WAVLINK AC1200 (WL-WN572HG3)

The WAVLINK AC1200 is an outdoor device with 2.4 GHz and 5 GHz radios. Due to external antennas it might be well suited catch up signals in situations with public WiFi on camping ground or on ships in marinas.

WAVLINK AC1200 / 7Links AC1200

Also known as:
- 7Links NX-4812-919 (German)
- Wavlink AERIAL HD4

Partially supported (no WAN yet).

A partial working version can be taken from: rp-n53

  1. rename to firmware.bin
  2. set host IP to 192.168.10.100
  3. start tftp server
  4. connect power to the router
  5. over UART wait for uBoot menu
  6. select option “2: Load system code then write to Flash via TFTP.”
  7. done

Firmware from the Netgear ex3700_ex3800 or EX6120 has also been tested working, and adds 5GHz WiFi support. This is flashed in the same way as the above. Please allow a few minutes on first boot for SSH key generation & flash initialization. If first boot fails, reflash the firmware bin and the subsequent boot should succeed.

Available via FTP here: GPL Sources
Please note, this FTP will not produce directory listings if browsed manually, the file will need to be downloaded directly. The filesize is 1,784,547,728 bytes.

CPU Ram Flash Wi-Fi chip Network 2.4 GHz 5 GHz USB Serial JTag LEDs Buttons
MT7620A @ 580 MHz 64 MiB 8 MiB MT7612E (2T2R) 2x 10/100 (WAN: DC24V/0.5A, Passive PoE) Yes, b/g/n/ac Yes, b/g/n/ac Yes (USB 2.0) Yes ? 7 1 (reset)

The WAVLINK AC1200 has the following buttons:

BUTTON Event
Reset reset

The power LED does not seem to be on a GPIO (all GPIOs were software toggled within stock firmware for the discovery process). The stock firmware does not seem to utilize it for status messages either.

GPIO FUNCTION STATE
1 Reset Button Active Low
12 Wifi Signal Mid LED Active Low
13 Wifi Signal High LED Active Low
41 LAN LED Active Low
43 Wifi Signal Low LED Active Low
44 WAN LED Active Low
72 Wifi LED Active Low

The following connectors can be found on the PCB:

Connector Description PINs
J1 POE Center Tap (CT1, CT2) and Signal Path (SP1, SP2)
J2 RS232 VCC (3.3V), TX, RX, GND
J3 USB D+ middle towards J4, D- middle towards J2
J4 24V 2x 24V, 2x GND
near J3 5 V 5V, GND

The middle pin of J3 are connected to D+ and D-. The outer pin on the RJ45 side is GND then D+ then D-. There is no VCC on the last pin. There are two pins near the USB connector: the pin towards the LEDs is 5V the other is GND.

⇐ LEDs ⇐ J2 J4 ⇒ RJ45 ⇒
? D- D+ GND
⇐ LEDs RJ45 ⇒
5V GND

A simple test with a USB storage device shows a working USB 2.0 port.

[ 2727.416000] usb 1-1: new high speed USB device using rt3xxx-ehci and address 4
[ 2727.560000] scsi0 : usb-storage 1-1:1.0
[ 2728.364000] usb 1-1: USB disconnect, address 4
[ 2729.872000] usb 1-1: new high speed USB device using rt3xxx-ehci and address 5
[ 2730.016000] scsi1 : usb-storage 1-1:1.0
[ 2731.040000] scsi 1:0:0:0: Direct-Access     General  USB Flash Disk   1.00 PQ: 0 ANSI: 2
[ 2731.068000] sd 1:0:0:0: [sda] 15669248 512-byte logical blocks: (8.02 GB/7.47 GiB)
[ 2731.104000] sd 1:0:0:0: [sda] Write Protect is off
[ 2731.112000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 2731.132000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 2731.148000]  sda: sda1
[ 2731.156000] sd 1:0:0:0: [sda] Assuming drive cache: write through
[ 2731.168000] sd 1:0:0:0: [sda] Attached SCSI removable disk
start mount sda1
start mount sda
[ 2733.524000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2733.568000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
mount /dev/sda1 successfully
ntfs-3g /dev/sda error

The drive is mounted automaticaly in the orignal firmware:

# mount
rootfs on / type rootfs (rw)
proc on /proc type proc (rw,relatime)
none on /var type ramfs (rw,relatime)
none on /dev type ramfs (rw,relatime)
none on /etc type ramfs (rw,relatime)
none on /tmp type ramfs (rw,relatime)
none on /media type ramfs (rw,relatime)
none on /sys type sysfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/mtdblock5 on /vendor type jffs2 (rw,relatime)
mdev on /dev type ramfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/sda1 on /media/sda1 type vfat (rw,relatime,fmask=0000,dmask=0000,allow_utime=0022,codepage=cp950,iocharset=utf8,shortname=mixed,errors=remount-ro)

Due to the fact the SP2 SP1 CT2 CT1 pin holes are exposed there might be a chance to use a Si3402 to provide “real POE” instead of the passive POE implemented already.

https://www.mouser.com/datasheet/2/368/Si3402-B-1666231.pdf

Architecture MIPS 24KEc
Vendor Mediatek
Bootloader U-Boot 1.1.3 (Jan 20 2018 - 15:44:18)
System-On-Chip MT7620A ver:2 eco:6 - MIPS 24K V4.12
CPU/Speed MT7620A @ 580 MHz
Flash-Chip GD25Q64B
Flash size 8 MiB
RAM 64 MiB
Wireless MT7620A 2.4GHz 802.11bgn, MT7610E 5 GHz a/ac
Ethernet 10/100 Mbit/s w/ vlan support
Switch MT7530WU
USB 1x 2.0
Serial Yes
JTAG not yet identified
Type Description Datasheet
AH1943 25Q64CSIG3 UA2430 SPI flash 64M-BIT https://www.winbond.com/resource-files/w25q64fw_revd_032513.pdf
RTL8211F K2102H1 GK08 Realtek Ethernet transceiver 10/100/1000 MBit https://datasheet.lcsc.com/szlcsc/1909021205_Realtek-Semicon-RTL8211F-CG_C187932.pdf
LXK 6626 1936 WiFi Amplifier
LSC LSP5527 1908H3 2A 27V Synchronous Buck Converter http://www.liteon-semi.com/upfiles/tecfile01497425681.pdf
S158adH DC-DC Converter Like?: https://datasheet.lcsc.com/szlcsc/2007241904_TMI-STI3411A_C708879.pdf
MEDIATEK MT7612EN 2015-8MJL ETPS3843 802.11ac, Wi-Fi 5 (a/b/g/n/ac) 2.4GHz, 5GHz http://www.trolink.cn/UploadFiles/Product/20160419154055_39193.pdf
MEDIATEK MT7620A 2010-BMTH GTPRYF67H CPU, Wi-Fi 4 (n) 2.4GHz http://download.villagetelco.org/hardware/MT7620/
SCTF 40.000 crystal 40 MHz
A3R12E40DBF-AH 946ZENB0 8C031297G-F 512Mb DDRII SDRAM (64M)
85743 035468 1 2002 MX RF Frontend https://www.skyworksinc.com/-/media/SkyWorks/Documents/Products/2901-3000/SKY85743_31_205481A_PS.pdf
TF5040 2017H Ethernet transformer
LGE SS310 Schottky Barrier Rectifiers 100V/3A https://datasheet.lcsc.com/szlcsc/1811131655_LGE-SS310_C330484.pdf
dmesg
deice id : c8 40 17 c8 40 (4017c840)
GD25Q64B(c8 4017c840) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 6 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000780000 : "Kernel"
0x000000780000-0x000000800000 : "Vendor"
cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00800000 00010000 "ALL"
mtd1: 00030000 00010000 "Bootloader"
mtd2: 00010000 00010000 "Config"
mtd3: 00010000 00010000 "Factory"
mtd4: 00730000 00010000 "Kernel"
mtd5: 00080000 00010000 "Vendor"
deice id : c8 40 17 c8 40 (4017c840)
GD25Q64B(c8 4017c840) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
DECIMAL       HEXADECIMAL     DESCRIPTION
--------------------------------------------------------------------------------
73296         0x11E50         U-Boot version string, "U-Boot 1.1.3 (Jan 13 2018 - 15:43:35)"
210408        0x335E8         Linux kernel version 2.6.36
327680        0x50000         uImage header, header size: 64 bytes, header CRC: 0xC19BA121, created: 2019-10-10 09:32:20, image size: 6392262 bytes, Data Address: 0x80000000, Entry Point: 0x8000C310, data CRC: 0xFD48103B, OS: Linux, CPU: MIPS, image type: OS Kernel Image, compression type: lzma, image name: "WN535K1"
327744        0x50040         LZMA compressed data, properties: 0x5D, dictionary size: 33554432 bytes, uncompressed size: 10769928 bytes
7864320       0x780000        JFFS2 filesystem, little endian

There really is no “seal” it's just o rings and washers and nuts.

Remove the antenna and the silicone rubber boots, then the SMA connector nut and washer for all for antennas. Then gently unscrew the bottom cap, there is an o-ring between the cap and the body, dont damage it. Slide out of bottom with ease.

There is a simple web command interface with root permissions:

http://ip/webcmd.shtml

Please note that this (as well as serial console login) has been removed in newer firmware versions (WN572HG3-A_2021.07.21.bin). You will need http://files.wavlink.com/fw/OUTDOOR%20AP/WN572HG3-WAVLINK_WO_20200717.bin or earlier.

By the use of the backdoor a simple command 'telnetd' will start a telnet server on port 2323.

telnetd USER: admin2860
PASS: <the password given at the initial wizard>

port.serial general information about the serial port, serial port cable, etc.

Serial connection parameters
for 7Links AC1200
57600, 8N1
Vcc RX TX GND
3.3V RX (PC) / TX (Router) TX (PC) / RX (Router) GND

Advice: while you are in there strengthen the antenna connectors with more solder and epoxy. Several devs' antennas have broken away from the board a few times due to wind & weather, resolved with quick 2 part epoxy.

U-Boot 1.1.3 (Jan 20 2018 - 15:44:18) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fa0000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 29 spi device id: c8 40 17 c8 40 (4017c840) find flash: GD25Q64B raspi_read: from:30000 len:1000 raspi_read: from:30000 len:1000 ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC 7620_MP (Port5<->Phy) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jan 20 2018 Time:15:44:18 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Read PhyID ID0:FFFF ID1:FFFF!! Read PhyID ID0:FFFF ID1:FFFF!! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Enter boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3  4  3  2  1  0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: WN572HG3-A Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5612804 Bytes = 5.4 MB Load Address: 80000000 Entry Point: 8000c310 raspi_read: from:50040 len:55a504 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c310) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 [ 0.000000] Linux version 2.6.36+ (root@ubuntu) (gcc version 3.4.2) #3743 Thu Feb 28 15:11:23 CST 2019 [ 0.000000] [ 0.000000] The CPU feqenuce set to 580 MHz [ 0.000000] PCIE: bypass PCIe DLL. [ 0.000000] PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 [ 0.000000] disable all power about PCIe [ 0.000000] CPU revision is: 00019650 (MIPS 24Kc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00010230 [ 0.000000] Readback ErrCtl register=00010230 [ 0.000000] Memory: 55332k/65536k available (4589k kernel code, 10204k reserved, 842k data, 3912k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.008000] Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) [ 0.096000] pid_max: default: 32768 minimum: 301 [ 0.100000] Mount-cache hash table entries: 512 [ 0.104000] NET: Registered protocol family 16 [ 0.108000] RALINK_GPIOMODE = 1a101d [ 0.112000] RALINK_GPIOMODE = 18101d [ 0.116000] PPLL_CFG1=0xe7c000 [ 0.120000] MT7620 PPLL lock [ 0.124000] PPLL_DRV =0x80080504 [ 0.128000] start PCIe register access [ 0.628000] RALINK_RSTCTRL = 2400000 [ 0.632000] RALINK_CLKCFG1 = 75afffc0 [ 0.636000] [ 0.636000] *************** MT7620 PCIe RC mode ************* [ 1.136000] PCIE0 enabled [ 1.140000] Port 0 N_FTS = 1b105000 [ 1.144000] init_rt2880pci done [ 1.148000] bio: create slab <bio-0> at 0 [ 1.152000] vgaarb: loaded [ 1.156000] SCSI subsystem initialized [ 1.160000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) [ 1.164000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 1.168000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] [ 1.172000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 1.176000] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] [ 1.180000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] [ 1.184000] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff] [ 1.188000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] [ 1.192000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 1.196000] pci 0000:00:00.0: bridge window [io disabled] [ 1.200000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 1.204000] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] [ 1.208000] BAR0 at slot 0 = 0 [ 1.212000] bus=0x0, slot = 0x0 [ 1.216000] res[0]->start = 0 [ 1.220000] res[0]->end = 0 [ 1.224000] res[1]->start = 20200000 [ 1.228000] res[1]->end = 2020ffff [ 1.232000] res[2]->start = 0 [ 1.236000] res[2]->end = 0 [ 1.240000] res[3]->start = 0 [ 1.244000] res[3]->end = 0 [ 1.248000] res[4]->start = 0 [ 1.252000] res[4]->end = 0 [ 1.256000] res[5]->start = 0 [ 1.260000] res[5]->end = 0 [ 1.264000] bus=0x1, slot = 0x0 [ 1.268000] res[0]->start = 20000000 [ 1.272000] res[0]->end = 200fffff [ 1.276000] res[1]->start = 0 [ 1.280000] res[1]->end = 0 [ 1.284000] res[2]->start = 0 [ 1.288000] res[2]->end = 0 [ 1.292000] res[3]->start = 0 [ 1.296000] res[3]->end = 0 [ 1.300000] res[4]->start = 0 [ 1.304000] res[4]->end = 0 [ 1.308000] res[5]->start = 0 [ 1.312000] res[5]->end = 0 [ 1.316000] Switching to clocksource Ralink Systick timer [ 1.320000] NET: Registered protocol family 2 [ 1.328000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 1.340000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 1.356000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 1.368000] TCP: Hash tables configured (established 2048 bind 2048) [ 1.380000] TCP reno registered [ 1.388000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 1.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 1.412000] NET: Registered protocol family 1 [ 5.680000] Load Kernel WDG Timer Module [ 5.688000] Load Ralink Timer0 Module [ 5.700000] fuse init (API version 7.15) [ 5.708000] msgmni has been set to 108 [ 5.716000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 5.728000] io scheduler noop registered (default) [ 5.964000] Ralink gpio 18b01d [ 5.972000] Ralink gpio driver initialized [ 5.980000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 5.992000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A [ 6.008000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A [ 6.024000] brd: module loaded [ 6.032000] deice id : c8 40 17 c8 40 (4017c840) [ 6.040000] GD25Q64B(c8 4017c840) (8192 Kbytes) [ 6.048000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 [ 6.068000] Creating 5 MTD partitions on "raspi": [ 6.076000] 0x000000000000-0x000000800000 : "ALL" [ 6.088000] 0x000000000000-0x000000030000 : "Bootloader" [ 6.100000] 0x000000030000-0x000000040000 : "Config" [ 6.112000] 0x000000040000-0x000000050000 : "Factory" [ 6.124000] 0x000000050000-0x000001000000 : "Kernel" [ 6.132000] mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000 [ 6.152000] rdm_major = 253 [ 6.160000] SMACCR1 -- : 0x0000803f [ 6.164000] SMACCR0 -- : 0x5db7588f [ 6.172000] Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! [ 6.192000] SMACCR1 -- : 0x0000803f [ 6.200000] SMACCR0 -- : 0x5db7588f [ 6.208000] PROC INIT OK! [ 6.212000] PPP generic driver version 2.4.2 [ 6.220000] PPP MPPE Compression module registered [ 6.232000] NET: Registered protocol family 24 [ 6.240000] PPTP driver version 0.8.5 [ 6.252000] [7620]: [ 6.256000] [ 6.256000] === pAd = c0147000, size = 985592 === [ 6.256000] [ 6.272000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 6.284000] <-- RTMPAllocAdapterBlock, Status=0 [ 6.292000] [7620]:AP Driver version-2.7.2.1 [ 6.300000] nf_conntrack version 0.5.0 (864 buckets, 3456 max) [ 6.312000] IPVS: Registered protocols () [ 6.320000] IPVS: Connection hash table configured (size=4096, memory=32Kbytes) [ 6.336000] IPVS: ipvs loaded. [ 6.340000] GRE over IPv4 demultiplexor driver [ 6.352000] gre: can't add protocol [ 6.356000] ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone [ 6.372000] TCP cubic registered [ 6.380000] NET: Registered protocol family 10 [ 6.388000] NET: Registered protocol family 17 [ 6.396000] L2TP core driver, V2.0 [ 6.404000] PPPoL2TP kernel driver, V2.0 [ 6.412000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> [ 6.424000] All bugs added by David S. Miller <davem@redhat.com> [ 6.440000] Warning: unable to open an initial console. [ 6.472000] Freeing unused kernel memory: 3912k freed [ 6.492000] Algorithmics/MIPS FPU Emulator v1.5 Welcome to __ ___ _____ _____ _ _______ ______ _____ _ ___ | \ / || ___|| __ \ | || __ ||__ __|| ___|| | / / | ^ || |__ | | \ \| || | | | | | | |__ | |/ / | | | || ___|| | | || || |__| | | | | ___|| \ | | | || |___ | |__/ /| || __ | | | | |___ | |\ \ |__| |___||_____||_____/ |_||_| |_| |_| |_____||_| \__\ = Everyday Genius = killall: kv_daemon: no process killed killall: monitor: no process killed killall: network_status: no process killed killall: touchlink: no process killed killall: sync_server: no process killed killall: sync_client: no process killed killall: pppoe_check.sh: no process killed killall: turbo: no process killed rm: cannot remove '/tmp/Link': No such file or directory rmmod: wlink_igd.ko: No such file or directory Password for 'admin2860' changed /sbin/internet.sh: line 719: storage.sh: not found Interface doesn't accept private ioctl... set (8BE2): Network is down rai0 no private ioctls. rmmod: hw_nat: No such file or directory ##### disable 1st wireless interface ##### ##### disable 2nd wireless interface ##### ##### disable 3rd wireless interface ##### rmmod: rt2860v2_ap_net: No such file or directory rmmod: rt2860v2_ap: No such file or directory rmmod: rt2860v2_ap_util: No such file or directory rmmod: rlt_wifi: No such file or directory insmod: rt2860v2_ap_util.ko: module not found insmod: rt2860v2_ap.ko: module not found insmod: rt2860v2_ap_net.ko: module not found [ 13.832000] register rt2860 [ 13.852000] [ 13.852000] [ 13.852000] === pAd = c0782000, size = 2174520 === [ 13.852000] [ 13.872000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 13.880000] <-- RTMPAllocAdapterBlock, Status=0 [ 13.892000] pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000! [ 13.904000] device_id =0x7662 [ 13.908000] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a [ 13.928000] chip_id1="2860", chip_id2="7612e", pAd->MACVersion=0x76623000 [ 13.940000] chip_id1=0x0, chip_id2=0x0, pAd->MACVersion=0x76623000 [ 13.952000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 [ 13.964000] RtmpEepromGetDefault::e2p_dafault=2 [ 13.976000] NVM is efuse and the information is too less to bring up the interface [ 13.988000] Force to use Flash mode [ 13.996000] NVM is FLASH mode (pAd->flash_offset = 0x8000) [ 14.008000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 14.308000] [7620]:RX DESC a244b000 size = 2048 [ 14.432000] [7620]:APSDCapable[0]=0 [ 14.440000] [7620]:APSDCapable[1]=0 [ 14.448000] [7620]:APSDCapable[2]=0 [ 14.452000] [7620]:APSDCapable[3]=0 [ 14.460000] [7620]:APSDCapable[4]=0 [ 14.468000] [7620]:APSDCapable[5]=0 [ 14.476000] [7620]:APSDCapable[6]=0 [ 14.480000] [7620]:APSDCapable[7]=0 [ 14.488000] [7620]:APSDCapable[8]=0 [ 14.496000] [7620]:APSDCapable[9]=0 [ 14.504000] [7620]:APSDCapable[10]=0 [ 14.508000] [7620]:APSDCapable[11]=0 [ 14.516000] [7620]:APSDCapable[12]=0 [ 14.524000] [7620]:APSDCapable[13]=0 [ 14.532000] [7620]:APSDCapable[14]=0 [ 14.536000] [7620]:APSDCapable[15]=0 [ 14.544000] [7620]:default ApCliAPSDCapable[0]=0 [ 14.560000] [7620]:Key1Str is Invalid key length(0) or Type(0) [ 14.572000] [7620]:Key2Str is Invalid key length(0) or Type(0) [ 14.584000] [7620]:Key3Str is Invalid key length(0) or Type(0) [ 14.596000] [7620]:Key4Str is Invalid key length(0) or Type(0) [ 14.644000] [7620]:RTMPSetDefaultChannel() : default channel to 1 [ 14.656000] [7620]:1. Phy Mode = 9 [ 14.664000] [7620]:2. Phy Mode = 9 [ 14.668000] [7620]:--> NICReadEEPROMParameters [ 14.676000] [7620]:E2PROM MAC: =80:3f:5d:b7:58:91 [ 14.688000] [7620]:20-E2P[0x36]:(c004),EXT LNA|PA on! [ 14.696000] [7620]:E2PROM: D0 target power=0xff20 [ 14.708000] [7620]:E2PROM: 40 MW Power Delta= 0 [ 14.716000] [7620]:3. Phy Mode = 9 [ 14.724000] [7620]:AntCfgInit: primary/secondary ant 0/1 [ 14.728000] [7620]:Initialize RF Central Registers for E2 !!! [ 14.748000] [7620]:Initialize RF Central Registers for E3 !!! [ 14.756000] [7620]:Initialize RF Channel Registers for E2 !!! [ 14.768000] [7620]:Initialize RF Channel Registers for E3 !!! [ 14.780000] [7620]:Initialize RF DCCal Registers for E2 !!! [ 14.792000] [7620]:Initialize RF DCCal Registers for E3 !!! [ 14.804000] [7620]:Change as GPIO Mode(0x18b01d) [ 14.812000] [7620]:D1 = 3, D2 = 12, CalCode = 21 !!! [ 14.824000] [7620]:RT6352_Temperature_Init : BBPR49 = 0x3 [ 14.836000] [7620]:RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff9 [ 14.852000] [7620]:Current Temperature from BBP_R49=0xfffffffa [ 14.868000] [7620]: TX BW Filter Calibration !!! [ 15.004000] [7620]: RX BW Filter Calibration !!! [ 15.260000] [7620]:LOFT Calibration Done! [ 15.272000] [7620]:IQCalibration Start! [ 15.292000] [7620]:IQCalibration Done! CH = 0, (gain= 0, phase=3c) [ 15.308000] [7620]:IQCalibration Start! [ 15.328000] [7620]:IQCalibration Done! CH = 1, (gain= 0, phase= 2) [ 15.340000] [7620]:TX IQ Calibration Done! [ 15.348000] [7620]:RXIQ si=495, sq=486, riq=-13, bbpval 495, vga_idx 0 [ 15.364000] [7620]:RXIQ si=4404, sq=4324, riq=-120, bbpval 4404, vga_idx 5 [ 15.376000] [7620]:RXIQ si=7090, sq=6943, riq=-222, bbpval 7090, vga_idx 6 [ 15.392000] [7620]:RXIQ si=11181, sq=10949, riq=-316, bbpval 11181, vga_idx 7 [ 15.404000] [7620]:Sigma_i=1057, Sigma_q=1046, R_iq=-3160 [ 15.416000] [7620]:RXIQ Sigma_i=1057, Sigma_q=1046, R_iq=-3160 [ 15.428000] [7620]:RXIQ G_imb=-1, Ph_rx=-6 [ 15.436000] [7620]:RXIQ si=767, sq=754, riq=-16, bbpval 767, vga_idx 0 [ 15.448000] [7620]:RXIQ si=4204, sq=4156, riq=-37, bbpval 4204, vga_idx 4 [ 15.464000] [7620]:RXIQ si=6359, sq=6277, riq=-53, bbpval 6359, vga_idx 5 [ 15.476000] [7620]:RXIQ si=10204, sq=10069, riq=-100, bbpval 10204, vga_idx 6 [ 15.492000] [7620]:Sigma_i=1010, Sigma_q=1003, R_iq=-1000 [ 15.504000] [7620]:RXIQ Sigma_i=1010, Sigma_q=1003, R_iq=-1000 [ 15.516000] [7620]:RXIQ G_imb=0, Ph_rx=-2 [ 15.524000] [7620]:Change as Normal Mode(0x8b01d) [ 15.532000] [7620]:After Change, now GPIO_MODE value is 0x8b01d [ 15.544000] [7620]:RT6352_Init_ExtPA_ExtLNA: Enable Ext-PA. init MAC [ 15.556000] [7620]:RT6352_Init_ExtPA_ExtLNA: Enable Ext-LNA. [ 15.568000] [7620]:RT6352_Init_ExtPA_ExtLNA: Enable Ext-PA. [ 15.580000] [7620]:RT6352_Init_ExtPA_ExtLNA: Init Ext-LNA BBP. [ 15.592000] [7620]:RT6352_Init_ExtPA_ExtLNA: Init Ext-PA MAC. [ 15.604000] [7620]:MCS Set = ff ff 00 00 01 [ 15.616000] [7620]:SYNC - BBP R4 to 20MHz.l [ 18.424000] [7620]:SYNC - BBP R4 to 20MHz.l [ 18.732000] [7620]:SYNC - BBP R4 to 20MHz.l [ 19.040000] [7620]:SYNC - BBP R4 to 20MHz.l [ 19.348000] [7620]:SYNC - BBP R4 to 20MHz.l [ 19.656000] [7620]:SYNC - BBP R4 to 20MHz.l [ 19.964000] [7620]:SYNC - BBP R4 to 20MHz.l [ 20.272000] [7620]:SYNC - BBP R4 to 20MHz.l [ 20.580000] [7620]:SYNC - BBP R4 to 20MHz.l [ 20.888000] [7620]:needFallBack=TRUE due to OP/OT! [ 20.896000] [7620]:needFallBack=TRUE due to OP/OT! [ 20.904000] [7620]:needFallBack=TRUE due to OP/OT! [ 20.916000] [7620]:pAd->CommonCfg.BssCoexApCnt 24! [ 20.928000] [7620]:The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 [ 20.944000] [7620]:Main bssid = 80:3f:5d:b7:58:91 [ 20.952000] <==== rt28xx_init, Status=0 [ 20.964000] 0x1300 = 00064380 [ 20.968000] [7620]:The 7620 UUID MacAddress = 80:3f:5d:b7:58:91 [ 20.972000] [ 20.984000] [7620]:The UUID ASCII string is:28802880-2880-1880-a880-803f5db75891! [ 20.996000] [7620]:The 7620 UUID MacAddress = 80:3f:5d:b7:58:91 [ 21.000000] [ 21.012000] [7620]:The UUID ASCII string is:28802880-2880-1880-a880-803f5db75891! [ 21.056000] build time = [ 21.064000] 20141115060606a [ 21.068000] rom patch for E3 IC [ 21.076000] [ 21.076000] platform = [ 21.084000] ALPS [ 21.088000] hw/sw version = [ 21.092000] Å Å  [ 21.096000] patch version = [ 21.100000]  [ 21.116000] FW Version:0.0.00 Build:1 [ 21.124000] Build Time:201607111443____ [ 21.132000] fw for E3 IC [ 21.152000] RX[0] DESC a26c8000 size = 4096 [ 21.160000] RX[1] DESC a26c9000 size = 4096 [ 21.180000] E2pAccessMode=0 [ 21.188000] cfg_mode=14 [ 21.192000] cfg_mode=14 [ 21.196000] wmode_band_equal(): Band Not Equal! [ 21.216000] APSDCapable[0]=0 [ 21.220000] APSDCapable[1]=0 [ 21.228000] APSDCapable[2]=0 [ 21.232000] APSDCapable[3]=0 [ 21.240000] APSDCapable[4]=0 [ 21.244000] APSDCapable[5]=0 [ 21.252000] APSDCapable[6]=0 [ 21.256000] APSDCapable[7]=0 [ 21.260000] APSDCapable[8]=0 [ 21.268000] APSDCapable[9]=0 [ 21.272000] APSDCapable[10]=0 [ 21.280000] APSDCapable[11]=0 [ 21.284000] APSDCapable[12]=0 [ 21.292000] APSDCapable[13]=0 [ 21.296000] APSDCapable[14]=0 [ 21.304000] APSDCapable[15]=0 [ 21.308000] default ApCliAPSDCapable[0]=0 [ 21.324000] Key1Str is Invalid key length(0) or Type(0) [ 21.336000] Key2Str is Invalid key length(0) or Type(0) [ 21.344000] Key3Str is Invalid key length(0) or Type(0) [ 21.356000] Key4Str is Invalid key length(0) or Type(0) [ 21.388000] HT: 20/40 BssCoexSupport = OFF [ 21.396000] HT: 20/40 BssCoexApCntThr = 0 [ 21.424000] 1. Phy Mode = 49 [ 21.432000] get_chl_grp:illegal channel (167) [ 21.440000] get_chl_grp:illegal channel (167) [ 21.448000] get_chl_grp:illegal channel (169) [ 21.456000] get_chl_grp:illegal channel (169) [ 21.464000] get_chl_grp:illegal channel (171) [ 21.472000] get_chl_grp:illegal channel (171) [ 21.484000] drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed [ 21.504000] Country Region from e2p = ffff [ 21.512000] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 [ 21.528000] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1 [ 21.544000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9 [ 21.560000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 [ 21.580000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 [ 21.596000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 [ 21.612000] mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c [ 21.640000] 2. Phy Mode = 49 [ 21.644000] 3. Phy Mode = 49 [ 21.652000] andes_pci_fw_init [ 21.656000] 0x1300 = 00073200 [ 21.688000] AntCfgInit: primary/secondary ant 0/1 [ 21.696000] andes_load_cr:cr_type(2) [ 21.716000] ChipStructAssign(): MT76x2 hook ! [ 21.724000] @@@ BuildChannel # 36 :: Pwr0 = 28, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 [ 21.724000] @@@ BuildChannel # 40 :: Pwr0 = 28, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 [ 21.744000] @@@ BuildChannel # 44 :: Pwr0 = 28, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 [ 21.760000] @@@ BuildChannel # 48 :: Pwr0 = 28, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 [ 21.776000] @@@ BuildChannel # 52 :: Pwr0 = 23, Pwr1 =23, Flags = c0, RemainingTimeForUse=0 [ 21.792000] @@@ BuildChannel # 56 :: Pwr0 = 23, Pwr1 =23, Flags = c0, RemainingTimeForUse=0 [ 21.812000] @@@ BuildChannel # 60 :: Pwr0 = 23, Pwr1 =23, Flags = c0, RemainingTimeForUse=0 [ 21.828000] @@@ BuildChannel # 64 :: Pwr0 = 23, Pwr1 =23, Flags = c0, RemainingTimeForUse=0 [ 21.844000] @@@ BuildChannel # 100 :: Pwr0 = 19, Pwr1 =25, Flags = c0, RemainingTimeForUse=0 [ 21.860000] @@@ BuildChannel # 104 :: Pwr0 = 19, Pwr1 =25, Flags = c0, RemainingTimeForUse=0 [ 21.876000] @@@ BuildChannel # 108 :: Pwr0 = 19, Pwr1 =25, Flags = c0, RemainingTimeForUse=0 [ 21.896000] @@@ BuildChannel # 112 :: Pwr0 = 19, Pwr1 =25, Flags = c0, RemainingTimeForUse=0 [ 21.912000] @@@ BuildChannel # 116 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 21.928000] @@@ BuildChannel # 120 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 21.948000] @@@ BuildChannel # 124 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 21.964000] @@@ BuildChannel # 128 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 21.980000] @@@ BuildChannel # 132 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 21.996000] @@@ BuildChannel # 136 :: Pwr0 = 22, Pwr1 =28, Flags = c0, RemainingTimeForUse=0 [ 22.016000] @@@ BuildChannel # 140 :: Pwr0 = 22, Pwr1 =28, Flags = 80, RemainingTimeForUse=0 [ 22.032000] @@@ BuildChannel # 149 :: Pwr0 = 21, Pwr1 =24, Flags = c0, RemainingTimeForUse=0 [ 22.048000] @@@ BuildChannel # 153 :: Pwr0 = 21, Pwr1 =24, Flags = c0, RemainingTimeForUse=0 [ 22.064000] @@@ BuildChannel # 157 :: Pwr0 = 21, Pwr1 =24, Flags = c0, RemainingTimeForUse=0 [ 22.084000] @@@ BuildChannel # 161 :: Pwr0 = 21, Pwr1 =24, Flags = c0, RemainingTimeForUse=0 [ 22.100000] @@@ BuildChannel # 165 :: Pwr0 = 21, Pwr1 =24, Flags = 0, RemainingTimeForUse=0 [ 22.116000] MCS Set = ff ff 00 00 01 [ 22.140000] mt76x2_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=42 [ 22.244000] APStartUp(): AP Set CentralFreq at 42(Prim=40, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) [ 22.260000] mt76x2_calibration(channel = 42) [ 22.636000] Main bssid = 80:3f:5d:b7:58:92 [ 22.644000] mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48 [ 22.660000] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48 [ 22.672000] mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33 [ 22.688000] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33 [ 22.700000] original vga value(chain0) = 48 [ 22.708000] original vga value(chain1) = 48 [ 22.716000] <==== rt28xx_init, Status=0 [ 22.724000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii [ 22.740000] RTMPDrvOpen(1):Check if PDMA is idle! [ 22.748000] RTMPDrvOpen(2):Check if PDMA is idle! [ 22.756000] The UUID MacAddress = 80:3f:5d:b7:58:91 [ 22.756000] [ 22.772000] The UUID ASCII string is:28802880-2880-1880-a880-803f5db75891! [ 22.784000] The UUID MacAddress = 80:3f:5d:b7:58:91 [ 22.784000] [ 22.796000] The UUID ASCII string is:28802880-2880-1880-a880-803f5db75891! ifconfig: ioctl 0x8913 failed: No such device brctl: bridge br0: No such device or address ##### configVIF ##### [ 24.540000] FFFFFF80:3F:5D:FFFFFFB7:58:FFFFFF8F [ 24.548000] Raeth v3.1 (Tasklet) [ 24.556000] [ 24.556000] phy_tx_ring = 0x01f98000, tx_ring = 0xa1f98000 [ 24.572000] [ 24.572000] phy_rx_ring0 = 0x01f9a000, rx_ring[0] = 0xa1f9a000 [ 24.588000] [ 24.588000] phy_rx_ring0 = 0x01f9a000, rx_ring[0] = 0xa1f9a000 [ 24.604000] [ 24.604000] Read PhyID ID0:FFFF ID1:FFFF!! [ 24.616000] [ 24.616000] Read PhyID ID0:1C ID1:C916!! [ 24.624000] RTL8211F [ 24.628000] 0x19:863 [ 24.636000] 0x0:1040 [ 24.636000] [ 24.640000] SMACCR1 -- : 0x0000803f [ 24.648000] SMACCR0 -- : 0x5db7588f [ 24.656000] esw_update_led 1 [ 24.656000] ESW: Link Status Changed - Port1 Link UP [ 24.672000] CDMA_CSG_CFG = 81000000 [ 24.680000] GDMA1_FWD_CFG = 20710000 vconfig: ioctl error for rem: No such device vconfig: ioctl error for rem: No such device rmmod: 8021q: No such file or directory [ 24.996000] device eth2 entered promiscuous mode ##### config Ralink ESW vlan partition (LLLLW) ##### switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 Special Tag Disabled switch reg write offset=2610, value=81000000 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10002 switch reg write offset=2514, value=10001 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. [ 29.356000] device ra0 entered promiscuous mode bssid_num = 1 num = 1 [ 29.452000] device eth2.1 entered promiscuous mode [ 29.484000] device rai0 entered promiscuous mode ##### enable 2nd wireless interface ##### udhcpc_lan.pid:/var/run/udhcpc.pid, interface:eth2.2 udhcpc (v1.12.1) started <===>ip:===>subnet:===>router:===>dns:==>domain:> [ 31.444000] br0: port 3(rai0) entering learning state [ 31.456000] br0: port 3(rai0) entering learning state [ 31.464000] br0: port 2(eth2.1) entering learning state [ 31.476000] br0: port 2(eth2.1) entering learning state [ 31.484000] br0: port 1(ra0) entering learning state [ 31.496000] br0: port 1(ra0) entering learning state ifconfig: ioctl 0x8914 failed: Cannot assign requested address ifconfig: ioctl 0x8914 failed: Cannot assign requested address [ 32.456000] br0: port 3(rai0) entering forwarding state [ 32.476000] br0: port 2(eth2.1) entering forwarding state [ 32.496000] br0: port 1(ra0) entering forwarding state killall: udhcpd: no process killed Set: phy[1].reg[[ 34.124000] esw_update_led 1 [ 34.124000] ESW: Link Status Changed - Port1 Link Down 0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Port5 is down. Skip. Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 Set: phy[5].reg[0] = f7ff ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ra2 no private ioctls. ra2 no private ioctls. ifconfig: ioctl 0x8913 failed: No such device Interface doesn't accept private ioctl... set (8BE2): Invalid argument [ 36.248000] Ralink HW NAT Module Enabled [ 36.256000] PpeDevRegHandler : ineterface eth2 register (0) [ 36.268000] PpeSetDstPort :dst_port[0] =eth2 [ 36.288000] PpeDevRegHandler : ineterface ra0 register (1) [ 36.296000] PpeDevRegHandler : ineterface apcli0 register (2) [ 36.320000] PpeDevRegHandler : ineterface rai0 register (3) [ 36.368000] ADDRCONF(NETDEV_UP): apcli0: link is not ready [ 36.380000] ADDRCONF(NETDEV_UP): apclii0: link is not ready /sbin/internet.sh: line 1826: radvd.sh: not found /sbin/internet.sh: line 1915: [CONFIG_USER_WSC: not found /sbin/internet.sh: line 1915: nfchod: not found [ 36.488000] WLINK IGD Filter V1.0 [ 36.496000] LAN IF: br0 [ 36.500000] WAN IF: eth2.2 [ 36.504000] Bridge mode: False [ 36.512000] New domain [2] : wifi.wavlink.com [ 36.520000] New domain [3] : ap.setup [ 36.528000] Domain List [0] ap.setup [ 36.536000] Domain List [1] wifi.wavlink.com [ 36.544000] Domain List [2] wifi.wavlink.com [ 36.552000] Domain List [3] ap.setup [ 36.560000] WLINK IGD: Device lo is up. [ 36.568000] WLINK IGD: Device eth2 is up. [ 36.576000] WLINK IGD: Device ra0 is up. [ 36.584000] WLINK IGD: Device rai0 is up. [ 36.592000] WLINK IGD: Device eth2.1 is up. [ 36.600000] WLINK IGD: Device eth2.2 is up. [ 36.608000] WLINK IGD: Device br0 is up. [ 36.616000] WLINK IGD: LAN Device[br0] = 10aa8c0, 192.168.10.1, 80:3f:5d:b7:58:8f [ 36.632000] WLINK IGD Timer be started. [ 36.960000] esw_update_led 1 [ 36.960000] ESW: Link Status Changed - Port1 Link UP killall: schedule.sh: no process killed <===>ip:===>subnet:===>router:===>dns:==>domain:> wireless.c:restart_wps:1196:[restart_wps]wps_restart.wsc_enable=0 route: ioctl 0x890c failed: No such process sh: miniupnpd.sh: not found killall: rt2860apd: no process killed wireless.c:restart_wps:1196:[restart_wps]wps_restart.wsc_enable=0 route: ioctl 0x890c failed: No such process sh: miniupnpd.sh: not found Jan 1 00:00:41 crond[2016]: crond (busybox 1.12.1) started, log level 8 killall: rtinicapd: no process killed File '/tmp/need_clear_iptables' doesn't exist. iptables: Bad rule (does a matching rule exist in that chain?). File '/tmp/need_clear_iptables' doesn't exist. iptables: No chain/target/match by that name. 1.pool.ntp.org: Unknown host [ 45.832000] led=13, on=4000, off=1, blinks=1, reset=1, time=4000 [ 45.852000] led=12, on=4000, off=1, blinks=1, reset=1, time=4000 [ 45.872000] led=43, on=4000, off=1, blinks=1, reset=1, time=4000 [ 45.896000] led=72, on=4000, off=1, blinks=1, reset=1, time=4000 0 webs: Listening for HTTP requests at address 192.168.10.1 1970-01-01 00:00:48: (log.c.217) server started init_system.c:main:133:----------init_fw.sh-------- linklog: Start linklog file to www utils.c:get_macaddr:662:Util.c init_fw: init_wifi: WAVLINK login:


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/07/03 00:37
  • by ianchi