User Tools

Site Tools


Linksys E3000 – Test Image Boot Log

This boot log is from r28295 with the George Kashperko patchset dated 2011-09-19. The Target Image was changed to an LZMA compressed ramdisk and booted via TFTP from the cfe for testing purposes.

CFE version 1.0.37 for BCM947XX (32bit,SP,LE) Build Date: Wed Jan 27 16:32:01 CST 2010 (ljh@team2-complier) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. No DPN This is a Parallel Flash Boot partition size = 262144(0x40000) et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller CPU type 0x19740: 480MHz Tot mem: 65536 KBytes CFE mem: 0x80700000 - 0x8079DAC0 (645824) Data: 0x80732A20 - 0x80737080 (18016) BSS: 0x80737080 - 0x80737AC0 (2624) Heap: 0x80737AC0 - 0x8079BAC0 (409600) Stack: 0x8079BAC0 - 0x8079DAC0 (8192) Text: 0x80700000 - 0x80732A1C (207388) Boot version: v4.2 The boot is CFE mac_init(): Find mac [68:7F:74:XX:XX:XX] in location 0 Nothing... No country code find Device eth0: hwaddr 68-7F-74-XX-XX-XX, ipaddr, mask gateway not set, nameserver not set Check CRC of image1 Header CRC: 0x2857AB9D Calculate CRC: 0x2857AB9D Image 1 is OK Try to load image 1. Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: Failed. Could not load :: Interrupted CFE> boot -tftp -elf Loader:elf Filesys:tftp Dev:eth0 File: Options:(null) Loading: 0x80001000/4304344 0x8041bdd8/127688 Entry at 0x80204690 Closing network. Starting program at 0x80204690 Linux version 3.0.4 ( (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Sat Sep 24 14:24:06 EDT 2011 CPU revision is: 00019740 (MIPS 74Kc) bcm47xx: using ssb bus ssb: Found END of erom after 9 cores ssb: chipcommon status is 0x800 ssb: ssb_pmu_resources_init: Resource count 7 ssb: Initializing MIPS core... ssb: set_irq: core 0x0812, irq 3 => 3 ssb: set_irq: core 0x082d, irq 4 => 4 ssb: set_irq: core 0x0819, irq 5 => 5 ssb: after irq reconfiguration ssb: core 0x0800, irq : 2(S)* 3 4 5 6 D I ssb: core 0x0812, irq : 2(S) 3* 4 5 6 D I ssb: core 0x082d, irq : 2(S) 3 4* 5 6 D I ssb: core 0x082c, irq : 2(S) 3 4 5 6 D I* ssb: core 0x0819, irq : 2(S) 3 4 5* 6 D I ssb: core 0x0820, irq : 2(S) 3 4 5 6* D I ssb: core 0x082e, irq : 2(S)* 3 4 5 6 D I ssb: core 0x080e, irq : 2(S) 3 4 5 6 D I* ssb: core 0x0834, irq : 2(S)* 3 4 5 6 D I found parallel flash. ssb: Sonics Silicon Backplane (AI type) found at address 0x18000000 Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 60576k/65536k available (2090k kernel code, 4960k reserved, 330k data, 1780k init, 0k highmem) NR_IRQS:128 console [ttyS0] enabled Calibrating delay loop... 239.10 BogoMIPS (lpj=478208) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 Switching to clocksource MIPS Switched to NOHz mode on CPU #0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. msgmni has been set to 118 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled serial8250: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A bcm47xx_pflash: flash init: 0x1c000000 0x02000000 Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000cb Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.1. number of CFI chips: 1 bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000 bcm47xx_part: bootloader size: 262144 bcm47xx_part: Looking for dual image bcm47xx_part: TRX offset : 0 4 bcm47xx partitions found on MTD device Physically mapped flash Creating 4 MTD partitions on "Physically mapped flash": 0x000000000000-0x000000040000 : "cfe" 0x000000040000-0x0000007f0000 : "linux" 0x0000000f4074-0x0000007f0000 : "rootfs" mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=305B0000, len=FFFFFFFFD0240000 0x0000305b0000-0x0000007f0000 : "rootfs_data" mtd: partition "rootfs_data" is out of reach -- disabled 0x0000007f0000-0x000000800000 : "nvram" bcm47xx_sflash: error registering platform driver: -19 BCM47xx Watchdog Timer enabled (30 seconds, nowayout) TCP westwood registered NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Freeing unused kernel memory: 1780k freed diag: Detected 'Linksys E3000 V1' roboswitch: Probing device eth0: No such device roboswitch: Probing device eth1: No such device roboswitch: Probing device eth2: No such device roboswitch: Probing device eth3: No such device - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - - init - Please press Enter to activate this console. bgmac ssb0:1: eth0: Broadcom SSB GMAC ethernet driver (ext. Robo Switch) 00:01:36:XX:XX:XX SCSI subsystem initialized roboswitch: Probing device eth0: found a 53115! It's a 5350. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb wl: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint wl0: Broadcom BCM4329 802.11 Wireless Controller SSB/BCMA glue driver successfully attached PPP generic driver version 2.4.2 ip_tables: (C) 2000-2006 Netfilter Core Team device eth0.0 entered promiscuous mode device eth0 entered promiscuous mode NET: Registered protocol family 24 br-lan: port 1(eth0.0) entering forwarding state br-lan: port 1(eth0.0) entering forwarding state ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver USB20H mdio control register: 0x8000000C ehci_hcd ssb0:2: SSB EHCI Controller ehci_hcd ssb0:2: new USB bus registered, assigned bus number 1 ehci_hcd ssb0:2: irq 5, io mem 0x18004000 ehci_hcd ssb0:2: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected nf_conntrack version 0.5.0 (974 buckets, 3896 max) uhci_hcd: USB Universal Host Controller Interface driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. BusyBox v1.18.5 (2011-09-24 13:42:47 EDT) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ATTITUDE ADJUSTMENT (bleeding edge, r28295) ---------- * 1/4 oz Vodka Pour all ingredients into mixing * 1/4 oz Gin tin with ice, strain into glass. * 1/4 oz Amaretto * 1/4 oz Triple sec * 1/4 oz Peach schnapps * 1/4 oz Sour mix * 1 splash Cranberry juice ----------------------------------------------------- root@OpenWrt:/#

toh/linksys/e3000/3.0.4_bootlog.txt · Last modified: 2018/02/20 18:51 by