XikeStor SKS8310-8X
XikeStor SKS8310-8X 8-Ports 10G L3 Managed Switch with 8 SFP+ Slots and 1 Console Port
Supported Versions
Experimental Versions
None at this time.
Hardware Highlights
Installation
Flash Layout
Find out flash layout, then add the flash layout table here (copy, paste, modify the example).
Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.
OEM easy installation
OEM installation using the TFTP method
Specific values needed for tftp
Enter values for “FILL-IN” below
| Bootloader tftp server IPv4 address | FILL-IN |
|---|---|
| Bootloader MAC address (special) | FILL-IN |
| Firmware tftp image | Latest OpenWrt release (NOTE: Name must contain “tftp”) |
| TFTP transfer window | FILL-IN seconds |
| TFTP window start | approximately FILL-IN seconds after power on |
| TFTP client required IP address | FILL-IN |
Upgrading OpenWrt
These are generic instructions. Update with your router's specifics.
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/LuCI Upgrade URL - Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrademtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
mtd
If sysupgrade does not support this router, use mtd.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
Debricking
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Please fill in real values for this device, then remove the EXAMPLEs
Network interfaces
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| br-lan | EXAMPLE LAN & WiFi | EXAMPLE 192.168.1.1/24 |
| vlan0 (eth0.0) | EXAMPLE LAN ports (1 to 4) | EXAMPLE None |
| vlan1 (eth0.1) | EXAMPLE WAN port | EXAMPLE DHCP |
| wl0 | EXAMPLE WiFi | EXAMPLE Disabled |
Switch Ports (for VLANs)
Please fill in real values for this device, then remove the EXAMPLEs
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
| Port | Switch port |
|---|---|
| Internet (WAN) | EXAMPLE 4 |
| LAN 1 | EXAMPLE 3 |
| LAN 2 | EXAMPLE 2 |
| LAN 3 | EXAMPLE 1 |
| LAN 4 | EXAMPLE 0 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
Please fill in real values for this device, then remove the EXAMPLEs
The XikeStor SKS8310-8X has the following buttons:
| BUTTON | Event |
|---|---|
| EXAMPLE Reset | reset |
| EXAMPLE Secure Easy Setup | ses |
| EXAMPLE No buttons at all. | - |
Hardware
Info
- This table is automatically generated, once the correct filters for Brand and Model are set.
- If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
- If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for XikeStor SKS8310-8X ? If not: Create one.
- If you see a table with the desired device data, everything is OK and you can delete this text and the
<WRAP>that encloses it. - If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.
---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=XikeStor filter : Model=SKS8310-8X filter : Versions=
Photos
Front:
Insert photo of front of the casing
Back:
Insert photo of back of the casing
Backside label:
Insert photo of backside label
Opening the case
→ Warranty
Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...
- To remove the cover and open the device, do a/b/c
Main PCB:
Serial
Serial connection parameters for XikeStor SKS8310-8X :
| UART | “Console” port on the front panel |
|---|---|
| type | RS-232C |
| settings | 9600n8 |
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE
OpenWrt bootlog
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING
Notes
Space for additional notes, links to forum threads or other resources.
- ...
Tags
Add tags below, then remove this fixme.