COMFAST CF-EW72 V2

COMFAST CF-EW72 V2 Vendor image

Dual-gigabit dual-band PoE-powered outdoor device with IP66° protection with up to 1200Mbps°° wireless bandwidth.

Can be used as router, wireless repeater or wireless access point.

°: Even though it claims IP66 protection, it doesn't appear to be. Rain can leak into if positioned bottom-up, and raindrops may be blowed into with wind.

°°: 1200Mbps is sum of total bandwidth 300 Mbps at 2.4 GHz + 867 Mbps at 5 GHz

Supported Versions

COMFAST CF-EW72 without version is completely different device.

Please, look for Model at the label on your device. If it says CF-EW72 V2, you should proceed with this page. If there is no V2 you should proceed to COMFAST CF-EW72

Hardware Highlights

Installation

You will need 2 ethernet cables for this.

  1. → Connect bundled PoE Injector to electricity.
  2. → Connect your PC to the LAN port of bundled PoE injector with first ethernet cable.
  3. → Configure static IP on your computer's ethernet adapter
    • IP : 192.168.1.x (x is 2 to 254)
    • MASK : 255.255.255.0
    • Gateway : empty
    • DNS : empty
  4. → Plug second ethernet cable to the PoE port of bundled PoE injector.
  5. → Press and hold pressed ⚫reset button on COMFAST CF-EW72 V2 (reset button is between LAN and WAN ports) and plug second ethernet cable from bundled injector's PoE port to LAN port of COMFAST CF-EW72 V2.
  6. → 🔵POWER and 🔵LAN LEDs will turn on, 🔵Wi-Fi LED will blink 10 times in 10 seconds, then for 1 second it will blink rapidly, then it will stay on.
  7. → Release the ⚫reset button.
  8. → Go to browser and navigate to http://192.168.1.1, you will see Mediatek U-Boot System Recovery Mode.
  9. → Click Upload and choose *-factory.bin firmware file.
  10. → Proceed.
  11. → COMFAST CF-EW72 V2 will start blinking with 🔵Wi-Fi LED, until it will flash new firmware, and reboot.

Flash Layout

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

OEM easy installation

  1. → Unpack OEM firmware archive to get .bin file.
  2. → Flash it the same way you flash OpenWRT.

OEM installation using the TFTP method

→ generic.flashing.tftp

Upgrading OpenWrt

→ generic.sysupgrade

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

Debricking

Same as Installing OpenWRT.

Failsafe mode

→ failsafe_and_factory_reset

Basic configuration

COMFAST CF-EW72 V2 is usually used as Dumb access point, not a router.

Configure as DUMB ACCESS POINT:

Configure as ROUTER:

Specific Configuration

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi 192.168.1.1/24
wan (eth1.1) EXAMPLE WAN port DHCP
wlan0 WiFi 2.4GHz Disabled
wlan1 WiFi 5GHz Disabled

</WRAP>

Switch Ports (for VLANs)

Port Switch port
Internet (WAN) 0
LAN 1 1

Buttons

The only button is ⚫reset button.

LEDs

Device has 8 blue leds onboard, but some of them are not visible as shell does not have holes for them. The only both visible and customizable led is Wi-Fi led.

Led # Indicator role GPIO Name in LuCI Note
1 🔵POWER N\A N\A Always on when device is powered. Can not be controlled programmatically.
2 🔷Not visible 13 blue:hidden_led_2 This led has no hole in shell. Controllable with GPIO.
3 🔵WAN N\A N\A Indicates WAN activity. Can not be controlled programmatically.
4 🔷Not visible 16 blue:hidden_led_4 This led has no hole in shell. Controllable with GPIO.
5 🔵LAN N\A N\A Indicates LAN activity. Can not be controlled programmatically.
6 ⬛Not visible N\A N\A This led has no hole in shell. Can not be controlled programmatically.
7 🔵WLAN 15 blue:wlan Indicates Wi-Fi activity. Can be controlled programmatically. By default, not bound to any wireless adapter
8 ⬛Not visible N\A N\A This led has no hole in shell. Can not be controlled programmatically.

Hardware

Info

Power

Device is powered only through PoE 802.3af (“active PoE”) and bundled with 220v PoE injector.

:!: There is no information if device can be powered with “Passive PoE”.

:!: There is no PoE Passthrough: please note that device does not provide power to daisy-chained device.

MT7621AT or MT7621DAT

For end user, there is no difference.

COMFAST CF-EW72 V2 is known to be produced in two variants (not versions):

  • COMFAST CF-EW72 V2 with MT7621AT and separate DDR RAM chip onboard.
  • COMFAST CF-EW72 V2 with MT7621DAT with integrated RAM and no DDR RAM soldered chip onboard.

PCBs for both variants seem to be same. Firmware works for both.

COMFAST CF-EW72 V2 known to be sold both in unpainted cardboard box and colorful glossy cardboard box. I guess, but not guarantee that colorful box is for new variant equipped with MT7621DAT SoC and no RAM chip. Seems that devices also have different factory labels.

Photos

Photo of casing

Front Back Opened Lid
cf-ew72-v2_casing_front.jpg cf-ew72-v2_casing_back.jpg cf-ew72-v2_casing_no_lid.jpg

Photo of backside label

Variant for MT7621AT Variant for MT7621DAT
cf-ew72-v2_label_v2.1.jpg cf-ew72-v2_label_v2.2.jpg

Photo of PCB

Click to enlarge

Side A Side B
cf-ew72-v2_pcb-front.jpg cf-ew72-v2_pcb-back.jpg

Photo of bundled PoE Injector

Click to enlarge

PoE Injector
Front 		PoE Injector
Back 		PoE Injector
Label
cf-ew72-v2_poe-injector_front.jpg cf-ew72-v2_poe-injector_back.jpg cf-ew72-v2_poe-injector_label.jpg

Opening the case

Tools needed

  • Hot air gun (to gently remove factory sticker)
  • Needle nose pilers
  • PH0 screwdriver
  • Сontainer for small items (zip bag)

Opening the case in steps

Step Text Image
1 Open the case and disconnect cables. Click image
to enlarge
2 Use hot air to heat the factory label and peel it off.
If you wish, glue it to the back of the case, closer to the antennas. 		cf-ew72-v2_disassembly_10_remove_sticker.jpg
3 Remove 2 screws hidden under the factory label. cf-ew72-v2_disassembly_20_remove_screws.jpg
4 Unscrew antennas.
Remove big rubber rings.
Unscrew the nuts from the Wi-Fi antenna connectors using thin-nosed pliers.
Do not remove washer and o-ring hidden under washer yet. 		cf-ew72-v2_disassembly_30_remove_antennas_and_nuts.jpg
5 Grasp the sides of the device and gently push the antenna connectors into the device.
Be careful with the center pin of the connector.
After the antenna connectors are completely inside the device, pull on the plastic insert with RJ45 connectors. 		cf-ew72-v2_disassembly_40_push_pcb_out.jpg
6 Remove 2 washers and 4 o-rings in total.
There are 2 washers and 2 small o-rings on the outside of the case.
:!: There are two more small o-rings on Wi-Fi antenna connectors from the inside of the case.
They may be on antenna connectors or stick to casing from inside. Remove them.
7 Put into a zip bag:
☑️ 1 factory label (if removed)
☑️ 2 screws
☑️ 2 big rubber rings
☑️ 2 nuts
☑️ 2 washers
☑️ 4 small o-rings
8 Put a zip bag inside an empty casing and close with a casing lid.
9 Screw antennas to Wi-Fi connectors on PCB.

Serial

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

  • Remove the case.
  • Device has factory-soldered 4 x 2.54mm pin header (VCC, GND, TX, RX).
  • GND pin is recommended to be connected.
  • :!: It is recommended NOT connect VCC pin as device powers from PoE.
  • :!: It is recommended to connect serial adapter through active (with separate power) USB hub. Avoid connecting to usb port connected to computer motherboard. CF-EW72 V2 has 48V on PCB, and if 48V will somehow hit your USB, it may damage your PC, including CPU.
  • In some situations device may not start when RX pin is connected - so, connect it right after you see output from device.
  • Connected RX also may cause random 5GHz Wi-Fi chip problems.
Serial connection parameters
for COMFAST CF-EW72 V2 		115200, 8N1, 3.3V

Bootloader mods

→ bootloader

Hardware mods

None so far.

Bootlogs

OEM bootlog

U-Boot 2018.09-gbef8015-dirty (Dec 09 2020 - 06:28:07 -0500) CPU: MediaTek MT7621AT ver 1, eco 3 Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz Model: MediaTek MT7621 reference board DRAM: 128 MiB Loading Environment from SPI Flash... SF: Detected mx25l12805 with page size 256 Bytes, erase size 64 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: uartlite0@1e000c00 Out: uartlite0@1e000c00 Err: uartlite0@1e000c00 Net: Warning: eth@1e100000 (eth0) using random MAC address - 5e:69:c8:f8:cf:5b eth0: eth@1e100000 Hit any key to stop autoboot: 0 Using eth@1e100000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'firmware_auto.bin'. Load address: 0x80010000 Loading: * ARP Retry count exceeded; starting again *** TFTP client failure: -110 *** *** Operation Aborted! *** *** U-Boot Boot Menu *** 1. Startup system (Default) 2. Upgrade firmware 3. Upgrade bootloader 4. Upgrade bootloader (advanced mode) 5. Load image 0. U-Boot console Press UP/DOWN to move, ENTER to select ## Booting kernel from Legacy Image at bfc50000 ... Image Name: MIPS LEDE Linux-4.4.198 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1753284 Bytes = 1.7 MiB Load Address: 81001000 Entry Point: 81001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK [ 0.000000] Linux version 4.4.198 (luojiaqiang@comfast-devel-machine) (gcc version 5.5.0 (LEDE GCC 5.5.0 r429-2c4d696a) ) #0 SMP Tue Mar 2 00:47:59 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is COMFAST CF-A560V2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 10 pages/cpu @81693000 s8544 r8192 d24224 u40960 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00020842 [ 0.000000] Readback ErrCtl register=00020842 [ 0.000000] Memory: 124060K/131072K available (4112K kernel code, 203K rwdata, 904K rodata, 208K init, 201K bss, 7012K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007777] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.070402] pid_max: default: 32768 minimum: 301 [ 0.075114] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.081639] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 1.680918] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 1.680928] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 1.680939] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 1.681088] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.177572] Synchronize counters for CPU 1: done. [ 1.463681] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 1.463687] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 1.463695] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 1.463763] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.267948] Synchronize counters for CPU 2: done. [ 1.553789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 1.553795] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 1.553801] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 1.553882] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.353127] Synchronize counters for CPU 3: done. [ 0.357866] Brought up 4 CPUs [ 0.365395] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.375186] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.381493] pinctrl core: initialized pinctrl subsystem [ 0.387245] NET: Registered protocol family 16 [ 0.427016] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.432679] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.438280] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.444445] mt7621-pci 1e140000.pcie: Failed to get gpio for PCIe1 [ 0.450571] mt7621-pci 1e140000.pcie: Failed to get gpio for PCIe2 [ 1.057708] PCIe port 2 link down [ 1.060937] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.100537] PCI host bridge to bus 0000:00 [ 1.104575] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.111423] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.118215] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 1.124967] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.133638] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.141572] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.150969] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.157678] pci 0000:00:01.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 1.164834] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] [ 1.171585] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] [ 1.178314] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 1.185060] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.189970] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.196731] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 1.204417] pci 0000:02:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 1.212120] pci 0000:02:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 1.219791] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.224716] pci 0000:00:01.0: bridge window [mem 0x60100000-0x602fffff pref] [ 1.233607] clocksource: Switched to clocksource GIC [ 1.240339] NET: Registered protocol family 2 [ 1.245476] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.252351] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.258689] TCP: Hash tables configured (established 1024 bind 1024) [ 1.265046] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.270792] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.277293] NET: Registered protocol family 1 [ 1.295994] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.301749] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.314629] io scheduler noop registered [ 1.318469] io scheduler deadline registered (default) [ 1.325148] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 1.332433] console [ttyS0] disabled [ 1.336021] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 33, base_baud = 3125000) is a 16550A [ 1.345004] console [ttyS0] enabled [ 1.345004] console [ttyS0] enabled [ 1.351893] bootconsole [early0] disabled [ 1.351893] bootconsole [early0] disabled [ 1.360373] 1e000d00.uartfull: ttyS1 at MMIO 0x1e000d00 (irq = 34, base_baud = 3125000) is a 16550A [ 1.371596] mt7621_wdt 1e000100.wdt: Initialized [ 1.377570] m25p80 spi32766.0: mx25l12805d (16384 Kbytes) [ 1.383017] 4 ofpart partitions found on MTD device spi32766.0 [ 1.388909] Creating 4 MTD partitions on "spi32766.0": [ 1.394087] 0x000000000000-0x000000030000 : "Bootloader" [ 1.400828] 0x000000030000-0x000000040000 : "Config" [ 1.407109] 0x000000040000-0x000000050000 : "factory" [ 1.413412] 0x000000050000-0x000001000000 : "firmware" [ 1.440834] no rootfs found after FIT image in "firmware" [ 1.488034] 2 uimage-fw partitions found on MTD device firmware [ 1.493991] 0x000000050000-0x0000001fc104 : "kernel" [ 1.500144] 0x0000001fc104-0x000001000000 : "rootfs" [ 1.506221] mtd: device 5 (rootfs) set to be root filesystem [ 1.511972] 1 squashfs-split partitions found on MTD device rootfs [ 1.518189] 0x000000900000-0x000001000000 : "rootfs_data" [ 1.525227] libphy: Fixed MDIO Bus: probed [ 1.563842] libphy: mdio: probed [ 1.568120] mtk_soc_eth 1e100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.579325] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 10 [ 1.588366] mtk_soc_eth 1e100000.ethernet: connected mac 1 to PHY at fixed-0:01 [uid=00000000, driver=Generic PHY] [ 1.599549] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 10 [ 1.610379] NET: Registered protocol family 10 [ 1.616297] NET: Registered protocol family 17 [ 1.620817] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.633476] 8021q: 802.1Q VLAN Support v1.8 [ 1.673710] mt753x gsw: Switch is MediaTek MT7530 rev 1 [ 1.700425] libphy: mt753x_mdio: probed [ 1.710371] hctosys: unable to open rtc device (rtc0) [ 1.724415] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.732012] Freeing unused kernel memory: 208K [ 1.736501] This architecture does not have kernel memory protection. [ 2.402888] init: Console is alive [ 2.406621] init: - watchdog - [ 4.522346] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.631201] Ralink/MTK WiFi EEPROM API Driver loaded. [ 4.645159] SCSI subsystem initialized [ 4.656464] mediatek_soc_hnat 1e100000.hnat: wan = eth1 [ 4.661707] mediatek_soc_hnat 1e100000.hnat: ppd = eth0 [ 4.666977] mediatek_soc_hnat 1e100000.hnat: gmac num = 2 [ 4.672377] mediatek_soc_hnat 1e100000.hnat: foe etry num cfg = 2 [ 4.679910] mediatek_soc_hnat 1e100000.hnat: FOE entry number = 4096 [ 4.686914] mediatek_soc_hnat 1e100000.hnat: hwnat start [ 4.692957] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.703944] init: - preinit - [ 4.981039] mt753x gsw: Port 1 Link is Up - 1Gbps/Full [ 4.989392] random: procd: uninitialized urandom read (4 bytes read, 95 bits of entropy available) ifconfig: SIOCSIFHWADDR: Cannot assign requested address [ 5.674991] random: mktemp: uninitialized urandom read (6 bytes read, 117 bits of entropy available) [ 5.689012] random: mktemp: uninitialized urandom read (6 bytes read, 117 bits of entropy available) [ 5.702996] random: mktemp: uninitialized urandom read (6 bytes read, 118 bits of entropy available) Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.865818] random: nonblocking pool is initialized [ 7.929604] jffs2: notice: (489) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 7.947147] mount_root: switching to jffs2 overlay [ 7.962571] urandom-seed: Seeding with /etc/urandom.seed [ 8.152700] procd: - early - [ 8.155812] procd: - watchdog - [ 8.803769] procd: - watchdog - [ 8.807238] procd: - ubus - [ 8.867095] procd: - init - Please press Enter to activate this console. [ 9.201703] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.234997] Initializing XFRM netlink socket [ 9.241044] NET: Registered protocol family 15 [ 9.250415] l2tp_core: L2TP core driver, V2.0 [ 9.256030] l2tp_netlink: L2TP netlink interface [ 9.265991] gre: GRE over IPv4 demultiplexor driver [ 9.272692] ip_gre: GRE over IPv4 tunneling driver [ 9.284320] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.298658] Netfilter messages via NETLINK v0.30. [ 9.307810] ip_set: protocol 6 [ 9.347596] i2c /dev entries driver [ 9.364863] u32 classifier [ 9.367626] input device check on [ 9.371344] Actions configured [ 9.377705] Mirror/redirect action on [ 9.393647] nf_conntrack version 0.5.0 (1941 buckets, 7764 max) [ 10.287324] register mt_drv [ 10.295756] [ 10.295756] [ 10.295756] === pAd = c0801000, size = 2175376 === [ 10.295756] [ 10.305348] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x [ 10.312017] <-- RTMPAllocAdapterBlock, Status=0 [ 10.316568] pAd->CSRBaseAddress =0xc0700000, csr_addr=0xc0700000! [ 10.322663] device_id =0x7603 [ 10.325651] RtmpChipOpsHook(474): Not support for HIF_MT yet! [ 10.331393] mt7603_init()--> [ 10.334288] mt_bcn_buf_init(224): Not support for HIF_MT yet! [ 10.340028] <--mt7603_init() [ 10.343172] match_index_by_chipname() MT7603 found as INDEX0 [ 10.348914] l1set_profile_path() profile update from /etc/wireless/mt7603e/mt7603.dat to /tmp/profiles/rt2860v2_2g.dat [ 10.359682] l1set_eeprom_offset() eeprom offset remain 0x0 [ 10.365218] l1set_eeprom_size() eeprom size remain 0x200 [ 10.370554] l1set_ifname() ifname rename from ra0 to ra [ 10.375790] l1set_ifname() ifname remain ra [ 10.379998] l1set_ifname() ifname remain ra [ 10.384224] l1set_ifname() ifname remain apcli [ 12.416403] register mt7663 [ 12.431205] [ 12.431205] [ 12.431205] === pAd = c1001000, size = 4880672 === [ 12.431205] [ 12.441368] <-- RTMPAllocAdapterBlock, Status=0 [ 12.445956] pAd->PciHif.CSRBaseAddress =0xc0f00000, csr_addr=0xc0f00000! [ 12.452664] RTMPInitPCIeDevice():device_id=0x7663 [ 12.457390] mt_pci_chip_cfg(): HWVer=0x8b10, FWVer=0x8a01, pAd->ChipID=0x7663 [ 12.464550] mt7663_init()--> [ 12.467444] <--mt7663_init() [ 12.471379] <-- RTMPAllocTxRxRingMemory, Status=0 [ 12.476151] get_wdev_by_idx: invalid idx(0) [ 12.480341] get_wdev_by_idx: invalid idx(0) [ 12.485715] get_wdev_by_idx: invalid idx(0) [ 12.489903] get_wdev_by_idx: invalid idx(0) [ 12.494113] get_wdev_by_idx: invalid idx(0) [ 12.498293] get_wdev_by_idx: invalid idx(0) [ 12.503680] get_wdev_by_idx: invalid idx(0) [ 12.563907] Bridge firewalling registered [ 12.581813] Ebtables v2.0 registered [ 12.588902] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.698499] get_wdev_by_idx: invalid idx(0) [ 12.708594] get_wdev_by_idx: invalid idx(0) [ 12.877007] xt_time: kernel timezone is -0000 [ 12.901172] PPP generic driver version 2.4.2 [ 12.906684] PPP MPPE Compression module registered [ 12.912693] NET: Registered protocol family 24 [ 12.918485] PPTP driver version 0.8.5 [ 12.926466] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 12.933970] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.709577] sysctl (959): drop_caches: 3 [ 16.085152] mt753x gsw: Port 1 Link is Up - 1Gbps/Full [ 18.569500] get_wdev_by_idx: invalid idx(0) [ 19.069971] device eth1.1 entered promiscuous mode [ 19.074848] device eth1 entered promiscuous mode [ 19.087363] br-lan: port 1(eth1.1) entered forwarding state [ 19.093101] br-lan: port 1(eth1.1) entered forwarding state [ 19.135378] device eth1.2 entered promiscuous mode [ 19.157945] br-wan: port 1(eth1.2) entered forwarding state [ 19.163707] br-wan: port 1(eth1.2) entered forwarding state [ 20.533502] get_wdev_by_idx: invalid idx(0) [ 20.543750] get_wdev_by_idx: invalid idx(0) [ 21.083620] br-lan: port 1(eth1.1) entered forwarding state [ 21.163605] br-wan: port 1(eth1.2) entered forwarding state [ 22.064711] get_wdev_by_idx: invalid idx(0) [ 22.069118] get_wdev_by_idx: invalid idx(0) [ 23.084156] get_wdev_by_idx: invalid idx(0) [ 23.088394] get_wdev_by_idx: invalid idx(0) [ 24.094128] get_wdev_by_idx: invalid idx(0) [ 24.098365] get_wdev_by_idx: invalid idx(0) [ 25.104083] get_wdev_by_idx: invalid idx(0) [ 25.108314] get_wdev_by_idx: invalid idx(0) [ 26.114136] get_wdev_by_idx: invalid idx(0) [ 26.118371] get_wdev_by_idx: invalid idx(0) [ 27.124111] get_wdev_by_idx: invalid idx(0) [ 27.128350] get_wdev_by_idx: invalid idx(0) [ 28.134069] get_wdev_by_idx: invalid idx(0) [ 28.138296] get_wdev_by_idx: invalid idx(0) [ 29.144065] get_wdev_by_idx: invalid idx(0) [ 29.148292] get_wdev_by_idx: invalid idx(0) [ 30.154065] get_wdev_by_idx: invalid idx(0) [ 30.158293] get_wdev_by_idx: invalid idx(0) [ 30.925439] rai0: ===> main_virtual_if_open [ 30.929649] get_wdev_by_idx: invalid idx(0) [ 30.933885] get_wdev_by_idx: invalid idx(0) [ 30.938072] get_wdev_by_idx: invalid idx(0) [ 30.942251] get_wdev_by_idx: invalid idx(0) [ 30.947537] get_wdev_by_idx: invalid idx(0) [ 30.951790] get_wdev_by_idx: invalid idx(0) [ 33.975763] SSID[0]=COMFAST_6556_5G, EdcaIdx=0 [ 33.982049] cfg_mode=14 [ 33.984609] cfg_mode=14 [ 33.987059] cfg_mode=14 [ 33.989512] wmode_band_equal(): Band Equal! [ 33.993897] auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 34.002340] BssIdx(0) wdev->channel=149 [ 34.006239] BssIdx(1) wdev->channel=149 [ 34.010076] BssIdx(2) wdev->channel=149 [ 34.013965] BssIdx(3) wdev->channel=149 [ 34.017803] BssIdx(4) wdev->channel=149 [ 34.021635] BssIdx(5) wdev->channel=149 [ 34.025530] BssIdx(6) wdev->channel=149 [ 34.029367] BssIdx(7) wdev->channel=149 [ 34.033199] Index0 Channel=149 [ 34.037302] BandSteering=0 [ 34.040274] [TxPower] BAND0: 100 [ 34.043853] [SKUenable] BAND0: 0 [ 34.047346] [PERCENTAGEenable] BAND0: 0 [ 34.051261] [BFBACKOFFenable] BAND0: 0 [ 34.055721] profile: FragThreshold[0]=2346 [ 34.060087] APEdca0 [ 34.062362] APEdca1 [ 34.064720] APEdca2 [ 34.067000] APEdca3 [ 34.077992] DfsZeroWait Support=0/0 [ 34.082446] DfsZeroWaitCacTime=255/255 [ 34.086823] read_itxbf: ITxBfEn = 1 [ 34.090310] read_itxbf: BSSID[0] [ 34.093579] read_itxbf: MBSS[0] ITxBfEn = 1 [ 34.097768] read_itxbf: More BSSID[1] [ 34.101427] read_itxbf: More MBSS[1] ITxBfEn = 1 [ 34.106074] read_itxbf: More BSSID[2] [ 34.109741] read_itxbf: More MBSS[2] ITxBfEn = 1 [ 34.114392] read_itxbf: More BSSID[3] [ 34.118059] read_itxbf: More MBSS[3] ITxBfEn = 1 [ 34.122671] read_itxbf: More BSSID[4] [ 34.126366] read_itxbf: More MBSS[4] ITxBfEn = 1 [ 34.130986] read_itxbf: More BSSID[5] [ 34.134683] read_itxbf: More MBSS[5] ITxBfEn = 1 [ 34.139304] read_itxbf: More BSSID[6] [ 34.142962] read_itxbf: More MBSS[6] ITxBfEn = 1 [ 34.147611] read_itxbf: More BSSID[7] [ 34.151278] read_itxbf: More MBSS[7] ITxBfEn = 1 [ 34.155984] read_itxbf: Common.ITxBfEn = 1 [ 34.160193] read_etxbf: ETxBfEnCond = 1 [ 34.164073] read_etxbf: BSSID[0] [ 34.167307] read_etxbf: MBSS[0] ETxBfEnCond = 1 [ 34.171834] read_etxbf: More BSSID[1] [ 34.175527] read_etxbf: More MBSS[1] ETxBfEnCond = 1 [ 34.180496] read_etxbf: More BSSID[2] [ 34.184191] read_etxbf: More MBSS[2] ETxBfEnCond = 1 [ 34.189159] read_etxbf: More BSSID[3] [ 34.192819] read_etxbf: More MBSS[3] ETxBfEnCond = 1 [ 34.197814] read_etxbf: More BSSID[4] [ 34.201481] read_etxbf: More MBSS[4] ETxBfEnCond = 1 [ 34.206483] read_etxbf: More BSSID[5] [ 34.210152] read_etxbf: More MBSS[5] ETxBfEnCond = 1 [ 34.215150] read_etxbf: More BSSID[6] [ 34.218817] read_etxbf: More MBSS[6] ETxBfEnCond = 1 [ 34.223818] read_etxbf: More BSSID[7] [ 34.227492] read_etxbf: More MBSS[7] ETxBfEnCond = 1 [ 34.233165] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [ 34.270836] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [ 34.276580] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [ 34.282301] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [ 34.300238] HT: WDEV[0] Ext Channel = ABOVE [ 34.304710] HT: greenap_cap = 0 [ 34.335802] WtcSetMaxStaNum: MaxStaNum:100, BssidNum:8, WdsNum:0, ApcliNum:1, MaxNumChipRept:24, MinMcastWcid:126 [ 34.346160] Top Init Done! [ 34.348873] Use dev_alloc_skb [ 34.352754] RX[0] DESC a0f2c000 size = 2048 [ 34.357253] RX[1] DESC a0f2d000 size = 2048 [ 34.361598] cut_through_init(): ct sw token number = 2047 [ 34.367290] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/2048 [ 34.375071] cut_through_token_list_init(): 80ec3688,80ec3688 [ 34.380975] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/2048 [ 34.388754] cut_through_token_list_init(): 80ec3698,80ec3698 [ 34.394490] Hif Init Done! [ 34.397203] ctl->txq = c14a2dd0 [ 34.400338] ctl->rxq = c14a2ddc [ 34.403473] ctl->ackq = c14a2de8 [ 34.406730] ctl->kickq = c14a2df4 [ 34.410050] ctl->tx_doneq = c14a2e00 [ 34.413658] ctl->rx_doneq = c14a2e0c [ 34.417299] mt7663_fw_prepare():using E2 ROM patch [ 34.422087] mt7663_fw_prepare():using E2 firmware [ 34.426858] Parsing patch header [ 34.430089] Built date: 2009041715da1a1 [ 34.434113] [ 34.435600] Platform: 7663 [ 34.438404] HW/SW version: 0x65322d31 [ 34.442172] Patch version: 0x3830328a [ 34.445986] Target address: 0xdc000, length: 211488 [ 34.451104] patch is not ready && get semaphore success [ 34.456398] Start address = 0xdc000, DL length = 211488, Data mode = 0x80000000 [ 34.463863] EventGenericEventHandler: CMD Success [ 34.468613] MtCmdAddressLenReq:(ret = 0) [ 34.474770] MtCmdPatchFinishReq [ 34.478820] EventGenericEventHandler: CMD Success [ 34.483804] release patch semaphore [ 34.487316] Parsing CPU 0 fw tailer [ 34.490803] Chip ID: 0x08 [ 34.493573] Eco version: 0x01 [ 34.496644] Region number: 0x03 [ 34.499878] Format version: 0x02 [ 34.503197] Format flag: 0x01 [ 34.506335] Ram version: 7663mp1827 [ 34.509944] Built date: 20200904171623 [ 34.513967] Common crc: 0xa3c3110b [ 34.517452] Parsing tailer region 0 [ 34.520935] Decomp crc: 0x0 [ 34.523850] Decomp size: 0x0 [ 34.526819] Decomp block size: 0x0 [ 34.530303] Target address: 0x112c00 [ 34.533997] Download size: 273584 [ 34.537400] Feature set: 0x27 [ 34.540462] Parsing tailer region 1 [ 34.543987] Decomp crc: 0x0 [ 34.546877] Decomp size: 0x0 [ 34.549839] Decomp block size: 0x0 [ 34.553321] Target address: 0x2018400 [ 34.557137] Download size: 57616 [ 34.560456] Feature set: 0x07 [ 34.563518] Parsing tailer region 2 [ 34.567045] Decomp crc: 0x0 [ 34.569922] Decomp size: 0x0 [ 34.572883] Decomp block size: 0x0 [ 34.576395] Target address: 0x40100000 [ 34.580227] Download size: 14736 [ 34.583559] Feature set: 0x07 [ 34.586630] Release info: header tag = 0, total length = 88 [ 34.592288] tag 1, padding length = 1, tag length = 83 [ 34.597533] payload: t-neptune-main-mt7663e2-1949-MT7663_E2_ASIC_ROM_RAM_Retail_Broadband-20200904171503 [ 34.607426] Start address = 0x112c00, DL length = 273584, Data mode = 0x8000000f [ 34.614952] EventGenericEventHandler: CMD Success [ 34.619686] MtCmdAddressLenReq:(ret = 0) [ 34.626723] Start address = 0x2018400, DL length = 57616, Data mode = 0x8000000f [ 34.634363] EventGenericEventHandler: CMD Success [ 34.639110] MtCmdAddressLenReq:(ret = 0) [ 34.643763] Start address = 0x40100000, DL length = 14736, Data mode = 0x8000000f [ 34.651353] EventGenericEventHandler: CMD Success [ 34.656127] MtCmdAddressLenReq:(ret = 0) [ 34.660222] MtCmdFwStartReq: override = 0x1, address = 0x112c00 [ 34.705622] EventGenericEventHandler: CMD Success [ 34.710371] MCU Init Done! [ 34.713084] efuse_probe: efuse = 511161 [ 34.716951] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 34.722356] RtmpEepromGetDefault::e2p_dafault=1 [ 34.726918] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 34.734518] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x8000] [ 34.740530] EEPROM:Read from [factory] offset 0x8000,length 0x800. [ 34.748518] validFlashEepromID(): eeFlashId=7663, pAd->ChipID=7663 [ 36.387054] Country Region from e2p = 0 [ 36.390912] mt7663_antenna_default_reset() todo [ 36.395504] RTMPReadTxPwrPerRate(444): Don't Support this now! [ 36.401345] RcRadioInit(): DbdcMode=0, ConcurrentBand=1 [ 36.406617] RcRadioInit(): pRadioCtrl=87d2ad1c,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 36.415103] AntCfgInit(2996): Not support for HIF_MT yet! [ 36.420521] MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! [ 36.426219] MtReadPwrLimitTable: SKU Path: /etc/wireless/mediatek/mt7613e/SingleSKU.dat [ 36.436481] MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! [ 36.442149] MtReadPwrLimitTable: SKU Path: /etc/wireless/mediatek/mt7613e/SingleSKU_BF.dat [ 36.500270] EEPROM Init Done! [ 36.503274] mt_mac_init()--> [ 36.506241] mt_mac_pse_init(2995): Don't Support this now! [ 36.511729] mt7663_init_mac_cr()--> [ 36.515290] mt7663_init_mac_cr(): TMAC_TRCR0=0x82783c92 [ 36.520532] MtAsicSetMacMaxLen(1075): Not support for HIF_MT yet! [ 36.526660] <--mt_mac_init() [ 36.534393] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 36.542592] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 36.550838] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 36.557437] MAC Init Done! [ 36.560157] MT7663BBPInit():BBP Initialization..... [ 36.565085] Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 [ 36.574178] Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 [ 36.583221] MT7663BBPInit() todo [ 36.586481] PHY Init Done! [ 36.591496] SSID[0]=COMFAST_6556_5G, EdcaIdx=0 [ 36.597815] cfg_mode=14 [ 36.600261] cfg_mode=14 [ 36.602702] cfg_mode=14 [ 36.605202] wmode_band_equal(): Band Equal! [ 36.609495] auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 36.617970] BssIdx(0) wdev->channel=149 [ 36.621803] BssIdx(1) wdev->channel=149 [ 36.625660] BssIdx(2) wdev->channel=149 [ 36.629493] BssIdx(3) wdev->channel=149 [ 36.633322] BssIdx(4) wdev->channel=149 [ 36.637175] BssIdx(5) wdev->channel=149 [ 36.641007] BssIdx(6) wdev->channel=149 [ 36.644863] BssIdx(7) wdev->channel=149 [ 36.648695] Index0 Channel=149 [ 36.652708] BandSteering=0 [ 36.655703] [TxPower] BAND0: 100 [ 36.659193] [SKUenable] BAND0: 0 [ 36.662681] [PERCENTAGEenable] BAND0: 0 [ 36.666637] [BFBACKOFFenable] BAND0: 0 [ 36.671002] profile: FragThreshold[0]=2346 [ 36.675393] APEdca0 [ 36.677671] APEdca1 [ 36.679945] APEdca2 [ 36.682219] APEdca3 [ 36.693148] DfsZeroWait Support=0/0 [ 36.697627] DfsZeroWaitCacTime=255/255 [ 36.701932] read_itxbf: ITxBfEn = 1 [ 36.705440] read_itxbf: BSSID[0] [ 36.708666] read_itxbf: MBSS[0] ITxBfEn = 1 [ 36.712843] read_itxbf: More BSSID[1] [ 36.716525] read_itxbf: More MBSS[1] ITxBfEn = 1 [ 36.721138] read_itxbf: More BSSID[2] [ 36.724820] read_itxbf: More MBSS[2] ITxBfEn = 1 [ 36.729434] read_itxbf: More BSSID[3] [ 36.733090] read_itxbf: More MBSS[3] ITxBfEn = 1 [ 36.737725] read_itxbf: More BSSID[4] [ 36.741384] read_itxbf: More MBSS[4] ITxBfEn = 1 [ 36.746021] read_itxbf: More BSSID[5] [ 36.749680] read_itxbf: More MBSS[5] ITxBfEn = 1 [ 36.754310] read_itxbf: More BSSID[6] [ 36.757969] read_itxbf: More MBSS[6] ITxBfEn = 1 [ 36.762579] read_itxbf: More BSSID[7] [ 36.766262] read_itxbf: More MBSS[7] ITxBfEn = 1 [ 36.770876] read_itxbf: Common.ITxBfEn = 1 [ 36.775095] read_etxbf: ETxBfEnCond = 1 [ 36.778928] read_etxbf: BSSID[0] [ 36.782150] read_etxbf: MBSS[0] ETxBfEnCond = 1 [ 36.786701] read_etxbf: More BSSID[1] [ 36.790362] read_etxbf: More MBSS[1] ETxBfEnCond = 1 [ 36.795351] read_etxbf: More BSSID[2] [ 36.799010] read_etxbf: More MBSS[2] ETxBfEnCond = 1 [ 36.803989] read_etxbf: More BSSID[3] [ 36.807649] read_etxbf: More MBSS[3] ETxBfEnCond = 1 [ 36.812606] read_etxbf: More BSSID[4] [ 36.816287] read_etxbf: More MBSS[4] ETxBfEnCond = 1 [ 36.821248] read_etxbf: More BSSID[5] [ 36.824930] read_etxbf: More MBSS[5] ETxBfEnCond = 1 [ 36.829891] read_etxbf: More BSSID[6] [ 36.833569] read_etxbf: More MBSS[6] ETxBfEnCond = 1 [ 36.838531] read_etxbf: More BSSID[7] [ 36.842187] read_etxbf: More MBSS[7] ETxBfEnCond = 1 [ 36.847878] [RTMPSetProfileParameters]Disable DFS/Zero wait=0/0 [ 36.885509] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [ 36.891240] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [ 36.896986] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [ 36.914845] HT: WDEV[0] Ext Channel = ABOVE [ 36.919298] HT: greenap_cap = 0 [ 36.953774] tx_pwr_comp_init():NotSupportYet! [ 36.958359] MtCmdSetMacTxRx:(ret = 0) [ 36.962141] asic_bss_beacon_init(): NotSupportedFunc for this arch(HIF_MT)! [ 36.969157] AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)! [ 36.975745] MtAsicSetRalinkBurstMode(2221): Not support for HIF_MT yet! [ 36.982423] MtAsicSetPiggyBack(592): Not support for HIF_MT yet! [ 36.988534] WifiFwdSet::disabled=0 [ 36.991971] AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)! [ 36.998445] Main bssid = 00:00:00:00:00:00 [ 37.002603] AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)! [ 37.009277] MtCmdSetMacTxRx:(ret = 0) [ 37.013045] AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)! [ 37.019741] MtCmdSetMacTxRx:(ret = 0) [ 37.023449] INIT REDUCE TCP ACK, rai0 [ 37.027133] <==== mt_wifi_init, Status=0 [ 37.031053] TxBfModuleEnCtrl:It's not DBDC mode [ 37.035676] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 [ 37.053631] MSTA_Init (1) ---> ApCli [ 37.057516] Register MSTA IF (apclii0) , pAd->MSTANum = 1 [ 37.064118] Caller: SetCommonHT+0xc4/0x130 [mt7663] [ 37.069165] [ 37.069165] phy_mode=49, ch=149, wdev_type=2 [ 37.074999] ht_cap: ht_cap->HtCapInfo, [ 37.078875] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0 [ 37.086604] ht_cap: ht_cap->HtCapParm, [ 37.090472] mdpu_density=0, ampdu_factor=3 [ 37.096296] WtcSetMaxStaNum: MaxStaNum:100, BssidNum:8, WdsNum:0, ApcliNum:1, MaxNumChipRept:24, MinMcastWcid:126 [ 38.037604] RedInit: set Driver/N9 RED Enable to 1. [ 38.042525] RedInit: RED Initiailize Done. [ 38.046705] cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2. [ 38.052975] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 38.059266] wifi_sys_open(), wdev idx = 0 [ 38.063283] wdev_attr_update(): wdevId0 = e0:e1:a9:6f:65:56 [ 38.068930] [BuildChannelList] BandIdx = 0, PhyMode = 49, ChListNum = 13: [ 38.075845] [RadarStateCheck] RD_NORMAL_MODE [ 38.081317] AsicSwitchChannel(): 5G Channel:155, then must be Channel_Band:1 !! [ 38.137177] Caller: wlan_operate_init+0xf8/0x10c [mt7663] [ 38.142592] [ 38.142592] phy_mode=49, ch=149, wdev_type=1 [ 38.148557] ht_cap: ht_cap->HtCapInfo, [ 38.152397] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0 [ 38.160065] ht_cap: ht_cap->HtCapParm, [ 38.163919] mdpu_density=4, ampdu_factor=3 [ 38.168352] AP inf up for ra_0(func_idx) OmacIdx=0 [ 38.173175] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 38.178577] ApAutoChannelAtBootUp-----------------> [ 38.183456] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 0 [ 38.189071] ApAutoChannelAtBootUp<----------------- [ 38.193981] ap_run_at_boot() : ACS is disable !! [ 38.199438] [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 38.206287] Caller: SetCommonHT+0xc4/0x130 [mt7663] [ 38.211172] [ 38.211172] phy_mode=49, ch=149, wdev_type=1 [ 38.216966] ht_cap: ht_cap->HtCapInfo, [ 38.220806] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0 [ 38.228480] ht_cap: ht_cap->HtCapParm, [ 38.232315] mdpu_density=4, ampdu_factor=3 [ 38.236498] wifi_sys_linkup(), wdev idx = 0 [ 38.240692] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:135 for WDEV_TYPE:1 [ 38.240692] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 38.253852] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8192 [ 38.275053] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 [ 38.280841] MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0 [ 38.286790] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 [ 38.292807] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0 [ 38.299443] AsicSetTxStream(): NotSupportedFunc for this arch(HIF_MT)! [ 38.305993] AsicSetRxStream(): NotSupportedFunc for this arch(HIF_MT)! [ 38.321054] apidx 0 for WscUUIDInit [ 38.324592] Generate UUID for apidx(0) [ 38.375430] device rai0 entered promiscuous mode [ 38.380157] br-lan: port 2(rai0) entered forwarding state [ 38.385617] br-lan: port 2(rai0) entered forwarding state [ 40.383568] br-lan: port 2(rai0) entered forwarding state


OpenWrt bootlog

Trying to boot from NOR U-Boot 2018.09-gbef8015-dirty (Dec 09 2020 - 06:28:07 -0500) CPU: MediaTek MT7621AT ver 1, eco 3 Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz Model: MediaTek MT7621 reference board DRAM: 128 MiB Loading Environment from SPI Flash... SF: Detected w25q128bv with page size 256 Bytes, erase size 64 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: uartlite0@1e000c00 Out: uartlite0@1e000c00 Err: uartlite0@1e000c00 Net: Warning: eth@1e100000 (eth0) using random MAC address - 5e:69:c8:f8:cf:5b eth0: eth@1e100000 Hit any key to stop autoboot: 0 Using eth@1e100000 device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 Filename 'firmware_auto.bin'. Load address: 0x80010000 Loading: * ARP Retry count exceeded; starting again *** TFTP client failure: -110 *** *** Operation Aborted! *** *** U-Boot Boot Menu *** 1. Startup system (Default) 2. Upgrade firmware 3. Upgrade bootloader 4. Upgrade bootloader (advanced mode) 5. Load image 0. U-Boot console Press UP/DOWN to move, ENTER to select ## Booting kernel from Legacy Image at bfc50000 ... Image Name: MIPS OpenWrt Linux-5.15.127 Image Type: MIPS Linux Kernel Image (uncompressed) Data Size: 2846981 Bytes = 2.7 MiB Load Address: 80001000 Entry Point: 80001000 Verifying Checksum ... OK Loading Kernel Image ... OK OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.15.127 (adfilimonov@debian) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23784-c2bc4c4950) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Aug 21 18:41:02 2023 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is COMFAST CF-EW72 V2 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s14512 r8192 d22352 u45056 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00052a60 [ 0.000000] Readback ErrCtl register=00052a60 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119052K/131072K available (6982K kernel code, 626K rwdata, 1432K rodata, 1252K init, 217K bss, 12020K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008027] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.066211] pid_max: default: 32768 minimum: 301 [ 0.071599] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.078811] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.090362] rcu: Hierarchical SRCU implementation. [ 0.095850] smp: Bringing up secondary CPUs ... [ 0.101297] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.101323] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.101338] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.101382] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.160622] Synchronize counters for CPU 1: done. [ 0.193121] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.193141] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.193153] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.193178] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.252093] Synchronize counters for CPU 2: done. [ 0.282765] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.282787] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.282798] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.282828] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.337279] Synchronize counters for CPU 3: done. [ 0.367140] smp: Brought up 1 node, 4 CPUs [ 0.375938] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.385736] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.392816] pinctrl core: initialized pinctrl subsystem [ 0.399476] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.408685] rt2880-pinmux pinctrl: there is not valid maps for state default [ 0.436463] clocksource: Switched to clocksource GIC [ 0.442776] NET: Registered PF_INET protocol family [ 0.447791] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.455659] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.463957] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.471639] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.479256] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.486220] TCP: Hash tables configured (established 1024 bind 1024) [ 0.492691] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.499183] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.506398] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.512080] PCI: CLS 0 bytes, default 32 [ 0.518022] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.530026] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.535788] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.549918] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.555855] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.561826] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.567945] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 0.574611] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 0.583379] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000 [ 0.591487] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 0.956479] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 0.961295] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 0.966154] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 0.973396] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 0.979685] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.985091] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 0.991946] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.998170] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.004098] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.010339] pci 0000:00:00.0: reg 0x14: [mem 0x60500000-0x6050ffff] [ 1.016622] pci 0000:00:00.0: supports D1 [ 1.020538] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.027019] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x0d8000 [ 1.033001] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x01ffffff] [ 1.039254] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.045488] pci 0000:00:01.0: supports D1 [ 1.049424] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.056875] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.065058] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 [ 1.071045] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 1.077434] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.084703] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.089899] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.095898] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.102661] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.109836] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.116650] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280 [ 1.122599] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.129782] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.136952] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.144192] pci 0000:02:00.0: supports D1 D2 [ 1.148388] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.154966] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.170993] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.176147] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.182259] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.188981] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.196125] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.202781] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.209325] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.216213] pci 0000:00:01.0: BAR 0: assigned [mem 0x60000000-0x61ffffff] [ 1.222985] pci 0000:00:00.0: BAR 8: assigned [mem 0x62000000-0x620fffff] [ 1.229721] pci 0000:00:00.0: BAR 9: assigned [mem 0x62100000-0x621fffff pref] [ 1.236891] pci 0000:00:01.0: BAR 8: assigned [mem 0x62200000-0x622fffff] [ 1.243600] pci 0000:00:01.0: BAR 9: assigned [mem 0x62300000-0x624fffff pref] [ 1.250801] pci 0000:00:00.0: BAR 1: assigned [mem 0x62500000-0x6250ffff] [ 1.257556] pci 0000:00:01.0: BAR 1: assigned [mem 0x62510000-0x6251ffff] [ 1.264250] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff] [ 1.270327] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.276352] pci 0000:01:00.0: BAR 0: assigned [mem 0x62000000-0x620fffff] [ 1.283118] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.288046] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.294057] pci 0000:00:00.0: bridge window [mem 0x62000000-0x620fffff] [ 1.300825] pci 0000:00:00.0: bridge window [mem 0x62100000-0x621fffff pref] [ 1.308006] pci 0000:02:00.0: BAR 0: assigned [mem 0x62300000-0x623fffff 64bit pref] [ 1.315669] pci 0000:02:00.0: BAR 2: assigned [mem 0x62400000-0x62403fff 64bit pref] [ 1.323403] pci 0000:02:00.0: BAR 4: assigned [mem 0x62404000-0x62404fff 64bit pref] [ 1.331085] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.335969] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 1.342046] pci 0000:00:01.0: bridge window [mem 0x62200000-0x622fffff] [ 1.348784] pci 0000:00:01.0: bridge window [mem 0x62300000-0x624fffff pref] [ 1.356967] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 1.364645] printk: console [ttyS0] disabled [ 1.369081] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 1.378136] printk: console [ttyS0] enabled [ 1.378136] printk: console [ttyS0] enabled [ 1.386384] printk: bootconsole [early0] disabled [ 1.386384] printk: bootconsole [early0] disabled [ 1.398957] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 1.405527] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.410492] 4 fixed-partitions partitions found on MTD device spi0.0 [ 1.416890] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions [ 1.424212] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions [ 1.431820] Creating 4 MTD partitions on "spi0.0": [ 1.436642] 0x000000000000-0x000000030000 : "Bootloader" [ 1.443024] 0x000000030000-0x000000040000 : "Config" [ 1.448981] 0x000000040000-0x000000050000 : "factory" [ 1.455226] OF: Bad cell count for /palmbus@1e000000/spi@b00/flash@0/partitions [ 1.462890] 0x000000050000-0x000001000000 : "firmware" [ 1.469328] 2 uimage-fw partitions found on MTD device firmware [ 1.475264] Creating 2 MTD partitions on "firmware": [ 1.480252] 0x000000000000-0x0000002b7145 : "kernel" [ 1.485202] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 1.494471] 0x0000002b7145-0x000000fb0000 : "rootfs" [ 1.499484] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.509602] mtd: setting mtd5 (rootfs) as root device [ 1.514803] 1 squashfs-split partitions found on MTD device rootfs [ 1.521004] 0x0000006a0000-0x000000fb0000 : "rootfs_data" [ 1.659408] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.671559] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 1.681382] i2c_dev: i2c /dev entries driver [ 1.688673] NET: Registered PF_INET6 protocol family [ 1.695785] Segment Routing with IPv6 [ 1.699574] In-situ OAM (IOAM) with IPv6 [ 1.703577] NET: Registered PF_PACKET protocol family [ 1.709044] 8021q: 802.1Q VLAN Support v1.8 [ 1.719275] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module [ 1.742638] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode [ 1.750306] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 1.751272] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=23) [ 1.771017] mt7530-mdio mdio-bus:1f lan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=24) [ 1.784152] DSA: tree 0 setup [ 1.800024] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.811201] Freeing unused kernel image (initmem) memory: 1252K [ 1.817181] This architecture does not have kernel memory protection. [ 1.823612] Run /sbin/init as init process [ 2.565639] init: Console is alive [ 2.569604] init: - watchdog - [ 3.677325] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.758602] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.775721] init: - preinit - [ 5.033997] random: jshn: uninitialized urandom read (4 bytes read) [ 5.179357] random: jshn: uninitialized urandom read (4 bytes read) [ 5.214182] random: jshn: uninitialized urandom read (4 bytes read) [ 5.469807] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 5.482265] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 5.486897] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode [ 5.498212] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.789642] jffs2: notice: (361) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found. [ 7.808028] mount_root: switching to jffs2 overlay [ 7.823899] overlayfs: upper fs does not support tmpfile. [ 7.840697] urandom-seed: Seeding with /etc/urandom.seed [ 7.989248] procd: - early - [ 7.992370] procd: - watchdog - [ 8.610509] procd: - watchdog - [ 8.614290] procd: - ubus - [ 8.708724] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.717476] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.732688] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.745138] procd: - init - Please press Enter to activate this console. [ 9.456661] kmodloader: loading kernel modules from /etc/modules.d/* [ 9.719842] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b [ 9.727396] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36 [ 9.975144] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 9.980908] mt7603e 0000:01:00.0: enabling device (0000 -> 0002) [ 9.987252] mt7603e 0000:01:00.0: ASIC revision: 76030010 [ 10.641110] urngd: v1.0.2 started. [ 11.018562] mt7603e 0000:01:00.0: Firmware Version: ap_pcie [ 11.024163] mt7603e 0000:01:00.0: Build Time: 20160107100755 [ 11.051407] mt7603e 0000:01:00.0: firmware init done [ 11.249945] pci 0000:00:01.0: enabling device (0000 -> 0003) [ 11.255644] mt7615e 0000:02:00.0: enabling device (0000 -> 0002) [ 11.365287] PPP generic driver version 2.4.2 [ 11.373473] NET: Registered PF_PPPOX protocol family [ 11.392478] kmodloader: done loading kernel modules from /etc/modules.d/* [ 11.419024] random: crng init done [ 11.422454] random: 30 urandom warning(s) missed due to ratelimiting [ 13.341230] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin [ 20.603809] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 20.625845] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 20.634355] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 20.638016] mt7530-mdio mdio-bus:1f lan: configuring for phy/gmii link mode [ 20.650644] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 20.659397] br-lan: port 1(lan) entered blocking state [ 20.664600] br-lan: port 1(lan) entered disabled state [ 20.672223] device lan entered promiscuous mode [ 20.676897] device eth0 entered promiscuous mode [ 20.719441] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode [ 21.929202] br-lan: port 2(phy1-ap0) entered blocking state [ 21.934870] br-lan: port 2(phy1-ap0) entered disabled state [ 21.941150] device phy1-ap0 entered promiscuous mode [ 23.257470] mt7530-mdio mdio-bus:1f lan: Link is Up - 1Gbps/Full - flow control rx/tx


Notes

Space for additional notes, links to forum threads or other resources.

  • ...

Tags

FIXME Add tags below, then remove this fixme.

How to add tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/05/20 18:28
  • by dnd