RavPower RP-WD008

U-Boot 1.1.3 (Sep 17 2018 - 18:22:09) version:1.0.5 Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fac000 flash manufacture id: c8, device id 40 17 find flash: GD25Q64B Initialize GPIO as flow. ljd GPIO as flow. *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: 8 MBytes NOR Flash Date:Sep 17 2018 Time:18:22:09 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 575 MHZ #### estimate memory size =64 Mbytes Initialize vs configure module Initialize GPIO as flow. ljd GPIO as flow. Input i key to enter men 0 read spi flash form 0x50000 bootm: bootm 0x80500000 ## Booting image at 80500000 ... Image Name: RAVPower_RP-WD008 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1816276 Bytes = 1.7 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC [ 1.168000] vgaarb: error -19 registering device [ 1.224000] netif_napi_add() called with weight 128 on device eth0 [ 1.236000] PROC INIT OK! [ 1.384000] ---------------------------- [ 1.392000] --------igd inited---------- [ 1.400000] ---------------------------- procd: Console is alive procd: - preinit - Failed to find i2c_drv. Maybe it is a built in module ? Failed to find button_led. Maybe it is a built in module ? pioctl internet 0 pioctl wifi 0 pioctl control 0 pioctl hdderr 0 pioctl 5g 0 pioctl 24g 0 pioctl 5g24g 0 /etc/preinit: line 1: netmsg: not found Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level kmod: ran 1 iterations jffs2 is ready jffs2 is ready switching to overlay procd: - early - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 13.584000] WARNING: Running kernel does not match configured kernel headers the driver was built with! The driver needs to be rebuilt with the correct kernel headers! [IPC:00456]:ipc server success, path:/tmp/ipc_path_disk, sock:3 led.plan1=0,1[ 17.024000] cmd = 7, arg = 1 led.plan1=0,1[ 22.872000] cmd = 6, arg = 0 led.plan1=0,1 led.plan1=0,1 online =0 led.plan1=0,1 procd: - init complete - led.plan1=0,1 online =0 led.plan1=0,1 led.plan1=0,1 led.plan1=0,1 procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash BusyBox v1.22.1 (2018-01-03 11:45:00 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (14.07, r1302) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@FileHub:/# uname -a Linux FileHub 3.10.14+ #630 Tue Oct 30 15:25:45 CST 2018 mips GNU/Linux root@FileHub:/# cat /proc/mtd dev: size erasesize name mtd0: 00800000 00010000 "ALL" mtd1: 00030000 00010000 "Bootloader" mtd2: 00010000 00010000 "Config" mtd3: 00010000 00010000 "Factory" mtd4: 007a0000 00010000 "firmware" mtd5: 005e48ec 00010000 "rootfs" mtd6: 00110000 00010000 "rootfs_data" root@FileHub:/# dmesg [ 0.000000] Linux version 3.10.14+ (zhangwei@localhost.localdomain) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r112) ) #630 Tue Oct 30 15:25:45 CST 2018 [ 0.000000] [ 0.000000] The CPU feqenuce set to 580 MHz [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) [ 0.000000] Software DMA cache coherency [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 804d9ee0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 quiet rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000007 [ 0.000000] Readback ErrCtl register=00000007 [ 0.000000] Memory: 59464k/65536k available (3663k kernel code, 6072k reserved, 1307k data, 212k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] console [ttyS1] enabled [ 0.032000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.032000] Mount-cache hash table entries: 512 [ 0.032000] NET: Registered protocol family 16 [ 0.036000] RALINK_GPIOMODE = 55054414 [ 0.036000] RALINK_GPIOMODE = 55044414 [ 0.136000] ***** Xtal 40MHz ***** [ 0.136000] start PCIe register access [ 0.632000] RALINK_RSTCTRL = 2400000 [ 0.632000] RALINK_CLKCFG1 = fdbfffc0 [ 0.632000] [ 0.632000] *************** MT7628 PCIe RC mode ************* [ 1.132000] PCIE0 no card, disable it(RST&CLK) [ 1.168000] bio: create slab <bio-0> at 0 [ 1.168000] vgaarb: error -19 registering device [ 1.172000] vgaarb: loaded [ 1.172000] SCSI subsystem initialized [ 1.172000] usbcore: registered new interface driver usbfs [ 1.172000] usbcore: registered new interface driver hub [ 1.172000] usbcore: registered new device driver usb [ 1.172000] Switching to clocksource MIPS [ 1.176000] NET: Registered protocol family 2 [ 1.176000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 1.176000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 1.176000] TCP: Hash tables configured (established 512 bind 512) [ 1.176000] TCP: reno registered [ 1.176000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 1.176000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 1.176000] NET: Registered protocol family 1 [ 1.176000] PCI: CLS 0 bytes, default 32 [ 1.176000] MTK/Ralink EHCI/OHCI init. [ 1.176000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.176000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.176000] fuse init (API version 7.22) [ 1.176000] msgmni has been set to 116 [ 1.180000] io scheduler noop registered (default) [ 1.188000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.188000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A [ 1.188000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 1.200000] brd: module loaded [ 1.200000] flash manufacture id: c8, device id 40 17 [ 1.200000] GD25Q64B(c8 40170000) (8192 Kbytes) [ 1.200000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 [ 1.204000] Creating 5 MTD partitions on "raspi": [ 1.204000] 0x000000000000-0x000000800000 : "ALL" [ 1.204000] 0x000000000000-0x000000030000 : "Bootloader" [ 1.204000] 0x000000030000-0x000000040000 : "Config" [ 1.208000] 0x000000040000-0x000000050000 : "Factory" [ 1.208000] 0x000000050000-0x0000007f0000 : "firmware" [ 1.208000] 0x00000020b714-0x0000007f0000 : "rootfs" [ 1.208000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.212000] mtd: partition "rootfs_data" created automatically, ofs=0x6e0000, len=0x110000 [ 1.212000] 0x0000006e0000-0x0000007f0000 : "rootfs_data" [ 1.212000] [file:drivers/char/button_led/vs_pio.c line:1921] will runninng vs_led_operation(). [ 1.212000] vs pio driver started! [ 1.216000] Reset button driver registered [ 1.216000] PPP generic driver version 2.4.2 [ 1.216000] PPP BSD Compression module registered [ 1.216000] PPP Deflate Compression module registered [ 1.216000] NET: Registered protocol family 24 [ 1.220000] [ 1.220000] [ 1.220000] === pAd = c0049000, size = 1219696 === [ 1.220000] [ 1.220000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x [ 1.224000] <-- RTMPAllocAdapterBlock, Status=0 [ 1.224000] RtmpChipOpsHook(492): Not support for HIF_MT yet! [ 1.224000] mt7628_init()--> [ 1.224000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) [ 1.224000] e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888) [ 1.224000] mt_bcn_buf_init(218): Not support for HIF_MT yet! [ 1.224000] <--mt7628_init() [ 1.224000] rdm_major = 251 [ 1.224000] netif_napi_add() called with weight 128 on device eth0 [ 1.236000] GMAC1_MAC_ADRH -- : 0x0000001c [ 1.236000] GMAC1_MAC_ADRL -- : 0xc245c96e [ 1.236000] Ralink APSoC Ethernet Driver Initilization. v3.1 384 rx/tx descriptors allocated, mtu = 1500! [ 1.236000] NAPI enable, Tx Ring = 384, Rx Ring = 384 [ 1.236000] GMAC1_MAC_ADRH -- : 0x0000001c [ 1.236000] GMAC1_MAC_ADRL -- : 0xc245c96e [ 1.236000] PROC INIT OK! [ 1.244000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.244000] ehci-pci: EHCI PCI platform driver [ 1.244000] ehci-platform: EHCI generic platform driver [ 1.264000] ******MT7628 mtk phy [ 1.264000] *****run project phy. [ 1.272000] FM_OUT value: u4FmOut = 0(0x00000000) [ 1.280000] FM_OUT value: u4FmOut = 128(0x00000080) [ 1.280000] FM detection done! loop = 1 [ 1.288000] SR calibration value u1SrCalVal = 6 [ 1.288000] *********Execute mt7628_phy_init!! [ 1.288000] ehci-platform ehci-platform: EHCI Host Controller [ 1.288000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 1.288000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000 [ 1.300000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 1.300000] hub 1-0:1.0: USB hub found [ 1.300000] hub 1-0:1.0: 1 port detected [ 1.300000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.320000] *********Execute mt7628_phy_init!! [ 1.320000] ohci-platform ohci-platform: Generic Platform OHCI Controller [ 1.320000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 1.320000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000 [ 1.380000] hub 2-0:1.0: USB hub found [ 1.380000] hub 2-0:1.0: 1 port detected [ 1.380000] usbcore: registered new interface driver cdc_acm [ 1.380000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.380000] usbcore: registered new interface driver usb-storage [ 1.380000] u32 classifier [ 1.380000] nf_conntrack version 0.5.0 (929 buckets, 3716 max) [ 1.380000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.380000] Type=Linux [ 1.384000] ---------------------------- [ 1.392000] --------igd inited---------- [ 1.400000] ---------------------------- [ 1.408000] TCP: cubic registered [ 1.408000] NET: Registered protocol family 17 [ 1.408000] 8021q: 802.1Q VLAN Support v1.8 [ 1.408000] registered taskstats version 1 [ 1.412000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.416000] Freeing unused kernel memory: 212K (804db000 - 80510000) [ 3.744000] Raeth v3.1 (NAPI [ 3.744000] ,SkbRecycle) [ 3.748000] [ 3.748000] phy_tx_ring = 0x035aa000, tx_ring = 0xa35aa000 [ 3.748000] [ 3.748000] phy_rx_ring0 = 0x035ac000, rx_ring0 = 0xa35ac000 [ 3.764000] GMAC1_MAC_ADRH -- : 0x0000001c [ 3.764000] GMAC1_MAC_ADRL -- : 0xc245c96e [ 3.764000] RT305x_ESW: Link Status Changed [ 7.340000] jffs2: notice: (318) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 9 of xref (0 dead, 3 orphan) found. [ 7.388000] jffs2: notice: (315) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 9 of xref (0 dead, 3 orphan) found. [ 7.404000] ra2880stop()...Done [ 7.404000] Free TX/RX Ring Memory! [ 13.416000] tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel. [ 13.416000] Disabling lock debugging due to kernel taint [ 13.432000] Tuxera NTFS driver 3015.1.29 [Flags: R/W MODULE]. [ 13.584000] Tuxera FAT 12/16/32 driver version 3015.1.29 [Flags: R/W MODULE]. [ 13.584000] Built against headers 3.10.14+ #404 Tue Jan 17 19:02:33 CST 2017 mips [ 13.584000] Running on kernel 3.10.14+ #630 Tue Oct 30 15:25:45 CST 2018 mips [ 13.584000] WARNING: Running kernel does not match configured kernel headers the driver was built with! The driver needs to be rebuilt with the correct kernel headers! [ 13.808000] Tuxera exFAT driver version 3015.8.24 [Flags: R/W MODULE]. [ 13.808000] Built against headers 3.10.14+ #404 Tue Jan 17 19:02:33 CST 2017 mips [ 13.808000] Running on kernel 3.10.14+ #630 Tue Oct 30 15:25:45 CST 2018 mips [ 13.900000] Tuxera HFS+ driver 3014.7.28 [ 16.112000] Raeth v3.1 (NAPI [ 16.112000] ,SkbRecycle) [ 16.116000] [ 16.116000] phy_tx_ring = 0x037f2000, tx_ring = 0xa37f2000 [ 16.116000] [ 16.116000] phy_rx_ring0 = 0x037f4000, rx_ring0 = 0xa37f4000 [ 16.128000] GMAC1_MAC_ADRH -- : 0x0000001c [ 16.128000] GMAC1_MAC_ADRL -- : 0xc245c96e [ 16.128000] RT305x_ESW: Link Status Changed [ 16.252000] device eth0.1 entered promiscuous mode [ 16.252000] device eth0 entered promiscuous mode [ 16.252000] -------->fdb_create, 470!!! [ 16.252000] nl socket is null ! [ 16.256000] br-lan: port 1(eth0.1) entered forwarding state [ 16.256000] br-lan: port 1(eth0.1) entered forwarding state [ 17.024000] cmd = 7, arg = 1 [ 17.536000] TX_BCN DESC a3e9d000 size = 320 [ 17.536000] RX[0] DESC a3ea0000 size = 512 [ 17.536000] RX[1] DESC a3ea1000 size = 512 [ 17.544000] E2pAccessMode=0 [ 17.544000] cfg_mode=9 [ 17.544000] cfg_mode=9 [ 17.544000] wmode_band_equal(): Band Equal! [ 17.544000] AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD [ 17.548000] APSDCapable[0]=0 [ 17.548000] APSDCapable[1]=0 [ 17.548000] APSDCapable[2]=0 [ 17.548000] APSDCapable[3]=0 [ 17.548000] APSDCapable[4]=0 [ 17.548000] APSDCapable[5]=0 [ 17.548000] APSDCapable[6]=0 [ 17.548000] APSDCapable[7]=0 [ 17.548000] APSDCapable[8]=0 [ 17.548000] APSDCapable[9]=0 [ 17.548000] APSDCapable[10]=0 [ 17.548000] APSDCapable[11]=0 [ 17.548000] APSDCapable[12]=0 [ 17.548000] APSDCapable[13]=0 [ 17.548000] APSDCapable[14]=0 [ 17.548000] APSDCapable[15]=0 [ 17.548000] default ApCliAPSDCapable[0]=0 [ 17.548000] default ApCliAPSDCapable[1]=0 [ 17.744000] Key1Str is Invalid key length(0) or Type(0) [ 17.744000] Key2Str is Invalid key length(0) or Type(0) [ 17.744000] Key3Str is Invalid key length(0) or Type(0) [ 17.744000] Key4Str is Invalid key length(0) or Type(0) [ 17.792000] RTMPSetDefaultChannel() : default channel to 1 [ 17.792000] load fw image from fw_header_image [ 17.792000] AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888) [ 17.792000] FW Version:20151201 [ 17.792000] FW Build Date:20151201183641 [ 17.792000] CmdAddressLenReq:(ret = 0) [ 17.792000] CmdFwStartReq: override = 1, address = 1048576 [ 17.792000] CmdStartDLRsp: WiFI FW Download Success [ 17.796000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) [ 17.796000] efuse_probe: efuse = 10000012 [ 17.796000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4 [ 17.796000] RtmpEepromGetDefault::e2p_dafault=2 [ 17.796000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 [ 17.796000] NVM is FLASH mode [ 17.796000] 1. Phy Mode = 14 [ 17.964000] Country Region from e2p = ffff [ 17.964000] tssi_1_target_pwr_g_band = 30 [ 17.964000] 2. Phy Mode = 14 [ 17.964000] 3. Phy Mode = 14 [ 17.964000] NICInitPwrPinCfg(11): Not support for HIF_MT yet! [ 17.964000] NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet! [ 17.964000] mt_mac_init()--> [ 17.964000] MtAsicInitMac()--> [ 17.964000] mt7628_init_mac_cr()--> [ 17.964000] MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024! [ 17.964000] <--mt_mac_init() [ 17.964000] WTBL Segment 1 info: [ 17.964000] MemBaseAddr/FID:0x28000/0 [ 17.964000] EntrySize/Cnt:32/128 [ 17.964000] WTBL Segment 2 info: [ 17.964000] MemBaseAddr/FID:0x40000/0 [ 17.964000] EntrySize/Cnt:64/128 [ 17.964000] WTBL Segment 3 info: [ 17.964000] MemBaseAddr/FID:0x42000/64 [ 17.964000] EntrySize/Cnt:64/128 [ 17.964000] WTBL Segment 4 info: [ 17.964000] MemBaseAddr/FID:0x44000/128 [ 17.964000] EntrySize/Cnt:32/128 [ 17.968000] AntCfgInit(3026): Not support for HIF_MT yet! [ 17.968000] MCS Set = ff ff 00 00 01 [ 17.968000] MtAsicSetChBusyStat(861): Not support for HIF_MT yet! [ 18.536000] CmdSlotTimeSet:(ret = 0) [ 20.256000] MtAsicSetRalinkBurstMode(3055): Not support for HIF_MT yet! [ 20.256000] MtAsicSetPiggyBack(796): Not support for HIF_MT yet! [ 20.280000] reload DPD from flash , 0x9F = [c600] doReload bit7[0] [ 20.280000] CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0 [ 20.280000] MtAsicSetTxPreamble(3034): Not support for HIF_MT yet! [ 20.284000] MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet! [ 20.284000] The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4 [ 20.284000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 [ 20.284000] Main bssid = 00:1c:c2:45:c9:6e [ 20.284000] <==== rt28xx_init, Status=0 [ 20.292000] @@@ ed_monitor_exit : ===> [ 20.292000] @@@ ed_monitor_exit : <=== [ 20.292000] mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f [ 20.292000] WiFi Startup Cost (ra0): 2.756s [ 20.400000] AddTxSType: already registered TxSType (PID = 32, Format = 0 [ 20.400000] The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4 [ 20.504000] device ra0 entered promiscuous mode [ 20.504000] br-lan: port 2(ra0) entered forwarding state [ 20.504000] br-lan: port 2(ra0) entered forwarding state [ 20.688000] The Access Control List is empty! [ 20.688000] No need to clear the Access Control List! [ 22.872000] cmd = 6, arg = 0 [ 24.092000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. [ 31.264000] br-lan: port 1(eth0.1) entered forwarding state [ 35.552000] br-lan: port 2(ra0) entered forwarding state root@FileHub:/#

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING