Vodafone H300s

----
PRELOADER.00000000.LPLR.19767609.
II: SNAF version check OK!
TLB initial done:
    .ro section works!
    .text and .ro sections work!
Light Power LED ON!

II: LDO setup...
II: DRAM init...


Start to set DDR parameters 

ENABLE: Triple SYNC

TRIG: DRAM initialization procedure, wait done bit...Done!

PLL: MEMPLL31 = 0x10407f
PLL: MEMPLL63 = 0xc00001ef
PLL: MEMPLL95 = 0x26622760
PLL: MEMPLL127 = 0x270f0000
PLL: MEMPLL159 = 0xfff
PLL: MEMPLL191 = 0x0
PLL: MEMPLL223 = 0x0
System FREQ. info:OCP0: 0x3e8 MHz, OCP1: 0x1f4 MHz, DRAM: 0x20d MHz, LX: 0xc8 MHz

Slow bits configuration:

0xb8000380: 0x80000070

0xb8000390: 0x80000070

0xb8000388: 0x22200

0xb8000398: 0x200

0xb80003a0: 0xf000f

SCATS settings:

0xb80040f8: 0xc5


******* DRAM calibration version: v2.0 (r87105-0x4552c) *******
ZQ: Clock GROUP

ZQ: ODT/OCD= 33/30

ZQ: zq_zctrl_prog=0x80803be  zq_zctrl_status=0x18a133

ZQ: Address GROUP

ZQ: ODT/OCD= 33/48

ZQ: zq_zctrl_prog=0x180803b4  zq_zctrl_status=0x18a111

ZQ: DQ GROUP

ZQ: ODT/OCD= 33/3c

ZQ: zq_zctrl_prog=0x280803b8  zq_zctrl_status=0x18a122

ZQ: DQS GROUP

ZQ: ODT/OCD= 33/3c

ZQ: zq_zctrl_prog=0x380803b8  zq_zctrl_status=0x18a122

ZQ: ZQ Calibration PASS!

MRS: mr[0] = 100c72

MRS: mr[1] = 110006

MRS: mr[2] = 120000

MRS: mr[3] = 130000

AK: Start DDR_Calibration...

AK: Reduce DDR calibration

AK: Bit:0 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:2 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:3 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:4 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:5 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:6 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:7 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:8 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:9 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:a max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:b max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:c max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:d max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:e max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:f max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:10 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:11 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:12 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:13 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:14 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:15 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:16 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:17 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:18 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:19 max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1a max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1b max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1c max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1d max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1e max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

AK: Bit:1f max_r_s:0 max_r_l:1f max_w_s:0 max_w_l:1f 

ENABLE: DQ output enable delay SYNC

AK: Finish DDR Calibration

DCR: 0x21220000

DTR: tRFC[DRAM_capacity_index]=80

DTR: DRAM_capacity_index=3

DTR: dram_freq_mhz=20d

DTR: tRFC=10680
DTR: DTR0=77544e26, DTR1=606051c, DTR2=4617000
DISABLE: Read after Write

ENABLE: Parallel Bank & Read Buffer Patch

II: Change Stack from 0x9f000edc to 0x83bfffe0
II: U-boot Magic Number is 0x27051956
II: Inflating U-Boot (0x83c00040 -> 0x83c00000)... OK
II: Starting U-boot... 


U-Boot 2011.12.1M-svn1 (Mar 04 2018 - 13:30:26)

Board: VD2, CPU:1000MHz, LX:200MHz, DDR2:525MHz
DRAM: 128 MB
SPI-NAND Flash: C8DEFA/Mode0 1x128MB
Create bbt: 1023 
Don't use bad block skip table!
Loading 16384B env. variables from offset 0x200000
Net:   Ext. phy is not found. 

RTL SwCore
Warning: eth device name has a space!
SC_DEBUG: Nand Partition Table Magic Found at 100000.
reading at Bi 0x8
reading at Bi 0x376
10 50 72 c 61 8 

Prod Buil, No Chance to get into CLI!
Load Standalone Code from flash to buffer address in DRAM...
Standalone:SC_DEBUG: Nand Partition Table Magic Found at 100000.
Standalone:SC_DEBUG: Nand Partition Table Magic Found at 100000.
SC_DEBUG: Nand Partition Table Magic Found at 100000.
Standalone:SC_DEBUG: Nand Partition Table Magic Found at 100000.
Standalone:SC_DEBUG: Nand Partition Table Magic Found at 100000.


***************************************************

    Sercomm Boot Version 1.1.0.0, at Mar  4 2018, 13:31:09



***************************************************

M T
DEBUG_INF:SC Factory Burn-In Mode!
DEBUG_INF:record_loop 30, target_loop 30
DEBUG_INF:*********************RECORD == TARGET, FINISHED*****************
[rtl8676_halt(63)] Halt
Ethernet is closed!

Entering Firmware : Everything is OK.

Dual Image Selection Flag Value 0x3
ubi part kfs2
Creating 1 MTD partitions on "nand0":
0x0000034c0000-0x0000064c0000 : "mtd=8"
UBI: attaching mtd5 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
UBI: attached mtd5 to ubi0
UBI: MTD device name:            "mtd=8"
UBI: MTD device size:            48 MiB
UBI: number of good PEBs:        384
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     2
UBI: available PEBs:             216
UBI: total number of reserved PEBs: 168
UBI: number of PEBs reserved for bad PEB handling: 3
UBI: max/mean erase counter: 1/0
kernel_size 0x329800, roofs_size 0xe5e000
ubi readvol 0x80000000 ubi_vol_kernel
Read 0 bytes from volume ubi_vol_kernel to 80000000
No size specified -> Using max size (3315712)
Verifing Kernel Image Check Sum:PASS!
ubi readvol 0x80000000 ubi_vol_rootfs
Read 0 bytes from volume ubi_vol_rootfs to 80000000
No size specified -> Using max size (15110144)
Verifing Rootfs Image Check Sum:PASS!
ubi readvol 0x83000000 ubi_vol_kernel
Read 0 bytes from volume ubi_vol_kernel to 83000000
No size specified -> Using max size (3315712)
## Booting kernel from Legacy Image at 83000000 ...
   Image Name:   Linux Kernel Image
   Created:      2019-08-30  11:41:40 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3313788 Bytes = 3.2 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 3.18.20-svn5235 (root@ubuntu) (gcc version 4.8.5 20150209 (prerelease) (Realtek MSDK-4.8.5p1 Build 2220) ) #1 SMP Fri Aug 30 19:00:45 CST 2019 [SDK 2.4.1]
Total DRAM Size=128M
 OCP0 DRAM Size=128M
MIPS: machine is RTL8685SB
[L2_DEBUG:(bsp_setup_syncctl,235)]mips_cm_base= bfbf8000
[L2_DEBUG:(bsp_setup_syncctl,236)]read_gcr_control() = 0x1  => [L2_DEBUG:(bsp_setup_syncctl,239)]0x10001
[L2_DEBUG:(bsp_scache_config,157)]L2_CONFIG= 0x11
[L2_DEBUG:(bsp_scache_config,168)] - L2_DataStall= 0x1
[L2_DEBUG:(bsp_scache_config,169)] - L2_TagStall = 0x0
[L2_DEBUG:(bsp_scache_config,170)] - L2_WsStall  = 0x1
[L2_DEBUG:(bsp_scache_config,171)] - L2_Bypass: Disable
[L2_DEBUG:(bsp_setup_scache,214)]SCache LineSize= 32 (B)
bootconsole [early0] enabled
CPU0 revision is: 0001a120 (MIPS interAptiv (multi))
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 07800000 @ 00000000 (usable)
Zone ranges:
  Normal   [mem 0x00000000-0x077fffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x077fffff]
Initmem setup node 0 [mem 0x00000000-0x077fffff]
VPE topology {2,2} total 4
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 9 pages/cpu @8283e000 s7552 r8192 d21120 u36864
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30480
Kernel command line:  console=ttyS0,115200 mtdparts=spinand:1024k(boot),512k(part_map),512k(dual_flag),512k(u-boot-env),512k(checksum1),512k(checksum2),1280k(protect),49152k(kfs1),49152k(kfs2),5120k(xml_config),5120k(app_data),1024k(factory) ubi.mtd=8 root=ubi0:ubi_vol_rootfs ro rootfstype=squashfs mem=120M
log_buf_len individual max cpu contribution: 4096 bytes
log_buf_len total cpu_extra contributions: 12288 bytes
log_buf_len min size: 4096 bytes
log_buf_len: 16384 bytes
early log buf free: 1128(27%)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 81392K/122880K available (7947K kernel code, 1490K rwdata, 1508K rodata, 240K init, 28938K bss, 41488K reserved)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 666.41 BogoMIPS (lpj=3332096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Performance counters: mips/interAptiv PMU enabled, 2 32-bit counters available to each CPU, irq -1 (share with timer interrupt)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU1 revision is: 0001a120 (MIPS interAptiv (multi))
Synchronize counters for CPU 1: done.
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU2 revision is: 0001a120 (MIPS interAptiv (multi))
Synchronize counters for CPU 2: done.
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU3 revision is: 0001a120 (MIPS interAptiv (multi))
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
NET: Registered protocol family 16
cpuidle: using governor ladder
cpuidle: using governor menu
pm-cps: CPC does not support clock gating
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
Switched to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
Realtek GPIO Driver for Flash Reload Default
futex hash table entries: 1024 (order: 4, 65536 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
ntfs: driver 2.1.31 [Flags: R/W].
fuse init (API version 7.23)
JFS: nTxBlock = 635, nTxLock = 5087
msgmni has been set to 158
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x18002000 (irq = 58, base_baud = 12327200) is a 16550A
console [ttyS0] enabled
console [ttyS0] enabled
bootconsole [early0] disabled
bootconsole [early0] disabled
console [ttyS0] disabled
console [ttyS0] enabled
SOC_ID 0x6518
unknown bond id
aipc: register chrdev(254,0)
aipc: create device successed
aipc: start aipc irq init
aipc: Request IRQ for IPC OK
aipc: create dsp console device successed
aipc: init done
/proc/usb_mount_failed_dev created.
Realtek Luna SPI NAND Flash Driver Rev:00:00:00 (ChaoYuan_Yang)
nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
nand: Unknown 
nand: 128MiB, SLC, page size: 2048, OOB size: 64
Scanning device for bad blocks
Bad eraseblock 1023 at 0x000007fe0000
12 cmdlinepart partitions found on MTD device spinand
RTK: using dynamic nand partition
Creating 12 MTD partitions on "spinand":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000180000 : "part_map"
0x000000180000-0x000000200000 : "dual_flag"
0x000000200000-0x000000280000 : "u-boot-env"
0x000000280000-0x000000300000 : "checksum1"
0x000000300000-0x000000380000 : "checksum2"
0x000000380000-0x0000004c0000 : "protect"
0x0000004c0000-0x0000034c0000 : "kfs1"
0x0000034c0000-0x0000064c0000 : "kfs2"
0x0000064c0000-0x0000069c0000 : "xml_config"
0x0000069c0000-0x000006ec0000 : "app_data"
0x000006ec0000-0x000006fc0000 : "factory"
Realtek SPI Nand Flash Driver is successfully installing.
IMQ: No specify the numqueues. Use the cores number 4 as numqueuues
IMQ driver loaded successfully. (numdevs = 2, numqueues = 4, imq_dev_accurate_stats = 1)
	Hooking IMQ after NAT on PREROUTING.
	Hooking IMQ before NAT on POSTROUTING.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
NET: Registered protocol family 24
Realtek WLAN driver driver version 3.6.3 (2017-10-03)
DFS function - version 2.0.14
Adaptivity function - version 9.3.4
CFG1 wdev->conf_addr:b8b30000,base_addr:ba000000
8685g pcie port 1
Warring!! Port 1 WLan device PCIE Link Failed, State=0xb5bc43
Reset PCIE Host PHY and try again...
PCIE_reset_procedure[1605]: Error!! Port 1 WLan device PCIE Link failed, State=0x4abc43
=====>> EXIT rtl8192cd_init_one (-19) <<=====
init_one fail!!! rc=-19
CFG0: wdev->conf_addr:b8b10000,base_addr:b9000000
8685g pcie port 0
MACHAL_version_init


#######################################################
SKB_BUF_SIZE=3032 MAX_SKB_NUM=400
#######################################################

usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_ncm



Probing RTL8186 10/100 NIC-kenel stack size order[2]...
  Tx/Rx/Alloc = 1024/1024/3072
chip name: 8196B, chip revid: 0
NOT YET
Start to initiate QM
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 2
Set Queue Descriptor Base Flow Control Para Error.
Set threshould idx 0
Set Queue Descriptor Base Flow Control Para Error.
set phyid 0 1 2 3 4
re865x_probe(7668): b80100a4=00186180
eth0.2 added. vid=9 Member port 0x1...
eth0.3 added. vid=9 Member port 0x2...
eth0.4 added. vid=9 Member port 0x4...
eth0.5 added. vid=9 Member port 0x8...
eth0.6 added. vid=9 Member port 0x10...
nas0 added. vid=8 Member port 0x0...
ptm0 added. vid=8 Member port 0x20...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_rtl86xx_driver_probe
2 ehci_rtl86xx_driver_probe
rtl86xx-ehci rtl86xx-ehci: Realtek rtl819x On-Chip EHCI Host Controller
rtl86xx-ehci rtl86xx-ehci: new USB bus registered, assigned bus number 1
rtl86xx-ehci rtl86xx-ehci: irq 30, io mem 0x18021000
rtl86xx-ehci rtl86xx-ehci: USB 2.0 started, EHCI 1.00
Unsupported USB interface.
Unsupported Device.
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rtl86xx-ohci rtl86xx-ohci: Realtek rtl819x built-in OHCI controller
rtl86xx-ohci rtl86xx-ohci: new USB bus registered, assigned bus number 2
rtl86xx-ohci rtl86xx-ohci: irq 30, io mem 0x18020000
Unsupported USB interface.
Unsupported Device.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Unsupported USB interface.
Unsupported Device.
Unsupported USB interface.
Unsupported Device.
usbcore: registered new interface driver cdc_wdm
Unsupported USB interface.
Unsupported Device.
Unsupported USB interface.
Unsupported Device.
usbcore: registered new interface driver usb-storage
cpuidle-cps: limited to non-coherent wait
Unsupported USB interface.
Unsupported Device.
Unsupported USB interface.
Unsupported Device.
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
Realtek SD2-FastPath v1.00beta_2.4.26-uc0
/proc/FastPath created
/proc/FastPath_heavy_traffic_thres created
Realtek SD5-FastPath Realtek Ipv6FastPath-betaV0.01
/proc/Ip6FastPath created
Realtek IPv6 MCast FastPath
/proc/ip6mc_FastPath created
SPI Flash Driver for RTK SoC, Version 1.0.000
SFCR: ffc01244  SFCR2: 03e00000
unrecognized flash id 000000
rtk_map probe fail
ATM OAM F5 initialized.
ATM OAM F4 initialized.
Enable 8671G 1 function
Enable 8671 0 function
Enable 8672 function 
ratm: RTL8670 SAR v0.0.2 (Jun 17, 2003)
/proc/AUTO_PVC_SEARCH created
PTM: rtl8685_ptm_init entry
PTM: disable => enable IP, f07fffff
ptm_timer_init
Mirror/redirect action on
u32 classifier
    Actions configured
nf_conntrack version 0.5.0 (1271 buckets, 5084 max)
nf_conntrack_l2tp version 3.1 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
rtl_igmpsnoop_init-2430: init multicast snooping igmpInitFlag:0
rtl_mldsnoop_init-749:: mldSnoopEnabled:0
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
Ebtables v2.0 registered
l2tp_core: L2TP core driver, V2.0
l2tp_ppp: PPPoL2TP kernel driver, V2.0
UBI: attaching mtd8 to ubi0
UBI: scanning is finished
UBI: attached mtd8 (name "kfs2", size 48 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 384, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1909288411
UBI: available PEBs: 199, total reserved PEBs: 185, PEBs reserved for bad PEB handling: 20
UBI: background thread "ubi_bgt0d" started, PID 62
VoIP control bind 2 (2) instances successfully.
index dsp_cpuid dsp_cch host_cch
----- --------- ------- --------
   0  	   0	     0	     0	 
   1  	   0	     1	     1	 
 voip spin lock init done
VoIP RX netfilter hook init done!
VoIP RX netfilter hook for IPv6 init done!
=============RTK VOIP SUITE=============
SDK VoIP Version: VoIP-1.6-DSP-R5523-Luna-R15-PLATFORM_0822_5281-Rev59  2019-04-09 
Board CFG Model :  
INITIAL VOIP MANAGER PROGRAM
voip_events_init(719)Init Event Semaphore
VFS: Mounted root (squashfs filesystem) readonly on device 31:13.
Freeing unused kernel memory: 240K (80ab4000 - 80af0000)
random: init urandom read with 128 bits of entropy available
random: nonblocking pool is initialized

init started: BusyBox v1.15.3 ()

starting pid 69, tty '': '/etc/rcS'
Sat Oct 10 10:10:00 UTC 1970
lan6_ip: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
<0>LAN6 IP module loaded.
Init LED Driver
Init LED&Button Module
insmod: can't insert '/lib/modules/networkmap.ko': No such file or directory
yaffs: dev is 32505862 name is "mtdblock6" ro
yaffs: passed flags ""
yaffs: dev is 32505865 name is "mtdblock9" rw
yaffs: passed flags ""
yaffs: dev is 32505866 name is "mtdblock10" rw
yaffs: passed flags ""
Turn on Power LED
Run Realtek configd
------------ Init VoIP
run dsp set script...
Unsupported USB interface.
Unsupported Device.
Unsupported USB interface.
Unsupported Device.
usbcore: registered new interface driver usblp
aipc: (0350)prepare_BIR  

set_msgqueue_max_size:180> set msgqidds.msg_qbytes=35960 OK
set_msgqueue_max_size:180> set msgqidds.msg_qbytes=35960 OK
aipc: write image successful. size=3889264 rc=3889264 wc=3889264aipc: (0475)aipc_dev_ioctl  boot dsp
 da=0xb03c0400 remain=0

aipc: (0477)aipc_dev_ioctl  boot dsp done

Wait DSP 0/1 booting ......
.get_run_flag: run flag in /dev/mtd2 is 3
get_run_flag: run flag in /dev/mtd2 is 3
push button start
run rc script
aipc: (0462)aipc_dsp_disable_mem  
DSP 0 Software Ready!
Wait DSP 0/1 booting ......
DSP 0 Software Ready!
Inactive PIN_CS: 
aipc: (0216)aipc_module_voip_set_pcm_fs  SOC_ID 0x6518 is not handled
move this action after init
devicePcn = [75], deviceRcn = [8]]
FXS in LOW power modeFXS in LOW power modeVpSetOption for line IO failed. status = 6
VpSetOption for line IO failed. status = 6
Init_Event_Polling_Use_Timer(56) init rtl8685g high resolution timer
Request IRQ for timer2 OK!.
All DSP Software Ready. VoIP Defer Init done. 
start watch dog
/etc/rc_voip: line 18: /bin/voip_gwdt: not found
etherwan mode  : Enable
lan port 0 change to ethwan port
ethwan port: 0
==========New Function==========
enable previous port eth0.6
==========New Function==========
disable eth0.2
==========New Function==========
enable nas0:
New_swNic_init(299)
New_swNic_init(320):ring0=a5548000,1024
New_swNic_init(320):ring5=a5543000,64
New_swNic_init(420)
re865x_open 4071, nas0
IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready
0,1
/bin/sh: /usr/sbin/autosensed: not found
interface wlan1 does not exist!
interface wlan1-vap0 does not exist!
interface wlan1-vap1 does not exist!
interface wlan1-vap2 does not exist!
killall: radvd: no process killed
[Oct 10 13:10:19] nadvd: can't open /tmp/ipv6/radvd.conf: No such file or directory
[Oct 10 13:10:19] nadvd: Exiting, failed to read config file.

killall: dhcp6s: no process killed
[firewall/firewall.c][rcl_fw_start_input_mgnt_lan][67]: Firewall rule INPUT_MGNT_LAN_ACCESSCONTROL start!
bind: Address already in use
bind: Address already in use

sh_user_lib.c 270:user shHandlerAgent: shared memory size=260196,define size=524288,VmInfoCenterT size=75808

sh_user_lib.c 270:user shHandlerAgent: shared memory size=260196,define size=524288,VmInfoCenterT size=75808
shHandlerAgent: shared memory size=260196,define size=524288,VmInfoCenterT size=75808
 IcSipT =51204,
 IcCallFeatureT=8688,
 IcVoiceT= 11760,
 IcGeneralT=1628,
 IcSpyT=276,
 IcFciT=92

starting pid 1388, tty '': '/sbin/getty ttyS0 115200'


easybox login: