TP-Link TL-WR820N
OpenWrt support
Not supported.
Hardware Highlights
| Version | CPU | Flash | RAM | Network | USB | Serial | JTag | Notes |
|---|---|---|---|---|---|---|---|---|
| ? (CN) | Atheros QCA9531 | 4MB | 64MB | 2x 100M | Yes | ? | ? | Not supported. |
| v1.0 (BR/EU) | Mediatek MT7628KN | 1MB | 8MB | 2x 100M | No | Yes | ? | Not supported. |
| v2.0 (NL) | Mediatek MT7628KN | 2MB | 8MB | ? | ? | ? | ? | Not supported. |
Forum links
Tags
OEM bootlog (EU V1)
[DBG] sel_fine_tmp=00000008, sel_mst_fine=00000002,fg_dly_adj=0000000E [DBG] sel_fine_tmp=00000006, sel_mst_fine=00000002,fg_dly_adj=0000000C
[03060C0F][03060C0A][7C7E0000][23244648][00232452] DU Setting Cal Done
U-Boot 1.1.3 (Jul 19 2018 - 15:10:17)
Board: Ralink APSoC DRAM: 8 MB relocate_code Pointer at: 807c4000 flash manufacture id: c8, device id 40 14 find flash: GD25Q08B PA/LNA:34,0 *** Warning - bad CRC, using default environment
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
RESET MT7628 PHY!!!!!!
Please choose the operation or press ctrl + c to stop auto boot:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
## Booting image at bc00d000 ...
addr:0xbc00d000
vxWorks Image.
imgFileEnc=0xbc00d080, offset=0x80, len=0xb65f1
enter sysGpioInit
Before exit sysClkConnect!
In sysClkEnable!
Before exit sysClkEnable!
Attachin
g in teWrfaacie tlot0.i..n dgon ef
or RX_DMA_BUSY status Start... done
Tx_Ring addr: 0xa05e11c0!!!
Rx_Ring addr: 0xa05e0520!!! minifs.fileCount=92 minifs.nameTableSize=1348 minifs.fileIndex=bc0c4564 minifs.ballCount=7 minifs.fileIndex initialized minifs.ballIndex initialized minifs.ballData=BC0C4CCC minifs.oemSize=274 minifs.oemData=BC0F3801
Version2.0
Software Platform for PNE2.2
Copyright(C) 2001-2011 by TP-LINK TECHNOLOGIES CO., LTD.
Creation date: May 6 2019, 09:56:18
# eth0 macAddr = 00-19-66-FFFFFFCA-FFFFFF8B-07
eth0 macAddr = FFFFFF98-FFFFFFDA-FFFFFFC4-FFFFFFCD-FFFFFFF8-FFFFFF90
TimeZone=GMT+1
Decompress config 0x3d50
Vlan Table: ------------------------------------------------ VID Pri TagMember UntagMember Device 2 00 0x40 0x02 eth1 1 00 0x40 0x0c eth0 ------------------------------------------------
set mii port 1 value 0x00003100
mt7628_phy_off port: 1
mt7628_phy_on port: 1
RTA_DST:
AF_INET 0.0.0.0
RTA_NETMASK:
Not AF_INET/AF_INET6
Error writing to routing socket
delete net 0.0.0.0: not in table
RTA_DST:
AF_INET 0.0.0.0
RTA_NETMASK:
AF_INET 0.0.0.0
Error writing to routing socket
delete net default: not in table
RTA_DST:
AF_INET 0.0.0.0
RTA_GATEWAY:
AF_INET 97.91.254.169
RTA_NETMASK:
AF_INET 0.0.0.0
add net default: gateway 169.254.91.97
RTA_DST:
AF_INET 0.91.254.169
RTA_NETMASK:
Not AF_INET/AF_INET6
change net 169.254.91.0
RTA_DST:
AF_INET 0.0.0.0
RTA_NETMASK:
Not AF_INET/AF_INET6
change net 0.0.0.0
FW Version:_e2_mp
FW Build Date:20140925171453
803CFAF0: - 28 76 (v
803CFB00: 06 00 00 0C 43 E1 76 28 - 00 00 00 00 00 00 FF FF ....C.v( ........
803CFB10: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF 00 00 ........ ........
803CFB20: 00 00 20 00 00 00 00 00 - 00 00 00 00 00 00 00 00 .. ..... ........
803CFB30: 00 00 22 34 00 20 FF FF - 00 01 00 00 00 00 00 00 .."4. .. ........
803CFB40: 22 00 00 00 00 00 30 00 - 00 00 00 00 00 00 00 00 ".....0. ........
803CFB50: 00 94 40 BA C0 CC 20 86 - 85 85 40 CC 20 85 85 85 ..@... . ..@. ...
803CFB60: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ........ ........
803CFB70: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ........ ........
803CFB80: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ........ ........
803CFB90: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 C0 C0 ........ ........
803CFBA0: C0 C0 C0 C0 C0 C0 C0 C0 - C0 C0 C0 C0 00 00 00 00 ........ ........
803CFBB0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ........ ........
803CFBC0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ........ ........
803CFBD0: 00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 11 1D ........ ........
803CFBE0: 11 1D 1C 35 1C 35 1E 35 - 1E 35 17 19 17 19 02 00 ...5.5.5 .5......
803CFBF0: 00 00 C9 C8 C5 88 00 00 - 00 00 00 00 00 00 FF FF ........ ........
803CFC00: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC10: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF 00 00 ........ ........
803CFC20: 00 00 00 00 00 00 00 00 - 00 00 00 00 77 00 11 1D ........ ....w...
803CFC30: 11 1D 15 7F 15 7F 17 7F - 17 7F 10 3B 10 3B 59 FF ..... ..;.;Y.
803CFC40: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC50: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC60: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC70: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC80: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFC90: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCA0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCB0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCC0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCD0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCE0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF FF FF ........ ........
803CFCF0: FF FF FF FF FF FF FF FF - FF FF FF FF FF FF 00 00 ........ ........
WTBL Segment 1 info:
MemBaseAddr/FID:0x28000/0
EntrySize/Cnt:32/128
WTBL Segment 2 info:
MemBaseAddr/FID:0x40000/0
EntrySize/Cnt:64/128
WTBL Segment 3 info:
MemBaseAddr/FID:0x42000/64
EntrySize/Cnt:64/128
WTBL Segment 4 info:
MemBaseAddr/FID:0x44000/128
EntrySize/Cnt:32/128
===============qadInit===============
# # # # help
- -----------------------------------------------------------------------
Version = 2.0.
Task name = tCmdTask, pri = 8, stack size = 10240, max command entry num = 32.
command description -------------------------------------------------------------------- ? print all commands. help print all commands. mem show memory part, pools, and dump memory. task show task info and manage system task. tftp download or upload files by tftp protocol. ifconfig Interface config, please reference to -help command. route Show route table, delete/add special route entry. arp Show all arp entries, delete/add special arp entry. net Show net runtimes. ping6 Send ICMPv6 ECHO_REQUEST to IPv6 nodes. track Show conntrack runtimes, modify conntrack environments. register register show. packet packet show. flash Print flash layout, read/write/erase specify flash. port manage all udp/tcp packet ports. mcb Show mcb pools or blocks. bridge Show all bridge stations. nat Show nat runtimes. system reboot, reset or firmware. wioctl Wlan command line utility. iwpriv MTK Wlan command line utility. wpkt MTK WiFi Tx mem pool monitor utility. -------------------------------------------------------------------- # flash layout
# flash -layout # flash -erase off len # flash -read off len buffer # flash -write off len buffer # # -layout Show flash layout. # -erase Erase specify flash segment. # -read Read specify flash segment to buffer. # -write write specify flash segment from buffer. # # off Offset of flash. # len Length of specify flash segment. # buffer Buffer write from or read to. # # flash layout -layout
Version: 2.0 Name: FlashIo Total Size(K): 1024 Erase Sector Size(K): 4 Block Num: 6. ================================================== Flash Layout: |------------------------| 0x00000000(0K) | | | | |BOOTIMG(52K) | | | | | |------------------------| 0x0000d000(52K) | | | | |FIRMWARE(948K) | | | | | |------------------------| 0x000fa000(1000K) |CONFIG(8K) | |------------------------| 0x000fc000(1008K) |EXPLOG(8K) | |------------------------| 0x000fe000(1016K) |PROFILE(4K) | |------------------------| 0x000ff000(1020K) |RADIO(4K) | |------------------------| 0x00100000(1024K) # ?
- -----------------------------------------------------------------------
Version = 2.0.
Task name = tCmdTask, pri = 8, stack size = 10240, max command entry num = 32.
command description -------------------------------------------------------------------- ? print all commands. help print all commands. mem show memory part, pools, and dump memory. task show task info and manage system task. tftp download or upload files by tftp protocol. ifconfig Interface config, please reference to -help command. route Show route table, delete/add special route entry. arp Show all arp entries, delete/add special arp entry. net Show net runtimes. ping6 Send ICMPv6 ECHO_REQUEST to IPv6 nodes. track Show conntrack runtimes, modify conntrack environments. register register show. packet packet show. flash Print flash layout, read/write/erase specify flash. port manage all udp/tcp packet ports. mcb Show mcb pools or blocks. bridge Show all bridge stations. nat Show nat runtimes. system reboot, reset or firmware. wioctl Wlan command line utility. iwpriv MTK Wlan command line utility. wpkt MTK WiFi Tx mem pool monitor utility. -------------------------------------------------------------------- # mem
# mem -show [sys | dada | object] # mem -dump start size # mem -md start value # # -show Displays alloced/free mempry blocks and size. # -dump dump specify memory block. # -md copy specify memory block to specify address. # # start Start address of specify memory block, in hex. # size Size of specify memory block, in hex. # value value in UINT32 format. # object end object, e.g:eth 0. # # Example: # mem -dump 80010000 1000 .... Show memory block start at 0x80010000 which size of 4k. # mem -show eth 1 .... Show netpool of end object eth1. # mem -show
FREE LIST:
num addr size
---- ---------- ----------
1 0x801d6ac0 15984
2 0x807f3810 22560
3 0x807f3660 96
4 0x801dcca0 48
5 0x801d1570 21504
6 0x807ed080 16
7 0x806e6ac0 32
8 0x805ccde0 16
9 0x805ccc20 16
10 0x8045e5c0 80
11 0x8045df80 80
12 0x801d69c0 80
SUMMARY:
status bytes blocks avg block max block
------ ---------- --------- ---------- ----------
current
free 60512 12 5042 22560
alloc 6422016 1165 5512 -
cumulative
alloc 11363520 4192 2710 -
# ifconfig
# ifconfig -show [devName devNum]
# ifconfig -attach devName devNum
# ifconfig -detach devName devNum
# ifconfig -napt devName devNum up|down
# ifconfig -param
#
# -show Show specify or all interface.
# -attach Attach specify interface.
# -detach Detach specify interface.
# -napt Tagged an interface to napt port.
#
# param Params pass to ifconfig.
#
# Example:
# ifconfig eth1 inet 172.31.70.103 netmask 255.255.255.0
# .... Call ifconfig, and pass
# "eth1 inet 172.31.70.103 netmask 255.255.255.0" to it.
# ifconfig -show eth 1 .... Show interface eth1.
#
ifconfig -show
lo (unit number 0):
Flags: (0xc8049) UP LOOPBACK MULTICAST TRAILERS ARP RUNNING INET_UP INET6_UP
Type: SOFTWARE_LOOPBACK
inet: 127.0.0.1
Netmask 0xff000000 Subnetmask 0xff000000
inet6: ::1 prefixlen 128
inet6: fe80::1%lo0 scopeid 0x1 prefixlen 64
Metric is 0
Maximum Transfer Unit size is 1536
0 packets received; 0 packets sent
0 multicast packets received
0 multicast packets sent
0 input errors; 0 output errors
0 collisions; 0 dropped
0 output queue drops
mirror (unit number 0):
Flags: (0x68143) UP BROADCAST MULTICAST PROMISCUOUS ARP RUNNING INET_UP
Type: ETHERNET_CSMACD
inet: 192.168.0.1
Broadcast address: 192.168.0.255
Netmask 0xffffff00 Subnetmask 0xffffff00
Ethernet address is 98:da:c4:cd:f8:90
Metric is 0
Maximum Transfer Unit size is 1500
0 octets received
0 octets sent
0 unicast packets received
23 unicast packets sent
0 non-unicast packets received
20 non-unicast packets sent
0 incoming packets discarded
0 outgoing packets discarded
0 incoming errors
0 outgoing errors
0 unknown protos
0 collisions; 0 dropped
0 output queue drops
eth (unit number 1):
Flags: (0x40068143) UP BROADCAST MULTICAST PROMISCUOUS ARP RUNNING NAPT INET_UP
Type: ETHERNET_CSMACD
inet: 169.254.91.97
Broadcast address: 169.254.91.255
Netmask 0xffff0000 Subnetmask 0xffffff00
Ethernet address is 98:da:c4:cd:f8:91
Metric is 0
Maximum Transfer Unit size is 1500
0 octets received
64 octets sent
0 unicast packets received
1 unicast packets sent
0 non-unicast packets received
0 non-unicast packets sent
0 incoming packets discarded
0 outgoing packets discarded
0 incoming errors
0 outgoing errors
0 unknown protos
0 collisions; 0 dropped
0 output queue drops
ppp (unit number 0):
Flags: (0x400080d1) UP POINT-TO-POINT MULTICAST TRAILERS RUNNING NAPT
Type: PPP
Metric is 0
Maximum Transfer Unit size is 1492
0 octets received
0 octets sent
0 unicast packets received
0 unicast packets sent
0 non-unicast packets received
0 non-unicast packets sent
0 incoming packets discarded
0 outgoing packets discarded
0 incoming errors
0 outgoing errors
0 unknown protos
0 output queue drops