D-Link DIR-865L A1

D-Link DIR-865L

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

Supported Versions

Experimental Versions

None at this time.

Hardware Highlights

Installation

CFE Web Recovery

Basically, this device has a built-in web interface that allows you to upload a firmware to recover the system over HTTP.

  1. Set your PC's IP address to 192.168.0.2 and subnet mask to 255.255.255.0
  2. Press and hold the reset button (behind) until the orange power indicator blinks constantly.
  3. Navigate to http://192.168.0.1 and you should see a page which asks you to upload a file.
  4. Upload an OpenWrt TRX file or stock firmware and wait for a success message
  5. If web browser is constantly loading, restart from step 2.

Snapshots

Step 3

Step 4

Flash Layout

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

OEM easy installation

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

OEM installation using the TFTP method

→ generic.flashing.tftp

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

Upgrading OpenWrt

→ generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Debricking

→ generic.debrick

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

Switch Ports (for VLANs)

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

Buttons

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The D-Link DIR-865L has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

Hardware

Info

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for D-Link DIR-865L A1 		EXAMPLE 115200, 8N1, 3.3V

JTAG

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

→ bootloader

Hardware mods

None so far.

Bootlogs

OEM bootlog

SVN revision: 668 Decompressing...done CFE version 6.30.39.2001 (r334376) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE) Build Date: Mon Jul 16 13:56:31 CST 2012 (michael_lee@Porsche) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. Boot partition size = 327680(0x50000) Found an ST compatible serial flash with 256 64KB blocks; total size 16MB bcm_robo_enable_switch: EEE is disabled et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.2001 (r334376) CPU type 0x19749: 600MHz Tot mem: 131072 KBytes CFE mem: 0x80700000 - 0x807A57C0 (677824) Data: 0x8073AA10 - 0x8073DDC0 (13232) BSS: 0x8073DDC0 - 0x8073F7C0 (6656) Heap: 0x8073F7C0 - 0x807A37C0 (409600) Stack: 0x807A37C0 - 0x807A57C0 (8192) Text: 0x80700000 - 0x8073AA08 (240136) Board Name: WRGAC01 SVN revision: 668 We disable the arp for self. We disable the arp for self. Device eth0: hwaddr 00-90-4C-0D-B0-18, ipaddr 192.168.0.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: Failed. Could not load :: Timeout occured Dest=80001000, source =807a57c0, filename=flash1.trx verify_seama: data=0x8073a4a0, size=-2139465792 SEAMA ========================================== magic : 5ea3a417 meta size : 36 bytes meta data : dev=/dev/mtdblock/1 meta data : type=firmware meta data : meta data : image size : 10367008 bytes verify_seama: signature=[(null)], type=[firmware] checksum : E2FD8DE98AF176C1808572DD778C5CBE digest : E2FD8DE98AF176C1808572DD778C5CBE Selected !!! ================================================ seama check OK!! insize = 2097152, out size =8388608 uncompressed size = 4604038 lzma decompress success ! Closing network. Starting program at 0x80001000 Linux version 2.6.22 (lilian@cdWSCMPL01) (gcc version 4.2.3) #1 Thu Jan 4 17:56:36 CST 2018 CPU revision is: 00019749 Found an ST compatible serial flash with 256 64KB blocks; total size 16MB Determined physical RAM map: memory: 07fff000 @ 00000000 (usable) memory: 08000000 @ 87fff000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0 -> 131072 HighMem 131072 -> 589823 early_node_map[2] active PFN ranges 0: 0 -> 32767 0: 557055 -> 589823 Built 1 zonelists. Total pages: 65535 Kernel command line: root=/dev/mtdblock0 console=ttyS0,115200 noinitrd Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) CPU: BCM5300 rev 1 at 600 MHz Using 300.000 MHz high precision timer. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 253680k/131068k available (3542k kernel code, 8164k reserved, 729k data, 224k init, 131072k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Initializing host PCI: Reset RC PCI: Initializing host PCI: Reset RC PCI: Fixing up bus 0 PCI/PCIe coreunit 0 is set to bus 1. PCI: Fixing up bridge PCI: Fixing up bridge PCI: Enabling device 0000:01:00.1 (0004 -> 0006) PCI: Fixing up bus 1 PCI/PCIe coreunit 1 is set to bus 2. PCI: Fixing up bridge PCI: Fixing up bridge PCI: Enabling device 0000:02:00.1 (0004 -> 0006) PCI: Fixing up bus 2 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher fuse init (API version 7.8), DCACHE_BUG enabled io scheduler noop registered (default) HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.7 pflash: found no supported devices sflash: the flash image has SEAMA header, retry: 0 sflash: squashfs filesystem found at offset 1769536 Creating 9 MTD partitions on "sflash": 0x001b0060-0x00a33060 : "rootfs" 0x00050000-0x00f50000 : "upgrade" 0x00040000-0x00050000 : "devconf" 0x00030000-0x00040000 : "devdata" 0x00fd0000-0x00ff0000 : "langpack" 0x00000000-0x01000000 : "flash" 0x00000000-0x00030000 : "u-boot" 0x00ff0000-0x01000000 : "nvram" 0x00f50000-0x00fd0000 : "mydlink" No NAND flash type found nflash: found no supported devices No NAND flash type found brcmnand: found no supported devices usbmon: debugfs is not available ehci_hcd 0000:00:04.1: EHCI Host Controller ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting ehci_hcd 0000:00:04.1: irq 6, io mem 0x18004000 ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd 0000:00:04.0: OHCI Host Controller ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:04.0: irq 6, io mem 0x18009000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected u32 classifier nf_conntrack version 0.5.0 (2047 buckets, 16376 max) xt_time: kernel timezone is -0000 BCM fast NAT: INIT ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 224k freed Failed to execute /init init started: BusyBox v1.14.1 (2018-01-03 10:22:55 CST) starting pid 668, tty '': '/etc/init.d/rcS' Algorithmics/MIPS FPU Emulator v1.5 [/etc/init.d/S10init.sh] [/etc/init.d/S11upboot.sh] [/etc/init.d/S12ubs_storage.sh] [/etc/init.d/S15udevd.sh] [/etc/init.d/S16ipv6.sh] [/etc/init.d/S19init.sh] [/etc/init.d/S20init.sh] DEFNODE[/etc/defnodes/S11devdata.xml] DEFNODE[/etc/defnodes/S12flashspeed.php] DEFNODE[/etc/defnodes/S13dfs.php] DEFNODE[/etc/defnodes/S14setchlist.php] DEFNODE[/etc/defnodes/S20device.xml] DEFNODE[/etc/defnodes/S22timezone.php] [/etc/scripts/setdate.sh] 01/01/2000 ... Sat Jan 1 08:00:04 GMT 2000 DEFNODE[/etc/defnodes/S30device.php] DEFNODE[/etc/defnodes/S30device.xml] DEFNODE[/etc/defnodes/S31diagnostic.xml] DEFNODE[/etc/defnodes/S31locale.php] DEFNODE[/etc/defnodes/S33wifi.php] DEFNODE[/etc/defnodes/S40device.xml] DEFNODE[/etc/defnodes/S40links.php] DEFNODE[/etc/defnodes/S90opendns.php] DEFNODE[/etc/defnodes/S90sessions.php] DEFNODE[/etc/defnodes/S90sessions_privatekey.php] DEFNODE[/etc/defnodes/S90upnpigd.php] DEFNODE[/etc/defnodes/S90upnpwfa.php] DEFNODE[/etc/defnodes/S91upnpigd2.php] DEVCONF: unable to read config data (ret=-3) ! Fri Jan 5 00:00:00 GMT 2018 Generating a 2048 bit RSA private key ..................+++ ....................................+++ writing new private key to '/tmp/server.key' ----- SERVD: start service [LOGD] [/etc/init.d/S20interfaces.sh] /proc/sys/net/ipv6/conf/eth2/accept_dad: can't create /proc/sys/net/ipv6/conf/eth2/disable_ipv6: can't create SIOCGIFINDEX: No such device SIOCGIFFLAGS: No such device [/etc/init.d/S21usbmount.sh] [/etc/init.d/S22mydlink.sh] [/etc/init.d/S22mydlink.sh] Generate mydlink uid XqdoHwvmPcCi0v58 [/etc/init.d/S23udevd.sh] [/etc/init.d/S45gpiod.sh] Factory reset time : 5 secs 00: WPS Button using GPIO #14, input mode. 01: Factory Reset Button using GPIO #5, input mode. 02: Power_Status LED Green using GPIO #0, output mode. 03: Power_Status LED Orange using GPIO #1, output mode. 04: Internet LED Orange using GPIO #3, output mode. 05: Internet LED Green using GPIO #2, output mode. 06: USB using GPIO #7, output mode. et interface not found [/etc/init.d/rcS] done! SERVD: event [WANPORT.LINKDOWN] not found! [/etc/init0.d/S21layout.sh]: start ... SERVD: start service [LAYOUT] [/etc/init0.d/S40event.sh]: start ... SERVD: event [SEALPAC.LOAD/default] SEAMA: '/dev/mtdblock/4' is not a seama file ! [/etc/init0.d/S40gpioevent.sh]: start ... en[/etc/init0.d/S41autowan.sh]: start ... [/etc/init0.d/S41autowanv6.sh]: start ... [/etc/init0.d/S41event.sh]: start ... [/etc/init0.d/S41inf.sh]: start ... SERVD: start service [LOGD] SERVD: service [LOGD] is already started. SERVD: start service [BRIDGE] [/etc/init0.d/S41smart404.sh]: start ... BRIDGE: The device is not in the bridge mode. SERVD: start service [LAN] SERVD: start service [PHYINF.ETH-1] [/etc/init0.d/S42event.sh]: start ... [/etc/init0.d/S42pthrough.sh]: start ... SERVD: start service [WAN] [/etc/init0.d/S43mydlinkevent.sh]: start ... [/etc/init0.d/S51wlan.sh]: start ... SERVD: start service [PHYINF.ETH-2] PHYINF.ETH-2: cfg[00:de:fa:1a:02:00] curr[00:00:00:00:00:00], restart the device !!! SERVD: start service [PHYINF.ETH-3] SERVD: start service [IPTABLES] CONNTRACK_MAX=36000 CONNTRACK_MIN=36000 [/etc/init0.d/S60shareport.sh]: start ... [/etc/init0.d/S65ddnsd.sh]: start ... [/etc/init0.d/S65user.sh]: start ... [/etc/init0.d/S80telnetd.sh]: start ... killall: telnetd: no process killed Create /var/proc/alpha symbolic link... SERVD: start service [IP6TABLES] SERVD: start service [IPTABLES] SERVD: service [IPTABLES] is already started. SERVD: start service [IP6TABLES] SERVD: service [IP6TABLES] is already started. SERVD: start service [INET.LAN-1] [/var/servd/INET.LAN-1_start.sh]: starting LAN-1... SERVD: event [LAN-1.UP/default] /proc/nf_accelerate_to_local: can't create [/var/servd/INET.LAN-1_start.sh]: starting LAN-1 done !!! SERVD: start service [INET.LAN-2] [/var/servd/INET.LAN-2_start.sh]: starting LAN-2... SERVD: event [LAN-2.UP/default] [/var/servd/INET.LAN-2_start.sh]: starting LAN-2 done !!! SERVD: start service [INET.LAN-4] #!/bin/sh # No inet profile!! exit 9 SERVD: start service [INET.LAN-5] #!/bin/sh # No inet profile!! exit 9 SERVD: start service [INET.LAN-6] ifsetup: (LAN-6) not active. SERVD: service [INET.LAN-6] return error 8. SERVD: start service [IPTMACCTRL] SERVD: start service [IPTURLCTRL] SERVD: start service [ACCESSCTRL] SERVD: start service [IPTPORTT] SERVD: start service [IPT.LAN-1] /proc/fastnat/forskipsupport: can't create SERVD: start service [IP6T.LAN-1] SERVD: start service [IPT.LAN-2] /proc/fastnat/forskipsupport: can't create SERVD: start service [IP6T.LAN-2] SERVD: start service [IPT.LAN-3] SERVD: service [IPT.LAN-3] return error 108. SERVD: start service [IP6T.LAN-3] SERVD: start service [IPT.LAN-4] SERVD: service [IPT.LAN-4] return error 108. SERVD: start service [IP6T.LAN-4] SERVD: start service [IPT.LAN-5] SERVD: service [IPT.LAN-5] return error 108. SERVD: start service [IP6T.LAN-5] SERVD: start service [IPT.LAN-6] SERVD: service [IPT.LAN-6] return error 108. SERVD: start service [IP6T.LAN-6] SERVD: start service [DEVICE.PASSTHROUGH] SERVD: start service [IPTABLES] SERVD: service [IPTABLES] is already started. SERVD: start service [IP6TABLES] SERVD: service [IP6TABLES] is already started. SERVD: start service [INET.WAN-1] [/var/servd/INET.WAN-1_start.sh]: starting WAN-1... [/var/servd/INET.WAN-1_start.sh]: starting WAN-1 done !!! SERVD: start service [MYDLINK.LOG] SERVD: start service [INET.WAN-2] ifsetup: (WAN-2) not active. SERVD: service [INET.WAN-2] return error 8. SERVD: start service [INET.WAN-3] [/var/servd/INET.WAN-3_start.sh]: starting WAN-3... WAN-3 a is link local interface. SERVD: event [WAN-3.UP/default] [/var/servd/INET.WAN-3_start.sh]: starting WAN-3 done !!! SERVD: start service [INET.WAN-4] ifsetup: (WAN-4) not active. SERVD: service [INET.WAN-4] return error 8. SERVD: start service [WIFI.PHYINF] SERVD: service [WIFI.PHYINF] return error 108. SERVD: start service [INET.WAN-5] ifsetup: (WAN-5) not active. SERVD: service [INET.WAN-5] return error 8. SERVD: start service [IPTMASQ] /proc/sys/net/ipv4/ip_personality_sport: can't create /proc/sys/net/ipv4/ip_personality_enable: can't create SERVD: start service [IPTVSVR] SERVD: start service [IPTPFWD] SERVD: start service [IPTPORTT] SERVD: service [IPTPORTT] is already started. SERVD: start service [IPTDMZ] SERVD: start service [IPT.WAN-1] SERVD: start service [IP6T.WAN-1] SERVD: start service [IPT.WAN-2] SERVD: start service [IP6T.WAN-2] SERVD: start service [IPT.WAN-3] SERVD: start service [IP6T.WAN-3] SERVD: start service [IPT.WAN-4] SERVD: start service [IP6T.WAN-4] SERVD: start service [IPT.WAN-5] SERVD: service [IPT.WAN-5] return error 108. SERVD: start service [IP6T.WAN-5] SERVD: service [IP6T.WAN-5] return error 108. SERVD: start service [PHYINF.WIFI] SERVD: start service [DEVICE.ACCOUNT] Password for 'Admin' has been updated SERVD: start service [SHAREPORT] SERVD: stop service [INFSVCS.LAN-1] SERVD: service [INFSVCS.LAN-1] is already stopped. SERVD: start service [INFSVCS.LAN-1] SERVD: event [LAN-1.CONNECTED] not found! SERVD: event [INFSVCS.LAN-1.UP/default] SERVD: event [STATUS.READY/default] SERVD: stop service [INFSVCS.LAN-2] SERVD: service [INFSVCS.LAN-2] is already stopped. SERVD: start service [INFSVCS.LAN-2] SERVD: event [LAN-2.CONNECTED] not found! SERVD: event [INFSVCS.LAN-2.UP] not found! SERVD: stop service [IPT.LAN-1] /proc/fastnat/forskipsupport: can't create SERVD: start service [IPT.LAN-1] /proc/fastnat/forskipsupport: can't create SERVD: stop service [IPT.LAN-2] /proc/fastnat/forskipsupport: can't create SERVD: start service [IPT.LAN-2] /proc/fastnat/forskipsupport: can't create SERVD: stop service [IPT.LAN-3] SERVD: service [IPT.LAN-3] is already stopped. SERVD: start service [IPT.LAN-3] SERVD: service [IPT.LAN-3] return error 108. SERVD: stop service [IPT.LAN-4] SERVD: service [IPT.LAN-4] is already stopped. SERVD: start service [IPT.LAN-4] SERVD: service [IPT.LAN-4] return error 108. SERVD: stop service [IPT.LAN-5] SERVD: service [IPT.LAN-5] is already stopped. SERVD: start service [IPT.LAN-5] SERVD: service [IPT.LAN-5] return error 108. SERVD: stop service [IPT.LAN-6] SERVD: service [IPT.LAN-6] is already stopped. SERVD: start service [IPT.LAN-6] SERVD: service [IPT.LAN-6] return error 108. SERVD: stop service [INFSVCS.WAN-3] SERVD: service [INFSVCS.WAN-3] is already stopped. SERVD: start service [INFSVCS.WAN-3] SERVD: event [WAN-3.CONNECTED] not found! SERVD: event [UPDATERESOLV/default] SERVD: event [INFSVCS.WAN-3.UP] not found! SERVD: event [UPNP.IGD.NOTIFY.WANIPCONN1] not found! SERVD: start service [PHYINF.BAND24G-1.1] acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x180a [ephp.c read_cond_list 1197] PHP operator precedence issue at: /etc/scripts/wifirnodes.php, cond_qty: 3, and_qty: 11 updatewifistats -s /etc/scripts/upwifistatshlper_G_band.sh -m bcm -i wifig0 -x /phyinf:4 -r /runtime/phyinf:4 & SERVD: event [BAND24G-1.LED.ON] not found! SERVD: start service [PHYINF.BAND24G-1.2] SERVD: service [PHYINF.BAND24G-1.2] return error 8. SERVD: start service [PHYINF.BAND5G-1.1] acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0xe22a [ephp.c read_cond_list 1197] PHP operator precedence issue at: /etc/scripts/wifirnodes.php, cond_qty: 3, and_qty: 11 updatewifistats -s /etc/scripts/upwifistatshlper_A_band.sh -m bcm -i wifia0 -x /phyinf:6 -r /runtime/phyinf:5 & SERVD: event [BAND5G-1.LED.ON] not found! aaaaaaaa SERVD: start service [PHYINF.BAND5G-1.2] SERVD: service [PHYINF.BAND5G-1.2] return error 8. SERVD: stop service [WEBACCESS] SERVD: service [WEBACCESS] is already stopped. SERVD: start service [WEBACCESS] webaccesssetup: (WAN-1) no phyinf. killall: fileaccessd: no process killed SERVD: start service [ENLAN] Reading topology file /var/topology.conf ... l2_packet_receive - recvfrom: Network is down broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=0 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=1 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=2 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=3 Using interface wifig0 with hwaddr 9c:d6:43:be:d3:30 and ssid 'dlink-D330' ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== broadcom_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 l2_packet_receive - recvfrom: Network is down broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=0 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=1 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=2 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=3 Using interface wifia0 with hwaddr 9c:d6:43:be:d3:32 and ssid 'dlink-media-D332' ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== broadcom_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 aaaaaaaa Signal 15 received - terminating broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 Removing station 9c:d6:43:be:d3:30 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 Removing station 9c:d6:43:be:d3:32 SERVD: event [IPV6ENABLE/default] SERVD: event [IPV6ENABLE/default] SERVD: event [IPV6ENABLE/default] SERVD: start service [HTTP.LAN-1] SERVD: start service [UPNP.LAN-1] SERVD: event [UPNP.ALIVE.LAN-1/default] SERVD: start service [NEAP.LAN-1] SERVD: service [NEAP.LAN-1] return error 108. SERVD: start service [NAMERESOLV.LAN-1] SERVD: start service [DHCPS4.LAN-1] Reading topology file /var/topology.conf ... SERVD: start service [DNS4.LAN-1] SERVD: stop service [BWC.LAN-1] SERVD: service [BWC.LAN-1] is already stopped. SERVD: start service [BWC.LAN-1] l2_packet_receive - recvfrom: Network is down broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=0 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=1 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=2 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=3 Using interface wifig0 with hwaddr 9c:d6:43:be:d3:30 and ssid 'dlink-D330' LAN-1 Start Traffic Control system ... LAN-1 Traffic Control is disabled. SERVD: start service [INET.LAN-3] [/var/servd/INET.LAN-3_start.sh]: starting LAN-3... ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== broadcom_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 LAN-3 a is link local interface. SERVD: event [LAN-3.UP/default] [/var/servd/INET.LAN-3_start.sh]: starting LAN-3 done !!! SERVD: start service [ENLAN] SERVD: service [ENLAN] is already started. SERVD: start service [HTTP.LAN-2] l2_packet_receive - recvfrom: Network is down broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=0 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=1 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=2 broadcom_set_key: alg=none addr=00:00:00:00:00:00 key_idx=3 Using interface wifia0 with hwaddr 9c:d6:43:be:d3:32 and ssid 'dlink-media-D332' httpsetup: (LAN-2) not active. SERVD: service [HTTP.LAN-2] return error 8. SERVD: start service [DHCPS4.LAN-2] SERVD: start service [DNS4.LAN-2] SERVD: stop service [ROUTE.STATIC] SERVD: service [ROUTE.STATIC] is already stopped. SERVD: start service [ROUTE.STATIC] SERVD: stop service [ROUTE.IPUNNUMBERED] SERVD: service [ROUTE.IPUNNUMBERED] is already stopped. SERVD: start service [ROUTE.IPUNNUMBERED] SERVD: stop service [IPTOBF] SERVD: service [IPTOBF] is already stopped. SERVD: start service [IPTOBF] ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== ====================================================== If the sta can't connect to ap/router using wpa/wpa2, please check the wpa and rsn capabitity is match the one in driver or not ====================================================== broadcom_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:30 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 wpa_auth_sta_init: IE = 30 18 01 00 00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 02 0c 00 dd 1c 00 50 f broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 broadcom_set_key: alg=none addr=9c:d6:43:be:d3:32 key_idx=0 SERVD: stop service [IPTDEFCHAIN] SERVD: service [IPTDEFCHAIN] is already stopped. SERVD: start service [IPTDEFCHAIN] killall: proxyd: no process killed Read configuration file /var/run/proxyd.conf... Read url configuration file /var/run/proxyd_url.conf... Start http proxy server... Start server at br0 port 5449 insmod: can't insert '/lib/modules/nf_conntrack_ipsec_pass.ko': unknown symbol in module, or unknown parameter insmod: can't insert '/lib/modules/nf_nat_proto_gre.ko': unknown symbol in module, or unknown parameter insmod: can't insert '/lib/modules/nf_conntrack_proto_gre.ko': unknown symbol in module, or unknown parameter SERVD: stop service [LLD2] SERVD: service [LLD2] is already stopped. SERVD: start service [LLD2] SERVD: start service [HTTP.WAN-3] httpsetup: (WAN-3) not active. SERVD: service [HTTP.WAN-3] return error 8. SERVD: stop service [IP6TDEFCHAIN] SERVD: service [IP6TDEFCHAIN] is already stopped. SERVD: start service [IP6TDEFCHAIN] SERVD: stop service [ROUTE6.DYNAMIC] SERVD: service [ROUTE6.DYNAMIC] is already stopped. SERVD: start service [ROUTE6.DYNAMIC] SERVD: stop service [ROUTE6.STATIC] SERVD: service [ROUTE6.STATIC] is already stopped. SERVD: start service [ROUTE6.STATIC] SERVD: stop service [DEVICE.TIME] SERVD: service [DEVICE.TIME] is already stopped. SERVD: start service [DEVICE.TIME] Run NTP client ... SERVD: stop service [ROUTE.DYNAMIC] SERVD: service [ROUTE.DYNAMIC] is already stopped. SERVD: start service [ROUTE.DYNAMIC] [V4] [] SERVD: service [ROUTE.DYNAMIC] return error 108. SERVD: stop service [EMAIL] SERVD: service [EMAIL] is already stopped. SERVD: start service [EMAIL] ntpclient -h ntp1.dlink.com -i 5 -s ntp1.dlink.com: Unknown host SERVD: stop service [UPNPC] SERVD: service [UPNPC] is already stopped. SERVD: start service [UPNPC] SERVD: service [UPNPC] return error 108. SERVD: stop service [MULTICAST] SERVD: service [MULTICAST] is already stopped. SERVD: start service [MULTICAST] NTP4 will run in 10 seconds! [mldproxy_main.c 106] mldproxy start... SERVD: stop service [STUNNEL] SERVD: service [STUNNEL] is already stopped. SERVD: start service [STUNNEL] Start Stunnel service .. SERVD: stop service [IPT.WAN-1] SERVD: start service [IPT.WAN-1] SERVD: stop service [MDNSRESPONDER] SERVD: service [MDNSRESPONDER] is already stopped. SERVD: start service [MDNSRESPONDER] mdnsresponder server start ! SERVD: stop service [NAMERESOLV] SERVD: service [NAMERESOLV] is already stopped. SERVD: start service [NAMERESOLV] SERVD: stop service [INFSVCS.LAN-3] SERVD: service [INFSVCS.LAN-3] is already stopped. SERVD: start service [INFSVCS.LAN-3] SERVD: event [LAN-3.CONNECTED] not found! SERVD: event [INFSVCS.LAN-3.UP] not found! SERVD: stop service [DNS] SERVD: service [DNS] is already stopped. SERVD: start service [DNS] killall: dnsmasq: no process killed SERVD: stop service [IPT.WAN-3] SERVD: start service [IPT.WAN-3] SERVD: start service [LOG.EMAIL] SERVD: stop service [HTTP] SERVD: service [HTTP] is already stopped. SERVD: start service [HTTP] SERVD: event [HTTP.UP] not found! SERVD: start service [ENLAN] SERVD: service [ENLAN] is already started. SERVD: start service [HTTP.LAN-3] SERVD: start service [UPNP.LAN-3] SERVD: event [UPNP.ALIVE.LAN-3/default] SERVD: start service [NAMERESOLV.LAN-3] SERVD: stop service [ROUTE6.STATIC] SERVD: start service [ROUTE6.STATIC] SERVD: stop service [ROUTE6.DYNAMIC] SERVD: start service [ROUTE6.DYNAMIC] SERVD: stop service [IP6TOBF] SERVD: service [IP6TOBF] is already stopped. SERVD: start service [IP6TOBF] SERVD: stop service [IP6TDEFCHAIN] SERVD: start service [IP6TDEFCHAIN] SERVD: stop service [ROUTE.DYNAMIC] SERVD: service [ROUTE.DYNAMIC] is already stopped. SERVD: start service [ROUTE.DYNAMIC] SERVD: service [ROUTE.DYNAMIC] return error 108. SERVD: stop service [LLD2] SERVD: start service [LLD2] SERVD: stop service [HTTP] SERVD: event [HTTP.DOWN] not found! SERVD: start service [HTTP] startup_server:IPV6, is multicast SERVD: event [HTTP.UP] not found! SERVD: stop service [NAMERESOLV] SERVD: start service [NAMERESOLV] Run NTP client ... [V6] [] ************************ * Please login * ************************ Login:


OpenWrt bootlog

SVN revision: 668 Decompressing...done CFE version 6.30.39.2001 (r334376) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE) Build Date: Mon Jul 16 13:56:31 CST 2012 (michael_lee@Porsche) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. Boot partition size = 327680(0x50000) Found an ST compatible serial flash with 256 64KB blocks; total size 16MB bcm_robo_enable_switch: EEE is disabled et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.2001 (r334376) CPU type 0x19749: 600MHz Tot mem: 131072 KBytes CFE mem: 0x80700000 - 0x807A57C0 (677824) Data: 0x8073AA10 - 0x8073DDC0 (13232) BSS: 0x8073DDC0 - 0x8073F7C0 (6656) Heap: 0x8073F7C0 - 0x807A37C0 (409600) Stack: 0x807A37C0 - 0x807A57C0 (8192) Text: 0x80700000 - 0x8073AA08 (240136) Board Name: WRGAC01 SVN revision: 668 We disable the arp for self. We disable the arp for self. Device eth0: hwaddr 00-90-4C-0D-B0-18, ipaddr 192.168.0.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: Failed. Could not load :: Timeout occured Dest=80001000, source =807a57c0, filename=flash1.trx verify_seama: data=0x8073a4a0, size=-2139465792 digest check fail Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: .. 3768 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 [ 0.000000] Linux version 5.10.168 (lee@ArchBoxE14G3) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r20068-3 [ 0.000000] CPU0 revision is: 00019749 (MIPS 74Kc) [ 0.000000] bcm47xx: Using bcma bus [ 0.000000] (NULL device *): bus0: Found chip with id 0x5300, rev 0x01 and package 0x00 [ 0.000000] Found 128 MiB of extra memory, but highmem is unsupported yet! [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] This processor doesn't support highmem. -131068k highmem ignored [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffefff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32479 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=800000e0 [ 0.000000] Readback ErrCtl register=800000e0 [ 0.000000] Cache parity protection enabled [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 122548K/131068K available (5081K kernel code, 603K rwdata, 1024K rodata, 192K init, 293K bss) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] bcm47xx_soc: bus0: Core 0 found: BCM4706 ChipCommon (manuf 0x4BF, id 0x500, rev 0x1F, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 1 found: BCM4706 GBit MAC (manuf 0x4BF, id 0x52D, rev 0x00, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 2 found: BCM4706 GBit MAC (manuf 0x4BF, id 0x52D, rev 0x00, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x00, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x04, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 6 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 7 found: AMEMC (DDR) (manuf 0x4BF, id 0x52E, rev 0x00, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 8 found: BCM4706 SOC RAM (manuf 0x4BF, id 0x50E, rev 0x05, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 9 found: ALTA (I2S) (manuf 0x4BF, id 0x534, rev 0x00, class 0x0) [ 0.000000] bcm47xx_soc: bus0: Core 10 found: BCM4706 GBit MAC Common (manuf 0x43B, id 0x5DC, rev 0x00, class 0) [ 0.000000] bcm47xx_soc: bus0: Found M25FL128 serial flash (size: 16384KiB, blocksize: 0x10000, blocks: 256) [ 0.000000] bcm47xx_soc: bus0: Early bus registered [ 0.000000] MIPS: machine is Unknown Board [ 0.000000] bcm47xx: Setting up vectored interrupts [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns [ 0.000012] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns [ 0.000140] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136) [ 0.070065] pid_max: default: 32768 minimum: 301 [ 0.070297] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.070329] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.073119] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.074269] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.074314] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.075654] NET: Registered protocol family 16 [ 0.130009] clocksource: Switched to clocksource MIPS [ 0.131643] NET: Registered protocol family 2 [ 0.131976] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.132789] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.132899] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.132937] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.132968] TCP: Hash tables configured (established 1024 bind 1024) [ 0.133137] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.133187] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.133574] NET: Registered protocol family 1 [ 0.133646] PCI: CLS 0 bytes, default 32 [ 0.203027] can not parse nvram name (null)pa0maxpwr(null) with value 400 got -34 [ 0.293737] ------------[ cut here ]------------ [ 0.293783] WARNING: CPU: 0 PID: 1 at drivers/bcma/host_soc.c:140 bcma_host_soc_aread32+0x6c/0x74 [ 0.293796] Accessed core has no wrapper/agent [ 0.293807] Modules linked in: [ 0.293839] CPU: 0 PID: 1 Comm: swapper Not tainted 5.10.168 #0 [ 0.293853] Stack : 80680000 805a0928 00000000 00000000 80c2dc84 806c0000 80600000 80579b58 [ 0.293917] 80c28328 80601de7 806c36ac 00000001 00000007 00000001 80c2dc38 93168bd4 [ 0.293978] 00000000 00000000 80579b58 80c2dad8 ffffefff 00000000 00000000 ffffffea [ 0.294038] 00000000 80c2dae4 00000062 80607e88 00000000 00000009 80c2dd18 8035099c [ 0.294099] 00000009 00000007 80c2ddd0 805b12dc 00000018 00000030 00000000 806c0000 [ 0.294160] ... [ 0.294181] Call Trace: [ 0.294220] [<800072b0>] show_stack+0x30/0x100 [ 0.294248] [<800244bc>] __warn+0xb0/0x11c [ 0.294270] [<800245b4>] warn_slowpath_fmt+0x8c/0xac [ 0.294293] [<8035099c>] bcma_host_soc_aread32+0x6c/0x74 [ 0.294315] [<8034eabc>] bcma_core_mips_irqflag+0x48/0xa0 [ 0.294337] [<8034eb88>] bcma_core_mips_irq+0x28/0xc4 [ 0.294359] [<8034f320>] bcma_core_mips_init+0x340/0x51c [ 0.294405] [<80348640>] bcma_bus_register+0x25c/0x6bc [ 0.294439] [<80692f50>] bcm47xx_register_bus_complete+0x40/0xcc [ 0.294461] [<80001238>] do_one_initcall+0x50/0x1a8 [ 0.294483] [<80690f78>] kernel_init_freeable+0x1e0/0x278 [ 0.294524] [<804f1540>] kernel_init+0x10/0xf8 [ 0.294546] [<80002738>] ret_from_kernel_thread+0x14/0x1c [ 0.294566] [ 0.294622] ---[ end trace 3fd49230dc93d3e3 ]--- [ 0.294671] bcm47xx_soc: bus0: PCIEcore in host mode found [ 0.495233] PCI host bridge to bus 0000:00 [ 0.495274] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff] [ 0.495297] pci_bus 0000:00: root bus resource [io 0x0100-0x047f] [ 0.495320] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.495340] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.495412] bcma: PCI: Fixing up bridge 0000:00:00.0 [ 0.495430] bcma: PCI: Fixing up device 0000:00:00.0 [ 0.495465] pci 0000:00:00.0: [14e4:5300] type 00 class 0x060000 [ 0.495507] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.495538] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x07ffffff 64bit] [ 0.495574] pci 0000:00:00.0: enabling Extended Tags [ 0.495665] pci 0000:00:00.0: supports D1 D2 [ 0.495951] bcma: PCI: Fixing up bridge 0000:00:00.1 [ 0.495980] bcma: PCI: Fixing up device 0000:00:00.1 [ 0.496016] pci 0000:00:00.1: [14e4:0000] type 00 class 0x060000 [ 0.496058] pci 0000:00:00.1: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.496091] pci 0000:00:00.1: reg 0x18: [mem 0x00000000-0x07ffffff 64bit] [ 0.496126] pci 0000:00:00.1: enabling Extended Tags [ 0.496212] pci 0000:00:00.1: supports D1 D2 [ 0.496555] pci 0000:00:01.0: [14e4:4360] type 00 class 0x028000 [ 0.496629] pci 0000:00:01.0: reg 0x10: [mem 0x08000000-0x08007fff 64bit] [ 0.496721] bcma: PCI: Fixing up addresses 0000:00:01.0 [ 0.496755] pci 0000:00:01.0: BAR 0: assigned [mem 0x08000000-0x08007fff 64bit] [ 0.496933] pci 0000:00:01.0: supports D1 D2 [ 0.496955] pci 0000:00:01.0: PME# supported from D3cold [ 0.497032] pci 0000:00:01.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:0) [ 0.497320] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.497396] bcm47xx_soc: bus0: PCIEcore in host mode found [ 0.707546] PCI host bridge to bus 0000:01 [ 0.707590] pci_bus 0000:01: root bus resource [mem 0x40000000-0x43ffffff] [ 0.707613] pci_bus 0000:01: root bus resource [io 0x0480-0x07ff] [ 0.707636] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0] [ 0.707656] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.707724] bcma: PCI: Fixing up bridge 0000:01:00.0 [ 0.707742] bcma: PCI: Fixing up device 0000:01:00.0 [ 0.707778] pci 0000:01:00.0: [14e4:5300] type 00 class 0x060000 [ 0.707819] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.707851] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x07ffffff 64bit] [ 0.707886] pci 0000:01:00.0: enabling Extended Tags [ 0.707976] pci 0000:01:00.0: supports D1 D2 [ 0.708259] bcma: PCI: Fixing up bridge 0000:01:00.1 [ 0.708288] bcma: PCI: Fixing up device 0000:01:00.1 [ 0.708323] pci 0000:01:00.1: [14e4:0000] type 00 class 0x060000 [ 0.708366] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.708397] pci 0000:01:00.1: reg 0x18: [mem 0x00000000-0x07ffffff 64bit] [ 0.708433] pci 0000:01:00.1: enabling Extended Tags [ 0.708520] pci 0000:01:00.1: supports D1 D2 [ 0.710213] pci 0000:01:01.0: [14e4:4331] type 00 class 0x028000 [ 0.710901] pci 0000:01:01.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 0.712165] pci 0000:01:01.0: enabling Extended Tags [ 0.712336] bcma: PCI: Fixing up addresses 0000:01:01.0 [ 0.712380] pci 0000:01:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff 64bit] [ 0.714964] pci 0000:01:01.0: supports D1 D2 [ 0.716208] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.717165] bcm47xx_soc: bus0: Bus registered [ 0.726459] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.732478] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.732509] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.734445] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 0.735098] printk: console [ttyS0] disabled [ 0.755330] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1562500) is a U6_16550A [ 1.752825] printk: console [ttyS0] enabled [ 1.777677] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2, base_baud = 1562500) is a U6_16550A [ 1.936507] 3 bcm47xxpart partitions found on MTD device bcm47xxsflash [ 1.943305] Creating 3 MTD partitions on "bcm47xxsflash": [ 1.948897] 0x000000000000-0x000000050000 : "boot" [ 1.960797] 0x000000050000-0x000000ff0000 : "firmware" [ 1.967025] failed to parse "brcm,trx-magic" DT attribute, using default: -89 [ 1.974531] 3 trx partitions found on MTD device firmware [ 1.980151] Creating 3 MTD partitions on "firmware": [ 1.985293] 0x00000000001c-0x00000000091c : "loader" [ 1.990459] mtd: partition "loader" doesn't start on an erase/write block boundary -- force read-only [ 2.003018] 0x00000000091c-0x000000200800 : "linux" [ 2.008072] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only [ 2.019785] 0x000000200800-0x000000fa0000 : "rootfs" [ 2.025007] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 2.036260] mtd: setting mtd4 (rootfs) as root device [ 2.041600] 1 squashfs-split partitions found on MTD device rootfs [ 2.047996] 0x000000670000-0x000000fa0000 : "rootfs_data" [ 2.055899] 0x000000ff0000-0x000001000000 : "nvram" [ 2.077679] bgmac_bcma bcma0:1: Found PHY addr: 30 (NOREGS) [ 2.163846] b53_common: found switch: BCM53125, rev 4 [ 2.169205] bgmac_bcma bcma0:1: Support for Roboswitch not implemented [ 2.177847] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.184066] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds) [ 2.192178] bcma-pci-bridge 0000:00:01.0: enabling device (0000 -> 0002) [ 2.199118] bcma: PCI: Fixing up device 0000:00:01.0 [ 2.204316] bcma: change PCIe max read request size from 512 to 128 [ 2.210886] bcma-pci-bridge 0000:00:01.0: bus1: Found chip with id 0x4360, rev 0x02 and package 0x01 [ 2.220414] bcma-pci-bridge 0000:00:01.0: bus1: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class) [ 2.231445] bcma-pci-bridge 0000:00:01.0: bus1: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x28, clas) [ 2.242591] bcma-pci-bridge 0000:00:01.0: bus1: Core 2 found: ARM CR4 (manuf 0x4BF, id 0x83E, rev 0x00, class 0x) [ 2.253384] bcma-pci-bridge 0000:00:01.0: bus1: Core 3 found: PCIe Gen2 (manuf 0x4BF, id 0x83C, rev 0x00, class ) [ 2.264327] bcma-pci-bridge 0000:00:01.0: bus1: Core 4 found: USB 2.0 Device (manuf 0x4BF, id 0x81A, rev 0x0E, c) [ 2.310214] bcma-pci-bridge 0000:00:01.0: bus1: Bus registered [ 2.317490] bcma-pci-bridge 0000:01:01.0: enabling device (0000 -> 0002) [ 2.326670] bcma: PCI: Fixing up device 0000:01:01.0 [ 2.331999] bcma: change PCIe max read request size from 512 to 128 [ 2.338941] bcma-pci-bridge 0000:01:01.0: bus2: Found chip with id 0x4331, rev 0x02 and package 0x08 [ 2.348622] bcma-pci-bridge 0000:01:01.0: bus2: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class) [ 2.359689] bcma-pci-bridge 0000:01:01.0: bus2: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1D, clas) [ 2.370852] bcma-pci-bridge 0000:01:01.0: bus2: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x13, class 0x0) [ 2.505448] bcma-pci-bridge 0000:01:01.0: bus2: Invalid SPROM read from the PCIe card, trying to use fallback SPM [ 2.680375] bcma-pci-bridge 0000:01:01.0: bus2: Bus registered [ 2.687558] NET: Registered protocol family 10 [ 2.696610] Segment Routing with IPv6 [ 2.700640] NET: Registered protocol family 17 [ 2.705342] 8021q: 802.1Q VLAN Support v1.8 [ 2.717030] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.724979] Freeing unused kernel memory: 192K [ 2.729581] This architecture does not have kernel memory protection. [ 2.736313] Run /sbin/init as init process [ 3.583231] init: Console is alive [ 3.587278] init: - watchdog - [ 5.446460] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.585277] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.603340] init: - preinit - [ 7.952003] random: jshn: uninitialized urandom read (4 bytes read) [ 8.148039] random: jshn: uninitialized urandom read (4 bytes read) [ 8.278184] random: jshn: uninitialized urandom read (4 bytes read) [ 8.522701] bgmac_bcma bcma0:1 eth0: Link is Up - 1Gbps/Full - flow control off [ 8.537764] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.552502] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 13.141444] jffs2: notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (1. [ 13.159645] mount_root: switching to jffs2 overlay [ 13.172635] overlayfs: upper fs does not support tmpfile. [ 13.190800] urandom-seed: Seeding with /etc/urandom.seed [ 13.362210] procd: - early - [ 13.365545] procd: - watchdog - [ 14.111341] procd: - watchdog - [ 14.117008] procd: - ubus - [ 14.266862] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.276786] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.284104] random: ubusd: uninitialized urandom read (4 bytes read) [ 14.303320] procd: - init - Please press Enter to activate this console. [ 15.791848] random: jshn: uninitialized urandom read (4 bytes read) [ 15.827640] random: ubusd: uninitialized urandom read (4 bytes read) [ 15.840332] random: ubus: uninitialized urandom read (4 bytes read) [ 16.313204] urngd: v1.0.2 started. [ 16.648576] random: crng init done [ 16.652191] random: 20 urandom warning(s) missed due to ratelimiting [ 16.752942] kmodloader: loading kernel modules from /etc/modules.d/* [ 17.058939] Loading modules backported from Linux version v5.15.92-0-ge515b9902f5f [ 17.066830] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c [ 17.360518] PPP generic driver version 2.4.2 [ 17.369422] NET: Registered protocol family 24 [ 17.755522] wl: module license 'unspecified' taints kernel. [ 17.761342] Disabling lock debugging due to kernel taint [ 17.823403] Unsupported BCMA bus type 0 [ 17.827403] wl_glue: probe of bcma1:1 failed with error -22 [ 17.833250] Unsupported BCMA bus type 0 [ 17.837235] wl_glue: probe of bcma2:1 failed with error -22 [ 17.843176] SSB/BCMA glue driver successfully attached [ 17.867692] b43-phy0: Broadcom 4360 WLAN found (core revision 40) [ 17.874603] b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 0) [ 17.882976] b43: probe of bcma1:1 failed with error -122 [ 17.888578] b43-phy1: Broadcom 4331 WLAN found (core revision 29) [ 17.895496] b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1 [ 17.901944] b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1 [ 17.910481] Broadcom 43xx driver loaded [ Features: NL ] [ 18.120816] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.598118] bgmac_bcma bcma0:1 eth0: Link is Up - 1Gbps/Full - flow control off [ 39.624380] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 39.633802] br-lan: port 1(eth0.1) entered blocking state [ 39.639401] br-lan: port 1(eth0.1) entered disabled state [ 39.645475] device eth0.1 entered promiscuous mode [ 39.650503] device eth0 entered promiscuous mode [ 39.687975] br-lan: port 1(eth0.1) entered blocking state [ 39.693633] br-lan: port 1(eth0.1) entered forwarding state [ 40.650110] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 46.810097] b43-phy1: Loading firmware version 784.2 (2012-08-15 21:35:19) [ 47.216672] br-lan: port 2(wlan1) entered blocking state [ 47.222238] br-lan: port 2(wlan1) entered disabled state [ 47.228187] device wlan1 entered promiscuous mode [ 48.733871] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 48.740811] br-lan: port 2(wlan1) entered blocking state [ 48.746319] br-lan: port 2(wlan1) entered forwarding state [ 49.816350] ------------[ cut here ]------------ [ 49.821247] WARNING: CPU: 0 PID: 1075 at backports-5.15.92-1/drivers/net/wireless/broadcom/b43/main.c:4225 b43_h] [ 49.834043] Modules linked in: pppoe ppp_async nft_fib_inet nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_c [ 49.899695] CPU: 0 PID: 1075 Comm: hostapd Tainted: P W 5.10.168 #0 [ 49.907561] Stack : 80680000 805a0928 00000000 00000000 81f958cc 806c0000 80600000 80579b58 [ 49.916284] 80d03b88 80601de7 806c36ac 00000433 827e0200 00000001 81f95880 4594772b [ 49.924990] 00000000 00000000 80579b58 81f95720 ffffefff 00000000 00000000 ffffffea [ 49.933699] 00000000 81f9572c 00000149 80607e88 80000000 00000009 00000000 8198359c [ 49.942418] 00000009 827e0200 00000000 00000000 00000018 802f5ef0 00000000 806c0000 [ 49.951136] ... [ 49.953679] Call Trace: [ 49.956234] [<800072b0>] show_stack+0x30/0x100 [ 49.960883] [<800244bc>] __warn+0xb0/0x11c [ 49.965132] [<80024584>] warn_slowpath_fmt+0x5c/0xac [ 49.970335] [<8198359c>] b43_hf_write+0x4e8/0x6ac [b43] [ 49.975741] [ 49.977283] ---[ end trace 3fd49230dc93d3e5 ]--- [ 49.982100] wlan1: failed to set key (4, ff:ff:ff:ff:ff:ff) to hardware (-22) BusyBox v1.35.0 (2023-03-09 23:13:29 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 22.03-SNAPSHOT, r20068-788a0cf15c ----------------------------------------------------- root@OpenWrt:/#


Notes

Space for additional notes, links to forum threads or other resources.

  • ...

Tags

FIXME Add tags below, then remove this fixme.

How to add tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1