ZyXEL Keenetic Lite III rev. A

Please choose the operation:

 1: Load system code to SDRAM via TFTP.
 2: Load system code then write to Flash via TFTP.
 3: Boot system code via Flash (default).
 4: Enter boot command line interface.
 7: Load Boot Loader code then write to Flash via Serial.
 9: Load Boot Loader code then write to Flash via TFTP.

U-Boot 1.1.3 [4.0.0.3-9] (Dec 11 2015 - 19:00:40)

Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. SSC disabled. spi_wait_nsec: 29 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV

Ralink UBoot Version: 4.0.0.3_NDMS

ASIC 7620_MP (Port5↔None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Dec 11 2015 Time:19:00:40

icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ #### estimate memory size = 64 Mbytes Firmware test register status: 0x00000000

Please choose the operation:

 1: Load system code to SDRAM via TFTP.
 2: Load system code then write to Flash via TFTP.
 3: Boot system code via Flash (default).
 4: Enter boot command line interface.
 7: Load Boot Loader code then write to Flash via Serial.
 9: Load Boot Loader code then write to Flash via TFTP.                    0

3: System Boot system code via Flash. ## Booting image at bc050000 ...

 Image Name:   ZyXEL Keenetic Lite III
 Created:      2022-03-23  13:59:39 UTC
 Image Type:   MIPS Linux Kernel Image (lzma compressed)
 Data Size:    1147510 Bytes =  1.1 MB
 Load Address: 80000000
 Entry Point:  802699f0
 Verifying Checksum ... OK
 Uncompressing Kernel Image ... OK

No initrd ## Transferring control to Linux (at address 802699f0) ... ## Giving linux memsize in MB, 64

Starting kernel ...

LINUX started... Linux version 3.4.113 (developers@ndmsystems.com) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-ndm-18 - NDMS Toolkit 1.0.0) ) #1 Tue Oct 17 19:11:50 MSK 2017 MediaTek SoC: MT7620N, RevID: 0206, RAM: DDR1, XTAL: 20MHz CPU/OCP/SYS frequency: 580/193/193 MHz CPU revision is: 00019650 (MIPS 24KEc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges:

Normal

0x00000000 → 0x00004000 Movable zone start PFN for each node Early memory PFN ranges

  0: 0x00000000 -> 0x00004000

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,57600n8 rdinit=/sbin/init PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Writing ErrCtl register=0005effa Readback ErrCtl register=0005effa Memory: 61664k/65536k available (2494k kernel code, 3872k reserved, 533k data, 168k init, 0k highmem) NR_IRQS:40 console [ttyS0] enabled Calibrating delay loop... 385.02 BogoMIPS (lpj=770048) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 Switching to clocksource MIPS NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 120 io scheduler noop registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A Registering NDM partitions parser Ralink SPI flash driver, SPI clock: 24MHz SPI flash chip: W25Q64BV (ef 40170000) (8192 Kbytes) Bootloader is up to date 8 ndmpart partitions found on MTD device raspi Creating 8 MTD partitions on “raspi”: 0x000000000000-0x000000030000: “U-Boot” 0x000000030000-0x000000040000: “U-Config” 0x000000040000-0x000000050000: “RF-EEPROM” 0x000000050000-0x000000180000: “Kernel” 0x000000180000-0x0000007f0000: “RootFS” mtd: device 4 (RootFS) set to be root filesystem 0x000000050000-0x0000007f0000: “Firmware” 0x0000007f0000-0x000000800000: “Config” 0x000000000000-0x000000800000: “Full” tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky maxk@qualcomm.com PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 nf_conntrack version 0.5.0 (16384 buckets, 32768 max) xt_time: kernel timezone is -0000 ubridge: Tiny bridge driver, 1.1 IPv4 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver Fast NAT loaded ip_tables: (C) 2000-2006 Netfilter Core Team TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 VFS: Mounted root (squashfs filesystem) readonly on device 31:4. Freeing unused kernel memory: 168k freed init: can't start a “mtdchk” process (could not execute: no such file or directory). init: press Enter to activate this console. [I] Jan 1 00:00:03 ndm: Core::Main: * [I] Jan 1 00:00:03 ndm: Core::Main: * Network Device Manager v2.08(AAUQ.4)C2. [I] Jan 1 00:00:03 ndm: Core::Main: * Built Oct 17 2017 19:07:58. [I] Jan 1 00:00:03 ndm: Core::Main: * [I] Jan 1 00:00:03 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/aead.ko. [I] Jan 1 00:00:03 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_DSCP.ko. [I] Jan 1 00:00:04 ndmip_gre: GRE over IPv4 tunneling driver : Core::System::DriverManager: loading /lib/phr: module license 'Proprietary' taints kernel. modules/3.4.113/phr: I/O peripheral driver. (C) 2013-2016, NDM Systems Inc., v2.0.6 xt_statistic.ko.phr: “kl_rf” platform driver loaded

[I] Jan 1 00:00:04 L2TP kernel driver, v1.5-1 ndm: Core::System::DriveLoad Ralink WDG Timer Module rManager: loading /lib/modules/3.4.113/xt_CLASSIresetnds: Module loaded. FY.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ip_gre.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ipt_ROUTE.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_length.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/phr.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_dscp.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/pppol2tp.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_hl.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/rt_timer_wdg.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ipt_ECN.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_ecn.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_comment.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/mtdoops_proc.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/resetnds.ko. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_string.ko. [I] Jan 1 00:00:04 ndm: FileSystem::Temp: mounting /var/... [I] Jan 1 00:00:04 ndm: Corertsoc_eth: Ethernet switch driver for Ralink SoCs ::Authenticator:rtsoc_eth: (C) 2016-2017, NDM Systems Inc., v1.1.48 MD5 generator crtsoc_eth: MT7620 SoC, TX/RX buffers: 512/512, poll budget 32 reated. [Irtsoc_eth: 04:bf:6d:65:5d:c0 address assigned to eth2 ] Jan 1 00:00:04 ndm: Core::Authenticator: NT generator created. [I] Jan 1 rtsoc_eth: MT7620 switch initialized 00:00:04 ndm: Core::Mode: “router” mode selected. [I] Jan 1 00:00:04 ndm: Core::Authenticator: “readonly” tag registered. [I] Jan 1 00:00:04 ndm: Core::System::Timezone: building a timezone list... [I] Jan 1 00:00:04 ndm: Core::System::Timezone: scanning done, 138 timezone available. [I] Jan 1 00:00:04 ndm: Core::System::Timezone: timezone reset to default. [I] Jan 1 00:00:04 ndm: Telnet::Server: bruteforce detection is enabled. [I] Jan 1 00:00:04 ndm: Ntp::Client: configuration reset. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/rtsoc_eth.ko. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Mac: backed up the default address 04:bf:6d:65:5d:c0 of “FastEthernet0” before changing. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/0”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/0”: interface is up. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/0”: renamed to “0”. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/1”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/1”: interface is up. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/1”: renamed to “1”. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/2”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/2”: interface is up. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/2”: renamed to “2”. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/3”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/3”: interface is up. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/3”: renamed to “3”. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/4”: interface is down. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/4”: interface is up. [I] Jan 1 00:00:04 ndm: Network::Interface::Base: “FastEthernet0/4”: renamed to “4”. Waiting for Wireless Events from interfaces... [I] Jan 1 00:00:04 ndm: Http::Manager: bruteforce detection is enabled. [I] Jan 1 00:00:04 ndm: Core::Authenticator: “http” tag registered. [I] Jan 1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/mt76x2_ap.ko. MT76x2 AP Driver version: 3.0.5.0 [I] Jan 1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: PHY mode set. [I] Jan 1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: country code set. [I] Jan 1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: channel bandwidth settings reset to default. [I] Jan 1 00:00:06 ndm: Network::Interface::Radio: the radio switch state is changed to off, software state is down [WifiMaster0]. [I] Jan 1 00:00:06 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint2”: interface is down. [I] Jan 1 00:00:06 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint1”: interface is down. [I] Jan 1 00:00:06 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint0”: SSID reset. [I] Jan 1 00:00:06 ndm: Network::Interface::Wifi: WPA PSK set. [I] Jan 1 00:00:06 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint0”: interface is down. [I] Jan 1 00:00:06 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint3”: interface is down. [I] Jan 1 00:00:06 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint2”: security level set to “private”. [I] Jan 1 00:00:06 ndm: Network::Interface::Base: “WifiMaster0/WifiStation0”: interface is down. [I] Jan 1 00:00:06 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint1”: security level set to “private”. [I] Jan 1 00:00:06 ndm: Module::Manager: loaded 22 modules. [I] Jan 1 00:00:06 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint3”: security level set to “private”. [I] Jan 1 00:00:06 ndnproxy: ndnproxy 1.2.3b10 started. [I] Jan 1 00:00:06 ndnproxy: PID file: /var/ndnproxymain.pid. [I] Jan 1 00:00:06 ndnproxy: stats. file: /var/ndnproxymain.stat. [I] Jan 1 00:00:06 ndm: Network::Interface::Radio: the radio switch state is changed to on, software state is down [WifiMaster0]. [I] Jan 1 00:00:07 ndm: FileSystem::Proc: system setting saved. [I] Jan 1 00:00:07 ndm: Core::Syslog: last message repeated 13 times. [I] Jan 1 03:00:07 ndm: Core::System::Timezone: timezone set to “Europe/Moscow”. [I] Feb 10 09:16:50 ndm: Core::System::Clock: system time has been changed. [I] Feb 10 09:16:50 ndm: Core::System::Domainname: the system domain name set. [I] Feb 10 09:16:50 ndm: Core::System::Hostname: the host name set. [I] Feb 10 09:16:50 ndm: Ntp::Client: server “0.pool.ntp.org” has been added. [I] Feb 10 09:16:50 ndm: Ntp::Client: server “1.pool.ntp.org” has been added. [I] Feb 10 09:16:50 ndm: Ntp::Client: server “2.pool.ntp.org” has been added. [I] Feb 10 09:16:50 ndm: Ntp::Client: server “3.pool.ntp.org” has been added. [I] Feb 10 09:16:50 ndm: Command::LogResponse: applied. [I] Feb 10 09:16:50 ndm: Core::Authenticator: user “admin” tagged with “cli”. [I] Feb 10 09:16:50 ndm: Core::Authenticator: user “admin” tagged with “http”. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/0”: renamed to “0”. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/0”: access mode enabled. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/0”: set access VLAN ID: 2. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/0”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/1”: renamed to “1”. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/1”: access mode enabled. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/1”: set access VLAN ID: 1. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/1”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/2”: renamed to “2”. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/2”: access mode enabled. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/2”: set access VLAN ID: 1. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/2”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/3”: renamed to “3”. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/3”: access mode enabled. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/3”: set access VLAN ID: 1. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/3”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/4”: renamed to “4”. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/4”: access mode enabled. [I] Feb 10 09:16:50 ndm: Network::Interface::Switch: “FastEthernet0/4”: set access VLAN ID: 1. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/4”: interface is up. [I] Feb 10 09:16:50 ndm: Network::Interface::Base: “FastEthernet0/Vlan1”: interface is down. [I] Feb 10 09:16:50 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan1. [I] Feb 10 09:16:51 ndm: Network::Interface::Base: “FastEthernet0/Vlan1”: description saved. [I] Feb 10 09:16:51 ndm: Network::Interface::IP: “FastEthernet0/Vlan1”: security level set to “private”. [I] Feb 10 09:16:51 ndm: Dhcp::Client: FastEthernet0/Vlan1 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:51 ndm: Dhcp::Client: FastEthernet0/Vlan1 DHCP name servers are enabled. [I] Feb 10 09:16:51 ndm: Network::Interface::Base: “FastEthernet0/Vlan1”: interface is up. [I] Feb 10 09:16:51 ndm: Network::Interface::Base: “FastEthernet0/Vlan2”: interface is down. [I] Feb 10 09:16:51 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan2. [I] Feb 10 09:16:52 ndm: Network::Interface::Base: “FastEthernet0/Vlan2”: renamed to “ISP”. [I] Feb 10 09:16:52 ndm: Network::Interface::Base: “FastEthernet0/Vldevice eth2 entered promiscuous mode an2”: description saved. [I] Feb 10 09:16:52 ndm: Network::Interface::IP: “FastEthernet0/Vlan2”: security level set to “public”. [I] Feb 10 09:16:52 ndm: Dhcp::Client: started DHCP client on FastEthernet0/Vlan2. [I] Feb 10 09:16:52 ndm: Dhcp::Client: FastEthernet0/Vlan2 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:52 ndm: Dhcp::Client: FastEthernet0/Vlan2 DHCP name servers are enabled. [I] Feb 10 09:16:52 ndm: Network::Interface::IP: “FastEthernet0/Vlan2”: global priority is 700. [I] Feb 10 09:16:52 ndm: Igmp::Proxy: upstream role assigned to FastEthernet0/Vlan2. [I] Feb 10 09:16:52 ndm: Network::Interface::Base: “FastEthernet0/Vlan2”: interface is up. [I] Feb 10 09:16:52 ndm: Network::Interface::Base: “FastEthernet0/Vlan3”: interface is down. [I] Feb 10 09:16:52 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan3. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “FastEthernet0/Vlan3”: description saved. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “FastEthernet0/Vlan3”: security level set to “private”. [I] Feb 10 09:16:53 ndm: Dhcp::Client: FastEthernet0/Vlan3 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: FastEthernet0/Vlan3 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “FastEthernet0/Vlan3”: interface is up. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiMaster: country code set. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiMaster: “WifiMaster0”: PHY mode set. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0”: interface is up. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint0”: renamed to “AccessPoint”. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint0”: description saved. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint0”: ACL type set. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint0”: security level set to “private”. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::Wps: “WifiMaster0/AccessPoint0”: WPS enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Wifi: WPA PSK set. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint0”: wireless encryption enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint0”: WPA2 algorithms enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint0 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint0 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Wireless: SSID saved. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint0”: WMM extensions enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint0”: interface is up. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint1”: renamed to “GuestWiFi”. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint1”: description saved. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint1”: ACL type set. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint1”: security level set to “private”. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint1 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint1 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Wireless: SSID saved. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint1”: WMM extensions enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint1”: interface is down. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint2”: ACL type set. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint2”: security level set to “private”. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint2 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint2 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint2”: interface is down. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: “WifiMaster0/AccessPoint3”: ACL type set. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “WifiMaster0/AccessPoint3”: security level set to “private”. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint3 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint3 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/AccessPoint3”: interface is down. [I] Feb 10 09:16:53 ndm: Network::Interface::IP: “WifiMaster0/WifiStation0”: security level set to “public”. [I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiStation: “WifiMaster0/WifiStation0”: wireless encryption disabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/WifiStation0 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/WifiStation0 DHCP name servers are enabled. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “WifiMaster0/WifiStation0”: interface is down. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “Bridge0”: interface is down. [I] Feb 10 09:16:53 ndm: Network::Interface::Base: “Bridge0”: interface is up. [I] Feb 10 09:16:53 ndm: Network::Interface::Repository: created interface Bridge0. [I] Feb 10 09:16:54 ndm: Network::Interface::Base: “Bridge0”: renamed to “Home”. [I] Feb 10 0device eth2.1 entered promiscuous mode 9:16:54 ndmbr0: port 1(eth2.1) entered forwarding state : Networbr0: port 1(eth2.1) entered forwarding state k::Interface::BaADDRCONF(NETDEV_CHANGE): br0: link becomes ready se: “Bridge0”: description saved. [I] Feb 10 09:16:54 evice ra0 entered promiscuous mode mndm: Nebr0: port 2(ra0) entered forwarding state twork::Interfacebr0: port 2(ra0) entered forwarding state ::Base: “Bridge0”: interface is up. [I] Feb 10 09:16:54 ndm: Network::Interface::Mac: backed up the default address f6:00:6d:3f:3c:d7 of “Home” before changing. [I] Febr0: port 2(ra0) entered disabled state b 10 09:16:54 r0: port 1(eth2.1) entered disabled state 32mndm: Network::Interface::IP: “Bridge0”: interface is non-global. [I] Feb 10 09:16:54 ndmr0: port 2(ra0) entered forwarding state 0m: kernel: br0: port 2(ra0) entered forwarding state br0: port 2(ra0)br0: port 1(eth2.1) entered forwarding state entered forwardbr0: port 1(eth2.1) entered forwarding state ing state [I] Feb 10 09:16:54 ndm: Network::Interface::Bridge: FastEthernet0/Vlan1 inherited in Bridge0. [I] Feb 10 09:16:55 ndm: kernel: br0: port 1(eth2.1) entered forwarding state [I] Feb 10 09:16:55 ndm: Network::Interface::Bridge: AccessPoint included in Bridge0. [I] Feb 10 09:16:55 ndm: Network::Interface::IP: “Bridge0”: security level set to “private”. [I] Feb 10 09:16:55 ndm: Network::Interface::IP: “Bridge0”: IP address is 192.168.1.1/24. [I] Feb 10 09:16:55 ndm: Dhcp::Client: Bridge0 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:55 ndm: Dhcp::Client: Bridge0 DHCP name servers are enabled. [I] Feb 10 09:16:55 ndm: Igmp::Proxy: added downstream interface Bridge0. [I] Feb 10 09:16:55 ndm: Network::Interface::Base: “Bridge0”: interface is up. [I] Feb 10 09:16:55 ndm: Network::Interface::Base: “Bridge1”: interface is down. [I] Feb 10 09:16:55 ndm: Network::Interface::Base: “Bridge1”: interface is up. [I] Feb 10 09:16:55 ndm: Network::Interface::Repository: created interface Bridge1. br0: port 2(ra0) entered forwarding state br0: port 1(eth2.1) entered forwarding state [I] Feb 10 09:16:56 ndm: Network::Interface::Base: device eth2.3 entered promiscuous mode “Bridge1”: renambr1: port 1(eth2.3) entered forwarding state ed to “Guest”.r1: port 1(eth2.3) entered forwarding state 0m [I] Feb 10 ADDRCONF(NETDEV_CHANGE): br1: link becomes ready 09:16:56 ndm: Network::Interface::Base: “Bridge1”: description saved. [I] Febdevice ra1 entered promiscuous mode 10 09:16:56 ndm: Network::Interface::Base: “Bridgebr1: port 1(eth2.3) entered disabled state 1”: interface is up. [I] Feb 10 09:16:56 r1: port 1(eth2.3) entered forwarding state [32mndm: r1: port 1(eth2.3) entered forwarding state mNetwork::Interface::Mac: backed up the default address 26:0c:aa:22:ff:7a of “Guest” before changing. [I] Feb 10 09:16:56 ndm: Network::Interface::IP: “Bridge1”: interface is non-global. [I] Feb 10 09:16:56 ndm: kernel: br1: port 1(eth2.3) entered disabled state [I] Feb 10 09:16:56 ndm: Network::Interface::Bridge: FastEthernet0/Vlan3 inherited in Bridge1. [I] Feb 10 09:16:56 ndm: kernel: br1: port 1(eigmpsn: IGMP switch snooping module (C) 2015, 2016 NDM Systems Inc., v4.0.34 th2.3) entered forwarding state [I] Feb 10 09:16:56 ndm: Network::Interface::Bridge: GuestWiFi included in Bridge1. [I] Feb 10 09:16:56 ndm: Network::Interface::IP: “Bridge1”: security level set to “protected”. [I] Feb 10 09:16:56 ndm: Network::Interface::IP: “Bridge1”: IP address is 10.1.30.1/24. [I] Feb 10 09:16:56 ndm: Dhcp::Client: Bridge1 DHCP client DNS host routes are enabled. [I] Feb 10 09:16:56 ndm: Dhcp:br0: port 2(ra0) entered disabled state :Client: Bridge1 DHCP name servers are enabled. [I] Feb 10 09:16:56 ndm: Network::Interface::Base: “Bridge1”: interface is up. [I] Feb 10 09:16:56 ndm: Dhcp::Pool: pool “_WEBADMIN” range has been saved. [I] Feb 10 09:16:56 ndm: Dhcp::Server: pool “_WEBADMIN” bound to interface Home. [I] Feb 10 09:16:56 ndm: Dhcp::Server: pool “_WEBADMIN” is enabled. [I] Feb 10 09:16:56 ndm: Dhcp::Pool: pool “_WEBADMIN_GUEST_AP” range has been saved. [I] Feb 10 09:16:56 ndm: Dhcp::Server: pool “_WEBADMIN_GUEST_AP” bound to interface Guest. [I] Feb 10 09:16:56 ndm: Dhcp::Server: pool “_WEBADMIN_GUEST_AP” is enabled. [I] Feb 10 09:16:56 ndm: Http::Manager: security level unchanged. [I] Feb 10 09:16:56 ndm: Http::Manager: bruteforce detection is reconfigured. [I] Feb 10 09:16:56 ndm: Command::LogResponse: NAT rule added. [I] Feb 10 09:16:56 ndm: Command::LogResponse: NAT rule added. [I] Feb 10 09:16:56 ndm: Telnet::Server: security level unchanged. [I] Feb 10 09:16:56 ndm: Telnet::Server: bruteforce detection is reconfigured. [I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::Ppe: software PPE enabled. [I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::Ppe: hardware PPE enabled. [I] Feb 10 09:16:56 ndm: UPnP::Manager: using LAN interface: Bridge0. [I] Feb 10 09:16:56 ndm: Dhcp::Server: service enabled. [I] Feb 10 09:16:56 ndm: Dns::Manager: DNS proxy enabled. [I] Feb 10 09:16:56 ndm: Igmp::Proxy: IGMP proxy enabled. [I] Feb 10 09:16:56 ndm: Http::Manager: HTTP service was enabled. [I] Feb 10 09:16:56 ndm: Telnet::Server: telnet server enabled. [I] Feb 10 09:16:56 ndm: Ntp::Client: NTP client enabled. [I] Feb 10 09:16:56 ndm: Core::Init: system ready, core startup time is 13 seconds. [I] Feb 10 09:16:56 ndm: Hotspot::Discovery::Explorer: Interface Bridge1 neighbour explorer started. [I] Feb 10 09:16:56 ndm: Hotspot::Discovery::Explorer: Interface Bridge0 neighbour explorer started. [I] Feb 10 09:16:56 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/igmpsn.ko. [I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::WifiMaster: “WifiMaster0”: auto channel mode set. br1: port 1(eth2.3) entered forwarding state [I] Feb 10 09:16:57 ndmbr0: port 2(ra0) entered forwarding state : Ntp::Clienbr0: port 2(ra0) entered forwarding state t: unable to communicate with “1.pool.ntp.org”. [I] Feb 10 09:16:57 ndm: Ntp::Client: could not synchronize, waiting... [I] Feb 10 09:16:57 ndm: kernel: bRalink/MTK HW NAT 5.0.2.0-5 Module Enabled, FoE Size: 16384 r0: port 2(ra0) entered forwarding state [I] Feb 10 09:16:SWNAT sizeof(bind) = 200 57 ndm:SWNAT sizeof(hashent) = 56 Core::System::DriverManager: loading /lib/mSWNAT is registered odules/3.4.113/hSWNAT enabled w_nat.ko. SWNAT caps: L2TP, PPTP, PPPoE, IPoE, MC, USB CDC/DSL[I] Feb 10 09:16 Fast VPN init, v4.0-86-5 :57 ndmPPPoE/IPoE LAN software acceleration is disabled : Core::System::DriverManager: loading /lib/modules/3.4.113/fastvpn.ko. [I] Feb 10 09:16:58 ndm: Http::Manager: new Web server configuration was applied. br0: port 2(ra0) entered forwarding state [I] Feb 10 09:16:58 ndhcps: _WEBADMIN: NDM DHCP server (version 3.1.14) started. [I] Feb 10 09:16:58 telnetd: waiting for connections... [I] Feb 10 09:16:58 ndm: Core::Server: started Session /var/run/ndm.core.socket. [I] Feb 10 09:16:58 ndm: Core::Server: client disconnected. [I] Feb 10 09:16:58 ndhcps: _WEBADMIN_GUEST_AP: NDM DHCP server (version 3.1.14) started. [I] Feb 10 09:16:58 ndm: Core::Server: started Session /var/run/ndm.core.socket. [I] Feb 10 09:16:58 ndm: Core::Server: client disconnected. [I] Feb 10 09:16:58 nimproxy: NDM IGMP/Multicast proxy (version 0.0.25) started. nginx: no NDM ACL support ACS result: primary channel 9, 40 MHz spectrum min dirty (with CCA) = 717 [I] Feb 10 09:17:04 wmond: WifiMaster0/AccessPoint0: (MT76x2) BSS(ra0) channel switched to 9. [I] Feb 10 09:17:09 ndm: Ntp::Client: unable to communicate with “2.pool.ntp.org”. [I] Feb 10 09:17:09 ndm: Ntp::Client: could not synchronize, waiting... [I] Feb 10 09:17:21 ndm: Ntp::Client: unable to communicate with “3.pool.ntp.org”. [I] Feb 10 09:17:21 ndm: Ntp::Client: could not synchronize, waiting...

U-Boot 1.1.3 [4.0.0.3-9] (Dec 11 2015 - 19:00:40)

Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. SSC disabled. spi_wait_nsec: 29 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV

Ralink UBoot Version: 4.0.0.3_NDMS

ASIC 7620_MP (Port5↔None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Dec 11 2015 Time:19:00:40

icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ #### estimate memory size = 64 Mbytes Firmware test register status: 0x00000000

Please choose the operation:

 1: Load system code to SDRAM via TFTP.
 2: Load system code then write to Flash via TFTP.
 3: Boot system code via Flash (default).
 4: Enter boot command line interface.
 7: Load Boot Loader code then write to Flash via Serial.
 9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash. ## Booting image at bc050000 ...

 Image Name:   MIPS OpenWrt Linux-5.15.94
 Created:      2023-03-01  14:37:21 UTC
 Image Type:   MIPS Linux Kernel Image (lzma compressed)
 Data Size:    2310015 Bytes =  2.2 MB
 Load Address: 80000000
 Entry Point:  80000000
 Verifying Checksum ... OK
 Uncompressing Kernel Image ... OK

No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64

Starting kernel ...

[ 0.000000] Linux version 5.15.94 (user@debian) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.2.0 r22153-107f7374c9) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 Wed Mar 1 14:37:21 2023 [ 0.000000] Board has DDR1 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is ZyXEL Keenetic Lite III (rev. A) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=0006abff [ 0.000000] Readback ErrCtl register=0006abff [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 56032K/65536K available (5592K kernel code, 601K rwdata, 1188K rodata, 1184K init, 215K bss, 9504K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015577] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.087805] pid_max: default: 32768 minimum: 301 [ 0.097247] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.111684] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129937] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.148687] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.168183] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.181782] pinctrl core: initialized pinctrl subsystem [ 0.193281] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.223519] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.234582] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.247241] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.258265] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.270843] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.281679] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.295914] clocksource: Switched to clocksource systick [ 0.307497] NET: Registered PF_INET protocol family [ 0.317430] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.332534] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.349124] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.364445] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.379691] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.393713] TCP: Hash tables configured (established 1024 bind 1024) [ 0.406490] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.419409] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.433591] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.444811] PCI: CLS 0 bytes, default 32 [ 0.452758] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.469211] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.487705] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.499222] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.521851] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.535578] printk: console [ttyS0] disabled [ 0.544086] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.563741] printk: console [ttyS0] enabled [ 0.563741] printk: console [ttyS0] enabled [ 0.580306] printk: bootconsole [early0] disabled [ 0.580306] printk: bootconsole [early0] disabled [ 0.613144] spi spi0.0: force spi mode3 [ 0.622434] spi-nor spi0.0: s25fl064k (8192 Kbytes) [ 0.632319] 6 fixed-partitions partitions found on MTD device spi0.0 [ 0.645042] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.659663] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 0.674562] Creating 6 MTD partitions on “spi0.0”: [ 0.684156] 0x000000000000-0x000000030000 : “U-Boot” [ 0.696688] 0x000000030000-0x000000040000 : “U-Config” [ 0.708276] 0x000000040000-0x000000050000 : “RF-EEPROM” [ 0.721749] 0x000000050000-0x0000007f0000 : “firmware” [ 0.733461] 2 uimage-fw partitions found on MTD device firmware [ 0.745360] Creating 2 MTD partitions on “firmware”: [ 0.755270] 0x000000000000-0x000000233fbf : “kernel” [ 0.765169] mtd: partition “kernel” doesn't end on an erase/write block -- force read-only [ 0.784672] 0x000000233fbf-0x0000007a0000 : “rootfs” [ 0.794656] mtd: partition “rootfs” doesn't start on an erase/write block boundary -- force read-only [ 0.814232] mtd: setting mtd5 (rootfs) as root device [ 0.825437] 1 squashfs-split partitions found on MTD device rootfs [ 0.837870] 0x000000570000-0x0000007a0000 : “rootfs_data” [ 0.850819] 0x0000007f0000-0x000000800000 : “Config” [ 0.861980] 0x000000000000-0x000000800000 : “Full” [ 0.904239] gsw: setting port4 to ephy mode [ 0.912801] mtk_soc_eth 10100000.ethernet: generated random MAC address 4a:01:6d:3f:2a:38 [ 0.929144] mtk_soc_eth 10100000.ethernet: no mdio-bus child node found [ 0.942334] mtk_soc_eth 10100000.ethernet: mdio-bus disabled [ 0.953838] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.966423] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.983619] rt2880_wdt 10000120.watchdog: Initialized [ 0.995250] NET: Registered PF_INET6 protocol family [ 1.012130] Segment Routing with IPv6 [ 1.019622] In-situ OAM (IOAM) with IPv6 [ 1.027640] NET: Registered PF_PACKET protocol family [ 1.037822] 8021q: 802.1Q VLAN Support v1.8 [ 1.062164] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.082837] Freeing unused kernel image (initmem) memory: 1184K [ 1.094684] This architecture does not have kernel memory protection. [ 1.107538] Run /sbin/init as init process [ 2.104093] init: Console is alive [ 2.111536] init: - watchdog - [ 3.520794] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.629596] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.650337] init: - preinit - [ 3.734194] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex) [ 5.599613] random: jshn: uninitialized urandom read (4 bytes read) [ 5.817991] random: jshn: uninitialized urandom read (4 bytes read) [ 6.223169] random: jshn: uninitialized urandom read (4 bytes read) [ 6.633865] random: jshn: uninitialized urandom read (4 bytes read) [ 7.176573] 8021q: adding VLAN 0 to HW filter on device eth0 [ 7.201919] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.800284] jffs2: notice: (295) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found. [ 7.833684] mount_root: switching to jffs2 overlay [ 7.851139] overlayfs: upper fs does not support tmpfile. [ 7.871958] urandom-seed: Seeding with /etc/urandom.seed [ 8.025200] procd: - early - [ 8.031426] procd: - watchdog - [ 8.400378] procd: - watchdog - [ 8.407460] procd: - ubus - [ 8.573889] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.590016] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.614131] random: ubusd: uninitialized urandom read (4 bytes read) [ 8.635406] procd: - init - Please press Enter to activate this console. [ 10.013773] random: jshn: uninitialized urandom read (4 bytes read) [ 10.133536] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.245577] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.902224] urngd: jent-rng init failed, err: 2 [ 10.932203] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2 [ 10.947397] Backport generated by backports.git v5.15.81-1-41-g02e352527db5 [ 11.588578] PPP generic driver version 2.4.2 [ 11.601179] NET: Registered PF_PPPOX protocol family [ 11.653059] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device “RF-EEPROM” [ 11.667910] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 11.683395] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected [ 11.795546] kmodloader: done loading kernel modules from /etc/modules.d/* [ 23.436790] random: crng init done [ 23.443590] random: 88 urandom warning(s) missed due to ratelimiting [ 39.248117] 8021q: adding VLAN 0 to HW filter on device eth0 [ 39.294251] device eth0 entered promiscuous mode [ 39.307779] br-lan: port 1(eth0.1) entered blocking state [ 39.318649] br-lan: port 1(eth0.1) entered disabled state [ 39.329805] device eth0.1 entered promiscuous mode [ 39.416927] br-lan: port 1(eth0.1) entered blocking state [ 39.427744] br-lan: port 1(eth0.1) entered forwarding state [ 40.257399] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready

BusyBox v1.36.0 (2023-02-26 17:15:33 UTC) built-in shell (ash)

_______                     ________        __

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -| || | | || _|| _| |_|| |_||||||| ||

        |__| W I R E L E S S   F R E E D O M

----------------------------------------------------- OpenWrt SNAPSHOT, r22153+3-107f7374c9

WARNING!

There is no root password defined on this device! Use the “passwd” command to set up a new password in order to prevent unauthorized SSH logins.

root@OpenWrt:/#