D-Link DWR-960

CDG56CDL_0T3 Jboot B972 JRecovery Version R1.2 2016/11/15 14:11 spi device id: ef 40 18 0 0 (40180000) SPI FLASH: W25Q128FV 16M . .................... Starting kernel @80000000... LINUX started... THIS IS ASIC Linux version 2.6.36 (tja@localhost.localdomain) (gcc version 4.3.5 (Buildroot 2011.05) ) #45 Wed Apr 26 18:58:59 CST 2017 CMD_LINE:console=ttyS1,57600n8 root=/dev/mtdblock3 The CPU feqenuce set to 580 MHz PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=000563f0 Readback ErrCtl register=000563f0 Memory: 60928k/65536k available (3016k kernel code, 4608k reserved, 733k data, 172k init, 0k highmem) Hierarchical RCU implementation. RCU debugfs-based tracing is enabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:128 Console: colour dummy device 80x25 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 48b09d RALINK_GPIOMODE = 48b09d PPLL_CFG1=0xe70000 MT7620 PPLL lock PPLL_DRV =0x80080504 start PCIe register access RALINK_PCI_PCICFG_ADDR = 1000f0 *************** MT7620 PCIe RC mode ************* bio: create slab <bio-0> at 0 vgaarb: loaded usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x20100000-0x2010ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20100000-0x2010ffff] (PCI address [0x20100000-0x2010ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] pci 0000:00:00.0: bridge window [mem pref disabled] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20100000 res[1]->end = 2010ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RT3xxx EHCI/OHCI init. squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 119 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) HDLC line discipline maxframe=4096 N_HDLC line discipline registered. Ralink gpio driver initialized Enable Ralink GDMA Controller Module GDMA IP Version=3 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : ef 40 18 0 0 (40180000) W25Q128BV(ef 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 4096 Creating 6 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "Whole" 0x000000000000-0x000000010000 : "Bootloader" 0x000000010000-0x000000150000 : "Kernel" 0x000000180000-0x000000f10000 : "RootFS" 0x000000f10000-0x000000ff0000 : "UI" 0x000000ff0000-0x000001000000 : "Config" rdm_major = 253 SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x432880f8 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! NAPI enable, Tx Ring = 256, Rx Ring = 256 SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x432880f1 PROC INIT OK! PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected u32 classifier Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (952 buckets, 3808 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 IPv4 over IPv4 tunneling driver GRE over IPv4 demultiplexor driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 172k freed Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed switch register base addr to system register 0xb0000000 multicast|bytes write offset 0x34, value 0x1800000 packets errs write offset 0x34, value 0x0 drop fifo colls carriRaeth v3.0 (erNAPI c,SkbRecycleo) mpres phy_tx_ring = 0x03fb0000, tx_ring = 0xa3fb0000 phy_rx_ring0 = 0x03fb1000, rx_ring0 = 0xa3fb1000 0x7,Read PhyID is 0x4d ,0xd072!! AR Phy SMACCR1 -- : 0x0000000c SMACCR0 -- : 0x432880f1 seCDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 tunl0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 gre0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 flash_open: flash_fd=3 Mount D Section. addrconf_dad_completed 7 flash_open: flash_fd=9 switch register base addr to system register 0xb0000000 write offset 0x60, value 0x48b01d Tue Jan 1 00:00:00 UTC 2013 timezone:0 dsttime:0 switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10001 switch reg write offset=2514, value=10002 sh: ebtables: not found sh: ebtables: not found sh: ebtables: not found sh: ebtables: not found vconfig: ioctl error for add: File exists Set port eth2.1.0 vconfig: ioctl error for add: File exists device eth2 entered promiscuous mode set hello timer failed: Invalid argument device eth2.1 entered promiscuous mode sh: ebtables: not found br0: port 1(eth2.1) entering forwarding state br0: port 1(eth2.1) entering forwarding state Set port eth2.2.0 vconfig: ioctl error for add: File exists , Enable: 1 Wireless 5G AP0, Enable: 1 phy 0, reg 0, val 0x800 Set: phy[0].reg[0] = 0800 phy 1, reg 0, val 0x800 Set: phy[1].reg[0] = 0800 phy 2, reg 0, val 0x800 Set: phy[2].reg[0] = 0800 phy 3, reg 0, val 0x800 Set: phy[3].reg[0] = 0800 phy 4, reg 0, val 0x800 Set: phy[4].reg[0] = 0800 phy 5, reg 0, val 0x800 Set: phy[5].reg[0] = 0800 sh: ebtables: not found sh: ebtables: not found sh: ebtables: not found sh: ebtables: not found sh: ebtables: not found flramtd_erase: addr:ff0000 len:0 ash_open: flash_fd=9 ramtd_write: to:ff0000 len:10 ramtd_write: to:ff0010 len:f7e ramtd_write: to:ff0000 len:1 phy 0, reg 0, val 0x3300 Set: phy[0].reg[0] = 3300 phy 1, reg 0, val 0x3300 Set: phy[1].reg[0] = 3300 addrconf_dad_completed 7 phy 2, reg 0, val 0x3300 Set: phy[2].reg[0] = 3300 addrconf_dad_completed 7 phy 3, reg 0, val 0x3300 Set: phy[3].reg[0] = 3300 addrconf_dad_completed 7 phy 4, reg 0, val 0x3300 Set: phy[4].reg[0] = 3300 phy 5, reg 0, val 0x3300 Set: phy[5].reg[0] = 3300 init sys init vlan init lan init stp init ondemand init multiwan2 init multi_ondemand init load_balance init routing init nat nat initial init dhcpsrv ESW: Link Status Changed - Port0 Link UP ==== NAT START (WAN:ALL Func:ALL) ==== addrconf_dad_completed 7 cat: /var/nat/nat.wan: No such file or directory ESW: Link Status Changed - Port3 Link UP sdmz_enable:0 server_config.pool_check = 1 server_config.pool_check = 1 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0 0 Unable to open /var/run/udhcpd.leases for reading udhcpd (v0.9.9-pre) started Unable to open /var/run/udhcpd.leases for reading init dnsrelay init spap init ddns init snmp init route_protocol rm: cannot remove '/etc/ripd.conf': No such file or directory cat: /var/run/ripd.pid: No such file or directory BusyBox v1.3.2 (2017-01-04 19:52:56 CST) multi-call binary Usage: kill [-l] [-signal] process-id [process-id ...] cat: /var/run/zebra.pid: No such file or directory BusyBox v1.3.2 (2017-01-04 19:52:56 CST) multi-call binary Usage: kill [-l] [-signal] process-id [process-id ...] init half_bridge init time timezone:-60 dsttime:0 init rbydom init rbyip init qos init keepalive init user init ftp_alg init rtsp_alg init schedule init mupnpd init watchdog init reboot init wireless_mode sdmz_enable:0 server_config.pool_check = 1 server_config.pool_check = 1 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0 start = 192.168.0.50, end = 192.168.0.199, lan_ip = 192.168.0.1, interface=br0, ifindex=0 0 udhcpd (v0.9.9-pre) started init wlanap init wps_status init wps_btn init wpa init pwd init ipv6 init v6filter modprobe: module ip6_tables not found modprobe: failed to load module ip6_tables modprobe: module ip6table_filter not found modprobe: failed to load module ip6table_filter modprobe: module ip6table_mangle not found modprobe: failed to load module ip6table_mangle modprobe: module ip6t_rt not found modprobe: failed to load module ip6t_rt modprobe: module ip6t_REJECT not found modprobe: failed to load module ip6t_REJECT init ddnsv6 init tr069 init russian_p1wan init hwnat init 3g_status init 3g_setting init wan_alias init sip_alg init ssh killall: dropbear: no process killed init igmp init reset_btn init ate killall: ated: no process killed init wan_led init recent init dynamic_lanip init iom /usr/bin/ataskset: /usr/bin/ataskset: 6: taskset: not found flash_open: flash_fd=4 /var/nat/nat-draft.uyg: /var/nat/nat-draft.uyg: 141: cannot create /proc/sys/net/ipv4/route/secret_interval: Directory nonexistent SINGLE DMZ start flash_open: flash_fd=4 gre_post Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`). modprobe: module ip6_tables not found modprobe: failed to load module ip6_tables ip6tables v1.4.10: can't initialize ip6tables table `filter': iptables who? (do you need to insmod?) Perhaps ip6tables or your kernel needs to be upgraded. # Ralink APSoC Hardware Watchdog Timer Started WatchDog Timer. Started WatchDog Timer. LoadVlaue: 36600 sysclk: 145000000 TIMEOUT: 60 rt2860v2_ap: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint Length of MAC:6 mac:74:da:da:34:1:20: ---- === pAd = c072d000, size = 1042232 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.1.6 Length of MAC:6 mac:74:da:da:34:1:21: ---- === pAd = c0d02000, size = 1274328 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 device_id =0x7610 ==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002 MACVersion = 0x76502000 NVM is EFUSE RX DESC a3148000 size = 2048 RTMP_TimerListAdd: add timer obj c07aa0c8! RTMP_TimerListAdd: add timer obj c073524c! RTMP_TimerListAdd: add timer obj c0734e40! RTMP_TimerListAdd: add timer obj c073521c! RTMP_TimerListAdd: add timer obj c0735558! RTMP_TimerListAdd: add timer obj c0735498! RTMP_TimerListAdd: add timer obj c07354c8! RTMP_TimerListAdd: add timer obj c0738688! RTMP_TimerListAdd: add timer obj c073827c! RTMP_TimerListAdd: add timer obj c0738658! RTMP_TimerListAdd: add timer obj c0738994! RTMP_TimerListAdd: add timer obj c07388d4! RTMP_TimerListAdd: add timer obj c0738904! RTMP_TimerListAdd: add timer obj c073bac4! RTMP_TimerListAdd: add timer obj c073b6b8! RTMP_TimerListAdd: add timer obj c073ba94! RTMP_TimerListAdd: add timer obj c073bdd0! RTMP_TimerListAdd: add timer obj c073bd10! RTMP_TimerListAdd: add timer obj c073bd40! RTMP_TimerListAdd: add timer obj c073ef00! RTMP_TimerListAdd: add timer obj c073eaf4! RTMP_TimerListAdd: add timer obj c073eed0! RTMP_TimerListAdd: add timer obj c073f20c! RTMP_TimerListAdd: add timer obj c073f14c! RTMP_TimerListAdd: add timer obj c073f17c! RTMP_TimerListAdd: add timer obj c074233c! RTMP_TimerListAdd: add timer obj c0741f30! RTMP_TimerListAdd: add timer obj c074230c! RTMP_TimerListAdd: add timer obj c0742648! RTMP_TimerListAdd: add timer obj c0742588! RTMP_TimerListAdd: add timer obj c07425b8! RTMP_TimerListAdd: add timer obj c0745778! RTMP_TimerListAdd: add timer obj c074536c! RTMP_TimerListAdd: add timer obj c0745748! RTMP_TimerListAdd: add timer obj c0745a84! RTMP_TimerListAdd: add timer obj c07459c4! RTMP_TimerListAdd: add timer obj c07459f4! RTMP_TimerListAdd: add timer obj c0748bb4! RTMP_TimerListAdd: add timer obj c07487a8! RTMP_TimerListAdd: add timer obj c0748b84! RTMP_TimerListAdd: add timer obj c0748ec0! RTMP_TimerListAdd: add timer obj c0748e00! RTMP_TimerListAdd: add timer obj c0748e30! RTMP_TimerListAdd: add timer obj c074bff0! RTMP_TimerListAdd: add timer obj c074bbe4! RTMP_TimerListAdd: add timer obj c074bfc0! RTMP_TimerListAdd: add timer obj c074c2fc! RTMP_TimerListAdd: add timer obj c074c23c! RTMP_TimerListAdd: add timer obj c074c26c! RTMP_TimerListAdd: add timer obj c074f42c! RTMP_TimerListAdd: add timer obj c074f020! RTMP_TimerListAdd: add timer obj c074f3fc! RTMP_TimerListAdd: add timer obj c074f738! RTMP_TimerListAdd: add timer obj c074f678! RTMP_TimerListAdd: add timer obj c074f6a8! RTMP_TimerListAdd: add timer obj c0752868! RTMP_TimerListAdd: add timer obj c075245c! RTMP_TimerListAdd: add timer obj c0752838! RTMP_TimerListAdd: add timer obj c0752b74! RTMP_TimerListAdd: add timer obj c0752ab4! RTMP_TimerListAdd: add timer obj c0752ae4! RTMP_TimerListAdd: add timer obj c0755ca4! RTMP_TimerListAdd: add timer obj c0755898! RTMP_TimerListAdd: add timer obj c0755c74! RTMP_TimerListAdd: add timer obj c0755fb0! RTMP_TimerListAdd: add timer obj c0755ef0! RTMP_TimerListAdd: add timer obj c0755f20! RTMP_TimerListAdd: add timer obj c07590e0! RTMP_TimerListAdd: add timer obj c0758cd4! RTMP_TimerListAdd: add timer obj c07590b0! RTMP_TimerListAdd: add timer obj c07593ec! RTMP_TimerListAdd: add timer obj c075932c! RTMP_TimerListAdd: add timer obj c075935c! RTMP_TimerListAdd: add timer obj c075c51c! RTMP_TimerListAdd: add timer obj c075c110! RTMP_TimerListAdd: add timer obj c075c4ec! RTMP_TimerListAdd: add timer obj c075c828! RTMP_TimerListAdd: add timer obj c075c768! RTMP_TimerListAdd: add timer obj c075c798! RTMP_TimerListAdd: add timer obj c075f958! RTMP_TimerListAdd: add timer obj c075f54c! RTMP_TimerListAdd: add timer obj c075f928! RTMP_TimerListAdd: add timer obj c075fc64! RTMP_TimerListAdd: add timer obj c075fba4! RTMP_TimerListAdd: add timer obj c075fbd4! RTMP_TimerListAdd: add timer obj c0762d94! RTMP_TimerListAdd: add timer obj c0762988! RTMP_TimerListAdd: add timer obj c0762d64! RTMP_TimerListAdd: add timer obj c07630a0! RTMP_TimerListAdd: add timer obj c0762fe0! RTMP_TimerListAdd: add timer obj c0763010! RTMP_TimerListAdd: add timer obj c07661d0! RTMP_TimerListAdd: add timer obj c0765dc4! RTMP_TimerListAdd: add timer obj c07661a0! RTMP_TimerListAdd: add timer obj c07664dc! RTMP_TimerListAdd: add timer obj c076641c! RTMP_TimerListAdd: add timer obj c076644c! RTMP_TimerListAdd: add timer obj c0780a34! RTMP_TimerListAdd: add timer obj c0780b50! RTMP_TimerListAdd: add timer obj c0780a60! RTMP_TimerListAdd: add timer obj c076683c! RTMP_TimerListAdd: add timer obj c07324dc! RTMP_TimerListAdd: add timer obj c0735918! RTMP_TimerListAdd: add timer obj c0738d54! RTMP_TimerListAdd: add timer obj c073c190! RTMP_TimerListAdd: add timer obj c073f5cc! RTMP_TimerListAdd: add timer obj c0742a08! RTMP_TimerListAdd: add timer obj c0745e44! RTMP_TimerListAdd: add timer obj c0749280! RTMP_TimerListAdd: add timer obj c074c6bc! RTMP_TimerListAdd: add timer obj c074faf8! RTMP_TimerListAdd: add timer obj c0752f34! RTMP_TimerListAdd: add timer obj c0756370! RTMP_TimerListAdd: add timer obj c07597ac! RTMP_TimerListAdd: add timer obj c075cbe8! RTMP_TimerListAdd: add timer obj c0760024! RTMP_TimerListAdd: add timer obj c0763460! RTMP_TimerListAdd: add timer obj c0766550! RTMP_TimerListAdd: add timer obj c07668a4! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 DyncVga disable 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = 1, D2 = 9, CalCode = 19 !!! RT6352_Temperature_Init : BBPR49 = 0x1 RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7 Current Temperature from BBP_R49=0xfffffffb TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= f, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 3, phase=39) TX IQ Calibration Done! RXIQ Sigma_i=731, Sigma_q=742, R_iq=850 RXIQ calibration FAIL RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l RTMP_TimerListAdd: add timer obj c0766b68! Main bssid = 74:da:da:34:01:20 <==== rt28xx_init, Status=0 0x1300 = 00064380 device ra0 entered promiscuous mode br0: port 2(ra0) entering forwarding state br0: port 2(ra0) entering forwarding state addrconf_dad_completed 7 RTMP_TimerListAdd: add timer obj c06f9418! load fw spent 16ms RX DESC a322e000 size = 2048 RX1 DESC a322f000 size = 2048 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! 1. Phy Mode = 49 2. Phy Mode = 49 ext_pa_current_setting = 1 3. Phy Mode = 49 AntCfgInit: primary/secondary ant 0/1 ChipStructAssign(): RALINK6590 hook ! MCS Set = ff 00 00 00 01 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) Main bssid = 74:da:da:34:01:21 <==== rt28xx_init, Status=0 usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=3, PrimCh=48, HT-CentCh=46, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=48, HT-CentCh=46, VHT-CentCh=42, BBP_BW=2) 0x1300 = 00064380 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! device rai0 entered promiscuous mode br0: port 3(rai0) entering forwarding state br0: port 3(rai0) entering forwarding state addrconf_dad_completed 7 Queue of usbnet RX [1514][60] TX[1514][60] qmi_wwan 1-1:1.4: usbnet0: register 'qmi_wwan' at usb-rt3xxx-1, WWAN/QMI device, 9e:f2:de:f4:2d:16 usbcore: registered new interface driver qmi_wwan usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) option 1-1:1.0: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 option 1-1:1.2: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 option 1-1:1.3: GSM modem (1-port) converter detected usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems Algorithmics/MIPS FPU Emulator v1.5 ramtd_erase: addr:ff0000 len:0 ramtd_write: to:ff0000 len:10 ramtd_write: to:ff0010 len:f80 ramtd_write: to:ff0000 len:1 Queue of usbnet RX [1514][60] TX[1514][60] addrconf_dad_completed 7 Ralink HW NAT Module Enabled

CDG56CDL_0T3 Jboot B972 JRecovery Version R1.2 2016/11/15 14:11 spi device id: ef 40 18 0 0 (40180000) SPI FLASH: W25Q128FV 16M . ....................... Starting kernel @80000000... [ 0.000000] Linux version 4.14.172 (X@Y) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r8378+4301-9ac7350240)) #0 Fri Apr 10 07:06:02 2020 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is D-Link DWR-960 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a0 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=000563f6 [ 0.000000] Readback ErrCtl register=000563f6 [ 0.000000] Memory: 58360K/65536K available (3921K kernel code, 191K rwdata, 896K rodata, 1192K init, 212K bss, 7176K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015469] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.087722] pid_max: default: 32768 minimum: 301 [ 0.097147] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.110170] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.130402] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.149883] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.162107] pinctrl core: initialized pinctrl subsystem [ 0.172915] NET: Registered protocol family 16 [ 0.443285] PCI host bridge /pcie@10140000 ranges: [ 0.452685] MEM 0x0000000020000000..0x000000002fffffff [ 0.463060] IO 0x0000000010160000..0x000000001016ffff [ 0.492268] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.503302] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.515872] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.526869] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.539445] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.550443] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.562995] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.573814] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.586671] PCI host bridge to bus 0000:00 [ 0.594665] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.608379] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.620110] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.633610] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.649791] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.666261] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.679314] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.693125] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 0.706624] pci 0000:00:00.0: BAR 1: assigned [mem 0x20100000-0x2010ffff] [ 0.720135] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 0.733630] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.743479] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 0.762529] clocksource: Switched to clocksource systick [ 0.774234] NET: Registered protocol family 2 [ 0.783632] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.797413] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.810000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.822788] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.834310] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.847063] NET: Registered protocol family 1 [ 0.858577] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.871362] Crashlog allocated RAM at address 0x3f00000 [ 0.883598] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.902957] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.914456] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.946354] io scheduler noop registered [ 0.954064] io scheduler deadline registered (default) [ 0.965035] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.978689] console [ttyS0] disabled [ 0.985752] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 1.005419] console [ttyS0] enabled [ 1.005419] console [ttyS0] enabled [ 1.019230] bootconsole [early0] disabled [ 1.019230] bootconsole [early0] disabled [ 1.040896] spi spi0.0: force spi mode3 [ 1.060049] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 1.069485] 3 fixed-partitions partitions found on MTD device spi0.0 [ 1.082147] Creating 3 MTD partitions on "spi0.0": [ 1.091703] 0x000000000000-0x000000010000 : "jboot" [ 1.102363] 0x000000010000-0x000000ff0000 : "firmware" [ 1.115135] 2 jimage-fw partitions found on MTD device firmware [ 1.127000] Creating 2 MTD partitions on "firmware": [ 1.136906] 0x000000000000-0x000000198d6a : "kernel" [ 1.147698] 0x000000198d6a-0x000000fe0000 : "rootfs" [ 1.158411] mtd: device 3 (rootfs) set to be root filesystem [ 1.171355] 1 squashfs-split partitions found on MTD device rootfs [ 1.183750] 0x0000003cd000-0x000000fe0000 : "rootfs_data" [ 1.195436] 0x000000ff0000-0x000001000000 : "config" [ 1.206975] libphy: Fixed MDIO Bus: probed [ 1.225085] gsw: setting port4 to ephy mode [ 1.233497] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex) [ 1.251690] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex) [ 1.269933] mtk_soc_eth 10100000.ethernet: generated random MAC address c2:76:41:f0:27:96 [ 1.286407] libphy: mdio: probed [ 1.327523] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:07 [uid=004dd072, driver=Atheros 8035 ethernet] [ 1.350358] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 1.362814] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.379825] rt2880_wdt 10000120.watchdog: Initialized [ 1.391204] NET: Registered protocol family 10 [ 1.404135] Segment Routing with IPv6 [ 1.411612] NET: Registered protocol family 17 [ 1.420556] 8021q: 802.1Q VLAN Support v1.8 [ 1.436257] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.456860] Freeing unused kernel memory: 1192K [ 1.465918] This architecture does not have kernel memory protection. [ 2.344168] init: Console is alive [ 2.351299] init: - watchdog - [ 2.627223] random: fast init done [ 3.586320] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.739814] usbcore: registered new interface driver usbfs [ 3.750899] usbcore: registered new interface driver hub [ 3.761632] usbcore: registered new device driver usb [ 3.778714] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.793555] ehci-platform: EHCI generic platform driver [ 3.814359] phy phy-usbphy.0: remote usb device wakeup disabled [ 3.826166] phy phy-usbphy.0: UTMI 16bit 30MHz [ 3.835037] ehci-platform 101c0000.ehci: EHCI Host Controller [ 3.846521] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 3.862421] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 3.882600] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 3.896106] hub 1-0:1.0: USB hub found [ 3.904073] hub 1-0:1.0: 1 port detected [ 3.915258] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.929350] ohci-platform: OHCI generic platform driver [ 3.940135] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 3.953734] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 3.969614] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.007603] hub 2-0:1.0: USB hub found [ 4.015628] hub 2-0:1.0: 1 port detected [ 4.029776] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.048387] init: - preinit - [ 5.060062] random: jshn: uninitialized urandom read (4 bytes read) [ 5.143183] random: jshn: uninitialized urandom read (4 bytes read) [ 5.431051] random: jshn: uninitialized urandom read (4 bytes read) [ 6.115313] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.127022] 8021q: adding VLAN 0 to HW filter on device eth0 [ 6.138395] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 6.150884] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 6.193018] urandom_read: 4 callbacks suppressed [ 6.193027] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.553200] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.348812] jffs2: notice: (459) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found. [ 8.381954] mount_root: switching to jffs2 overlay [ 8.425584] overlayfs: upper fs does not support tmpfile. [ 8.441582] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.581086] procd: - early - [ 8.587056] procd: - watchdog - [ 9.117322] procd: - watchdog - [ 9.123951] procd: - ubus - [ 9.238371] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.351130] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.365354] procd: - init - Please press Enter to activate this console. [ 10.218421] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.259207] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.296779] usbcore: registered new interface driver cdc_wdm [ 10.327337] Loading modules backported from Linux version v5.4.27-0-g585e0cc08069 [ 10.342325] Backport generated by backports.git v5.4.27-1-0-gf6e8852f [ 10.388957] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.425142] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 10.587016] xt_time: kernel timezone is -0000 [ 10.704885] urngd: jent-rng init failed, err: 2 [ 10.734135] PPP generic driver version 2.4.2 [ 10.749371] NET: Registered protocol family 24 [ 10.761319] usbcore: registered new interface driver qmi_wwan [ 10.788334] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 10.800952] mt76x0e 0000:01:00.0: ASIC revision: 76100002 [ 10.814461] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 [ 10.910093] mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00 [ 10.965714] ieee80211 phy1: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'. [ 11.010070] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 11.025582] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected [ 11.118035] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.741773] 8021q: adding VLAN 0 to HW filter on device eth0 [ 20.766029] device eth0 entered promiscuous mode [ 20.785519] br-lan: port 1(eth0.1) entered blocking state [ 20.796355] br-lan: port 1(eth0.1) entered disabled state [ 20.807489] device eth0.1 entered promiscuous mode [ 20.881134] br-lan: port 1(eth0.1) entered blocking state [ 20.891959] br-lan: port 1(eth0.1) entered forwarding state [ 20.903271] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 21.769864] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.023316] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 26.127487] qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device [ 26.146638] qmi_wwan 1-1:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, be:d5:eb:dd:fa:2b