NETGEAR WAX206

The NETGEAR WAX206 is a WiFi 6, AX3200, dual band, dual core, Wireless Access Point/router.

netgear-wax206-rear_case.jpeg

It is not possible to force 2500Mbps negotiation via ethtool at the moment. In my testing, the auto-negotiation worked fine to bring the link up at 2500Mbps and I could manually force this link down to 1000Mbps with ethtool.

Installation from stock firmware is as simple as uploading the OpenWrt ...factory.img via the stock firmware updater (Advanced→Administration→Firmware Update).

The stock firmware will throw an error message warning that the new firmware is older, click Okay to continue. Then click Yes to upload. After reboot OpenWrt will be installed.

Specific values needed for tftp

Bootloader tftp server IPv4 address 192.168.1.10
Bootloader MAC address (special) N/A
Firmware tftp image Latest OpenWrt release (NOTE: Name must have a .img file suffix)
TFTP transfer window unknown
TFTP window start Wait for the Power LED to start flashing
TFTP client required IP address 192.168.1.1

See https://kb.netgear.com/000059633/How-do-I-upload-firmware-to-my-NETGEAR-router-using-a-TFTP-client-on-Microsoft-Windows for more info.

U-Boot allows booting an initramfs image via TFTP as follows:

setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm

nmrpflash can be used to TFTP without opening the case.

Info

Architecture Ralink ARM
Vendor MediaTek
Bootloader U-Boot
System-On-Chip MediaTek MT7622BV - ARM Cortex-A53
CPU/Speed 1.35GHz (Dual Core)
Flash-Chip Toshiba TC58CVG1S3HRAIJ
Flash size 256 MiB
RAM 512 MiB
Wireless 1 MediaTek MT7622BV - 802.11bgn (2.4GHz) 4×4 MIMO
Wireless 2 MediaTek MT7975AN - 802.11a/n/ac/ax (5GHz) 4×4 MIMO
Ethernet Lan 4 x 1000M MT7531AE
Ethernet Wan 1 x 2500M RTL8221B
Switch MediaTek MT7531AE
USB None
Serial Yes
JTAG Does not appear to be exposed
dev: size erasesize name
mtd0: 00080000 00020000 “Preloader”
mtd1: 00040000 00020000 “ATF”
mtd2: 00080000 00020000 “Bootloader”
mtd3: 00080000 00020000 “Config”
mtd4: 00100000 00020000 “Factory”
mtd5: 02600000 00020000 “ImageA”
mtd6: 025e0000 00020000 “Kernel”
mtd7: 002a0000 00020000 “kernel”
mtd8: 02340000 00020000 “rootfs”
mtd9: 00c60000 00020000 “rootfs_var”
mtd10: 02600000 00020000 “Kernel_backup”
mtd11: 00800000 00020000 “CFG”
mtd12: 00400000 00020000 “RAE”
mtd13: 00100000 00020000 “POT”
mtd14: 00400000 00020000 “Language”
mtd15: 00200000 00020000 “Traffic”
mtd16: 00100000 00020000 “Cert”
mtd17: 00100000 00020000 “NTGRcryptK”
mtd18: 00500000 00020000 “NTGRcryptD”
mtd19: 00100000 00020000 “LOG”
mtd20: 00640000 00020000 “User_data”

Measured with Peaktech P9035 (CS5460A-BSZ) at the wall power plug, the device consumes 6.6W with both WiFis active and three 1 Gigabit Ethernet links established without much traffic. Power consumption increases by 0.2W when changing scaling governor from ondemand (Idle with 437.5 MHz) to performance (Idle with 1350 MHz). Peak power consumption of about 10W has been seen loading the device with 50 Mbit/s OpenVPN traffic via Wifi, which loads one CPU core about 30%.

netgear_wax206_pcb_top.jpg netgear_wax206_pcb_bottom.jpg

Note that the right side panel cannot be removed without removing the pcb mounting screws (internal access)!

To open the case, the bottom stand must first be removed, there are two screws holding it on. These screws will prevent the left side panel from being removed. Next pry the left side panel free. This panel is held to the main body with plastic clips, I used a plastic pry bar around all the edges and shims to prevent re-latching while working.

port.serial general information about the serial port, serial port cable, etc.

Serial Port Pin-out from bottom of pcb, can be solder without removing the pcb from case:

Top side of the PCB has silkscreen markings for serial port. Reminder: don't connect vcc.

Serial connection parameters
for NETGEAR WAX206
115200, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

JTag is not exposed on the PCB.

F0: 102B 0000 F6: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 0000 0041 [0000] G0: 0190 0000 T0: 0000 036E [000F] Jump to BL UNIVPLL_CON0 = 0xFE000000!!! mt_pll_imt_pll_post_init: mt_get_cpu_freq = 1350000Khz 2 [EMI] DRAMC calibration start EMI]rank size auto detect [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987 [EMI]start_addr[0x40000[MEM] complex R/W mem test pass RAM_CONSOLE wdt status (0x0)=0x0 id: 98 EB [BBT] BMT.v2 is found at 0x7FF [PLFM] Init Boot Device: OK(0) [PART] blksz: 2048B [PART] [0x0000000000000000-0x0000000 [PART] load "lk" from 0x00000000art_load_images ret=0x0 [BLDR] Others, jump to ATF [BLDR] jump to 0x41E00000 [BLDR] <0x41E00000>=0xEA00000F [BLDR] <NAND: mt7531: mt7531_sw_init mt7531: mt7531_core_pll_setup, hwstrap = 000000ff, xtal=25MHz mt7531: mt7531_mac_port_setup, port = 6 mt7531: mt7531_set_portmt7531: timeout waiting for SGMII_LINK mt7531: mt7531_mac_port_setup, PMCR6 = f805633b >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: -------- gephy-calbration (port:0) -------- CALDLY = 40 GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (10) (0x32)(0xb2) GE R50 AnaCal Done! (10) (0x32)(0xb2) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE 1e_174(0xb1b2), 1e_175(0xb2b1) 2322 GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320 GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x2302 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1b1b) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x252d) PORT 0 RX_DC_OFFSET before pairA output = 1d after pairA output = ff before pairB output = 1e after pairB output = ff before pairC output = 1e after pairC output = 1 b GE R50 AnaCal Done! (13) (0x26)(0xa6) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (12) (0x30)(0xb0) GE 1e_174(0xa6b1), 1e_175(0xb1b0) GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120 GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2121 GE Tx offset A GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1e26) PORT 1 RX_DC_OFFSET NAND read: device 0 offset 0x28c0000, size 0x2600000 39845888 bytes read: OK image tag: MTD_IMAGEA_TAG image size: 0x1a40000 checksum: 0xed521903 image crc: 0xed521903 bootm flag=0, states=70f * kernel: default imageha1 from FIT Image at 4009ff28 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM64 Op Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4031bcf4 NAND read: device 0 offset 0x2c0 39845888 bytes read: OK image tag: MTD_image size: 0x1980000 checksum: 0xcc5ebf8b image crc: 0xcc5ebf8b bootm flag=0, states=70f * kernel: default image load address = 0x4009ff28 ## Load+ sha1+ OK ## Loading fdt from FIT Image at 4009ff28 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage De5cc10574c741d5c74 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4031bd70 Uncompressi00, end 5cf4ff3f ... OK Starting kernel ... [ATF][ 26.628098]save kernel info [ATF][ 26.631035]Kernel_EL2 [ATF][ thod from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. oftware IO TLB: mapped [mem 0x5fcf4000-0x5fdf4000] (1MB)Ds [ 0.000000] Memory: 497384K/524096K available (5092K kernel code, 0xffffffbffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB) [ 0.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795=50000) [ 0.000277] pid_max: default: 32768 minimum: 301 [ 0.000326] Mount-cache hash table entries: 1024 (order: 1, 81 [ 0.032117] Invalid sched_group_energy for CPU1 [ 0.032119] CPU1: update cpu_capacity 1024 [ 0.032121] CPU1: Booteroup_energy for Cluster1 [ 0.032274] Invalid sched_group_energy for CPU0 [ 0.032278] Invalid sched_group_energy for Clu] spm_irq_0 = 6, spm_irq_1 = 7 [ 0.038084] [SPM] spm_irq_2 = 8, spm_irq_3 = 9 [ 0.038087] [SPM] set spm as wakeup devci:2 [ 0.052433] [SLP] SLEEP_DPIDLE_EN:1, REPLACE_DEF_WAKESRC:0, SUSPEND_LOG_EN:1 [ 0.082107] vgaarb: loaded [ 0.0823 2 [ 0.092147] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.092178] TCP bind hash table entriesflags 0x0] [ 0.120472] pci_bus 0001:00: root bus resource [mem 0x20000000-0x27ffffff] [ 0.120479] pci_bus 0001:00: root 0.129251] pci 0001:00:00.0: BAR 0: no space for [mem size 0xffffffff 64bit pref] [ 0.129258] pci 0001:00:00.0: BAR 0: fai0:pcie01: service driver pcie_pme loaded [ 0.230791] mtk-pcie 1a145000.pcie: Port1 link down [ 0.230959] mtk-pcie 1a145abled [ 0.256640] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 232, base_baud = 1562500) is a ST16650V2 [ 1.128891] 1.209494] dump_power_table[7] = { .cpufreq_khz = 600000, .cpufreq_ncpu = 2, .cpufreq_power = 376 } [ 1.218624] dump_power = 2, .cpufreq_power = 225 } [ 1.255486] dump_power_table[12] = { .cpufreq_khz = 812500, .cpufreq_ncpu = 1, .cpufreq_power 0 [ 1.297506] [cal] calefuse2 = 0x4cc010 [ 1.301255] [cal] g_adc_ge_t = 0x295 [ 1.387961] Recognize NAND: ID [x202 [ 1.391041] 98 eb [ 1.393053] ], [TC58CVG1S3HRAIJ], Page[2048]B, Spare [128]B Tota[ 1.529632] 0x0000002e0000-0x00[ 1.592209] 2 fit-fw partitions found on MTD device Kernel [ 1.597695] 0x0000002e0000-0x000000580000 : "kernel" [ 1.606781] 0x000000580000-0x0000028c0000 : "rootfs"[ 1.661307] mtd: device 8 (rootfs) set to be root filesystem [ 1.728092] 0x0000028c0000-0x000004ec0000 : "Kernel_backup" [ 1.788939] 0x000004ec0000-0x0000056c0000 : "CFG" [ 1.815995] 0x000005ac0000-0x000005bc0000 : "POT" [ 1.822589] 0x000005bc0000-0x000005fc0000 : "Language" [ 1.833880][ 1.897427] mtdoops: ready 0, 1 (no erase) [ 1.901522] mtdoops: Attached to MTD device 19 [ 1.906290] 0x0000069c0000-0x000007000000 : "User_data" [ 1.920689] mtk-snand[ 2.793261] libphy: mdio: probed [ 2.796507] mtk_soc_eth 1b100000.ethernet: generated random MAC address ee:10:6c:4e:58:[ 3.801119] mtk_soc_eth 1b100000.ethernet: path gmac1_sgmii in set_mux_gdm1_to_gmac1_esw updated = 1 [ 3.810253] mtk_soc't present on the SoC [ 3.837391] mtk_soc_eth 1b100000.ethernet: RTL822x init success! [ 3.837476] .................................................................................................................................................................................................... [ 4.218084] load uc2 ramcode com...............................................................................................................................................................................! [ 4.479005] pkt_redirect_init complete [ 4.482835] nf_conntrack version 0.ort v1.8 [ 4.521535] registered taskstats version 1 [ 5.065429] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1 [ 5.075937] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz [ 5.347680] random: nonblocking pool is initialized [ 7.086516] mt753x gsw@0: PHY is Realtek 822x, attach its IRQ [ 7.092292] mt753x gsw@0: IRQ 93 attached! [ 7.096451][ 7.355496] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: [ 7.363681] mt753x gsw@0: -------- gephy-calb[ 7.452591] 0x1e-e0 = 2929 [ 7.457304] 0x1f-115 = 5 [ 7.459828] GE Rext AnaCal Done! (9)(0x29) [ 7.538681] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 7.606948] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 7.675208] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 7.748728] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 7.757048] GE 1e_174(0xb1b2), 1e_175(0xb2b1) [ 7.804834] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 7.837865] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2222 [ 7.876347] GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320 [ 7.904303] GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x2302 [ 7.990477] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) [ 8.047202] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1b1b) [ 8.121238] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1d25) [ 8.241672] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x252d) [ 8.295406] PORT 0 RX_DC_OFFSET [ 8.309712] before pairA output = 1d [ 8.315365] after pairA output = ff [ 8.320843] before pairB output = 1e [ 8.[ 8.451936] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 8.525634] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 8.599159] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 8.677971] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 8.686289] GE 1e_174(0xa6b1), 1e_175(0xb1b0) [ 8.728764] GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120 [ 8.756560] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2121 [ 8.794860] GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320 [ 8.927677] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d) [ 9.036423] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2424) [ 9.109777] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1e26) [ 9.156855] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x141c) [ 9.210139] PORT 1 RX_DC_OFFSET [ 9.224317] before pairA output = 1d [ 9.229948] after pairA output = ff [ 9.235413] before pairB output = 1c [ 9.241046] after [ 9.354866] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 9.428889] GE R50 A[ 9.502835] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 9.571090] GE R50 AnaCal Done! (10[ 9.643013] GE Tx offset AnaCal Done! (pair-0)(6)(0x25) 0x1e_172=0x2520 fset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2522 8] GE Tx offset AnaCal Done! (pair-2)(6)(0x25) 0x1e_173=0x2520 [ 9.747408] GE Tx offset AnaCal Done! (pair-3)(1)(0x1) 0x1e_173=0x2501 [ 9.832860] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6c1b) [ 9.882433] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1a1a) [ 10.009495] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1921) 76984] before pairA output = f [ 10.082526] after pairA output = ff [ 10.087985] before pairB output = 1e [ 10.093615][ 10.212983] GE R50 AnaCal Done! (12) (0x30)(0xb0) 0 AnaCal Done! (10) (0x32)(0xb2) [ 10.428284] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 10.436612] GE 1e_174(0xb0b2), 1e_175(0xb1b1) [ 10.484337] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 10.506829] GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2201 [ 10.534492] GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 ! (pair-3)(3)(0x22) 0x1e_173=0x2122 [ 10.735547] GE Tx[ 10.769511] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1921) [ 10.876377] PORT 3 RX_DC_OFFSET [ 10.890558] before pairA output = f [ 10.896099] after pairA output = ff [ 10.901565] before pairB output = e [ 10.907105] after p[ 11.094531] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 11.157475] GE R50 AnaCal Done! (9) (0x34)(0xb4[ 11.225630] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 11.233952] GE 1e_174(0xb1b1), 1e_175(0xb4b2) [ 11.281688] GE Tx offset AnaCal Done! (pair-0)(3)(0x3) 0x1e_172=0x320 [ 11.325139] GE Tx offset AnaCal Done! (pair-1)(5)(0x24) 0x1e_172=0x324 [ 11.380412] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x103 [ 11.529422] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1212) ne! (pair-2)(1e_19 = 0x171f) [ 11.630241] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x121a) [ 11.683538] PORT 4 RX_DC_OFFSET [ 11.697731]90] regulator regulator.3: info->modeset_reg 0xc = 0x101c32a2 [ 11.775317] VFS: Mounted root (squashfs filesystem) readonly [ 12.547971] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 13.073835] jffs2: notice: (843) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 13.260303] jffs2: notice: (865) jffs2_build_xattr_subsystem: complt Set 3 port Check 1 port Phy read reg=0x1, value=0x1c0 Phy read reg=0x7, value=0x3c0 Phy read reg=0x4, value=0x209 Phy read reg=0xa Phy read reg=0x4, value=0x209 Phy read reg=0xa, value=0xc 7531 need modify collision reg! Write reg=30e0, value=203f ARNING: Variable 'lan' does not exist or is not an array/object Press the [f] key and hit [enter] to enter failsa[ 20.136458] mount_root: mounting /dev/root [ 20.142155] mount_root: loading kmods from internal overlay [ 20.323847] block: attempting to load /etc/config/fstab [ 21.628988] Netfilter messages via NETLINK v0e is -0000 [ 21.652069] mtk_eth_api_init [ 21.654994] Init mtk_eth_api Driver Module....OK [ 22.752460] register mt_drv [ 22.755714] mt_drv 0001:01:00.0: enabling device (0000 -> 0002) [ 22.769518] [ 22.769518] [ 22.769518] === pAd = fffffdev_init(caller:RTMP_COM_IoctlHandle+0x340/0x16b0 [mt_wifi]), wdev(0) [ 22.815462] Rx[0] Ring: total 24576 bytes allocated [ 23.244886] register mt_drv [ 23.252056] [ 23.252056] == pAd = ffffff800ad01000, size = 6964992, Status=0 == [ 23. 2.4.2 [ 23.300279] PPP MPPE Compression module registered [ 23.305929] NET: Registered protocol family 24 [ 23.311500mirror_probe(): hif_cfg base addr=ffffff8009798400 [ 23.354308] kmodloader: done loading kernel modules from /etc/modules.d/[ 24.028601] [mtfwd] update eth interface eth0 [ 28.687689] APWdsInitialize():WdsEntry Number=4 [ 28.693348] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT286rametersPower Boost (VHT40): RTMPSetProfileParametersPower Boost (VHT80): RTMPSetProfileParametersPower Boost (VHT160): RTMPSet[ 28.85 [ 28.866461] APWdsInitialize():WdsEntry Number=4 [ 28.871086] WDS-Enable mode= 28.933624] ICapMode = 0 [ 28.940643] WtcSetMaxStaNum: BssidNum:3, MaxStaNum:123 (WdsNum:4, ApcliNum:1, MaxNumChipRept:16) [ 29.080881] ctl->tx_doneq = ffffff800b36aee8 [ 29.097105] ctl->rx_doneq = ffffff800b36af00 [ 29.101516] mt_rbus 0000:00:00.0: Direct firmware load for mt7622_patch_e2_[ 29.125110] Parsing patch header [ 29.128333] Built date: 20200821025910a [ 29.132333] [ 29.141106] Platform: AL[ 29.185146] EventGenericEventHandler: CMD Success [ 29.190395] MtCmdPatchFinishReq [ 29.204797] EventGenericEventHandler: CMD Success [ 29.209558] release patch semaphore [ 29.213043] WfMcuHwInit: Before NICLoadFirmware, che2] Feature set: 0x01 [ 29.284164] Target address: 0xb7000, Download size: 249856 [ 29.297103] Parsing tailer region 1 et address: 0x203dc00, Download size: 50272 [ 29.329152] EventGenericEventHandler: CMD Success [ 29.337921] EventGenericEler: CMD Success [ 29.394612] MCU Init Done! [ 29.397322] efuse_probe: efuse = 2 [ 29.400717] RtmpChipOpsEepromHook::ex52 bb00 [ 29.463004] mt7622_pa_lna_set(): read antCtrl = 0, polCtrl = 4, wifiStreams = 44 [ 33.068440] Country Region from e2p = 0 [ 33.072303] read sub id = 2 [ 33.075110] NICReadEEPROMParameters:FeLossComp = (0x0 0x0 0x0 ioCtrl=ffffffc0184891d8,Band=0,rfcap=1,channel=1,PhyMode=2 extCha=0xf [ 33.119096] MtSingleSkuLoadParam: RF_LOCKDOWN FeatureBfBackOffLoadParam: RF_LOCKDOWN Feature OFF !!! [ 33.143835] EEPROM Init Done! [ 33.146819] mt_mac_init()--> [ 33.1497[ 33.176446] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 33.193509] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 33.210570] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 33.217104] MAC IModuleEnCtrl:It's not DBDC mode [ 33.262266] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 [ 33.267262] MtCmdEDCCACtrl: BandIdtal allocated 4 WDS interfaces! [ 33.311020] WtcSetMaxStaNum: BssidNum:3, MaxStaNum:123 (WdsNum:4, ApcliNum:1, MaxNumChipRep[ 33.349220] RedInit: set Driver/N9 RED Enable to 1. [ 33.354196] RedInit: RED Initiailize Done. [ 33.358362] cp_support_is_enabled: setdjust : no prim_ch value for adjust! [ 33.398287] Caller: wlan_operate_init+0xdc/0x118 [mt7622_mt_wifi] [ 33.404473] phy_ApAutoChannelAtBootUp-----------------> [ 33.454053] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 [ 33.459932] MtCmdSe[ 33.523371] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=1, SwChCfg.BandIdx=0 nnelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 [ 33.742642] BW = 0,TXStream = 4, RXStream = switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=2, SwChCfg.BandIdx=0 [ 33.985231] MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 33.994290] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 34.027506] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=3, SwChCfg.BandIdx=0 [ 34.237267] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 [ 34.246410] BW = 0,TXStream = 4, RXStream = 4,h_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=4, SwChCfg.BandIdx=0 2=0, central_chl = 5 DBDCIdx= 0, Band= 0 [ 34.498251] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 34.531523] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=5, SwChCfg.BandIdx=0 [ 34.741188] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 34.750250] BW = 0,TXStream = 4, RXStream = 4, sc[ 34.783482] mt7622_s[ 34.993235] MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 [ 35.002410] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.035607] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=7, SwChCfg.BandIdx=0 [ 35.245172] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 [ 35.254388] BW = 0,TXStream = 4, RXStream = 4, scan[ 35.287682] mt7622_switch_chann[ 35.497184] MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 [ 35.506224] BW = 0,TX[ 35.733205] MtCmdChannelSwitctch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=10, SwChCfg.BandIdx=0 ol_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 [ 35.978470] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.995813] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=11, SwChCfg.BandIdx=0 ================================================ [ 36.212740] Channel 1 : Busy Time = 7987, Skip Channel = FALSE, BwCap l 6 : Busy Time = 18552, Skip Channel = FALSE, BwCap = TRUE [ 36.257814] Channel 7 : Busy Time = 7298, Skip Channel =295406] ==================================================================== [ 36.302873] Rule 3 Channel Busy time value : Sl for wdev for this band PhyMode = 14, Channel = 8 [ 36.344980] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, centr[ 36.387302] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=6, SwChCfg.BandIdx=0 [ 36.397286] ApAutdx = 0, LinkToWdevType = 1 [ 36.543038] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 [ 36.548803] APStartUpForMbss: BssIndex = 0 channel = 8 [ 0 [ 36.596776] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.641767] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=1, SwChCfg.BandIdx=0 [ 36.651453] A[ 36.953121] MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 [ 36.962105] BW = 0,TXStream = 4, RXSt[ 36.995176] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=2, SwChCfg.BandIdx=0 [ 37.004860] AP OBSS SYNC - [ 37.309126] MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 37.318087] BW = 0,TXS[ 37.351161] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=3, SwChCfg.BandIdx=0 [ 37.360840] A[ 37.665118] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 [ 37.674081] BW = 0,TX[ 37.707146] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=4, SwChCfg.BandIdx=0 [ 37.716855] A[ [ 38.377119] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 38.386080] BW = 0,TX 38.419148] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=6, SwChCfg.BandIdx=0 [ 38.428856] AP[ 38.775226] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=7, SwChCfg.BandIdx=0 [ 38.784912] A[ 39[ 39.445148] MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 [ 39.454109] BW = 0,TX[ 39.785119] MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 [ 39.794256] BW = 0,[ 39.811539] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=10, SwChCfg.BandIdx=0 [ 39.821357] [ 40.125130] MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 [ 40.134278] BW = 0,[ 40.465118] Channel[Idx=0, Ch=1].bEffectedChannel=0x2! [ 40.470258] needFallBack=TRUE due to OP/OT! [ 40.474439] Chann [ 40.508498] needFallBack=TRUE due to OS! [ 40.512419] Channel[Idx=6, Ch=7].bEffectedChannel=0x0! [ 40.517554] Channe[ 40.601022] mt7622_switch_channel():SwChCfg.Channel_Band = 0, SwChCfg.CentralChannel=6, SwChCfg.BandIdx=0 [ 40.610721] a: c8:9e:43:fd:d5:b5 was aleady existed. [ 40.664525] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 40.67142 [ 40.712448] wed_init(0): irq=13,base_addr=0xffffff800b85e000 [ 40.719392] wed_ring_init(): wed ring init result = 0 [ 40.741231] create wed ok!!! [ 40.744291] wdma_init(): wdma(0) base addr=ffffff800b970800 [ 40.750907] wdma_init(): wd20a000.wed2 failed with error -1 [ 40.794751] mt_service_open: wlan service opens successfully! [ 40.803553] APWdsInitial41882] cfg_mode=17 [ 40.844329] cfg_mode=17 [ 40.847749] Final: Apcli0, PhyMode=177 [ 40.851571] Final: Apcli1, PhyMod APEdca0 [ 40.939813] APEdca1 [ 40.942830] APEdca2 [ 40.945093] APEdca3 [ 40.949681] UAPSDCapable[0]=1 [ 40.952640.987278] UAPSDCapable[12]=1 [ 40.990377] UAPSDCapable[13]=1 [ 40.993708] UAPSDCapable[14]=1 [ 40.996764] UAPSDCapabl = 1 [ 41.083625] read_itxbf: More BSSID[1] [ 41.088017] read_itxbf: More MBSS[1] ITxBfEn = 1 [ 41.093294] read_itxbf:apidx=1, Desired PMFSHA256=0 [ 41.259922] [PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0 ode=01.267020] MAP_MODE=0 [ 41.306793] If/wds0 - PeerPhyMode=0xb1 [ 41.312385] HT_BAWinSize: wdev[0]: (TX=256, RX=256) [ 41.317586] HT: WD[ 41.423443] rtmp_read_mlme_multiqueue_parms_from_file(): [hp_q_ration]-[np_q_ration]-[lp_q_ration] = 8-4-1 [ 41.439459] W048! [ 41.541662] -->TX_RING_1[0xd7310]: Attr:0, Base=0x59978000, Cnt=2048! [ 41.548166] -->TX_RING_2[0xd5400]: Attr:3, Bch header [ 41.639253] Built date: 20201105222230a [ 41.643567] [ 41.645095] Platform: ALPS [ 41.647990] HW/SW 0x13720 [ 41.684949] Patch SEM Status = 2 [ 41.689174] patch is not ready && get semaphore success [ 41.694433] StartatchFinishReq [ 41.740780] EventGenericEventHandler: CMD Success [ 41.745712] Patch SEM Status = 3 [ 41.748969] releas Target address: 0x31dc00 [ 41.850837] Download size: 205824 [ 41.854713] Feature set: 0x00 [ 41.858769] Parsing taze: 0x0 [ 41.947626] Decomp block size: 0x0 [ 41.951243] Target address: 0x23ac00 [ 41.954953] Download size: 870401.990520] tag 1, padding length = 3, tag length = 61 [ 41.995969] payload: t-neptune-main-mt7915-1953-MT7915D_1953_MT7621-icEventHandler: CMD Success [ 42.091298] MtCmdAddressLenReq:(ret = 0) [ 42.097407] Start address = 0x23ac00, DL length = Decomp size: 0x0 [ 42.185832] Decomp block size: 0x0 [ 42.189352] Target address: 0x10200000 [ 42.193218] Download ecomp crc: 0x0 [ 42.229614] Decomp size: 0x0 [ 42.232578] Decomp block size: 0x0 [ 42.236107] Target address: 0xe00, DL length = 19392, Data mode = 0x80000010 [ 42.278733] EventGenericEventHandler: CMD Success [ 42.283465] MtCmdAddressL131072] [ 42.458427] [EEPROMImage - PreCalImageInfo - PreCalImage - TxDPDImage] [ 42.458427] [0xffffffc01[ 42.520524] [a-die version:2] [ 47.900634] Country Region from e2p = 0 [ 47.904487] antenna_default_reset() todo [ 47.908409] antenna_default_reset() value = 0x2424, TxPath = 4, RxPath mdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 48.005673] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status TxBfModuleEnCtrl:It's not DBDC mode [ 48.096288] CmdHeraStbcPriorityCtrl: u1BandIdx=0, u1Operation=1, u1StbcPriority=0 [ 0]!! [ 48.136768] [set_datcfg_ack_cts_timeout](10964): DAT config band(0) ofdma_timeout Fail! [ 48.144766] CTS/ACK Timeou_datcfg_ack_cts_timeout](10964): DAT config band(1) ofdma_timeout Fail! [ 48.185749] MtCmdSetVht1024QamSupport: Vht1024QamSu224811] wdev_init(caller:MSTA_Init+0x33c/0x5b0 [mt_wifi]), wdev(3) [ 48.231685] Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ [ 48.402212] RedInit: set CR4/N9 RED Enable to 1. [ 48.406908] RedInit: RED Initiailize Done. [ 48.411436] cp_support_is_enabled: set CR4 CP_SUPPORT t48.493259] hw_ctrl_flow_v2_open: wdev_idx=0 [ 48.497789] AP inf up for ra_0(func_idx) OmacIdx=0 [ 48.502692] AsicRadioOnO[ 48.574525] MtCmdSetTxRxPath: ctrl_chl=36, ctrl_ch2=0, cent_ch=36, RxPath=f, BandIdx=0, ChBand=1, BW=0,TXStream=4, RXStream=[ 48.789568] mt7915_apply_dpd_f[ 48.823988] MtCmdSetl [ 49.049613] MtCmdChannelSwitch: ctrl_[ 49.076679] MtCmdSetTxRxPath: ctrl_chl=44, ctrl_ch2=0, cent_ch=44, RxPath=f, BandIdx=0, ChBand=1, BW=0,TXStream=4, RXStream=[ 49.29349[ 49.327741] MtCmdSetTxRxPathl [ 49.551390] MtCmdChannelSwitch: ctrl_chl=149, ctrl_ch2=0, cent_ch=149 DBDCIdx=0, ChB[ 49.793472] mt7915_appl 49.827378] MtCmdSetTxRxPath: ctrl_chl=153, ctrl_ch2=0, cent_ch=153, RxPath=f, BandIdx=0, ChBand=l [ 50.049062] MtCmdChannelSwitch: ctrl_chl=157, ctrl_ch2=0, cent_ch=157 DBDCId_data: eeprom 0x62 bit 0 is 0, do runtime cal [ 50.297095] MtCmdChannelSwitch: ctrl_chl=161, ctrl_ch2=0, cent_ch=161 DBDCIdx[ 50.537614] UpdateBeaconHandler, wdewCap = TRUE [ 50.585393] Channel 149 : Busy Time = 1825, Skip Channel = FALSE, BwCap = TRUE [ 50.592791] Channel 153 : mary Channel 161 [ 50.628986] Rule 3 Channel Busy time value : Min Channel Busy = 4894 [ 50.635340] Rule 3 Channel Busy t[ PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE [ 50.949374] Caller: dump_ht_cap+0x10/0x20 [mt_54] ap_link_up(caller:wdev_do_linkup+0x1c/0x30 [mt_wifi]), wdev(0) [ 50.992058] wifi_sys_linkup, wdev idx = 0 1.162825] set muru_update_he_cfg()!!!! [ 51.166752] PrintSrCmd: [ 51.166752] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0,u1StaIdx = 0, u4Value = 1 [ 51.208900] PrintSrCmd: [ 51.208900] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = [ 51.298444] br-lan: port 1(eth0.0) entered forwarding state [ 51.599105] device ra0 entered promiscuous modearding state [ 51.633329] br-lan: port 2(ra0) entered forwarding state [ 51.638680] br-lan: port 2(ra0) entered forwarding state romiscuous mode [ 51.725249] br-lan: port 3(rai0) entered forwarding state [ 51.730740] br-lan: port 3(rai0) entered forwarding state [ 52.139537] no net device found for eth0 or [ 52.144001] no net device found for rax0 or apclix0 [ 52.151634] no net ound for apclix0 [ 52.204569] [ 52.250387] Mac: c8:9e:43:fd:d5:b6 was aleady existed. [ 52.255758] Mac: c8:9e:43:fd:d5:b5 was aleady existed. [ 52.269822] Mac: c8:9e:43:fd:d5:b5 was alead[ 52.305330] Mac: c8:9e:43:fd:d5:b5 was aleady existed. [ 52.313336] Mac: c8:9e:43:fd:d5:b5 was aleady existed. [ 52.32[ 52.893367] sh (7702): drop_caches: 3 [ 53.305145] br-lan: port 1(eth0.0) entered forwarding state ****************Start of ping-netgear******************** [ 53.641148] br-lan: port 2(ra0) entered forwarding state [ 53.954632] Disable GAS service for MBSSID[0] [ 53.9605_cmm_ie: Unknown IE(EID = 111) [ 54.010882] set_wapp_cmm_ie: Unknown IE(EID = 110) [ 54.268119] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 [ 54.366793] Set_Fh_Bss_[ 54.407914] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 [ 59.208717] module exit [ 59.512236] Set_MapR[ 59.586542] set_thermal_protection_admin_ctrl_duty_proc: u4Lv0Duty: 100, u4Lv1Duty: 90, u4Lv2Duty: 80, u4Lv3Duty: 60 [ 59.604155] set_thermal_protect[ 59.654854] SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 0, duty: 100 [ 59.661951] MtCmdThermalProtectDutyCfg: ban04124] MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 2 [ 59.710282] MtCmdThermalProtectDutyCfg: duty: 80 [ 59.71832: trigger_temp: 122, restore_temp: 116, recheck_time: 60 [ 59.811069] MtCmdThermalProtectEnable: band_idx: 0, protect_type: hermalProtectEnable: band_idx: 0, protect_type: 2 [ 59.858154] MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 125 Login timed out WAX206 login: WAX206 login:


Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.000000] Linux version 5.15.80 (jason@openwrt-build) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r21168+6-c3322cf04a) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Dec 2 13:23:29 2022 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Machine model: Netgear WAX206 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] printk: bootconsole [uart8250] enabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Zone ranges: Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] DMA32 empty Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Normal empty Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Movable zone start for each node Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Early memory node ranges Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] psci: probing for conduit method from DT. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] psci: PSCIv0.2 detected in firmware. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] psci: Using standard PSCI v0.2 function IDs Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] psci: Trusted OS migration not required Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: s29592 r8192 d31848 u69632 alloc=17*4096 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Detected VIPT I-cache on CPU0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] CPU features: detected: ARM erratum 843419 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] CPU features: detected: ARM erratum 845719 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Memory: 501608K/524288K available (8192K kernel code, 886K rwdata, 2164K rodata, 384K init, 291K bss, 22680K reserved, 0K cma-reserved) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] rcu: Hierarchical RCU implementation. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Tracing variant of Tasks RCU enabled. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] Root IRQ handler: gic_handle_irq Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] GIC: Using split EOI/Deactivate mode Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys). Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.000000] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.008256] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.018654] pid_max: default: 32768 minimum: 301 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.023371] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.030715] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.039588] rcu: Hierarchical SRCU implementation. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.044526] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.052446] smp: Bringing up secondary CPUs ... Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.057351] Detected VIPT I-cache on CPU1 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.057399] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.057458] smp: Brought up 1 node, 2 CPUs Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.072137] SMP: Total of 2 processors activated. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.076853] CPU features: detected: 32-bit EL0 Support Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.082009] CPU features: detected: CRC32 instructions Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.087252] CPU: All CPU(s) started at EL2 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.091364] alternatives: patching kernel code Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.099252] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.109154] futex hash table entries: 512 (order: 3, 32768 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.116065] pinctrl core: initialized pinctrl subsystem Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.121885] NET: Registered PF_NETLINK/PF_ROUTE protocol family Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.128055] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.135161] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.142954] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.151126] thermal_sys: Registered thermal governor 'fair_share' Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.151129] thermal_sys: Registered thermal governor 'bang_bang' Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.157241] thermal_sys: Registered thermal governor 'step_wise' Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.163271] thermal_sys: Registered thermal governor 'user_space' Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.169462] ASID allocator initialised with 65536 entries Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.181291] pstore: Registered ramoops as persistent store backend Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.187497] ramoops: using 0x10000@0x42ff0000, ecc: 0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.211980] cryptd: max_cpu_qlen set to 1000 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.218131] SCSI subsystem initialized Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 0.221994] libata version 3.00 loaded. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.226776] clocksource: Switched to clocksource arch_sys_counter Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.233341] NET: Registered PF_INET protocol family Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.238334] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.245942] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.254340] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.262119] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.269923] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.277141] TCP: Hash tables configured (established 4096 bind 4096) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.283572] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.290138] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.297214] NET: Registered PF_UNIX/PF_LOCAL protocol family Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.302906] PCI: CLS 0 bytes, default 64 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.309126] workingset: timestamp_bits=46 max_order=17 bucket_order=0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.318253] squashfs: version 4.0 (2009/01/31) Phillip Lougher Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.324112] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.367969] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm" Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.379442] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.400364] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.407463] printk: console [ttyS0] disabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.431945] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 125, base_baud = 1562500) is a ST16650V2 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.441265] printk: console [ttyS0] enabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.449635] printk: bootconsole [uart8250] disabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.480061] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 126, base_baud = 1562500) is a ST16650V2 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.489942] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 130, base_baud = 17499995) is a MediaTek BTIF Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.499716] serial serial0: tty port ttyS2 registered Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.505316] mtk_rng 1020f000.rng: registered RNG driver Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.507050] random: crng init done Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.516331] loop: module loaded Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.519902] mtk-ecc 1100e000.ecc: probed Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.525899] spi-nand spi2.0: Toshiba SPI NAND was found. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.531245] spi-nand spi2.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.539462] mtk-snand 1100d000.spi: ECC strength: 12 bits per 512 bytes Fri Dec 2 13:26:40 2022 kern.info kernel: [ 0.547265] [BBT] BMT.v2 is found at 0x7ff Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.551574] 17 fixed-partitions partitions found on MTD device spi2.0 Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.558061] OF: Bad cell count for /spi@1100d000/flash@0/partitions Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.564341] OF: Bad cell count for /spi@1100d000/flash@0/partitions Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.570866] OF: Bad cell count for /spi@1100d000/flash@0/partitions Fri Dec 2 13:26:40 2022 kern.err kernel: [ 0.577146] OF: Bad cell count for /spi@1100d000/flash@0/partitions Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.583519] Creating 17 MTD partitions on "spi2.0": Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.588400] 0x000000000000-0x000000080000 : "Preloader" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.594646] 0x000000080000-0x0000000c0000 : "ATF" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.600104] 0x0000000c0000-0x000000140000 : "Bootloader" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.606321] 0x000000140000-0x0000001c0000 : "Config" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.612236] 0x0000001c0000-0x0000002c0000 : "Factory" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.618992] 0x0000002c0000-0x0000028c0000 : "firmware" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.675118] 2 fixed-partitions partitions found on MTD device firmware Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.681667] Creating 2 MTD partitions on "firmware": Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.686624] 0x000000000000-0x000000600000 : "kernel" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.691837] 0x000000600000-0x000002600000 : "ubi" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.696859] 0x0000028c0000-0x000004ec0000 : "firmware_backup" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.752891] 0x000004ec0000-0x0000056c0000 : "CFG" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.768062] 0x0000056c0000-0x000005ac0000 : "RAE" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.778119] 0x000005ac0000-0x000005bc0000 : "POT" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.784366] 0x000005bc0000-0x000005fc0000 : "Language" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.794879] 0x000005fc0000-0x0000061c0000 : "Traffic" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.802892] 0x0000061c0000-0x0000062c0000 : "Cert" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.809302] 0x0000062c0000-0x0000063c0000 : "NTGRcryptK" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.816184] 0x0000063c0000-0x0000068c0000 : "NTGRcryptD" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.828474] 0x0000068c0000-0x0000069c0000 : "LOG" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 0.834751] 0x0000069c0000-0x000007000000 : "User_data" Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.218254] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc0092a0000, irq 140 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.228090] i2c_dev: i2c /dev entries driver Fri Dec 2 13:26:40 2022 kern.err kernel: [ 1.233327] mtk-wdt 10212000.watchdog: IRQ index 0 not found Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.239141] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.248650] NET: Registered PF_INET6 protocol family Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.254512] Segment Routing with IPv6 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.258206] In-situ OAM (IOAM) with IPv6 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.262156] NET: Registered PF_PACKET protocol family Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.267304] 8021q: 802.1Q VLAN Support v1.8 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.272599] pstore: Using crash dump compression: deflate Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.287213] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges: Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.293765] mtk-pcie 1a143000.pcie: Parsing ranges property... Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.299618] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.443252] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.449482] pci_bus 0000:00: root bus resource [bus 00-ff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.454980] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff] Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.461882] pci_bus 0000:00: scanning bus Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.465963] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.472034] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref] Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.483303] pci_bus 0000:00: fixups for bus Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.487520] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.494230] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.502283] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.509193] pci_bus 0000:01: scanning bus Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.513446] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.519674] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.527038] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.534385] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.542439] pci 0000:01:00.0: supports D1 D2 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.546715] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.553379] pci 0000:01:00.0: PME# disabled Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.557922] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.600381] pci_bus 0000:01: fixups for bus Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.604580] pci_bus 0000:01: bus scan returning with max=01 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.610187] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.616848] pci_bus 0000:00: bus scan returning with max=01 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.622438] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.630092] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.638098] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.644882] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.652711] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.660539] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.668364] pci 0000:00:00.0: PCI bridge to [bus 01] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.673327] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.680231] pcieport 0000:00:00.0: assign IRQ: got 145 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.685373] pcieport 0000:00:00.0: enabling device (0000 -> 0002) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.691483] pcieport 0000:00:00.0: enabling bus mastering Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.696918] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44d9d0c0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.704294] pcieport 0000:00:00.0: PME: Signaling with IRQ 145 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.710199] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x325814c3) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.718380] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100006) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.726377] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0x6040000) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.734466] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10000) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.742380] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0xc) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.750038] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.757696] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0x40010100) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.765952] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0x4200000) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.774127] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x20102000) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.782392] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.790046] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.797700] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.805348] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.813002] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x50) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.820741] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.828394] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x20191) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.836838] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges: Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 1.843372] mtk-pcie 1a145000.pcie: Parsing ranges property... Fri Dec 2 13:26:40 2022 kern.info kernel: [ 1.849206] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.076835] mtk-pcie 1a145000.pcie: Port1 link down Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.081869] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.088064] pci_bus 0001:00: root bus resource [bus 00-ff] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.093551] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff] Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.100431] pci_bus 0001:00: scanning bus Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.106331] pci_bus 0001:00: fixups for bus Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.110514] pci_bus 0001:00: bus scan returning with max=00 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.116602] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.165511] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.172850] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.182496] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=146) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.202725] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=147) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.222449] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=148) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.242108] mt7530 mdio-bus:00 lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=149) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.406835] mt7530 mdio-bus:00 wan (uninitialized): PHY [mdio-bus:07] driver [RTL8221B-VB-CG 2.5Gbps PHY] (irq=POLL) Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.418354] DSA: tree 0 setup Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.422571] UBI: auto-attach mtd7 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.425908] ubi0: default fastmap pool size: 10 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.430452] ubi0: default fastmap WL pool size: 5 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.435147] ubi0: attaching mtd7 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.517030] ubi0: scanning is finished Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.524524] ubi0: attached mtd7 (name "ubi", size 32 MiB) Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.529951] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.536847] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.543633] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.550594] ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.556594] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.563818] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1669987409 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.572956] ubi0: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 39 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.582184] ubi0: background thread "ubi_bgt0d" started, PID 529 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.589179] block ubiblock0_0: created from ubi0:0(rootfs) Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 2.594664] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.605990] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.613313] Freeing unused kernel memory: 384K Fri Dec 2 13:26:40 2022 kern.info kernel: [ 2.646912] Run /sbin/init as init process Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.651014] with arguments: Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.653978] /sbin/init Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.656682] with environment: Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.659834] HOME=/ Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 2.662188] TERM=linux Fri Dec 2 13:26:40 2022 user.info kernel: [ 2.863641] init: Console is alive Fri Dec 2 13:26:40 2022 user.info kernel: [ 2.867179] init: - watchdog - Fri Dec 2 13:26:40 2022 user.info kernel: [ 3.185591] kmodloader: loading kernel modules from /etc/modules-boot.d/* Fri Dec 2 13:26:40 2022 user.info kernel: [ 3.203858] kmodloader: done loading kernel modules from /etc/modules-boot.d/* Fri Dec 2 13:26:40 2022 user.info kernel: [ 3.215919] init: - preinit - Fri Dec 2 13:26:40 2022 kern.info kernel: [ 3.503345] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode Fri Dec 2 13:26:40 2022 kern.info kernel: [ 3.511929] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx Fri Dec 2 13:26:40 2022 kern.info kernel: [ 3.521205] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode Fri Dec 2 13:26:40 2022 kern.info kernel: [ 5.444261] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx Fri Dec 2 13:26:40 2022 kern.info kernel: [ 5.451851] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.583863] UBIFS (ubi0:1): Mounting in unauthenticated mode Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.589630] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 616 Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.605666] UBIFS (ubi0:1): recovery needed Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.658241] UBIFS (ubi0:1): recovery completed Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.662773] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.670620] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.680548] UBIFS (ubi0:1): FS size: 16887808 bytes (16 MiB, 133 LEBs), max 143 LEBs, journal size 1015809 bytes (0 MiB, 7 LEBs) Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.692122] UBIFS (ubi0:1): reserved for root: 797652 bytes (778 KiB) Fri Dec 2 13:26:40 2022 kern.notice kernel: [ 5.698567] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 158F7CF8-E040-4366-998D-C046C07A7C1B, small LPT model Fri Dec 2 13:26:40 2022 user.info kernel: [ 5.712094] mount_root: switching to ubifs overlay Fri Dec 2 13:26:40 2022 kern.warn kernel: [ 5.719797] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. Fri Dec 2 13:26:40 2022 user.debug kernel: [ 5.733166] urandom-seed: Seeding with /etc/urandom.seed Fri Dec 2 13:26:40 2022 kern.info kernel: [ 5.806195] mt7530 mdio-bus:00 lan1: Link is Down Fri Dec 2 13:26:40 2022 user.info kernel: [ 5.814475] procd: - early - Fri Dec 2 13:26:40 2022 user.info kernel: [ 5.817472] procd: - watchdog - Fri Dec 2 13:26:40 2022 user.info kernel: [ 6.374596] procd: - watchdog - Fri Dec 2 13:26:40 2022 user.info kernel: [ 6.379168] procd: - ubus - Fri Dec 2 13:26:40 2022 user.info kernel: [ 6.435667] procd: - init - Fri Dec 2 13:26:40 2022 user.info kernel: [ 6.687915] urngd: v1.0.2 started. Fri Dec 2 13:26:40 2022 user.info kernel: [ 6.725287] kmodloader: loading kernel modules from /etc/modules.d/* Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.741464] GACT probability on Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.745195] Mirror/redirect action on Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.752664] u32 classifier Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.755379] input device check on Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.759065] Actions configured Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.766349] Loading modules backported from Linux version v5.15.74-0-ga3f2f5ac9d61 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.774016] Backport generated by backports.git v5.15.74-1-0-ge2d78967 Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 6.827908] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 6.839512] mt7915e 0000:01:00.0: assign IRQ: got 145 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.844639] mt7915e 0000:01:00.0: enabling device (0000 -> 0002) Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 6.850764] mt7915e 0000:01:00.0: enabling bus mastering Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.902254] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a Fri Dec 2 13:26:40 2022 kern.info kernel: [ 6.902254] Fri Dec 2 13:26:40 2022 kern.debug kernel: [ 6.984575] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44d9d0c0 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 7.003309] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 7.055419] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a Fri Dec 2 13:26:40 2022 kern.info kernel: [ 7.055419] Fri Dec 2 13:26:40 2022 kern.info kernel: [ 7.194222] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052 Fri Dec 2 13:26:40 2022 kern.info kernel: [ 7.252077] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111 Fri Dec 2 13:26:40 2022 user.info kernel: [ 7.409294] kmodloader: done loading kernel modules from /etc/modules.d/* Fri Dec 2 13:26:40 2022 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses! Fri Dec 2 13:26:40 2022 user.notice dnsmasq: Allowing 127.0.0.0/8 responses Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: started, version 2.87 cachesize 150 Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: DNS service limited to local subnets Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for test Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for onion Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for localhost Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for local Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for invalid Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for bind Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: using only locally-known addresses for lan Fri Dec 2 13:26:40 2022 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: read /etc/hosts - 4 addresses Fri Dec 2 13:26:40 2022 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 addresses Fri Dec 2 13:26:41 2022 daemon.notice wpa_supplicant[1469]: Successfully initialized wpa_supplicant Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: bonding Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: 8021ad Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: 8021q Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: macvlan Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: veth Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: bridge Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: Network device Fri Dec 2 13:26:41 2022 user.notice : Added device handler type: tunnel Fri Dec 2 13:26:41 2022 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network Fri Dec 2 13:26:41 2022 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.573422] mtk_soc_eth 1b100000.ethernet eth0: Link is Down Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.584579] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.593793] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.600751] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.615172] br-lan: port 1(lan1) entered blocking state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.620434] br-lan: port 1(lan1) entered disabled state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.627410] device lan1 entered promiscuous mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.632033] device eth0 entered promiscuous mode Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'lan' is enabled Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'lan' is setting up now Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'lan' is now up Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.642438] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.659222] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.669117] br-lan: port 2(lan2) entered blocking state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.674353] br-lan: port 2(lan2) entered disabled state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.681788] device lan2 entered promiscuous mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.691402] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.701190] br-lan: port 3(lan3) entered blocking state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.706450] br-lan: port 3(lan3) entered disabled state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.713818] device lan3 entered promiscuous mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.723221] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.733101] br-lan: port 4(lan4) entered blocking state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.738395] br-lan: port 4(lan4) entered disabled state Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.746704] device lan4 entered promiscuous mode Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'loopback' is enabled Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'loopback' is setting up now Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'loopback' is now up Fri Dec 2 13:26:42 2022 kern.info kernel: [ 9.759039] mt7530 mdio-bus:00 wan: configuring for phy/sgmii link mode Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'wan' is enabled Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'wan6' is enabled Fri Dec 2 13:26:42 2022 daemon.notice netifd: Network device 'eth0' link is up Fri Dec 2 13:26:42 2022 daemon.notice netifd: Network device 'lo' link is up Fri Dec 2 13:26:42 2022 daemon.notice netifd: Interface 'loopback' has link connectivity Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led Fri Dec 2 13:26:42 2022 user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system Fri Dec 2 13:26:42 2022 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system Fri Dec 2 13:26:42 2022 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN Fri Dec 2 13:26:42 2022 daemon.info procd: - init complete - Fri Dec 2 13:26:43 2022 daemon.err odhcpd[1576]: Failed to send to ff02::1%lan@br-lan (Address not available) Fri Dec 2 13:26:45 2022 kern.info kernel: [ 12.921270] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx Fri Dec 2 13:26:45 2022 kern.info kernel: [ 12.928860] br-lan: port 1(lan1) entered blocking state Fri Dec 2 13:26:45 2022 kern.info kernel: [ 12.934100] br-lan: port 1(lan1) entered forwarding state Fri Dec 2 13:26:45 2022 daemon.notice netifd: Network device 'lan1' link is up Fri Dec 2 13:26:45 2022 kern.info kernel: [ 12.941326] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready Fri Dec 2 13:26:45 2022 daemon.notice netifd: bridge 'br-lan' link is up Fri Dec 2 13:26:45 2022 daemon.notice netifd: Interface 'lan' has link connectivity Fri Dec 2 13:26:46 2022 daemon.err odhcpd[1576]: Failed to send to ff02::1%lan@br-lan (Address not available) Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: started, version 2.87 cachesize 150 Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: DNS service limited to local subnets Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus Fri Dec 2 13:26:46 2022 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for test Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for onion Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for localhost Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for local Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for invalid Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for bind Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: using only locally-known addresses for lan Fri Dec 2 13:26:46 2022 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /etc/hosts - 4 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /etc/hosts - 4 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c.2420 - 0 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 1 addresses Fri Dec 2 13:26:46 2022 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses Fri Dec 2 13:26:47 2022 daemon.info dnsmasq[1]: read /etc/hosts - 4 addresses Fri Dec 2 13:26:47 2022 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 2 addresses Fri Dec 2 13:26:47 2022 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 1 addresses Fri Dec 2 13:26:47 2022 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPDISCOVER(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPOFFER(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPDISCOVER(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPOFFER(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 Fri Dec 2 13:26:50 2022 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.1.230 84:2a:fd:20:bc:20 jason-laptop Fri Dec 2 13:27:58 2022 daemon.err uhttpd[1692]: [info] luci: failed login on / for root from 192.168.1.230 Fri Dec 2 13:28:05 2022 daemon.err uhttpd[1692]: [info] luci: accepted login on / for root from 192.168.1.230


Current version is 1.0.4, SPL source archive is here: https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar

Appears to be based on LEDE 17.01 and can be accessed from the device (https://192.168.1.x/cgi-bin/luci/) once the root password as be set via telnet/serial/ssh.

The command “mdio” is required: opkg install mdio-tools

To disable lan led's run: mdio mt7530-0 0:0x1f raw 0x21 0x0008

To make it permanent write it via the web UI at System→Startup→Local Startup, or via SSH into /etc/rc.local

To restore the blinking default behavior, run: mdio mt7530-0 0:0x1f raw 0x21 0x000b

Source: @dmatscheko on github: https://github.com/openwrt/openwrt/pull/11363#issuecomment-1379660930.

A few options exist for enabling telnet:

Being logged in on the normal web interface is required. To enable Debug mode, enter the Browser's Web Page Inspector, search HTML for telnet and unhide the entries by changing style=“display: none;” → style=“display”, hidden → visible. A checkbox “Enable Telnet” should appear in the webpage. Once clicked, the page reloads and the router can be accessed via telnet. the webUI admin account grants access to a root shell. Set a root password to access luci at https://router.ip/cgi-bin/luci/.

The debug_detail.htm also shows some stats like CPU/Memory/Flash Usage, one can enable Debug logging or lan/wan Packet Capturing (.pcap) to System Memory or USB drive. The file debuginfo.tar.gz can be downloaded directly.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1