Sinovoip BananaPi M2 Plus

The board is available from various vendors, including the manufacturer itself, see here for BananaPi.

For further Allwinner-based boards, please refer to soc.allwinner.sunxi

Model Ports
BananaPi MMC, SATA, RCA video-out, HDMI, sound

Remember: HDMI Output is not available in OpenWrt by default. Use console instead.

Please refer to soc.allwinner.sunxi.

You can use your usual serial levelshifter. Pinout is described on silkscreen PCB.

U-Boot SPL 2018.11 (Feb 15 2019 - 16:36:57 +0000) DRAM: 1024 MiB Trying to boot from MMC1 U-Boot 2018.11 (Feb 15 2019 - 16:36:57 +0000) Allwinner Technology CPU: Allwinner H3 (SUN8I 1680) Model: Banana Pi BPI-M2-Plus DRAM: 1 GiB MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Allwinner mUSB OTG (Peripheral) Net: phy interface7 eth0: ethernet@1c30000 Warning: usb_ether using MAC address from ROM , eth1: usb_ether starting USB... USB0: USB EHCI 1.00 USB1: USB OHCI 1.0 USB2: USB EHCI 1.00 USB3: USB OHCI 1.0 USB4: USB EHCI 1.00 USB5: USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found scanning bus 4 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot.scr 377 bytes read in 1 ms (368.2 KiB/s) ## Executing script at 43100000 2651440 bytes read in 120 ms (21.1 MiB/s) 16057 bytes read in 2 ms (7.7 MiB/s) ## Booting kernel from Legacy Image at 42000000 ... Image Name: ARM OpenWrt Linux-4.14.98 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2651376 Bytes = 2.5 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 EHCI failed to shut down host controller. EHCI failed to shut down host controller. Loading Kernel Image ... OK Using Device Tree in place at 43000000, end 43006eb8 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.98 (krolik@ubuntu-VirtualBox) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9301-ad61d75478)) #0 SMP PREEMPT Fri Feb 15 15:08:53 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M2-Plus [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x3f8 with crng_init=0 [ 0.000000] percpu: Embedded 16 pages/cpu @ef7ac000 s34828 r8192 d22516 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1028360K/1048576K available (5293K kernel code, 343K rwdata, 1504K rodata, 2048K init, 240K bss, 20216K reserved, 0K cma-reserved, 262132K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc072b648 (7310 kB) [ 0.000000] .init : 0xc0a00000 - 0xc0c00000 (2048 kB) [ 0.000000] .data : 0xc0c00000 - 0xc0c55e00 ( 344 kB) [ 0.000000] .bss : 0xc0c5c43c - 0xc0c98690 ( 241 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000017] Switching to timer-based delay loop, resolution 41ns [ 0.000149] Console: colour dummy device 80x30 [ 0.000183] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000196] pid_max: default: 32768 minimum: 301 [ 0.000304] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000317] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000779] CPU: Testing write buffer coherency: ok [ 0.001061] /cpus/cpu@0 missing clock-frequency property [ 0.001081] /cpus/cpu@1 missing clock-frequency property [ 0.001096] /cpus/cpu@2 missing clock-frequency property [ 0.001113] /cpus/cpu@3 missing clock-frequency property [ 0.001125] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.040044] Setting up static identity map for 0x40200000 - 0x40200060 [ 0.060044] Hierarchical SRCU implementation. [ 0.100097] smp: Bringing up secondary CPUs ... [ 0.180483] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.260611] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.340735] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.340811] smp: Brought up 1 node, 4 CPUs [ 0.340832] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.340839] CPU: All CPU(s) started in HYP mode. [ 0.340844] CPU: Virtualization extensions available. [ 0.344393] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.344837] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.344859] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.345044] pinctrl core: initialized pinctrl subsystem [ 0.346152] NET: Registered protocol family 16 [ 0.346403] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.347800] No ATAGs? [ 0.392364] SCSI subsystem initialized [ 0.392637] usbcore: registered new interface driver usbfs [ 0.392687] usbcore: registered new interface driver hub [ 0.392769] usbcore: registered new device driver usb [ 0.392902] pps_core: LinuxPPS API ver. 1 registered [ 0.392914] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.392947] PTP clock support registered [ 0.393269] Advanced Linux Sound Architecture Driver Initialized. [ 0.394409] clocksource: Switched to clocksource arch_sys_counter [ 0.399014] NET: Registered protocol family 2 [ 0.399536] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.399613] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.399728] TCP: Hash tables configured (established 8192 bind 8192) [ 0.399824] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.399880] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.400063] NET: Registered protocol family 1 [ 0.400387] kvm [1]: 8-bit VMID [ 0.402350] kvm [1]: vgic interrupt IRQ16 [ 0.402521] kvm [1]: Hyp mode initialized successfully [ 0.403754] No memory allocated for crashlog [ 0.403886] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.407736] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.407888] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.410036] bounce: pool size: 64 pages [ 0.410065] io scheduler noop registered [ 0.410073] io scheduler deadline registered [ 0.410207] io scheduler cfq registered (default) [ 0.410790] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 0.414133] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.415642] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 0.451240] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.453143] console [ttyS0] disabled [ 0.473618] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 38, base_baud = 1500000) is a U6_16550A [ 1.082116] console [ttyS0] enabled [ 1.106668] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 39, base_baud = 1500000) is a U6_16550A [ 1.120067] loop: module loaded [ 1.124637] libphy: Fixed MDIO Bus: probed [ 1.129371] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 1.135738] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.142260] ehci-platform: EHCI generic platform driver [ 1.147664] ehci-platform 1c1a000.usb: EHCI Host Controller [ 1.153252] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1 [ 1.161125] ehci-platform 1c1a000.usb: irq 27, io mem 0x01c1a000 [ 1.194426] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 [ 1.200690] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.207492] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.214716] usb usb1: Product: EHCI Host Controller [ 1.219588] usb usb1: Manufacturer: Linux 4.14.98 ehci_hcd [ 1.225079] usb usb1: SerialNumber: 1c1a000.usb [ 1.229983] hub 1-0:1.0: USB hub found [ 1.233762] hub 1-0:1.0: 1 port detected [ 1.238292] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.244503] ohci-platform: OHCI generic platform driver [ 1.249887] ohci-platform 1c1a400.usb: Generic Platform OHCI controller [ 1.256534] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2 [ 1.264371] ohci-platform 1c1a400.usb: irq 28, io mem 0x01c1a400 [ 1.338580] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.346166] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.353381] usb usb2: Product: Generic Platform OHCI controller [ 1.359306] usb usb2: Manufacturer: Linux 4.14.98 ohci_hcd [ 1.364799] usb usb2: SerialNumber: 1c1a400.usb [ 1.369670] hub 2-0:1.0: USB hub found [ 1.373445] hub 2-0:1.0: 1 port detected [ 1.378025] usbcore: registered new interface driver usb-storage [ 1.384238] mousedev: PS/2 mouse device common for all mice [ 1.390206] i2c /dev entries driver [ 1.394320] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.402541] cpu cpu0: failed to get clock: -2 [ 1.406935] cpufreq-dt: probe of cpufreq-dt failed with error -2 [ 1.414014] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.474440] sunxi-mmc 1c0f000.mmc: base:0xf08c7000 irq:23 [ 1.480494] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq [ 1.531462] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.541437] mmc0: new high speed SDHC card at address 1234 [ 1.546951] sunxi-mmc 1c10000.mmc: base:0xf08cb000 irq:24 [ 1.553352] mmcblk0: mmc0:1234 SA08G 7.21 GiB [ 1.559730] mmcblk0: p1 p2 [ 1.574626] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 1.581604] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.588594] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.596759] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.604428] sunxi-mmc 1c11000.mmc: base:0xf08cf000 irq:25 [ 1.611773] NET: Registered protocol family 10 [ 1.617269] Segment Routing with IPv6 [ 1.622074] NET: Registered protocol family 17 [ 1.628636] can: controller area network core (rev 20170425 abi 9) [ 1.634924] NET: Registered protocol family 29 [ 1.639395] 8021q: 802.1Q VLAN Support v1.8 [ 1.643705] Registering SWP/SWPB emulation handler [ 1.659125] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 1.693959] random: fast init done [ 1.699601] mmc2: new DDR MMC card at address 0001 [ 1.704836] mmcblk2: mmc2:0001 8WPD3R 7.28 GiB [ 1.709520] mmcblk2boot0: mmc2:0001 8WPD3R partition 1 4.00 MiB [ 1.715641] mmcblk2boot1: mmc2:0001 8WPD3R partition 2 4.00 MiB [ 1.722362] mmcblk2: p1 p2 [ 1.766607] mmc1: new high speed SDIO card at address 0001 [ 1.784468] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 50006 (expect 58000) [ 1.793779] dwmac-sun8i 1c30000.ethernet: Chain mode enabled [ 1.799466] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported [ 1.806695] dwmac-sun8i 1c30000.ethernet: Normal descriptors [ 1.812347] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported [ 1.819568] dwmac-sun8i 1c30000.ethernet: COE Type 2 [ 1.824536] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported [ 1.831426] libphy: stmmac: probed [ 1.835483] dwmac-sun8i 1c30000.ethernet: Found internal PHY node [ 1.841665] libphy: mdio_mux: probed [ 1.845272] dwmac-sun8i 1c30000.ethernet: Switch mux to internal PHY [ 1.851622] dwmac-sun8i 1c30000.ethernet: Powering internal PHY [ 1.858236] libphy: mdio_mux: probed [ 1.861824] dwmac-sun8i 1c30000.ethernet: Switch mux to external PHY [ 1.869173] ehci-platform 1c1b000.usb: EHCI Host Controller [ 1.874785] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 3 [ 1.882659] ehci-platform 1c1b000.usb: irq 29, io mem 0x01c1b000 [ 1.914426] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 [ 1.920685] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.927486] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.934709] usb usb3: Product: EHCI Host Controller [ 1.939581] usb usb3: Manufacturer: Linux 4.14.98 ehci_hcd [ 1.945072] usb usb3: SerialNumber: 1c1b000.usb [ 1.949981] hub 3-0:1.0: USB hub found [ 1.953768] hub 3-0:1.0: 1 port detected [ 1.958341] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.963931] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 4 [ 1.971797] ehci-platform 1c1c000.usb: irq 31, io mem 0x01c1c000 [ 2.004425] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 2.010664] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.017465] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.024688] usb usb4: Product: EHCI Host Controller [ 2.029560] usb usb4: Manufacturer: Linux 4.14.98 ehci_hcd [ 2.035051] usb usb4: SerialNumber: 1c1c000.usb [ 2.039922] hub 4-0:1.0: USB hub found [ 2.043698] hub 4-0:1.0: 1 port detected [ 2.048234] ohci-platform 1c1b400.usb: Generic Platform OHCI controller [ 2.054884] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 5 [ 2.062726] ohci-platform 1c1b400.usb: irq 30, io mem 0x01c1b400 [ 2.138567] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.145373] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.152587] usb usb5: Product: Generic Platform OHCI controller [ 2.158515] usb usb5: Manufacturer: Linux 4.14.98 ohci_hcd [ 2.163994] usb usb5: SerialNumber: 1c1b400.usb [ 2.168891] hub 5-0:1.0: USB hub found [ 2.172670] hub 5-0:1.0: 1 port detected [ 2.177225] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 2.183852] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 6 [ 2.191710] ohci-platform 1c1c400.usb: irq 32, io mem 0x01c1c400 [ 2.268572] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.275378] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.282592] usb usb6: Product: Generic Platform OHCI controller [ 2.288519] usb usb6: Manufacturer: Linux 4.14.98 ohci_hcd [ 2.293998] usb usb6: SerialNumber: 1c1c400.usb [ 2.298889] hub 6-0:1.0: USB hub found [ 2.302665] hub 6-0:1.0: 1 port detected [ 2.306938] hctosys: unable to open rtc device (rtc0) [ 2.312468] vcc3v0: disabling [ 2.315455] vcc5v0: disabling [ 2.318420] usb0-vbus: disabling [ 2.321644] ALSA device list: [ 2.324620] No soundcards found. [ 2.334003] VFS: Mounted root (squashfs filesystem) readonly on device 179:2. [ 2.343229] Freeing unused kernel memory: 2048K [ 2.579971] init: Console is alive [ 2.583548] init: - watchdog - [ 2.752194] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.799185] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.808982] init: - preinit - [ 3.115326] random: jshn: uninitialized urandom read (4 bytes read) [ 3.142987] random: jshn: uninitialized urandom read (4 bytes read) [ 3.162154] random: jshn: uninitialized urandom read (4 bytes read) [ 3.181145] Generic PHY 0.2:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0.2:00, irq=POLL) [ 3.191753] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available [ 3.199434] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW [ 3.207300] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.802459] F2FS-fs (loop0): Mounted with checkpoint version = 5ccce277 [ 6.809976] mount_root: switching to f2fs overlay [ 6.937315] urandom-seed: Seeding with /etc/urandom.seed [ 7.003338] procd: - early - [ 7.006408] procd: - watchdog - [ 7.754482] procd: - watchdog - [ 7.757852] procd: - ubus - [ 7.774096] urandom_read: 1 callbacks suppressed [ 7.774104] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.810920] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.817521] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.824344] procd: - init - Please press Enter to activate this console. [ 7.986379] kmodloader: loading kernel modules from /etc/modules.d/* [ 7.994978] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.007260] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0 [ 8.014830] Backport generated by backports.git v4.19.7-1-0-g148b072d [ 8.022593] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.031834] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 8.059615] xt_time: kernel timezone is -0000 [ 8.075429] PPP generic driver version 2.4.2 [ 8.080687] NET: Registered protocol family 24 [ 8.092697] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430a0-sdio for chip BCM43430/0 [ 8.196933] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430a0-sdio.sinovoip,bpi-m2-plus.txt failed with error -2 [ 8.208699] brcmfmac mmc1:0001:1: Falling back to user helper [ 8.223334] firmware brcm!brcmfmac43430a0-sdio.sinovoip,bpi-m2-plus.txt: firmware_loading_store: map pages failed [ 8.319716] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430a0-sdio for chip BCM43430/0 [ 8.328723] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43430a0-sdio.clm_blob failed with error -2 [ 8.339080] brcmfmac mmc1:0001:1: Falling back to user helper [ 8.353415] firmware brcm!brcmfmac43430a0-sdio.clm_blob: firmware_loading_store: map pages failed [ 8.362613] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-11), device may have limited channels available [ 8.377964] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/0 wl0: May 29 2017 00:03:43 version 7.13.53.9 (r664949) FWID 01-130000 [ 8.453548] usbcore: registered new interface driver brcmfmac [ 8.461301] kmodloader: done loading kernel modules from /etc/modules.d/* [ 10.637045] Generic PHY 0.2:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0.2:00, irq=POLL) [ 10.648315] dwmac-sun8i 1c30000.ethernet eth0: No MAC Management Counters available [ 10.656083] dwmac-sun8i 1c30000.ethernet eth0: PTP not supported by HW [ 10.663310] br-lan: port 1(eth0) entered blocking state [ 10.668659] br-lan: port 1(eth0) entered disabled state [ 10.674307] device eth0 entered promiscuous mode [ 10.680746] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 11.186813] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.195349] br-lan: port 2(wlan0) entered blocking state [ 11.200673] br-lan: port 2(wlan0) entered disabled state [ 11.206462] device wlan0 entered promiscuous mode [ 11.211303] br-lan: port 2(wlan0) entered blocking state [ 11.216657] br-lan: port 2(wlan0) entered forwarding state [ 11.222322] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 11.375661] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready


root@OpenWrt:/# cat /proc/cpuinfo
processor       : 0
model name      : ARMv7 Processor rev 5 (v7l)
BogoMIPS        : 48.00
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 5

processor       : 1
model name      : ARMv7 Processor rev 5 (v7l)
BogoMIPS        : 48.00
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 5

processor       : 2
model name      : ARMv7 Processor rev 5 (v7l)
BogoMIPS        : 48.00
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 5

processor       : 3
model name      : ARMv7 Processor rev 5 (v7l)
BogoMIPS        : 48.00
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 5

Hardware        : Allwinner sun8i Family
Revision        : 0000
Serial          : 02c00081d5db3811

root@OpenWrt:/# 
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1