TP-Link Archer C2300 v1

Wireless-AC router based on BCM4365E & BCM4360 with 128MB flash and 512MB RAM.

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Not supported.

Describe if there are any ongoing activities that might lead to OpenWrt support.

CPU Ram Flash Network WLAN USB Serial JTag
Broadcom BCM4906 @ 1,8 GHz 512 MiB 128 MiB 5x Gbit abgnac 1x 2.0, 1×3.0 ? ?

(source: https://github.com/acc-/tplink-archer-c2300/wiki/Boot-logs by Adam acc-)

---- BTRM V1.6 CPU0 L1CD MMUI MMU7 DATA ZBBS MAIN OTP? OTPP USBT NAND IMG? IMGL UHD? UHDP RLO? RLOP UBI? UBIP PASS ---- HELO 5.0202HNDrc7-1.0.38-161.122 CPU0 L1CD MMUI MMU> CODE ZBBS MAIN NVRAM memcfg 0x1427 MCB chksum 0xa89ec7d9, config 0x1427 MemsysInit lpf0_generic_aarch64 1.3.0.1 20150910 DDR3 900017E8 80018000 8001A000 00000000 00000000 0050371A MCB rev=0x00040301 Ref ID=0x0371A Sub Bld=0x005 Dram Timing 11-11-11 DDR3-1600 CL11 total 512MB 1 16bits part[s] %1 SSC Add/Ctl Alignment no adjustment ZQ Cal LP PHY R in Ohm P: Finger=0x2D0 Term=0x78 Drv=0x2A N: Finger=0x2D0 Term=0x78 Drv=0x2A PLL Ref(Hz)=0x02FAF080 UI STEPS=0x039 DDR CLK(MHz)=0x31B WL CLK dly(ps)=0x0C8 bitT(ps)=0x274 VDLsize(fs)=0x2B09 CLK_VDL=0x01A SHMOO 28nm 8001A000 80018800 00000000 00020000 00000000 Shmoo WL One UI Steps : 0x44 auto-clk result = 00B (filter=0C steps) initial CLK shift = 01A final CLK shift = 00B 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 S----------------X++++++++++++++++++++++++++++++++++++++++++++++++++ 01 S----------------X++++++++++++++++++++++++++++++++++++++++++++++++++ Shmoo RD En FORCED WR ODT = 0x18001800 DQSN DRIVE PAD CONTROL (from) (to) B0 00031A31 00079A31 B1 00031A31 00079A31 B0 RISE UI=1 VDL=17 PICK UI=2 VDL=17 B1 RISE UI=1 VDL=15 PICK UI=2 VDL=15 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 --S--------------------X++++++++++++++++++++++++++++++++++++++++++++ 01 --S------------------X++++++++++++++++++++++++++++++++++++++++++++++ Shmoo RD DQ NP DQS : B0 VDL=39 ok B1 VDL=39 ok 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 --++++++++++++++++++++++++X++++++++++++++++++++++++----------------- 01 -------+++++++++++++++++++++++X+++++++++++++++++++++++-------------- 02 ---++++++++++++++++++++++++X++++++++++++++++++++++++---------------- 03 ---------++++++++++++++++++++++++X++++++++++++++++++++++++---------- 04 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 05 --------++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 06 ---++++++++++++++++++++++++X+++++++++++++++++++++++++--------------- 07 ----------++++++++++++++++++++++++X+++++++++++++++++++++++++-------- 08 -------+++++++++++++++++++++++X++++++++++++++++++++++++------------- 09 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++-------------- 10 --------+++++++++++++++++++++++X+++++++++++++++++++++++------------- 11 ----++++++++++++++++++++++++X+++++++++++++++++++++++++-------------- 12 ---------++++++++++++++++++++++++X++++++++++++++++++++++++---------- 13 ------++++++++++++++++++++++++X++++++++++++++++++++++++------------- 14 -------++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 15 --------++++++++++++++++++++++++X++++++++++++++++++++++++----------- Shmoo RD DQ P 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 +++++++++++++++++++++++++X++++++++++++++++++++++++++---------------- 01 -----++++++++++++++++++++++++X++++++++++++++++++++++++-------------- 02 +++++++++++++++++++++++++X++++++++++++++++++++++++++---------------- 03 ------+++++++++++++++++++++++++X++++++++++++++++++++++++++---------- 04 --++++++++++++++++++++++++++X++++++++++++++++++++++++++------------- 05 ------+++++++++++++++++++++++++X++++++++++++++++++++++++++---------- 06 ++++++++++++++++++++++++++X++++++++++++++++++++++++++--------------- 07 -------++++++++++++++++++++++++++X++++++++++++++++++++++++++-------- 08 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 09 --+++++++++++++++++++++++++X++++++++++++++++++++++++++-------------- 10 ------++++++++++++++++++++++++X++++++++++++++++++++++++------------- 11 --+++++++++++++++++++++++++X++++++++++++++++++++++++++-------------- 12 -----++++++++++++++++++++++++++X++++++++++++++++++++++++++---------- 13 --++++++++++++++++++++++++++X++++++++++++++++++++++++++------------- 14 ----++++++++++++++++++++++++++X++++++++++++++++++++++++++----------- 15 -----+++++++++++++++++++++++++X++++++++++++++++++++++++++----------- Shmoo RD DQ N 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 --++++++++++++++++++++++++X++++++++++++++++++++++++----------------- 01 -------+++++++++++++++++++++++X++++++++++++++++++++++++------------- 02 ---++++++++++++++++++++++++X++++++++++++++++++++++++---------------- 03 ---------++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 04 -----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 05 --------++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 06 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++-------------- 07 ----------++++++++++++++++++++++++X+++++++++++++++++++++++++-------- 08 ------++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 09 ----+++++++++++++++++++++++++X++++++++++++++++++++++++++------------ 10 -------+++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 11 ----++++++++++++++++++++++++++X++++++++++++++++++++++++++----------- 12 ---------++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 13 ------+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 14 -------+++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 15 --------+++++++++++++++++++++++++X+++++++++++++++++++++++++--------- RD DQS adjustments : BL0: Start: 0x39 Final: 0x39 BL1: Start: 0x39 Final: 0x39 Shmoo WR DQ 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 -++++++++++++++++++++++++X++++++++++++++++++++++++------------------ 01 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 02 --++++++++++++++++++++++++X++++++++++++++++++++++++----------------- 03 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 04 --+++++++++++++++++++++++++X++++++++++++++++++++++++++-------------- 05 ------++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 06 -++++++++++++++++++++++++X+++++++++++++++++++++++++----------------- 07 ------++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 08 ----++++++++++++++++++++++++X+++++++++++++++++++++++++-------------- 09 --++++++++++++++++++++++++X+++++++++++++++++++++++++---------------- 10 ------+++++++++++++++++++++++X++++++++++++++++++++++++-------------- 11 -++++++++++++++++++++++++++X++++++++++++++++++++++++++-------------- 12 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 13 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 14 ----+++++++++++++++++++++++++X++++++++++++++++++++++++++------------ 15 ------+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- Shmoo WR DM WR DM 00000000001111111111222222222233333333334444444444555555555566666666 01234567890123456789012345678901234567890123456789012345678901234567 00 -----++++++++++++++++++++++++++X+++++++++++++++++++++++++++--------- 01 --+++++++++++++++++++++++++++X+++++++++++++++++++++++++++----------- DDR test done successfully FPS0 ---- PAR0 J000 JFFS BT00 0008 ---- PAR1 NONE NAN9 ---- TRY0 NAN3 JFS2 RFS1 JFFS JFS2 NAN5 Base: 5.2_02HNDrc7 CFE version 1.0.38-161.122 for BCM94908 (64bit,SP,LE) Build Date: Wed Sep 20 08:36:53 CST 2017 (rock@rock-computer) Copyright (C) 2000-2015 Broadcom Corporation. Boot Strap Register: 0x6fc42 Chip ID: BCM4906_A0, Broadcom B53 Quad Core: 1800MHz Total Memory: 536870912 bytes (512MB) NAND ECC BCH-4, page size 0x800 bytes, spare size used 64 bytes NAND flash device: MXIC MX30LF1G08AA, id 0xc2f1 block 128KB size 131072KB pmc_init:PMC using DQM mode pmc_init:7 0 fe540465 351034b Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host/tftp (f/h/c) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Default host ramdisk file name : Default ramdisk store address : Default DTB file name : Board Id : 94908REF Number of MAC Addresses (1-64) : 11 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-128) KBytes : 48 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Auxillary File System Size Percent: 0 flow memory allocation (MB) : 14 buffer memory allocation (MB) : 32 DHD 0 memory allocation (MB) : 0 DHD 1 memory allocation (MB) : 0 DHD 2 memory allocation (MB) : 0 WLan Feature : 0x00 Partition 1 Size (MB) : 0M Partition 2 Size (MB) : 8M Partition 3 Size (MB) : 0M Partition 4 Size (MB) (Data) : 4M Initalizing switch low level hardware. Software Resetting Switch ... Done. Waiting MAC port Rx/Tx to be enabled by hardware ...Done Disable Switch All MAC port Rx/Tx *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from only image (address 0x00100000, flash offset 0x00100000) ... Decompression LZMA Image OK! Entry at 0x0000000000080000 Starting program at 0x0000000000080000 /memory = 0x20000000 debug.zy dhd param1 value 0xe debug.zy dhd param2 value 0x0 debug.zy dhd param3 value 0x0 Booting Linux on physical CPU 0x0 Linux version 4.1.27 (rock@rock-computer) (gcc version 5.3.0 (Buildroot 2016.02) ) #35 SMP PREEMPT Tue Nov 21 10:30:24 CST 2017 CPU: AArch64 Processor [420f1000] revision 0 Detected VIPT I-cache on CPU0 alternatives: enabling workaround for ARM erratum 845719 PERCPU: Embedded 16 pages/cpu @ffffffc01ffd4000 s25216 r8192 d32128 u65536 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 122112 Kernel command line: console=ttyS0,115200 init=/etc/preinit irqaffinity=0 coherent_pool=1M PID hash table entries: 2048 (order: 2, 16384 bytes) Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Memory: 439988K/495616K available (4879K kernel code, 277K rwdata, 1648K rodata, 228K init, 430K bss, 55628K reserved, 0K cma-reserved) Virtual kernel memory layout: vmalloc : 0xffffff8000000000 - 0xffffffbdffff0000 ( 247 GB) vmemmap : 0xffffffbe00000000 - 0xffffffbfc0000000 ( 7 GB maximum) 0xffffffbe00000000 - 0xffffffbe00700000 ( 7 MB actual) fixed : 0xffffffbffabfd000 - 0xffffffbffac00000 ( 12 KB) PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) memory : 0xffffffc000000000 - 0xffffffc020000000 ( 512 MB) .init : 0xffffffc0006e1000 - 0xffffffc00071a000 ( 228 KB) .text : 0xffffffc000080000 - 0xffffffc0006e0574 ( 6530 KB) .data : 0xffffffc00071b000 - 0xffffffc0007605a0 ( 278 KB) Preemptible hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 NR_IRQS:64 nr_irqs:64 0 Architected cp15 timer(s) running at 50.00MHz (phys). clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb8812736b, max_idle_ns: 440795202655 ns sched_clock: 56 bits at 50MHz, resolution 20ns, wraps every 4398046511100ns BRCM Legacy Drivers' Helper, all legacy drivers' IO memories/interrupts should be remapped here Remapping interrupts... hwirq virq 61 5 64 6 66 7 91 8 92 9 93 10 77 11 78 12 79 13 80 14 81 15 82 16 83 17 84 18 85 19 86 20 88 21 96 22 97 23 98 24 99 25 118 26 119 27 106 28 104 29 105 30 76 31 120 32 110 33 148 34 154 35 155 36 156 37 157 38 158 39 159 40 69 41 Remapping IO memories... phys virt size 00000000ff800000 ffffff8000008000 00003000 00000000ff858000 ffffff8000002000 00001000 00000000ff85a000 ffffff800000c000 00001000 00000000ffe00000 ffffff8000040000 00020000 0000000080002000 ffffff800000e000 00001000 0000000080018000 ffffff8000010000 00004000 0000000080200000 ffffff8000018000 00005000 0000000080280000 ffffff8000016000 00001000 0000000082200000 ffffff8000080000 00100000 0000000080080000 ffffff8000200000 00050000 0000000080008000 ffffff8000020000 00003fff 000000008000c000 ffffff8000028000 00003fff 0000000081060000 ffffff8000030000 00004000 0000000080100000 ffffff8000038000 00002000 0000000080010000 ffffff800001e000 00001000 000000008001d000 ffffff800003c000 00001010 000000008001c000 ffffff8000026000 00000448 console [ttyS0] enabled Calibrating delay loop (skipped), value calculated using timer frequency.. 100.00 BogoMIPS (lpj=500000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes) --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 creating mapping for reserved memory phys 0x0c400000 virt 0xffffffc00c400000 size 0x00e00000 for dhd0 Do not need to create mapping for reserved memory phys 0x0e000000 size 0x02000000 for buffer creating mapping for reserved memory phys 0x0d200000 virt 0xffffffc00d200000 size 0x00e00000 for flow pmc_init:PMC using DQM mode CPU1: Booted secondary processor Detected VIPT I-cache on CPU1 Brought up 2 CPUs SMP: Total of 2 processors activated. CPU: All CPU(s) started at EL2 alternatives: patching kernel code clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns NET: Registered protocol family 16 cpuidle: using governor ladder cpuidle: using governor menu vdso: 2 pages (1 code @ ffffffc000721000, 1 data @ ffffffc000720000) DMA: preallocated 1024 KiB pool for atomic allocations ACPI: Interpreter disabled. SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb bcmhs_spi bcmhs_spi.1: master is unqueued, this is deprecated skbFreeTask created successfully gbpm_do_work scheduled [0;34mBLOG v3.0 Initialized[0m BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 initialized Broadcom GBPM v0.1 initialized Switched to clocksource arch_sys_counter pnp: PnP ACPI: disabled NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 4, 65536 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 futex hash table entries: 512 (order: 3, 32768 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher exFAT: Version 1.2.9 ntfs: driver 2.1.32 [Flags: R/O]. jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered (default) brd: module loaded loop: module loaded nand: Could not find valid ONFI parameter page; aborting nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 nand: Macronix NAND 128MiB 3,3V 8-bit nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 bcm63xx_nand ff801800.nand: Adjust timing_1 to 0x65324458 timing_2 to 0x80040e54 bcm63xx_nand ff801800.nand: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-4 Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 >>>>> For primary mtd partition rootfs, cferam/vmlinux.lz mounted as JFFS2, vmlinux fs mounted as UBIFS <<<<< Secondary mtd partition rootfs_update detected as JFFS2 for cferam/vmlinux source and vmlinux filesystem Creating 9 MTD partitions on "brcmnand.0": 0x000000460000-0x000003a00000 : "rootfs" 0x000003a00000-0x000007300000 : "rootfs_update" 0x000007b00000-0x000007f00000 : "data" 0x000000000000-0x000000100000 : "nvram" 0x000000100000-0x000003a00000 : "image" 0x000003a00000-0x000007300000 : "image_update" 0x000000100000-0x000000460000 : "bootfs" 0x000000000000-0x000008000000 : "dummy2" 0x000007300000-0x000007b00000 : "misc2" PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered i2c /dev entries driver brcmboard registered brcmboard: brcm_board_init entry print_rst_status: Last RESET due to POR reset print_rst_status: RESET reason: 0x00000000 set_ext_irq_info ERROR: Invalid index entry 255 max is 6 ext_irq 255 BP_EXT_INTR_FLAGS_MASK 0x8000e000 BP_EXT_INTR_0 0x0 set_ext_irq_info ERROR: Invalid index entry 255 max is 6 ext_irq 255 BP_EXT_INTR_FLAGS_MASK 0x8000e000 BP_EXT_INTR_0 0x0 set_ext_irq_info ERROR: Invalid index entry 255 max is 6 ext_irq 255 BP_EXT_INTR_FLAGS_MASK 0x8000e000 BP_EXT_INTR_0 0x0 GPIO: Reset Button Polling is enabled on gpio 8017 GPIO: Led Button Polling is enabled on gpio 8012 GPIO: Wifi Button Polling is enabled on gpio 8016 SES: Button Polling is enabled on gpio 8015 SES: LED GPIO 0x400c is enabled DYING GASP IRQ Initialized and Enabled map_hw_timer_interrupt,132: interrupt_id 22 map_hw_timer_interrupt,132: interrupt_id 23 map_hw_timer_interrupt,132: interrupt_id 24 map_hw_timer_interrupt,132: interrupt_id 25 Serial: BCM63XX driver $Revision: 3.00 $ [0;33mMagic SysRq with Auxilliary trigger char enabled (type ^ h for list of supported commands)[0m ttyS0 at MMIO 0xff800640 (irq = 6, base_baud = 921600) is a BCM63XX BPM: tot_mem_size=536870912B (512MB), buf_mem_size <15%> =80530635B (76MB), num of buffers=35951, buf size=2240 Broadcom BPM Module Char Driver v0.1 Registered<3004>[0m PCIe HCD (impl1) bcm963xx-pcie: found core [0] Rev [ 3. 4] bcm963xx-pcie bcm963xx-pcie.0: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0xc0000000-0xcfffffff] pci_bus 0000:00: root bus resource [bus 00-ff] pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22 pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: of_irq_parse_pci() failed with rc=-22 pci 0000:00:00.0: BAR 8: assigned [mem 0xc0000000-0xc0bfffff] pci 0000:00:00.0: BAR 9: assigned [mem 0xc0c00000-0xc0cfffff 64bit pref] pci 0000:01:00.0: BAR 2: assigned [mem 0xc0000000-0xc07fffff 64bit] pci 0000:01:00.0: BAR 4: assigned [mem 0xc0c00000-0xc0cfffff 64bit pref] pci 0000:01:00.0: BAR 0: assigned [mem 0xc0800000-0xc0807fff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0xc0000000-0xc0bfffff] pci 0000:00:00.0: bridge window [mem 0xc0c00000-0xc0cfffff 64bit pref] pcieport 0000:00:00.0: enabling device (0000 -> 0002) pcieport 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 bcm963xx-pcie: found core [1] Rev [ 3. 4] bcm963xx-pcie bcm963xx-pcie.1: PCI host bridge to bus 0001:00 pci_bus 0001:00: root bus resource [mem 0xd0000000-0xdfffffff] pci_bus 0001:00: root bus resource [bus 00-ff] pci 0001:00:00.0: of_irq_parse_pci() failed with rc=-22 pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0001:01:00.0: of_irq_parse_pci() failed with rc=-22 pci 0001:00:00.0: BAR 8: assigned [mem 0xd0000000-0xd00fffff] pci 0001:01:00.0: BAR 0: assigned [mem 0xd0000000-0xd0007fff 64bit] pci 0001:00:00.0: PCI bridge to [bus 01] pci 0001:00:00.0: bridge window [mem 0xd0000000-0xd00fffff] pcieport 0001:00:00.0: enabling device (0000 -> 0002) pcieport 0001:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 pci 0001:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 bcm963xx-pcie: found core [2] Rev [ 3. 4] bcm963xx-pcie: failed to bring up core [2] link GACT probability NOT on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. xt_time: kernel timezone is -0000 Initializing XFRM netlink socket NET: Registered protocol family 10 NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered L2TP core: blog_l2tp_rcv_check l2tp_core: L2TP core driver, V2.0 l2tp_ip: L2TP IP encapsulation support (L2TPv3) l2tp_netlink: L2TP netlink interface l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) 8021q: 802.1Q VLAN Support v1.8 ubi0: attaching mtd0 ubi0: scanning is finished ubi0: attached mtd0 (name "rootfs", size 53 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 429, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 0 ubi0: available PEBs: 0, total reserved PEBs: 429, PEBs reserved for bad PEB handling: 9 ubi0: background thread "ubi_bgt0d" started, PID 362 UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs_ubifs", R/O mode UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 51425280 bytes (49 MiB, 405 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) UBIFS (ubi0:0): reserved for root: 0 bytes (0 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID BA898232-0BAE-4944-879B-1171735B9C1C, small LPT model VFS: Mounted root (ubifs filesystem) readonly on device 0:11. Freeing unused kernel memory: 228K (ffffffc0006e1000 - ffffffc00071a000) mknod: /dev/flash_chrdev: Read-only file system request_module: runaway loop modprobe net-pf-16-proto-31 request_module: runaway loop modprobe net-pf-16-proto-31 request_module: runaway loop modprobe net-pf-16-proto-31 request_module: runaway loop modprobe net-pf-16-proto-31 request_module: runaway loop modprobe net-pf-16-proto-31 request_module: runaway loop modprobe net-pf-16-proto-31 Mounting filesystems... >>>>> Starting mdev <<<<< >>>>> Creating static device nodes <<<<< >>>>> Mounting /data partition <<<<< >>>>> Mounting data partition as JFFS2 <<<<< wlcsm: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Initializing WLCSM Module WLCSM Module loaded successfully *** CHECK: NVRAM file checking... *** *** CHECK: NVRAM file is ok... *** restore done! [TPDATA]: Found misc2 partition on MTD devide 8, attach ubi1: attaching mtd8 it. ubi1: scanning is finished ubi1: attached mtd8 (name "misc2", size 8 MiB) ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi1: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi1: max/mean erase counter: 11/5, WL threshold: 4096, image sequence number: 624428756 ubi1: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 4 ubi1: background thread "ubi_bgt1d" started, PID 805 [TPDATA]: MTD8 attach succ. [TPDATA]: Mounting tp_data UBI volume as UBIFS UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 820 UBIFS (ubi1:0): recovery needed UBIFS (ubi1:0): recovery completed UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "tp_data" UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi1:0): FS size: 5840896 bytes (5 MiB, 46 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) UBIFS (ubi1:0): reserved for root: 275879 bytes (269 KiB) UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 94BF99E9-2A3E-435D-BF34-DEDCCE3CF54E, small LPT model [TPDATA]: Mount tp_data Done. [product-info]: Check product-info... [product-info]: Done >>>>> Creating static device nodes <<<<< FPM will initialize 2 pool[s] and require 32 MB bcm-fpm: FPM with 2 pool(s) bm_base_addr 0xffffffc00e000000, size 33554432, bm_base_addr_phys 0x000000000e000000 fm_base_addr 0xffffffc00d200000, size 14680064, fm_base_addr_phys 0x000000000d200000 Scratch pad is not initialized. RDP Physical address=0x82200000 Virtual address = 0xffffff8000780000 configure_runner: NATC keysize 0x100070 key element size 16 contextsize 0x102000 context element size 64 ++++Runner gso_desc_pool created successfully rdd_init_params.runner_nat_cache_key_ptr=0xffffffc00d900000 FPM_BPM phy_addr 0x82c30000,virt_addr 0xffffff80004de000 RDP PKT memory = 32MB : Max Possible Bufs <16384> of size <2048>; Allocating <15360> bufs; RDP enum <5> brcmchipinfo: brcm_chipinfo_init entry NBUFF v1.0 Initialized [0;36;44mInitialized fcache state[0m [0;36;44mBroadcom Packet Flow Cache Char Driver v4.0 Registered<3002>[0m Created Proc FS /procfs/fcache [0;36;44mBroadcom Packet Flow Cache registered with netdev chain[0m [0;36;44mBroadcom Packet Flow Cache learning via BLOG enabled.[0m [0;35m[FHW] pktDbgLvl[0xffffffbffc2a6588]=0[0m [0;34m[FHW] fhw_construct: [0m [0;36;44mInitialized Fcache HW accelerator layer state[0m flwStatsThread created [0;36;44mConstructed Broadcom Packet Flow Cache v4.0[0m [1m[34mWifi Forwarding Driver is initialized![0m Loading HND Module hnd 281786 0 - Live 0xffffffbffc2ba000 emf 23790 0 - Live 0xffffffbffc30e000 (P) igs 13356 0 - Live 0xffffffbffc318000 (P) Tuxera FAT 12/16/32 driver version 3016.7.20 [Flags: R/W MODULE]. Built against headers 4.1.27 #12 SMP PREEMPT Sat Dec 31 03:53:08 CST 2016 arm64 Running on kernel 4.1.27 #35 SMP PREEMPT Tue Nov 21 10:30:24 CST 2017 aarch64 Tuxera NTFS driver 3016.7.1.2.3 [Flags: R/W MODULE]. Built against headers 4.1.27 #12 SMP PREEMPT Sat Dec 31 03:53:08 CST 2016 arm64 Running on kernel 4.1.27 #35 SMP PREEMPT Tue Nov 21 10:30:24 CST 2017 aarch64 Tuxera HFS+ driver 3016.6.21.3- preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - jffs2 not ready yet; using ramdisk UBIFS error (pid: 1007): cannot open "ubi0:ubi_rootfs_data", error -19random: dd urandom read with 4 bits of entropy available jffs2 not ready yet; using ramdisk - init - Please press Enter to activate this console. tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> PPP MPPE Compression module registered sit: IPv6 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 24 nf_conntrack version 0.5.0 (3439 buckets, 13756 max) l2tp_ppp: PPPoL2TP kernel driver, V2.0 PPTP driver version 0.8.5 ip6_tables: (C) 2000-2006 Netfilter Core Team ctnetlink v0.93: registering with nfnetlink. fuse init (API version 7.23) ------------------------------------------------------------------------------------- reloadprofile() begin reloadprofile() end ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- reloadconfig() begin reloadconfig() end =========== merge new config =============== =========== merge new config end =============== mergeconfigbycountry() begin user has set country mergeconfigbycountry() do nothing end ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- sh: iqos-db-parser: not found ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- openvpn cert does not exist ------------------------------------------------------------------------------------- [reset factory] tp_restore_userconfig_partly_mark = gmtoff= 01:00 GMT-01:00 [switch] WAN ifs: "eth0" [switch] LAN ifs: "eth1 eth2 eth3 eth4" [switch] LAG1 ifs: "lag0_" [switch] LAG1 map: "0x0" [switch] LAG1 num: 0 BCM_RUNNER_ENET: LAG1 0x0, LAG2 0x0 Runner Port#3 (Internal MUX Port#1) connects to Crossbar Port#1 Unused MUX Internal Port#0 connects to Crossbar External Port#0 Cross Bar MUX Config : Internal Port 00 maps to External Port 00 <reg_val : 0x00000000> ubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16 ubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16 ubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16 Cross Bar MUX Config : Internal Port 01 maps to External Port 01 <reg_val : 0x00000004> Broadcom BCM4906_A0 Ethernet Network Device v0.1 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Scratch pad is not initialized. ++++ disabling GSO on logical_port=3 dev=eth0 eth0: <Int sw port: 3> <Logical : 03> MAC : 02:10:18:01:00:01 Chip Physical Port 10, Cross Bar Port 1, PHY_ID <0x0007f00c:0x0c:Internal PHY > eth1: <Ext sw port: 0> <Logical : 08> PHY_ID <0x0007f008:0x08:Internal PHY> MAC:02:10:18:01:00:01 eth2: <Ext sw port: 1> <Logical : 09> PHY_ID <0x0007f009:0x09:Internal PHY> MAC:02:10:18:01:00:01 eth3: <Ext sw port: 2> <Logical : 10> PHY_ID <0x0007f00a:0x0a:Internal PHY> MAC:02:10:18:01:00:01 eth4: <Ext sw port: 3> <Logical : 11> PHY_ID <0x0007f00b:0x0b:Internal PHY> MAC:02:10:18:01:00:01 NOTE: Using Port Grouping for IMP ports : [ 0 --> 4 ] [ 1, 2 --> 5 ] [ 3 --> 8 ] Ethernet Auto Power Down and Sleep: Enabled Cross bar port 1 of Int switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 0; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 1; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 2; Adv capability change : MII=0x01e1, GMII=0x0f00 Ext switch port 3; Adv capability change : MII=0x01e1, GMII=0x0f00 All Port Bit Map: 0x0f08: eth0,eth1,eth2,eth3,eth4 Chip WAN Only Ports 0008, Defined WAN Only Ports 0000, WAN Only Port Result: 0x0008:eth0 Chip WAN Preffered Ports 0000, Defined WAN Preffered Ports 0000, WAN Preffered Port Result: 0x0000: Chip LAN Only Ports 0f00, Defined LAN Only Ports 0000, LAN Only Port Result: 0x0f00:eth1,eth2,eth3,eth4 WAN/LAN Both Capable Ports 0x0000: Creating Enet CPU ring for queue number 1 with 512 packets,Descriptor base=ffffff800025d000, physical=0x1ea0c000 Creating Enet CPU ring for queue number 0 with 512 packets,Descriptor base=ffffff8000261000, physical=0x1ea10000 ===> Activate Deep Green Mode Initialized Runner Unicast Layer Initialized Runner Multicast Layer [0;36;44mBroadcom Packet Flow Cache HW acceleration enabled.[0m Enabled Runner binding to Flow Cache Initialized Runner Protocol Layer (800) Broadcom Runner Blog Driver Char Driver v0.1 Registered <3009> NComm TMS V6.85 Kernel Module loaded. Broadcom 802.1Q VLAN Interface, v0.1 RDPA DS WAN UDP Filter Command Driver Ethernet Auto Power Down and Sleep: Enabled Energy Efficient Ethernet: Enabled IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [switch] Interface eth0 is set to WAN [switch] Interface eth1 tm is set [switch] Interface eth2 tm is set [switch] Interface eth3 tm is set [switch] Interface eth4 tm is set [switch] Interface eth0 tm is set [switch] SETUP switch base settings success! [switch] SETUP vlan settings success! IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready device eth1 entered promiscuous mode device eth2 entered promiscuous mode device eth3 entered promiscuous mode device eth4 entered promiscuous mode =====>>>>> wifi_calibrate_data_check ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ehci-platform: EHCI generic platform driver ohci-platform: OHCI generic platform driver ++++ Powering up USB blocks dhd_module_init in dhd_queue_budget = 256 dhd_sta_threshold = 2048 dhd_if_threshold = 65536 no wifi platform data, skip PCI_PROBE: bus 1, slot 0,vendor 14E4, device 4365(good PCI location) dhdpcie_init: can't find adapter info for this chip pcieh 0000:01:00.0: enabling device (0000 -> 0002) DHD: dongle ram size is set to 1835008(orig 1835008) at 0x200000 dhd:0: fw path:(null) nv path:(null) Creating CPU ring for queue number 7 with 128 packets descriptor=0xffffffbffc251268 Done initializing Ring 7 Base=0xffffff8000258000 End=0xffffff8000258800 calculated entries= 128 RDD Base=0x1ea07000K descriptor=0xffffffbffc251268 RDPA returned tx wakeup reg = <0x82299004>, val = <0x10000000> RDPA returned rx wakeup reg = <0x8229a004>, val = <0x28000000> Scratch pad is not initialized. dhd_runner_attach: Rx Offload - Enabled, Ring Size = 1024 dhd_attach(): thread:dhd_watchdog_thread:101b started dhd_deferred_work_init: work queue initialized Creating CPU ring for queue number 0 with 1024 packets descriptor=0xffffffbffc2b0ce0 Creating CPU ring for queue number 1 with 1024 packets descriptor=0xffffffbffc2b0d10 [1m[34m wfd_bind: Dev eth5 wfd_idx 0 wl_radio_idx 0 Type fkb configured WFD thread wfd0-thrd minQId/maxQId (8/9), status (0) qmask 0x3[0m Instantiating WFD 0 thread dhd:0: fw path:(null) nv path:(null) dhd_bus_download_firmware: firmware path=, nvram path= dhdpcie_ramsize_adj: Enter dhdpcie_ramsize_adj: Adjust dongle RAMSIZE to 0x240000 xhci-hcd xhci-hcd.0: xHCI Host Controller xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0: hcc params 0x0250f17c hci version 0x100 quirks 0x00010010 xhci-hcd xhci-hcd.0: irq 28, io mem 0x8000d000 hub 1-0:1.0: USB hub found hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19) hotplug detected product: 1d6xhci-hcd xhci-hcd.0: xHCI Host Controller xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. b/2/401 hotphub 2-0:1.0: USB hub found lug detected product: 1d6b/2/401 hotplug detectedhub 2-0:1.0: 2 ports detected ehci-platform ehci-platform.0: EHCI Host Controller product: 1d6b/3/401 ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 3 ehci-platform ehci-platform.0: irq 30, io mem 0x8000c300 hotplug detected product: 1d6b/3/401 ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hotplug detected product: 1d6b/2/401 ohci-platform ohci-platform.0: Generic Platform OHCI controller ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 4 ohci-platform ohci-platform.0: irq 29, io mem 0x8000c400 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected dhdpcie_download_code_array: Download, Upload and compare succeeded (4366c0-roml/pcie-ag-splitrx-fdap-mbss-mfp-wnm-osen-wl11k-wl11u-txbf-pktctx-amsdutx-ampduretry-chkd2hdma-proptxstatus-11nprop-obss-dbwsw-ringer-dmaindex16-bgdfs-stamon-hostpmac-murx-splitassoc-dyn160-dhdhdr, 2017.11.21.102111, 2017/11/21 10:21:11). hotplug detected product: 1d6b/1/401 hotplug detected product: 1d6b/1/401 dhdpcie_bus_write_vars: Download, Upload and compare of NVRAM succeeded. usbcore: registered new interface driver usb-storage random: nonblocking pool is initialized PCIe shared addr (0x002bc3fc) read took 196383 usec before dongle is ready DMA RX offset from shared Area 0 dhdpcie_readshared: Dongle advertizes 2 size indices dhdpcie_readshared: Host support DMAing indices: H2D:1 - D2H:1. FW supports it H2D DMA WR INDX : array size 576 = 2 * 266 D2H DMA RD INDX : array size 64 = 2 * 3 D2H DMA WR INDX : array size 64 = 2 * 3 H2D DMA RD INDX : array size 576 = 2 * 266 ring_info_raw: 56 28 53 43 00 f8 63 43 00 0c 66 43 00 20 68 43 00 26 68 43 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00 dhdpcie_readshared: max H2D queues 266 dhd_bus_start: Initializing 266 h2drings dhd_runner_flowmgr_init: bootmem name<dhd0> addr<ffffffc00c400000> size<14680064> Scratch pad is not initialized. Scratch pad is not initialized. Scratch pad is not initialized. Scratch pad is not initialized. dhd_runner_profile_init: N+M profile = 3 01:1024 -1:2048 -1:1024 -1:0512 00:0512 Scratch pad is not initialized. dhd_runner_policy_init: N+M Policy = 0 1 (HW) dhd_bus_cmn_writeshared: 0000: 00 90 23 19 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 80 40 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 4c 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 49 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 44 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 00 c0 14 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 10 14 00 dhd_bus_cmn_writeshared: 0000: 00 c8 45 15 00 00 00 00 dhd_bus_cmn_writeshared: usb cycle succeed 0000: 00 cc 45 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 c0 45 15 00 00 00 00 dhd_bus_cmn_writeshared: 0000: 00 c4 45 15 00 00 00 00 Attach flowrings pool for 264 rings [0;33;40mRunner DHD PCIE: vendor<0x14e4> device<0x4365> bus<1> slot<0>[0m hotplug detected product: 1d6b/2/401 Initial configuration ================================= rx_post_flow_ring_base_addr : ffffffc015408000 tx_post_flow_ring_base_addr : ffffffc00c3c4000 rx_complete_flow_ring_base_addr : ffffffc015440000 tx_complete_flow_ring_base_addr : ffffffc015490000 r2d_wr_arr_base_addr : ffffff8001562000 d2r_rd_arr_base_addr : ffffff8001562402 r2d_rd_arr_base_addr : ffffff8001562c00 d2r_wr_arr_base_addr : ffffff8001562802 tx_post_mgmt_arr_base_addr : ffffff8001563000 tx_post_mgmt_arr_base_phys_addr : 0x1545d000 r2d_wr_arr_base_phys_addr : 0x1545c000 d2r_rd_arr_base_phys_addr : 0x1545c402 r2d_rd_arr_base_phys_addr : 0x1545cc00 d2r_wr_arr_base_phys_addr : 0x1545c802 Doorbell ISR : ffffffbffc81ff00 Doorbell CTX : ffffffc018b1b400 [0;33;40mRunner DHD Offload initialization complete[0m dhd_rx_frame: net device is NOT registered. drop event packet dhd_rx_frame: net device is NOT registered. drop event packet CUR_ETHERADDR : 6 ac 84 c6 2d c0 36 dhd_sync_with_dongle: GET_REVINFO device 0x43cc, vendor 0x14e4, chipnum 0xaa92 Dongle Host Driver, version 1.363.6 (r) Compiled in drivers/net/wireless/bcmdhd on Nov 21 2017 at 10:21:50 wfd_registerdevice Successfully registered dev eth5 ifidx 0 wfd_idx 0 Register interface [eth5] MAC: ac:84:c6:2d:c0:36 dhd_prot_ioctl: status ret value is -4 dhdpcie_chipmatch: Unsupported vendor 14e4 device 4360 dhdpcie_pci_probe: chipmatch failed!! Broadcom PCI Device 0x4906 has allocated with driver pcieport Broadcom PCI Device 0x4906 has allocated with driver pcieport dhd_module_init out CONSOLE: 000000.000 initvars_cis_pci: Not CIS format CONSOLE: 000000.000 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 000000.000 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 000000.000 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 000000.000 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 000000.000 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 000000.000 srom rev:0 CONSOLE: 000000.000 initvars_srom_pci, SROM CRC Error CONSOLE: 000000.000 initvars_srom_pci, Using external nvram CONSOLE: 000000.000 Setting clocks to 800/400/200 CONSOLE: 000000.000 si_set_bb_vcofreq_frac: only work on 4360, 4350 CONSOLE: 000000.000 Enabling D-cache CONSOLE: 026738.568 gic_dist_init max_irq 64 CONSOLE: 026738.569 c_init: Watchdog reset bit set, clearing CONSOLE: 026738.569 CONSOLE: RTE (PCIE-MSG_BUF) 10.10.122.308 (r) on BCM43666 r4 @ 40.0/200.0/800.0MHz CONSOLE: 026738.569 nvram_init: called again without calling nvram_exit() CONSOLE: 026738.569 initvars_cis_pci: Not CIS format CONSOLE: 026738.587 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.602 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.608 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.615 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.617 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.617 srom rev:0 CONSOLE: 026738.617 initvars_srom_pci, SROM CRC Error CONSOLE: 026738.617 initvars_srom_pci, Using external nvram CONSOLE: 026738.617 allocating a max of 511 rxcplid buffers CONSOLE: 026738.617 pciemsgbuf0: Broadcom PCIE MSGBUF driver CONSOLE: 026738.617 nvram_init: called again without calling nvram_exit() CONSOLE: 026738.617 initvars_cis_pci: Not CIS format CONSOLE: 026738.634 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.649 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.656 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.662 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.664 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.664 srom rev:0 CONSOLE: 026738.664 initvars_srom_pci, SROM CRC Error CONSOLE: 026738.664 initvars_srom_pci, Using external nvram CONSOLE: 026738.664 wlc_ucode_download: wl0: Loading non-MU ucode CONSOLE: 026738.665 reclaim section 0: Returned 216 bytes to the heap CONSOLE: 026738.665 initvars_cis_pci: Not CIS format CONSOLE: 026738.682 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.697 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.704 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.711 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.712 sprom_read_pci: buf[0] = 0xffff, returning bad-crc CONSOLE: 026738.713 srom rev:0 CONSOLE: 026738.713 initvars_srom_pci, SROM CRC Error CONSOLE: 026738.713 initvars_srom_pci, Using external nvram CONSOLE: 026738.713 wlc_bmac_attach, deviceid 0x43cc nbands 1 CONSOLE: 026738.719 ipxotp_init: mapping otpbase at 0x18007000 to 0x18007000 CONSOLE: 026738.720 wl0: wlc_bmac_attach: chiprev 4 corerev 65 cccap 0x58400009 maccap 0xf0018705 band 5G, phy_type 11 phy_rev 33 CONSOLE: 026738.720 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 CONSOLE: 026738.720 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 CONSOLE: 026738.721 wl0: wlc_stf_txcore_shmem_write: No clock CONSOLE: 026738.721 wl0: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 512 CONSOLE: 026738.724 wl_eventq_dup_event: wl_eventq not initialized CONSOLE: 026738.724 wl_eventq_dup_event: wl_eventq not initialized CONSOLE: 026738.724 wl0: Broadcom BCM43666 802.11 Wireless Controller 10.10.122.308 (r) CONSOLE: 026738.724 SPLITRX_MODE_2 enabled : tcmsegsize 160 CONSOLE: 026738.724 TCAM: 512 used: 228 exceed:0 CONSOLE: 026738.724 reclaim section 1: Returned 180292 bytes to the heap CONSOLE: 026738.725 ThreadX v5.6 initialized CONSOLE: CONSOLE: 026739.054 wl0: wlc_enable_probe_req: state down, deferring setting of host flags CONSOLE: 026739.054 wl0: wlc_enable_probe_req: state down, deferring setting of host flags Lan Domain: tplinklogin.net Lan Domain: www.tplinklogin.net wl_module_init: passivemode set to 0x0 wl_module_init: txworkq set to 0x0 wl 0001:01:00.0: enabling device (0000 -> 0002) eth6: Broadcom BCM4360 802.11 Wireless Controller 7.14.164.3 (TOB) (r) device eth6 entered promiscuous mode br-lan: port 5(eth6) entered forwarding state br-lan: port 5(eth6) entered forwarding state device wl1.1 entered promiscuous mode br-lan: port 6(wl1.1) entered forwarding state br-lan: port 6(wl1.1) entered forwarding state device eth5 entered promiscuous mode br-lan: port 7(eth5) entered forwarding state ubi1 error: ubi_open_volume: cannot open device 1, volume 0, error -16 br-lan: port 7(eth5) entered forwarding state dhd_prot_ioctl: status ret value is -29 wfd_registerdevice Device already registered for wfd_idx 0 ifidx 0 wfd_registerdevice Successfully registered dev wl0.1 ifidx 0 wfd_idx 0 dhd_prot_ioctl: status ret value is -23 dhd_wmf_igs_broadcast: WMF: send failure IGMP Query send failed Register interface [wl0.1] MAC: ac:84:c6:2d:c0:36 dhd_prot_ioctl: status ret value is -4 dhd_prot_ioctl: status ret value is -13 dhd_prot_ioctl: status ret value is -13 dhd_prot_ioctl: status ret value is -20 dhd_prot_ioctl: status ret value is -2 dhd_prot_ioctl: status ret value is -2 dhd_prot_ioctl: status ret value is -23 dhd_prot_ioctl: status ret value is -23 dhd_prot_ioctl: status ret value is -23 CONSOLE: 026740.432 wl0: wl_open CONSOLE: 026740.433 wlc_ucode_download: wl0: Loading non-MU ucode dhd_set_mac_addr_handler: MACID is overwritten CONSOLE: 026740.434 wl0: CORE INIT : nfifo 32 mu_tx_enab 0 device wl0.1 entered promiscuous mode CONSOLE: 026740.434 wl0: CORE INIT : mode 2 pktclassify 1 rxsplit 0 hdr conve 0 DMA_CT Enabled br-lan: port 8(wl0.1) entered forwarding state br-lan: port 8(wl0.1) entered forwarding state CONSOLE: 026740.449 reclaim section postattach: Returned 103120 bytes to the heap CONSOLE: 026740.450 wl0: wlc_enable_probe_req: state down, deferring setting of host flags CONSOLE: 026740.450 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 CONSOLE: 026740.508 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026740.524 wl0: invalid chanspec 0x1000 CONSOLE: 026740.539 wl0: wlc_ampdu_tx_set: AGG Mode = MAC+AQM txmaxpkts 512 CONSOLE: 026740.550 wl0: wlc_enable_probe_req: state down, deferring setting of host flags CONSOLE: 026740.557 wl0: wl_open CONSOLE: 026740.558 wlc_ucode_download: wl0: Loading MU ucode CONSOLE: 026740.559 wl0: CORE INIT : nfifo 32 mu_tx_enab 1 CONSOLE: 026740.559 wl0: CORE INIT : mode 2 pktclassify 1 rxsplit 0 hdr conve 0 DMA_CT Enabled CONSOLE: 026740.572 wl0: wlc_enable_probe_req: state down, deferring setting of host flags CONSOLE: 026740.572 enable 1: q0 frmcnt 0, wrdcnt 0, q1 frmcnt 0, wrdcnt 0 CONSOLE: 026742.576 bcm_pack_xtlv_entry: no space tlv_buf: requested:28, available:12 ubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16 dhd_prot_flow_ring_delete: Send Flow Delete Req RING ID 258 for peer 01:00:5e:00:00:01 prio 3 ifindex 1 dhd_prot_flow_ring_delete_response_process: Flow Delete Response status = 0 CONSOLE: 026743.501 wl0: link up (wl0) CONSOLE: 026743.503 wl0: link up (wl0.1) CONSOLE: 026743.513 pciedev_send_ltr:Giving up:0x302 monitor task is initialized pid= 7000 =====>>>>> wireless setting is finished usbshare boot start usbshare boot end USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= tfs_stats.c(309)-tfs_stats_set_interval:Set interval:1 failed!tfs_data.c(235)-tfs_data_clean_entries:clean cmd: rm /tmp/tfs//* tfs_stats.c(416)-tfs_stats_init:Delete all stats failed!USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= General shell run! CONSOLE: 026744.730 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026744.730 flow_create : bitmap_size=512 maxitems=512 USB port event happened -- port= USB port event happened -- port= sysctl (7547): drop_caches: 3 USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= tfs_stats.c(344)-tfs_stats_get_all:Get stats failed!tfs_ubus.c(434)-tfs_ubus_timeout_proc:Ubus get stats failed!USB port event happened -- port= USB port event happened -- port= [switch] switch port eth0 <0 3> phymode is set to 0 [switch] SETUP port (0) media-type: 1000 full on! [switch] switch ports is linked up! CONSOLE: 026750.747 flow_create : bitmap_size=512 maxitems=2048 CONSOLE: 026750.748 wl0.0: wlc_send_bar: seq 0x1 tid 0 CONSOLE: 026751.296 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026751.297 wl0.0: wlc_send_bar: seq 0x1 tid 6 br-lan: port 5(eth6) entered forwarding state br-lan: port 6(wl1.1) entered forwarding state br-lan: port 7(eth5) entered forwarding state br-lan: port 8(wl0.1) entered forwarding state CONSOLE: 026755.796 flow_create : bitmap_size=512 maxitems=2048 CONSOLE: 026755.980 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026756.573 wl0.0: wlc_send_bar: seq 0x3 tid 0 CONSOLE: 026756.660 flow_create : bitmap_size=512 maxitems=2048 CONSOLE: 026756.661 wl0.0: wlc_send_bar: seq 0x1 tid 0 CONSOLE: 026756.899 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026756.900 wl0.0: wlc_send_bar: seq 0x1 tid 6 dhd_flow_rings_delete_for_peer: ifindex 0 dhd_prot_flow_ring_delete: Send Flow Delete Req RING ID 68 for peer 40:b3:95:83:ba:49 prio 3 ifindex 0 dhd_prot_flow_ring_delete: Send Flow Delete Req RING ID 196 for peer 40:b3:95:83:ba:49 prio 0 ifindex 0 dhd_prot_flow_ring_delete_response_process: Flow Delete Response status = 0 dhd_prot_flow_ring_delete_response_process: Flow Delete Response status = 0 CONSOLE: 026769.775 wl0: Proxy STA 40:b3:95:83:ba:49 link is already gone !!?? br-lan: received packet on eth5 with own address as source address CONSOLE: 026777.472 flow_create : bitmap_size=512 maxitems=2048 CONSOLE: 026777.473 wl0.0: wlc_send_bar: seq 0x1 tid 0 CONSOLE: 026777.572 wl0: STA 90:61:ae:fa:19:9b selected as MU client at index 0. CONSOLE: 026777.572 wl0: STA 00:08:f0:14:fb:8d selected as MU client at index 1. CONSOLE: 026777.826 flow_create : bitmap_size=512 maxitems=512 CONSOLE: 026777.827 wl0.0: wlc_send_bar: seq 0x1 tid 6 CONSOLE: 026778.228 wl0.0: wlc_send_bar: seq 0x17 tid 0 CONSOLE: 026781.480 wl0.0: wlc_send_bar: seq 0x18 tid 0 dhd_flow_rings_delete_for_peer: ifindex 0 dhd_prot_flow_ring_delete: Send Flow Delete Req RING ID 68 for peer 90:61:ae:fa:19:9b prio 3 ifindex 0 dhd_prot_flow_ring_delete: Send Flow Delete Req RING ID 196 for peer 90:61:ae:fa:19:9b prio 0 ifindex 0 dhd_flow_rings_delete_for_peer: ifindex 0 dhd_prot_flow_ring_delete_response_process: Flow Delete Response status = 0 dhd_prot_flow_ring_delete_response_process: Flow Delete Response status = 0 CONSOLE: 026790.562 wl0: STA 90:61:ae:fa:19:9b removed from MU client set. CONSOLE: 026790.572 wl0: STA 00:08:f0:14:fb:8d removed from MU client set. debug.zy Kernel Send MSG_NETLINK_BRCM_LED_SWITCH_PRESSED To IPF Center. usb 3-1: new high-speed USB device number 2 using ehci-platform usb-storage 3-1:1.0: USB Mass Storage device detected hotplug detected product: 951/1653/1scsi host0: usb-storage 3-1:1.0 00 hotplug detected product: 951/1653/100 USB port event happened -- port= USB port event happened -- port= USB port event happened -- port=1 USB port event happened -- port=1 scsi 0:0:0:0: Direct-Access Kingston DT 100 G2 PMAP PQ: 0 ANSI: 0 CCS sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.01 GB/3.73 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk tntfs info (device sda, pid 10043): ntfs_fill_super(): fail_safe is enabled. tfat: fail_safe is enabled [EXFAT] trying to mount... FAT-fs (sda): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! tntfs info (device sda1, pid 10188): ntfs_fill_super(): fail_safe is enabled. tntfs info (device sda1, pid 10188): load_system_files(): NTFS volume name 'king', version 3.1 (cluster_size 4096, PAGE_SIZE 4096). BusyBox v1.19.4 (2017-09-19 21:34:17 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. MM NM MMMMMMM M M $MMMMM MMMMM MMMMMMMMMMM MMM MMM MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM' MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM MMMMMM MMMMN M MMMMMMMMM MMMM MMMM MMMM M MMMMMMM M M M --------------------------------------------------------------- For those about to rock... (Attitude Adjustment, unknown) --------------------------------------------------------------- root@AC2300:/#

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/02/07 22:48
  • by dsouza