Show pagesourceOld revisionsBacklinksBack to top × Table of Contents Qxwlan E2600AC C1/C2 Supported Versions Hardware Highlights Installation U-boot controller Default FLASH Layout Hardware Info Specification Photos Motherboard description Tags Qxwlan E2600AC C1/C2 Supported Versions BrandModel↓ VersionCurrent ReleaseOEM InfoForum TopicTechnical DataQxwlanE2600ACC121.02.6http://qxwlan.com/product/p/91.htmlView/Edit dataQxwlanE2600ACC222.03.5http://qxwlan.com/product/p/91.htmlView/Edit data Hardware Highlights Model↓ VersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBE2600ACC1Qualcomm IPQ4019¿32256Qualcomm IPQ4019b/g/na/n/ac--1x 3.0E2600ACC2Qualcomm IPQ4019¿16256Qualcomm Atheros IPQ4019b/g/na/n/ac--1x 3.0 Installation Model↓ VersionCurrent ReleaseFirmware OpenWrt InstallFirmware OpenWrt UpgradeOEM Stock URLE2600ACC121.02.6https://downloads.openwrt.org/releases/21.02.6/targets/ipq40xx/generic/openwrt-21.02.6-ipq40xx-generic-qxwlan_e2600ac-c1-squashfs-sysupgrade.binhttps://downloads.openwrt.org/releases/21.02.6/targets/ipq40xx/generic/openwrt-21.02.6-ipq40xx-generic-qxwlan_e2600ac-c1-squashfs-sysupgrade.binhttp://qxwlan.com/product/p/91.htmlE2600ACC222.03.5https://downloads.openwrt.org/releases/22.03.5/targets/ipq40xx/generic/openwrt-22.03.5-ipq40xx-generic-qxwlan_e2600ac-c2-squashfs-nand-factory.ubihttps://downloads.openwrt.org/releases/22.03.5/targets/ipq40xx/generic/openwrt-22.03.5-ipq40xx-generic-qxwlan_e2600ac-c2-squashfs-nand-sysupgrade.binhttp://qxwlan.com/product/p/91.html Flash instruction (using U-Boot web-based recovery): Configure PC with static IP 192.168.1.xxx(2-254)/24. Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. Open your browser and enter 192.168.1.1, if your board is e2600ac c1, select “sysupgrade” image and click the upgrade button. Open your browser and enter 192.168.1.1, if your board is e2600ac c2, select “ubi” image and click the upgrade button. Firmware OpenWrt Install: E2600AC C1/C2, select “xxx-sysupgrade.bin” U-boot controller U-Boot 2012.07 [local,local] (Dec 27 2018 - 16:15:16) Qxwlan E2600AC-C2 Support (nor-nand) smem ram ptable found: ver: 1 len: 3 DRAM: 256 MiB machid : 0x8010206 NAND: ID = 9580f12c Vendor = 2c Device = f1 ONFI device found SF: Detected W25Q128 with page size 64 KiB, total 16 MiB ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000 144 MiB MMC: qca_mmc: 0 In: serial Out: serial Err: serial machid: 8010206 flash_type: 0 Net: MAC0 addr:dc:eb:53:11:bf:a0 PHY ID1: 0x4d PHY ID2: 0xd0b1 ipq40xx_ess_sw_init done eth0 Hit any key to stop autoboot: 0 (IPQ40xx) # Default FLASH Layout 1 fixed-partitions partitions found on MTD device qcom_nand.0 Creating 1 MTD partitions on "qcom_nand.0": 0x000000000000-0x000004000000 : "ubi" m25p80 spi0.0: w25q128 (16384 Kbytes) 8 fixed-partitions partitions found on MTD device spi0.0 NAND Flash Partition Start End Size Erasesize Name mtd0 0x000000000000 0x000004000000 0x04000000 0x00010000 ubi NOR Flash Partition Start End Size Erasesize Name mtd1 0x000000000000 0x000000040000 0x00040000 0x00010000 0:SBL1 mtd2 0x000000040000 0x000000060000 0x00020000 0x00010000 0:MIBIB mtd3 0x000000060000 0x0000000c0000 0x00060000 0x00010000 0:QSEE mtd4 0x0000000c0000 0x0000000d0000 0x00010000 0x00010000 0:CDT mtd5 0x0000000d0000 0x0000000e0000 0x00010000 0x00010000 0:DDRPARAMS mtd6 0x0000000e0000 0x0000000f0000 0x00010000 0x00010000 0:APPSBLENV mtd7 0x0000000f0000 0x000000170000 0x00080000 0x00010000 0:APPSBL mtd8 0x000000170000 0x000000180000 0x00010000 0x00010000 0:ART Hardware Info Architecture ARM bootloader web u-boot System-On-Chip IPQ4019 + QCA8075 Flash size 16 M NOR-Flash + 128M Nand-Flash RAM 256 MB DDR3 RAM Wireless WiFi 11ac/g/n with IPQ4019 Ethernet 3x 10/100/1000 Base-T(X) (one port support POE) Antenna 2T2R 2.4 GHz 2T2R 5L/H GHz MMCX*6 USB 1x 3.0 (host) PCIE 1x miniPCIE SIM 1x microSIM slot SD 1x sd card slot Serial YES ( RS232 (soldering needed)) LED Standard Ethernet LED's, WIFI LED Hardware buttons reset button Power 1x DC jack for main power input (9-48 V) Board Size 155 x 118 x 17mm (L x W x H) Specification 256 MB of RAM (DDR3) 16 MB of FLASH (SPI NOR) 128 MB of FLASH (NAND) 2T2R 2.4 GHz 2T2R 5L/H GHz 3x 10/100/1000 Mbps Ethernet (one port with PoE support) 1x miniPCIe slot 11x LED (10 driven by GPIO) 1x 2-pos switch Photos Motherboard description Serial connection settings: 115200 8N1, no hardware flow control. Tags How to add tags ipq40xx, IPQ4019, 16Flash, 32Flash, 256RAM, 3port, GigabitEthernet, 802.11abgnac, 1USB, USB3.0, DevBoard, 1SIM, minipciexpress, 4core, arm, armv7 This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies ipq40xx ipq4019 16flash 32flash 256ram 3port gigabitethernet 802.11abgnac 1usb usb3.0 devboard 1SIM minipciexpress 4core arm armv7 Last modified: 2021/06/05 13:40by danitool