User Tools

Site Tools


toh:gl.inet:gl.inet_gl-ar300m

GL.iNet GL-AR300M

WARNING – Do not upgrade pre-release versions of ath79 firmware to GL-AR300M (NAND) images

Versions of ath79 firmware for the GL-AR300M prior to November 15, 2019 are not capable of reliably upgrading directly to the new GL-AR300M (NAND) images.

Upgrade with U-Boot is recommended. U-Boot can be accessed without a serial connection. See https://docs.gl-inet.com/en/3/troubleshooting/debrick/

Direct upgrades may result in the device unexpectedly booting into the “old” NAND-resident system and its configuration. If this is a “stock” OEM system, its default LAN IP is 192.168.8.1.

If the NAND-resident system fails to boot, use U-Boot to install a fresh image.

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.

FIXME Any text with a light background (like this one) provides instructions for creating the Details Page. When you have filled in correct/useful information (instead of any template that's there) remove the instructions, as well as the <WRAP> that encloses it.

Generic Router

FIXME

Getting started with a new Device Page

  1. This is an empty template that suggests the information that should be present on a well-constructed Device Page. This means, that you have to fill it with life and information.
  2. There are several “fixme” tags with text on a light background (like this text) throughout this template. As you fill in the page, remove those tags so that people can judge its completeness.
  3. When there are no more “fixme” tags left, delete this one too, along with the <WRAP> that encloses it.

Keep the articles modular

  • Please include only model specific information, omit bla,bla and put everything generic into separate articles
  • If you have no time to write certain stuff, link to docs
  • base-system should lead the way, do not explain this again
  • DO NOT provide a complete howto here! Instead groom the general documentation.

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
GL-AR300Mv1.4.0Qualcomm Atheros QCA953165016, 128NAND128Qualcomm Atheros QCA9531b/g/n-2--1x 2.0

Installation

Flash Layout

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

OEM easy installation

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

  • Browse to http://192.168.1.1/Upgrade.asp
  • Upload .bin file to router
  • Wait for it to reboot
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

OEM installation using the TFTP method

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

Upgrading OpenWrt

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

Switch Ports (for VLANs)

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2
LAN 3 EXAMPLE 1
LAN 4 EXAMPLE 0

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The GL.iNet GL-AR300M has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

Hardware

Info

General
Brand GL.iNet
Model GL-AR300M
Versions v1.4.0
Device Type WiFi Router
Availability Available 2020
Comments - general Flashing to the 128MB NAND flash is supported in Snapshot ath79 at time of writing, removable external antennas on "ext" variant
OpenWrt Support
Supported Since Commit https://git.lede-project.org/?p=source.git;a=commit;h=d963ddf0424a551e5fadd561c934bfdb5d198764
Supported Since Release 17.01.0
Supported Current Release 19.07.3
Unsupported
Hardware
Bootloader U-Boot
Target ar71xx-ath79
System-On-Chip
CPU MHz 650
Flash MB 16, 128NAND
RAM MB 128
Network
Ethernet 100M ports 2
Ethernet Gbit ports -
Switch Qualcomm Atheros QCA9531
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz -
WLAN Hardware Qualcomm Atheros QCA9531
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 1x 2.0
SATA ports -
Serial Yes
JTAG No
Comments - USB & SATA ports
Misc
LED count 3
Button count 2
Power supply 5 VDC, 1.0 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/GL.iNet_AR300M
OEM device homepage URL https://www.gl-inet.com/products/gl-ar300m/
Firmware OEM Stock URL https://www.gl-inet.com/firmware/ar300m/
Firmware OpenWrt Install URL http://downloads.openwrt.org/releases/19.07.3/targets/ar71xx/generic/openwrt-19.07.3-ar71xx-generic-gl-ar300m-squashfs-sysupgrade.bin
Firmware OpenWrt Upgrade URL http://downloads.openwrt.org/releases/19.07.3/targets/ar71xx/generic/openwrt-19.07.3-ar71xx-generic-gl-ar300m-squashfs-sysupgrade.bin
Edit the underlying data View/Edit data

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

  • To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for GL.iNet GL-AR300M @@Version@@
EXAMPLE 115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

Hardware mods

None so far.

Bootlogs

OEM bootlog

root@GL-AR300M:~# dmesg [ 0.000000] Linux version 4.9.120 (cc@cc-ubuntu1604) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7258-5eb055306f) ) #0 Thu Aug 16 07:51:15 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 80523834, node_mem_map 81000020 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=GL-AR300M console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(reserved),64k(art)ro;spi0.1:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 124164K/131072K available (3816K kernel code, 163K rwdata, 900K rodata, 232K init, 219K bss, 6908K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:650.000MHz, DDR:597.534MHz, AHB:216.666MHz, Ref:25.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008245] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.071108] pid_max: default: 32768 minimum: 301 [ 0.076083] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.083065] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.093358] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.103759] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.111441] NET: Registered protocol family 16 [ 0.117648] MIPS: machine is GL.iNet GL-AR300M [ 0.602626] ar724x-pci ar724x-pci.0: PCIe link is down [ 0.608084] registering PCI controller with io_map_base unset [ 0.631625] usbcore: registered new interface driver usbfs [ 0.637488] usbcore: registered new interface driver hub [ 0.643205] usbcore: registered new device driver usb [ 0.648819] PCI host bridge to bus 0000:00 [ 0.653189] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.660433] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.666313] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.673464] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.681840] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.685487] clocksource: Switched to clocksource MIPS [ 0.691950] NET: Registered protocol family 2 [ 0.697467] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.704823] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.711584] TCP: Hash tables configured (established 1024 bind 1024) [ 0.718405] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.724570] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.731462] NET: Registered protocol family 1 [ 0.736112] PCI: CLS 0 bytes, default 32 [ 0.738954] Crashlog allocated RAM at address 0x3f00000 [ 0.745661] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.759502] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.765682] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.786070] io scheduler noop registered [ 0.790205] io scheduler deadline registered (default) [ 0.796071] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.805301] console [ttyS0] disabled [ 0.829226] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.838331] console [ttyS0] enabled [ 0.845885] bootconsole [early0] disabled [ 0.860644] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.875771] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.880666] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.886797] Creating 4 MTD partitions on "spi0.0": [ 0.891748] 0x000000000000-0x000000040000 : "u-boot" [ 0.898850] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.906423] 0x000000050000-0x000000ff0000 : "reserved" [ 0.913742] 0x000000ff0000-0x000001000000 : "art" [ 0.921207] spi-nand: Giga SPI NAND was found. [ 0.925868] spi-nand: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 0.934106] 2 cmdlinepart partitions found on MTD device spi0.1 [ 0.940259] Creating 2 MTD partitions on "spi0.1": [ 0.945212] 0x000000000000-0x000000200000 : "kernel" [ 0.955677] 0x000000200000-0x000008000000 : "ubi" [ 1.385326] found bad block 7fe0000 [ 1.389676] libphy: Fixed MDIO Bus: probed [ 1.408986] libphy: ag71xx_mdio: probed [ 2.038083] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.048223] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.585480] random: fast init done [ 2.678029] ag71xx-mdio.1: Found an AR934X built-in switch [ 2.731340] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.737883] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.744621] ehci-pci: EHCI PCI platform driver [ 2.749426] usbcore: registered new interface driver usbtest [ 2.755327] usbcore: registered new interface driver usb_ehset_test [ 2.761895] usbcore: registered new interface driver lvs [ 2.769068] NET: Registered protocol family 10 [ 2.778652] NET: Registered protocol family 17 [ 2.783297] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.796822] 8021q: 802.1Q VLAN Support v1.8 [ 2.806799] UBI: auto-attach mtd5 [ 2.810263] ubi0: attaching mtd5 [ 7.021421] ubi0: scanning is finished [ 7.073773] ubi0: attached mtd5 (name "ubi", size 126 MiB) [ 7.079501] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.086607] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.093611] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.100808] ubi0: good PEBs: 1007, bad PEBs: 1, corrupted PEBs: 0 [ 7.107107] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 7.114562] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 453514400 [ 7.123907] ubi0: available PEBs: 0, total reserved PEBs: 1007, PEBs reserved for bad PEB handling: 19 [ 7.133598] ubi0: background thread "ubi_bgt0d" started, PID 332 [ 7.143301] block ubiblock0_0: created from ubi0:0(rootfs) [ 7.149038] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 7.156242] hctosys: unable to open rtc device (rtc0) [ 7.179120] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 7.187965] Freeing unused kernel memory: 232K [ 7.192553] This architecture does not have kernel memory protection. [ 8.112754] init: Console is alive [ 8.116634] init: - watchdog - [ 10.977920] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 11.378772] exFAT: Version 1.2.9 [ 11.423059] SCSI subsystem initialized [ 11.432366] ehci-platform: EHCI generic platform driver [ 11.437937] ehci-platform ehci-platform: EHCI Host Controller [ 11.444031] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 11.454354] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 11.485522] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 11.492213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.499260] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.506732] usb usb1: Product: EHCI Host Controller [ 11.511770] usb usb1: Manufacturer: Linux 4.9.120 ehci_hcd [ 11.517450] usb usb1: SerialNumber: ehci-platform [ 11.523153] hub 1-0:1.0: USB hub found [ 11.527356] hub 1-0:1.0: 1 port detected [ 11.534658] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 11.542631] ohci-platform: OHCI generic platform driver [ 11.550812] uhci_hcd: USB Universal Host Controller Interface driver [ 11.562228] usbcore: registered new interface driver usb-storage [ 11.570625] usbcore: registered new interface driver uas [ 11.576900] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 11.594827] init: - preinit - [ 12.944561] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.209869] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 429 [ 16.255468] random: procd: uninitialized urandom read (4 bytes read) [ 16.473825] UBIFS (ubi0:1): recovery needed [ 16.958395] UBIFS (ubi0:1): recovery completed [ 16.963096] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 16.971217] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.981481] UBIFS (ubi0:1): FS size: 110596096 bytes (105 MiB, 871 LEBs), journal size 5586944 bytes (5 MiB, 44 LEBs) [ 16.992452] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 16.999295] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID D28D484D-CAEA-4800-A518-90119CFB7AEF, small LPT model [ 17.041990] mount_root: switching to ubifs overlay [ 17.150994] urandom-seed: Seeding with /etc/urandom.seed [ 17.369623] procd: - early - [ 17.372705] procd: - watchdog - [ 18.039743] procd: - watchdog - [ 18.043243] procd: - ubus - [ 18.354794] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.519726] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.526784] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.534129] procd: - init - [ 21.338480] kmodloader: loading kernel modules from /etc/modules.d/* [ 21.631240] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 21.670119] tun: Universal TUN/TAP device driver, 1.6 [ 21.675346] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 21.720523] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 21.745896] Netfilter messages via NETLINK v0.30. [ 21.758269] ip_set: protocol 6 [ 21.865540] u32 classifier [ 21.868343] input device check on [ 21.872121] Actions configured [ 21.896834] Mirror/redirect action on [ 21.912426] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 21.999128] fuse init (API version 7.26) [ 22.021138] usbcore: registered new interface driver cdc_acm [ 22.027050] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 22.068076] usbcore: registered new interface driver cdc_wdm [ 22.087464] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 [ 22.095804] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 22.130971] ip_tables: (C) 2000-2006 Netfilter Core Team [ 22.138250] usbcore: registered new interface driver ipheth [ 22.314626] ctnetlink v0.93: registering with nfnetlink. [ 22.576416] usbcore: registered new interface driver usbserial [ 22.582521] usbcore: registered new interface driver usbserial_generic [ 22.589398] usbserial: USB Serial support registered for generic [ 22.624629] wireguard: WireGuard 0.0.20191012 loaded. See www.wireguard.com for information. [ 22.633421] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 22.771457] xt_time: kernel timezone is -0000 [ 22.786121] usbcore: registered new interface driver cdc_ether [ 22.804512] usbcore: registered new interface driver cdc_ncm [ 22.918764] usbcore: registered new interface driver cp210x [ 22.924614] usbserial: USB Serial support registered for cp210x [ 22.947339] usbcore: registered new interface driver huawei_cdc_ncm [ 23.089552] PPP generic driver version 2.4.2 [ 23.107301] PPP MPPE Compression module registered [ 23.120491] NET: Registered protocol family 24 [ 23.133838] usbcore: registered new interface driver qmi_wwan [ 23.153200] usbcore: registered new interface driver rndis_host [ 23.201672] usbcore: registered new interface driver sierra [ 23.207592] usbserial: USB Serial support registered for Sierra USB modem [ 23.231771] usbcore: registered new interface driver sierra_net [ 23.473396] usbcore: registered new interface driver option [ 23.479317] usbserial: USB Serial support registered for GSM modem (1-port) [ 23.507321] usbcore: registered new interface driver rt2800usb [ 23.535992] ath: EEPROM regdomain: 0x0 [ 23.536002] ath: EEPROM indicates default country code should be used [ 23.536005] ath: doing EEPROM country->regdmn map search [ 23.536020] ath: country maps to regdmn code: 0x3a [ 23.536025] ath: Country alpha2 being used: US [ 23.536029] ath: Regpair used: 0x3a [ 23.547152] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 23.551486] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 [ 23.562742] kmodloader: done loading kernel modules from /etc/modules.d/* [ 43.184865] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 43.192782] IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready [ 43.334165] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 43.677599] br-lan: port 1(eth1) entered blocking state [ 43.683008] br-lan: port 1(eth1) entered disabled state [ 43.688839] device eth1 entered promiscuous mode [ 43.741237] br-lan: port 1(eth1) entered blocking state [ 43.746705] br-lan: port 1(eth1) entered forwarding state [ 43.796273] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 44.665621] br-lan: port 1(eth1) entered disabled state [ 45.717631] eth1: link up (1000Mbps/Full duplex) [ 46.585814] br-lan: port 1(eth1) entered blocking state [ 46.591230] br-lan: port 1(eth1) entered forwarding state [ 52.261118] br-lan: port 2(wlan0) entered blocking state [ 52.266681] br-lan: port 2(wlan0) entered disabled state [ 52.272552] device wlan0 entered promiscuous mode [ 52.277535] br-lan: port 2(wlan0) entered blocking state [ 52.283021] br-lan: port 2(wlan0) entered forwarding state [ 52.353292] br-lan: port 2(wlan0) entered disabled state [ 60.255328] br-lan: port 2(wlan0) entered blocking state [ 60.260884] br-lan: port 2(wlan0) entered forwarding state [ 77.625225] random: crng init done [ 77.628762] random: 6 urandom warning(s) missed due to ratelimiting


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Space for additional notes, links to forum threads or other resources.

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/gl.inet/gl.inet_gl-ar300m.txt · Last modified: 2020/07/01 22:06 by ayewhy