Linksys WRT54G/GL/GS GPIO

Please cf. the generic wikipage for port.gpio Please also cf. soc for some of the supportd SoCs

GPIO pins, eh? The integrated Broadcom CPU BCM4712 used in the WRT54G provides a number of General Purpose Input/Output pins (or GPIO pins) that are used for various purposes in the router. We have been able to identify 8 such pins until now and these are assigned as follows:

Pin Direction v2.2 Name v3.0+ Name SD Card Name
GPIO 0 (Output) WLAN LED Unknown Not used
GPIO 1 Output POWER LED POWER LED Not used
GPIO 2 Output ADM_EECS WHITE LED DI (only v4.0+/WRT54GL)
GPIO 3 Output ADM_EESK AMBER LED CLK
GPIO 4 Input ADM_EEDO FRONT BUTTON DO
GPIO 5 Output ADM_EEDI Unknown, robo_reset? DI (only up to v3.1)
GPIO 6 Input Reset button Reset? Not used
GPIO 7 Output DMZ LED DMZ LED CS

On WRT54G v2.2 the ADM_* pins constitute an interface used to configure the ADMTek switch chip. Since this only happens during the boot process, we are free to use these pins to our likings afterwards (the corresponding pins on the switch chip will be tri-state after configuration). The names of the other pins should be self explanatory. The direction of the pins can be individually programmed (even though this of course does not make sense for every pin).

More information on the Fully hacked WRT54G and Adding a SD card to your WRT54G pages.

Kamikaze 7.07 and later now includes a kmod-broadcom-mmc package for WRT54G but it does not have as good compatibility as the optimized driver, mentioned below.

ipkg install kmod-broadcom-mmc

There is also an optimized version with better best card compatibility than the original mmc.o module. It's recommended if the Kamikaze package is not working. Althought it's made for White Russian, it seems to work fine with Kamikaze based on kernel 2.4.

tar zxvf mmc-v1.3.4-gpio2.tgz
cp mmc-v1-3.4-gpio2/mmc.o /lib/modules/2.4.34/

Configure the gpiomask (see below for correct value) and load the mmc module. Verify that it loaded correctly by checking the dmesg log.

echo 0x9c > /proc/diag/gpiomask
insmod mmc
dmesg

If the unit locks up, make sure the set the correct gpiomask before loading the driver. The gpiomask value can be found by adding up all the hex values in the following table:

GPIO PIN 0 0x01
GPIO PIN 1 0x02
GPIO PIN 2 0x04
GPIO PIN 3 0x08
GPIO PIN 4 0x10
GPIO PIN 5 0x20
GPIO PIN 6 0x40
GPIO PIN 7 0x80
GPIO PIN 8 0x100
GPIO PIN 9 0x200
GPIO PIN 10 0x400
GPIO PIN 11 0x800
GPIO PIN 12 0x1000
GPIO PIN 13 0x2000
GPIO PIN 14 0x4000
GPIO PIN 15 0x8000

E.g. for WRT54GL that is using GPIO line 2, 3, 4, and 7:

  • Hex values: 0x04 + 0x08 + 0x10 + 0x80 = 0x9c

Use squarebox.co.uk online hex calculator or similar to add up the values.

This is one very cool mod! Credit goes to kiel.kool.dk (seems to be down, web.archive.org mirror) for this awesome work. They have also pioneered some other interesting mods as well. Check out http://duff.dk/wrt54gs/ for info. They created this mod for the wrt54g version 2, then I (INH) ported it to version 3. If you have another version, you are going to have to figure out how to port it.. but it shouldn't be too hard.

This mod allows you to read and write from a MMC/SD card (including miniSD and microSD) in SPI mode. This is awesome as it can literally give you 555 time the storage space. You can now have over one gigabyte of memory to store and run programs from, store packet logs, etc etc.. It's not a very hard mod to do, unless you have something other than a wrt54g version 2 or 3. If thats the case, please read on, as I go over how I ported this mod to my version 3.

1. CS - Chip Select for the SD card GPIO 7 (0x80)
2. DI - Data in on the SD card. GPIO 5 (0x20) / GPIO 2 (0x04) *
3. VSS - Ground is a good thing GND
4. VDD - We need power of course. 3.3 V will do the job 3.3 V
5. CLK - The clock we generate for the SD card GPIO 3 (0x08)
6. VSS2 - Another ground is also a good thing GND (Not on microSD)
7. DO - Data out from the SD card GPIO 4 (0x10)

* GPIO 5 was used for WRT54G version up to v3.1 and GPIO 2 for WRT54G v4.0 and later, including WRT54GL. Other units may have a different layout.

The following is the guide from kiel.kool.dk (web.archive.org mirror) by Rasmus Rohde and Mads Ulrik Kristoffersenon about installing an MMC/SD card reader/writer in a wrt54g version 2, with added commentary where I feel is appropriate

I added now comments for WRT HW-version 2.2 where the GPIO locations are different, but the general procedure is the same.

This project is for people who would like to add a little storage to their Linksys WRT54G router besides the builtin 4MB flash ram. What we will do is connect an SD card reader to some of the GPIO pins of the CPU found inside the Linksys and with the help of a little driver we can use as a block device from Linux. This means that if you compile your kernel for the Linksys with e.g. support for MSDOS partitions and VFAT you will be able to mount, read, write, partition and so on your normal SD cards. The speed obtainable for reading and writing seems to be about 200 KB/s.

Pictures

  • The insides of the router with SD card reader installed
  • attachment:kiel.kool.dk-AllSolderingDone.jpg
  • The finished product with SD card reader installed
  • attachment:kiel.kool.dk-Reuter_complete.jpg

What you need

  • A soldering iron and a bit of tin solder (and a little bit of soldering skills)
  • An SD card reader unless of course you want to solder directly on the card
  • (hint: mini-SD cards come with an adapter. You can solder to the adapter and use it as a socket)
  • 6 pieces of thin wire
  • A Linksys WRT54G (hardware version 2)

How to proceed

  1. For the SD card to work we need to attach 6 wires inside the router. This drawing of the SD card should give an idea of the pins that come into play:

1. CS - Chip Select for the SD card GPIO7
2. DI - Data in on the SD card. GPIO5
3. VSS - Ground is a good thing GND
4. VDD - We need power of course. 3.3V will do the job 3.3v
5. CLK - The clock we generate for the SD card GPIO3
6. VSS2 - Another ground is also a good thing GND
7. DO - Data out from the SD card GPIO4
  • We will be driving the SD card in SPI mode, meaning that only one of the four data out pins are used (pin 7). Obtaining the specs for driving the card in the native SD mode is VERY costly and furthermore the limited number of GPIO pins available inside the router also mandates the use of some sort of serial protocol. The two VSS pins can simply be wired together for this project (VSS2 is used to control the sleep mode of the card). With this in mind lets look at the solder points in the router.
  1. The first three solder points are located at RP3
  2. The next two solder points are located at JP1
  3. The last solder point is at the DMZ LED

Proceed by soldering a wire to each of the 6 solder points. Pay special attention not to short circuit the pins of RP3 - even though these solder points were chosen because they provide the most spacious access point to the GPIO lines needed, it's still pretty tight quarters, so watch out!

  1. By now the wires should be attached nicely inside the router, so that we may continue to connect them to the SD card (reader). This picture shows the SD card reader. It is pretty easy to solder on that one.
  2. Mount the card reader somewhere inside your router. We chose the right hand side of the top cover, using double sided duct tape to make it stick and drilled a small slot to allow cards to be inserted and removed with the cover closed. See the picture links at the top of the page to see what this looks like and check this picture of the actual hole.
  3. That was easy. We are now ready for the software part.

Software

  • This section is obsolete, see driver section for driver installation.

First of all we suggest that you configure a kernel with support for MSDOS partitions and VFAT. Partition support must be built into the kernel whereas VFAT can be built both as a module or into the kernel. These are some things you may want to include in your .config:

CONFIG_PARTITION_ADVANCED=y
CONFIG_MSDOS_PARTITION=y
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y

Now get the driver and the Makefile. You will need to modify the Makefile to point to where your OpenWRT linux kernel headers are and also the mipsel compiler location. When that is done just type make (ignore the warnings - they are OK). But you may just as well install the freifunk-sdcard and freifunk-sdinit mmc module packages which work fine on my whiterussian RC5.

The module is now ready to be inserted. Make sure a card is placed in the reader and then load the module. Check with dmesg that everything went OK, and hopefully you should now have some new devices in /dev/mmc/... Here is a little snippet of a “conversation” with the router

root@radio:~# ls -al /lib/modules/2.4.20/
drwxr-xr-x    1 root     root            0 Jan  1 00:08 .
drwxr-xr-x    1 root     root            0 Jan  1 00:01 ..
lrwxrwxrwx    1 root     root           28 Jan  1 00:01 et.o -> /rom/lib/modules/2.4.20/et.o
-rw-r--r--    1 root     root        50616 Jan  1 00:02 fat.o
-rw-r--r--    1 root     root        12780 Jan  1 00:08 mmc.o
-rw-r--r--    1 root     root        11244 Jan  1 00:03 msdos.o
-rw-r--r--    1 root     root        19156 Jan  1 00:05 vfat.o
lrwxrwxrwx    1 root     root           28 Jan  1 00:01 wl.o -> /rom/lib/modules/2.4.20/wl.o
root@radio:~# insmod mmc
Using /lib/modules/2.4.20/mmc.o
root@radio:~# dmesg | tail -7
mmc Hardware init
mmc Card init
mmc Card init *1*
mmc Card init *2*
Size = 249856, hardsectsize = 512, sectors = 499712
Partition check:
 mmca: p1
root@radio:~# insmod fat
Using /lib/modules/2.4.20/fat.o
root@radio:~# insmod msdos
Using /lib/modules/2.4.20/msdos.o
root@radio:~# mount -t msdos /dev/mmc/disc0/part1 /mnt
root@radio:~# ls -al /mnt
drwxr-xr-x    2 root     root        16384 Jan  1  1970 .
drwxr-xr-x    1 root     root            0 Jan  1 00:01 ..
-rwxr-xr-x    1 root     root            0 Jan  1 00:07 bossepr0.pic
-rwxr-xr-x    1 root     root        22646 Jan  1 00:02 ld-uclib.so
-rwxr-xr-x    1 root     root        12780 Jan  1  2000 mmc.o
-rwxr-xr-x    1 root     root      1048576 Jan  1  2000 temp.bin
-rwxr-xr-x    1 root     root     16777216 Jan  1  2000 temp2.bin
-rwxr-xr-x    1 root     root     16777216 Jan  1  2000 temp3.bin
-rwxr-xr-x    1 root     root          693 Jan  1  2000 temp4.bin
root@radio:~# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/root                  896       896         0 100% /rom
/dev/mtdblock/4           2176      1580       596  73% /
/dev/mmc/disc0/part1    249728     33856    215872  14% /mnt

Using OpenWRT RC5 no msdos kernel module is needed. The mount-option -tmsdos has to be omitted.

A little help with kernel compilation

The easiest way to get a kernel running with the needed fs support is probably by downloading OpenWRT and building the flash image. When you are familiar with this process, it is quite easy to change the settings for your kernel. Just go to buildroot/build_mipsel/linux and type make menuconfig. Go to file systems → Partition Types and check “Advanced partition selection” and “PC BIOS (MSDOS partition tables) support”. In “File systems” you should also check “DOS FAT fs support” and optionally “VFAT (Windows 95) fs support”. When done just exit saving the changed and type make dep zImage to force a rebuild of the kernel. Then you can just rebuild your OpenWRT image and the new kernel will be included automatically. GPIO pins, eh?

The integrated Broadcom CPU BCM4712 used in the WRT54G provides a number of General Purpose Input/Output pins (or GPIO pins) that are used for various purposes in the router. We have been able to identify 8 such pins until now and these are assigned as follows:

Pin Direction Name
GPIO 0 (Output) WLAN LED
GPIO 1 Output POWER LED
GPIO 2 Output ADM_EECS
GPIO 3 Output ADM_EESK
GPIO 4 Input ADM_EEDO
GPIO 5 Output ADM_EEDI
GPIO 6 Input Reset button
GPIO 7 Output DMZ LED

The pins used in this project are the ADM_EESK, ADM_EEDO, ADM_EEDI and DMZ LED pins. The ADM_* pins constitute an interface used to configure the ADMTek switch chip. Since this only happens during the boot process, we are free to use these pins to our likings afterwards (the corresponding pins on the switch chip will be tri-state after configuration). The names of the other pins should be self explanatory. The direction of the pins can be individually programmed (even though this of course does not make sense for every pin).

Important note for v2 hardware and some WRT54GS: It is worth double-checking the GPIO pin allocations on RP3. The picture above was not correct for my V2 WRT54G. The CLK and DO, which are GPIO3 and GPIO4, were swapped compared to the picture.

Further unverified evidence supports that the wrt54gs v1.1 hardware also has gpio 3 and 4 switched. Can definitely confirm this swapped CLK/DO for my WRT54GS V1.0, so it's likely that the V1.1 statement before is correct, too) I soldered to the right-hand side of RP3 as shown in the picture with GPIO5 (DI) at the bottom, GPIO4 (DO) next up and GPIO3 (CLK) up from that.

A good way to test the pin allocations is with the gpio utility and a script to toggle the GPIO pin periodically, then search for the pin with a digital multimeter or oscilloscope probe. I toggled the pins with the following single line in the shell (example for GPIO 5):

 while true; do gpio enable 5; sleep 1; gpio disable 5; sleep 1; done

I then used my multimeter to detect the pin toggling between 0V and 3.3V every second. I seriously recommend that you do this to verify which pins you are working on prior to doing any soldering.

On a WRT54G Version 2 the tests on GPIO4 failed. According to http://forum.openwrt.org/viewtopic.php?pid=31968 the reason is an incomplete initialization of the GPIOs. Using the mmc.o downloadable at the end of the thread the MMC is detected and working, the GPIO test is also working after loading this module.

For v2.2 hardware:

GPIO 3 can be found on Pin 3 of RP4 (near the BCM switch IC), just left of it you can find GPIO 5 next to the RA10 Text label. GPIO 4 is located near the RA13 Text label (near to the Power LED)

linuxbench.org-wrt54gs.jpg

This is a picture of the GPIO 3+5 for WRT54G v2.2 taken from http://linuxbench.org

*to be written, in the meantime you can find version 3 info here.

Basically the same as above, but different GPIO points on the board.

Power - 3.3v (red), and GND (black). I looped through the board for strength of connection:

otago.ac.nz-power.jpg

GPIO 3, as mentioned in the URL above, on the right hand side of the amber LED:

otago.ac.nz-button.jpg

GPIO 4 and 7:

otago.ac.nz-underside.jpg

GPIO 5 - definitely right next to the “RA10” label:

otago.ac.nz-gpio5.jpg

Picture taken from otago.ac.nz.

Almost the same as for version 3, except GPIO 5 seems to be missing from the board, so use GPIO 2 instead and edit the driver accordingly. Here is more version 4 info someone has made available, including pictures and modified driver source and binary. Sadly this link is dead, so you currently have to use the wayback machine to see where to solder the cables. that site from web.archive.org.

Or, use the newer optimized mmc driver for GPIO2 in the driver section above.

+3.3V and GND:

GPIO 2 and 3:

GPIO 4 and 7:

Pictures taken from cascade.dyndns.org.

Here is another mod done for a WRT54GS v4, essentially same as for WRTG54 v4 and WRTG54GL.

theattic.thruhere.net-gpio47.jpg

theattic.thruhere.net-gpio23.jpg

theattic.thruhere.net-vddvss.jpg

theattic.thruhere.net-complete.jpg

Buffalo WHR-HP-G54 connections are:

GPIO3 Output (uninstalled LED) to CLK (SD Card #5) Connect to the very small pad above “R4” in the picture.
GPIO6 Output (AOSS LED) to DO (SD Card #2) Connect to the bottom of the resistor in the picture.
GPIO7 Output (Diag LED) to CS (SD Card #1) Connect to the left side of the resistor shown in the picture.

flatsurface.com-whr-sdcard1.jpg

GPIO5 Input (Bridge/Auto switch) to DI (SD Card #7) Connect to the C242 on the side nearest R151 in the picture. The switch must remain in the “auto” position for proper operation.
3.3v (near voltage regulator) to Vcc (SD Card #4)Connect to the pad shown in the picture.
GND (Bridge/Auto switch frame) to Gnd (SD Card #3&6) Available in many places - the frame of the switch is convenient.

flatsurface.com-whr-sdcard2.jpg

echo 0xe8 > /proc/diag/gpiomask to avoid hotplug problems.

Linksys WAP54 v3.1}} Here is a link that describes how to add a SD card to a WAP54G v31 (EU), this project uses the card read only, first a cramfs is created on the card with the PC (this is the native system the Linksys software uses), so no MSDOS stuff needs to be added to the kernel (there is only 2MB FLASH in WAP54G v31 EU). http://panteltje.com/panteltje/wap54g/to-linksys-wap54g-forum-2.txt

This is another howto for wap54g...

It uses optimized mmc v1.3.4

gpio:3,4,6,7

filesystem: ext2, vfat

max cardsize: 2GB

http://linksys.chyl.org/readarticle.php?article_id=1

I read on several websites, that some people managed to wire a SD Card (or a MMC) to a Fonera access point. I run into one issue so I decided to describe the process here.

Solder the SD Card

The first step, is to locate the SW pins (near the antenna).. simply solder some wires like this:

SD Card              Fonera
DO  (pin 7)          SW1
CLK (pin 5)          SW2
DI  (pin 2)          SW5
CS  (pin 1)          SW6
Gnd (pin 3)          Gnd
Vcc (pin 4)          Vcc

jkx.larsen-b.com-dsc02584_2.sized.jpg

You can solder the VCC, and Gnd on the serial pins.

Unsolder the Caps

In my first tests, I discovered the SD card is detected, so I checked the signals. And discover the clk isn’t really clear.. So I decided to remove the capacitor on the SPI bus. (C142, C143, C144, C145)

jkx.larsen-b.com-dsc02582.sized.jpg

Install software and test

Next we need to install the kernel module on OpenWRT. You can find it on the Phrozen website. Simply ipkg install the file and it should be ok. Now, let’s try: insert a SD Card, and reboot, you should see something like this in your log.

Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : MMC Driver for Fonera Version 2.5 (050507) -- '2B|!2B' (john@phrozen.org)
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : Card Found
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : card in op mode
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : SIZE : 241, nMUL : 6, COUNT : 1932, NAME : 256MB
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : Card Initialised
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : The inserted card has a capacity of 253231104 Bytes
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : adding disk
Jan  1 00:00:49 OpenWrt user.info kernel:  mmc1
Jan  1 00:00:49 OpenWrt user.warn kernel: mmc : Card was Found

So now you can mount it:

mount /dev/mmc0 /mnt

This stuff, is working really well, I managed to have around 150Ko/s (reading) which is far enough for my needs. The only issue right now, is that you need to carefully umount the card before removing it, otherwise the fonera will crash.

Project page

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2018/06/01 12:42
  • by tmomas