Show pagesourceOld revisionsBacklinksBack to top × Table of Contents Serial log of flash procedure Version 1.x Version 2.x Serial log of flash procedure Version 1.x U-Boot 1.1.4 (Nov 17 2009 - 11:56:26) AP83 (ar9100) U-boot 0.0.11 DRAM: sri 32 MB id read 0x100000ff flash size 8MB, sector count = 128 Flash: 8 MB Using default environment In: serial Out: serial Err: serial Net: ag7100_enet_initialize... No valid address in Flash. Using fixed address : cfg1 0xf cfg2 0x7114 eth0: 00:03:7f:09:0b:ad eth0 up eth0 Autobooting in 1 secondsar7100> erase 0xbf020000 +7c0000 First 0x2 last 0x7d sector size 0x10000 125 Erased 124 sectors ar7100> ar7100> tftpboot 0x81000000 code.bin dup 1 speed 1000 Using eth0 device TFTP from server 192.168.0.5; our IP address is 192.168.0.2 Filename 'code.bin'. Load address: 0x81000000 Loading: T T T checksum bad T ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ done Bytes transferred = 8126464 (7c0000 hex) ar7100> ar7100> cp.b 0x81000000 0xbf020000 0x7c0000 Copy to Flash... write addr: bf020000 done ar7100> bootm 0xbf020000 ## Booting image at bf020000 ... Uncompressing Kernel Image ... OK Starting kernel ... Linux version 2.6.32.10 (openwrt@wrt1.marcant.net) (gcc version 4.3.3 (GCC) ) #20 Tue Apr 6 15:01:26 CEST 2010 bootconsole [early0] enabled CPU revision is: 00019374 (MIPS 24Kc) Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00002000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00002000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=TL-WR1043ND PID hash table entries: 128 (order: -3, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 29332k/32768k available (2101k kernel code, 3436k reserved, 397k data, 152k init, 0k highmem) SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. NR_IRQS:56 Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200) Mount-cache hash table entries: 512 NET: Registered protocol family 16 MIPS: machine is TP-LINK TL-WR1043ND bio: create slab <bio-0> at 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering mini_fo version $Id$ JFFS2 version 2.2. (NAND) (SUMMARY) ■■ 2001-2006 Red Hat, Inc. yaffs Mar 28 2010 17:53:41 Installing. msgmni has been set to 57 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled Atheros AR71xx SPI Controller driver version 0.2.4 m25p80 spi0.0: s25sl064a (8192 Kbytes) Searching for RedBoot partition table in spi0.0 at offset 0x7f0000 No RedBoot partition table detected in spi0.0 spi0.0: no WRT160NL signature found Creating 5 MTD partitions on "spi0.0": 0x000000000000-0x000000020000 : "u-boot" 0x000000020000-0x000000160000 : "kernel" 0x000000160000-0x0000007f0000 : "rootfs" mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=2A0000, len=550000 0x0000002a0000-0x0000007f0000 : "rootfs_data" 0x0000007f0000-0x000000800000 : "art" 0x000000020000-0x0000007f0000 : "firmware" Realtek RTL8366RB ethernet switch driver version 0.2.0 rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK) rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found rtl8366-rtl: probed eth0: Atheros AG71xx at 0xb9000000, irq 4 Atheros AR71xx hardware watchdog driver version 0.1.0 TCP westwood registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 152k freed Please be patient, while OpenWrt loads ... gpio-buttons driver version 0.1.2 input: gpio-buttons as /devices/platform/gpio-buttons/input/input0 Button Hotplug driver version 0.3.1 eth0: link up (1000Mbps/Full duplex) - preinit - Registered led device: tl-wr1043nd:green:usb Registered led device: tl-wr1043nd:green:system Registered led device: tl-wr1043nd:green:qss Registered led device: tl-wr1043nd:green:wlan Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - jffs2 not ready yet; using ramdisk mini_fo: using base directory: / mini_fo: using storage directory: /tmp/root - init - eth0: link down Please press Enter to activate this console. eth0: link up (1000Mbps/Full duplex) device eth0.1 entered promiscuous mode device eth0 entered promiscuous mode br-lan: port 1(eth0.1) entering forwarding state PPP generic driver version 2.4.2 ip_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 24 nf_conntrack version 0.5.0 (460 buckets, 1840 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 jffs2_build_filesystem(): unlocking the mtd device... done. jffs2_build_filesystem(): erasing all blocks after the end marker... done. mini_fo: using base directory: / mini_fo: using storage directory: /overlay Version 2.x U-Boot 1.1.4 (Jul 17 2015 - 14:31:22) ap135 - Scorpion 1.0DRAM: sri Scorpion 1.0 ath_ddr_initial_config(178): (16bit) ddr2 init tap = 0x00000003 Tap (low, high) = (0x0, 0x1e) Tap values = (0xf, 0xf, 0xf, 0xf) 64 MB Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x17 flash size 8MB, sector count = 128 Flash: 8 MB Using default environment *** Warning *** : PCIe WLAN Module not found !!! *** Warning *** : PCIe WLAN Module not found !!! In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... athrs_sgmii_res_cal: cal value = 0xe No valid address in Flash. Using fixed address No valid address in Flash. Using fixed address ath_gmac_enet_initialize: reset mask:c02200 Scorpion ----> S17 PHY * athrs17_reg_init: complete : cfg1 0x80000000 cfg2 0x7114 eth0: ba:be:fa:ce:08:41 eth0 up athrs17_reg_init_wan done SGMII in forced mode athr_gmac_sgmii_setup SGMII done : cfg1 0x800c0000 cfg2 0x7214 eth1: ba:be:fa:ce:08:41 eth1 up eth0, eth1 Setting 0x18116290 to 0x58b1a14f is_auto_upload_firmware=0 Autobooting in 1 seconds ap135> tftp 0x80060000 openwrt-15.05-ar71xx-generic-tl-wr1043nd-v2-squashfs-factory.bin dup 1 speed 1000 Using eth1 device TFTP from server 192.168.1.100; our IP address is 192.168.1.111 Filename 'openwrt-15.05-ar71xx-generic-tl-wr1043nd-v2-squashfs-factory.bin'. Load address: 0x80060000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################ done Bytes transferred = 8126464 (7c0000 hex) ap135> erase 0x9f020000 +0x7c0000 Erasing flash... First 0x2 last 0x7d sector size 0x10000 125 Erased 124 sectors ap135> cp.b 0x80060000 0x9f020000 0x7c0000 Copy to Flash... write addr: 9f020000 done ap135> boot.m 0x9f020000 ## Booting image at 9f020000 ... Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 21:55:57 CEST 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9558 ver 1 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=TL-WR1043ND-v2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61004K/65536K available (2621K kernel code, 129K rwdata, 344K rodata, 224K init, 194K bss, 4532K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:720.000MHz, DDR:600.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.070000] NET: Registered protocol family 16 [ 0.080000] MIPS: machine is TP-LINK TL-WR1043ND v2 [ 0.520000] Switched to clocksource MIPS [ 0.530000] NET: Registered protocol family 2 [ 0.530000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.530000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.540000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.540000] TCP: reno registered [ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.560000] NET: Registered protocol family 1 [ 0.560000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.590000] msgmni has been set to 119 [ 0.590000] io scheduler noop registered [ 0.600000] io scheduler deadline registered (default) [ 0.600000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.640000] console [ttyS0] enabled [ 0.640000] console [ttyS0] enabled [ 0.650000] bootconsole [early0] disabled [ 0.650000] bootconsole [early0] disabled [ 0.660000] m25p80 spi0.0: found s25fl064k, expected m25p80 [ 0.670000] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 0.680000] 5 tp-link partitions found on MTD device spi0.0 [ 0.680000] Creating 5 MTD partitions on "spi0.0": [ 0.690000] 0x000000000000-0x000000020000 : "u-boot" [ 0.690000] 0x000000020000-0x00000012c508 : "kernel" [ 0.700000] 0x00000012c508-0x0000007f0000 : "rootfs" [ 0.700000] mtd: device 2 (rootfs) set to be root filesystem [ 0.720000] 1 squashfs-split partitions found on MTD device rootfs [ 0.720000] 0x000000360000-0x0000007f0000 : "rootfs_data" [ 0.730000] 0x0000007f0000-0x000000800000 : "art" [ 0.730000] 0x000000020000-0x0000007f0000 : "firmware" [ 0.750000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0 [ 0.840000] libphy: ag71xx_mdio: probed [ 1.440000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316] [ 1.450000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.040000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:SGMII [ 2.040000] TCP: cubic registered [ 2.050000] NET: Registered protocol family 17 [ 2.050000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.060000] Bridge firewalling registered [ 2.070000] 8021q: 802.1Q VLAN Support v1.8 [ 2.080000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 2.090000] Freeing unused kernel memory: 224K (80368000 - 803a0000) [ 3.160000] init: Console is alive [ 3.160000] init: - watchdog - [ 4.370000] usbcore: registered new interface driver usbfs [ 4.370000] usbcore: registered new interface driver hub [ 4.380000] usbcore: registered new device driver usb [ 4.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.400000] ehci-platform: EHCI generic platform driver [ 4.400000] ehci-platform ehci-platform.0: EHCI Host Controller [ 4.410000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 4.420000] ehci-platform ehci-platform.0: TX-TX IDP fix enabled [ 4.420000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 4.450000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 4.450000] hub 1-0:1.0: USB hub found [ 4.460000] hub 1-0:1.0: 1 port detected [ 4.460000] ehci-platform ehci-platform.1: EHCI Host Controller [ 4.470000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 4.480000] ehci-platform ehci-platform.1: TX-TX IDP fix enabled [ 4.480000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 4.510000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 4.510000] hub 2-0:1.0: USB hub found [ 4.520000] hub 2-0:1.0: 1 port detected [ 5.170000] init: - preinit - [ 5.690000] eth1: link up (1000Mbps/Full duplex) [ 5.710000] random: procd urandom read with 9 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.960000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 8.990000] eth1: link down [ 9.000000] procd: - early - [ 9.010000] procd: - watchdog - [ 9.620000] procd: - ubus - [ 10.630000] procd: - init - Please press Enter to activate this console. [ 11.270000] NET: Registered protocol family 10 [ 11.280000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.290000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 11.300000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 11.310000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.320000] nf_conntrack version 0.5.0 (956 buckets, 3824 max) [ 11.350000] xt_time: kernel timezone is -0000 [ 11.370000] cfg80211: Calling CRDA to update world regulatory domain [ 11.390000] cfg80211: World regulatory domain updated: [ 11.390000] cfg80211: DFS Master region: unset [ 11.390000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.410000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 11.420000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 11.430000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.440000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 11.450000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 11.450000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 11.460000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 11.510000] PPP generic driver version 2.4.2 [ 11.520000] NET: Registered protocol family 24 [ 11.590000] ieee80211 phy0: Atheros AR9550 Rev:0 mem=0xb8100000, irq=47 [ 11.620000] cfg80211: Calling CRDA for country: US [ 11.620000] cfg80211: Regulatory domain changed to country: US [ 11.630000] cfg80211: DFS Master region: FCC [ 11.630000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 11.640000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 11.650000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A) [ 11.660000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 11.670000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 11.680000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 18.660000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 18.680000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 18.680000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 20.420000] eth1: link up (1000Mbps/Full duplex) [ 20.420000] device eth1 entered promiscuous mode [ 20.460000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 20.520000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 21.420000] br-lan: port 1(eth1) entered forwarding state [ 21.420000] br-lan: port 1(eth1) entered forwarding state [ 21.450000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 21.780000] eth0: link up (1000Mbps/Full duplex) [ 21.780000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.420000] br-lan: port 1(eth1) entered forwarding state [ 23.880000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up [ 23.880000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 5 is up [ 40.430000] done. [ 40.430000] jffs2: notice: (1023) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 76.400000] random: nonblocking pool is initialized This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies Last modified: 2015/09/20 09:23by JaHa