ASUS RT-AX59U
The RT-AX59U is a Dual Band WiFi 6 router based on the MediaTek Filogic 830 SoC with a quad-core Cortex-A53 @ 2.0 GHz, featuring three 1Gbit LAN ports, one 1Gbit WAN port, one USB 3.2 port and one USB 2.0 port in a clean case.
Supported Versions
Hardware Highlights
Installation
Flash Layout
Find out flash layout, then add the flash layout table here (copy, paste, modify the example).
Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.
Easy Installation
This section deals with
- How you install OpenWrt from a device freshly opened
- The steps required such as reset to factory defaults if the device has already been configured
Note: Reset router to factory defaults if it has been previously configured.
- Download .trx file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq (trx image is unofficial image, you may need to be used with caution.)
- Browse to
http://www.asusrouter.com/Advanced_FirmwareUpgrade_Content.asp
- Upload .trx file to router
- Wait for it to reboot
- trx image is initramfs version. You must upgrade to squashfs version.
- Browse to
http://192.168.1.1/cgi-bin/luci/admin/system/flash
if LuCI is installed - Upload squashfs version .bin file to router.
- Wait for it to reboot
- Telnet to 192.168.1.1 and set a root password, or browse to
http://192.168.1.1
if LuCI is installed.
OEM installation using the TFTP method
Specific values needed for tftp
Enter values for “FILL-IN” below
Bootloader tftp server IPv4 address | FILL-IN |
---|---|
Bootloader MAC address (special) | FILL-IN |
Firmware tftp image | Latest OpenWrt release (NOTE: Name must contain “tftp”) |
TFTP transfer window | FILL-IN seconds |
TFTP window start | approximately FILL-IN seconds after power on |
TFTP client required IP address | FILL-IN |
Upgrading OpenWrt
These are generic instructions. Update with your router's specifics.
LuCI Web Upgrade Process
- Browse to
http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/
LuCI Upgrade URL - Upload image file for sysupgrade to LuCI
- Wait for reboot
Terminal Upgrade Process
If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:
sysupgrade
mtd
Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
sysupgrade
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc sysupgrade /tmp/xxx.abc
mtd
If sysupgrade
does not support this router, use mtd
.
- Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc mtd write /tmp/xxx.abc linux && reboot
Debricking
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Specific Configuration
Please fill in real values for this device, then remove the EXAMPLEs
Network interfaces
The default network configuration is:
Interface Name | Description | Default configuration |
---|---|---|
br-lan | EXAMPLE LAN & WiFi | EXAMPLE 192.168.1.1/24 |
vlan0 (eth0.0) | EXAMPLE LAN ports (1 to 4) | EXAMPLE None |
vlan1 (eth0.1) | EXAMPLE WAN port | EXAMPLE DHCP |
wl0 | EXAMPLE WiFi | EXAMPLE Disabled |
Switch Ports (for VLANs)
Please fill in real values for this device, then remove the EXAMPLEs
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
Port | Switch port |
---|---|
Internet (WAN) | EXAMPLE 4 |
LAN 1 | EXAMPLE 3 |
LAN 2 | EXAMPLE 2 |
LAN 3 | EXAMPLE 1 |
LAN 4 | EXAMPLE 0 |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
Please fill in real values for this device, then remove the EXAMPLEs
The Asus RT-AX59U has the following buttons:
BUTTON | Event |
---|---|
EXAMPLE Reset | reset |
EXAMPLE Secure Easy Setup | ses |
EXAMPLE No buttons at all. | - |
Hardware
Info
Photos
Front:
Insert photo of front of the casing
Back:
Insert photo of back of the casing
Backside label:
Insert photo of backside label
Opening the Case
Note: This will void your warranty! There is a tiny sticker on the bottom hex screw that informs you of this.
Tools Needed
- 3/32 inch or 2.3mm hex driver
- Spudger
- Cross-head screwdriver (if you want to remove the PCB from the case)
Steps to Open Up
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port
Replace EXAMPLE by real values.
Serial connection parameters for Asus RT-AX59U @@Version@@ | EXAMPLE 115200, 8N1, 3.3V |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootloader mods
Hardware mods
None so far.
Bootlogs
OEM bootlog
COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE
OpenWrt bootlog
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.15.167 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24106-10cc5fcd00) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Sep 23 12:34:46 2024 [ 0.000000] Machine model: ASUS RT-AX59U [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff] [ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff] [ 0.000000] node 0: [mem 0x000000004ffc0000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s33112 r8192 d32424 u73728 [ 0.000000] pcpu-alloc: s33112 r8192 d32424 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 [ 0.000000] Kernel command line: ubi.mtd=UBI_DEV [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 498084K/524288K available (8448K kernel code, 904K rwdata, 1488K rodata, 448K init, 302K bss, 26204K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] Root IRQ handler: 0xffffffc008010090 [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000103] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000111] pid_max: default: 32768 minimum: 301 [ 0.000311] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000319] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.001346] rcu: Hierarchical SRCU implementation. [ 0.001607] smp: Bringing up secondary CPUs ... [ 0.001861] Detected VIPT I-cache on CPU1 [ 0.001885] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.001911] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.002166] Detected VIPT I-cache on CPU2 [ 0.002178] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.002189] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.002424] Detected VIPT I-cache on CPU3 [ 0.002434] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.002442] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.002468] smp: Brought up 1 node, 4 CPUs [ 0.002482] SMP: Total of 4 processors activated. [ 0.002486] CPU features: detected: 32-bit EL0 Support [ 0.002489] CPU features: detected: CRC32 instructions [ 0.002514] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.002568] CPU: All CPU(s) started at EL2 [ 0.002577] alternatives: patching kernel code [ 0.004847] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.004869] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.005014] pinctrl core: initialized pinctrl subsystem [ 0.005638] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.005882] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.005903] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.005921] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.006179] thermal_sys: Registered thermal governor 'fair_share' [ 0.006182] thermal_sys: Registered thermal governor 'bang_bang' [ 0.006186] thermal_sys: Registered thermal governor 'step_wise' [ 0.006189] thermal_sys: Registered thermal governor 'user_space' [ 0.006347] ASID allocator initialised with 65536 entries [ 0.006670] pstore: Registered ramoops as persistent store backend [ 0.006674] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.014357] cryptd: max_cpu_qlen set to 1000 [ 0.015856] SCSI subsystem initialized [ 0.015941] libata version 3.00 loaded. [ 0.016756] clocksource: Switched to clocksource arch_sys_counter [ 0.017283] NET: Registered PF_INET protocol family [ 0.017355] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.017714] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.017726] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.017732] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.017753] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 0.017797] TCP: Hash tables configured (established 4096 bind 4096) [ 0.017854] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.017866] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.017966] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.017982] PCI: CLS 0 bytes, default 64 [ 0.019852] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.022544] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.022558] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.044855] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.045701] gpio-export gpio-export: 1 gpio(s) exported [ 0.048618] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.050334] printk: console [ttyS0] disabled [ 0.070484] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 121, base_baud = 2500000) is a ST16650V2 [ 0.714272] printk: console [ttyS0] enabled [ 0.719056] mtk_rng 1020f000.rng: registered RNG driver [ 0.719115] hwrng: no data available [ 0.727852] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.735985] loop: module loaded [ 0.739156] Loading iSCSI transport class v2.0-870. [ 0.745535] spi-nand spi0.0: ESMT SPI NAND was found. [ 0.750598] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.758840] 2 fixed-partitions partitions found on MTD device spi0.0 [ 0.765177] Creating 2 MTD partitions on "spi0.0": [ 0.769961] 0x000000000000-0x000000400000 : "Bootloader" [ 0.778939] 0x000000400000-0x000008000000 : "UBI_DEV" [ 1.017931] mtk_soc_eth 15100000.ethernet: generated random MAC address be:3f:5c:fe:0e:5f [ 1.028738] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009600000, irq 129 [ 1.038246] i2c_dev: i2c /dev entries driver [ 1.043445] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.051889] NET: Registered PF_INET6 protocol family [ 1.057455] Segment Routing with IPv6 [ 1.061124] In-situ OAM (IOAM) with IPv6 [ 1.065058] NET: Registered PF_PACKET protocol family [ 1.070125] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.083148] 8021q: 802.1Q VLAN Support v1.8 [ 1.088250] pstore: Using crash dump compression: deflate [ 1.137152] mt7530-mdio mdio-bus:1f: no interrupt support [ 1.148444] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode [ 1.157560] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.166757] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.186958] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.206946] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.226931] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=POLL) [ 1.238080] DSA: tree 0 setup [ 1.241345] ubi0: default fastmap pool size: 45 [ 1.245864] ubi0: default fastmap WL pool size: 22 [ 1.250649] ubi0: attaching mtd1 [ 3.384916] ubi0: scanning is finished [ 3.413238] ubi0: attached mtd1 (name "UBI_DEV", size 124 MiB) [ 3.419073] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.425926] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.432694] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.439636] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0 [ 3.445622] ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128 [ 3.452824] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 127872481 [ 3.461846] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20 [ 3.471046] ubi0: background thread "ubi_bgt0d" started, PID 435 [ 3.474827] block ubiblock0_5: created from ubi0:5(rootfs) [ 3.482509] ubiblock: device ubiblock0_5 (rootfs) set to be root filesystem [ 3.489590] clk: Disabling unused clocks [ 3.509971] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 3.517263] Freeing unused kernel memory: 448K [ 3.521722] Run /sbin/init as init process [ 3.525801] with arguments: [ 3.528755] /sbin/init [ 3.531446] with environment: [ 3.534569] HOME=/ [ 3.536916] TERM=linux [ 3.796768] random: crng init done [ 3.880918] init: Console is alive [ 3.884408] init: - watchdog - [ 4.612548] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.655739] usbcore: registered new interface driver usbfs [ 4.661267] usbcore: registered new interface driver hub [ 4.666591] usbcore: registered new device driver usb [ 4.674989] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator [ 4.682406] xhci-mtk 11200000.usb: supply vusb33 not found, using dummy regulator [ 4.690567] xhci-mtk 11200000.usb: xHCI Host Controller [ 4.695794] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1 [ 4.706264] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010 [ 4.715412] xhci-mtk 11200000.usb: irq 123, io mem 0x11200000 [ 4.721260] xhci-mtk 11200000.usb: xHCI Host Controller [ 4.726471] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2 [ 4.733851] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed [ 4.741195] hub 1-0:1.0: USB hub found [ 4.744946] hub 1-0:1.0: 2 ports detected [ 4.749247] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.757576] hub 2-0:1.0: USB hub found [ 4.761324] hub 2-0:1.0: 1 port detected [ 4.767578] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.779319] init: - preinit - [ 5.206799] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk [ 5.316885] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 5.325321] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 5.326382] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.340778] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 7.573362] UBIFS (ubi0:6): Mounting in unauthenticated mode [ 7.579099] UBIFS (ubi0:6): background thread "ubifs_bgt0_6" started, PID 596 [ 7.712041] UBIFS (ubi0:6): recovery needed [ 8.033487] UBIFS (ubi0:6): recovery completed [ 8.037979] UBIFS (ubi0:6): UBIFS: mounted UBI device 0, volume 6, name "rootfs_data" [ 8.045790] UBIFS (ubi0:6): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 8.055683] UBIFS (ubi0:6): FS size: 109961216 bytes (104 MiB, 866 LEBs), max 877 LEBs, journal size 5459968 bytes (5 MiB, 43 LEBs) [ 8.067483] UBIFS (ubi0:6): reserved for root: 4952683 bytes (4836 KiB) [ 8.074079] UBIFS (ubi0:6): media format: w5/r0 (latest is w5/r0), UUID 6CC33461-BFFA-4E79-BC30-8EF4463AE060, small LPT model [ 8.112705] mount_root: loading kmods from internal overlay [ 8.472889] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 8.573392] usb-storage 2-1:1.0: USB Mass Storage device detected [ 8.579804] scsi host0: usb-storage 2-1:1.0 [ 8.584224] usbcore: registered new interface driver usb-storage [ 8.596479] usbcore: registered new interface driver uas [ 8.601998] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/* [ 9.106214] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 9.129450] block: extroot: not configured [ 9.139246] mount_root: switching to ubifs overlay [ 9.165560] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 9.186060] urandom-seed: Seeding with /etc/urandom.seed [ 9.294215] procd: - early - [ 9.297178] procd: - watchdog - [ 9.607665] scsi 0:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6 [ 9.616351] sd 0:0:0:0: [sda] 242221056 512-byte logical blocks: (124 GB/116 GiB) [ 9.624330] sd 0:0:0:0: [sda] Write Protect is off [ 9.629121] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00 [ 9.634633] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 9.797146] sda: sda1 [ 9.801244] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 10.299700] procd: - watchdog - [ 10.310957] procd: - ubus - [ 10.432772] procd: - init - [ 11.363069] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.377596] GACT probability on [ 11.382964] Mirror/redirect action on [ 11.394835] u32 classifier [ 11.397566] input device check on [ 11.401212] Actions configured [ 11.434570] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 11.455699] Loading modules backported from Linux version v6.1.110-0-g5f55cad62cc9d [ 11.463375] Backport generated by backports.git v6.1.110-1-0-g965f73fc [ 11.501516] urngd: v1.0.2 started. [ 11.515513] xt_time: kernel timezone is -0000 [ 11.876805] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221012174648a [ 11.876805] [ 12.243463] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221012174725 [ 12.406645] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221012174937 [ 12.553627] mt798x-wmac 18000000.wifi: eeprom load fail, use default bin [ 12.563953] mt798x-wmac 18000000.wifi: missing precal data, size=403472 [ 12.570627] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0' [ 12.618439] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1' [ 15.532941] PPP generic driver version 2.4.2 [ 15.537935] NET: Registered PF_PPPOX protocol family [ 15.545542] kmodloader: done loading kernel modules from /etc/modules.d/* [ 17.248756] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: . Quota mode: disabled. [ 20.283009] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 20.299611] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 20.308064] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 20.308147] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 20.326431] device eth0 entered promiscuous mode [ 20.331544] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 20.341507] br-lan: port 1(lan1) entered blocking state [ 20.346722] br-lan: port 1(lan1) entered disabled state [ 20.353341] device lan1 entered promiscuous mode [ 20.367961] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode [ 20.377781] br-lan: port 2(lan2) entered blocking state [ 20.383000] br-lan: port 2(lan2) entered disabled state [ 20.389910] device lan2 entered promiscuous mode [ 20.400882] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode [ 20.410699] br-lan: port 3(lan3) entered blocking state [ 20.415919] br-lan: port 3(lan3) entered disabled state [ 20.422951] device lan3 entered promiscuous mode [ 20.435601] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode [ 20.912400] br-lan: port 4(phy1-ap0) entered blocking state [ 20.918059] br-lan: port 4(phy1-ap0) entered disabled state [ 20.923821] device phy1-ap0 entered promiscuous mode [ 20.928967] br-lan: port 4(phy1-ap0) entered blocking state [ 20.934541] br-lan: port 4(phy1-ap0) entered forwarding state [ 20.940919] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 20.949960] device phy1-ap0 left promiscuous mode [ 20.954750] br-lan: port 4(phy1-ap0) entered disabled state [ 21.019842] br-lan: port 4(phy1-ap0) entered blocking state [ 21.025428] br-lan: port 4(phy1-ap0) entered disabled state [ 21.031249] device phy1-ap0 entered promiscuous mode [ 21.036339] br-lan: port 4(phy1-ap0) entered blocking state [ 21.041923] br-lan: port 4(phy1-ap0) entered forwarding state [ 21.287401] br-lan: port 4(phy1-ap0) entered disabled state [ 22.036551] br-lan: port 5(phy0-ap0) entered blocking state [ 22.042175] br-lan: port 5(phy0-ap0) entered disabled state [ 22.047924] device phy0-ap0 entered promiscuous mode [ 22.052987] br-lan: port 5(phy0-ap0) entered blocking state [ 22.058597] br-lan: port 5(phy0-ap0) entered forwarding state [ 22.065176] device phy0-ap0 left promiscuous mode [ 22.070005] br-lan: port 5(phy0-ap0) entered disabled state [ 22.097989] br-lan: port 5(phy0-ap0) entered blocking state [ 22.103590] br-lan: port 5(phy0-ap0) entered disabled state [ 22.109441] device phy0-ap0 entered promiscuous mode [ 22.114510] br-lan: port 5(phy0-ap0) entered blocking state [ 22.120124] br-lan: port 5(phy0-ap0) entered forwarding state [ 22.296850] br-lan: port 5(phy0-ap0) entered disabled state [ 23.532333] mt7530-mdio mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx [ 23.532352] br-lan: port 3(lan3) entered blocking state [ 23.545465] br-lan: port 3(lan3) entered forwarding state [ 24.652083] mt7530-mdio mdio-bus:1f wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 24.652095] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready [ 31.060191] IPv6: ADDRCONF(NETDEV_CHANGE): phy0-ap0: link becomes ready [ 31.066940] br-lan: port 5(phy0-ap0) entered blocking state [ 31.072499] br-lan: port 5(phy0-ap0) entered forwarding state
Notes
Space for additional notes, links to forum threads or other resources.