Show pagesourceOld revisionsBacklinksBack to top × Table of Contents Wansview NCS601W Supported Versions Hardware Highlights Installation Installation method: U-Boot TFTP + serial Specific configuration How to get motion to work IR LEDs Hardware Info Photos Opening the case Serial JTAG Bootlogs OEM bootlog OpenWrt bootlog Notes Tags Wansview NCS601W Under Construction! This page is currently under construction. You can edit the article to help completing it. NCS601W is a wireless IP camera with 640 x 480 CMOS sensor and IR LEDs for night view. Informative website: http://www.wanda25.de/wansview_ncs601w.html Possible clones: Belkin Netcam F7D7601v1 works with the OpenWrt image for the NCS601w 1) FCCid A5JC10150 leads to pictures showing imogenstudio +CAM Supported Versions BrandModelVersionCurrent ReleaseOEM InfoForum TopicTechnical DataWansviewNCS601W19.07.7http://www.wansview.us/Cloud-IP-Camera-p/ncs601w.htmView/Edit data Hardware Highlights ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSBNCS601WRalink RT5350F360864Ralink RT5350Fb/g/n-1--- Installation ModelVersionCurrent ReleaseFirmware OpenWrt InstallFirmware OpenWrt UpgradeFirmware OEM StockNCS601W19.07.7http://downloads.openwrt.org/releases/19.07.7/targets/ramips/rt305x/openwrt-19.07.7-ramips-rt305x-ncs601w-initramfs-kernel.binhttp://downloads.openwrt.org/releases/19.07.7/targets/ramips/rt305x/openwrt-19.07.7-ramips-rt305x-ncs601w-squashfs-sysupgrade.bin → Install OpenWrt (generic explanation) Installation method: U-Boot TFTP + serial boot initramfs (option 1 in U-Boot) flash sysupgrade via mtd (not possible via CLI or LuCI2)): mtd write /tmp/openwrt-ramips-rt305x-ncs601W-squashfs-sysupgrade.bin firmware Please mind that after installation of OpenWrt there are no video specific packages pre-installed, i.e. you have to install them manually. Alternatively you can compile your own image with all necessary packages already included. Specific configuration How to get motion to work See http://www.wanda25.de/wansview_ncs601w.html IR LEDs Controlled via GPIO8 3) Hardware Info FCCid A5JC10150 Architecture MIPS Vendor Ralink Bootloader U-Boot System-On-Chip Ralink RT5350F CPU/Speed 360 MHz Flash-Chip W25Q64BV Flash size 8 MiB RAM 64 MiB Wireless Ralink RT5350F 2.4GHz 802.11bgn Antenna 1x internal Ethernet 1x 10/100 Mbit/s USB No Serial Yes 57600 8N1 JTAG ? Camera on board Microphone on board Power supply 5 VDC, 1.5 A Buttons 2 buttons + 1 slider switch LEDs 8x IR Photos Insert photo of front of the casing Insert photo of back of the casing Insert photo of backside label Insert photo of PCB Opening the case Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, … Serial → port.serial general information about the serial port, serial port cable, etc. How to connect to the Serial Port of this specific device: See http://www.wanda25.de/wansview_ncs601w.html Serial connection parameters for Wansview NCS601W 57600, 8N1 JTAG → port.jtag general information about the JTAG port, JTAG cable, etc. How to connect to the JTAG Port of this specific device: Insert photo of PCB with markings for JTAG port Bootlogs OEM bootlog COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE OpenWrt bootlog COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING Notes Tags How to add tags ramips, RT5350, 8Flash, 64RAM, 1port, fastethernet, 802.11bgn, ip camera 1) , 2) , 3) http://www.wanda25.de/wansview_ncs601w.html This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.OKMore information about cookies ramips rt5350 8Flash 64RAM 1port fastethernet 802.11bgn ip camera Last modified: 2021/01/30 11:05by danitool