TP-Link EC330-G5u v1
The TP-Link EC330-G5u v1 is a WiFi 5 AC1900 wireless router based on the MT7621 platform with USB 3.0 port.
It's also known as TP-Link Archer C9ERT.
Supported Versions
Experimental Versions
Hardware Highlights
Installation
OpenWrt installation (using factory image)
Tested with 3.16.0 0.9.1 v6037.0 Build 191016 Rel.30619nb TP-Link firmware. Also tested on 3.16.0 0.9.1 v6037.0 Build 181229 Rel.41159n (ISP's default FW) if the router booted from the right slot to download the OpenWrt firmware (see step 6 below).
1. Login to the router web interface (http://192.168.0.1/ by default) and save running config to conf.bin file
2. Open configuration file in any TP-Link config editor (e.g. https://jahed.github.io/tp-link-config-editor/)
3. Find DeviceInfo section and insert a new string:
<Description val="Modem Router`telnetd -p 1023 -l login`" />
according to the following example:
<DeviceInfo> ... <Description val="Modem Router`telnetd -p 1023 -l login`" /> ... </DeviceInfo>
4. Save configuration file and upload changed configuration using stock firmware web interface
5. Login using telnet to IP:192.168.0.1, port:1023 (Username:admin, password:1234)
6. Run
cat /proc/mtd | grep mtd7
- If the result is
mtd7: 03000000 00020000 "rootfs" 03400000then install stock firmware using web interface to toggle booted firmware image from os1 to os0
- If the result is
mtd7: 03000000 00020000 "rootfs" 00400000then all is ok, go to the next step
7. Set up a tftp server (e.g. tftpd64 for windows) with OpenWrt factory.bin image (IP:192.168.0.100 in this example)
8. Login using telnet to 192.168.0.1, port:1023
9. Download OpenWrt factory.bin image from the tftp server:
cd /tmp tftp -g -r factory.bin 192.168.0.100
10. Write OpenWrt factory.bin image:
dd if=/tmp/factory.bin of=/dev/mtdblock1
11. Power cycle the router
OpenWrt installation (using serial console)
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server with IP 192.168.0.5
2. Attach Serial console (UART)
3. Switch on the router and interrupt the boot process by pressing 't'
4. Load and run OpenWrt initramfs image:
tftpboot bootm
5. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
6. Run
sysupgrade -n
with the sysupgrade OpenWrt image
Back to Stock
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Flash Layout
| Offset | Size | Size | End | Partition | MTD | Comment | |
|---|---|---|---|---|---|---|---|
| 0x0 | 0x400000 | 4 Mb | 0x400000 | (uboot)ro | mtd0 | 0x0 | U-Boot version string, “U-Boot 1.1.3 (Mar 18 2019 - 12:50:24)” |
| uImage header, header size: 64 bytes, header CRC: 0xFF0BD54E, created: 2019-03-18 12:50:28, image size: 108120 bytes, Data Address: 0xA0200000, Entry Point: 0xA0200000, data CRC: 0xDE252645, OS: Linux, CPU: MIPS, image type: Standalone Program, compression type: none, image name: “NAND Flash I” | |||||||
| THIS IS First Uboot: The first uboot located in NAND Flash to load next full-feature Uboot. | |||||||
| 0x20000 | U-Boot version string, “U-Boot 1.1.3 (Mar 18 2019 - 12:50:29)” | ||||||
| uImage header, header size: 64 bytes, header CRC: 0x8524CA7, created: 2019-03-18 12:50:33, image size: 173024 bytes, Data Address: 0xA01FC040, Entry Point: 0xA0200000, data CRC: 0x666D4115, OS: Linux, CPU: MIPS, image type: Standalone Program, compression type: none, image name: “NAND Flash I” | |||||||
| THIS IS Main Uboot: Including recovery webserver. | |||||||
| 0x60000 | U-Boot version string, “U-Boot 1.1.3 (Mar 18 2019 - 12:50:29)” | ||||||
| uImage header, header size: 64 bytes, header CRC: 0x8524CA7, created: 2019-03-18 12:50:33, image size: 173024 bytes, Data Address: 0xA01FC040, Entry Point: 0xA0200000, data CRC: 0x666D4115, OS: Linux, CPU: MIPS, image type: Standalone Program, compression type: none, image name: “NAND Flash I” | |||||||
| 0x400000 | 0x3000000 | 48 Mb | 0x3400000 | (os0) | mtd1 | 0x0 | All firmware header |
| uImage header, header size: 64 bytes, header CRC: 0x2195F4C5, created: 2019-10-16 08:30:26, image size: 18218944 bytes, Data Address: 0xA0200000, Entry Point: 0xA0200000, data CRC: 0xF48746FC, OS: Linux, CPU: MIPS, image type: Firmware Image, compression type: none, image name: “OS IMAGE” | |||||||
| 0x40 | U-Boot header | ||||||
| U-Boot version string, “U-Boot 1.1.3 (Oct 16 2019 - 08:14:45)” | |||||||
| uImage header, header size: 64 bytes, header CRC: 0x585AD1A1, created: 2019-10-16 08:14:49, image size: 180596 bytes, Data Address: 0xA01FB040, Entry Point: 0xA0200000, data CRC: 0xCCBF4B4B, OS: Linux, CPU: MIPS, image type: Standalone Program, compression type: none, image name: “NAND Flash I” | |||||||
| THIS IS Image Uboot: Uboot included in upgrade image. | |||||||
| 0x40000 | Kernel header | ||||||
| uImage header, header size: 64 bytes, header CRC: 0x3C92A2FC, created: 2019-10-16 08:19:42, image size: 3431340 bytes, Data Address: 0x81001000, Entry Point: 0x8161BFE0, data CRC: 0xF57CE35D, OS: Linux, CPU: MIPS, image type: OS Kernel Image, compression type: lzma, image name: “Linux Kernel Image” | |||||||
| 0x3a0000 | UBI erase count header, version: 1, EC: 0x0, VID header offset: 0x800, data offset: 0x1000 | ||||||
| 0x3400000 | 0x3000000 | 48 Mb | 0x6400000 | (os1) | mtd2 | OS IMAGE 2 | |
| 0x6400000 | 0x1000000 | 16 Mb | 0x7400000 | (userfs) | mtd3 | UBI | |
| 0x7400000 | 0x400000 | 4 Mb | 0x7800000 | (ubootenv) | mtd4 | ||
| 0x7800000 | 0x400000 | 4 Mb | 0x7c00000 | (factory) | mtd5 | 0x8000 | RF EEPROM 2g |
| 0x14000 | RF EEPROM 5g | ||||||
| 0x0 | 128M | 128 Mb | 0x7f80000 | (wholeflash) | mtd6 | Whole NAND | |
| 0x400000 | 0x3000000 | 48 Mb | 0x3400000 | (rootfs) | mtd7 | OS IMAGE 1 |
Bootloader notes
The device contains 3 bootloaders:
1. First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot located on NAND Flash to load next full-feature Uboot.
2. Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This bootloader includes recovery webserver. Requires special uImages to continue the boot process:
- 0x00 (os0, os1) - firmware uImage
- 0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
3. Additionally, both slots of the original TP-Link firmware contains Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image magics and CRCs. We don't use this U-Boot with OpenWrt.
OEM easy installation
None so far.
OEM installation using the TFTP method
None so far.
Upgrading OpenWrt
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/LuCI Upgrade URL - Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
Debricking
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload the OEM firmware
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Network interfaces
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| br-lan | LAN & WiFi | 192.168.1.1/24 |
| lan1-4 | LAN ports (1-4) | br-lan |
| wan | WAN port | DHCP |
Switch Ports (for VLANs)
| Port | Switch port |
|---|---|
| Internet (WAN) | wan |
| LAN 1 | lan1 |
| LAN 2 | lan2 |
| LAN 3 | lan3 |
| LAN 4 | lan4 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The TP-Link EC330-G5u has the following buttons:
| BUTTON | Event |
|---|---|
| Led | KEY_LIGHTS_TOGGLE |
| WiFi On/Off | KEY_RFKILL |
| Reset | reset |
| WPS | wps |
Hardware
Info
Photos
Front:
Back:
Left side:
Bottom:
Label:
Opening the case
Note: This will void your warranty!
- There are crews at the bottom. There are also clips around the edge of the case you will need to prize open, using, for example, a plastic card.
Main PCB:
https://fccid.io/TE7EC330G5U/Internal-Photos/10-Internal-Photos-4120425
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port on TP-Link EC330-G5u v1:
V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | J2 | +--- Don't connect
Device has many big holes in the bottom of the case. This allows you connect Serial Port even without the case opening.
| Serial connection parameters for TP-Link EC330-G5u v1 | 115200, 8N1, 3.3V |
|---|
JTAG
Not supported.
→ port.jtag general information about the JTAG port, JTAG cable, etc.
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 40] Device found in MTK table, ID: c8d1, EXT_ID: 809540 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 . partable is: uboot:0x400000@0x0 os0:0x3000000@0x400000 os1:0x3000000@0x3400000 userfs:0x1000000@0x6400000 ubootenv:0x400000@0x7400000 factory:0x400000@0x7800000 .============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Dec 29 2018 Time:11:24:16 ============================================ THIS IS Main Uboot: Including recovery webserver. icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes set LAN/WAN WLLLL this uboot is loaded from 0xbc020000 Press '4' or 't' to break the booting process Press 'x' to enter recovery web server 0 3: System Boot system code via Flash. do_bootm ## Booting image at bc400000 ... Image Name: OS IMAGE Image Type: MIPS Linux Firmware (uncompressed) Data Size: 18218944 Bytes = 17.4 MB Load Address: a0200000 Entry Point: a0200000 ret is -3 try next header ## Booting image at bc400040 ... Image Name: NAND Flash I Image Type: MIPS Linux Standalone Program (uncompressed) Data Size: 180596 Bytes = 176.4 kB Load Address: a01fb040 Entry Point: a0200000 ... Verifying Checksum ... OK data copied to 0xa01fb040 OK jump to memory 0xa0200000 U-Boot 1.1.3 (Oct 16 2019 - 08:14:45) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f88000 Config XHCI 40M PLL #Reset_MT7530 Allocate 16 byte aligned buffer: 87fc7470 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 40] Device found in MTK table, ID: c8d1, EXT_ID: 809540 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 . partable is: uboot:0x400000@0x0 os0:0x3000000@0x400000 os1:0x3000000@0x3400000 userfs:0x1000000@0x6400000 ubootenv:0x400000@0x7400000 factory:0x400000@0x7800000 .============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Oct 16 2019 Time:08:14:45 ============================================ THIS IS Image Uboot: Uboot included in upgrade image. icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes set LAN/WAN WLLLL this uboot is loaded from 0xbc400040 Press '2' or 't' to break the booting process Press 'x' to enter recovery web server 0 3: System Boot system code via Flash. check image0 check image header magic ==>OK check image header crc ==>OK check image1 check image header magic ==>OK check image header crc ==>OK ================================================= The boot image is Image0 check image content crc ==>......................................................................................................................................................................................................................................................................................OK ================================================= ================================================= ================================================= ## Booting image at bc440000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3431340 Bytes = 3.3 MB Load Address: 81001000 Entry Point: 8161bfe0 ..................................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8161bfe0) ... ## Giving linux memsize in MB, 128 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 [ 0.000000] Linux version 3.10.14 (compile@c6459b075f9a) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Wed Oct 16 08:19:35 UTC 2019 [ 0.000000] [ 0.000000] The CPU feqenuce set to 880 MHz [ 0.000000] GCMP present [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00000000-0x00ffffff] [ 0.000000] Normal [mem 0x01000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @81aa7000 s6784 r8192 d13696 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00062005 [ 0.000000] Readback ErrCtl register=00062005 [ 0.000000] Memory: 119940k/131072k available (6291k kernel code, 11132k reserved, 2533k data, 256k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.096000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) [ 0.128000] pid_max: default: 32768 minimum: 301 [ 0.132000] Mount-cache hash table entries: 512 [ 0.136000] launch: starting cpu1 [ 0.140000] launch: cpu1 gone! [ 0.140000] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.140000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.140000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.140000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.172000] Synchronize counters for CPU 1: done. [ 0.176000] launch: starting cpu2 [ 0.180000] launch: cpu2 gone! [ 0.180000] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.180000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.180000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.180000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.212000] Synchronize counters for CPU 2: done. [ 0.216000] launch: starting cpu3 [ 0.220000] launch: cpu3 gone! [ 0.220000] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.220000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.220000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.220000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.248000] Synchronize counters for CPU 3: done. [ 0.252000] Brought up 4 CPUs [ 0.256000] devtmpfs: initialized [ 0.260000] NET: Registered protocol family 16 [ 0.564000] release PCIe RST: RALINK_RSTCTRL = 7000000 [ 0.568000] PCIE PHY initialize [ 0.572000] ***** Xtal 40MHz ***** [ 0.572000] start MT7621 PCIe register access [ 1.172000] RALINK_RSTCTRL = 7000000 [ 1.172000] RALINK_CLKCFG1 = 77ffeff8 [ 1.176000] [ 1.176000] *************** MT7621 PCIe RC mode ************* [ 1.680000] PCIE2 no card, disable it(RST&CLK) [ 1.684000] pcie_link status = 0x3 [ 1.688000] RALINK_RSTCTRL= 3000000 [ 1.688000] *** Configure Device number setting of Virtual PCI-PCI bridge *** [ 1.696000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 [ 1.704000] PCIE0 enabled [ 1.704000] PCIE1 enabled [ 1.708000] interrupt enable status: 300000 [ 1.712000] Port 1 N_FTS = 1b105000 [ 1.716000] Port 0 N_FTS = 1b105000 [ 1.720000] config reg done [ 1.720000] init_rt2880pci done [ 1.748000] bio: create slab <bio-0> at 0 [ 1.752000] vgaarb: loaded [ 1.756000] SCSI subsystem initialized [ 1.760000] PCI host bridge to bus 0000:00 [ 1.764000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.772000] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.780000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.788000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.796000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.804000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.808000] pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) [ 1.812000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.816000] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] [ 1.820000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] [ 1.824000] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] [ 1.828000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 1.832000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.836000] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.840000] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] [ 1.844000] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.848000] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] [ 1.852000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) [ 1.856000] PCI: Enabling device 0000:00:01.0 (0004 -> 0006) [ 1.860000] BAR0 at slot 0 = 0 [ 1.860000] bus=0x0, slot = 0x0 [ 1.864000] res[0]->start = 0 [ 1.864000] res[0]->end = 0 [ 1.868000] res[1]->start = 60200000 [ 1.868000] res[1]->end = 6020ffff [ 1.872000] res[2]->start = 0 [ 1.872000] res[2]->end = 0 [ 1.876000] res[3]->start = 0 [ 1.876000] res[3]->end = 0 [ 1.880000] res[4]->start = 0 [ 1.880000] res[4]->end = 0 [ 1.884000] res[5]->start = 0 [ 1.884000] res[5]->end = 0 [ 1.888000] BAR0 at slot 1 = 0 [ 1.888000] bus=0x0, slot = 0x1 [ 1.892000] res[0]->start = 0 [ 1.892000] res[0]->end = 0 [ 1.896000] res[1]->start = 60210000 [ 1.896000] res[1]->end = 6021ffff [ 1.900000] res[2]->start = 0 [ 1.900000] res[2]->end = 0 [ 1.904000] res[3]->start = 0 [ 1.904000] res[3]->end = 0 [ 1.908000] res[4]->start = 0 [ 1.908000] res[4]->end = 0 [ 1.912000] res[5]->start = 0 [ 1.912000] res[5]->end = 0 [ 1.916000] bus=0x1, slot = 0x0, irq=0x4 [ 1.916000] res[0]->start = 60000000 [ 1.920000] res[0]->end = 600fffff [ 1.920000] res[1]->start = 0 [ 1.924000] res[1]->end = 0 [ 1.924000] res[2]->start = 0 [ 1.928000] res[2]->end = 0 [ 1.928000] res[3]->start = 0 [ 1.932000] res[3]->end = 0 [ 1.932000] res[4]->start = 0 [ 1.936000] res[4]->end = 0 [ 1.936000] res[5]->start = 0 [ 1.940000] res[5]->end = 0 [ 1.940000] bus=0x2, slot = 0x1, irq=0x18 [ 1.944000] res[0]->start = 60100000 [ 1.944000] res[0]->end = 601fffff [ 1.948000] res[1]->start = 0 [ 1.948000] res[1]->end = 0 [ 1.952000] res[2]->start = 0 [ 1.952000] res[2]->end = 0 [ 1.956000] res[3]->start = 0 [ 1.956000] res[3]->end = 0 [ 1.960000] res[4]->start = 0 [ 1.960000] res[4]->end = 0 [ 1.964000] res[5]->start = 0 [ 1.964000] res[5]->end = 0 [ 1.968000] Switching to clocksource Ralink Systick timer [ 1.972000] NET: Registered protocol family 2 [ 1.976000] Clockevents: could not switch to one-shot mode: [ 1.976000] Clockevents: could not switch to one-shot mode: [ 1.976000] Clockevents: could not switch to one-shot mode: [ 1.976000] MIPS is not functional. [ 1.976000] MIPS is not functional. [ 1.976000] Clockevents: could not switch to one-shot mode: MIPS is not functional. [ 1.976000] Could not switch to high resolution mode on CPU 1 [ 1.976000] Could not switch to high resolution mode on CPU 3 [ 1.976000] Could not switch to high resolution mode on CPU 2 [ 1.976000] MIPS is not functional. [ 2.028000] Could not switch to high resolution mode on CPU 0 [ 2.036000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 2.044000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 2.048000] TCP: Hash tables configured (established 1024 bind 1024) [ 2.056000] TCP: reno registered [ 2.060000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.064000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.072000] NET: Registered protocol family 1 [ 2.080000] exFAT: Version 1.2.9 [ 2.080000] fuse init (API version 7.22) [ 2.088000] msgmni has been set to 234 [ 2.092000] io scheduler noop registered (default) [ 2.096000] reg_int_mask=0, INT_MASK= 0 [ 2.100000] HSDMA_init [ 2.104000] [ 2.104000] hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 [ 2.112000] [ 2.112000] hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 [ 2.120000] TX_CTX_IDX0 = 0 [ 2.124000] TX_DTX_IDX0 = 0 [ 2.124000] RX_CRX_IDX0 = 3ff [ 2.128000] RX_DRX_IDX0 = 0 [ 2.132000] set_fe_HSDMA_glo_cfg [ 2.136000] HSDMA_GLO_CFG = 465 [ 2.248000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.252000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A [ 2.260000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A [ 2.276000] brd: module loaded [ 2.284000] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error [ 2.288000] Allocate 16 byte aligned buffer: 818f80f0 [ 2.296000] Enable NFI Clock [ 2.296000] # MTK NAND # : Use HW ECC [ 2.300000] NAND ID [C8 D1 80 95 40, 00809540] [ 2.304000] Device found in MTK table, ID: c8d1, EXT_ID: 809540 [ 2.312000] Support this Device in MTK table! c8d1 [ 2.316000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 2.328000] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 [ 2.336000] Scanning device for bad blocks [ 2.484000] Signature matched and data read! [ 2.488000] load_fact_bbt success 1023 [ 2.492000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.500000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.512000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.520000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.532000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.540000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.552000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.560000] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 2.572000] mtd: MT7621-NAND: partitioning exceeds flash size, truncating [ 2.576000] 8 cmdlinepart partitions found on MTD device MT7621-NAND [ 2.584000] Creating 8 MTD partitions on "MT7621-NAND": [ 2.588000] 0x000000000000-0x000000400000 : "uboot" [ 2.596000] 0x000000400000-0x000003400000 : "os0" [ 2.616000] 0x000003400000-0x000006400000 : "os1" [ 2.632000] 0x000006400000-0x000007400000 : "userfs" [ 2.644000] 0x000007400000-0x000007800000 : "ubootenv" [ 2.652000] 0x000007800000-0x000007c00000 : "factory" [ 2.660000] 0x000000000000-0x000007f80000 : "wholeflash" [ 2.700000] 0x000000400000-0x000003400000 : "rootfs" [ 2.720000] OK [ 2.720000] [mtk_nand] probe successfully! [ 2.728000] PPP generic driver version 2.4.2 [ 2.732000] PPP BSD Compression module registered [ 2.736000] PPP MPPE Compression module registered [ 2.740000] NET: Registered protocol family 24 [ 2.744000] register mt_drv [ 2.756000] [ 2.756000] [ 2.756000] === pAd = c0181000, size = 3711072 === [ 2.756000] [ 2.768000] <-- RTMPAllocAdapterBlock, Status=0 [ 2.772000] pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! [ 2.780000] RTMPInitPCIeDevice():device_id=0x7615 [ 2.784000] DriverOwn()::Try to Clear FW Own... [ 3.084000] DriverOwn()::Success to clear FW Own [ 3.092000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 [ 3.096000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 [ 3.104000] RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 [ 3.108000] mt7615_init()--> [ 3.112000] Use 1st iPAiLNA default bin. [ 3.116000] Use 0st /etc/MT7615E_EEPROM1.bin default bin. [ 3.120000] <--mt7615_init() [ 3.124000] ChipOpsMCUHook [ 3.132000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 3.140000] cut_through_token_list_init(): 87762688,87762688 [ 3.148000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 3.156000] cut_through_token_list_init(): 87762698,87762698 [ 3.160000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 3.176000] [ 3.176000] [ 3.176000] === pAd = c0681000, size = 3711072 === [ 3.176000] [ 3.188000] <-- RTMPAllocAdapterBlock, Status=0 [ 3.192000] pAd->PciHif.CSRBaseAddress =0xc0580000, csr_addr=0xc0580000! [ 3.200000] RTMPInitPCIeDevice():device_id=0x7615 [ 3.204000] DriverOwn()::Try to Clear FW Own... [ 3.504000] DriverOwn()::Success to clear FW Own [ 3.508000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 [ 3.516000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 [ 3.520000] RtmpChipOpsHook(492): Not support for HIF_MT yet! MACVersion=0x0 [ 3.528000] mt7615_init()--> [ 3.532000] Use 2nd ePAeLNA default bin. [ 3.536000] Use 1st /etc/MT7615E_EEPROM2.bin default bin. [ 3.540000] <--mt7615_init() [ 3.544000] ChipOpsMCUHook [ 3.552000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 3.560000] cut_through_token_list_init(): 86cc2c08,86cc2c08 [ 3.564000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 3.572000] cut_through_token_list_init(): 86cc2c18,86cc2c18 [ 3.580000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 3.584000] rdm_major = 253 [ 3.588000] Mirror/redirect action on [ 3.592000] u32 classifier [ 3.596000] Performance counters on [ 3.600000] input device check on [ 3.604000] Actions configured [ 3.604000] Netfilter messages via NETLINK v0.30. [ 3.612000] nf_conntrack version 0.5.0 (1874 buckets, 7496 max) [ 3.616000] gre: GRE over IPv4 demultiplexor driver [ 3.620000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.628000] Type=Linux [ 3.628000] TCP: cubic registered [ 3.632000] NET: Registered protocol family 10 [ 3.640000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.644000] sit: IPv6 over IPv4 tunneling driver [ 3.652000] NET: Registered protocol family 17 [ 3.656000] Bridge firewalling registered [ 3.660000] Ebtables v2.0 registered [ 3.664000] 8021q: 802.1Q VLAN Support v1.8 [ 3.672000] UBI: attaching mtd7 to ubi0 [ 3.676000] UBI: MTD device 7 is write-protected, attach in read-only mode [ 4.000000] UBI: scanning is finished [ 4.016000] UBI: attached mtd7 (name "rootfs", size 48 MiB) to ubi0 [ 4.024000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.032000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.036000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.044000] UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0 [ 4.048000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.056000] UBI: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 785299021 [ 4.064000] UBI: available PEBs: 252, total reserved PEBs: 132, PEBs reserved for bad PEB handling: 20 [ 4.076000] UBI: background thread "ubi_bgt0d" started, PID 790 [ 8.116000] UBIFS: read-only UBI device [ 8.120000] UBIFS: static UBI volume - read-only mode [ 8.272000] UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode [ 8.276000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 8.288000] UBIFS: FS size: 12443648 bytes (11 MiB, 98 LEBs), journal size 6475776 bytes (6 MiB, 51 LEBs) [ 8.296000] UBIFS: reserved for root: 0 bytes (0 KiB) [ 8.300000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 9EA1D9E7-A9EB-4401-9F2F-B222CF71B963, small LPT model [ 8.316000] VFS: Mounted root (ubifs filesystem) readonly on device 0:11. [ 8.324000] devtmpfs: mounted [ 8.328000] Freeing unused kernel memory: 256K (818a0000 - 818e0000) starting pid 792, tty '': '/etc/init.d/rcS' [ 8.488000] gpioctrl: module license 'unspecified' taints kernel. [ 8.496000] Disabling lock debugging due to kernel taint [ 8.512000] Ralink gpio driver initialized [ 8.688000] UBI: attaching mtd3 to ubi1 [ 8.844000] UBI: scanning is finished [ 8.864000] UBI: attached mtd3 (name "userfs", size 16 MiB) to ubi1 [ 8.872000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 8.876000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 8.884000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 8.892000] UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0 [ 8.896000] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 8.904000] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1035386040 [ 8.912000] UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB handling: 20 [ 8.924000] UBI: background thread "ubi_bgt1d" started, PID 802 UBI device number 1, total 128 LEBs (16252928 bytes, 15.5 MiB), [ 8.936000] UBIFS: background thread "ubifs_bgt1_0" started, PID 805 available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [ 9.008000] UBIFS: recovery needed [ 9.104000] ..[ 9.188000] UBIFS: recovery completed .[ 9.192000] UBIFS: mounted UBI device 1, volume 0, name "userfs" [ 9.196000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.208000] UBIFS: FS size: 11935744 bytes (11 MiB, 94 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 9.216000] UBIFS: reserved for root: 563754 bytes (550 KiB) [ 9.220000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID C03CF46B-375A-4AFB-B32E-F1F36DD48B14, small LPT model cp: can't stat '/etc/SingleSKU_FCC.dat': No such file or directory [ 9.352000] usbcore: registered new interface driver usbfs [ 9.360000] usbcore: registered new interface driver hub [ 9.364000] usbcore: registered new device driver usb [ 9.412000] *****run project phy. [ 9.424000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.436000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.448000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.460000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.472000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.484000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.496000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.508000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.520000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.532000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.560000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.572000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.584000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.596000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.608000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.620000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.632000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.644000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.656000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.668000] FM_OUT value: u4FmOut = 0(0x00000000) [ 9.792000] xhci-hcd xhci-hcd: xHCI Host Controller [ 9.796000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 [ 9.804000] xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 [ 9.812000] hub 1-0:1.0: USB hub found [ 9.816000] hub 1-0:1.0: 2 ports detected [ 9.820000] xhci-hcd xhci-hcd: xHCI Host Controller [ 9.824000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 [ 9.832000] hub 2-0:1.0: USB hub found [ 9.836000] hub 2-0:1.0: 1 port detected [ 9.860000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.872000] ehci-platform: EHCI generic platform driver [ 9.892000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 9.924000] usbcore: registered new interface driver usb-storage [ 9.964000] add domain:tplinkwifi.net [ 9.968000] add domain:tplinkap.net [ 9.972000] add domain:tplinklogin.net [ 9.976000] tp_domain init ok [ 9.996000] PPTP driver version 0.8.5 [ 10.008000] l2tp_core: L2TP core driver, V2.0 [ 10.024000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 Please press Enter to activate this console. [ dm_init ] 1696: load dm [ dm_init ] 1699: load dm config [ dm_loadCfg ] 3307: read out cfg is <?xml version="1.0"?> <DslCpeConfig> <InternetGatewayDevice> <DeviceSummary val="InternetGatewayDevice:1.1[](Baseline:1, EthernetLAN:1)" /> <LANDeviceNumberOfEntries val=1 /> <DeviceInfo> <ManufacturerOUI val=68FF7B /> [ dm_init ] 1703: load device config [ dm_loadFlashCfgFromFlash ] 2792: software version is not match, in config, version = 4294967295 [ dm_loadFlashCfgFromFlash ] 2792: ret = 9802, return [ dm_loadFlashCfg ] 2990: Read user config from flash partition device-config failed. Now read default config /etc/dev_config.xml [ dm_readFile ] 2204: can not open xml file /etc/dev_config.xml! [ dm_loadFlashCfgFromFile ] 2920: read default config /etc/dev_config.xml failed [ dm_loadFlashCfgFromFile ] 2920: ret = 9801, return [ dm_loadFlashCfg ] 2992: Read default config /etc/dev_config.xml failed [ dm_init ] 1707: load factory config [ getSubMtdPartition ] 1071: sub mtd factory-config is map to factory [ checkSubMtd ] 578: Random write not supported. But We can try reading the whole data out first and then write. [ getSubMtdPartition ] 1071: sub mtd factory-config is map to factory [ checkSubMtd ] 578: Random write not supported. But We can try reading the whole data out first and then write. [ cos_init ] 374: is router mode [ initFuncTable ] 1090: ===>Enter router mode [ oal_getUpgradeStatusFromFlash ] 883: upgrade status is 0 [ rsl_getManagementServerObj ] 568: cannot set connectionRequestURL yet because no WAN intf is up [ rsl_getManagementServerObj ] 568: cannot set connectionRequestURL yet because no WAN intf is up [ rsl_getManagementServerObj ] 568: cannot set connectionRequestURL yet because no WAN intf is up [ 11.436000] GMAC1_MAC_ADRH -- : 0x0000000c [ 11.440000] GMAC1_MAC_ADRL -- : 0x432880f7 [ 11.444000] Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! [ 11.452000] GMAC1_MAC_ADRH -- : 0x0000000c [ 11.456000] GMAC1_MAC_ADRL -- : 0x4328808f [ 11.464000] PROC INIT OK! [ 11.476000] 5:FFFFFF86:FFFFFF80:FFFFFFD4:20:FFFFFFC1 [ 11.480000] Raeth v3.1 (Tasklet) [ 11.488000] set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 [ 11.492000] [ 11.492000] phy_tx_ring = 0x00cac000, tx_ring = 0xa0cac000 [ 11.516000] phy_free_head is 0xcb0000!!! [ 11.520000] phy_free_tail_phy is 0xcb7ff0!!! [ 11.524000] txd_pool=a0cb8000 phy_txd_pool=00CB8000 [ 11.528000] ei_local->free_skb start address is 0x86058454. [ 11.536000] free_txd: 00cb8010, ei_local->cpu_ptr: 00CB8000 [ 11.540000] POOL HEAD_PTR | DMA_PTR | CPU_PTR [ 11.544000] ----------------+---------+-------- [ 11.548000] 0xa0cb8000 0x00CB8000 0x00CB8000 [ 11.552000] [ 11.552000] phy_qrx_ring = 0x00cc0000, qrx_ring = 0xa0cc0000 [ 11.564000] [ 11.564000] phy_rx_ring0 = 0x00cc4000, rx_ring[0] = 0xa0cc4000 [ 11.592000] MT7530 Reset Completed!! [ 11.600000] change HW-TRAP to 0x117c8f [ 11.608000] GMAC1_MAC_ADRH -- : 0x000068ff [ 11.612000] GMAC1_MAC_ADRL -- : 0x7b2b37f4 [ 11.616000] GDMA2_MAC_ADRH -- : 0x0000000c [ 11.620000] GDMA2_MAC_ADRL -- : 0x432880a8 [ 11.628000] eth1: ===> VirtualIF_open [ 11.632000] MT7621 GE2 link rate to 1G [ 11.632000] CDMA_CSG_CFG = 81000000 [ 11.632000] GDMA1_FWD_CFG = 20710000 [ 11.632000] GDMA2_FWD_CFG = 20710000 [ 11.652000] GDMA2_MAC_ADRH -- : 0x000068ff [ 11.656000] GDMA2_MAC_ADRL -- : 0x7b2b37f5 [ 11.660000] eth1: ===> VirtualIF_open ioctl: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] set if eth0.3 to *not wan dev set if eth0.4 to *not wan dev set if eth0.5 to *not wan dev set if eth0.6 to *not wan dev set if eth1.2 to wan dev brctl: bridge br0: Invalid argument [ 11.880000] device eth0.3 entered promiscuous mode [ 11.888000] device eth0 entered promiscuous mode [ 11.892000] br0: port 1(eth0.3) entered forwarding state [ 11.896000] br0: port 1(eth0.3) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 brctl: bridge br0: Invalid argument [ 11.944000] device eth0.4 entered promiscuous mode [ 11.952000] br0: port 2(eth0.4) entered forwarding state [ 11.956000] br0: port 2(eth0.4) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] [ 11.968000] br0: port 2(eth0.4) entered disabled state 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 brctl: bridge br0: Invalid argument [ 12.008000] device eth0.5 entered promiscuous mode [ 12.016000] br0: port 3(eth0.5) entered forwarding state [ 12.020000] br0: port 3(eth0.5) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnu[ 12.036000] br0: port 3(eth0.5) entered disabled state sedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 brctl: bridge br0: Invalid argument [ 12.072000] device eth0.6 entered promiscuous mode [ 12.080000] br0: port 4(eth0.6) entered forwarding state [ 12.084000] br0: port 4(eth0.6) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN[ 12.104000] br0: port 4(eth0.6) entered disabled state TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 Interface doesn't accept private ioctl... set (8BE2): Network is down [ 12.236000] DriverOwn()::Return since already in Driver Own... [ 12.244000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860_5G.dat [ 12.252000] Open file "/etc/Wireless/RT2860/RT2860_5G.dat" failed! [ 12.260000] E2pAccessMode=2 [ 12.260000] SSID[0]=TP-Link_0969, EdcaIdx=0 [ 12.268000] SSID[1]=TP-Link_0969_0, EdcaIdx=0 [ 12.272000] SSID[2]=TP-Link_0969_1, EdcaIdx=0 [ 12.276000] SSID[3]=TP-Link_0969_2, EdcaIdx=0 [ 12.280000] SSID[4]=TP-Link_0969_3, EdcaIdx=0 [ 12.284000] cfg_mode=9 [ 12.288000] cfg_mode=9 [ 12.288000] wmode_band_equal(): Band Equal! [ 12.296000] BandSteering=0 [ 12.296000] BndStrgBssIdx=1;0;0;0;0 [ 12.300000] [TxPower] BAND0: 100 [ 12.304000] [PERCENTAGEenable] BAND0: 0 [ 12.308000] APEdca0 [ 12.312000] APEdca1 [ 12.312000] APEdca2 [ 12.316000] APEdca3 [ 12.320000] APSDCapable[0]=0 [ 12.324000] APSDCapable[1]=0 [ 12.328000] APSDCapable[2]=0 [ 12.332000] APSDCapable[3]=0 [ 12.332000] APSDCapable[4]=0 [ 12.336000] APSDCapable[5]=0 [ 12.340000] APSDCapable[6]=0 [ 12.340000] APSDCapable[7]=0 [ 12.344000] APSDCapable[8]=0 [ 12.348000] APSDCapable[9]=0 [ 12.352000] APSDCapable[10]=0 [ 12.352000] APSDCapable[11]=0 [ 12.356000] APSDCapable[12]=0 [ 12.360000] APSDCapable[13]=0 [ 12.364000] APSDCapable[14]=0 [ 12.364000] APSDCapable[15]=0 [ 12.368000] default ApCliAPSDCapable[0]=0 [ 12.372000] default ApCliAPSDCapable[1]=0 [ 12.376000] DfsZeroWait Support=0/0 [ 12.380000] DfsZeroWaitCacTime=255/255 [ 12.400000] AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 12.412000] HT: WDEV[0] Ext Channel = ABOVE [ 12.416000] HT: greenap_cap = 0 [ 12.436000] WtcSetMaxStaNum: MaxStaNum:87, BssidNum:5, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:121 [ 12.448000] Top Init Done! [ 12.452000] Use alloc_skb [ 12.452000] RX[0] DESC a0c14000 size = 16384 [ 12.460000] RX[1] DESC a0c12000 size = 8192 [ 12.464000] Hif Init Done! [ 12.468000] ctl->txq = c0506030 [ 12.472000] ctl->rxq = c050603c [ 12.476000] ctl->ackq = c0506048 [ 12.476000] ctl->kickq = c0506054 [ 12.480000] ctl->tx_doneq = c0506060 [ 12.484000] ctl->rx_doneq = c050606c [ 12.488000] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) [ 12.496000] mt7615_fw_prepare(2689): MT7615_E3, USE E3 patch and ram code binary image [ 12.504000] AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(11102) [ 12.508000] AndesRestartCheck: Current TOP_MISC2(0x1) [ 12.516000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) [ 12.520000] 20170809192718a [ 12.524000] [ 12.528000] platform = [ 12.528000] ALPS [ 12.532000] hw/sw version = [ 12.532000] 8a108a10 [ 12.536000] patch version = [ 12.540000] 00000010 [ 12.540000] Patch SEM Status=2 [ 12.544000] MtCmdPatchSemGet:(ret = 0) [ 12.548000] [ 12.548000] Patch is not ready && get semaphore success, SemStatus(2) [ 12.556000] EventGenericEventHandler: CMD Success [ 12.560000] MtCmdAddressLenReq:(ret = 0) [ 12.564000] MtCmdPatchFinishReq [ 12.580000] EventGenericEventHandler: CMD Success [ 12.584000] Send checksum req.. [ 12.588000] Patch SEM Status=3 [ 12.588000] MtCmdPatchSemGet:(ret = 0) [ 12.592000] [ 12.592000] Release patch semaphore, SemStatus(3) [ 12.600000] AndesMTEraseRomPatch [ 12.604000] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 [ 12.608000] AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(462248) [ 12.616000] Build Date:_201708190346 [ 12.620000] Build Date:_201708190346 [ 12.624000] AndesRestartCheck: Current TOP_MISC2(0x1) [ 12.628000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) [ 12.636000] EventGenericEventHandler: CMD Success [ 12.640000] MtCmdAddressLenReq:(ret = 0) [ 12.648000] EventGenericEventHandler: CMD Success [ 12.652000] MtCmdAddressLenReq:(ret = 0) [ 12.656000] MtCmdFwStartReq: override = 1, address = 540672 [ 12.664000] EventGenericEventHandler: CMD Success [ 12.668000] Build Date:_201707211524 [ 12.672000] EventGenericEventHandler: CMD Success [ 12.676000] MtCmdAddressLenReq:(ret = 0) [ 12.680000] MtCmdFwStartReq: override = 4, address = 0 [ 12.740000] EventGenericEventHandler: CMD Success [ 12.792000] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 [ 12.796000] MCU Init Done! [ 12.800000] efuse_probe: efuse = 10000212 [ 12.804000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 12.808000] RtmpEepromGetDefault::e2p_dafault=1 [ 12.812000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 12.820000] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] [ 12.828000] sub mtd radio is map to factory [ 12.832000] Random write not supported. But We can try reading the whole data out first and then write. [ 12.840000] read radio success, offset 0x0, size 0x400 [ 12.844000] sub mtd radio is map to factory [ 12.852000] Random write not supported. But We can try reading the whole data out first and then write. [ 12.860000] read radio success, offset 0x400, size 0x2400 [ 12.868000] sub mtd radio is map to factory [ 12.872000] Random write not supported. But We can try reading the whole data out first and then write. [ 12.884000] read radio success, offset 0x2600, size 0x2400 [ 12.888000] sub mtd radio is map to factory [ 12.896000] Random write not supported. But We can try reading the whole data out first and then write. [ 12.908000] read radio success, offset 0x4460, size 0x2400 [ 12.912000] NICReadEEPROMParameters: EEPROM 0x52 b306 [ 12.920000] sub mtd radio is map to factory [ 12.924000] Random write not supported. But We can try reading the whole data out first and then write. [ 12.936000] read radio success, offset 0x4da8, size 0x4000 [ 12.944000] MtCmdSetTxLpfCal:(ret = 0) [ 12.948000] MtCmdSetTxIqCal:(ret = 0) [ 12.952000] MtCmdSetTxDcCal:(ret = 0) [ 12.956000] MtCmdSetRxFiCal:(ret = 0) [ 12.956000] MtCmdSetRxFdCal:(ret = 0) [ 12.960000] MtCmdSetRxFdCal:(ret = 0) [ 12.964000] MtCmdSetRxFdCal:(ret = 0) [ 12.968000] MtCmdSetRxFdCal:(ret = 0) [ 12.972000] MtCmdSetRxFdCal:(ret = 0) [ 12.976000] MtCmdSetRxFdCal:(ret = 0) [ 12.980000] MtCmdSetRxFdCal:(ret = 0) [ 12.984000] MtCmdSetRxFdCal:(ret = 0) [ 12.988000] MtCmdSetRxFdCal:(ret = 0) [ 12.992000] NICReadEEPROMParameters: EEPROM 0x52 b306 [ 13.536000] Country Region from e2p = 101 [ 13.540000] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 [ 13.548000] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 [ 13.556000] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 [ 13.560000] rtmp_read_txpwr_from_eeprom(233): Don't Support this now! [ 13.568000] RTMPReadTxPwrPerRate(1381): Don't Support this now! [ 13.572000] RcRadioInit(): DbdcMode=0, ConcurrentBand=1 [ 13.580000] RcRadioInit(): pRadioCtrl=87763458,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 13.588000] MtCmdSetDbdcCtrl:(ret = 0) [ 13.592000] Band Rf: 1, Phy Mode: 2 [ 13.596000] AntCfgInit(2766): Not support for HIF_MT yet! [ 13.600000] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! [ 13.608000] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! [ 13.612000] EEPROM Init Done! [ 13.616000] mt_mac_init()--> [ 13.620000] mt_mac_pse_init(2750): Don't Support this now! [ 13.624000] mt7615_init_mac_cr()--> [ 13.628000] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c [ 13.632000] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c [ 13.640000] MtAsicSetMacMaxLen(1300): Not finish Yet! [ 13.644000] <--mt_mac_init() [ 13.648000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 13.656000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 13.664000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 13.668000] MAC Init Done! [ 13.672000] MT7615BBPInit():BBP Initialization..... [ 13.676000] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 [ 13.688000] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 [ 13.696000] MT7615BBPInit() todo [ 13.700000] PHY Init Done! [ 13.704000] tx_pwr_comp_init():NotSupportYet! [ 13.708000] MtCmdSetMacTxRx:(ret = 0) [ 13.712000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 13.720000] ApAutoChannelAtBootUp-----------------> [ 13.724000] ApAutoChannelAtBootUp: AutoChannelBootup = 1, AutoChannelFlag = 1 [ 13.732000] MtCmdSetMacTxRx:(ret = 0) [ 13.736000] mt7615_apply_dcoc() : reload Central CH [2] BW [0] from cetral freq [2417] offset [2200] [ 13.744000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 13.748000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 13.760000] MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 [ 13.768000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 13.984000] mt7615_apply_dcoc() : reload Central CH [3] BW [0] from cetral freq [2417] offset [2200] [ 13.992000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 13.996000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 14.004000] MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 14.012000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 14.228000] mt7615_apply_dcoc() : reload Central CH [4] BW [0] from cetral freq [2432] offset [2300] [ 14.236000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 14.240000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 14.248000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 [ 14.256000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 14.472000] mt7615_apply_dcoc() : reload Central CH [5] BW [0] from cetral freq [2432] offset [2300] [ 14.480000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 14.484000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 14.492000] MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 [ 14.500000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 14.716000] mt7615_apply_dcoc() : reload Central CH [6] BW [0] from cetral freq [2432] offset [2300] [ 14.724000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 14.728000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 14.736000] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 14.744000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 14.960000] mt7615_apply_dcoc() : reload Central CH [7] BW [0] from cetral freq [2447] offset [2400] [ 14.968000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 14.972000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 14.980000] MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 [ 14.988000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 15.204000] mt7615_apply_dcoc() : reload Central CH [8] BW [0] from cetral freq [2447] offset [2400] [ 15.212000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 15.216000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 15.224000] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 [ 15.232000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 15.448000] mt7615_apply_dcoc() : reload Central CH [9] BW [0] from cetral freq [2447] offset [2400] [ 15.456000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 15.460000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 15.468000] MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 [ 15.476000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 15.692000] mt7615_apply_dcoc() : reload Central CH [10] BW [0] from cetral freq [2467] offset [2500] [ 15.700000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 15.704000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 15.712000] MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 [ 15.720000] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 15.936000] ==================================================================== [ 15.940000] Channel 2 : Busy Time = 5023, Skip Channel = FALSE, BwCap = TRUE [ 15.948000] Channel 3 : Busy Time = 5336, Skip Channel = FALSE, BwCap = TRUE [ 15.956000] Channel 4 : Busy Time = 2441, Skip Channel = FALSE, BwCap = TRUE [ 15.964000] Channel 5 : Busy Time = 3236, Skip Channel = FALSE, BwCap = TRUE [ 15.972000] Channel 6 : Busy Time = 5993, Skip Channel = FALSE, BwCap = TRUE [ 15.980000] Channel 7 : Busy Time = 2906, Skip Channel = FALSE, BwCap = TRUE [ 15.984000] Channel 8 : Busy Time = 3267, Skip Channel = FALSE, BwCap = TRUE [ 15.992000] Channel 9 : Busy Time = 5927, Skip Channel = FALSE, BwCap = TRUE [ 16.000000] Channel 10 : Busy Time = 11167, Skip Channel = FALSE, BwCap = TRUE [ 16.008000] ==================================================================== [ 16.016000] Rule 3 Channel Busy time value : Select Primary Channel 4 [ 16.020000] Rule 3 Channel Busy time value : Min Channel Busy = 2441 [ 16.028000] Rule 3 Channel Busy time value : BW = 20 [ 16.032000] AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 14,Channel = 4 [ 16.044000] AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 14,Channel = 4 [ 16.052000] AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 14,Channel = 4 [ 16.064000] AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 14,Channel = 4 [ 16.072000] AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 14,Channel = 4 [ 16.084000] ApAutoChannelAtBootUp<----------------- [ 16.088000] WifiSysOpen(), wdev idx = 0 [ 16.092000] wdev_attr_update(): wdevId0 = 68:ff:7b:2b:37:f4 [ 16.096000] MtCmdSetDbdcCtrl:(ret = 0) [ 16.104000] Current Channel is 4. DfsZeroWaitSupport=0 [ 16.108000] MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [ 16.112000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 16.120000] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 [ 16.124000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.132000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 16.144000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 [ 16.144000] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 16.160000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 3 [ 16.288000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 16.292000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 16.300000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 16.304000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 16.312000] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=4, HT-CentCh=6, VHT-CentCh=0 [ 16.320000] mt7615_apply_dcoc() : reload Central CH [6] BW [1] from cetral freq [2432] offset [2300] [ 16.328000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 16.332000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 16.340000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 16.352000] BW = 1,TXStream = 4, RXStream = 4, scan(0) open DNS error: No such file or directory [ oal_sys_getOldTZInfo ] 507: Open TZ file error! [ 16.400000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=4, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1) [ 16.424000] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY [ 16.428000] MtAsicSetRalinkBurstMode(2605): Not support for HIF_MT yet! [ 16.436000] MtAsicSetPiggyBack(777): Not support for HIF_MT yet! [ 16.440000] MtAsicSetTxPreamble(2584): Not support for HIF_MT yet! [ 16.448000] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! [ 16.456000] AndesLedEnhanceOP: Success! [ 16.460000] Main bssid = 68:ff:7b:2b:37:f4 [ 16.464000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 16.468000] MtCmdSetMacTxRx:(ret = 0) [ 16.472000] MCS Set = ff ff ff ff 01 [ 16.476000] <==== mt_wifi_init, Status=0 [ 16.480000] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 [ 16.484000] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 [ 16.508000] wlan_operate_set_vht_bw(): new vht_bw:1 > cap_vht_bw: 0, correct to cap_vht_bw [ 16.520000] WtcSetMaxStaNum: MaxStaNum:87, BssidNum:5, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:121 [ 16.532000] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. [ 16.536000] Correct apidx from 0 to 0 for WscUUIDInit [ 16.540000] Generate UUID for apidx(0) [ 16.604000] WifiSysOpen(), wdev idx = 1 [ 16.608000] wdev_attr_update(): wdevId1 = 6a:ff:7b:1b:37:f4 [ 16.612000] MtCmdSetDbdcCtrl:(ret = 0) [ 16.616000] [PMF]APPMFInit:: apidx=1, MFPC=0, MFPR=0, SHA256=0 [ 16.620000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.632000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.640000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 16.648000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:126 for WDEV_TYPE:1 [ 16.648000] LinkToOmacIdx = 11, LinkToWdevType = 1 [ 16.660000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 16.664000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 3 [ 16.680000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 16.688000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 16.692000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 16.700000] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=4, HT-CentCh=6, VHT-CentCh=0 [ 16.708000] mt7615_apply_dcoc() : reload Central CH [6] BW [1] from cetral freq [2432] offset [2300] [ 16.716000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 16.720000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 16.728000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 16.740000] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 16.756000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=4, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1) [ 16.780000] LeadTimeForBcn, OmacIdx = 11, WDEV_WITH_BCN_ABILITY [ 16.788000] Generate UUID for apidx(1) [ 16.792000] WifiSysOpen(), wdev idx = 2 [ 16.796000] wdev_attr_update(): wdevId2 = 6a:ff:7b:2b:37:f4 wscd: SSDP UDP P[ 16.804000] MtCmdSetDbdcCtrl:(ret = 0) ORT = 1900[ 16.808000] [PMF]APPMFInit:: apidx=2, MFPC=0, MFPR=0, SHA256=0 [ 16.816000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.824000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.832000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 16.840000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 16.848000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:125 for WDEV_TYPE:1 [ 16.848000] LinkToOmacIdx = 12, LinkToWdevType = 1 [ 16.864000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 16.868000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 3 [ 16.884000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 16.888000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 16.896000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 16.900000] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=4, HT-CentCh=6, VHT-CentCh=0 [ 16.908000] mt7615_apply_dcoc() : reload Central CH [6] BW [1] from cetral freq [2432] offset [2300] [ 16.920000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 16.924000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 16.932000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 16.940000] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 16.960000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=4, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1) [ 16.984000] LeadTimeForBcn, OmacIdx = 12, WDEV_WITH_BCN_ABILITY [ 16.988000] Generate UUID for apidx(2) [ 16.996000] WifiSysOpen(), wdev idx = 3 [ 17.000000] wdev_attr_update(): wdevId3 = 6a:ff:7b:3b:37:f4 [ 17.008000] MtCmdSetDbdcCtrl:(ret = 0) [ 17.012000] [PMF]APPMFInit:: apidx=3, MFPC=0, MFPR=0, SHA256=0 [ 17.016000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.024000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.032000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.044000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.052000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 17.060000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:124 for WDEV_TYPE:1 [ 17.060000] LinkToOmacIdx = 13, LinkToWdevType = 1 [ 17.072000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 17.076000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 3 [ 17.092000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 17.100000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 17.104000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 17.112000] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=4, HT-CentCh=6, VHT-CentCh=0 [ 17.120000] mt7615_apply_dcoc() : reload Central CH [6] BW [1] from cetral freq [2432] offset [2300] [ 17.128000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 17.132000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 17.140000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 17.152000] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 17.168000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=4, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1) [ 17.192000] LeadTimeForBcn, OmacIdx = 13, WDEV_WITH_BCN_ABILITY [ 17.200000] Generate UUID for apidx(3) [ 17.204000] WifiSysOpen(), wdev idx = 4 [ 17.208000] wdev_attr_update(): wdevId4 = 6a:ff:7b:4b:37:f4 [ 17.216000] MtCmdSetDbdcCtrl:(ret = 0) [ 17.220000] [PMF]APPMFInit:: apidx=4, MFPC=0, MFPR=0, SHA256=0 [ 17.224000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.236000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.244000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.252000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.260000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:14,Channel=4 [ 17.268000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=14/14, support 13 channels [ 17.276000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:123 for WDEV_TYPE:1 [ 17.276000] LinkToOmacIdx = 14, LinkToWdevType = 1 [ 17.288000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 17.292000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 3 [ 17.308000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 17.316000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 17.324000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 17.328000] mt7615_bbp_adjust():rf_bw=1, ext_ch=1, PrimCh=4, HT-CentCh=6, VHT-CentCh=0 [ 17.336000] mt7615_apply_dcoc() : reload Central CH [6] BW [1] from cetral freq [2432] offset [2300] [ 17.344000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 17.348000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 17.360000] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 17.368000] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 17.384000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 6(Prim=4, HT-CentCh=6, VHT-CentCh=0, BBP_BW=1) [ 17.408000] LeadTimeForBcn, OmacIdx = 14, WDEV_WITH_BCN_ABILITY [ 17.416000] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) [ 17.416000] Generate UUID for apidx(4) [ 17.428000] WifiSysClose(), wdev idx = 1 [ 17.432000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:1b:37:f4), Reason 0x10 [ 17.432000] Beacon lost - AP disabled!!! [ 17.436000] WifiSysGetBssInfoState(): BssInfoIdx 1 not found!!! [ 17.436000] WifiSysUpdateBssInfoState(): BssInfoIdx 1 not found!!! [ 17.464000] BndStrg is already Disable [ 17.472000] WifiSysClose(), wdev idx = 2 [ 17.472000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:2b:37:f4), Reason 0x10 [ 17.472000] Beacon lost - AP disabled!!! [ 17.480000] WifiSysGetBssInfoState(): BssInfoIdx 2 not found!!! [ 17.480000] WifiSysUpdateBssInfoState(): BssInfoIdx 2 not found!!! [ 17.504000] BndStrg is already Disable [ 17.504000] WifiSysClose(), wdev idx = 3 [ 17.516000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:3b:37:f4), Reason 0x10 [ 17.516000] Beacon lost - AP disabled!!! [ 17.524000] WifiSysGetBssInfoState(): BssInfoIdx 3 not found!!! [ 17.524000] WifiSysUpdateBssInfoState(): BssInfoIdx 3 not found!!! [ 17.548000] BndStrg is already Disable [ 17.556000] WifiSysClose(), wdev idx = 4 [ 17.556000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:4b:37:f4), Reason 0x10 [ 17.556000] Beacon lost - AP disabled!!! [ 17.564000] WifiSysGetBssInfoState(): BssInfoIdx 4 not found!!! [ 17.564000] WifiSysUpdateBssInfoState(): BssInfoIdx 4 not found!!! [ 17.592000] BndStrg is already Disable [ 17.592000] [ 17.600000] device ra0 entered promiscuous mode [ 17.604000] br0: port 5(ra0) entered forwarding state [ 17.608000] br0: port 5(ra0) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 [ 17.652000] device apcli0 entered promiscuous mode [ 17.660000] device ra2 entered promiscuous mode [ 17.668000] device ra3 entered promiscuous mode [ 17.676000] device ra4 entered promiscuous mode [ wlan_handleL2Desc ] 1089: br0 [ 17.684000] device ra1 entered promiscuous mode [ 17.696000] is_cali: 1 sh: wlNetlinkTool: not found wscd: SSDP UDP PORT = 1900 Interface doesn't accept private ioctl... set (8BE2): Network is down [ 17.748000] DriverOwn()::Return since already in Driver Own... [ 17.760000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap_5G.dat [ 17.768000] Open file "/etc/Wireless/iNIC/iNIC_ap_5G.dat" failed! [ 17.772000] E2pAccessMode=2 [ 17.776000] SSID[0]=TP-Link_0969_5G, EdcaIdx=0 [ 17.780000] SSID[1]=TP-Link_0969_5G_0, EdcaIdx=0 [ 17.784000] SSID[2]=TP-Link_0969_5G_1, EdcaIdx=0 [ 17.792000] SSID[3]=TP-Link_0969_5G_2, EdcaIdx=0 [ 17.796000] SSID[4]=TP-Link_0969_5G_3, EdcaIdx=0 [ 17.800000] cfg_mode=14 [ 17.804000] cfg_mode=14 [ 17.804000] wmode_band_equal(): Band Equal! [ 17.808000] BandSteering=0 [ 17.812000] BndStrgBssIdx=1;0;0;0;0 [ 17.816000] [TxPower] BAND0: 100 [ 17.820000] [PERCENTAGEenable] BAND0: 0 [ 17.824000] APEdca0 [ 17.828000] APEdca1 [ 17.828000] APEdca2 [ 17.832000] APEdca3 [ 17.836000] APSDCapable[0]=0 [ 17.840000] APSDCapable[1]=0 [ 17.844000] APSDCapable[2]=0 [ 17.848000] APSDCapable[3]=0 [ 17.848000] APSDCapable[4]=0 [ 17.852000] APSDCapable[5]=0 [ 17.856000] APSDCapable[6]=0 [ 17.856000] APSDCapable[7]=0 [ 17.860000] APSDCapable[8]=0 [ 17.864000] APSDCapable[9]=0 [ 17.868000] APSDCapable[10]=0 [ 17.868000] APSDCapable[11]=0 [ 17.872000] APSDCapable[12]=0 [ 17.876000] APSDCapable[13]=0 [ 17.880000] APSDCapable[14]=0 [ 17.880000] APSDCapable[15]=0 [ 17.884000] default ApCliAPSDCapable[0]=0 [ 17.888000] default ApCliAPSDCapable[1]=0 [ 17.892000] DfsZeroWait Support=0/0 [ 17.896000] DfsZeroWaitCacTime=255/255 [ 17.916000] AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 17.928000] HT: WDEV[0] Ext Channel = BELOW [ 17.932000] HT: greenap_cap = 0 [ 17.952000] WtcSetMaxStaNum: MaxStaNum:87, BssidNum:5, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:121 [ 17.964000] Top Init Done! [ 17.968000] Use alloc_skb [ 17.968000] RX[0] DESC a0ca4000 size = 16384 [ 17.976000] RX[1] DESC a0ca2000 size = 8192 [ 17.980000] Hif Init Done! [ 17.984000] ctl->txq = c0a06030 [ 17.988000] ctl->rxq = c0a0603c [ 17.992000] ctl->ackq = c0a06048 [ 17.992000] ctl->kickq = c0a06054 [ 17.996000] ctl->tx_doneq = c0a06060 [ 18.000000] ctl->rx_doneq = c0a0606c [ 18.004000] mt7615_fw_prepare():FW(8a10), HW(8a10), CHIPID(7615)) [ 18.012000] mt7615_fw_prepare(2689): MT7615_E3, USE E3 patch and ram code binary image [ 18.020000] AndesMTLoadRomMethodFwDlRing(1035), cap->rom_patch_len(11102) [ 18.024000] AndesRestartCheck: Current TOP_MISC2(0x1) [ 18.032000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) [ 18.036000] 20170809192718a [ 18.040000] [ 18.044000] platform = [ 18.044000] ALPS [ 18.048000] hw/sw version = [ 18.048000] 8a108a10 [ 18.052000] patch version = [ 18.056000] 00000010 [ 18.056000] Patch SEM Status=2 [ 18.060000] MtCmdPatchSemGet:(ret = 0) [ 18.064000] [ 18.064000] Patch is not ready && get semaphore success, SemStatus(2) [ 18.072000] EventGenericEventHandler: CMD Success [ 18.076000] MtCmdAddressLenReq:(ret = 0) [ 18.080000] MtCmdPatchFinishReq [ 18.096000] EventGenericEventHandler: CMD Success [ 18.100000] Send checksum req.. [ 18.104000] Patch SEM Status=3 [ 18.104000] MtCmdPatchSemGet:(ret = 0) [ 18.108000] [ 18.108000] Release patch semaphore, SemStatus(3) [ 18.116000] AndesMTEraseRomPatch [ 18.120000] WfMcuHwInit: Before NICLoadFirmware, check IcapMode=0 [ 18.124000] AndesMTLoadFwMethodFwDlRing(809), cap->fw_len(462248) [ 18.132000] Build Date:_201708190346 [ 18.136000] Build Date:_201708190346 [ 18.140000] AndesRestartCheck: Current TOP_MISC2(0x1) [ 18.144000] AndesRestartCheck: (TOP_MISC2 = 1), ready to continue...RET(0) [ 18.152000] EventGenericEventHandler: CMD Success [ 18.156000] MtCmdAddressLenReq:(ret = 0) [ 18.164000] EventGenericEventHandler: CMD Success [ 18.168000] MtCmdAddressLenReq:(ret = 0) [ 18.172000] MtCmdFwStartReq: override = 1, address = 540672 [ 18.180000] EventGenericEventHandler: CMD Success [ 18.184000] Build Date:_201707211524 [ 18.188000] EventGenericEventHandler: CMD Success [ 18.192000] MtCmdAddressLenReq:(ret = 0) [ 18.196000] MtCmdFwStartReq: override = 4, address = 0 [ 18.256000] EventGenericEventHandler: CMD Success [ 18.308000] WfMcuHwInit: NICLoadFirmware OK, Check IcapMode=0 [ 18.312000] MCU Init Done! [ 18.316000] efuse_probe: efuse = 10000212 [ 18.320000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 18.324000] RtmpEepromGetDefault::e2p_dafault=1 [ 18.328000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 18.336000] NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0xC000] [ 18.344000] sub mtd radio is map to factory [ 18.348000] Random write not supported. But We can try reading the whole data out first and then write. [ 18.356000] read radio success, offset 0xc000, size 0x400 [ 18.364000] sub mtd radio is map to factory [ 18.368000] Random write not supported. But We can try reading the whole data out first and then write. [ 18.380000] read radio success, offset 0xc400, size 0x2400 [ 18.384000] sub mtd radio is map to factory [ 18.388000] Random write not supported. But We can try reading the whole data out first and then write. [ 18.400000] read radio success, offset 0xe600, size 0x2400 [ 18.408000] sub mtd radio is map to factory [ 18.412000] Random write not supported. But We can try reading the whole data out first and then write. [ 18.424000] read radio success, offset 0x10460, size 0x2400 [ 18.428000] NICReadEEPROMParameters: EEPROM 0x52 b306 [ 18.436000] sub mtd radio is map to factory [ 18.440000] Random write not supported. But We can try reading the whole data out first and then write. [ 18.456000] read radio success, offset 0x10da8, size 0x4000 [ 18.460000] MtCmdSetTxLpfCal:(ret = 0) [ 18.464000] MtCmdSetTxIqCal:(ret = 0) [ 18.468000] MtCmdSetTxDcCal:(ret = 0) [ 18.472000] MtCmdSetRxFiCal:(ret = 0) [ 18.476000] MtCmdSetRxFdCal:(ret = 0) [ 18.480000] MtCmdSetRxFdCal:(ret = 0) [ 18.484000] MtCmdSetRxFdCal:(ret = 0) [ 18.488000] MtCmdSetRxFdCal:(ret = 0) [ 18.492000] MtCmdSetRxFdCal:(ret = 0) [ 18.492000] MtCmdSetRxFdCal:(ret = 0) [ 18.496000] MtCmdSetRxFdCal:(ret = 0) [ 18.500000] MtCmdSetRxFdCal:(ret = 0) [ 18.504000] MtCmdSetRxFdCal:(ret = 0) [ 18.508000] NICReadEEPROMParameters: EEPROM 0x52 b306 [ 19.056000] Country Region from e2p = 101 [ 19.060000] mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 [ 19.064000] mt7615_antenna_default_reset(): DBDC 2G TxPath = 2, 2G RxPath = 2 [ 19.072000] mt7615_antenna_default_reset(): DBDC 5G TxPath = 2, 2G RxPath = 2 [ 19.080000] rtmp_read_txpwr_from_eeprom(233): Don't Support this now! [ 19.088000] RTMPReadTxPwrPerRate(1381): Don't Support this now! [ 19.092000] RcRadioInit(): DbdcMode=0, ConcurrentBand=1 [ 19.096000] RcRadioInit(): pRadioCtrl=86cc3458,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 19.104000] MtCmdSetDbdcCtrl:(ret = 0) [ 19.108000] Band Rf: 1, Phy Mode: 2 [ 19.112000] AntCfgInit(2766): Not support for HIF_MT yet! [ 19.120000] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! [ 19.124000] MtBfBackOffLoadTable: RF_LOCKDOWN Feature OFF !!! [ 19.132000] EEPROM Init Done! [ 19.136000] mt_mac_init()--> [ 19.136000] mt_mac_pse_init(2750): Don't Support this now! [ 19.144000] mt7615_init_mac_cr()--> [ 19.144000] mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c [ 19.152000] mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c [ 19.156000] MtAsicSetMacMaxLen(1300): Not finish Yet! [ 19.160000] <--mt_mac_init() [ 19.164000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 19.172000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 19.176000] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 19.184000] MAC Init Done! [ 19.188000] MT7615BBPInit():BBP Initialization..... [ 19.192000] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 [ 19.200000] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 [ 19.208000] MT7615BBPInit() todo [ 19.212000] PHY Init Done! [ 19.216000] tx_pwr_comp_init():NotSupportYet! [ 19.224000] MtCmdSetMacTxRx:(ret = 0) [ 19.228000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 19.236000] ApAutoChannelAtBootUp-----------------> [ 19.240000] ApAutoChannelAtBootUp: AutoChannelBootup = 1, AutoChannelFlag = 1 [ 19.248000] MtCmdSetMacTxRx:(ret = 0) [ 19.252000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] [ 19.260000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 19.264000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 19.272000] MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 [ 19.284000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 19.496000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] [ 19.504000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 19.508000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 19.516000] MtCmdChannelSwitch: control_chl = 40,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 [ 19.524000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 19.740000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] [ 19.748000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 19.752000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 19.760000] MtCmdChannelSwitch: control_chl = 44,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 [ 19.768000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 19.984000] mt7615_apply_dcoc() : reload Central CH [42] BW [2] from cetral freq [5210] offset [1900] [ 19.992000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 19.996000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 20.004000] MtCmdChannelSwitch: control_chl = 48,control_ch2=0, central_chl = 42 DBDCIdx= 0, Band= 0 [ 20.012000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 20.228000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 20.236000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 20.240000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 20.248000] MtCmdChannelSwitch: control_chl = 149,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 20.256000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 20.472000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 20.480000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 20.484000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 20.492000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 20.500000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 20.716000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 20.724000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 20.728000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 20.736000] MtCmdChannelSwitch: control_chl = 157,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 20.744000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 20.960000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 20.968000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 20.972000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 20.980000] MtCmdChannelSwitch: control_chl = 161,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 20.988000] BW = 2,TXStream = 4, RXStream = 4, scan(1) [ 21.204000] ==================================================================== [ 21.208000] Channel 36 : Busy Time = 271, Skip Channel = FALSE, BwCap = TRUE [ 21.216000] Channel 40 : Busy Time = 12, Skip Channel = FALSE, BwCap = TRUE [ 21.224000] Channel 44 : Busy Time = 109, Skip Channel = FALSE, BwCap = TRUE [ 21.232000] Channel 48 : Busy Time = 513, Skip Channel = FALSE, BwCap = TRUE [ 21.240000] Channel 149 : Busy Time = 361, Skip Channel = FALSE, BwCap = TRUE [ 21.248000] Channel 153 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE [ 21.252000] Channel 157 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE [ 21.260000] Channel 161 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE [ 21.268000] ==================================================================== [ 21.276000] Rule 3 Channel Busy time value : Select Primary Channel 153 [ 21.284000] Rule 3 Channel Busy time value : Min Channel Busy = 361 [ 21.288000] Rule 3 Channel Busy time value : BW = 80 [ 21.292000] AutoChSelUpdateChannel(): Update channel for wdev0 for this band PhyMode = 49,Channel = 153 [ 21.304000] AutoChSelUpdateChannel(): Update channel for wdev1 for this band PhyMode = 49,Channel = 153 [ 21.316000] AutoChSelUpdateChannel(): Update channel for wdev2 for this band PhyMode = 49,Channel = 153 [ 21.324000] AutoChSelUpdateChannel(): Update channel for wdev3 for this band PhyMode = 49,Channel = 153 [ 21.336000] AutoChSelUpdateChannel(): Update channel for wdev4 for this band PhyMode = 49,Channel = 153 [ 21.344000] ApAutoChannelAtBootUp<----------------- [ 21.352000] WifiSysOpen(), wdev idx = 0 [ 21.356000] wdev_attr_update(): wdevId0 = 68:ff:7b:2b:37:f6 [ 21.360000] MtCmdSetDbdcCtrl:(ret = 0) [ 21.364000] Current Channel is 153. DfsZeroWaitSupport=0 [ 21.368000] MtAsicSetChBusyStat(840): Not support for HIF_MT yet! [ 21.376000] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 21.380000] [PMF]WPAMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 [ 21.388000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 21.396000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 21.404000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 [ 21.404000] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 21.420000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [ 21.548000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 21.556000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 21.560000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 21.568000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 21.572000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155 [ 21.580000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 21.592000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 21.596000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 21.604000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 21.612000] BW = 2,TXStream = 4, RXStream = 4, scan(0) [ 21.636000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 21.660000] [WrapDfsRadarDetectStart]: Band0Ch is 153 [ 21.664000] [WrapDfsRadarDetectStart]: Band1Ch is 0 [ 21.672000] LeadTimeForBcn, OmacIdx = 0, WDEV_WITH_BCN_ABILITY [ 21.676000] MtAsicSetRalinkBurstMode(2605): Not support for HIF_MT yet! [ 21.684000] MtAsicSetPiggyBack(777): Not support for HIF_MT yet! [ 21.688000] MtAsicSetTxPreamble(2584): Not support for HIF_MT yet! [ 21.696000] RTMPSetLEDStatus: before AndesLedEnhanceOP , status=1, LED_CMD=2! [ 21.704000] AndesLedEnhanceOP: Success! [ 21.708000] Main bssid = 68:ff:7b:2b:37:f6 [ 21.712000] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 21.716000] MtCmdSetMacTxRx:(ret = 0) [ 21.720000] MCS Set = ff ff ff ff 01 [ 21.724000] <==== mt_wifi_init, Status=0 [ 21.728000] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 [ 21.732000] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 [ 21.764000] WtcSetMaxStaNum: MaxStaNum:87, BssidNum:5, WdsNum:0, ApcliNum:2, MaxNumChipRept:32, MinMcastWcid:121 [ 21.772000] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. [ 21.780000] Correct apidx from 0 to 0 for WscUUIDInit [ 21.784000] Generate UUID for apidx(0) wscd: SSDP UDP PORT = 1900 [ 21.836000] WifiSysOpen(), wdev idx = 1 [ 21.840000] wdev_attr_update(): wdevId1 = 6a:ff:7b:1b:37:f6 [ 21.844000] MtCmdSetDbdcCtrl:(ret = 0) [ 21.848000] [PMF]APPMFInit:: apidx=1, MFPC=0, MFPR=0, SHA256=0 [ 21.856000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 21.864000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 21.872000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 21.880000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:126 for WDEV_TYPE:1 [ 21.880000] LinkToOmacIdx = 11, LinkToWdevType = 1 [ 21.896000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 21.900000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [ 21.916000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 21.920000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 21.928000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 21.932000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155 [ 21.940000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 21.952000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 21.956000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 21.964000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 21.972000] BW = 2,TXStream = 4, RXStream = 4, scan(0) [ 21.992000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 22.016000] [WrapDfsRadarDetectStart]: Band0Ch is 153 [ 22.020000] [WrapDfsRadarDetectStart]: Band1Ch is 0 [ 22.028000] LeadTimeForBcn, OmacIdx = 11, WDEV_WITH_BCN_ABILITY [ 22.032000] Generate UUID for apidx(1) [ 22.040000] WifiSysOpen(), wdev idx = 2 [ 22.044000] wdev_attr_update(): wdevId2 = 6a:ff:7b:2b:37:f6 [ 22.048000] MtCmdSetDbdcCtrl:(ret = 0) [ 22.052000] [PMF]APPMFInit:: apidx=2, MFPC=0, MFPR=0, SHA256=0 [ 22.060000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.068000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.076000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.084000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 22.096000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:125 for WDEV_TYPE:1 [ 22.096000] LinkToOmacIdx = 12, LinkToWdevType = 1 [ 22.108000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 22.112000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [ 22.128000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 22.136000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 22.140000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 22.148000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155 [ 22.156000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 22.164000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 22.168000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 22.176000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 22.188000] BW = 2,TXStream = 4, RXStream = 4, scan(0) [ 22.204000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 22.228000] [WrapDfsRadarDetectStart]: Band0Ch is 153 [ 22.236000] [WrapDfsRadarDetectStart]: Band1Ch is 0 [ 22.240000] LeadTimeForBcn, OmacIdx = 12, WDEV_WITH_BCN_ABILITY [ 22.244000] Generate UUID for apidx(2) [ 22.252000] WifiSysOpen(), wdev idx = 3 [ 22.256000] wdev_attr_update(): wdevId3 = 6a:ff:7b:3b:37:f6 [ 22.264000] MtCmdSetDbdcCtrl:(ret = 0) [ 22.268000] [PMF]APPMFInit:: apidx=3, MFPC=0, MFPR=0, SHA256=0 [ 22.272000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.280000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.292000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.300000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.308000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 22.316000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:124 for WDEV_TYPE:1 [ 22.316000] LinkToOmacIdx = 13, LinkToWdevType = 1 [ 22.328000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 22.332000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [ 22.348000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 22.356000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 22.364000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 22.368000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155 [ 22.376000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 22.388000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 22.392000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 22.400000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 22.408000] BW = 2,TXStream = 4, RXStream = 4, scan(0) [ 22.428000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 22.452000] [WrapDfsRadarDetectStart]: Band0Ch is 153 [ 22.456000] [WrapDfsRadarDetectStart]: Band1Ch is 0 [ 22.460000] LeadTimeForBcn, OmacIdx = 13, WDEV_WITH_BCN_ABILITY [ 22.468000] Generate UUID for apidx(3) [ 22.476000] WifiSysOpen(), wdev idx = 4 [ 22.480000] wdev_attr_update(): wdevId4 = 6a:ff:7b:4b:37:f6 [ 22.484000] MtCmdSetDbdcCtrl:(ret = 0) [ 22.488000] [PMF]APPMFInit:: apidx=4, MFPC=0, MFPR=0, SHA256=0 [ 22.496000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.504000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.512000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.520000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.528000] HcUpdatePhyMode(): Update PhyMode for all wdev for this band PhyMode:49,Channel=153 [ 22.540000] CountryCode(2.4G/5G)=1/7, RFIC=25, PHY mode(2.4G/5G)=49/49, support 24 channels [ 22.548000] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:123 for WDEV_TYPE:1 [ 22.548000] LinkToOmacIdx = 14, LinkToWdevType = 1 [ 22.560000] [RadarStateCheck]Set into RD_NORMAL_MODE [ 22.564000] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196 [ 22.580000] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 1, BandIdx: 0 [ 22.588000] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 22.592000] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 22.600000] mt7615_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=153, HT-CentCh=151, VHT-CentCh=155 [ 22.608000] mt7615_apply_dcoc() : reload Central CH [155] BW [2] from cetral freq [5775] offset [2000] [ 22.616000] MtCmdGetRXDCOCCalResult:(ret = 0) [ 22.620000] mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload [ 22.628000] MtCmdChannelSwitch: control_chl = 153,control_ch2=0, central_chl = 155 DBDCIdx= 0, Band= 0 [ 22.640000] BW = 2,TXStream = 4, RXStream = 4, scan(0) [ 22.644000] :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) [ 22.660000] ap_phy_rrm_init_byRf(): AP Set CentralFreq at 155(Prim=153, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 22.684000] [WrapDfsRadarDetectStart]: Band0Ch is 153 [ 22.688000] [WrapDfsRadarDetectStart]: Band1Ch is 0 [ 22.692000] LeadTimeForBcn, OmacIdx = 14, WDEV_WITH_BCN_ABILITY [ 22.700000] Generate UUID for apidx(4) [ 22.708000] WifiSysClose(), wdev idx = 1 [ 22.708000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:1b:37:f6), Reason 0x10 [ 22.708000] Beacon lost - AP disabled!!! [ 22.712000] WifiSysGetBssInfoState(): BssInfoIdx 1 not found!!! [ 22.712000] WifiSysUpdateBssInfoState(): BssInfoIdx 1 not found!!! [ 22.740000] BndStrg is already Disable [ 22.748000] WifiSysClose(), wdev idx = 2 [ 22.748000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:2b:37:f6), Reason 0x10 [ 22.748000] Beacon lost - AP disabled!!! [ 22.756000] WifiSysGetBssInfoState(): BssInfoIdx 2 not found!!! [ 22.756000] WifiSysUpdateBssInfoState(): BssInfoIdx 2 not found!!! [ 22.784000] BndStrg is already Disable [ 22.784000] WifiSysClose(), wdev idx = 3 [ 22.792000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:3b:37:f6), Reason 0x10 [ 22.792000] Beacon lost - AP disabled!!! [ 22.800000] WifiSysGetBssInfoState(): BssInfoIdx 3 not found!!! [ 22.800000] WifiSysUpdateBssInfoState(): BssInfoIdx 3 not found!!! [ 22.824000] BndStrg is already Disable [ 22.832000] WifiSysClose(), wdev idx = 4 [ 22.832000] ExtEventBeaconLostHandler::FW LOG, Beacon lost (6a:ff:7b:4b:37:f6), Reason 0x10 [ 22.832000] Beacon lost - AP disabled!!! [ 22.840000] WifiSysGetBssInfoState(): BssInfoIdx 4 not found!!! [ 22.840000] WifiSysUpdateBssInfoState(): BssInfoIdx 4 not found!!! [ 22.868000] BndStrg is already Disable [ 22.868000] [ 22.876000] device rai0 entered promiscuous mode [ 22.880000] br0: port 11(rai0) entered forwarding state [ 22.888000] br0: port 11(rai0) entered forwarding state [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 [ 22.928000] device apclii0 entered promiscuous mode [ 22.936000] device rai2 entered promiscuous mode [ 22.944000] device rai3 entered promiscuous mode [ 22.952000] device rai4 entered promiscuous mode [ wlan_handleL2Desc ] 1089: br0 [ 22.960000] device rai1 entered promiscuous mode sh: wlNetlinkTool:[ 22.972000] is_cali: 1 not found wscd: SSDP UDP PORT = 1900 sendto: No such file or directory pid 881 send 2030 error set offset 214 as 0 for sch rate control. set offset 214 as 0 for sch rate control. sch set offset 4 as 0 for sch selection. rate set offset 4 as 8000000 for rate control. weight set offset 4 as 8000000 for max rate weight. sch set offset 14 as 0 for sch selection. sh: can't create /proc/sys/kernel/core_pattern: nonexistent directory rate set offset 14 as 8000000 for rate control. weight set offset 14 as 8000000 for max rate weight. sch set offset 24 as 0 for sch selection. rate set offset 24 as 8000000 for rate control. weight set offset 24 as 8000000 for max rate weight. sch set offset 34 as 0 for sch selection. rate set offset 34 as 8000000 for rate control. weight set offset 34 as 8000000 for max rate weight. sch set offset 44 as 0 for sch selection. rate set offset 44 as 8000000 for rate control. weight set offset 44 as 8000000 for max rate weight. sch set offset 54 as 0 for sch selection. rate set offset 54 as 8000000 for rate control. weight set offset 54 as 8000000 for max rate weight. sch set offset 64 as 0 for sch selection. rate set offset 64 as 8000000 for rate control. weight set offset 64 as 8000000 for max rate weight. sch set offset 74 as 0 for sch selection. rate set offset 74 as 8000000 for rate control. weight set offset 74 as 8000000 for max rate weight. sch set offset 84 as 80000000 for sch selection. rate set offset 84 as 88000000 for rate control. weight set offset 84 as 88000000 for max rate weight. sch set offset 94 as 80000000 for sch selection. rate set offset 94 as 88000000 for rate control. weight set offset 94 as 88000000 for max rate weight. sch set offset a4 as 80000000 for sch selection. rate set offset a4 as 88000000 for rate control. weight set offset a4 as 88000000 for max rate weight. sch set offset b4 as 80000000 for sch selection. rate set offset b4 as 88000000 for rate control. weight set offset b4 as 88000000 for max rate weight. sch set offset c4 as 80000000 for sch selection. rate set offset c4 as 88000000 for rate control. weight set offset c4 as 88000000 for max rate weight. sch set offset d4 as 80000000 for sch selection. rate set offset d4 as 88000000 for rate control. weight set offset d4 as 88000000 for max rate weight. sch set offset e4 as 80000000 for sch selection. rate set offset e4 as 88000000 for rate control. weight set offset e4 as 88000000 for max rate weight. sch set offset f4 as 80000000 for sch selection. rate set offset f4 as 88000000 for rate control. weight set offset f4 as 88000000 for max rate weight. [ 23.384000] tun: Universal TUN/TAP device driver, 1.6 [ 23.392000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko': No such file or directory [ rsl_getManagementServerObj ] 568: cannot set connectionRequestURL yet because no WAN intf is up iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). radvd starting brctl: bridge br0: Invalid argument brctl: bridge br0: Invalid argument [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 [ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation [ util_enFuncQueue ] 099: Function queue not support RDP_OPT_ADD_OBJ operation [ 23.604000] device eth1.2 entered promiscuous mode [ 23.608000] device eth1 entered promiscuous mode [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 1 : [3] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 2 : [4] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 3 : [5] [ rsl_getUnusedVlan ] 1268: GET UNUSED VLAN TAG 4 : [6] [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x5E [ mt7621_vlan_entry_update ] 245: vlanInfo.portMap = 0x21 iptables: Bad rule (does a matching rule exist in that chain?). insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko': File exists insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko': File exists iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). [ 23.764000] nf_conntrack_rtsp v0.6.21 loading [ 23.776000] nf_nat_rtsp v0.6.21 loading [ 23.856000] Ralink HW NAT Module Enabled [ 23.864000] eth0 ifindex =8 [ 23.864000] eth1 ifindex =9 ip6tables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). [ rsl_setStorageServiceObj ] 1403: mountFlag is 3,We start usb server killall: ushare: no process killed uShare (version 1.1a), a lightweight UPnP A/V and DLNA Media Server. Benjamin Zores (C) 2005-2007, for GeeXboX Team. See http://ushare.geexbox.org/ for updates. iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). sh: can't create /proc/tplink/eth_forward: nonexistent directory OPTIMIZED_FOR -> wifi NUM_OF_CPU -> 4 wifiDomain1 -> 5G wifiDomain2 -> 2_4G CONFIG_RALINK_MT7621 -> y CONFIG_ARCH_MT7623 -> sed: no address after comma sed: no address after comma sed: no address after comma sed: no address after comma sed: no address after comma igmpd# Msg: higher version IGMP pkt caught! Found 0 files and subdirectories. open DNS error: No such file or directory
OpenWrt bootlog
U-Boot 1.1.3 (Dec 29 2018 - 11:24:12) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f9c000 Config XHCI 40M PLL #Reset_MT7530 Allocate 16 byte aligned buffer: 87fca950 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 40] Device found in MTK table, ID: c8d1, EXT_ID: 809540 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 partable is: part0:0x20000@0x0 part1:0x7f60000@0x20000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Dec 29 2018 Time:11:24:12 ============================================ THIS IS First Uboot: The first uboot located in NAND Flash to load next full-feature Uboot. icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes set LAN/WAN WLLLL Press '1' or 't' to break the booting process 0 3: System Boot system code via Flash. ## Booting image at bc020000 ... Image Name: NAND Flash I Image Type: MIPS Linux Standalone Program (uncompressed) Data Size: 173024 Bytes = 169 kB Load Address: a01fc040 Entry Point: a0200000 ... Verifying Checksum ... OK data copied to 0xa01fc040 OK jump to memory 0xa0200000 U-Boot 1.1.3 (Dec 29 2018 - 11:24:16) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f8c000 Config XHCI 40M PLL #Reset_MT7530 Allocate 16 byte aligned buffer: 87fca6d0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C8 D1 80 95 40] Device found in MTK table, ID: c8d1, EXT_ID: 809540 Support this Device in MTK table! c8d1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 . partable is: uboot:0x400000@0x0 os0:0x3000000@0x400000 os1:0x3000000@0x3400000 userfs:0x1000000@0x6400000 ubootenv:0x400000@0x7400000 factory:0x400000@0x7800000 .============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Dec 29 2018 Time:11:24:16 ============================================ THIS IS Main Uboot: Including recovery webserver. icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes set LAN/WAN WLLLL this uboot is loaded from 0xbc020000 Press '4' or 't' to break the booting process Press 'x' to enter recovery web server 0 3: System Boot system code via Flash. do_bootm ## Booting image at bc400000 ... Image Name: OS IMAGE (OpenWrt) Image Type: MIPS Linux Firmware (uncompressed) Data Size: 2695773 Bytes = 2.6 MB Load Address: 80001000 Entry Point: 80001000 ret is -3 try next header ## Booting image at bc400040 ... Image Name: MIPS OpenWrt Linux-5.10.161 Image Type: MIPS Linux Standalone Program (uncompressed) Data Size: 2695709 Bytes = 2.6 MB Load Address: 80001000 Entry Point: 80001000 .......................................... Verifying Checksum ... OK data copied to 0x80001000 OK jump to memory 0x80001000 OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.10.161 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20028-43d71ad93e) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Tue Jan 3 00:24:21 2023 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TP-Link EC330-G5u v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=0006200c [ 0.000000] Readback ErrCtl register=0006200c [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119468K/131072K available (7039K kernel code, 631K rwdata, 832K rodata, 1276K init, 243K bss, 11604K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.007952] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.016995] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.083157] pid_max: default: 32768 minimum: 301 [ 0.087923] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.095125] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.105705] rcu: Hierarchical SRCU implementation. [ 0.110741] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.118834] smp: Bringing up secondary CPUs ... [ 0.124105] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.124116] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.124127] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.124203] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.178631] Synchronize counters for CPU 1: done. [ 0.211052] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.211061] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.211070] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.211117] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.270027] Synchronize counters for CPU 2: done. [ 0.300616] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.300625] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.300634] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.300685] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.355213] Synchronize counters for CPU 3: done. [ 0.385080] smp: Brought up 1 node, 4 CPUs [ 0.393646] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.403463] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.410474] pinctrl core: initialized pinctrl subsystem [ 0.418050] NET: Registered protocol family 16 [ 0.423593] thermal_sys: Registered thermal governor 'step_wise' [ 0.424962] cpuidle: using governor teo [ 0.471132] clocksource: Switched to clocksource GIC [ 0.477811] NET: Registered protocol family 2 [ 0.482487] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.491154] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.499482] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.507091] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.514073] TCP: Hash tables configured (established 1024 bind 1024) [ 0.520507] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.526993] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.534190] NET: Registered protocol family 1 [ 0.538484] PCI: CLS 0 bytes, default 32 [ 0.544824] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.555452] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.561230] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.571845] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.581158] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.587001] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.592959] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.599368] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.610041] printk: console [ttyS0] disabled [ 0.614366] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.623365] printk: console [ttyS0] enabled [ 0.623365] printk: console [ttyS0] enabled [ 0.631618] printk: bootconsole [early0] disabled [ 0.631618] printk: bootconsole [early0] disabled [ 0.643827] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1 [ 0.650180] nand: ESMT NAND 128MiB 3,3V 8-bit [ 0.654629] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.662199] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 0.668795] 7 fixed-partitions partitions found on MTD device mt7621-nand [ 0.676151] Creating 7 MTD partitions on "mt7621-nand": [ 0.681421] 0x000000000000-0x000000400000 : "u-boot" [ 0.748650] 3 fixed-partitions partitions found on MTD device u-boot [ 0.755029] Creating 3 MTD partitions on "u-boot": [ 0.759808] 0x000000000000-0x000000020000 : "u-boot-first" [ 0.768081] 0x000000020000-0x000000060000 : "u-boot-main" [ 0.778245] 0x000000060000-0x0000000a0000 : "u-boot-main-reserve" [ 0.789143] 0x000000400000-0x000003400000 : "os0" [ 1.530667] 2 fixed-partitions partitions found on MTD device os0 [ 1.536823] Creating 2 MTD partitions on "os0": [ 1.541472] 0x000000000000-0x000000400000 : "kernel" [ 1.608709] 0x000000400000-0x000003000000 : "ubi-os0" [ 2.289186] 0x000003400000-0x000006400000 : "os1" [ 3.030532] 0x000006400000-0x000007400000 : "userfs" [ 3.282032] 0x000007400000-0x000007800000 : "u-boot-env" [ 3.349854] 0x000007800000-0x000007c00000 : "factory" [ 3.417384] 0x000000000000-0x000007f80000 : "wholeflash" [ 5.385793] Concatenating MTD devices: [ 5.389571] (0): "ubi-os0" [ 5.392301] (1): "userfs" [ 5.394907] into device "ubi-concat" [ 5.398526] 1 fixed-partitions partitions found on MTD device ubi-concat [ 5.405218] Creating 1 MTD partitions on "ubi-concat": [ 5.410341] 0x000000000000-0x000003c00000 : "ubi" [ 6.382287] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.392104] mtk_soc_eth 1e100000.ethernet: generated random MAC address e2:53:8a:2d:6b:45 [ 6.401222] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 6.409680] mtk_soc_eth 1e100000.ethernet: generated random MAC address 7a:5f:9b:98:d8:cd [ 6.418679] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21 [ 6.427826] i2c /dev entries driver [ 6.434229] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 6.440997] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 6.449778] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 6.457950] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 6.466226] mt7621-pci 1e140000.pcie: Parsing DT failed [ 6.473799] NET: Registered protocol family 10 [ 6.480037] Segment Routing with IPv6 [ 6.483855] NET: Registered protocol family 17 [ 6.488367] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 6.501744] 8021q: 802.1Q VLAN Support v1.8 [ 6.509411] gpio-export gpio-export: 1 gpio(s) exported [ 6.515010] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 6.544231] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27) [ 6.556757] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28) [ 6.569051] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29) [ 6.581412] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30) [ 6.594046] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 6.604516] DSA: tree 0 setup [ 6.607841] rt2880-pinmux pinctrl: pcie is already enabled [ 6.613422] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 6.620106] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 6.628906] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 6.637083] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 6.645353] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 6.653193] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 6.660910] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 6.768315] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 6.773904] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 6.879626] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 6.886581] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 6.891459] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 6.896320] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 6.905780] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 6.912168] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 6.919020] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 6.925889] pci_bus 0000:00: root bus resource [bus 00-ff] [ 6.931379] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 6.941581] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 6.947579] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 6.953843] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 6.960891] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000] [ 6.966681] pci 0000:00:00.0: supports D1 [ 6.970672] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 6.976929] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 6.982991] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 6.989235] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid [ 6.996274] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000] [ 7.002084] pci 0000:00:01.0: supports D1 [ 7.006077] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 7.013404] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.021442] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 7.029682] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 7.035753] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.042805] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 7.049217] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 7.065603] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 7.070886] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 7.076957] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 7.083749] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref] [ 7.090976] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 7.097838] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280 [ 7.103907] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 7.110973] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 7.117387] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 7.133777] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 7.139000] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 7.145115] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff] [ 7.151898] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref] [ 7.159094] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 7.165754] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 7.172364] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.179298] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 7.185912] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 7.192870] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 7.199631] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 7.206860] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 7.213647] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 7.220868] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 7.227633] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 7.234414] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 7.241199] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 7.247966] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 7.255276] pci 0000:00:00.0: PCI bridge to [bus 01] [ 7.260220] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 7.267008] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 7.273791] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 7.281015] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff 64bit] [ 7.288302] pci 0000:00:01.0: PCI bridge to [bus 02] [ 7.293267] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 7.300027] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 7.306806] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 7.318329] UBI: auto-attach mtd12 [ 7.321839] ubi0: attaching mtd12 [ 7.331445] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.869338] ubi0: scanning is finished [ 8.889919] ubi0: attached mtd12 (name "ubi", size 60 MiB) [ 8.895440] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 8.902304] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 8.909061] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 8.916004] ubi0: good PEBs: 480, bad PEBs: 0, corrupted PEBs: 0 [ 8.921999] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 8.929188] ubi0: max/mean erase counter: 15/8, WL threshold: 4096, image sequence number: 2014637619 [ 8.938378] ubi0: available PEBs: 0, total reserved PEBs: 480, PEBs reserved for bad PEB handling: 10 [ 8.947606] ubi0: background thread "ubi_bgt0d" started, PID 484 [ 8.950062] block ubiblock0_0: created from ubi0:0(rootfs) [ 8.959149] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 8.973604] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 8.985010] Freeing unused kernel memory: 1276K [ 8.989540] This architecture does not have kernel memory protection. [ 8.995991] Run /sbin/init as init process [ 9.553648] init: Console is alive [ 9.557433] init: - watchdog - [ 10.384711] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 10.512153] usbcore: registered new interface driver usbfs [ 10.517795] usbcore: registered new interface driver hub [ 10.523267] usbcore: registered new device driver usb [ 10.539472] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 10.547244] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 10.555128] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 10.560465] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 10.581048] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 10.590223] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 10.597271] hub 1-0:1.0: USB hub found [ 10.601242] hub 1-0:1.0: 2 ports detected [ 10.605898] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 10.611325] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 10.618810] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 10.625392] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 10.634465] hub 2-0:1.0: USB hub found [ 10.638356] hub 2-0:1.0: 1 port detected [ 10.650110] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 10.671305] init: - preinit - [ 11.455330] random: jshn: uninitialized urandom read (4 bytes read) [ 11.534864] random: jshn: uninitialized urandom read (4 bytes read) [ 11.645483] random: jshn: uninitialized urandom read (4 bytes read) [ 11.966275] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 11.974663] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 11.981462] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 11.990000] 8021q: adding VLAN 0 to HW filter on device lan1 [ 11.998286] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 16.197291] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 16.203312] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 638 [ 16.286232] UBIFS (ubi0:1): recovery needed [ 16.495769] UBIFS (ubi0:1): recovery completed [ 16.500374] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 16.508205] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.518092] UBIFS (ubi0:1): FS size: 53456896 bytes (50 MiB, 421 LEBs), journal size 2666496 bytes (2 MiB, 21 LEBs) [ 16.528493] UBIFS (ubi0:1): reserved for root: 2524900 bytes (2465 KiB) [ 16.535093] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID F4719F63-F61D-4C85-9044-D79236319105, small LPT model [ 16.553327] mount_root: switching to ubifs overlay [ 16.577820] urandom-seed: Seeding with /etc/urandom.seed [ 16.705853] procd: - early - [ 16.708984] procd: - watchdog - [ 17.371093] procd: - watchdog - [ 17.481978] procd: - ubus - [ 17.623742] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.641761] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.648621] random: ubusd: uninitialized urandom read (4 bytes read) [ 17.661637] procd: - init - Please press Enter to activate this console. [ 18.492311] kmodloader: loading kernel modules from /etc/modules.d/* [ 18.686648] urngd: v1.0.2 started. [ 18.796950] Loading modules backported from Linux version v5.15.81-0-ge4a7232c917c [ 18.804580] Backport generated by backports.git v5.15.81-1-0-ge1867d55 [ 18.864950] random: crng init done [ 18.868374] random: 30 urandom warning(s) missed due to ratelimiting [ 19.016900] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 19.022365] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 19.028008] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 19.051640] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 19.057129] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 19.062872] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 19.072496] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 19.072496] [ 19.105210] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 19.105210] [ 19.187417] PPP generic driver version 2.4.2 [ 19.195254] NET: Registered protocol family 24 [ 19.213532] kmodloader: done loading kernel modules from /etc/modules.d/* [ 19.397781] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 19.400996] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 19.532881] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 19.532926] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 27.782081] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 27.801640] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 27.809866] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 27.813921] device eth0 entered promiscuous mode [ 27.823527] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 27.830606] 8021q: adding VLAN 0 to HW filter on device lan1 [ 27.839273] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.846753] br-lan: port 1(lan1) entered blocking state [ 27.852169] br-lan: port 1(lan1) entered disabled state [ 27.859075] device lan1 entered promiscuous mode [ 27.889006] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 27.896563] 8021q: adding VLAN 0 to HW filter on device lan2 [ 27.906982] br-lan: port 2(lan2) entered blocking state [ 27.912763] br-lan: port 2(lan2) entered disabled state [ 27.919462] device lan2 entered promiscuous mode [ 27.935589] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 27.943001] 8021q: adding VLAN 0 to HW filter on device lan3 [ 27.953223] br-lan: port 3(lan3) entered blocking state [ 27.958491] br-lan: port 3(lan3) entered disabled state [ 27.966206] device lan3 entered promiscuous mode [ 27.981042] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 27.988422] 8021q: adding VLAN 0 to HW filter on device lan4 [ 27.998785] br-lan: port 4(lan4) entered blocking state [ 28.004175] br-lan: port 4(lan4) entered disabled state [ 28.012447] device lan4 entered promiscuous mode [ 28.037698] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [MediaTek MT7530 PHY] (irq=POLL) [ 28.047398] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii-rxid link mode BusyBox v1.35.0 (2023-01-03 00:24:21 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 22.03.3, r20028-43d71ad93e ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#
Notes
None so far.