDR3 settings dump toprgu registers data: 1001c000 | 00000000 0000ffe0 00000000 00000000 1001c010 | 00000fff 00000000 00f00000 00000000 1001c020 | 00000000 00000000 00000000 00000000 1001c030 | 003c0003 003c0003 00000000 00000000 1001c040 | 00000000 00000000 00000000 00000000 1001c050 | 00000000 00000000 00000000 00000000 1001c060 | 00000000 00000000 00000000 00000000 1001c070 | 00000000 00000000 00000000 00000000 1001c080 | 00000000 00000000 00000000 00000000 dump drm registers data: 1001d000 | 00000000 00000000 00000000 00000000 1001d010 | 00000000 00000000 00000000 00000000 1001d020 | 00000000 00000000 00000000 00000000 1001d030 | 00a003f1 000000ff 00100000 00000000 1001d040 | 00027e71 000200a0 00020303 000000ff 1001d050 | 00000000 00000000 00000000 00000000 1001d060 | 00000002 00000000 00000000 00000000 drm: 500 = 0xc [DDR Reserve] ddr reserve mode not be enabled yet DDR RESERVE Success 0 [EMI] ComboMCP not ready, using default setting BYTE_swap:0 BYTE_swap:0 Window Sum 548, worse bit 1, min window 68 Window Sum 568, worse bit 8, min window 68 Window Sum 334, worse bit 3, min window 38 Window Sum 344, worse bit 15, min window 40 Window Sum 342, worse bit 2, min window 40 Window Sum 362, worse bit 8, min window 44 Window Sum 358, worse bit 2, min window 42 Window Sum 372, worse bit 15, min window 44 Window Sum 372, worse bit 3, min window 44 Window Sum 386, worse bit 8, min window 46 Window Sum 386, worse bit 2, min window 46 Window Sum 400, worse bit 14, min window 48 Window Sum 396, worse bit 0, min window 48 Window Sum 410, worse bit 15, min window 48 Window Sum 406, worse bit 2, min window 48 Window Sum 422, worse bit 8, min window 52 Window Sum 428, worse bit 0, min window 52 Window Sum 434, worse bit 8, min window 52 Window Sum 430, worse bit 3, min window 52 Window Sum 438, worse bit 8, min window 54 Window Sum 444, worse bit 3, min window 52 Window Sum 450, worse bit 14, min window 54 Window Sum 450, worse bit 2, min window 54 Window Sum 454, worse bit 14, min window 54 Window Sum 456, worse bit 3, min window 56 NOTICE: EMI: Detected DRAM size: 256MB NOTICE: EMI: complex R/W mem test passed NOTICE: CPU: MT7981 (1300MHz) ERROR: No Flash Device Matched ERROR: spi nor init fail -22 NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.7(release):v21.02.5-134-g4292832a6a-dirty NOTICE: BL31: Built : 16:58:04, Mar 31 2023 NOTICE: Hello BL31!!! U-Boot 2022.07-rc3 (Mar 31 2023 - 16:57:31 +0800) CPU: MediaTek MT7981 Model: mt7981-rfb DRAM: 256 MiB Core: 32 devices, 13 uclasses, devicetree: embed Loading Environment from nowhere... OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Net: Warning: ethernet@15100000 (eth0) using random MAC address - 76:5c:35:71:c7:1c eth0: ethernet@15100000 *** U-Boot Boot Menu ***Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit1. Startup system (Default)2. Upgrade firmware3. Upgrade ATF BL24. Upgrade ATF FIP5. Upgrade single image6. Load image0. U-Boot consoleHit any key to stop autoboot: 4 Hit any key to stop autoboot: 3 Hit any key to stop autoboot: 2 Hit any key to stop autoboot: 1 SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB Reading from 0x180000 to 0x46000000, size 0x100 ... OK Reading from 0x180000 to 0x46000000, size 0x3b560c ... OK ## Loading kernel from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-5.15.141 Type: Kernel Image Compression: lzma compressed Data Start: 0x460000ec Data Size: 3864195 Bytes = 3.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x48000000 Entry Point: 0x48000000 Hash algo: crc32 Hash value: 3544f13e Hash algo: sha1 Hash value: 668bb3e3b9a77fba83715d1ee307e44656b0509b Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt yuncore_ax835 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x463af8b0 Data Size: 22533 Bytes = 22 KiB Architecture: AArch64 Load Address: 0x47000000 Hash algo: crc32 Hash value: c2a00f4b Hash algo: sha1 Hash value: e1a0700dd1eae03174e75cdfa059e941b2cd16c6 Verifying Hash Integrity ... crc32+ sha1+ OK Loading fdt from 0x463af8b0 to 0x47000000 Booting using the fdt blob at 0x47000000 Uncompressing Kernel Image Loading Device Tree to 000000004f7f0000, end 000000004f7f8804 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.15.141 (uprava@extdeb) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24580-43a0ad2d26) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Dec 4 20:38:28 2023 [ 0.000000] Machine model: YunCore AX835 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff] [ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff] [ 0.000000] node 0: [mem 0x0000000048000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632 [ 0.000000] pcpu-alloc: s29592 r8192 d31848 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240944K/262144K available (8128K kernel code, 896K rwdata, 2220K rodata, 448K init, 287K bss, 21200K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000133] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000143] pid_max: default: 32768 minimum: 301 [ 0.000425] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.000435] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001686] rcu: Hierarchical SRCU implementation. [ 0.002037] smp: Bringing up secondary CPUs ... [ 0.002346] Detected VIPT I-cache on CPU1 [ 0.002370] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.002397] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.002459] smp: Brought up 1 node, 2 CPUs [ 0.002474] SMP: Total of 2 processors activated. [ 0.002478] CPU features: detected: 32-bit EL0 Support [ 0.002483] CPU features: detected: CRC32 instructions [ 0.002509] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.002569] CPU: All CPU(s) started at EL2 [ 0.002580] alternatives: patching kernel code [ 0.005786] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.005808] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.005945] pinctrl core: initialized pinctrl subsystem [ 0.006565] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.006872] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.006900] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.006922] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.007245] thermal_sys: Registered thermal governor 'fair_share' [ 0.007249] thermal_sys: Registered thermal governor 'bang_bang' [ 0.007253] thermal_sys: Registered thermal governor 'step_wise' [ 0.007258] thermal_sys: Registered thermal governor 'user_space' [ 0.007429] ASID allocator initialised with 65536 entries [ 0.007869] pstore: Registered ramoops as persistent store backend [ 0.007875] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.017894] cryptd: max_cpu_qlen set to 1000 [ 0.020118] SCSI subsystem initialized [ 0.020270] libata version 3.00 loaded. [ 0.021338] clocksource: Switched to clocksource arch_sys_counter [ 0.021956] NET: Registered PF_INET protocol family [ 0.022040] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.022366] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.022384] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.022393] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.022413] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.022442] TCP: Hash tables configured (established 2048 bind 2048) [ 0.022505] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.022523] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.022643] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.022664] PCI: CLS 0 bytes, default 64 [ 0.025085] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.028615] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.028630] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.063612] pwm-mediatek 10048000.pwm: clock: top fail: -517 [ 0.071785] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.072598] printk: console [ttyS0] disabled [ 0.092761] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 18, base_baud = 2500000) is a ST16650V2 [ 0.705575] printk: console [ttyS0] enabled [ 0.710484] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.719815] loop: module loaded [ 0.724408] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.729383] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.736029] Creating 5 MTD partitions on "spi0.0": [ 0.740816] 0x000000000000-0x000000040000 : "BL2" [ 0.745886] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.751617] 0x000000050000-0x000000060000 : "Factory" [ 0.757109] 0x000000100000-0x000000180000 : "FIP" [ 0.762239] 0x000000180000-0x000000f80000 : "firmware" [ 0.767920] 2 fit-fw partitions found on MTD device firmware [ 0.773589] Creating 2 MTD partitions on "firmware": [ 0.778544] 0x000000000000-0x0000003c0000 : "kernel" [ 0.783970] 0x0000003c0000-0x000000e00000 : "rootfs" [ 0.789355] mtd: setting mtd6 (rootfs) as root device [ 0.794479] 1 squashfs-split partitions found on MTD device rootfs [ 0.800649] 0x000000800000-0x000000e00000 : "rootfs_data" [ 0.956313] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009500000, irq 82 [ 0.965890] i2c_dev: i2c /dev entries driver [ 0.971414] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 0.980078] NET: Registered PF_INET6 protocol family [ 0.985841] Segment Routing with IPv6 [ 0.989521] In-situ OAM (IOAM) with IPv6 [ 0.993510] NET: Registered PF_PACKET protocol family [ 0.998685] 8021q: 802.1Q VLAN Support v1.8 [ 1.003861] pstore: Using crash dump compression: deflate [ 1.051386] mt7530-mdio mdio-bus:1f: no interrupt support [ 1.060758] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode [ 1.069905] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.086828] mt7530-mdio mdio-bus:1f lan (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.107266] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.118453] DSA: tree 0 setup [ 1.125622] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.132852] Freeing unused kernel memory: 448K [ 1.171385] Run /sbin/init as init process [ 1.175473] with arguments: [ 1.178428] /sbin/init [ 1.181122] with environment: [ 1.184263] HOME=/ [ 1.186612] TERM=linux [ 1.402102] init: Console is alive [ 1.405635] init: - watchdog - [ 1.809615] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 1.839448] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 1.856963] init: - preinit - [ 2.240949] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 2.249493] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 2.258176] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 2.272053] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 4.338009] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 4.345375] jffs2_build_filesystem(): unlocking the mtd device... [ 4.345380] done. [ 4.353465] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 4.661348] random: crng init done [ 28.564398] done. [ 28.566334] jffs2: notice: (479) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 28.582852] mount_root: overlay filesystem has not been fully initialized yet [ 28.591245] mount_root: switching to jffs2 overlay [ 28.598337] overlayfs: upper fs does not support tmpfile. [ 28.605643] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. - config restore - [ 28.833590] urandom-seed: Seed file not found (/etc/urandom.seed) [ 28.882330] procd: - early - [ 28.885266] procd: - watchdog - [ 29.408700] procd: - watchdog - [ 29.412075] procd: - ubus - [ 29.467562] procd: - init - Please press Enter to activate this console. [ 29.685978] kmodloader: loading kernel modules from /etc/modules.d/* [ 29.705910] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 29.721855] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f [ 29.729074] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8 [ 29.908601] urngd: v1.0.2 started. [ 30.091580] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221208201745a [ 30.091580] [ 30.306421] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221208201806 [ 30.414140] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221208202048 [ 30.531978] PPP generic driver version 2.4.2 [ 30.537395] NET: Registered PF_PPPOX protocol family [ 30.546425] kmodloader: done loading kernel modules from /etc/modules.d/* [ 34.121745] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 34.134483] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 34.157300] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 34.166140] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 34.179670] device eth0 entered promiscuous mode [ 34.190371] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode [ 34.203761] br-lan: port 1(lan) entered blocking state [ 34.208905] br-lan: port 1(lan) entered disabled state [ 34.217221] device lan entered promiscuous mode [ 34.235107] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode [ 34.253881] br-lan: port 2(wan) entered blocking state [ 34.259027] br-lan: port 2(wan) entered disabled state [ 34.272162] device wan entered promiscuous mode [ 34.850085] br-lan: port 3(phy1-ap0) entered blocking state [ 34.855722] br-lan: port 3(phy1-ap0) entered disabled state [ 34.861532] device phy1-ap0 entered promiscuous mode [ 34.866610] br-lan: port 3(phy1-ap0) entered blocking state [ 34.872210] br-lan: port 3(phy1-ap0) entered forwarding state [ 34.878162] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 35.121390] br-lan: port 3(phy1-ap0) entered disabled state [ 35.812029] br-lan: port 4(phy0-ap0) entered blocking state [ 35.817602] br-lan: port 4(phy0-ap0) entered disabled state [ 35.823377] device phy0-ap0 entered promiscuous mode [ 35.828432] br-lan: port 4(phy0-ap0) entered blocking state [ 35.834029] br-lan: port 4(phy0-ap0) entered forwarding state [ 36.151622] br-lan: port 4(phy0-ap0) entered disabled state [ 38.395972] mt7530-mdio mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 38.403860] br-lan: port 2(wan) entered blocking state [ 38.409000] br-lan: port 2(wan) entered forwarding state [ 45.326304] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready [ 45.333030] br-lan: port 4(phy0-ap0) entered blocking state [ 45.338596] br-lan: port 4(phy0-ap0) entered forwarding state BusyBox v1.36.1 (2023-12-04 20:38:28 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r24580-43a0ad2d26 -----------------------------------------------------


Space for additional notes, links to forum threads or other resources.

  • ...
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1