User Tools

Site Tools


toh:buffalo:whr-g300nv1

Buffalo WHR-G300N V1

Sometimes labeled as “WHR-G300N-R”.

Supported Versions

Hardware Highlights

Installation

TFTP

When powered with the reset button held down, it attempts to download “firmware.ram” from a TFTP server at 192.168.11.2 and sets its IP to 192.168.11.1. Timeout is set to “10”. After a timeout, the router continues to boot linux. If the reset button continues to be held down, the device resets once the busybox “press enter for prompt” is displayed.

Hardware details

Serial

JP1 (unpopulated 4 pin connector), located near the “AOSS” button on the top of the case. Pin 1 is the pin with the square pad, towards the edge of the board with LEDs on it.

JP1
Pin 1 Pin 2 Pin 3 Pin 4
3.3V TX RX GND

JTAG

Yes, untested, needs pullups.

Bootlogs

OEM bootlog

U-Boot 1.1.3 for BUFFALO AIRSTATION (Aug 26 2008 - 13:08:44) Board: Ralink APSoC DRAM: 32 MB Top of RAM usable for U-Boot at: 82000000 Stack Pointer at: 81f4ff98 relocate_code Pointer at: 81fa0000 Now running in RAM - U-Boot at: 81fa0000 FLASH ID : 00h=[0xc2], 01h=[0x22a8], 0Eh=[0x0], 0Fh=[0x19] Set info->start[0]=BF000000 flash_protect ON: from 0xBF000000 to 0xBF02B84F protect on 0 protect on 1 protect on 2 protect on 3 protect on 4 protect on 5 protect on 6 protect on 7 protect on 8 protect on 9 flash_protect ON: from 0xBF030000 to 0xBF03FFFF protect on 10 flash_protect ON: from 0xBF040000 to 0xBF04FFFF protect on 11 uboot use 81F4FFB0 - 82000000 Memory Test start(80000000) end(81F00000) size(01F00000) Pattern 55555555 Writing... Reading... Pattern AAAAAAAA Writing... Reading... Pattern 00000000 Writing... Reading... Memory Test OK ### buf_ver=[1.09] U-Boot Ver.=[1.09] ### build_date(env)=[Aug 26 2008 - 13:08:44] build_date(bin)=[Aug 26 2008 - 13:08:44] ============================================ Ralink UBoot Version: 3.1 -------------------------------------------- ASIC 3052_MP2 (MAC to GigaMAC Mode) DRAM COMPONENT: 256Mbits DRAM BUS: 32BIT Total memory: 64 MBytes Date:Aug 26 2008 Time:13:08:44 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 384 MHZ #### SDRAM bus set to 32 bit SDRAM size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 9: Load Boot Loader code then write to Flash via TFTP.  0 Net: eth_register Eth0 (10/100-M) enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:19 00:AA:BB:CC:DD:19: eth_current->name = Eth0 (10/100-M) 6: System Load Linux Kernel then write to Flash via TFTP Server. netboot_common, argc= 2 *************buf = 0x81fcb9e0 **********NexTxPacket = 81fe3ac0 NetTxPacket = 0x81FE3AC0 NetRxPackets[0] = 0x81FE40C0 NetRxPackets[1] = 0x81FE46C0 NetRxPackets[2] = 0x81FE4CC0 NetRxPackets[3] = 0x81FE52C0 NetRxPackets[4] = 0x81FE58C0 NetRxPackets[5] = 0x81FE5EC0 NetRxPackets[6] = 0x81FE64C0 NetRxPackets[7] = 0x81FE6AC0 NetRxPackets[8] = 0x81FE70C0 NetRxPackets[9] = 0x81FE76C0 NetRxPackets[10] = 0x81FE7CC0 NetRxPackets[11] = 0x81FE82C0 NetRxPackets[12] = 0x81FE88C0 NetRxPackets[13] = 0x81FE8EC0 NetRxPackets[14] = 0x81FE94C0 NetRxPackets[15] = 0x81FE9AC0 NetRxPackets[16] = 0x81FEA0C0 NetRxPackets[17] = 0x81FEA6C0 NetRxPackets[18] = 0x81FEACC0 NetRxPackets[19] = 0x81FEB2C0 KSEG1ADDR(NetTxPacket) = 0xA1FE3AC0 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Mac to giga Mac mode rx_ring = A1FCBE00, tx_ring0 = A1FCBCC0 Header Payload scatter function is Disable !! RT2880_PDMA_GLO_CFG=00000020 ************************************************* RX_CALC_IDX0=19 RX_DRX_IDX0 = 0 ************************************************* ETH_STATE_ACTIVE!! tftp server(receive) go, waiting:4[sec] Trying Eth0 (10/100-M) ETH_STATE_ACTIVE!! Load address: 0x81000000 TftpServer Timeout; Trying Eth0 (10/100-M) ETH_STATE_ACTIVE!! no file was loaded. netboot_common, argc= 3 KSEG1ADDR(NetTxPacket) = 0xA1FE3AC0 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) ETH_STATE_ACTIVE!! Using Eth0 (10/100-M) device TFTP from server 192.168.11.2; our IP address is 192.168.11.1 Filename 'firmware.ram'. TIMEOUT_COUNT=10,Load address: 0x81000000 Loading: *T T T T Retry count exceeded; starting again 3: System Boot system code via Flash. ## Booting image at bf050000 ... Image Name: Linux Kernel Image Created: 2010-02-08 10:05:05 UTC System Control Status = 0x20440000 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 895660 Bytes = 874.7 kB Load Address: 80000000 Entry Point: 8029b000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8029b000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (vc03021@mkitec-xen) (gcc version 3.3.6) #1 Mon Feb 8 18:57:30 JST 2010 The CPU feqenuce set to 384 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = 800060, status = 1100ff00 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00177000(1536000) CPU frequency 384.00 MHz Using 192.000 MHz high precision timer. Console: colour dummy device 80x25 Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29456k/32768k available (2201k kernel code, 3312k reserved, 462k data, 116k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro io scheduler noop registered (default) FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB Ralink gpio driver initialized HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. mel_initsw initialized. ++ RALINK_REG_PIODATA = B0000620 Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 254 PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 physmap flash device: bfc00000 at 400000 RT2880 SOC Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Creating 6 MTD partitions on "RT2880 SOC Physically mapped flash": 0x00000000-0x00030000 : "uboot" 0x00030000-0x00040000 : "uboot_environ" 0x00040000-0x00050000 : "factory_default" 0x00050000-0x00140000 : "linux" 0x00140000-0x003f0000 : "rootfs" 0x003f0000-0x00400000 : "user_property" block2mtd: version $Revision: 1.1.1.1 $ u32 classifier nf_conntrack version 0.5.0 (256 buckets, 2048 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux ipt_time loading TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 116k freed Warning: unable to open an initial console. init started: BusyBox v1.00 (2010.02.08-09:59+0000) multi-call binary Please press Enter to activate this console. rc.c(324) VerifyParamsOfInit :x:create status sections insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko Load RT2880 Timer Module(Wdg/Soft) insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko rt2860v2_ap: module license 'unspecified' taints kernel. 2860 version : 1.9.0.0 (Feb 8 2010) === pAd = c0420000, size = 486264 === <-- RTMPAllocAdapterBlock, Status=0 RX DESC a1e06000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 1. Phy Mode = 0 2. Phy Mode = 0 3. Phy Mode = 0 MCS Set = 00 00 00 00 00 Main bssid = 00:1d:73:d1:09:98 The UUID Hex string is:2880288028801880a880001d73d10998 The UUID ASCII string is:28802880-2880-1880-a880-001d73d10998! <==== RTMPInitialize, Status=0 0x1300 = 00064220 wlctl-ral-tool.c(700) wl_ral_get_e2p :DEBUG:EEPROM [0x0038]:0x0000 wlctl-ral-tool.c(700) wl_ral_get_e2p :DEBUG:EEPROM [0x0036]:0x0426 ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! call WscStop[rt28xx_close/466] insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/raeth/raeth.ko GDMA1_MAC_ADRH -- : 0x00000000 GDMA1_MAC_ADRL -- : 0x00000000 Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated, mtu = 1600! GDMA1_MAC_ADRH -- : 0x00002c00 GDMA1_MAC_ADRL -- : 0x001d7311 PROC INIT OK! GDMA1_MAC_ADRH -- : 0x00000100 GDMA1_MAC_ADRL -- : 0x001d73d1 phy_tx_ring = 0x01db5000, tx_ring = 0xa1db5000, size: 16 bytes phy_rx_ring = 0x01db6000, rx_ring = 0xa1db6000, size: 16 bytes GDMA1_FWD_CFG = 10000 Operation not supported Operation not supported insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko insmod: cannot insert `/lib/modules/kernel/arch/mips/rt2880/rt_timer.ko': Invalid parameters (17): Invalid argument rcUtil.c(2307) Wireless_Insmod :####:insmod rt_timer : FAILED insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko insmod: cannot insert `/lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko': Invalid parameters (17): Invalid argument rcUtil.c(2316) Wireless_Insmod :####:insmod rt2860v2_ap : FAILED rcUtil.c(2494) Wireless_Rmmod :####:rmmod rt2860Unload RT2880 Timer Module(Wdg/Soft) v2_ap : SUCCESS rcUtil.c(2501) Wireless_Rmmod :####:rmmod rt_timer : SUCCESS insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko insmod: /lib/modules/2.6.21: No such file or directoryLoad RT2880 Timer Module(Wdg/Soft) Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko 2860 version : 1.9.0.0 (Feb 8 2010) === pAd = c0418000, size = 486264 === <-- RTMPAllocAdapterBlock, Status=0 RX DESC a1ee6000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 1. Phy Mode = 0 2. Phy Mode = 0 3. Phy Mode = 0 MCS Set = 00 00 00 00 00 Main bssid = 00:1d:73:d1:09:98 The UUID Hex string is:2880288028801880a880001d73d10998 The UUID ASCII string is:28802880-2880-1880-a880-001d73d10998! <==== RTMPInitialize, Status=0 0x1300 = 00064220 wlctl-ral-tool.c(700) wl_ral_get_e2p :DEBUG:EEPROM [0x0038]:0x0000 wlctl-ral-tool.c(700) wl_ral_get_e2p :DEBUG:EEPROM [0x0036]:0x0426 ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! ERROR!!! RTMPCancelTimer failed, Timer hasn't been initialize! call WscStop[rt28xx_close/466] insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/raeth/raeth.ko insmod: cannot insert `/lib/modules/kernel/drivers/net/raeth/raeth.ko': register_vlan_device: ALREADY had VLAN registered Invalid parameters (17): Invalid argument SIOCSregister_vlan_device: ALREADY had VLAN registered IFHWADDR: Device or resource busy vconfig: socket or ioctl error for add: Invalid argument vconfig: socket or ioctl error for add: Invalid argument Operation not supported Operation not supported insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko insmod: cannot insert `/lib/modules/kernel/arch/mips/rt2880/rt_timer.ko': Invalid parameters (17): Invalid argument rcUtil.c(2307) Wireless_Insmod :####:insmod rt_timer : FAILED insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko insmod: cannot insert `/lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko': Invalid parameters (17): Invalid argument rcUtil.c(2316) Wireless_Insmod :####:insmod rt2860v2_ap : FAILED rcUtil.c(2494) Wireless_Rmmod :####:rmmod rt2860Unload RT2880 Timer Module(Wdg/Soft) v2_ap : SUCCESS rcUtil.c(2501) Wireless_Rmmod :####:rmmod rt_timer : SUCCESS insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko insmod: cannot insert `/lib/modules/kernel/net/ipv4/netfilter/nf_conntrack_proto_gre.ko': Invalid parameters (17): Invalid argument insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko insmod: cannot insert `/lib/modules/kernel/net/ipv4/netfilter/nf_nat_proto_gre.ko': Invalid parameters (17): Invalid argument MidLayerModDep.c(798) startModules :INFO:Starting module init MidLayerModDep.c(810) startModules :INFO:Started module init 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_tz MidLayerModDep.c(810) startModules :INFO:Started module rc_tz 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_syslogd MidLayerModDep.c(810) startModules :INFO:Started module rc_syslogd 73[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_klogd MidLayerModDep.c(810) startModules :INFO:Started module rc_klogd 19[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_mode_check insmod: /liregister_vlan_device: ALREADY had VLAN registered b/modules/2.6.21: No such file or directory Usiregister_vlan_device: ALREADY had VLAN registered ng /lib/modules/kernel/drivers/net/raeth/raeth.ko insmod: cannot insert `/lib/modules/kernel/drivers/net/raeth/raeth.ko': Invalid parameters (17): Invalid argument SIOCSIFHWADDR: Device or resource busy vconfig: socket or ioctl error for add: Invalid argument vconfig: socket or ioctl error for add: Invalid argument MidLayerModDep.c(810) startModules :INFO:Started module rc_mode_check 1075[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_loif MidLayerModDep.c(810) startModules :INFO:Started module rc_loif 6[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_router_behavior MidLayerModDep.c(810) startModules :INFO:Started module rc_router_behavior 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module init MidLayerModDep.c(810) startModules :INFO:Started module init 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wiredlan MidLayerModDep.c(810) startModules :INFO:Started module rc_wiredlan 7[msec] MidLayerModDep.c(798) startModules :INFO:Starting module id No such device MidLayerModDep.c(810) startModules :INFO:Started module id 1009[msec] MidLayLoad RT2880 Timer Module(Wdg/Soft) erModDep.c(798) startModules :INFO:Starting module rc_lanif insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko 2860 version : 1.9.0.0 (Feb 8 2010) === pAd = c0418000, size = 486264 === <-- RTMPAllocAdapterBlock, Status=0 insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/buffalo/mcsnoop.ko mcsnoop: flush all snoop entry rc_lanif.c(370) StartOfrc_lanif :x:PPPoE Path throw? Algorithmics/MIPS FPU Emulator v1.5 mcsnoop_br_ioctl_device:229: mcast_maxage 75000 / 250 Cannot assign requested address MidLayerModDep.c(810) startModules :INFO:Started module rc_lanif 1250[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_udhcpd udhcpd (v0.9.9-pre) started max_leases value (256) not sane, setting to 64 instead MidLayerModDep.c(810) startModules :INFO:Started module rc_udhcpd 19[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_httpd MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,/bin/httpd MidLayerModDep.c(810) startModules :INFO:Started module rc_httpd 1020[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wireless_pre insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/arch/mips/rt2880/rt_timer.ko insmod: cannot insert `/lib/modules/kernel/arch/mips/rt2880/rt_timer.ko': Invalid parameters (17): Invalid argument rcUtil.c(2307) Wireless_Insmod :####:insmod rt_timer : FAILED insmod: /lib/modules/2.6.21: No such file or directory Using /lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko insmod: cannot insert `/lib/modules/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko': Invalid parameters (17): Invalid argument rcUtil.c(2316) Wireless_Insmod :####:insmod rt2860v2_ap : FAILED MidLayerModDep.c(810) startModules :INFO:Started module rc_wireless_pre 42[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wireless11bg wlctl-ram.c(1890) wlconf_up :DEBUG:before : 001D73D10998 wlctl-ram.c(1891) wlconf_up :DEBRX DESC a1989000 size = 2048 UG:after : 001D73D10998 wlctl-<-- RTMPAllocTxRxRingMemory, Status=0 ral-tool.c(308) wl_ral_setparam ERROR!!! :SET:SSID = 001DYour no. of SSIDs( = 1) does not match your BssidNum( = 4)! 73D10998 wlctl-ral-tool.c(308) wl_ral_setparam :SET:HideSSID = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:WirelessMode = 9 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BGProtection = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:HT_PROTECT = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:CountryRegion = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:HT_BW = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:HT_EXTCHA = 1 wlctl-ral-tool.c(308) wl_ral_setparam :SET:AutoChannelSelect = 1 wlctl-ral-tool.c(308) wl_ral_setparam :SET:Channel = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BasicRate = 15 wlctl-ral-tool.c(308) wl_ral_setparam :SET:WmmCapable = 1 wlctl-ral-tool.c(308) wl_ral_setparam :SET:TxBurst = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:APAifsn = 3;7;1;1 wlctl-ral-tool.c(308) wl_ral_setparam :SET:APCwmin = 4;4;3;2 wlctl-ral-tool.c(308) wl_ral_setparam :SET:APCwmax = 6;10;4;3 wlctl-ral-tool.c(308) wl_ral_setparam :SET:APTxop = 0;0;94;47 wlctl-ral-tool.c(308) wl_ral_setparam :SET:APACM = 0;0;0;0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BSSAifsn = 3;7;2;2 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BSSCwmin = 4;4;3;2 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BSSCwmax = 10;10;4;3 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BSSTxop = 0;0;94;47 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BSSACM = 0;0;0;0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:BuffaloCapability = 9 wlctl-ral-tool.c(308) wl_ral_setparam :SET:DtimPeriod = 1 wlctl-ral-tool.c(308) wl_ral_setparam :SET:NoForwarding = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:NoForwardingBTNBSSID = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:HT_RDG = 1 wlctl-ral-tool.c(327) wl_ral_setparam :NEW:NoDirectForwardBTNBSSID = 0 MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,iwevent wlctl-ral-tool.c(308) wl_ral_setparam :SET:AuthMode = WPAPSK wlctl-ral-tool.c(308) wl_ral_setparam :SET:WPAPSK = 41yh9yk1n9512 wlctl-ral-tool.c(308) wl_ral_setparam :SET:EncrypType = AES wlctl-ral-tool.c(308) wl_ral_setparam :SET:DefaultKeyID = 2 wlctl-ral-tool.c(308) wl_ral_setparam :SET:RekeyMethod = TIME wlctl-ral-tool.c(308) wl_ral_setparam :SET:RekeyInterval = 3600 wlctl-ral-tool.c(308) wl_ral_setparam :SET:TxPower = 100 wlctl-ral-tool.c(308) wl_ral_setparam :SET:WscConfMode = 0 wlctl-ral-tool.c(308) wl_ral_setparam :SET:WscConfStatus = 2 MidLayerModDep.c(810) startModules :INFO:Started module rc_wireless11bg 112[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wireless_post MidLayer.c(2793) ML_DoCommandVariableParamEx :x:## a_pCmd = ifconfig ra0 0.0.0.0 up ## BuffaloCapability(9) 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff ff 00 00 00 Waiting for Wireless Events from interfaces... Main bssid = 00:1d:73:d1:09:98 The UUID Hex string is:2880288028801880a880001d73d10998 The UUID ASCII string is:28802880-2880-1880-a880-001d73d10998! <==== RTMPInitialize, Status=0 0x1300 = 00064380 Warning: Driver for device ra0 has been compiled with version 22 of Wireless Extension, while this program supports up to version 20. Some things may be broken... 00:00:12.548714 ra0 Custom driver event:(RT2860) 00:00:00:00:00:00 disconnects with our wireless client MidLayer.c(2793) ML_DoCoERROR!!! mmandVariableParRTMPCancelTimer failed, Timer hasn't been initialize! amEx :x:## a_pCmERROR!!! d = brctl setporRTMPCancelTimer failed, Timer hasn't been initialize! tsep br0 ra0 offERROR!!! ## RTMPCancelTimer failed, Timer hasn't been initialize! MidLayerModDep.c(810) startModules :INFO:Started module rc_wireless_post 3027[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wireless11bg_mac_limit MidLayerModDep.c(810) startModules :INFO:Started module rc_wireless11bg_mac_limit 22[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_aoss_mssid MidLayerModDep.c(810) startModules :INFO:Started module rc_aoss_mssid 6[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_nas MidLayerModDep.c(810) startModules :INFO:Started module rc_nas 3[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_ap_serv server.c(249)start_ap_serv_server:INFO:---- Start !! ap_servd child process (port=22359[5757]). server.c(101)standalone_ap_serv_server:INFO:listen device name = br0 server.c(254)start_ap_serv_server:INFO:---- Start !! ap_servd child process (port=22616[5858]). server.c(101)standalone_ap_serv_server:INFO:listen device name = br0 MidLayerModDep.c(810) startModules :INFO:Started module rc_ap_serv 13[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanif Cannot assign requested address MidLayerModDep.c(810) startModules :INFO:Started module rc_wanif 1004[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pre Operation not supported Operation not supported MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pre 5038[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,auto_detect_retry MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect 3050[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_dummy MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_dummy 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_dhcpcd MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_dhcpcd 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_0 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_0 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_1 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_1 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_2 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_2 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_3 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_3 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_4 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_4 1[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_auto_detect_pppoecd_check MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_auto_detect_pppoecd_check 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_manual MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_manual 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_dhcpcd MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_dhcpcd 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_0 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_0 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_1 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_1 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_2 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_2 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_3 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_3 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_4 MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_4 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoecd_check MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoecd_check 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_post route: SIOC[ADD|DEL]RT: No such process mcsnoop: flush all snoop entry Cannot assign requested address MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_post 1055[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wanctl_pppoeroute MidLayerModDep.c(810) startModules :INFO:Started module rc_wanctl_pppoeroute 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_dnrd MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,dnrd MidLayerModDep.c(810) startModules :INFO:Started module rc_dnrd 6[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_ipfilter iptables: Bad rule (does a matching rule exist in that chain?) MidLayerModDep.c(810) startModules :INFO:Started module rc_ipfilter 287[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_ipfilter_simple MidLayerModDep.c(810) startModules :INFO:Started module rc_ipfilter_simple 40[mcleanup /proc/net/nf_conntrack sec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_ipfilter_user MidLayerModDep.c(810) startModules :INFO:Started module rc_ipfilter_user 2[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_nat MidLayerModDep.c(810) startModules :INFO:Started module rc_nat 21[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_routectl MidLayerModDep.c(810) startModules :INFO:Started module rc_routectl 10[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_lltd MidLayerModDep.c(810) startModules :INFO:Started module rc_lltd 61[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wsc killall: wscd: no process killed wscconfig.c(65) wsccmdctl_main :DEBUG:wscconfig start-reg wsccmdctl-ram.c(415) wsc_start :!:[[[[[[[[[[[[[[[[[[[[[[[[[ wsc_start ]]]]]]]]]]]]]]]]]]]]]]]]] MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,wscd wscconfig.c(67) wsccmdctl_main :DEBUG:wscconfig start-reg success MidLayerModDep.c(810) startModules :INFO:Started module rc_wsc 112[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_upnp buf_ReadConfigurationFile [/tmp/wsc_config_REG.txt]***************** CONFIGURED_MODE : 7 <config_mode>7 COnfMode = 7 UUID : 0x221acb40d79711ddb0101d4fc3355d70 <uuid>0x221acb40d79711ddb0101d4fc3355d70 DEVICE_NAME : BUFFDisable advatise PBC method ALO AirStation <dn>BUFFALO AirStation MANUFACTURER : BUFFALO INC. <manu>BUFFALO INC. MODEL_NAME : WHR-G300N <model>WHR-G300N FIX_PIN : 10864869 <pin>10864869 CONFIGURED : yes INTERFACE : ra0,ra1 <interface>ra0,ra1 <subif0>ra1 <if0>ra0 PROFILE : ra0;001D73D10998;WPAPSK;AES;41yh9yk1n9512;1;G;configured <profile> <prof>ra0 / 001D73D10998;WPAPSK;AES;41yh9yk1n9512;1;G;configured <found if ra0> PBC_WITH_AOSS : 1 <pbc_with_aoss>1 finished Read Configuration. <<<<<<<<buf_WscInitiDisable advatise PBC method alize>>>>>> wscd[buf_WscInitialize(405)] iwpriv ra0 set WscControlIf=ra0 wscd[buf_WscInitialize(408)] iwpriv ra0 set WscClrProfile=0 wscd[buf_WscInitialize(448)] iwpriv ra0 set WscConfMode=7 wscd[buf_WscInitialize(450)] iwpriv ra0 set WscConfStatus=2 wscd[buf_WscInitialize(452)] iwpriv ra0 set WscMode=1 wscd[buf_WscInitialize(456)] iwpriv ra0 set WscApPinCode=10864869 wscd[buf_WscInitialize(462)] iwpriv ra0 set "WscProductCode=221acb40d79711ddb0101d4fc3355d70:BUFFALO AirStation:BUFFALO INC.:WHR-G300N" wscd[buf_WscInitialize(465)] iwpriv ra0 set WscGetConf=0 wscd[buf_WscInitialize(467)] iwpriv ra0 set WscStatus=0 Cannot assign requested address iptables v1.3.5: Couldn't find target `UPNP-PREROUTING-CHAIN' Try `iptables -h' or 'iptables --help' for more information. iptables: iptables: No chain/target/match by that name No chain/target/match by that name wanctl-wanstate_check.c(41) wanstate_check_main :wanctl:Start wanstate_check Daemon MidLayerModDep.c(810) startModules :INFO:Started module rc_upnp 3069[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_wan_qos MidLayerModDep.c(810) startModules :INFO:Started module rc_wan_qos 0[msec] MidLayerModDep.c(798) startModules :INFO:Starting module rc_end_signal MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,lanctl MidLayerModDep.c(810) startModules :INFO:Started module rc_end_signal 11[msec] mcsnoop: flush all snoop entry ARPING to 192.168.11.1 from 192.168.11.1 via br0 Sent 1 probes (1 broadcast(s)) Received 0 reply MidLayerModDep.c(877) signalModules :INFO:signaling module rc_udhcpd MidLayerModDep.c(888) signalModules :INFO:signaled module rc_udhcpd MidLayerModDep.c(877) signalModules :INFO:signaling module rc_aoss_mssid MidLayerModDep.c(888) signalModules :INFO:signaled module rc_aoss_mssid MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_auto_detect MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,auto_detect_retry MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_auto_detect MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_post MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_post MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_pppoeroute MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_pppoeroute MidLayerModDep.c(877) signalModules :INFO:signaling module rc_dnrd MidLayerModDep.c(888) signalModules :INFO:signaled module rc_dnrd MidLayerModDep.c(877) signalModules :INFO:signaling module rc_ipfilter MidLayerModDep.c(888) signalModules :INFO:signaled module rc_ipfilter MidLayerModDep.c(877) signalModules :INFO:signaling module rc_ipfilter_simple MidLayerModDep.c(888) signalModules :INFO:signaled module rc_ipfilter_simple MidLayerModDep.c(877) signalModules :INFO:signaling module rc_routectl MidLayerModDep.c(888) signalModules :INFO:signaled module rc_routectl MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wsc MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wsc MidLayerModDep.c(877) signalModules :INFO:signaling module rc_upnp MidLayerModDep.c(888) signalModules :INFO:signaled module rc_upnp MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wan_qos MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wan_qos MidLayerModDep.c(877) signalModules :INFO:signaling module rc_udhcpd MidLayerModDep.c(888) signalModules :INFO:signaled module rc_udhcpd MidLayerModDep.c(877) signalModules :INFO:signaling module rc_aoss_mssid MidLayerModDep.c(888) signalModules :INFO:signaled module rc_aoss_mssid MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_auto_detect MidLayer.c(2557) ML_DoCommandWithCmdMax :WARN:find &,auto_detect_retry MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_auto_detect MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_post MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_post MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wanctl_pppoeroute MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wanctl_pppoeroute MidLayerModDep.c(877) signalModules :INFO:signaling module rc_dnrd MidLayerModDep.c(888) signalModules :INFO:signaled module rc_dnrd MidLayerModDep.c(877) signalModules :INFO:signaling module rc_ipfilter MidLayerModDep.c(888) signalModules :INFO:signaled module rc_ipfilter MidLayerModDep.c(877) signalModules :INFO:signaling module rc_ipfilter_simple MidLayerModDep.c(888) signalModules :INFO:signaled module rc_ipfilter_simple MidLayerModDep.c(877) signalModules :INFO:signaling module rc_routectl MidLayerModDep.c(888) signalModules :INFO:signaled module rc_routectl MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wsc MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wsc MidLayerModDep.c(877) signalModules :INFO:signaling module rc_upnp MidLayerModDep.c(888) signalModules :INFO:signaled module rc_upnp MidLayerModDep.c(877) signalModules :INFO:signaling module rc_wan_qos MidLayerModDep.c(888) signalModules :INFO:signaled module rc_wan_qos


Tags

toh/buffalo/whr-g300nv1.txt · Last modified: 2018/04/07 19:39 by tmomas