AVM FRITZ!Repeater 2400
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
OpenWrt support
Not supported.
Hardware highlights
SOC | CPU | Ram | Flash | Network | WLAN | USB | Serial | JTag |
---|---|---|---|---|---|---|---|---|
QCN5502 | MIPS 74Kc @ 775 MHz | ? MiB | ? MiB | 1x 1 GB | bgn | None | Yes | ? |
Hardware
Info
Architecture | MIPS 74Kc |
---|---|
Vendor | AVM |
Bootloader | U-Boot |
System-On-Chip | QCN5502 |
CPU/Speed | 775 MHz |
Flash-Chip | Macronix MX25L51245GZ2I-10G |
Flash size | 512 MiB |
RAM | ? |
Wireless | QCA9984 MU-MIMO 4 × 4 Wave-2 802.11 ac |
Ethernet | 1 Gbit/s (Atheros AR8033-AL1A) |
Switch | ? |
USB | No |
Serial | Yes |
JTAG | Not populated |
Photos
Insert photo of front of the casing
Insert photo of back of the casing
Insert photo of backside label
Insert photo of PCB
Opening the case
Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port
Replace EXAMPLE by real values.
Serial connection parameters for AVM FRITZ!Repeater 2400 @@Version@@ | EXAMPLE 115200, 8N1, 3.3V |
---|
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port
Bootlogs
OEM bootlog
(AVM) EVA Revision: 1.10293 (C) Copyright 2018 AVM Date: Mar 22 2019 Time: 19:09:14 (0) 3 0x0-0x240D
[FLASH:] MACRONIX Uniform-Flash 64MB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 1024 sectors a 64kB) [SYSTEM:] QCA956x on 775/650/258MHz
Eva_AVM >.................................................ExecuteProgram [ 0.000000] Linux version 4.4.60 (jenkins@jenkins-ci.avm.de) (gcc version 5.5.0 (Buildroot 2018.11.4-g09a6ebd653) ) #1 2021-04-08 [ 0.000000] DT @ 8071f030: d0 0d fe ed 00 00 1d d6 [ 0.000000] MIPS: machine is AVM FRITZ!Repeater 2400 [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc) [ 0.000000] Set Port base [ 0.000000] detect_sys_type [ 0.000000] SoC: Qualcomm Atheros QCA5502 ver 1 rev 0 [ 0.000000] [plat_mem_setup] memsize 0x8000000, memstart 0x00000000 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] [fw-info] Version 07.27 [ 0.000000] [module-mem] Use 0x01107000-0x015bbfff (mapped at 81107000-815bbfff) for 30 modules [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: gocommand console=ttyS0,115200n8r nor_size=0 sflash_size=64MB nand_size=0MB ethaddr=3C:A6:2F:1F:CF:95 slub_debug=- [ 0.000000] setup_slub_debug: slub_debug = [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] [mips_nmi_setup] setup NMI vector to base 0x80000380 [ 0.000000] Memory: 116384K/131072K available (4678K kernel code, 570K rwdata, 1712K rodata, 284K init, 971K bss, 14688K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] [nmi] VA:PA c0000000:40000000 wired at entry 0x1 [ 0.000000] NR_IRQS:91 [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns [ 0.000006] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns [ 0.225945] console [ttyS0] enabled [ 0.229568] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048) [ 0.264213] pid_max: default: 32768 minimum: 301 [ 0.269037] Security Framework initialized [ 0.273202] AppArmor: AppArmor initialized [ 0.277420] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.284209] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.292386] Performance counters: mips/74K PMU enabled, 4 32-bit counters available to each CPU, irq 21 [ 0.304807] devtmpfs: initialized [ 0.311246] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.321267] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.328299] NET: Registered protocol family 16 [ 0.333381] console [avm0] enabled [ 0.337139] cpuidle: using governor ladder [ 0.341314] cpuidle: using governor menu [ 0.345341] Creating Config Table [ 0.348900] Enabling UART-Input for Pin 18 [ 0.355750] MIPS: machine is AVM FritzRepeater 2400 [ 0.360783] [avm_pmu] Set reg 18116cc4 to 0x00300000 [ 0.367147] avm_check_cpu_features: mips-options: 0x40006d638b icache.flags 0x00000000 dcache.flags 0x00000004 isa_level 0x00000031 ases 00000051 [ 0.380781] avm_alloc_page_extension node_extension_table[0] entries=32768 (size=131072) alloced [ 0.389914] Reboot Status is: Power-On [ 0.393947] no support for hwid 241 [ 0.397481] [avmnet] [avmnet_cfg_init] initializing [ 0.402856] pstore: Registered ramoops as persistent store backend [ 0.409191] ramoops: attached 0x80000@0xf80000, ecc: 0/0 [ 0.414920] [find_nmi_vector] no nmi vector found [ 0.423932] SCSI subsystem initialized [ 0.427958] usbcore: registered new interface driver usbfs [ 0.433617] usbcore: registered new interface driver hub [ 0.439076] usbcore: registered new device driver usb [ 0.743184] registering PCI controller with io_map_base unset [ 0.749187] PCI host bridge to bus 0000:00 [ 0.753354] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff] [ 0.760414] pci_bus 0000:00: root bus resource [io 0x0001] [ 0.766148] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.773139] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.781773] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.789285] pci 0000:00:00.0: using irq 80 for pin 1 [ 0.794927] AVM PA for Linux version 4.4.60 (jenkins@jenkins-ci.avm.de) (gcc version 5.5.0 (Buildroot 2018.11.4-g09a6ebd653) ) #1 2021-04-08 [ 0.794927] (early init) [ 0.811010] clocksource: Switched to clocksource MIPS [ 0.816621] AppArmor: AppArmor Filesystem Enabled [ 0.823413] NET: Registered protocol family 2 [ 0.828488] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.835652] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.842156] TCP: Hash tables configured (established 1024 bind 1024) [ 0.848773] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.854766] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.861444] avm_pa: try to activate hw accelaration for pid 1 (ipv4) called from avm_pa_dev_pidhandle_register_with_ingress [ 0.872940] NET: Registered protocol family 1 [ 0.878355] audit: initializing netlink subsys (disabled) [ 0.883970] audit: type=2000 audit(0.556:1): initialized [ 0.898619] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.904958] ANTFS Module: Version 2.46 [ 0.908919] fuse init (API version 7.23) [ 0.914501] io scheduler noop registered [ 0.918531] io scheduler deadline registered (default) [ 0.928423] ttyS0 at MMIO 0x18020000 (irq = 19, base_baud = 1562500) is a PORT_16550A [ 0.937113] [loadcontrol] set auto - scale=1 [ 0.941509] [avm] configured: watchdog event debug [ 0.946455] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0) [ 0.953543] [ath:watchdog] activate nmi-mode [ 0.958120] Register push button event to receive the set_factory_kernel event [ 0.966614] AVM Simple Profiling enabled Version 3.0 [ 0.971711] [simple-profiling]:4 performance counters implemented, OLD_34K [ 0.979297] avm_net_trace: Up and running. [ 0.983846] ath79_spi_fixup_mac_addr: No eth0 node in DT (-1) [ 0.989729] ath79_spi_fixup_mac_addr: Set local-mac-address failed for eth0 (-4) [ 0.997374] ath79_spi_fixup_mac_addr: No eth1 node in DT (-1) [ 1.003231] ath79_spi_fixup_mac_addr: Set local-mac-address failed for eth1 (-4) [ 1.011782] Registering ATH-flash-driver... [ 1.016108] [ath_flash] Use 4 byte addressing [ 1.051609] 6 avm_squashfs partitions found on MTD device ath-nor [ 1.057832] [TFFS3_Register_Panic_CB] registering panic callback for mtd ath-nor [ 1.065446] Creating 6 MTD partitions on “ath-nor”: [ 1.070473] 0x0000022d2e00-0x000004000000 : “rootfs” [ 1.076717] [rootfs] use mtd0 (rootfs) as root [ 1.081298] mtdsplit: no squashfs found in “rootfs” [ 1.086267] 0x000002090000-0x0000022d2e00 : “kernel” [ 1.092402] 0x000000000000-0x000000020000 : “urlader” [ 1.098615] 0x000000020000-0x000000090000 : “tffs (1)” [ 1.104976] 0x000002020000-0x000002090000 : “tffs (2)” [ 1.111381] 0x000000090000-0x000002000000 : “reserved-kernel” [ 1.118383] tun: Universal TUN/TAP device driver, 1.6 [ 1.123565] tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com [ 1.130108] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.136815] ehci-pci: EHCI PCI platform driver [ 1.141609] usbcore: registered new interface driver usblp [ 1.147289] usbcore: registered new interface driver usb-storage [ 1.153424] i2c /dev entries driver [ 1.157293] AVM PA for Linux Linux version 4.4.60 (jenkins@jenkins-ci.avm.de) (gcc version 5.5.0 (Buildroot 2018.11.4-g09a6ebd653) ) #1 2021-04-08 [ 1.157293] (late init) [ 1.173979] gre: GRE over IPv4 demultiplexor driver [ 1.179712] NET: Registered protocol family 10 [ 1.185304] avm_pa: try to activate hw accelaration for pid 2 (ipv6) called from avm_pa_dev_pidhandle_register_with_ingress [ 1.196852] NET: Registered protocol family 17 [ 1.201437] Bridge broadcast ratelimiter registered [ 1.206410] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.219444] Bridge firewalling registered [ 1.223559] l2tp_core: L2TP core driver, V2.0 [ 1.228001] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.233791] l2tp_netlink: L2TP netlink interface [ 1.238538] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.244587] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.251426] 8021q: 802.1Q VLAN Support v1.8 [ 1.255869] [nmi] copy_nmi_trampoline done [ 1.261315] [TFFS3_Init] Called. [ 1.264614] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.271925] [TFFS3_CACHE_Configure] Setting up caching for backend legacy [ 1.278908] [TFFS3-CACHE] Caching module for TFFS 3.x [ 1.284112] [TFFS3_LGCY_Setup] using mtd3(tffs (1)), mtd4(tffs (2)) [ 1.290566] [TFFS3_LGCY_Setup] mtd “tffs (1)”: segment value 18 [ 1.296657] [TFFS3_LGCY_Setup] mtd “tffs (2)”: segment value 19 [ 1.302745] [TFFS3_LGCY_Setup] Using segment 19 (avail: 18 + 19) [ 1.308925] [TFFS3_LGCY_Setup] mtd4 size=0x70000 [ 1.314399] TFFS: tiny flash file system driver. GPL © AVM Berlin (Version 3.0) [ 1.322097] Adam2 environment variables API installed. [ 1.331357] [avm_fair_share] change trip level 0 → -1 for temp 36000 [ 1.338122] lm75 0-0048: hwmon0: sensor 'lm75' [ 1.346381] i2c-gpio i2c@0: using pins 16 (SDA) and 17 (SCL) [ 1.352559] {avmnet_cfg_netinit} [ 1.355865] [avmnet] No config found for HWRev 241, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev [ 1.366042] [avmnet] No config found for HWRev 241, HWSubRev 1, trying base config for HWRev [ 2.789046] [avmnet] [avmnet_ar8033_powerdown] Called for module ar8033 [ 2.795870] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 3c:a6:2f:1f:cf:95 [ 2.811085] VFS: Mounted root (squashfs filesystem) readonly on device 31:0. [ 2.821860] devtmpfs: mounted [ 2.826410] Freeing unused kernel memory: 284K (80739000 - 80780000) starting pid 42, tty '/dev/ttyS0': '/etc/boot.d/1' [ 3.693390] [module-mem] give 0x27000 bytes at 81108000 to module 'hui' (0x48d000 bytes left) [ 3.706596] [hui] Initialize hardware user interface [ 3.713076] [avm_connect][state_machine_init] starting event worker thread [ 3.720524] avm,hui-generic-led-avm avm-hui:repeater-one-no-rssi: Using avm-gpios <106, 105, 107> [ 3.729763] avm,hui-generic-led-avm avm-hui:rssi1: Using avm-gpios <100, 0, 0> [ 3.737256] avm,hui-generic-led-avm avm-hui:rssi2: Using avm-gpios <101, 0, 0> [ 3.744756] avm,hui-generic-led-avm avm-hui:rssi3: Using avm-gpios <102, 0, 0> [ 3.752269] avm,hui-generic-led-avm avm-hui:rssi4: Using avm-gpios <103, 0, 0> [ 3.759778] avm,hui-generic-led-avm avm-hui:rssi5: Using avm-gpios <104, 0, 0> [ 3.767441] avm,hui-generic-button-avm avm-hui:repeater-connect: Using avm-gpios <1> [ 3.822597] [TFFS_Cache] Allocate segement buffer cache (size=32784) [ 3.829633] TFFS Name Table N [Supervisor] Warning: capi.service: could not resolve dependency piglet.service [Supervisor] Warning: kpid.service: could not resolve dependency psetd.service [Supervisor] Warning: ptest_release.service: could not resolve dependency voip.service [Supervisor] Warning: udevadm.service: could not resolve dependency piglet.service [Supervisor] Info: start disable_ipv6.service [Supervisor] Info: start tffs.service [Supervisor] Info: disable_ipv6.service exit success Jan 1 00:00:04 ar7cfgctl[121]: load_config(ar7): open problem - factory default Please press Enter to activate this console. Jan 1 00:00:04 ar7cfgctl[130]: load_config(ar7): open problem - factory default loaded [Supervisor] Info: tffs.service exit success [Supervisor] Info: start rekey.service firmwarecfg config_rekey: nop [Supervisor] Info: rekey.service exit success [Supervisor] Info: start environment.service [Supervisor] Info: environment.service exit success [Supervisor] Info: start flash-update.service [Supervisor] Info: flash-update.service exit success [Supervisor] Info: start oemcheck.service [Supervisor] Error: could not start: /etc/boot.d/core/oemcheck [Supervisor] execvp returned: No such file or directory [Super[ 6.592044] AVM_WATCHDOG: System Init Ueberwachung 120 Sekunden visor] Info: oemcheck.service exit error [Supervisor] Info: start watchdog.service [Supervisor] Info: watchdog.service exit success [Supervisor] Info: start capi-config.service [Supervisor] Info: start udev.service [Supervisor] Info: start udevadm.service [Supervisor] Info: capi-config.service exit success [Supervisor] Info: start capi.service [Supervisor] Info: capi.service exit success [ 7.021911] udevd[255]: starting version 3.2.5 [ 7.117067] udevd[255]: specified group 'tty' unknown [ 7.127410] udevd[255]: specified group 'dialout' unknown [ 7.135682] udevd[255]: specified group 'kmem' unknown [ 7.141148] udevd[255]: specified group 'input' unknown [ 7.146705] udevd[255]: specified group 'video' unknown [ 7.152322] udevd[255]: specified group 'audio' unknown [ 7.158009] udevd[255]: specified group 'lp' unknown [ 7.163365] udevd[255]: specified group 'disk' unknown [ 7.168816] udevd[255]: specified group 'cdrom' unknown [ 7.174445] udevd[255]: specified group 'tape' unknown [ 7.182312] udevd[255]: starting eudev-3.2.5 [Supervisor] Info: udevadm.service exit success [Supervisor] Info: start modules-load.service modprobe: module kdsldmod not found in modules.dep [ERROR] Failed to load kernel module kdsldmod [ 7.586458] cprocfsmod: module license 'unspecified' taints kernel. [ 7.592884] Disabling lock debugging due to kernel taint [ 7.598483] [module-mem] give 0x3000 bytes at 8112f000 to module 'cprocfsmod' (0x48a000 bytes left) [ 7.610741] [module-mem] give 0x5000 bytes at 81132000 to module 'cchardev' (0x485000 bytes left) [ 7.620783] cchardevice: loaded [ 7.737805] [module-mem] give 0x49000 bytes at 81137000 to module 'krextdmod' (0x43c000 bytes left) [ 7.755433] krextd: Initialisation of debughandles ... [ 7.760679] krextd: Initialisation of debughandles [OK] [ 7.766039] krextd: Initialisation of procfs ... [ 7.770809] krextd: Initialisation of procfs [OK] [ 7.775631] krextd: Initialisation of kmod_debugctl ... [ 7.781015] krextd: Initialisation of kmod_debugctl [OK] [ 7.786471] krextd: Initialisation of cenv ... [ 7.791039] krextd: Initialisation of cenv [OK] [ 7.795697] krextd: Initialisation of ctimer ... [ 7.800628] krextd: Initialisation of ctimer [OK] [ 7.805425] krextd: Initialisation of kmodcmddev ... [ 7.810533] krextd: Initialisation of kmodcmddev [OK] [ 7.815727] krextd: Initialisation of packettrace ... [ 7.820935] krextd: Initialisation of packettrace [OK] [ 7.826209] krextd: Initialisation of nqos ... [ 7.836408] krextd: Initialisation of nqos [OK] [ 7.841056] krextd: Initialisation of bridgeflt ... [ 7.846054] krextd: Initialisation of bridgeflt [OK] [ 7.851148] krextd: Initialisation of timer ... [ 7.855803] krextd: Initialisation of timer [OK] [ 7.860553] krextd: Initialisation of krextd ... [ 7.865300] krextd: Initialisation of krextd:debughandles ... [ 7.871232] krextd: Initialisation of krextd:debughandles [OK] [ 7.877216] krextd: Initialisation of krextd:global ... [ 7.882612] krextd: Initialisation of krextd:global [OK] [ 7.888059] krextd: Initialisation of krextd:memcache ... [ 7.893686] krextd: Initialisation of krextd:memcache [OK] [ 7.899274] krextd: Initialisation of krextd:igmpcompr ... [ 7.904917] krextd: Initialisation of krextd:igmpcompr [OK] [ 7.910646] krextd: Initialisation of krextd:krextdev ... [ 7.916251] krextd: Initialisation of krextd:krextdev [OK] [ 7.921850] krextd: Initialisation of krextd:krextdev_wland ... [ 7.927978] krextd: Initialisation of krextd:krextdev_wland [OK] [ 7.934125] krextd: Initialisation of krextd:netdevice_notifier ... [ 7.940587] krextd: Initialisation of krextd:netdevice_notifier [OK] [ 7.947115] krextd: Initialisation of krextd:krextdprocfs ... [ 7.953095] krextd: Initialisation of krextd:krextdprocfs [OK] [ 7.959042] krextd: Initialisation of krextd:krextdtimer ... [ 7.964888] krextd: Initialisation of krextd:krextdtimer [OK] [ 7.970779] krextd: Initialisation of krextd [OK] [ 7.975614] krextd: Initialisation [OK] [ 8.018877] [module-mem] give 0x5000 bytes at 81180000 to module 'zram' (0x437000 bytes left) [ 8.033394] zram: Added device: zram0 [Supervisor] Info: modules-load.service exit success [Supervisor] Info: start devnodes.service [Supervisor] Info: devnodes.service exit success [Supervisor] Info: start apparmor.service [Supervisor] Info: start default-files.service [Supervisor] Info: start swap.service [Supervisor] Info: apparmor.service exit success [ 8.439956] zram0: detected capacity change from 0 to 8388608 Setting up swapspace version 1, size = 8384512 bytes [ 8.498221] Adding 8188k swap on /dev/zram0. Priority:-1 extents:1 across:8188k SS [Supervisor] Info: swap.service exit success [ 8.547552] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=0 NormP=0 mW → SumNormP=0 mW [ 8.561966] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_loadrate: norm_power_rate=100 act_rate=100 mul=10 div=1 offset=0 NormP=1000 mW → SumNormP=1000 mW [ 8.576991] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_dspclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=0 NormP=0 mW → SumNormP=1000 mW [ 8.591692] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=2200 NormP=2200 mW → SumNormP=3200 mW [ 8.607184] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=0 mul=84 div=10 offset=100 NormP=940 mW → SumNormP=4140 mW [ 8.621881] [avm_power]pm_ressourceinfo_scriptparse: powerdevice_ethernet: norm_power_rate=167 act_rate=0 mul=1 div=1 offset=50 NormP=217 mW → SumNormP=4357 mW [Supervisor] Info: default-files.service exit success [Supervisor] Info: start config.service [Supervisor] Info: start debug.service [Supervisor] Info: start sysctl.service net.ipv4.tcp_min_snd_mss = 536 [ 8.756253] sysrq: SysRq : Changing Loglevel [ 8.760656] sysrq: Loglevel set to 4 [ 8.765897] [ 8.765897] [avm_debug] redirecting kernel-messages (/dev/debug) kernel.panic_on_oops = 1 vm.panic_on_oom = 2 kernel.printk = 4 net.ipv4.ip_forward = 1 net.ipv4.tcp_min_tso_segs = 100 net.ipv4.conf.all.rp_filter = 1 net.ipv4.conf.default.rp_filter = 1 [Supervisor] Info: sysctl.service exit success [Supervisor] Info: debug.service exit success [Supervisor] Info: config.service exit success [Supervisor] Info: start avmipcd.service [Supervisor] Info: start boxnotify.service [Supervisor] Info: start inetd.service [Supervisor] Info: start psupport-init-prenet.service [Supervisor] Info: start run_clock.service [Supervisor] Info: inetd.service exit success run_clock demon started
[Supervisor] Info: run_clock.service exit success [Supervisor] Info: psupport-init-prenet.service exit success [Supervisor] Info: boxnotify.service exit success [Supervisor] Info: avmipcd.service exit success [Supervisor] Info: start net.service [Supervisor] Info: start avmnexusd.service /etc/ewnw_devfiles.sh: checking /dev files .... /etc/ewnw_devfiles.sh: /dev/kdsldptrace0 already exists /etc/ewnw_devfiles.sh: /dev/kdsldptrace1 already exists /etc/ewnw_devfiles.sh: mknod /dev/knqos c 246 0 /etc/ewnw_devfiles.sh: mknod /dev/avmtrackd c 245 0 /etc/ewnw_devfiles.sh: mknod /dev/avmtrackdquery c 244 0 /etc/ewnw_devfiles.sh: mknod /dev/bridgeflt c 243 0 /etc/ewnw_devfiles.sh: mknod /dev/krextd c 242 0 /etc/ewnw_devfiles.sh: mknod /dev/krextd_wlan c 241 0 /etc/ewnw_devfiles.sh: /dev files checked Jan 1 01:00:09 l2tpv3d[451]: starting ... (normal) Jan 1 01:00:09 avmnexusd[417]: starting ... (normal) 1970-01-01 01:00:09 l2tpv3d[451]: ready (0sec) Jan 1 01:00:09 l2tpv3d[454]: started. Jan 1 01:00:09 l2tpv3d[454]: verbose: DISABLED 1970-01-01 01:00:09 avmnexusd[417]: ready (0sec) [Supervisor] Info: avmnexusd.service exit success Jan 1 01:00:10 ctlmgr[460]: pcpc_create_ctx: no pcpserver found Jan 1 01:00:10 upnpd[464]: starting ... (normal) 1970-01-01 01:00:10 upnpd[464]: ready (0sec) Jan 1 01:00:12 rextd[526]: starting ... (normal) Jan 1 01:00:12 ctlmgr[461]: WLANLIB: wlan_plugin_init:868: prj revision 0x1c35e1c Jan 1 01:00:13 ctlmgr[461]: WLANLIB: wlan_libs_nexus_init:260: Get Nexus info failed: try again later. 1970-01-01 01:00:13 rextd[526]: ready (1sec) rc.wlan: Start WLAN... WLAND:[00545]:01:00.14/[0014.390]:[VER]Registered new module default, DEFAULT, 0 WLAND:[00545]:01:00.14/[0014.390]:[VER]Registered new module global, GLOBAL, 0 WLAND:[00545]:01:00.14/[0014.390]:[ALW]BUILD: Jun 1 2021, 16:40:24 Jan 1 01:00:14 deviceinfod[548]: starting ... (normal) 1970-01-01 01:00:14 deviceinfod[548]: ready (0sec) [Supervisor] Info: net.service exit success [Supervisor] Info: start kpid.service [Supervisor] Info: start meshd.service [Supervisor] Info: start ptest_release.service [Supervisor] Info: ptest_release.service exit success [Supervisor] Info: start configd.service kpid: Sending section usb failed with error -1: sysfs_usb 1 {“sv”:“gen/v1”,“kpi”:{}} kpid: Sending section hwpa failed with error -1: sysfs_hwpa 1 {“sv”:“gen/v1”,“kpi”:{}} kpid: Sending section system failed with error -1: sysfs_system 1 {“sv”:“gen/v1”,“kpi”:{“temperatures”:{“lm75_avg”:null,“lm75_max”:null,“lm75_min”:null}}} Jan 1 01:00:14 ctlmgr[461]: WLANLIB: wcsi_socket_connect:313: Establishing RPC connection failed with TIMEOUT [Supervisor] Info: configd.service exit success Jan 1 01:00:18 meshd[553]: LOG: main: Hello from meshd. Jan 1 01:00:18 meshd[553]: starting ... (normal) Jan 1 01:00:18 meshd[574]: verbose: DISABLED 1970-01-01 01:00:18 meshd[553]: ready (0sec) [Supervisor] Info: meshd.service exit success [Supervisor] Info: start meshd_config.service [Supervisor] Info: meshd_config.service exit success [Supervisor] Info: all Services loaded. Jan 1 01:00:20 meshd[574]: wlancsi_control: Request for get_roles failed. Task status is: TIMEOUT Jan 1 01:00:20 meshd[574]: wlancsi_control: Get roles failed! (Event registration will fail as well.): task timeout: Connection timed out Jan 1 01:00:39 l2tpv3d[662]: starting ... (normal) Jan 1 01:00:39 l2tpv3d[664]: [664] Start failed
OpenWrt bootlog
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING