Cubieboard2

U-Boot SPL 2013.10-rc2 (Feb 27 2014 - 22:16:14) Board: Cubieboard2 DRAM: 1024 MiB CPU: 960000000Hz, AXI/AHB/APB: 3/2/2 spl: not an uImage at 1600 U-Boot 2013.10-rc2 (Feb 27 2014 - 22:16:14) Allwinner Technology CPU: Allwinner A20 (SUN7I) Board: Cubieboard2 I2C: ready DRAM: 1 GiB MMC: SUNXI SD/MMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: emac Hit any key to stop autoboot: 3  2  1  0 reading uEnv.txt 240 bytes read in 2 ms (117.2 KiB/s) Loaded environment from uEnv.txt Running uenvcmd ... reading uImage 2371480 bytes read in 191 ms (11.8 MiB/s) reading dtb 16105 bytes read in 3 ms (5.1 MiB/s) ## Booting kernel from Legacy Image at 46000000 ... Image Name: ARM OpenWrt Linux-3.13.2 Created: 2014-02-27 14:18:25 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2371416 Bytes = 2.3 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 49000000 Booting using the fdt blob at 0x49000000 Loading Kernel Image ... OK Using Device Tree in place at 49000000, end 49006ee8 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.13.2 (yousong@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39135) ) #2 SMP PREEMPT Thu Feb 27 22:18:09 CST 2014 [ 0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Cubietech Cubieboard2 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0d1f000 s7040 r8192 d13440 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2 [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1034272K/1048576K available (3287K kernel code, 152K rwdata, 932K rodata, 178K init, 604K bss, 14304K reserved, 270336K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0426f2c (4220 kB) [ 0.000000] .init : 0xc0427000 - 0xc0453b80 ( 179 kB) [ 0.000000] .data : 0xc0454000 - 0xc047a2f8 ( 153 kB) [ 0.000000] .bss : 0xc047a2f8 - 0xc051159c ( 605 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns [ 0.000000] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns [ 0.000000] Console: colour dummy device 80x30 [ 0.000196] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448) [ 0.059908] pid_max: default: 32768 minimum: 301 [ 0.060088] Mount-cache hash table entries: 512 [ 0.060872] CPU: Testing write buffer coherency: ok [ 0.061183] /cpus/cpu@0 missing clock-frequency property [ 0.061201] /cpus/cpu@1 missing clock-frequency property [ 0.061214] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.061247] Setting up static identity map for 0x40011718 - 0x4001174c [ 0.120358] CPU1: failed to boot: -38 [ 0.120383] Brought up 1 CPUs [ 0.120390] SMP: Total of 1 processors activated. [ 0.120396] CPU: All CPU(s) started in SVC mode. [ 0.125075] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 [ 0.125337] pinctrl core: initialized pinctrl subsystem [ 0.125698] regulator-dummy: no parameters [ 0.126003] NET: Registered protocol family 16 [ 0.126303] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.132565] bio: create slab <bio-0> at 0 [ 0.133075] reg-fixed-voltage ahci-5v.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe [ 0.133103] platform ahci-5v.4: Driver reg-fixed-voltage requests probe deferral [ 0.133130] reg-fixed-voltage usb1-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe [ 0.133144] platform usb1-vbus.5: Driver reg-fixed-voltage requests probe deferral [ 0.133168] reg-fixed-voltage usb2-vbus.6: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe [ 0.133181] platform usb2-vbus.6: Driver reg-fixed-voltage requests probe deferral [ 0.133555] SCSI subsystem initialized [ 0.133984] usbcore: registered new interface driver usbfs [ 0.134034] usbcore: registered new interface driver hub [ 0.134148] usbcore: registered new device driver usb [ 0.134273] pps_core: LinuxPPS API ver. 1 registered [ 0.134281] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.134307] PTP clock support registered [ 0.135049] Switched to clocksource timer [ 0.140170] Clockevents: could not switch to one-shot mode: dummy_timer is not functional. [ 0.140193] Could not switch to high resolution mode on CPU 0 [ 0.140456] NET: Registered protocol family 2 [ 0.141209] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.141291] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.141412] TCP: Hash tables configured (established 8192 bind 8192) [ 0.141495] TCP: reno registered [ 0.141510] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.141568] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.141907] NET: Registered protocol family 1 [ 0.143081] audit: initializing netlink socket (disabled) [ 0.143127] type=2000 audit(0.130:1): initialized [ 0.143806] bounce pool size: 64 pages [ 0.149894] VFS: Disk quotas dquot_6.5.2 [ 0.150265] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.151830] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.151860] msgmni has been set to 1492 [ 0.153294] io scheduler noop registered [ 0.153308] io scheduler deadline registered [ 0.153344] io scheduler cfq registered (default) [ 0.155523] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.188217] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.210210] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A [ 0.731380] console [ttyS0] enabled [ 0.735855] Ring mode enabled [ 0.738917] No HW DMA feature register supported [ 0.743481] Normal descriptors [ 0.746804] Wake-Up On Lan supported [ 0.754164] libphy: stmmac: probed [ 0.757575] eth0: PHY ID 00008201 at 1 IRQ 0 (stmmac-0:01) active [ 0.763857] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.770421] sunxi-ehci: Allwinner sunXi EHCI driver [ 0.775448] platform 1c14000.ehci0: Driver sunxi-ehci requests probe deferral [ 0.782676] platform 1c1c000.ehci1: Driver sunxi-ehci requests probe deferral [ 0.789905] usbcore: registered new interface driver usb-storage [ 0.796140] mousedev: PS/2 mouse device common for all mice [ 0.802540] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 0.811139] sunxi-mci 1c0f000.mmc: base:0xf00b2000 irq:64 [ 0.817333] TCP: cubic registered [ 0.820735] Initializing XFRM netlink socket [ 0.825026] NET: Registered protocol family 17 [ 0.829559] 8021q: 802.1Q VLAN Support v1.8 [ 0.834045] Registering SWP/SWPB emulation handler [ 0.839181] registered taskstats version 1 [ 0.843893] ahci-5v: 5000 mV [ 0.847174] usb1-vbus: 5000 mV [ 0.850687] usb2-vbus: 5000 mV [ 0.854091] sunxi-ehci 1c14000.ehci0: EHCI Host Controller [ 0.859596] sunxi-ehci 1c14000.ehci0: new USB bus registered, assigned bus number 1 [ 0.867393] sunxi-ehci 1c14000.ehci0: irq 71, io mem 0x01c14000 [ 0.890154] sunxi-ehci 1c14000.ehci0: USB 2.0 started, EHCI 1.00 [ 0.896372] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.903200] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.910428] usb usb1: Product: EHCI Host Controller [ 0.915302] usb usb1: Manufacturer: Linux 3.13.2 ehci_hcd [ 0.920726] usb usb1: SerialNumber: 1c14000.ehci0 [ 0.925895] hub 1-0:1.0: USB hub found [ 0.929725] hub 1-0:1.0: 1 port detected [ 0.934181] sunxi-ehci 1c1c000.ehci1: EHCI Host Controller [ 0.939684] sunxi-ehci 1c1c000.ehci1: new USB bus registered, assigned bus number 2 [ 0.947475] sunxi-ehci 1c1c000.ehci1: irq 72, io mem 0x01c1c000 [ 0.970150] sunxi-ehci 1c1c000.ehci1: USB 2.0 started, EHCI 1.00 [ 0.976310] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.983109] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.991356] usb usb2: Product: EHCI Host Controller [ 0.997260] usb usb2: Manufacturer: Linux 3.13.2 ehci_hcd [ 1.002668] usb usb2: SerialNumber: 1c1c000.ehci1 [ 1.007795] hub 2-0:1.0: USB hub found [ 1.011603] hub 2-0:1.0: 1 port detected [ 1.015844] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.022932] Waiting for root device /dev/mmcblk0p2... [ 1.061974] sunxi-mci 1c0f000.mmc: smc 0 err, cmd 8, RTO !! [ 1.211954] sunxi-mci 1c0f000.mmc: smc 0 err, cmd 8, RTO !! [ 1.235781] mmc0: SD Status: Invalid Allocation Unit size. [ 1.450146] mmc0: new high speed SD card at address b368 [ 1.455856] isa bounce pool size: 16 pages [ 1.460086] mmcblk0: mmc0:b368 SD256 244 MiB [ 1.465741] mmcblk0: p1 p2 [ 1.571049] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 1.579767] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 1.593724] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 1.601966] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 1.608971] Freeing unused kernel memory: 176K (c0427000 - c0453000) procd: Console is alive procd: - watchdog - procd: - preinit - probing /dev/mmcblk0 for uboot env data [ 1.892334] sunxi-ahci 1c18000.ahci: controller can't do PMP, turning off CAP_PMP [ 1.903236] sunxi-ahci 1c18000.ahci: forcing PORTS_IMPL to 0x1 [ 1.909092] sunxi-ahci 1c18000.ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl sunxi mode Detected generic sunxi // generic sunxi[ 1.939684] sunxi-ahci 1c18000.ahci: flags: ncq sntf pm led clo only pio slum part ccc [ 1.957231] scsi0 : sunxi_ahci [ 1.963574] random: mktemp urandom read with 19 bits of entropy available [ 1.971066] ata1: SATA max UDMA/133 irq 88 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 2.320165] ata1: SATA link down (SStatus 0 SControl 300) mount_root: mounting /dev/root [ 5.099990] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 7.109435] NET: Registered protocol family 10 [ 7.130439] nf_conntrack version 0.5.0 (16163 buckets, 64652 max) [ 7.160431] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 7.202011] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0 [ 7.208806] sunxi-rtc 1c20d00.rtc: RTC enabled [ 7.232073] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.372898] xt_time: kernel timezone is -0000 [ 7.383574] PPP generic driver version 2.4.2 [ 7.399322] NET: Registered protocol family 24 [ 8.584265] random: nonblocking pool is initialized procd: - init complete - BusyBox v1.19.4 (2014-02-27 21:24:43 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r39756) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#