TP-Link Archer C6U v1 (EU)

Dual Band wireless 5GHz and 2.4GHz. Based on MediaTek chipset. Four 1Gbit LAN ethernet ports + One 1Gbit WAN ethernet port.

:!: Make sure your device is using a supported flash chip, read https://forum.openwrt.org/t/204907/.

TP-Link Archer C6U (EU)

None at this time.

Before setting up this router, do NOT connect it to the internet. Prevent it from activating the TP-Link cloud feature. Connect a cable using an ethernet LAN port to a computer with a ethernet port. The default IP of the router will be http://192.168.0.1, a DHCP server is active by default. If you have ever used your browser to setup this router once, there is a problem with a permanent redirect in the web GUI which will prevent you from login in with the correct password. (you will see a login loop using the correct password but no message that indicates a problem. When typing a wrong password it will show a popup box complaining). The simple remedy is to flash your router in an anonymous browser window, which will not be subject to the permanent redirect problem.

You can install OpenWRT from the firmware that comes with the C6U. To do so, click on the Advanced tab, choose System Tools from the left side menu, and pick Firmware Upgrade from the submenu options. In the main window, under Manual Upgrade, click Browse. Select the OpenWRT firmware file downloaded (see previous section). The filename may be of the form openwrt-21.02.1-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. you do not need to rename the file.

In two of three test cases it was observed that the System Tools menu did not contain the Manual upload firmware section. To enable this menu, After setting the admin password after first boot, you have to change the router Operation Mode in the menu. Just select whatever mode that is not selected. It will reboot the router and when you login again and navigate to the System Tools menu, you will see the Firmware Upgrade submenu now. In 1 test case, this problem did not happen.

If you happen to need to reset the router to it's defaults, keep the reset button pressed for 10 seconds and watch the LED behavior change, release and let it boot. These routers reboot fast.

For configuring the router after installing OpenWrt, follow the base-system documentation

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

In the current release this router is using the DSA (Distributed Switch Architecture) switch architecture. See dsa for more information

LAN ports are labeled in OpenWrt as they are on the router itself e.g : lan1-lan4 and the WAN port is wan, the ethernet switch is eth0 The physical numbering on the ports matches this.

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The TP-Link Archer C6U has the following buttons:

BUTTON Event
Reset reset
WPS wps

Front:
archer_c6u_v1.jpg

Back:
archer_c6u_v1_back.jpg

Backside label:
archer_c6u_v1_label.jpg

Note: This will void your warranty!

  • Unscrew the 2 screws at the back
  • The top cover snaps firmly in place so it still be quite stuck, you will need to pry it open close to the sides by inserting a hard (plastic) spoon to make the case more wide and then pry the cover upwards. Focus on one side, move a bit, repeat and after a few times, the cover will come of easily.

Main PCB:
archer_c6u_v1_pcb.jpg

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for TP-Link Archer C6U v1 (EU)
EXAMPLE 115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

5 fixed-partitions partitions found on MTD device spi0.0
Creating 5 MTD partitions on "spi0.0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000fa0000 : "firmware"
2 uimage-fw partitions found on MTD device firmware
Creating 2 MTD partitions on "firmware":
0x000000000000-0x000000250000 : "kernel"
0x000000250000-0x000000f60000 : "rootfs"
mtd: device 3 (rootfs) set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x0000005f0000-0x000000f60000 : "rootfs_data"
0x000000fa0000-0x000000fb0000 : "config"
0x000000fb0000-0x000000ff0000 : "tplink"
0x000000ff0000-0x000001000000 : "radio"

None so far.

#################################################################### # Archer C6U System Log # Time = 2023-08-29 00:11:29 # H-Ver = 1.0.0 ; S-Ver = 1.0.7 Build 20230829 rel.54335 # LAN: I = 192.168.0.1 ; M = 255.255.255.0 ; MAC = A8:42:A1:XX:XX:XX # WAN: W = dhcp ; I = 0.0.0.0 ; M = 0.0.0.0 ; MAC = A8:42:A1:XX:XX:XX # G = 0.0.0.0 ; D1 = 0.0.0.0 ; D2 = 0.0.0.0 # Clients connected: 1 ; WI-FI : 0 #################################################################### 2023-08-29 00:02:08 led-controller[771]: <6> 288051 Start to run WAN1_OFF 2023-08-29 00:02:08 led-controller[771]: <6> 288051 Start to run WAN0_OFF 2023-08-29 00:02:08 led-controller[771]: <6> 288051 Start to run LAN_ON 2023-08-29 00:01:13 led-controller[771]: <6> 288051 Start to run WAN1_OFF 2023-08-29 00:01:13 led-controller[771]: <6> 288051 Start to run WAN0_OFF 2023-08-29 00:01:13 led-controller[771]: <6> 288051 Start to run LAN_ON 2023-08-29 00:01:10 led-controller[771]: <6> 288051 Start to run STATUS_ON 2023-08-29 00:01:08 qos[6967]: <6> 259504 Service start 2023-08-29 00:01:08 qos[6967]: <6> 259503 Function disabled 2023-08-29 00:01:07 led-controller[771]: <6> 288051 Start to run GENERAL 2023-08-29 00:01:02 traffic-stats[6518]: <6> 269504 Service start 2023-08-29 00:00:56 factory-reset[6078]: <6> 284504 Service start 2023-08-29 00:00:55 parental-control[5909]: <6> 229504 Service start 2023-08-29 00:00:55 parental-control[5909]: <6> 229502 Function enabled 2023-08-29 00:00:54 access-control[5841]: <6> 239504 Service start 2023-08-29 00:00:54 access-control[5841]: <6> 239503 Function disabled 2023-08-29 00:00:53 nat[5408]: <7> 211001 Flush conntrack 2023-08-29 00:00:53 nat[5408]: <6> 211502 Function enabled 2023-08-29 00:00:53 nat[5408]: <5> 211051 Create NAT chain succeeded 2023-08-29 00:00:52 nat[5408]: <6> 211501 Initialization succeeded 2023-08-29 00:00:52 nat[5408]: <6> 211501 Initialization succeeded 2023-08-29 00:00:50 basic-security[5040]: <6> 219504 Service start 2023-08-29 00:00:50 basic-security[5040]: <5> 219606 Flush conntrack table succeeded 2023-08-29 00:00:49 firewall[2457]: <6> 209504 Service start 2023-08-29 00:00:46 led-controller[771]: <6> 288051 Start to run WIFI5G_ON 2023-08-29 00:00:46 led-controller[771]: <6> 288051 Start to run WIFI2G_ON 2023-08-29 00:00:45 imb[4206]: <6> 218507 Daemon connection succeeded 2023-08-29 00:00:45 imb[4206]: <6> 218012 ARP Binding disabled 2023-08-29 00:00:45 imb[4206]: <6> 218506 Config interface initialization succeeded 2023-08-29 00:00:45 imb[4206]: <6> 218501 Initialization succeeded 2023-08-29 00:00:43 upnp[3522]: <6> 217504 Service start 2023-08-29 00:00:35 upnp[3522]: <6> 217505 Service stop 2023-08-29 00:00:27 remote-management[2781]: <6> 282505 Service stop 2023-08-29 00:00:27 dhcpc[2669]: <6> 210056 teardown and release 2023-08-29 00:00:26 dhcpc[2669]: <6> 210051 send discover with ip 0.0.0.0 and flags 80 2023-08-29 00:00:06 modem[1457]: <7> 292032 proto_init_config: proto=qmi 2023-08-29 00:00:05 modem[1352]: <7> 292032 proto_init_config: proto=ncm 2023-08-29 00:00:03 modem[1114]: <7> 292032 proto_init_config: proto=3g 2023-08-29 00:00:00 time-settings[813]: <6> 279504 Service start 2023-08-29 00:00:00 led-controller[771]: <6> 288051 Start to run STATUS_SAN 1969-12-31 21:00:17 led-controller[771]: <6> 288504 Service start


[ 0.000000] Linux version 5.4.154 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16325-88151b8303)) #0 SMP Sun Oct 24 09:01:35 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TP-Link Archer C6U v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] percpu: Embedded 14 pages/cpu s26768 r8192 d22384 u57344 [ 0.000000] pcpu-alloc: s26768 r8192 d22384 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00000809 [ 0.000000] Readback ErrCtl register=00000809 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 120964K/131072K available (6089K kernel code, 210K rwdata, 748K rodata, 1260K init, 238K bss, 10108K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from 0x806e5a3c with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000008] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007812] Calibrating delay loop... 583.68 BogoMIPS (lpj=1167360) [ 0.042006] pid_max: default: 32768 minimum: 301 [ 0.046776] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.054001] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.064389] rcu: Hierarchical SRCU implementation. [ 0.069813] smp: Bringing up secondary CPUs ... [ 0.075937] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.075949] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.075961] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.076062] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.102556] Synchronize counters for CPU 1: done. [ 0.143441] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.143451] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.143459] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.143515] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.167288] Synchronize counters for CPU 2: done. [ 0.198673] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.198682] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.198691] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.198753] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.225150] Synchronize counters for CPU 3: done. [ 0.255031] smp: Brought up 1 node, 4 CPUs [ 0.263557] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.273255] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.280263] pinctrl core: initialized pinctrl subsystem [ 0.287161] NET: Registered protocol family 16 [ 0.298157] FPU Affinity set after 4688 emulations [ 0.314457] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.325666] clocksource: Switched to clocksource GIC [ 0.332485] thermal_sys: Registered thermal governor 'step_wise' [ 0.332991] NET: Registered protocol family 2 [ 0.343413] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.351710] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.360081] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.367700] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.374675] TCP: Hash tables configured (established 1024 bind 1024) [ 0.381112] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.387590] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.394777] NET: Registered protocol family 1 [ 0.399103] PCI: CLS 0 bytes, default 32 [ 0.493638] 4 CPUs re-calibrate udelay(lpj = 1163264) [ 0.500267] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.512732] random: fast init done [ 0.519447] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.525231] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.536450] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.545507] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.551381] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.557198] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.563627] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.573793] printk: console [ttyS0] disabled [ 0.578075] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.587063] printk: console [ttyS0] enabled [ 0.595323] printk: bootconsole [early0] disabled [ 0.607694] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.623312] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 0.628183] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.634529] Creating 5 MTD partitions on “spi0.0”: [ 0.639326] 0x000000000000-0x000000040000 : “u-boot” [ 0.645682] 0x000000040000-0x000000fa0000 : “firmware” [ 0.652267] 2 uimage-fw partitions found on MTD device firmware [ 0.658216] Creating 2 MTD partitions on “firmware”: [ 0.663186] 0x000000000000-0x000000250000 : “kernel” [ 0.669388] 0x000000250000-0x000000f60000 : “rootfs” [ 0.675558] mtd: device 3 (rootfs) set to be root filesystem [ 0.681332] 1 squashfs-split partitions found on MTD device rootfs [ 0.687532] 0x0000005f0000-0x000000f60000 : “rootfs_data” [ 0.694245] 0x000000fa0000-0x000000fb0000 : “config” [ 0.700487] 0x000000fb0000-0x000000ff0000 : “tplink” [ 0.706768] 0x000000ff0000-0x000001000000 : “radio” [ 0.714117] libphy: Fixed MDIO Bus: probed [ 0.744026] libphy: mdio: probed [ 0.747512] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.757000] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 0.767693] mt7621-pci 1e140000.pcie: Parsing DT failed [ 0.775687] NET: Registered protocol family 10 [ 0.781554] Segment Routing with IPv6 [ 0.785411] NET: Registered protocol family 17 [ 0.789966] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.803139] 8021q: 802.1Q VLAN Support v1.8 [ 0.809796] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.825581] libphy: dsa slave smi: probed [ 0.830120] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 0.839752] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 0.849465] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] [ 0.859151] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] [ 0.868880] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] [ 0.878699] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 0.889939] DSA: tree 0 setup [ 0.893239] rt2880-pinmux pinctrl: pcie is already enabled [ 0.898894] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 0.906476] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.013635] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.019216] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.124470] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.131425] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.136300] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.141180] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.150658] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.157030] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.163900] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.170769] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.176299] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.182333] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.188597] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.194928] pci 0000:00:00.0: supports D1 [ 1.198940] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.205093] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.211139] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.217403] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.223726] pci 0000:00:01.0: supports D1 [ 1.227738] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.234942] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.242954] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.251159] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000 [ 1.257213] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 1.263613] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.271151] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.276389] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.282481] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.289261] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.296480] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.303324] pci 0000:02:00.0: [14c3:7663] type 00 class 0x000280 [ 1.309392] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.316624] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.323854] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.331191] pci 0000:02:00.0: supports D1 D2 [ 1.335463] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.342105] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 1.357320] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.362565] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.368653] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.375435] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.382652] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.389303] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.395911] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.402868] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.409472] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.416429] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.423215] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 1.430431] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 1.437213] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x604fffff pref] [ 1.444430] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff] [ 1.451218] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff] [ 1.458012] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 1.464793] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 1.471582] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff] [ 1.478369] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.483333] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 1.490115] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.496894] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 1.504117] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff 64bit pref] [ 1.511867] pci 0000:02:00.0: BAR 2: assigned [mem 0x60400000-0x60403fff 64bit pref] [ 1.519615] pci 0000:02:00.0: BAR 4: assigned [mem 0x60404000-0x60404fff 64bit pref] [ 1.527360] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.532324] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 1.539106] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 1.545889] pci 0000:00:01.0: bridge window [mem 0x60300000-0x604fffff pref] [ 1.553929] hctosys: unable to open rtc device (rtc0) [ 1.563554] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 1.575126] Freeing unused kernel memory: 1260K [ 1.579706] This architecture does not have kernel memory protection. [ 1.586149] Run /sbin/init as init process [ 1.590928] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off [ 2.092174] init: Console is alive [ 2.095851] init: - watchdog - [ 2.845479] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.933151] usbcore: registered new interface driver usbfs [ 2.938801] usbcore: registered new interface driver hub [ 2.944239] usbcore: registered new device driver usb [ 2.958836] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator [ 2.967850] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 2.973189] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 2.985809] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 2.995001] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 3.000960] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 3.006288] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 3.013777] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 3.021177] hub 1-0:1.0: USB hub found [ 3.025073] hub 1-0:1.0: 2 ports detected [ 3.030062] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.039091] hub 2-0:1.0: USB hub found [ 3.042966] hub 2-0:1.0: 1 port detected [ 3.052927] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.070083] init: - preinit - [ 3.688170] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 3.696486] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 3.704953] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.854252] random: jshn: uninitialized urandom read (4 bytes read) [ 3.919141] random: jshn: uninitialized urandom read (4 bytes read) [ 3.966727] random: jshn: uninitialized urandom read (4 bytes read) [ 4.221955] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 4.228965] 8021q: adding VLAN 0 to HW filter on device lan1 [ 8.519224] jffs2: notice: (624) jffs2_build_xattr_subsystem: complete building xattr subsystem, 97 of xdatum (84 unchecked, 13 orphan) and 143 of xref (15 dead, 0 orphan) found. [ 8.544424] mount_root: switching to jffs2 overlay [ 8.554422] overlayfs: upper fs does not support tmpfile. [ 8.570375] urandom-seed: Seeding with /etc/urandom.seed [ 8.770686] procd: - early - [ 8.775274] procd: - watchdog - [ 9.333845] procd: - watchdog - [ 9.338363] procd: - ubus - [ 9.499619] procd: - init - [ 9.713743] random: crng init done [ 9.717158] random: 7 urandom warning(s) missed due to ratelimiting [ 10.323085] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.344080] tun: Universal TUN/TAP device driver, 1.6 [ 10.364618] GACT probability on [ 10.369080] Mirror/redirect action on [ 10.373010] urngd: v1.0.2 started. [ 10.384948] u32 classifier [ 10.387731] input device check on [ 10.391391] Actions configured [ 10.411984] Loading modules backported from Linux version v5.10.68-0-g4d8524048a35 [ 10.419595] Backport generated by backports.git v5.10.68-1-0-ga4f9ba32 [ 10.467840] xt_time: kernel timezone is -0000 [ 10.523243] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 10.528694] pci 0000:00:00.0: enabling device (0004 → 0007) [ 10.534357] mt7603e 0000:01:00.0: enabling device (0000 → 0002) [ 10.540549] mt7603e 0000:01:00.0: ASIC revision: 76030010 [ 11.162948] mt7603e 0000:01:00.0: Firmware Version: ap_pcie [ 11.168541] mt7603e 0000:01:00.0: Build Time: 20160107100755 [ 11.201666] mt7603e 0000:01:00.0: firmware init done [ 11.383475] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 11.394613] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 11.400076] pci 0000:00:01.0: enabling device (0004 → 0007) [ 11.405779] mt7615e 0000:02:00.0: enabling device (0000 → 0002) [ 11.423563] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 11.449312] PPP generic driver version 2.4.2 [ 11.455131] NET: Registered protocol family 24 [ 11.476516] kmodloader: done loading kernel modules from /etc/modules.d/* [ 13.152792] mt7615e 0000:02:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin [ 13.291455] mt7615e 0000:02:00.0: HW/SW Version: 0x65322d31, Build Time: 19091404338b809 [ 13.291455] [ 13.425257] mt7615e 0000:02:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20190914043434 [ 13.433857] mt7615e 0000:02:00.0: Region number: 0x3 [ 13.438919] mt7615e 0000:02:00.0: Parsing tailer Region: 0 [ 13.447313] mt7615e 0000:02:00.0: Region 0, override_addr = 0x00112c00 [ 13.453912] mt7615e 0000:02:00.0: Parsing tailer Region: 1 [ 13.460536] mt7615e 0000:02:00.0: Parsing tailer Region: 2 [ 13.466482] mt7615e 0000:02:00.0: override_addr = 0x00112c00, option = 3 [ 18.238989] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 18.257113] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 18.265410] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 18.272420] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 18.282166] 8021q: adding VLAN 0 to HW filter on device lan1 [ 18.290882] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 18.298340] br-lan: port 1(lan1) entered blocking state [ 18.303668] br-lan: port 1(lan1) entered disabled state [ 18.310168] device lan1 entered promiscuous mode [ 18.314878] device eth0 entered promiscuous mode [ 18.340596] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 18.347853] 8021q: adding VLAN 0 to HW filter on device lan2 [ 18.357865] br-lan: port 2(lan2) entered blocking state [ 18.363175] br-lan: port 2(lan2) entered disabled state [ 18.370538] device lan2 entered promiscuous mode [ 18.386592] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 18.393890] 8021q: adding VLAN 0 to HW filter on device lan3 [ 18.403008] br-lan: port 3(lan3) entered blocking state [ 18.408387] br-lan: port 3(lan3) entered disabled state [ 18.415359] device lan3 entered promiscuous mode [ 18.433468] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 18.441871] 8021q: adding VLAN 0 to HW filter on device lan4 [ 18.451560] br-lan: port 4(lan4) entered blocking state [ 18.456850] br-lan: port 4(lan4) entered disabled state [ 18.464340] device lan4 entered promiscuous mode [ 18.490476] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 18.497614] 8021q: adding VLAN 0 to HW filter on device wan [ 21.285948] br-lan: port 5(wlan1) entered blocking state [ 21.291335] br-lan: port 5(wlan1) entered disabled state [ 21.297126] device wlan1 entered promiscuous mode [ 23.813444] wlan1: authenticate with 00:5f:67:9a:52:27 [ 23.855472] wlan1: send auth to 00:5f:67:9a:52:27 (try 1/3) [ 23.868301] wlan1: authenticated [ 23.873722] wlan1: associate with 00:5f:67:9a:52:27 (try 1/3) [ 23.886608] wlan1: RX AssocResp from 00:5f:67:9a:52:27 (capab=0x11 status=0 aid=1) [ 23.904723] wlan1: associated [ 23.990977] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 23.997836] br-lan: port 5(wlan1) entered blocking state [ 24.003163] br-lan: port 5(wlan1) entered listening state [ 32.037659] br-lan: port 5(wlan1) entered learning state [ 40.229662] br-lan: port 5(wlan1) entered forwarding state [ 97.190173] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 97.197713] br-lan: port 2(lan2) entered blocking state [ 97.202966] br-lan: port 2(lan2) entered listening state [ 98.213953] mt7530 mdio-bus:1f lan2: Link is Down [ 98.218780] br-lan: port 2(lan2) entered disabled state [ 107.430087] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 107.437623] br-lan: port 2(lan2) entered blocking state [ 107.442874] br-lan: port 2(lan2) entered listening state [ 108.453931] mt7530 mdio-bus:1f lan2: Link is Down [ 108.458763] br-lan: port 2(lan2) entered disabled state [ 110.502089] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 110.509623] br-lan: port 2(lan2) entered blocking state [ 110.514875] br-lan: port 2(lan2) entered listening state [ 112.549931] mt7530 mdio-bus:1f lan2: Link is Down [ 112.554761] br-lan: port 2(lan2) entered disabled state [ 124.838112] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 124.845681] br-lan: port 2(lan2) entered blocking state [ 124.850902] br-lan: port 2(lan2) entered listening state [ 126.583252] br-lan: topology change detected, sending tcn bpdu [ 126.589151] br-lan: port 5(wlan1) entered blocking state [ 132.901675] br-lan: port 2(lan2) entered learning state [ 140.197933] mt7530 mdio-bus:1f lan2: Link is Down [ 140.202763] br-lan: port 2(lan2) entered disabled state [ 140.208152] br-lan: port 5(wlan1) entered listening state [ 148.261675] br-lan: port 5(wlan1) entered learning state [ 156.453702] br-lan: port 5(wlan1) entered forwarding state [ 581.478222] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 581.485763] br-lan: port 1(lan1) entered blocking state [ 581.491011] br-lan: port 1(lan1) entered listening state [ 589.605717] br-lan: port 1(lan1) entered learning state [ 597.797718] br-lan: port 1(lan1) entered forwarding state [ 597.803116] br-lan: topology change detected, sending tcn bpdu [ 819.046021] mt7530 mdio-bus:1f lan1: Link is Down [ 819.051103] br-lan: port 1(lan1) entered disabled state [ 827.238166] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 827.245731] br-lan: port 1(lan1) entered blocking state [ 827.250955] br-lan: port 1(lan1) entered listening state [ 835.365744] br-lan: port 1(lan1) entered learning state [ 843.557744] br-lan: port 1(lan1) entered forwarding state [ 843.563145] br-lan: topology change detected, sending tcn bpdu [ 4757.350453] mt7530 mdio-bus:1f lan1: Link is Down [ 4757.355568] br-lan: port 1(lan1) entered disabled state [ 4773.734579] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 4773.742116] br-lan: port 1(lan1) entered blocking state [ 4773.747368] br-lan: port 1(lan1) entered listening state [ 4781.862158] br-lan: port 1(lan1) entered learning state [ 4788.070433] mt7530 mdio-bus:1f lan1: Link is Down [ 4788.075264] br-lan: port 1(lan1) entered disabled state [ 4791.142578] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 4791.150109] br-lan: port 1(lan1) entered blocking state [ 4791.155363] br-lan: port 1(lan1) entered listening state [ 4799.270159] br-lan: port 1(lan1) entered learning state [ 4807.462160] br-lan: port 1(lan1) entered forwarding state [ 4807.467561] br-lan: topology change detected, sending tcn bpdu [ 4859.750441] mt7530 mdio-bus:1f lan1: Link is Down [ 4859.755345] br-lan: port 1(lan1) entered disabled state


Space for additional notes, links to forum threads or other resources.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/07/23 20:08
  • by frollic