COMFAST CF-E560AC

U-Boot 1.1.4-g9e952007-dirty (Dec 20 2015 - 08:47:17)

ap143 - Honey Bee 2.0

DRAM: 128 MB Flash: 16 MB

eth0 link down FAIL eth1 link down FAIL Using eth0 device Tx Timed out ping failed; host 192.168.1.10 is not alive Unknown command 'ERROR!' - try 'help' Hit any key to stop autoboot: 0 ## Booting image at 9f020000 ...

 Image Name:   MIPS OpenWrt Linux-3.10.44
 Created:      2017-12-16   6:02:44 UTC
 Image Type:   MIPS Linux Kernel Image (lzma compressed)
 Data Size:    1124064 Bytes =  1.1 MB
 Load Address: 80060000
 Entry Point:  80060000
 Verifying Checksum at 0x9f020040 ...OK
 Uncompressing Kernel Image ... OK

No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 134217728

Starting kernel ...

[ 0.000000] Linux version 3.10.44 (root@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unk nown) ) #1 Sat Dec 16 14:01:59 CST 2017 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 ver 2 rev 0 [ 0.000000] Clocks: CPU:650.000MHz, DDR:391.870MHz, AHB:216.666MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=COMFAST-CF-E560AC console=ttyS0,115200 mtdparts=spi0.0:64k(u-b oot)ro,64k(art)ro,1536k(kernel),14592k(rootfs),64k(configs),64k(nvram)ro,16128k@0x20000(firmware) rootfst ype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125796k/131072k available (2425k kernel code, 5276k reserved, 689k data, 276k init , 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.050000] Mount-cache hash table entries: 512 [ 0.060000] NET: Registered protocol family 16 [ 0.070000] MIPS: machine is COMFAST CF-E560AC [ 0.510000] registering PCI controller with io_map_base unset [ 0.530000] bio: create slab <bio-0> at 0 [ 0.540000] PCI host bridge to bus 0000:00 [ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.560000] pci 0000:00:00.0: invalid calibration data [ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.570000] Switching to clocksource MIPS [ 0.580000] NET: Registered protocol family 2 [ 0.580000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.590000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.600000] TCP: reno registered [ 0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] NET: Registered protocol family 1 [ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.640000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.650000] msgmni has been set to 245 [ 0.660000] io scheduler noop registered [ 0.660000] io scheduler deadline registered (default) [ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.700000] console [ttyS0] enabled, bootconsole disabled [ 0.700000] console [ttyS0] enabled, bootconsole disabled [ 0.710000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.720000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.730000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.730000] 7 cmdlinepart partitions found on MTD device spi0.0 [ 0.740000] Creating 7 MTD partitions on “spi0.0”: [ 0.740000] 0x000000000000-0x000000010000 : “u-boot” [ 0.750000] 0x000000010000-0x000000020000 : “art” [ 0.760000] 0x000000020000-0x0000001a0000 : “kernel” [ 0.770000] 0x0000001a0000-0x000000fe0000 : “rootfs” [ 0.770000] mtd: device 3 (rootfs) set to be root filesystem [ 0.780000] 1 squashfs-split partitions found on MTD device rootfs [ 0.790000] 0x0000007c0000-0x000000fe0000 : “rootfs_data” [ 0.790000] 0x000000fe0000-0x000000ff0000 : “configs” [ 0.800000] 0x000000ff0000-0x000001000000 : “nvram” [ 0.810000] 0x000000020000-0x000000fe0000 : “firmware” [ 0.840000] libphy: ag71xx_mdio: probed [ 0.840000] eth0: Atheros AG71xx at 0xba000000, irq 5 [ 1.400000] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.440000] eth1: Atheros AG71xx at 0xb9000000, irq 4 [ 2.000000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.010000] TCP: cubic registered [ 2.010000] NET: Registered protocol family 17 [ 2.020000] Bridge firewalling registered [ 2.020000] 8021q: 802.1Q VLAN Support v1.8 [ 2.030000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.040000] Freeing unused kernel memory: 276K (8036b000 - 803b0000) [ 3.010000] init: Console is alive [ 3.010000] init: - watchdog - [ 5.010000] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.260000] jffs2: notice: (378) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found. [ 8.280000] mount_root: switching to jffs2 overlay [ 8.340000] procd: - early - [ 8.340000] procd: - watchdog - [ 8.960000] procd: - ubus - [ 9.990000] procd: - init - Please press Enter to activate this console. [ 11.840000] natsemi dp8381x driver, version 2.1, Sept 11, 2006 [ 11.840000] originally by Donald Becker becker@scyld.com [ 11.840000] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder [ 11.880000] gre: GRE over IPv4 demultiplexor driver [ 11.890000] ip_gre: GRE over IPv4 tunneling driver [ 11.910000] i2c /dev entries driver [ 11.910000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 11.920000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 12.150000] PCI: Enabling device 0000:00:00.0 (0000 → 0002) [ 12.150000] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 13.080000] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 [ 13.090000] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1 [ 13.120000] ath10k_pci 0000:00:00.0: firmware ver 10.4-3.5.1-00014 api 5 features no-p2p,mfp,peer-flow -ctrl,allows-mesh-bcast crc32 983b7b7a [ 13.420000] ath10k_pci 0000:00:00.0: board_file api 2 bmi_id 0:0 crc32 9310e54f [ 15.220000] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal otp max-sta 512 raw 0 hwcrypto 1 [ 15.370000] u32 classifier [ 15.370000] input device check on [ 15.370000] Actions configured [ 15.390000] Mirror/redirect action on [ 15.420000] nf_conntrack version 0.5.0 (1969 buckets, 7876 max) [ 15.500000] Ebtables v2.0 registered [ 15.510000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.570000] Netfilter messages via NETLINK v0.30. [ 15.630000] xt_time: kernel timezone is -0000 [ 15.650000] ctnetlink v0.93: registering with nfnetlink. [ 15.670000] PPP generic driver version 2.4.2 [ 15.680000] PPP MPPE Compression module registered [ 15.690000] NET: Registered protocol family 24 [ 15.740000] ieee80211 phy1: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 [ 25.840000] device eth0 entered promiscuous mode [ 25.870000] device eth1 entered promiscuous mode [ 25.880000] br-lan: port 2(eth1) entered forwarding state [ 25.890000] br-lan: port 2(eth1) entered forwarding state [ 26.840000] br-lan: port 2(eth1) entered disabled state [ 30.210000] device wlan8 entered promiscuous mode [ 33.400000] device wlan0 entered promiscuous mode [ 37.500000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 39.240000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 40.660000] br-lan: port 3(wlan8) entered forwarding state [ 40.660000] br-lan: port 3(wlan8) entered forwarding state [ 41.430000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 42.220000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 42.660000] br-lan: port 3(wlan8) entered forwarding state

[ 0.000000] Linux version 4.19.98 (gus@uki) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12127-34e0065feb)) #0 Mon Feb 3 04:12:18 2020 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is COMFAST CF-E560AC [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 122428K/131072K available (4285K kernel code, 178K rwdata, 1012K rodata, 1236K init, 206K bss, 8644K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] CPU clock: 650.000 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008271] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.074882] pid_max: default: 32768 minimum: 301 [ 0.080020] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.086996] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100146] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.110599] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.117219] pinctrl core: initialized pinctrl subsystem [ 0.124008] NET: Registered protocol family 16 [ 0.137232] PCI host bridge /ahb/pcie-controller@180c0000 ranges: [ 0.143759] MEM 0x0000000010000000..0x0000000013ffffff [ 0.149257] IO 0x0000000000000000..0x0000000000000000 [ 0.182662] PCI host bridge to bus 0000:00 [ 0.187096] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.194337] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.200214] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.207366] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.215761] pci 0000:00:00.0: [168c:0056] type 00 class 0x028000 [ 0.215830] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.215964] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.217117] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.217153] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.229639] clocksource: Switched to clocksource MIPS [ 0.236583] NET: Registered protocol family 2 [ 0.242239] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes) [ 0.250482] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.257843] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.264586] TCP: Hash tables configured (established 1024 bind 1024) [ 0.271487] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.277669] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.284837] NET: Registered protocol family 1 [ 0.289491] PCI: CLS 0 bytes, default 32 [ 0.294102] Crashlog allocated RAM at address 0x3f00000 [ 0.301623] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.316685] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.322911] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.350618] io scheduler noop registered [ 0.354760] io scheduler deadline registered (default) [ 0.361344] ar7200-usb-phy 18030000.usb-phy: phy reset is missing [ 0.370141] pinctrl-single 1804002c.pinmux: 576 pins, size 72 [ 0.377471] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.385158] console [ttyS0] disabled [ 0.388967] 18020000.uart: ttyS0 at MMIO 0x18020000 (irq = 9, base_baud = 1562500) is a 16550A [ 0.398151] console [ttyS0] enabled [ 0.405718] bootconsole [early0] disabled [ 0.433144] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.438083] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.444692] Creating 5 MTD partitions on “spi0.0”: [ 0.449691] 0x000000000000-0x000000010000 : “u-boot” [ 0.455915] 0x000000010000-0x000000020000 : “art” [ 0.461953] 0x000000020000-0x000000fe0000 : “firmware” [ 0.471335] 2 uimage-fw partitions found on MTD device firmware [ 0.477466] Creating 2 MTD partitions on “firmware”: [ 0.482683] 0x000000000000-0x0000001c0000 : “kernel” [ 0.488805] 0x0000001c0000-0x000000fc0000 : “rootfs” [ 0.494953] mtd: device 4 (rootfs) set to be root filesystem [ 0.502929] 1 squashfs-split partitions found on MTD device rootfs [ 0.509347] 0x000000400000-0x000000fc0000 : “rootfs_data” [ 0.516075] 0x000000fe0000-0x000000ff0000 : “configs” [ 0.522382] 0x000000ff0000-0x000001000000 : “nvram” [ 0.529935] libphy: Fixed MDIO Bus: probed [ 0.890755] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [ 1.570110] libphy: ag71xx_mdio: probed [ 1.575675] libphy: ar8xxx-mdio: probed [ 1.589407] switch0: Atheros AR8229 rev. 1 switch registered on mdio-bus.0 [ 1.641645] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.651784] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii [ 1.658527] ath79-wdt 18060008.wdt: unable to register misc device, err=-16 [ 1.665869] ath79-wdt: probe of 18060008.wdt failed with error -16 [ 1.675133] NET: Registered protocol family 10 [ 1.687011] Segment Routing with IPv6 [ 1.691020] NET: Registered protocol family 17 [ 1.695715] 8021q: 802.1Q VLAN Support v1.8 [ 2.041793] ag71xx 19000000.eth: connected to PHY at mdio-bus.0:1f:04 [uid=004dd042, driver=Generic PHY] [ 2.052842] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii [ 2.070065] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 2.087545] Freeing unused kernel memory: 1236K [ 2.092277] This architecture does not have kernel memory protection. [ 2.098926] Run /sbin/init as init process [ 2.519658] random: fast init done [ 3.244124] init: Console is alive [ 3.247998] init: - watchdog - [ 4.786425] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.975764] usbcore: registered new interface driver usbfs [ 4.981665] usbcore: registered new interface driver hub [ 4.987282] usbcore: registered new device driver usb [ 5.001942] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.020681] SCSI subsystem initialized [ 5.031805] ehci-platform: EHCI generic platform driver [ 5.037566] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.043551] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.051826] ehci-platform 1b000000.usb: irq 3, io mem 0x1b000000 [ 5.079672] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.087184] hub 1-0:1.0: USB hub found [ 5.091762] hub 1-0:1.0: 1 port detected [ 5.101995] usbcore: registered new interface driver usb-storage [ 5.111624] usbcore: registered new interface driver uas [ 5.117988] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.136188] init: - preinit - [ 6.125504] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 6.401845] random: procd: uninitialized urandom read (4 bytes read) [ 6.412732] usb-storage 1-1:1.0: USB Mass Storage device detected [ 6.430440] scsi host0: usb-storage 1-1:1.0 [ 6.622916] random: jshn: uninitialized urandom read (4 bytes read) [ 6.727652] random: jshn: uninitialized urandom read (4 bytes read) [ 7.484330] scsi 0:0:0:0: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 4 [ 7.716687] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.722980] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready [ 8.608792] sd 0:0:0:0: [sda] 249737216 512-byte logical blocks: (128 GB/119 GiB) [ 8.617266] sd 0:0:0:0: [sda] Write Protect is off [ 8.622294] sd 0:0:0:0: [sda] Mode Sense: 2f 00 00 00 [ 8.623015] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.640135] sda: sda1 sda2 [ 8.647645] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 8.750892] eth0: link up (1000Mbps/Full duplex) [ 8.757937] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 8.765003] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 12.050771] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 12.058293] jffs2_build_filesystem(): unlocking the mtd device... [ 12.058323] done. [ 12.066721] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 53.476347] done. [ 53.486149] jffs2: notice: (536) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 53.503955] mount_root: overlay filesystem has not been fully initialized yet [ 53.525212] mount_root: switching to jffs2 overlay [ 53.566142] overlayfs: upper fs does not support tmpfile. [ 54.066151] urandom-seed: Seed file not found (/etc/urandom.seed) [ 54.184498] eth0: link down [ 54.213333] procd: - early - [ 54.216460] procd: - watchdog - [ 54.865870] procd: - watchdog - [ 54.869596] procd: - ubus - [ 54.960091] urandom_read: 5 callbacks suppressed [ 54.960101] random: ubusd: uninitialized urandom read (4 bytes read) [ 54.972263] random: ubusd: uninitialized urandom read (4 bytes read) [ 54.980535] procd: - init - [ 55.837684] kmodloader: loading kernel modules from /etc/modules.d/* [ 55.891270] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 55.899102] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 55.958297] usbcore: registered new interface driver ums-alauda [ 55.981339] usbcore: registered new interface driver ums-cypress [ 56.001513] usbcore: registered new interface driver ums-datafab [ 56.010746] usbcore: registered new interface driver ums-freecom [ 56.031517] usbcore: registered new interface driver ums-isd200 [ 56.051482] usbcore: registered new interface driver ums-jumpshot [ 56.071389] usbcore: registered new interface driver ums-karma [ 56.081039] usbcore: registered new interface driver ums-sddr09 [ 56.098926] usbcore: registered new interface driver ums-sddr55 [ 56.121802] usbcore: registered new interface driver ums-usbat [ 56.161221] xt_time: kernel timezone is -0000 [ 56.383677] PPP generic driver version 2.4.2 [ 56.398462] urngd: v1.0.2 started. [ 56.403646] NET: Registered protocol family 24 [ 56.556529] ath: EEPROM regdomain: 0x0 [ 56.556541] ath: EEPROM indicates default country code should be used [ 56.556544] ath: doing EEPROM country→regdmn map search [ 56.556561] ath: country maps to regdmn code: 0x3a [ 56.556567] ath: Country alpha2 being used: US [ 56.556570] ath: Regpair used: 0x3a [ 56.571455] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 56.573485] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=13 [ 56.680215] kmodloader: done loading kernel modules from /etc/modules.d/* [ 56.891195] random: crng init done [ 69.753879] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 69.761291] eth0: link up (1000Mbps/Full duplex) [ 69.766101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 69.799278] br-lan: port 1(eth0.1) entered blocking state [ 69.804958] br-lan: port 1(eth0.1) entered disabled state [ 69.811021] device eth0.1 entered promiscuous mode [ 69.815978] device eth0 entered promiscuous mode [ 69.851595] br-lan: port 1(eth0.1) entered blocking state [ 69.857192] br-lan: port 1(eth0.1) entered forwarding state [ 69.863283] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 69.959393] br-lan: port 2(eth1) entered blocking state [ 69.964911] br-lan: port 2(eth1) entered disabled state [ 69.970757] device eth1 entered promiscuous mode [ 70.750367] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 72.770761] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 72.798752] br-lan: port 3(wlan0) entered blocking state [ 72.804478] br-lan: port 3(wlan0) entered disabled state [ 72.810540] device wlan0 entered promiscuous mode [ 73.072571] eth1: link up (100Mbps/Full duplex) [ 73.077329] br-lan: port 2(eth1) entered blocking state [ 73.082802] br-lan: port 2(eth1) entered forwarding state [ 79.992135] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 79.999024] br-lan: port 3(wlan0) entered blocking state [ 80.004628] br-lan: port 3(wlan0) entered forwarding state