User Tools

Site Tools


toh:gl-inet:gl-ar750s

GL.iNet GL-AR750S

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

A small, lightweight “travel router”, it features dual-band operation and supports 802.11ac. Other notable features include a built-in microSD interface (vendor states support up to 128 GB), USB 2.0, and internal access to I2C, UART, and various GPIO. Power is supplied through a micro-USB socket. The unit has two external antennas that “fold” for compactness. Vendor states 100mmX68mmX24mm, 86g (very roughly 4“x3”x1“).

Vendor advertises 17 Mbps for OpenVPN and 68 Mbps for WireGuard in August, 2018. Vendor states “OpenWrt Pre-installed” (though likely not a “stock” build).

Announced in July, 2018, this is an “updated” version of the GL.iNet GL-AR750. Significant changes include the use of GigE interfaces.

Vendor specifications, including annotated board photos, are presently available at https://docs.gl-inet.com/en/3/hardware/ar750s/

Initial support in OpenWRT master with commit ar71xx: add support for GL.iNet GL-AR750S – May, 2018

Certain public material may refer to this unit as GL-AR750S-Ext and/or GL.iNet Slate

GL.iNet AR750S

FIXME Any text with a light background (like this one) provides instructions for creating the Details Page. When you have filled in correct/useful information (instead of any template that's there) remove the instructions, as well as the <WRAP> that encloses it.

Supported Versions

Experimental Versions

None at this time.

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
GL-AR750SQualcomm Atheros QCA956377516, 128NAND, microSDXC128Qualcomm Atheros QCA9563, Qualcomm Atheros QCA9887b/g/na/n/ac-3-1x 2.0

Installation

Flash Layout

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(art)ro,-(firmware)

OEM easy installation

FIXME The instructions below are for Broadcom devices and only serve as an example.
Remove / modify them if they do not apply to this particular device!

This section deals with

  • How you install OpenWrt from a device freshly opened
  • The steps required such as reset to factory defaults if the device has already been configured

Note: Reset router to factory defaults if it has been previously configured.

OEM installation using the TFTP method

Specific values needed for tftp

FIXME Enter values for “FILL-IN” below

Bootloader tftp server IPv4 address FILL-IN
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “tftp”)
TFTP transfer window FILL-IN seconds
TFTP window start approximately FILL-IN seconds after power on
TFTP client required IP address FILL-IN

Upgrading OpenWrt

generic.sysupgrade

FIXME These are generic instructions. Update with your router's specifics.

LuCI Web Upgrade Process

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot

Debricking

Failsafe mode

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Network interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

Switch Ports (for VLANs)

From the source code:

ucidef_add_switch “switch0” “0@eth0” “2:lan:2” “3:lan:1” “1:wan”

Source code suggests that the switch is an AR8327 or compatible.

Port Switch port
Internet (WAN) EXAMPLE 1
LAN 1 EXAMPLE 3
LAN 2 EXAMPLE 2

Buttons

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The GL.iNet GL-AR750S has the following buttons:

BUTTON Event
Reset KEY_RESTART
Mode BTN_0

LEDs

The GL.iNet GL-AR750S has the following LEDs:

  • gl-ar750s:green:power
  • gl-ar750s:green:wlan2g
  • gl-ar750s:green:wlan5g

GPIOs (Including I2C and USB-power Control)

The source code contains

#define GL_AR750S_GPIO_LED_WLAN2G 19 #define GL_AR750S_GPIO_LED_WLAN5G 20 #define GL_AR750S_GPIO_LED_POWER 1 #define GL_AR750S_GPIO_USB_POWER 7 #define GL_AR750S_GPIO_BTN_RESET 2 #define GL_AR750S_GPIO_BTN_RIGHT 8 #define GL_AR750S_GPIO_I2C_SDA 5 #define GL_AR750S_GPIO_I2C_SCL 21

Hardware

Info

FIXME

  1. This table is automatically generated, once the correct filters for Brand and Model are set.
  2. If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
  3. If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for GL.iNet GL-AR750S ? If not: Create one.
  4. If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
  5. If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.
Nothing.

Photos

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Opening the case

Note: This will void your warranty!

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, …

  • To remove the cover and open the device, do a/b/c

Main PCB:

Source: https://docs.gl-inet.com/en/3/hardware/ar750s/

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for GL.iNet GL-AR750S @@Version@@
EXAMPLE 115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootloader mods

Hardware mods

None so far.

Bootlogs

OEM bootlog

[ 0.000000] Linux version 4.9.109 (luo@luo-B250M-D3H) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6910-323285a) ) #0 Fri Jun 22 10:22:57 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019750 (MIPS 74Kc) [ 0.000000] SoC: Qualcomm Atheros QCA956X ver 1 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 804ee8a4, node_mem_map 81000020 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=GL-AR750S console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(art)ro,2048k(kernel),13052k(reserved);spi0.1:-(ubi) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 124420K/131072K available (3652K kernel code, 159K rwdata, 856K rodata, 188K init, 217K bss, 6652K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4932285024 ns [ 0.000007] sched_clock: 32 bits at 387MHz, resolution 2ns, wraps every 5541893118ns [ 0.008223] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.071034] pid_max: default: 32768 minimum: 301 [ 0.075985] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.082965] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.092580] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.102987] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.110412] NET: Registered protocol family 16 [ 0.116388] MIPS: machine is GL-AR750S [ 0.359904] registering PCI controller with io_map_base unset [ 0.378266] i2c-gpio i2c-gpio.0: using pins 5 (SDA) and 21 (SCL) [ 0.384805] PCI host bridge to bus 0000:00 [ 0.389162] pci_bus 0000:00: root bus resource [mem 0x12000000-0x13ffffff] [ 0.396403] pci_bus 0000:00: root bus resource [io 0x0001] [ 0.402278] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.409424] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.417803] pci 0000:00:00.0: [168c:0050] type 00 class 0x028000 [ 0.417813] pci 0000:00:00.0: invalid calibration data [ 0.423242] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.423290] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.423356] pci 0000:00:00.0: supports D1 [ 0.423364] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.423550] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.423573] pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit] [ 0.431317] pci 0000:00:00.0: BAR 6: assigned [mem 0x12200000-0x1220ffff pref] [ 0.438935] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.446711] clocksource: Switched to clocksource MIPS [ 0.452954] NET: Registered protocol family 2 [ 0.458376] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.465725] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.472468] TCP: Hash tables configured (established 1024 bind 1024) [ 0.479257] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.485422] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.492285] NET: Registered protocol family 1 [ 0.496942] PCI: CLS 0 bytes, default 32 [ 0.499193] Crashlog allocated RAM at address 0x3f00000 [ 0.505494] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.518286] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.524428] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.542387] io scheduler noop registered [ 0.546518] io scheduler deadline registered (default) [ 0.552343] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.561248] console [ttyS0] disabled [ 0.585087] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 0.594184] console [ttyS0] enabled [ 0.601733] bootconsole [early0] disabled [ 0.615040] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.629678] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.634561] 5 cmdlinepart partitions found on MTD device spi0.0 [ 0.640684] Creating 5 MTD partitions on "spi0.0": [ 0.645636] 0x000000000000-0x000000040000 : "u-boot" [ 0.651976] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.658832] 0x000000050000-0x000000060000 : "art" [ 0.664989] 0x000000060000-0x000000260000 : "kernel" [ 0.671470] 0x000000260000-0x000000f1f000 : "reserved" [ 0.678635] spi-nand: Giga SPI NAND was found. [ 0.683237] spi-nand: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 128 [ 0.691460] 1 cmdlinepart partitions found on MTD device spi0.1 [ 0.697610] Creating 1 MTD partitions on "spi0.1": [ 0.702561] 0x000000000000-0x000008000000 : "ubi" [ 1.157059] found bad block 7fe0000 [ 1.161248] libphy: Fixed MDIO Bus: probed [ 1.174475] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0 [ 1.902067] libphy: ag71xx_mdio: probed [ 2.528158] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316] [ 2.539702] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII [ 2.547585] NET: Registered protocol family 10 [ 2.555273] NET: Registered protocol family 17 [ 2.559972] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.573453] 8021q: 802.1Q VLAN Support v1.8 [ 2.582821] UBI: auto-attach mtd5 [ 2.586268] ubi0: attaching mtd5 [ 2.596725] random: fast init done [ 7.261801] ubi0: scanning is finished [ 7.316973] ubi0: attached mtd5 (name "ubi", size 128 MiB) [ 7.322642] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.329769] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.336787] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.343974] ubi0: good PEBs: 1023, bad PEBs: 1, corrupted PEBs: 0 [ 7.350271] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 7.357736] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 344389367 [ 7.367080] ubi0: available PEBs: 0, total reserved PEBs: 1023, PEBs reserved for bad PEB handling: 19 [ 7.376766] ubi0: background thread "ubi_bgt0d" started, PID 320 [ 7.386358] block ubiblock0_0: created from ubi0:0(rootfs) [ 7.392072] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 7.399269] hctosys: unable to open rtc device (rtc0) [ 7.425429] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 7.433859] Freeing unused kernel memory: 188K [ 7.438472] This architecture does not have kernel memory protection. [ 8.326000] init: Console is alive [ 8.329799] init: - watchdog - [ 11.260090] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 11.425423] usbcore: registered new interface driver usbfs [ 11.431213] usbcore: registered new interface driver hub [ 11.436799] usbcore: registered new device driver usb [ 11.447146] exFAT: Version 1.2.9 [ 11.479946] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.495003] SCSI subsystem initialized [ 11.503105] ehci-platform: EHCI generic platform driver [ 11.508636] ehci-platform ehci-platform.0: EHCI Host Controller [ 11.514777] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 11.525218] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000 [ 11.556747] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 11.564110] hub 1-0:1.0: USB hub found [ 11.568285] hub 1-0:1.0: 1 port detected [ 11.572639] ehci-platform ehci-platform.1: EHCI Host Controller [ 11.578822] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2 [ 11.589296] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000 [ 11.616732] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00 [ 11.624061] hub 2-0:1.0: USB hub found [ 11.628276] hub 2-0:1.0: 1 port detected [ 11.634906] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 11.642663] ohci-platform: OHCI generic platform driver [ 11.650261] uhci_hcd: USB Universal Host Controller Interface driver [ 11.660609] usbcore: registered new interface driver usb-storage [ 11.667461] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 11.677583] init: - preinit - [ 12.278504] usb 2-1: new high-speed USB device number 2 using ehci-platform [ 12.589684] hub 2-1:1.0: USB hub found [ 12.609154] hub 2-1:1.0: 4 ports detected [ 12.944778] random: procd: uninitialized urandom read (4 bytes read) [ 13.048115] usb 2-1.1: new high-speed USB device number 3 using ehci-platform [ 13.284883] usb-storage 2-1.1:1.0: USB Mass Storage device detected [ 13.298655] scsi host0: usb-storage 2-1.1:1.0 [ 13.359763] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.358436] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0233 PQ: 0 ANSI: 0 [ 14.371616] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 14.438390] eth0: link up (1000Mbps/Full duplex) [ 14.443375] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 16.626753] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 442 [ 16.919678] UBIFS (ubi0:1): recovery needed [ 17.508987] UBIFS (ubi0:1): recovery completed [ 17.513654] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 17.521765] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 17.532017] UBIFS (ubi0:1): FS size: 116183040 bytes (110 MiB, 915 LEBs), journal size 5840896 bytes (5 MiB, 46 LEBs) [ 17.542972] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 17.549811] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID F57E0CA7-1F84-4DC7-99DE-8DD2B3010ED3, small LPT model [ 17.600944] mount_root: switching to ubifs overlay [ 17.692169] urandom-seed: Seeding with /etc/urandom.seed [ 17.877918] eth0: link down [ 17.891069] procd: - early - [ 17.894124] procd: - watchdog - [ 18.490893] random: jshn: uninitialized urandom read (4 bytes read) [ 18.557657] procd: - watchdog - [ 18.561120] procd: - ubus - [ 18.750964] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.789173] random: ubusd: uninitialized urandom read (4 bytes read) [ 18.809034] procd: - init - [ 20.811590] kmodloader: loading kernel modules from /etc/modules.d/* [ 20.883550] ntfs: driver 2.1.32 [Flags: R/O MODULE]. [ 20.914512] tun: Universal TUN/TAP device driver, 1.6 [ 20.919779] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 20.953528] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.988207] Netfilter messages via NETLINK v0.30. [ 20.998875] ip_set: protocol 6 [ 21.064831] fuse init (API version 7.26) [ 21.092660] usbcore: registered new interface driver cdc_acm [ 21.098560] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 21.128191] usbcore: registered new interface driver cdc_wdm [ 21.137963] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180 [ 21.146233] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d [ 21.180331] ip_tables: (C) 2000-2006 Netfilter Core Team [ 21.195170] usbcore: registered new interface driver ipheth [ 21.226682] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 21.510763] usbcore: registered new interface driver usbserial [ 21.516925] usbcore: registered new interface driver usbserial_generic [ 21.523750] usbserial: USB Serial support registered for generic [ 21.569433] wireguard: WireGuard 0.0.20180620 loaded. See www.wireguard.com for information. [ 21.578196] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 21.677737] xt_time: kernel timezone is -0000 [ 21.688938] usbcore: registered new interface driver cdc_ether [ 21.704642] usbcore: registered new interface driver cdc_ncm [ 21.888207] usbcore: registered new interface driver cp210x [ 21.894043] usbserial: USB Serial support registered for cp210x [ 21.918037] usbcore: registered new interface driver huawei_cdc_ncm [ 22.023295] PPP generic driver version 2.4.2 [ 22.047052] PPP MPPE Compression module registered [ 22.053704] NET: Registered protocol family 24 [ 22.069249] usbcore: registered new interface driver qmi_wwan [ 22.099467] usbcore: registered new interface driver rndis_host [ 22.137305] usbcore: registered new interface driver sierra [ 22.143143] usbserial: USB Serial support registered for Sierra USB modem [ 22.171849] usbcore: registered new interface driver sierra_net [ 22.250581] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 22.258738] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0 [ 22.577835] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2 [ 22.588917] ath10k_pci 0000:00:00.0: Falling back to user helper [ 30.821829] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 30.848648] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/firmware-6.bin failed with error -2 [ 30.859748] ath10k_pci 0000:00:00.0: Falling back to user helper [ 32.578665] firmware ath10k!QCA9887!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 32.946104] ath10k_pci 0000:00:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000 [ 32.955666] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1 [ 32.968468] ath10k_pci 0000:00:00.0: firmware ver 10.2.4-1.0-00033 api 5 features no-p2p,ignore-otp,skip-clock-init,mfp,allows-mesh-bcast crc32 c232a0c3 [ 33.145742] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9887/hw1.0/board-2.bin failed with error -2 [ 33.156568] ath10k_pci 0000:00:00.0: Falling back to user helper [ 33.328829] firmware ath10k!QCA9887!hw1.0!board-2.bin: firmware_loading_store: map pages failed [ 33.348629] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 546cca0d [ 34.640531] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 34.778124] ath: EEPROM regdomain: 0x0 [ 34.778131] ath: EEPROM indicates default country code should be used [ 34.778134] ath: doing EEPROM country->regdmn map search [ 34.778145] ath: country maps to regdmn code: 0x3a [ 34.778149] ath: Country alpha2 being used: US [ 34.778152] ath: Regpair used: 0x3a [ 34.855572] usbcore: registered new interface driver option [ 34.861468] usbserial: USB Serial support registered for GSM modem (1-port) [ 34.924510] usbcore: registered new interface driver rt2800usb [ 34.949626] ath: EEPROM regdomain: 0x0 [ 34.949634] ath: EEPROM indicates default country code should be used [ 34.949637] ath: doing EEPROM country->regdmn map search [ 34.949649] ath: country maps to regdmn code: 0x3a [ 34.949653] ath: Country alpha2 being used: US [ 34.949656] ath: Regpair used: 0x3a [ 34.959635] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 34.963251] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47 [ 35.036143] kmodloader: done loading kernel modules from /etc/modules.d/* [ 44.563119] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 44.581018] br-lan: port 1(eth0.1) entered blocking state [ 44.586601] br-lan: port 1(eth0.1) entered disabled state [ 44.592546] device eth0.1 entered promiscuous mode [ 44.597538] device eth0 entered promiscuous mode [ 44.633895] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 44.695412] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 46.350304] eth0: link up (1000Mbps/Full duplex) [ 46.721345] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 46.777314] br-lan: port 1(eth0.1) entered blocking state [ 46.782895] br-lan: port 1(eth0.1) entered forwarding state [ 46.788821] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 46.976794] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 50.927246] fast-classifier: starting up [ 50.931461] fast-classifier: registered [ 53.231377] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 53.253305] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 53.299678] br-lan: port 2(wlan0) entered blocking state [ 53.305173] br-lan: port 2(wlan0) entered disabled state [ 53.311063] device wlan0 entered promiscuous mode [ 53.316096] br-lan: port 2(wlan0) entered blocking state [ 53.321629] br-lan: port 2(wlan0) entered forwarding state [ 53.421836] br-lan: port 3(wlan1) entered blocking state [ 53.427386] br-lan: port 3(wlan1) entered disabled state [ 53.433298] device wlan1 entered promiscuous mode [ 53.438456] br-lan: port 3(wlan1) entered blocking state [ 53.443945] br-lan: port 3(wlan1) entered forwarding state [ 53.908427] br-lan: port 2(wlan0) entered disabled state [ 53.914061] br-lan: port 3(wlan1) entered disabled state [ 55.336019] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 55.342782] br-lan: port 3(wlan1) entered blocking state [ 55.348294] br-lan: port 3(wlan1) entered forwarding state [ 55.546496] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 55.553295] br-lan: port 2(wlan0) entered blocking state [ 55.558826] br-lan: port 2(wlan0) entered forwarding state [ 78.291939] random: crng init done [ 78.295462] random: 6 urandom warning(s) missed due to ratelimiting


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Space for additional notes, links to forum threads or other resources.

Tags

FIXME Add tags below, then remove this fixme.

How to add tags

toh/gl-inet/gl-ar750s.txt · Last modified: 2018/09/03 07:10 by yuvadm