D-Link EAGLE PRO AI R32 A1

Overview:

MediaTek MT7622BV dual core CPU using 2.4GHz and 5GHz WiFi (both AX)
MediaTek MT7531BE switch
Mediatek MT7975AN + MT7915AN for 5GHz
512MB RAM
128MB NAND flash
1 1Gbit WAN port
4 1Gbit LAN ports
2 LEDs (Status and Internet, both can be either orange or white)
2 buttons (WPS and Reset)

The R32 is like the D-Link M32, with the following differences: * 4 LAN ports instead of 2 * The recory image starts with DLK6E6015001 instaed of DLK6E6010001 * Individual LEDs for power and internet * MAC address is stored at another offset in the ODM partition

MAC addresses: * WAN MAC is stored in partition “Odm” at offset 0x81 * LAN (as printed on the device) is WAN MAC + 1 * WLAN MAC (2.4 GHz) is WAN MAC + 2 * WLAN MAC (5GHz) is WAN MAC + 3

/

None at this time.

Set your IP address to 192.168.0.10, subnet mask 255.255.255.0
Press the reset button while powering on the device
Keep the reset button pressed until the internet LED blinks fast
Open a Web browser and go to http://192.168.0.1
Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin

Open the case, connect to the UART console
Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
Power on the device and select “1. System Load Linux to SDRAM via TFTP.” in the boot menu
Enter image file, tftp server IP and device IP (if they differ from the default).
TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
Reboot the device. OpenWrt should start from flash now

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

root@OpenWrt:~# df -h
Filesystem                Size      Used Available Use% Mounted on
/dev/root                 4.5M      4.5M         0 100% /rom
tmpfs                   244.2M    228.0K    244.0M   0% /tmp
/dev/ubi0_1              64.6M    160.0K     61.1M   0% /overlay
overlayfs:/overlay       64.6M    160.0K     61.1M   0% /
tmpfs                   512.0K         0    512.0K   0% /dev

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00080000 00020000 "Preloader"
mtd1: 00040000 00020000 "ATF"
mtd2: 00080000 00020000 "Bootloader"
mtd3: 00040000 00020000 "BootConfig"
mtd4: 00040000 00020000 "Odm"
mtd5: 00080000 00020000 "Config1"
mtd6: 00080000 00020000 "Config2"
mtd7: 05a00000 00020000 "Kernel1"
mtd8: 00420000 00020000 "kernel"
mtd9: 05200000 00020000 "ubi"
mtd10: 00100000 00020000 "Factory"
mtd11: 00200000 00020000 "Mydlink"
mtd12: 00300000 00020000 "Storage"

See “Flashing via Recovery Web Interface” above

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

Please fill in real values for this device, then remove the EXAMPLEs

The D-Link EAGLE PRO AI R32 has the following buttons:

BUTTON	Event
EXAMPLE Reset	reset
EXAMPLE Secure Easy Setup	ses
EXAMPLE No buttons at all.	-

This table is automatically generated, once the correct filters for Brand and Model are set.
If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for D-Link EAGLE PRO AI R32 A1? If not: Create one.
If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.

---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=D-Link filter : Model=EAGLE PRO AI R32 filter : Versions=A1

Front:

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

To remove the cover and open the device, do a/b/c

Main PCB:
Insert photo of PCB

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Replace EXAMPLE by real values.

Serial connection parameters for D-Link EAGLE PRO AI R32 A1	EXAMPLE 115200, 8N1, 3.3V

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

F0: 102B 0000 F6: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 0000 0041 [0000] G0: 0190 0000 T0: 0000 0369 [000F] Jump to BL UNIVPLL_CON0 = 0xFE000000!!! mt_pll_init: Set pll frequency for 25M crystal [PMIC_WRAP]wrap_init pass,the return value=0. [pmic_init] Preloader Start.................. [pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3 [pmic_init] Done................... Chip part number:7622B MT7622 Version: 1.2.8, (iPA) SSC OFF mt_pll_post_init: mt_get_cpu_freq = 1350000Khz mt_pll_post_init: mt_get_mem_freq = 1600000Khz mt_pll_post_init: mt_get_bus_freq = 1119920Khz [PLFM] Init I2C: OK(0) [BLDR] Build Time: 20200518-110732 ==== Dump RGU Reg ======== RGU MODE: 4D RGU LENGTH: FFE0 RGU STA: 0 RGU INTERVAL: FFF RGU SWSYSRST: 8000 ==== Dump RGU Reg End ==== RGU: g_rgu_satus:0 mtk_wdt_mode_config mode value=10, tmp:22000010 PL P ON WDT does not trigger reboot WDT NONRST=0x20000000 WDT IRQ_EN=0x340003 RGU mtk_wdt_init:MTK_WDT_DEBUG_CTL(590200F3) [EMI] MDL number = 2 [EMI] DRAMC calibration start [EMI] DRAMC calibration end [EMI]rank size auto detect [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x48000000]= 0xEDCBA987 [EMI]start_addr[0x40000000]=0x12345678, test_addr[0x50000000]= 0xEDCBA987 [EMI]start_addr[0x40000000]=0xEDCBA987, test_addr[0x60000000]= 0xEDCBA987 [EMI]rank0 size: 0x20000000 [MEM] complex R/W mem test pass RAM_CONSOLE wdt status (0x0)=0x0 [BBT] BMT.v2 is found at 0x3FF [PLFM] Init Boot Device: OK(0) [PART] blksz: 2048B [PART] [0x0000000000000000-0x000000000007FFFF] "PRELOADER" (256 blocks) [PART] [0x0000000000080000-0x00000000000BFFFF] "tee1" (128 blocks) [PART] [0x00000000000C0000-0x000000000013FFFF] "lk" (256 blocks) Device APC domain init setup: Domain Setup (0x0) Domain Setup (0x0) Device APC domain after setup: Domain Setup (0x0) Domain Setup (0x0) Bad_Block_Table init, sizeof(Bad_Block_Table)= 8192 [PART] Image with part header [PART] name : LK [PART] addr : FFFFFFFFh mode : -1 [PART] size : 436452 [PART] magic: 58881688h [PART] load "lk" from 0x00000000000C0200 (dev) to 0x41E00000 (mem) [SUCCESS] [PART] load speed: 10147KB/s, 436452 bytes, 42ms load lk (ret=0) [PART] Image with part header [PART] name : atf [PART] addr : FFFFFFFFh mode : -1 [PART] size : 57936 [PART] magic: 58881688h [PART] load "tee1" from 0x0000000000080200 (dev) to 0x43000DC0 (mem) [SUCCESS] [PART] load speed: 9429KB/s, 57936 bytes, 6ms load tee1 (ret=0) [BLDR] bldr load tee part ret=0x0, addr=0x43001000 [BLDR] boot part. not found [BLDR] part_load_images ret=0x0 [BLDR] Others, jump to ATF [BLDR] jump to 0x41E00000 [BLDR] <0x41E00000>=0xEA00000F [BLDR] <0x41E00004>=0xE59FF014 U-Boot 2014.04-rc1-gbf1a898-dirty (Aug 13 2021 - 06:46:59) auto detection g_total_rank_size = 0x1F000000 DRAM: 496 MiB NAND: Recognize SNAND: ID [c2 12 ], Device Name [MX35LF1GE4AB], Page Size [2048]B Spare Size [64]B Total Size [128]MB [mtk_snand] probe successfully! [BBT] BMT.v2 is found at 0x3ff 128 MiB In: serial Out: serial Err: serial Net: mtk_eth Uip activated ### main_loop entered: bootdelay=3 *** U-Boot SPI NAND *** 1. System Load Linux to SDRAM via TFTP. 2. System Load Linux Kernel then write to Flash via TFTP. 3. Boot system code via Flash. 4. System Load U-Boot then write to Flash via TFTP. 5. System Load U-Boot then write to Flash via Serial. 6. System Load ATF then write to Flash via TFTP. 7. System Load Preloader then write to Flash via TFTP. 8. System Load ROM header then write to Flash via TFTP. 9. System Load CTP then write to Flash via TFTP. a. System Load CTP then Boot to CTP (via Flash). b. HTTP server. U-Boot console Press UP/DOWN to move or Press 1~9,a~b to choose, ENTER to select ETH already turn on and power on flow will be skipped... Waiting for RX_DMA_BUSY status Start... done mt7531: mt7531_sw_init mt7531: mt7531_core_pll_setup, hwstrap = 000000ff, xtal=25MHz mt7531: mt7531_mac_port_setup, port = 6 mt7531: mt7531_set_port_sgmii_force_mode, port = 6 mt7531: timeout waiting for SGMII_LINK mt7531: mt7531_mac_port_setup, PMCR6 = f805633b >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: CALDLY = 40 0x1e-e0 = 2929 0x1f-115 = 5 GE Rext AnaCal Done! (9)(0x29) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (10) (0x32)(0xb2) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE 1e_174(0xb1b1), 1e_175(0xb2b1) GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2201 GE Tx offset AnaCal Done! (pair-2)(4)(0x4) 0x1e_173=0x420 GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x403 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x701c) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1818) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1a22) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1c24) PORT 0 RX_DC_OFFSET before pairA output = f after pairA output = 1 before pairB output = e after pairB output = ff before pairC output = 1e after pairC output = 1 before pairD output = 1d after pairD output = 1 -------- gephy-calibration (port:0)(0) -------- CALDLY = 40 GE R50 AnaCal Done! (13) (0x26)(0xa6) GE R50 AnaCal Done! (12) (0x30)(0xb0) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (12) (0x30)(0xb0) GE 1e_174(0xa6b0), 1e_175(0xb1b0) GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420 GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2421 GE Tx offset AnaCal Done! (pair-2)(2)(0x21) 0x1e_173=0x2120 GE Tx offset AnaCal Done! (pair-3)(4)(0x4) 0x1e_173=0x2104 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1d1d) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1820) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1820) PORT 1 RX_DC_OFFSET before pairA output = f after pairA output = ff before pairB output = d after pairB output = ff before pairC output = e after pairC output = 0 before pairD output = 1d after pairD output = fe -------- gephy-calibration (port:1)(0) -------- CALDLY = 40 GE R50 AnaCal Done! (12) (0x30)(0xb0) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (11) (0x31)(0xb1) GE R50 AnaCal Done! (10) (0x32)(0xb2) GE 1e_174(0xb0b1), 1e_175(0xb1b2) GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 GE Tx offset AnaCal Done! (pair-1)(2)(0x2) 0x1e_172=0x2202 GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320 GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x2303 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1a22) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1a22) PORT 2 RX_DC_OFFSET before pairA output = f after pairA output = 0 before pairB output = 1d after pairB output = 0 before pairC output = 1d after pairC output = 1 before pairD output = e after pairD output = 0 -------- gephy-calibration (port:2)(0) -------- CALDLY = 40 GE R50 AnaCal Done! (13) (0x26)(0xa6) GE R50 AnaCal Done! (12) (0x30)(0xb0) GE R50 AnaCal Done! (13) (0x26)(0xa6) GE R50 AnaCal Done! (14) (0x24)(0xa4) GE 1e_174(0xa6b0), 1e_175(0xa6a4) GE Tx offset AnaCal Done! (pair-0)(1)(0x1) 0x1e_172=0x120 GE Tx offset AnaCal Done! (pair-1)(4)(0x23) 0x1e_172=0x123 GE Tx offset AnaCal Done! (pair-2)(3)(0x22) 0x1e_173=0x2220 GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x2203 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1f1f) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1f27) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1b23) PORT 3 RX_DC_OFFSET before pairA output = 1d after pairA output = 0 before pairB output = 1e after pairB output = ff before pairC output = e after pairC output = 0 before pairD output = e after pairD output = ff -------- gephy-calibration (port:3)(0) -------- CALDLY = 40 GE R50 AnaCal Done! (9) (0x34)(0xb4) GE R50 AnaCal Done! (9) (0x34)(0xb4) GE R50 AnaCal Done! (8) (0x35)(0xb5) GE R50 AnaCal Done! (9) (0x34)(0xb4) GE 1e_174(0xb4b4), 1e_175(0xb5b4) GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2201 GE Tx offset AnaCal Done! (pair-2)(1)(0x1) 0x1e_173=0x120 GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x102 GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5816) GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1616) GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1018) GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1018) PORT 4 RX_DC_OFFSET before pairA output = 1e after pairA output = ff before pairB output = e after pairB output = 1 before pairC output = 1e after pairC output = ff before pairD output = e after pairD output = ff -------- gephy-calibration (port:4)(0) -------- 0x1b000014 = 0x00110214 start load_p_section load_section: start p mode load_section: found csxf tag csxf->magic: 5343 csxf->checksum: 8051 csxf->body_length: 000014ad csxf->body_encoding: 00 csxf->raw_length: 000014ad check p section: ok load P section success @180000 romid: (DLK6E6010001) sys info PV 01 model name: (M32) ecn no: (200909100001) beid rule: 190A beid mac: << WAN_MAC >> default ip: 192:168:0:1 aup_start Using mtk_eth device mcast upgrade timeout. NAND read: device 0 offset 0x2c0000, size 0x2000 8192 bytes read: OK [do_read_image_blks]This is a FIT image,img_size = 0x2d942c [do_read_image_blks]img_blks = 0x5b3 [do_read_image_blks]img_align_size = 0x2d9800 NAND read: device 0 offset 0x2c0000, size 0x2d9800 [mtk_snand_check_bch_error] ECC-C, #err:1, PA=1589, S=2 NFI Less than 2 bit error, ignore 2988032 bytes read: OK bootm flag=0, states=70f ## Loading kernel from FIT Image at 4007ff28 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM64 mt7622-covr326x Linux-4.4.124 Type: Kernel Image Compression: lzma compressed Data Start: 0x40080018 Data Size: 2956940 Bytes = 2.8 MiB Architecture: AArch64 OS: Linux Load Address: 0x41080000 Entry Point: 0x41080000 Hash algo: crc32 Hash value: 5892889d Hash algo: sha1 Hash value: ffb2cfbbdff58e4ed1f6aea6c007af6c5000710f Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 4007ff28 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Description: ARM64 mt7622-covr326x device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x40351fdc Data Size: 28749 Bytes = 28.1 KiB Architecture: AArch64 Hash algo: crc32 Hash value: bc180f0b Hash algo: sha1 Hash value: 6983b73f0bfa717b27f7105c4a2effce77a98cc9 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x40351fdc Uncompressing Kernel Image ... OK Loading Device Tree to 5cd9c000, end 5cda604c ... OK bootargs:(console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs boot_part=Kernel1) Starting kernel ... [ATF][ 13.425391]save kernel info [ATF][ 13.428422]Kernel_EL2 [ATF][ 13.431178]Kernel is 64Bit [ATF][ 13.434366]pc=0x41080000, r0=0x5cd9c000, r1=0x0 INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel INFO: BL3-1: Next image address = 0x41080000 INFO: BL3-1: Next image spsr = 0x3c9 [ATF][ 13.452635]el3_exit [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.124 (oe-user@oe-host) (gcc version 7.3.0 (GCC) ) #1 SMP PREEMPT Thu Apr 21 10:33:53 UTC 2022 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] On node 0 totalpages: 131024 [ 0.000000] DMA zone: 2048 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 131024 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv0.2 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] PERCPU: Embedded 19 pages/cpu @ffffffc01ffa6000 s39320 r8192 d30312 u77824 [ 0.000000] pcpu-alloc: s39320 r8192 d30312 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 128976 [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 swiotlb=512 rootfstype=squashfs boot_part=Kernel1 [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] software IO TLB [mem 0x5fcf4000-0x5fdf4000] (1MB) mapped at [ffffffc01fcf4000-ffffffc01fdf3fff] [ 0.000000] Memory: 496880K/524096K available (5620K kernel code, 446K rwdata, 1712K rodata, 360K init, 406K bss, 27216K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] .init : 0xffffff80087ad000 - 0xffffff8008807000 ( 360 KB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff80085fe000 ( 5624 KB) [ 0.000000] .rodata : 0xffffff80085fe000 - 0xffffff80087ad000 ( 1724 KB) [ 0.000000] .data : 0xffffff8008807000 - 0xffffff8008876b38 ( 447 KB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc0800000 ( 8 MB actual) [ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc020000000 ( 512 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 12.50MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns [ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns [ 0.000058] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 191126102035 ns [ 0.000224] Console: colour dummy device 80x25 [ 0.000239] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000) [ 0.000247] pid_max: default: 32768 minimum: 301 [ 0.000295] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000301] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000766] sched-energy: CPU device node has no sched-energy-costs [ 0.000773] Invalid sched_group_energy for CPU0 [ 0.000776] CPU0: update cpu_capacity 1024 [ 0.000805] ASID allocator initialised with 32768 entries [ 0.032100] Detected VIPT I-cache on CPU1 [ 0.032129] Invalid sched_group_energy for CPU1 [ 0.032131] CPU1: update cpu_capacity 1024 [ 0.032133] CPU1: Booted secondary processor [410fd034] [ 0.032167] Brought up 2 CPUs [ 0.032179] SMP: Total of 2 processors activated. [ 0.032186] CPU: All CPU(s) started at EL2 [ 0.032199] alternatives: patching kernel code [ 0.032292] Invalid sched_group_energy for CPU1 [ 0.032298] Invalid sched_group_energy for Cluster1 [ 0.032301] Invalid sched_group_energy for CPU0 [ 0.032304] Invalid sched_group_energy for Cluster0 [ 0.032548] devtmpfs: initialized [ 0.036756] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.036774] futex hash table entries: 512 (order: 4, 65536 bytes) [ 0.036886] pinctrl core: initialized pinctrl subsystem [ 0.037403] NET: Registered protocol family 16 [ 0.037840] [SPM] spm_base = ffffff8008026000 [ 0.037845] [SPM] spm_irq_0 = 6, spm_irq_1 = 7 [ 0.037848] [SPM] spm_irq_2 = 8, spm_irq_3 = 9 [ 0.037851] [SPM] set spm as wakeup devcie. [ 0.037856] [SPM] spm_rtc cnt: 24414. [ 0.052080] cpuidle: using governor menu [ 0.052141] vdso: 2 pages (1 code @ ffffff8008603000, 1 data @ ffffff800880c000) [ 0.052297] DMA: preallocated 256 KiB pool for atomic allocations [ 0.052380] Serial: AMBA PL011 UART driver [ 0.052432] [SPM] PWAKE_EN:1, PCMWDT_EN:0, BYPASS_SYSPWREQ:0, I2C_CHANNEL:2 [ 0.052437] [SLP] SLEEP_DPIDLE_EN:1, REPLACE_DEF_WAKESRC:0, SUSPEND_LOG_EN:1 [ 0.081152] vgaarb: loaded [ 0.081355] SCSI subsystem initialized [ 0.081560] usbcore: registered new interface driver usbfs [ 0.081597] usbcore: registered new interface driver hub [ 0.081636] usbcore: registered new device driver usb [ 0.083027] rbus 18000000.wbsys: PCI host bridge to bus 0000:00 [ 0.083043] pci_bus 0000:00: root bus resource [mem 0x18000000-0x180fffff] [ 0.083050] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.083069] pci 0000:00:00.0: [14c3:7622] type 00 class 0x000280 [ 0.083085] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit] [ 0.083091] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f] [ 0.083098] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f] [ 0.083104] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f] [ 0.083111] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f] [ 0.083143] pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22 [ 0.083446] clocksource: Switched to clocksource arch_sys_counter [ 0.089302] NET: Registered protocol family 2 [ 0.089668] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.089699] TCP bind hash table entries: 4096 (order: 4, 65536 bytes) [ 0.089756] TCP: Hash tables configured (established 4096 bind 4096) [ 0.089802] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.089815] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.089920] NET: Registered protocol family 1 [ 0.089958] PCI: CLS 0 bytes, default 128 [ 0.097250] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.097433] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.097869] fuse init (API version 7.23) [ 0.101411] NET: Registered protocol family 38 [ 0.101452] io scheduler noop registered [ 0.101690] io scheduler cfq registered (default) [ 0.119677] mtk-pcie 1a140000.pcie: pcie rc 0 linkup success [ 0.219703] mtk-pcie 1a140000.pcie: Port1 link down [ 0.219858] mtk-pcie 1a140000.pcie: PCI host bridge to bus 0001:00 [ 0.219867] pci_bus 0001:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.219874] pci_bus 0001:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.219881] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.219916] pci 0001:00:00.0: [14c3:5396] type 01 class 0x060400 [ 0.219968] pci 0001:00:00.0: reg 0x10: [mem 0x00000000-0xffffffff 64bit pref] [ 0.220088] pci 0001:00:00.0: of_irq_parse_pci() failed with rc=-22 [ 0.220211] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.220432] pci 0001:01:00.0: [14c3:7915] type 00 class 0x000280 [ 0.220737] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 0.220850] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 0.220963] pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 0.221476] pci 0001:01:00.0: supports D1 D2 [ 0.221483] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.227513] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.227551] pci 0001:00:00.0: BAR 0: no space for [mem size 0x100000000 64bit pref] [ 0.227558] pci 0001:00:00.0: BAR 0: failed to assign [mem size 0x100000000 64bit pref] [ 0.227564] pci 0001:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 0.227574] pci 0001:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 0.227665] pci 0001:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] [ 0.227756] pci 0001:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] [ 0.227845] pci 0001:00:00.0: PCI bridge to [bus 01] [ 0.227857] pci 0001:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 0.227915] pcieport 0001:00:00.0: of_irq_parse_pci() failed with rc=-22 [ 0.227930] pcieport 0001:00:00.0: enabling device (0000 -> 0002) [ 0.228091] pcieport 0001:00:00.0: Signaling PME through PCIe PME interrupt [ 0.228097] pci 0001:01:00.0: Signaling PME through PCIe PME interrupt [ 0.228106] pcie_pme 0001:00:00.0:pcie01: service driver pcie_pme loaded [ 0.232760] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.233905] console [ttyS0] disabled [ 0.254068] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 230, base_baud = 1562500) is a ST16650V2 [ 1.117809] console [ttyS0] enabled [ 1.141905] 11005000.serial: ttyS1 at MMIO 0x11005000 (irq = 231, base_baud = 1562500) is a ST16650V2 [ 1.151861] Unable to detect cache hierarchy for CPU 0 [ 1.160121] loop: module loaded [ 1.163749] dump_power_table[0] = { .cpufreq_khz = 1350000, .cpufreq_ncpu = 2, .cpufreq_power = 995 } [ 1.173091] dump_power_table[1] = { .cpufreq_khz = 1262500, .cpufreq_ncpu = 2, .cpufreq_power = 811 } [ 1.182309] dump_power_table[2] = { .cpufreq_khz = 1137500, .cpufreq_ncpu = 2, .cpufreq_power = 736 } [ 1.191527] dump_power_table[3] = { .cpufreq_khz = 1025000, .cpufreq_ncpu = 2, .cpufreq_power = 624 } [ 1.200748] dump_power_table[4] = { .cpufreq_khz = 1350000, .cpufreq_ncpu = 1, .cpufreq_power = 517 } [ 1.209966] dump_power_table[5] = { .cpufreq_khz = 812500, .cpufreq_ncpu = 2, .cpufreq_power = 492 } [ 1.219095] dump_power_table[6] = { .cpufreq_khz = 1262500, .cpufreq_ncpu = 1, .cpufreq_power = 377 } [ 1.228316] dump_power_table[7] = { .cpufreq_khz = 600000, .cpufreq_ncpu = 2, .cpufreq_power = 376 } [ 1.237444] dump_power_table[8] = { .cpufreq_khz = 1137500, .cpufreq_ncpu = 1, .cpufreq_power = 333 } [ 1.246658] dump_power_table[9] = { .cpufreq_khz = 437500, .cpufreq_ncpu = 2, .cpufreq_power = 295 } [ 1.255785] dump_power_table[10] = { .cpufreq_khz = 1025000, .cpufreq_ncpu = 1, .cpufreq_power = 258 } [ 1.265085] dump_power_table[11] = { .cpufreq_khz = 300000, .cpufreq_ncpu = 2, .cpufreq_power = 225 } [ 1.274299] dump_power_table[12] = { .cpufreq_khz = 812500, .cpufreq_ncpu = 1, .cpufreq_power = 204 } [ 1.283513] dump_power_table[13] = { .cpufreq_khz = 600000, .cpufreq_ncpu = 1, .cpufreq_power = 166 } [ 1.292727] dump_power_table[14] = { .cpufreq_khz = 437500, .cpufreq_ncpu = 1, .cpufreq_power = 140 } [ 1.301940] dump_power_table[15] = { .cpufreq_khz = 300000, .cpufreq_ncpu = 1, .cpufreq_power = 119 } [ 1.312291] [cal] calefuse1 = 0x7da7ab80 [ 1.316220] [cal] calefuse2 = 0x458010 [ 1.319970] [cal] g_adc_ge_t = 0x27a [ 1.323541] [cal] g_adc_oe_t = 0x1f6 [ 1.327106] [cal] g_degc_cali = 0x2e [ 1.330679] [cal] g_adc_cali_en_t = 0x1 [ 1.334511] [cal] g_o_slope = 0x0 [ 1.337825] [cal] g_o_slope_sign = 0x0 [ 1.341569] [cal] g_id = 0x0 [ 1.344535] [cal] g_o_vtsmcu1 = 0x0 [ 1.348019] [cal] g_o_vtsmcu2 = 0x116 [ 1.351679] [cal] g_o_vtsmcu3 = 0x0 [ 1.355156] [cal] g_o_vtsmcu4 = 0x0 [ 1.358643] [cal] g_ge = 0x129 [ 1.361780] [cal] g_gain = 0x2839 [ 1.365177] [cal] g_x_roomt1 = 0x1f6c [ 1.372351] mtk-snand 1100d000.snfi: mtk_snand_init_hw [ 1.377503] mtk-snand 1100d000.snfi: # MTK SNAND # : Use HW ECC [ 1.393535] Recognize NAND: ID [ [ 1.396586] c2 12 [ 1.398596] ], [MX35LF1GE4AB], Page[2048]B, Spare [64]B Total [128]MB [ 1.405408] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0x12 [ 1.411756] nand: Macronix SNAND 128MiB 3,3V 8-bit [ 1.416547] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.424111] [NAND]select ecc bit:4, sparesize :64 [ 1.430251] [BBT] BMT.v2 is found at 0x3ff [ 1.434377] 12 ofpart partitions found on MTD device MTK-SNAND [ 1.440207] Creating 12 MTD partitions on "MTK-SNAND": [ 1.445345] 0x000000000000-0x000000080000 : "Preloader" [ 1.451526] 0x000000080000-0x0000000c0000 : "ATF" [ 1.456905] 0x0000000c0000-0x000000140000 : "Bootloader" [ 1.463038] 0x000000140000-0x000000180000 : "BootConfig" [ 1.469027] 0x000000180000-0x0000001c0000 : "Odm" [ 1.474404] 0x0000001c0000-0x000000240000 : "Config1" [ 1.480289] 0x000000240000-0x0000002c0000 : "Config2" [ 1.486186] 0x0000002c0000-0x000002fc0000 : "Kernel1" [ 1.519656] 2 fit-fw partitions found on MTD device Kernel1 [ 1.525230] 0x0000002c0000-0x0000005a0000 : "kernel" [ 1.532455] 0x0000005a0000-0x000002fc0000 : "rootfs" [ 1.563616] mtd: device 9 (rootfs) set to be root filesystem [ 1.569280] 1 squashfs-split partitions found on MTD device rootfs [ 1.575461] 0x000002620000-0x000002fc0000 : "rootfs_data" [ 1.587239] 0x000002fc0000-0x000005cc0000 : "Kernel2" [ 1.620244] 0x000005cc0000-0x000005dc0000 : "Factory" [ 1.626428] 0x000005dc0000-0x000005fc0000 : "Mydlink" [ 1.633224] 0x000005fc0000-0x0000062c0000 : "Storage" [ 1.640646] mtk-snand 1100d000.snfi: [mtk_snand] probe successfully! [ 1.648734] libphy: Fixed MDIO Bus: probed [ 1.653202] sean debug physpeed = 2500 [ 1.690698] libphy: mdio: probed [ 1.693951] mtk_soc_eth 1b100000.ethernet: generated random MAC address ba:bd:50:3d:ce:f1 [ 1.702297] mtk_soc_eth 1b100000.ethernet: connected mac 0 to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY] [ 1.712957] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffff8008980000, irq 250 [ 1.722093] netif_napi_add() called with weight 256 on device [ 1.728029] PPP generic driver version 2.4.2 [ 1.732430] PPP BSD Compression module registered [ 1.737142] PPP Deflate Compression module registered [ 1.742211] PPP MPPE Compression module registered [ 1.747004] NET: Registered protocol family 24 [ 1.751465] PPTP driver version 0.8.5 [ 1.755584] 1a0c0000.usb supply vbus not found, using dummy regulator [ 1.762054] 1a0c0000.usb supply vusb33 not found, using dummy regulator [ 1.768948] xhci-mtk 1a0c0000.usb: xHCI Host Controller [ 1.774186] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1 [ 1.781666] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x00210010 [ 1.790046] xhci-mtk 1a0c0000.usb: irq 246, io mem 0x1a0c0000 [ 1.796231] hub 1-0:1.0: USB hub found [ 1.799995] hub 1-0:1.0: 2 ports detected [ 1.804275] xhci-mtk 1a0c0000.usb: xHCI Host Controller [ 1.809503] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2 [ 1.816933] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.825384] hub 2-0:1.0: USB hub found [ 1.829145] hub 2-0:1.0: 1 port detected [ 1.833402] usbcore: registered new interface driver usb-storage [ 1.839650] rtc rtc0: alarm rollover: day [ 1.843661] rtc rtc0: invalid alarm value: 1900-1-2 2022213768:1073741856:0 [ 1.850728] rtc rtc0: test: dev (254:0) [ 1.854571] rtc-test rtc-test.0: rtc core: registered test as rtc0 [ 1.860839] rtc rtc1: alarm rollover: day [ 1.864852] rtc rtc1: invalid alarm value: 1900-1-2 2022213768:1073741856:0 [ 1.871904] rtc rtc1: test: dev (254:1) [ 1.875739] rtc-test rtc-test.1: rtc core: registered test as rtc1 [ 1.881927] i2c /dev entries driver [ 1.886848] MTK_WDT_NONRST_REG(20000000) [ 1.890991] mtk-wdt 10212000.watchdog: register restart_handler on reboot_notifier_list for psci reset [ 1.900302] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.908313] register cpuidle driver!!!!!!!!!!!!!!!!! [ 1.913566] sdhci: Secure Digital Host Controller Interface driver [ 1.919751] sdhci: Copyright(c) Pierre Ossman [ 1.924535] msdc_drv_probe! [ 1.927714] mtk-msdc 11230000.mmc: Regulator set error -22: 3300000 - 3300000 [ 1.973946] mtk-msdc 11230000.mmc: Regulator set error -22: 3300000 - 3300000 [ 2.024019] mtk-msdc 11230000.mmc: Regulator set error -22: 3300000 - 3300000 [ 2.076197] mtk-msdc 11230000.mmc: Regulator set error -22: 3300000 - 3300000 [ 2.699452] mtk_soc_eth 1b100000.ethernet: path gmac1_sgmii in set_mux_gdm1_to_gmac1_esw updated = 1 [ 2.708584] mtk_soc_eth 1b100000.ethernet: mux mux_gmac2_gmac0_to_gephy isn't present on the SoC [ 2.717365] mtk_soc_eth 1b100000.ethernet: mux mux_u3_gmac2_to_qphy isn't present on the SoC [ 2.725803] mtk_soc_eth 1b100000.ethernet: path gmac1_sgmii in set_mux_gmac1_gmac2_to_sgmii_rgmii updated = 1 [ 2.735712] mtk_soc_eth 1b100000.ethernet: mux mux_gmac12_to_gephy_sgmii isn't present on the SoC [ 3.969220] u32 classifier [ 3.971956] Netfilter messages via NETLINK v0.30. [ 3.976702] nf_conntrack version 0.5.0 (3881 buckets, 15524 max) [ 3.982985] ctnetlink v0.93: registering with nfnetlink. [ 3.988435] xt_time: kernel timezone is -0000 [ 3.992802] ip_set: protocol 6 [ 3.995945] ipip: IPv4 over IPv4 tunneling driver [ 4.000983] gre: GRE over IPv4 demultiplexor driver [ 4.005867] ip_gre: GRE over IPv4 tunneling driver [ 4.011349] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.016791] Initializing XFRM netlink socket [ 4.021592] NET: Registered protocol family 10 [ 4.026920] sit: IPv6 over IPv4 tunneling driver [ 4.032284] NET: Registered protocol family 17 [ 4.036758] NET: Registered protocol family 15 [ 4.041234] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 4.053892] Bridge firewalling registered [ 4.057911] Ebtables v2.0 registered [ 4.061618] l2tp_core: L2TP core driver, V2.0 [ 4.065989] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 4.070783] 8021q: 802.1Q VLAN Support v1.8 [ 4.075477] registered taskstats version 1 [ 4.619765] mt753x gsw@0: Switch is MediaTek MT7531BE rev 1 [ 4.629869] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz [ 4.641096] libphy: mt753x_mdio: probed [ 4.899708] random: nonblocking pool is initialized [ 4.932902] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: [ 4.941075] mt753x gsw@0: -------- gephy-calbration (port:0) -------- [ 4.957812] CALDLY = 40 [ 5.030034] 0x1e-e0 = 2929 [ 5.034738] 0x1f-115 = 5 [ 5.037269] GE Rext AnaCal Done! (9)(0x29) [ 5.116831] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 5.191069] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 5.259934] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 5.334138] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 5.342497] GE 1e_174(0xb1b1), 1e_175(0xb2b1) [ 5.390664] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 5.413332] GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2201 [ 5.451858] GE Tx offset AnaCal Done! (pair-2)(4)(0x4) 0x1e_173=0x420 [ 5.485015] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x403 [ 5.590990] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x701c) [ 5.627876] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1818) [ 5.688665] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1b23) [ 5.749444] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1c24) [ 5.803256] PORT 0 RX_DC_OFFSET [ 5.817540] before pairA output = f [ 5.823106] after pairA output = 1 [ 5.828505] before pairB output = e [ 5.834070] after pairB output = 0 [ 5.839468] before pairC output = 1e [ 5.845113] after pairC output = 1 [ 5.850511] before pairD output = 1d [ 5.856163] after pairD output = 1 [ 5.859865] mt753x gsw@0: -------- gephy-calbration (port:1) -------- [ 5.876562] CALDLY = 40 [ 5.959508] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 6.039100] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 6.113317] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 6.192865] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 6.201235] GE 1e_174(0xa6b0), 1e_175(0xb1b0) [ 6.260042] GE Tx offset AnaCal Done! (pair-0)(5)(0x24) 0x1e_172=0x2420 [ 6.288040] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2421 [ 6.310687] GE Tx offset AnaCal Done! (pair-2)(1)(0x1) 0x1e_173=0x120 [ 6.349166] GE Tx offset AnaCal Done! (pair-3)(4)(0x4) 0x1e_173=0x104 [ 6.428641] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) [ 6.492017] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1d1d) [ 6.526293] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1820) [ 6.560548] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1820) [ 6.614276] PORT 1 RX_DC_OFFSET [ 6.628566] before pairA output = f [ 6.634128] after pairA output = ff [ 6.639613] before pairB output = d [ 6.645169] after pairB output = ff [ 6.650652] before pairC output = e [ 6.656215] after pairC output = 0 [ 6.661612] before pairD output = 1e [ 6.667263] after pairD output = 1 [ 6.670965] mt753x gsw@0: -------- gephy-calbration (port:2) -------- [ 6.687668] CALDLY = 40 [ 6.765221] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 6.839148] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 6.912676] GE R50 AnaCal Done! (11) (0x31)(0xb1) [ 6.980968] GE R50 AnaCal Done! (10) (0x32)(0xb2) [ 6.989292] GE 1e_174(0xb0b1), 1e_175(0xb1b2) [ 7.037073] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 7.064854] GE Tx offset AnaCal Done! (pair-1)(2)(0x2) 0x1e_172=0x2202 [ 7.103126] GE Tx offset AnaCal Done! (pair-2)(4)(0x23) 0x1e_173=0x2320 [ 7.136162] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x2303 [ 7.234726] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x741d) [ 7.297535] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c) [ 7.338098] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1a22) [ 7.385172] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1a22) [ 7.438416] PORT 2 RX_DC_OFFSET [ 7.452623] before pairA output = f [ 7.458167] after pairA output = 0 [ 7.463551] before pairB output = 1d [ 7.469166] after pairB output = 0 [ 7.474543] before pairC output = 1d [ 7.480173] after pairC output = 1 [ 7.485547] before pairD output = e [ 7.491092] after pairD output = 0 [ 7.494791] mt753x gsw@0: -------- gephy-calbration (port:3) -------- [ 7.511413] CALDLY = 40 [ 7.593597] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 7.672403] GE R50 AnaCal Done! (12) (0x30)(0xb0) [ 7.756460] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 7.845849] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 7.854167] GE 1e_174(0xa6b0), 1e_175(0xa6a4) [ 7.891387] GE Tx offset AnaCal Done! (pair-0)(1)(0x20) 0x1e_172=0x2020 [ 7.929730] GE Tx offset AnaCal Done! (pair-1)(4)(0x23) 0x1e_172=0x2023 [ 7.962805] GE Tx offset AnaCal Done! (pair-2)(3)(0x22) 0x1e_173=0x2220 [ 7.995867] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x2203 [ 8.074803] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x681a) [ 8.150731] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1f1f) [ 8.230639] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2028) [ 8.277823] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1b23) [ 8.331124] PORT 3 RX_DC_OFFSET [ 8.345326] before pairA output = 1d [ 8.350957] after pairA output = 0 [ 8.356339] before pairB output = 1e [ 8.361964] after pairB output = ff [ 8.367422] before pairC output = e [ 8.372965] after pairC output = 0 [ 8.378340] before pairD output = e [ 8.383884] after pairD output = ff [ 8.387663] mt753x gsw@0: -------- gephy-calbration (port:4) -------- [ 8.404292] CALDLY = 40 [ 8.465314] GE R50 AnaCal Done! (9) (0x34)(0xb4) [ 8.528201] GE R50 AnaCal Done! (9) (0x34)(0xb4) [ 8.585805] GE R50 AnaCal Done! (8) (0x35)(0xb5) [ 8.648686] GE R50 AnaCal Done! (9) (0x34)(0xb4) [ 8.656916] GE 1e_174(0xb4b4), 1e_175(0xb5b4) [ 8.704670] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 8.727163] GE Tx offset AnaCal Done! (pair-1)(1)(0x1) 0x1e_172=0x2201 [ 8.749519] GE Tx offset AnaCal Done! (pair-2)(1)(0x1) 0x1e_173=0x120 [ 8.777125] GE Tx offset AnaCal Done! (pair-3)(2)(0x2) 0x1e_173=0x102 [ 8.855924] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x5816) [ 8.892466] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1616) [ 8.972408] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1018) [ 9.052323] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1018) [ 9.105568] PORT 4 RX_DC_OFFSET [ 9.119721] before pairA output = 1e [ 9.125351] after pairA output = ff [ 9.130815] before pairB output = e [ 9.136366] after pairB output = 1 [ 9.141742] before pairC output = 1e [ 9.147372] after pairC output = ff [ 9.152838] before pairD output = e [ 9.158381] after pairD output = ff [ 9.164490] [SPM] pwrap node has not register regmap [ 9.169890] regulator regulator.3: info->modeset_reg 0xc = 0x181c32a2 [ 9.177268] regulator regulator.3: info->modeset_reg 0xc = 0x101c32a2 [ 9.192190] VFS: Mounted root (squashfs filesystem) readonly on device 31:9. [ 9.201012] devtmpfs: mounted [ 9.204147] Freeing unused kernel memory: 360K [ 9.208601] This architecture does not have kernel memory protection. INIT: version 2.88 booting create r/w /etc folder create r/w /var folder run /usr/etc/rcS (project/etc.rcS) /etc/rcS.d/S01create-perst-part.sh:18: command not found: file Usage: mkfs.ext4 [-c|-l filename] [-b block-size] [-C cluster-size] [-i bytes-per-inode] [-I inode-size] [-J journal-options] [-G flex-group-size] [-N number-of-inodes] [-d root-directory] [-m reserved-blocks-percentage] [-o creator-os] [-g blocks-per-group] [-L volume-label] [-M last-mounted-directory] [-O feature[,...]] [-r fs-revision] [-E extended-option[,...]] [-t fs-type] [-T usage-type ] [-U UUID] [-e errors_behavior][-z undo_file] [-jnqvDFSV] device [blocks-count] Fuse filesystem already available. Mounting fuse control filesystem. Starting udev [ 11.024159] udevd[916]: starting version 3.2.5 [ 11.062951] udevd[917]: starting eudev-3.2.5 hwclock: settimeofday: Invalid argument cat: read error: Is a directory cat: read error: Is a directory cat: read error: Is a directory Starting mount /var/config: main: do jffs2_boot do_jffs2_mkdir: create folder /var/storage ok [ 12.678040] jffs2: CLEANMARKER node found at 0x00000000 has totlen 0xc != normal 0x0 [ 12.697338] jffs2: Empty flash at 0x00000080 ends at 0x00000800 [ 12.744005] jffs2: notice: (1481) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. do_jffs2_mount: 1st, mount /dev/mtdblock14 to /var/storage ok done Starting untar webui-dlink: done Starting paccess: read_psec2datfile: done! done Starting csman: [csmsal_open]feed_csiddata (/tmp/csman/pre1.dat:5293) [csmsal_open]feed_csiddata (/tmp/csman/pre4.dat:549) [csmsal_open]feed_csiddata (/tmp/csman/pre7.dat:466) hookcs_load[183]: section_tag cmark:0x07 secid:0x07 magic:0x2B24 ts:0x00000012 imglen:0x00005BC8 imgchk:0xD80C tagchk:0x99ED [hookcs_load] C Area img Icksum() OK!(D80C)(D80C)(5BC8) hookcs_load[183]: section_tag cmark:0x07 secid:0x07 magic:0x2B24 ts:0x00000011 imglen:0x00005BD9 imgchk:0x7F9A tagchk:0xF24F [hookcs_load] C Area img Icksum() OK!(7F9A)(7F9A)(5BD9) C section 1 is up to date, load C section 1... [csmsal_open]feed_csiddata csection [csm_svr_init]csmsal open("/tmp/csman"), fd=171 done Starting syslogd/klogd: done fs.protected_hardlinks = 1 fs.protected_symlinks = 1 mount: /sys/kernel/debug: none already mounted or mount point busy. insmod: ERROR: could not insert module /lib/modules/4.4.124/extra/misc_gpioled.ko: File exists Starting commander: /dev/mf_dev Fri Apr 22 12:11:33 UTC 2022 [ 18.662309] mediatek-mt7622-pinctrl 10005000.pinctrl: pin MDI_RN_P0 already requested by 10005000.pinctrl:463; cannot claim for 10005000.pinctrl:463 [ 18.675660] mediatek-mt7622-pinctrl 10005000.pinctrl: pin-54 (10005000.pinctrl:463) status -22 [ 18.684290] <misc>gpio_led_set: cannot get gpio54 through pinctrl_request_gpio [ 18.945668] mediatek-mt7622-pinctrl 10005000.pinctrl: pin MDI_RN_P0 already requested by 10005000.pinctrl:463; cannot claim for 10005000.pinctrl:463 [ 18.959024] mediatek-mt7622-pinctrl 10005000.pinctrl: pin-54 (10005000.pinctrl:463) status -22 [ 18.967651] <misc>gpio_led_set: cannot get gpio54 through pinctrl_request_gpio Ether WAN NUM = 1 WAN = << WAN_MAC >> LAN = << LAN_MAC >> WLAN0 = << WLAN0_MAC >> WLAN1 = << WLAN1_MAC >> WLAN2 = << WLAN2_MAC >> WLAN3 = << WLAN3_MAC >> WLAN4 = << WLAN4_MAC >> WLAN5 = << WLAN5_MAC >> WLAN6 = << WLAN6_MAC >> WLAN7 = << WLAN7_MAC >> BEID STATUS : 0 , STATUS OK! ifconfig: SIOCGIFFLAGS: No such device [vlan] vlan - v1.0.3 [vlan] vlan Start [vlan] Complete Cmd WAN = << WAN_MAC >> LAN = << LAN_MAC >> WLAN0 = << WLAN0_MAC >> WLAN1 = << WLAN1_MAC >> WLAN2 = << WLAN2_MAC >> WLAN3 = << WLAN3_MAC >> WLAN4 = << WLAN4_MAC >> WLAN5 = << WLAN5_MAC >> WLAN6 = << WLAN6_MAC >> WLAN7 = << WLAN7_MAC >> BEID STATUS : 0 , STATUS OK! [vlan] Interface br0 Have Down ifconfig: SIOCGIFFLAGS: No such device [vlan] Interface brx0 Have Down [vlan] Brx Interface brx0 Down bridge brx0 doesn't exist; can't delete it ifconfig: SIOCGIFFLAGS: No such device [vlan] Interface brx1 Have Down [vlan] Brx Interface brx1 Down bridge brx1 doesn't exist; can't delete it [vlan] Interface eth0.1 Have Down [vlan] Interface eth0.3 Have Down [vlan] Interface eth0.4 Have Down [vlan] triple play = 0 [vlan] wanNum = 1, lanNum = 2, virturalwanNum = 0 [vlan] wanIndex = 0, lanIndex = 1, virtualwanIndex = 3 [vlan] wan port map: 0 [vlan] i = 0 position = 0 type = 1 portIndex = 0 portLogic = 0 portPhyId = 4 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 [vlan] i = 0 wanMac = << WAN_MAC >> [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 wanInterface = eth0.2 [vlan] i = 0 portInterface = eth0 [vlan] lan port map: 1 2 -1 [vlan] i = 1 position = 1 type = 2 portIndex = 1 portLogic = 1 portPhyId = 3 [vlan] i = 1 lanIndex = 0 [vlan] i = 1 lanMac = << LAN_MAC >> [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 lanInterface = [vlan] i = 2 position = 2 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 [vlan] i = 2 lanIndex = 1 [vlan] i = 2 lanMac = << LAN_MAC >> [vlan] i = 2 portMac = 000000000000 [vlan] i = 2 portInterface = eth0 [vlan] i = 2 lanInterface = [vlan] i = 1 lanInterface = eth0.1 [vlan] i = 2 lanInterface = eth0.1 [vlan] Vlan First Run Added VLAN with VID == 1 to IF -:eth0:- WARNING: VLAN 1 does not work with many switches, consider another number if you have problems. Added VLAN with VID == 2 to IF -:eth0:- set hello timer failed: Numerical result out of range [ 20.346634] device eth0.1 entered promiscuous mode ifconfig: SIOCSIFFLAGS: Network is down [vlan] Interface eth0.1 Have Down [ 20.370949] IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready [vlan] Interface br0 Have Up [vlan] Br Interface br0 Up ifconfig: SIOCSIFFLAGS: Network is down [vlan] Interface eth0.2 Have Down ifconfig: SIOCSIFFLAGS: Network is down [vlan] Interface eth0.2 Have Down REG_ATC_ADDR is 0x7ff0002 done. killall: mapd: no process killed killall: p1905_managerd: no process killed killall: wapp: no process killed [vlan] vlan End NETWORK Initialization finished. Result: 1 init watchdog init vlan init lan Init Lan init stp init ondemand init multiwan Initialize MultiWAN wantype = 0, wantype index = 99, wan mode = 1, route enable = 1 fo enable = 0, fo stay enable = 0, fo trigger = 0, fo time = 0, fo sequence = 0 init multi_ondemand init load_balance init spap init ddns init snmp SNMP Enterprise Number = 12823 SNMP Enterprise Name = SNMP Enterprise OID = 1.3.6.1.4.1.12823 SNMP Version: 5.8 zsh:1: command not found: snmpd-action init time Get time from RTC(ds3232) [ 22.543530] rtc-ds3232: probe of 1-0068 failed with error -110 [ 22.549393] i2c i2c-1: new_device: Instantiated device ds3232 at 0x68 init user cat: can't open '/etc/passwd.tmp': No such file or directory init dhcpsrv [ 22.898488] device eth0 entered promiscuous mode [ 22.903234] br0: port 1(eth0.1) entered forwarding state [ 22.908571] br0: port 1(eth0.1) entered forwarding state [ 22.914061] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready ifconfig: SIOCGIFFLAGS: No such device device br0 already exists; can't create bridge with the same name IP = 192.168.000.001 Mask = 255.255.255.000 (ffffff00) - aka /24 IP range start = 192.168.0.1 IP range end = 192.168.0.254 DHCP Server IP pool start = 192.168.0.100 DHCP Server IP pool end = 192.168.0.249 sip : 1, eip : 254 ptr_ip_start : 100 , ptr_ip_end : 249 DHCP Server IP pool OKOK!! BusyBox v1.27.2 (2022-04-15 10:19:47 UTC) multi-call binary. Usage: rm [-irf] FILE... dnsmasq config start dnsmasq config end Start Dnsmasq DHCP at init init dnsrelay init routing sh: can't open input file: /var/run/tagbase_bind_wan.clr rm: can't remove '/var/run/tagbase_bind_wan.clr': No such file or directory init route_protocol init nat init keepalive init syslog_interval_timer init schedule init load_balance init ftp_alg init rtsp_alg start the RTSP ALG modules [ 23.977915] nf_conntrack_rtsp v0.7 loading ==NAT Stop wan999 ALL== NAT nat-draft stop rule start [ 23.997776] nf_nat_rtsp v0.7 loading handle_rtsp_alg: load RTSP ALG modules init qos init reboot init reset_btn init sshd spi_exception_deinit start init sip_alg init https init wireless_mode module 1 INIT AP ROUTER MODE Module One AP ROUTER MODE module 2 INIT AP ROUTER MODE Module Two AP ROUTER MODE dnsmasq config start spi end clear /usr/bin/spi spi_exception_deinit mmi_nat_stop mmi_nat_start NAT nat-draft stop rule end ==NAT Start wan999 ALL== NAT nat-draft stop rule start spi_exception_deinit start spi end clear /usr/bin/spi spi_exception_deinit mmi_nat_stop dnsmasq config end init wlanap mmi_nat_start NAT nat-draft stop rule end NAT nat-draft start rule start All Log Alert options from Firewall are disable. nat-draft stop_ip_forward start nat-draft stop_ip_forward end mwlb start mwlb end admin start admin end virtual computer start virtual computer end wanalias start wanalias end portfwd start portfwd end Single DMZ start nat_info.wan_index == 999 mac-control start mac-control end discard_ping start discard_ping end inblkwpkts start [ 24.638300] ip6_tables: (C) 2000-2006 Netfilter Core Team inblkwpkts end adjust_mss start adjust_mss end fwd-recent start fwd-recent end NAT alg start NAT alg end pkt-filter start pkt-filter end pkt-filterv6 start pkt-filterv6 end l7appblk start l7appblk end url-block start fwd_block_url_file_extension url-block end url-block start fwd_block_url url-block end nat-draft start_ip_forward start sh /var/nat/ip_forward.clr nat-draft start_ip_forward end stealth-mode start [ 25.622332] pci 0000:00:00.0: BAR 0: assigned [mem 0x18000000-0x180fffff 64bit] [ 25.629699] pci 0000:00:00.0: BAR 0: error updating (0x18000004 != 0x000004) [ 25.636769] pci 0000:00:00.0: BAR 2: no space for [mem size 0x00000010] [ 25.643396] pci 0000:00:00.0: BAR 2: failed to assign [mem size 0x00000010] [ 25.650368] pci 0000:00:00.0: BAR 3: no space for [mem size 0x00000010] [ 25.657000] pci 0000:00:00.0: BAR 3: failed to assign [mem size 0x00000010] [ 25.663973] pci 0000:00:00.0: BAR 4: no space for [mem size 0x00000010] [ 25.670612] pci 0000:00:00.0: BAR 4: failed to assign [mem size 0x00000010] [ 25.677583] pci 0000:00:00.0: BAR 5: no space for [mem size 0x00000010] [ 25.684214] pci 0000:00:00.0: BAR 5: failed to assign [mem size 0x00000010] [ 25.691336] pci 0001:01:00.0: [14c3:7915] type 00 class 0x000280 [ 25.697736] pci 0001:01:00.0: reg 0x10: [mem 0x20000000-0x200fffff 64bit pref] [ 25.705088] pci 0001:01:00.0: reg 0x18: [mem 0x20100000-0x20103fff 64bit pref] [ 25.712444] pci 0001:01:00.0: reg 0x20: [mem 0x20104000-0x20104fff 64bit pref] [ 25.720290] pci 0001:01:00.0: supports D1 D2 [ 25.724569] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 25.731883] pci 0001:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] [ 25.739741] pci 0001:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] [ 25.747595] pci 0001:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] get_wifi_module_info can not find cisd(8000F500) on Psetion can not find cisd(8000F501) on Psetion init wpa init wlanapcli_profile Initial WLANAPCLI_PROFILE init iom zsh:1: command not found: event_managed init wan_led init status_led init igmp zsh:1: no such file or directory: /proc/tc3162/switch_reg init mupnpd init recent init bonjour init dnscrypt_proxy init aplan init pptp init pptpserv init l2tp init l2tpserv init gre init ipsec init x509 init scep init dns_redirect init vrrp init ntpsrv init ipv6 init v6filter init ddnsv6 init grouping init data_logging init recieve_alter_mode init guestzone init mesh init mydlink [ 25.946040] jffs2: CLEANMARKER node found at 0x00000000 has totlen 0xc != normal 0x0 [ 25.966602] jffs2: CLEANMARKER node found at 0x00020000 has totlen 0xc != normal 0x0 [ 25.986893] jffs2: CLEANMARKER node found at 0x00040000 has totlen 0xc != normal 0x0 [ 26.034679] jffs2: notice: (2014) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. read_csid2rawfile: done! read_csid2rawfile: done! stealth-mode end spi_exception_deinit start spi end spi_exception_init start spi end pre_spi_mode start spi end security_v6 start security_v6 end Conntrack -F start Wait 2 seconds init WPS init ClientInfo init dlink_fota init dlink_speedtest read_csid2rawfile: done! read_csid2rawfile: done! size=16384 num=64 uir_thread_count=80 select timeout=10 0 done Configuring packages on first boot.... (This may take several minutes. Please do not power off the machine.) Create regular thread: watchdog Create regular thread: time WiFi Module One Operation Mode is changed WiFi Module Two Operation Mode is changed WiFi Operation Mode is Changed and Apply Wirelessmode Alter from Commander Disable WAN bridges to LAN device eth0.2 is not a slave of br0 Configuring dhcp-server. Sorry, rule does not exist. Module One AP ROUTER MODE Module Two AP ROUTER MODE zsh:1: command not found: vlantag2 [ 28.707485] watchdog watchdog0: watchdog did not stop! Adding system startup for /etc/init.d/dhcp-server. dnsmasq config start dnsmasq config end Configuring dnsmasq. update-rc.d: /etc/init.d/dnsmasq: file does not exist Configuring keepalived. update-rc.d: /etc/init.d/keepalived exists during rc.d purge (use -f to force) Configuring vsftpd. wlan_phase_two_config killall: rt2860apd: no process killed Wireless 8021X Stop Disable WLAN interface. WLAN One interface down! killall: mosquitto: no process killed ifconfig: SIOCGIFFLAGS: No such device killall: EasyMeshDaemon: no process killed killall: emhandler: no process killed killall: emLooping: no process killed interface ra0 does not exist! killall: emDiscovery: no process killed killall: mapd: no process killed ifconfig: SIOCGIFFLAGS: No such device killall: p1905_managerd: no process killed killall: wapp: no process killed rmmod: ERROR: Module mapfilter is not currently loaded killall: bs20: no process killed interface ra1 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wds0 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wds1 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wds2 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wds3 does not exist! ifconfig: SIOCGIFFLAGS: No such device WLAN Two interface down! ifconfig: SIOCGIFFLAGS: No such device interface rai0 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface rai1 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wdsi0 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wdsi1 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wdsi2 does not exist! ifconfig: SIOCGIFFLAGS: No such device interface wdsi3 does not exist! ifconfig: SIOCGIFFLAGS: No such device rmmod: ERROR: Module mt_whnat is not currently loaded killall: fwdd: no process killed rmmod: ERROR: Module mtfwd is not currently loaded rmmod: ERROR: Module mt_wifi_ap is not currently loaded rmmod: ERROR: Module mt7915_mt_wifi_ap is not currently loaded killall: ACSDaemon: no process killed Enable WLAN interface. assigned dat_path:/etc/Wireless/RT2860AP/l1profile.dat dat_path:/etc/Wireless/RT2860AP/l1profile.dat assigned dat_path:/etc/Wireless/RT2860AP/RT2860AP1.dat assigned csid_index:1 dat_path:/etc/Wireless/RT2860AP/RT2860AP1.dat assigned dat_path:/etc/Wireless/RT2860AP/RT2860AP2.dat assigned csid_index:2 dat_path:/etc/Wireless/RT2860AP/RT2860AP2.dat [ 29.815765] mediatek_soc_hnat 1b100000.hnat: wan = eth0.2 [ 29.822258] mediatek_soc_hnat 1b100000.hnat: lan = eth0.1 [ 29.828075] mediatek_soc_hnat 1b100000.hnat: ppd = eth0.1 [ 29.833559] mediatek_soc_hnat 1b100000.hnat: gmac num = 1 [ 29.839955] mediatek_soc_hnat 1b100000.hnat: FOE entry number = 8192 [ 29.846901] mediatek_soc_hnat 1b100000.hnat: hwnat start cat: read error: Is a directory cat: read error: Is a directory cat: read error: Is a directory Undefined users: > quagga Skipping /etc/default/volatiles/volatiles.03_quagga Undefined users: > radvd Skipping /etc/default/volatiles/volatiles.03_radvd update-rc.d: /etc/init.d/vsftpd: file does not exist INIT: Entering runlevel: 5 Configuring network interfaces... RTNETLINK answers: File exists Starting OpenBSD Secure Shell server: sshd Conntrack -F end generating ssh RSA host key... NAT nat-draft stop rule end [ 30.448035] mt_wifi_ap: module license 'Proprietary' taints kernel. [ 30.454345] Disabling lock debugging due to kernel taint [ 30.483328] register mt_drv [ 30.490396] [ 30.490396] == pAd = ffffff8009501000, size = 7020416, Status=0 == [ 30.498079] AP Driver version-5.1.0.0 [ 30.502276] read sub id = 2 [ 30.505124] Use 1st ePAeLNA default bin. [ 30.509232] Use 1st /etc_ro/wlan/MT7622_EEPROM.bin default bin. [ 30.515166] <--mt7622_init() [ 30.518880] <-- RTMPAllocTxRxRingMemory, Status=0 generating ssh ECDSA host key... generating ssh ED25519 host key... done. Error: There is no config file for conntrackd Starting DHCP server: . Starting ntpd: done /etc/rc5.d/S20xl2tpd:.:23: no such file or directory: /lib/lsb/init-functions chgrp: unknown group adm mv: can't rename 'boot.0': No such file or directory [ 31.737870] register mt_drv [ 31.741602] mt_drv 0001:01:00.0: enabling device (0000 -> 0002) [ 31.763187] [ 31.763187] [ 31.763187] === pAd = ffffff800a901000, size = 29657728 === [ 31.763187] [ 31.775392] <-- RTMPAllocAdapterBlock, Status=0 [ 31.780529] PCI CSRBaseAddress =0xffffff800a800000, csr_addr=0xffffff800a800000! [ 31.788034] RTMPInitPCIeDevice():device_id=0x7915 [ 31.792871] mt7915_init()--> [ 31.795763] Use 1st iPAiLNA default bin. [ 31.799769] <--mt7915_init() [ 31.804996] wdev_init(caller:RTMP_COM_IoctlHandle+0x348/0x1700 [mt7915_mt_wifi_ap]), wdev(0) [ 31.813815] Rx[0] Ring: total 24576 bytes allocated [ 31.818783] Rx[1] Ring: total 24576 bytes allocated [ 31.824155] Rx[2] Ring: total 8192 bytes allocated [ 31.829830] Rx[3] Ring: total 16384 bytes allocated [ 31.835182] Rx[4] Ring: total 8192 bytes allocated [ 31.840003] <-- pci_alloc_tx_rx_ring_mem, Status=0 [ 31.868140] whnat_module_init(): module init and register callback for whnat [ 31.875238] create whnat_ctrl ok!!! [ 31.878847] wed_slot_map_get(): assign slot_id:0 for entry: 0! [ 31.878862] wed_slot_map_get(): assign slot_id:1 for entry: 1! WLAN One interfa[ 31.878954] whnat_hif_pcie_mirror_probe(): hif_cfg base addr=ffffff80093c4400 ce up! dlinkdistro (Yocto Project Reference Distro) 2.5.1 M32-D002 /dev/ttyS0 [ 31.905479] ra0: ===> main_virtual_if_open M32-D002 login:[ 31.911260] load l1profile succeed! [ 32.219096] APWdsInitialize():WdsEntry Number=4 [ 32.224492] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860_5G.dat [ 32.231902] Open file "/etc/Wireless/RT2860/RT2860_5G.dat" failed! [ 32.238285] CfgSetCountryRegion():region(255) out of range! [ 32.244099] RTMPSetProfileParameters,0-0-1-FC:A5:D0:00:00:00;0-0-1-34:29:8F:00:00:00;0-0-1-48:E1:E9:00:00:00 [ 32.253929] RTMPSetProfileParameters,0-0-1-FC:A5:D0:00:00:00 [ 32.259601] SET IOT-STA: BAND[0] MACTYPE(0) HANDLE(1) MAC[fc:a5:d0:0:0:0] [ 32.266388] RTMPSetProfileParameters,0-0-1-34:29:8F:00:00:00 [ 32.272054] SET IOT-STA: BAND[0] MACTYPE(0) HANDLE(1) MAC[34:29:8f:0:0:0] [ 32.278841] RTMPSetProfileParameters,0-0-1-48:E1:E9:00:00:00 [ 32.284507] SET IOT-STA: BAND[0] MACTYPE(0) HANDLE(1) MAC[48:e1:e9:0:0:0] [ 32.291355] SSID[0]=M32-D002, EdcaIdx=0 [ 32.295249] SSID[1]=M32-backhaul-D002, EdcaIdx=0 [ 32.299949] DBDC Mode=0, eDBDC_mode = 0 [ 32.303798] BSS0 PhyMode=14 [ 32.306589] wmode_band_equal(): Band Equal! [ 32.310799] auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 1 [ 32.318979] auto_ch_select_set_cfg(): BandIdx1, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 32.327620] BandSteering=1 [ 32.330406] [TxPower] BAND0: 100 [ 32.334421] [PERCENTAGEenable] BAND0: 1 [ 32.338354] [BFBACKOFFenable] BAND0: 1 [ 32.342331] FragThreshold[0]=2346 [ 32.347493] RTMPSetProfileParameters(): ACSCheckTime[0]=0 seconds [ 32.353589] RTMPSetProfileParameters(): ACSCheckTime[1]=0 seconds [ 32.360118] read_etxbf: ETxBfEnCond = 1 [ 32.363961] read_etxbf: BSSID[0] [ 32.367181] read_etxbf: MBSS[0] ETxBfEnCond = 1 [ 32.371719] read_etxbf: More BSSID[1] [ 32.375375] read_etxbf: More MBSS[1] ETxBfEnCond = 1 [ 32.385637] MAP_MODE=1 [ 32.391376] If/wds0 - PeerPhyOpMode=2 [ 32.395046] If/wds1 - PeerPhyOpMode=2 [ 32.398708] If/wds2 - PeerPhyOpMode=2 [ 32.402376] If/wds3 - PeerPhyOpMode=2 [ 32.406246] APWdsInitialize():WdsEntry Number=4 [ 32.410781] WDS-Enable mode=0 [ 32.414812] HT: WDEV[0] Ext Channel = ABOVE [ 32.419122] HT: greenap_cap = 0 [ 32.434506] WtcSetMaxStaNum: BssidNum:2, MaxStaNum:124 (WdsNum:4, ApcliNum:1, MaxNumChipRept:16), MinMcastWcid:125 [ 32.444996] Fair Queueing Scheduler Initialization... [ 32.450200] Top Init Done! [ 32.452914] Use dev_alloc_skb [ 32.456289] RX[0] DESC ffffffc0162c0000 size = 8192 [ 32.461316] RX[1] DESC ffffffc0162c2000 size = 8192 [ 32.466295] cut_through_init(): ct sw token number = 4095 [ 32.471819] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 32.479567] cut_through_token_list_init(): ffffffc0129fca10,ffffffc0129fca10 [ 32.486735] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 [ 32.494491] cut_through_token_list_init(): ffffffc0129fca30,ffffffc0129fca30 [ 32.501625] Hif Init Done! [ 32.504339] ctl->txq = ffffff8009b77600 [ 32.508180] ctl->rxq = ffffff8009b77618 [ 32.512021] ctl->ackq = ffffff8009b77630 [ 32.515945] ctl->kickq = ffffff8009b77648 [ 32.519958] ctl->tx_doneq = ffffff8009b77660 [ 32.524229] ctl->rx_doneq = ffffff8009b77678 [ 32.545976] Parsing patch header [ 32.549233] Built date: 20200821025910a [ 32.553236] [ 32.554719] Platform: ALPS [ 32.557542] HW/SW version: 0x8a108a10 [ 32.561322] Patch version: 0x00000010 [ 32.565106] Target address: 0x9c000, length: 82080 [ 32.570151] patch is not ready && get semaphore success [ 32.575441] EventGenericEventHandler: CMD Success [ 32.580658] MtCmdPatchFinishReq [ 32.595057] EventGenericEventHandler: CMD Success [ 32.599801] release patch semaphore [ 32.603291] WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 [ 32.609578] Parsing CPU 0 fw tailer [ 32.613069] Chip ID: 0x06 [ 32.615792] Eco version: 0x00 [ 32.618850] Region number: 0x00 [ 32.622099] Format version: 0x00 [ 32.625432] Ram version: _reserved_ [ 32.629064] Built date: 20200821030117 [ 32.633065] Common crc: 0x0 [ 32.635951] Parsing tailer region 0 [ 32.639441] Feature set: 0x01 [ 32.642501] Target address: 0xb7000, Download size: 249856 [ 32.648078] Parsing tailer region 1 [ 32.651566] Feature set: 0x01 [ 32.654625] Target address: 0x203dc00, Download size: 50384 [ 32.660330] EventGenericEventHandler: CMD Success [ 32.669043] EventGenericEventHandler: CMD Success [ 32.674150] MtCmdFwStartReq: override = 0x0, address = 0x0 [ 32.721151] EventGenericEventHandler: CMD Success [ 32.725866] MCU Init Done! [ 32.728585] efuse_probe: efuse = 2 [ 32.731993] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4 [ 32.737390] RtmpEepromGetDefault::e2p_dafault=2 [ 32.741924] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 [ 32.749494] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] [ 32.755609] NICReadEEPROMParameters: EEPROM 0x52 b300 [ 32.761368] mt7622_pa_lna_set(): read antCtrl = 2, polCtrl = 0, wifiStreams = 44 [ 32.769018] mt7622_tssi_set(): nic_cfg1=0, mode=0 [ 34.000140] Country Region from e2p = 0 [ 34.004062] read sub id = 2 [ 34.006854] RcRadioInit(): DbdcMode=0, ConcurrentBand=1 [ 34.012086] RcRadioInit(): pRadioCtrl=ffffffc016df11d8,Band=0,rfcap=1,channel=1,PhyMode=2 extCha=0xf [ 34.021230] MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! [ 34.027462] MtBfBackOffLoadParam: RF_LOCKDOWN Feature OFF !!! [ 34.033344] EEPROM Init Done! [ 34.036325] mt_mac_init()--> [ 34.039206] mt7622_init_mac_cr(): TMAC_TRCR0=0x82783c8c [ 34.044450] <--mt_mac_init() [ 34.065907] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 34.082964] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 34.100020] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 34.106549] MAC Init Done! [ 34.109259] MT7622BBPInit() todo [ 34.112490] PHY Init Done! [ 34.115808] MtCmdSetMacTxRx:(ret = 0) [ 34.119614] ap_ftkd> Initialize FT KDP Module... [ 34.124242] BndStrg_Init() BndStrg_TableInit(),Invalid Channel:0 pMbss apidx:0 [ 34.132566] Error in BndStrg_Init(), error code = 9 on apidx = 0 [ 34.138588] Main bssid = 00:00:00:00:00:00 [ 34.142860] MtCmdSetMacTxRx:(ret = 0) [ 34.153826] MtCmdSetMacTxRx:(ret = 0) [ 34.157500] <==== mt_wifi_init, Status=0 [ 34.161436] TxBfModuleEnCtrl:It's not DBDC mode [ 34.166018] MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 0 [ 34.171007] MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 [ 34.176690] The new WDS interface MAC = 00:00:00:00:00:00, MacTabMatchWCID = 0 [ 34.184598] The new WDS interface MAC = 00:00:00:00:00:00, MacTabMatchWCID = 0 [ 34.192341] The new WDS interface MAC = 00:00:00:00:00:00, MacTabMatchWCID = 0 [ 34.200101] The new WDS interface MAC = 00:00:00:00:00:00, MacTabMatchWCID = 0 [ 34.207855] Total allocated 4 WDS interfaces! [ 34.212704] WtcSetMaxStaNum: BssidNum:2, MaxStaNum:124 (WdsNum:4, ApcliNum:1, MaxNumChipRept:16), MinMcastWcid:125 [ 34.247844] RedInit: set Driver/N9 RED Enable to 1. [ 34.252747] RedInit: RED Initiailize Done. [ 34.256847] cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2. [ 34.263124] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 34.269404] wifi_sys_open(), wdev idx = 0 [ 34.273418] wdev_attr_update(): wdevId0 = << WLAN0_MAC >> [ 34.278996] [RcGetHdevByPhyMode] channel 0 fix for rdev fetching [ 34.285080] [RadarStateCheck] RD_NORMAL_MODE [ 34.290485] phy_freq_adjust : no prim_ch value for adjust! [ 34.297239] Caller: wlan_operate_init+0xdc/0x118 [mt_wifi_ap] [ 34.303016] phy_mode=14, ch=0, wdev_type=1 [ 34.307116] ht_cap->HtCapInfo: ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0 [ 34.316429] ht_cap->HtCapParm: mdpu_density=5, ampdu_factor=3 [ 34.324996] AP inf up for ra_0(func_idx) OmacIdx=0 [ 34.332107] mtd_isr::DriverOwn = TRUE [ 34.335795] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 34.347224] ApAutoChannelAtBootUp-----------------> [ 34.352120] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 [ 34.357870] MtCmdSetMacTxRx:(ret = 0) [ 34.361555] MtCmdChannelSwitch: control_chl = 1,control_ch2=0, central_chl = 1 DBDCIdx= 0, Band= 0 [ 34.370519] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 34.607459] MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 [ 34.616437] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 34.847455] MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 34.856425] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.079464] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 [ 35.088434] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.311456] MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 [ 35.320422] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.543458] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 35.552425] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 35.775459] MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 [ 35.784430] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.019545] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 [ 36.028517] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.251457] MtCmdChannelSwitch: control_chl = 9,control_ch2=0, central_chl = 9 DBDCIdx= 0, Band= 0 [ 36.260426] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.467456] MtCmdChannelSwitch: control_chl = 10,control_ch2=0, central_chl = 10 DBDCIdx= 0, Band= 0 [ 36.476592] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.683457] MtCmdChannelSwitch: control_chl = 11,control_ch2=0, central_chl = 11 DBDCIdx= 0, Band= 0 [ 36.692595] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 36.899460] MtCmdChannelSwitch: control_chl = 12,control_ch2=0, central_chl = 12 DBDCIdx= 0, Band= 0 [ 36.908601] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 37.115464] MtCmdChannelSwitch: control_chl = 13,control_ch2=0, central_chl = 13 DBDCIdx= 0, Band= 0 [ 37.124648] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 37.331463] ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 1, IsAband = 0 [ 37.340004] AutoChSelUpdateChannel(): Update channel for wdev for this band PhyMode = 14, Channel = 1 [ 37.350112] MtCmdChannelSwitch: control_chl = 1,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 37.359070] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 37.383277] ApAutoChannelAtBootUp<----------------- [ 37.388189] [PMF]APPMFInit:: apidx=0, MFPC=1, MFPR=0, SHA256=0 [ 37.394034] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE [ 37.402636] wifi_sys_linkup(), wdev idx = 0 [ 37.406844] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 [ 37.406844] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 37.468634] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [ 37.528424] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 [ 37.534195] APStartUpForMbss: BssIndex = 0 channel = 1 [ 37.539376] MtCmdTxPowerDropCtrl: ucPowerDrop: 100, BandIdx: 0 [ 37.545226] MtCmdTxCCKStream: u1CCKTxStream: 1, BandIdx: 0 [ 37.552411] BndStrg_SetInfFlags(): BSS(<< WLAN0_MAC >>) set 2G Inf ra0 ready. Enable 20/40 BSSCoex Channel Scan(BssCoex=1) [ 37.565914] MtCmdSetMacTxRx:(ret = 0) [ 37.569593] MtCmdChannelSwitch: control_chl = 1,control_ch2=0, central_chl = 1 DBDCIdx= 0, Band= 0 [ 37.578557] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 37.602791] AP OBSS SYNC - BBP R4 to 20MHz.l [ 37.903455] MtCmdChannelSwitch: control_chl = 2,control_ch2=0, central_chl = 2 DBDCIdx= 0, Band= 0 [ 37.912420] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 37.936650] AP OBSS SYNC - BBP R4 to 20MHz.l [ 38.239452] MtCmdChannelSwitch: control_chl = 3,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 38.248424] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 38.272679] AP OBSS SYNC - BBP R4 to 20MHz.l [ 38.575456] MtCmdChannelSwitch: control_chl = 4,control_ch2=0, central_chl = 4 DBDCIdx= 0, Band= 0 [ 38.584423] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 38.608639] AP OBSS SYNC - BBP R4 to 20MHz.l [ 38.911455] MtCmdChannelSwitch: control_chl = 5,control_ch2=0, central_chl = 5 DBDCIdx= 0, Band= 0 [ 38.920419] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 38.944664] AP OBSS SYNC - BBP R4 to 20MHz.l [ 39.247460] MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 6 DBDCIdx= 0, Band= 0 [ 39.256431] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 39.280645] AP OBSS SYNC - BBP R4 to 20MHz.l [ 39.583456] MtCmdChannelSwitch: control_chl = 7,control_ch2=0, central_chl = 7 DBDCIdx= 0, Band= 0 [ 39.592433] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 39.616670] AP OBSS SYNC - BBP R4 to 20MHz.l [ 39.919456] MtCmdChannelSwitch: control_chl = 8,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 [ 39.928423] BW = 0,TXStream = 4, RXStream = 4, scan(1) [ 39.952664] AP OBSS SYNC - BBP R4 to 20MHz.l [ 40.255444] Channel[Idx=0, Ch=1].bEffectedChannel=0x2! [ 40.260596] Channel[Idx=1, Ch=2].bEffectedChannel=0x0! [ 40.265738] Channel[Idx=2, Ch=3].bEffectedChannel=0x0! [ 40.270879] Channel[Idx=3, Ch=4].bEffectedChannel=0x0! [ 40.276022] Channel[Idx=4, Ch=5].bEffectedChannel=0x2! [ 40.281163] needFallBack=TRUE due to OP/OT! [ 40.285352] Channel[Idx=5, Ch=6].bEffectedChannel=0x2! [ 40.290496] needFallBack=TRUE due to OP/OT! [ 40.294684] Channel[Idx=6, Ch=7].bEffectedChannel=0x0! [ 40.299825] Channel[Idx=7, Ch=8].bEffectedChannel=0x0! [ 40.304991] MtCmdChannelSwitch: control_chl = 1,control_ch2=0, central_chl = 3 DBDCIdx= 0, Band= 0 [ 40.313952] BW = 1,TXStream = 4, RXStream = 4, scan(0) [ 40.338225] apidx 0 for WscUUIDInit [ 40.341781] Generate UUID for apidx(0) [ 40.345565] mtk_ppe_dev_register_hook : ineterface ra0 register (1) [ 41.357242] device ra0 entered promiscuous mode [ 41.361829] br0: port 2(ra0) entered forwarding state [ 41.366897] br0: port 2(ra0) entered forwarding state Set multicast_to_unicast kernel option to 1 on interface eth0.1 Set multicast_to_unicast kernel option to 1 on interface ra0 ra0 Channel Value: 1 WLAN Two interface up! [ 41.449898] rai0: ===> main_virtual_if_open [ 41.454120] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 41.460880] load l1profile succeed! [ 41.464516] WHNAT=1 [ 41.466611] whnat_cap_support(): chip_id=7915 is in WHNAT support list [ 41.473181] wifi_slot_get(): bus name=PCI Bus 0001:01, funid=0, get slot id=0 [ 41.480334] whnat_entry_acquire(): PCIE SLOT:0, hook to WHNAT,entry id=0 [ 41.487248] wed_init(0): irq=11,base_addr=0xffffff80093f2000 [ 41.493836] wed_ring_init(): wed ring init result = 0 [ 41.509621] create wed ok!!! [ 41.512746] wdma_init(): wdma(0) base addr=ffffff80093fe800 [ 41.518347] wdma_init(): wdma(0) irq[0]=253 [ 41.522545] wdma_init(): wdma(0) irq[1]=254 [ 41.526739] wdma_init(): wdma(0) irq[2]=255 [ 41.531641] wifi_chip_probe(): Chang CHIP IRQ: 259 to WHNAT IRQ: 11 [ 41.537915] wifi_slot_get(): bus name=PCI Bus 0001:01, funid=0, get slot id=0 [ 41.545138] whnat_probe(): probe fail since whnat is full! [ 41.550638] whnat_dev0: probe of 1020a000.wed2 failed with error -1 [ 41.557079] mt_service_open: wlan service opens successfully! [ 41.565934] APWdsInitialize():WdsEntry[0~15] [ 41.571788] BssidNum=2 [ 41.574142] Pf2MbssIdxMap: [ 41.576856] 0 1 [ 41.579367] E2pAccessMode=2 [ 41.582314] SSID[0]=M32-D002, EdcaIdx=0 [ 41.586210] SSID[1]=M32-backhaul-D002, EdcaIdx=0 [ 41.590926] RTMPSetProfileParameters(): DBDC Mode=0, eDBDC_mode = 0 [ 41.597251] cfg_mode=17 [ 41.599703] cfg_mode=17 [ 41.602143] cfg_mode=17 [ 41.604597] wmode_band_equal(): Band Equal! [ 41.608887] auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 1 [ 41.617079] auto_ch_select_set_cfg(): BandIdx1, AutoChannelAtBootup=0, AutoChannelAlg = 0 [ 41.625350] Index0 Channel=0 [ 41.628558] BandSteering=1 [ 41.631353] [TxPower] BAND0: 100 [ 41.636016] [SKUenable] BAND0: 1 [ 41.639244] [SkuTableIdx]: 1 [ 41.642211] [CCKTxStream] BAND0: 4 [ 41.645625] [PERCENTAGEenable] BAND0: 1 [ 41.649473] [BFBACKOFFenable] BAND0: 1 [ 41.653387] [MaxRuOfdma] BAND0: 8 [ 41.656783] [MaxDLMuMimo] BAND0: 4 [ 41.660266] [MaxULMuMimo] BAND0: 2 [ 41.663817] profile: FragThreshold[0]=2346 [ 41.668185] APEdca0 [ 41.670363] APEdca1 [ 41.672555] APEdca2 [ 41.674730] APEdca3 [ 41.677562] UAPSDCapable[0]=0 [ 41.680528] UAPSDCapable[1]=0 [ 41.683501] UAPSDCapable[2]=0 [ 41.686461] UAPSDCapable[3]=0 [ 41.689430] UAPSDCapable[4]=0 [ 41.692398] UAPSDCapable[5]=0 [ 41.695358] UAPSDCapable[6]=0 [ 41.698329] UAPSDCapable[7]=0 [ 41.701297] UAPSDCapable[8]=0 [ 41.704268] UAPSDCapable[9]=0 [ 41.707227] UAPSDCapable[10]=0 [ 41.710284] UAPSDCapable[11]=0 [ 41.713336] UAPSDCapable[12]=0 [ 41.716402] UAPSDCapable[13]=0 [ 41.719456] UAPSDCapable[14]=0 [ 41.722502] UAPSDCapable[15]=0 [ 41.725562] UAPSDCapable[16]=0 [ 41.728613] UAPSDCapable[17]=0 [ 41.731722] UAPSDCapable[18]=0 [ 41.734768] UAPSDCapable[19]=0 [ 41.737828] UAPSDCapable[20]=0 [ 41.740883] UAPSDCapable[21]=0 [ 41.743941] UAPSDCapable[22]=0 [ 41.746987] UAPSDCapable[23]=0 [ 41.750045] UAPSDCapable[24]=0 [ 41.753096] UAPSDCapable[25]=0 [ 41.756155] UAPSDCapable[26]=0 [ 41.759202] UAPSDCapable[27]=0 [ 41.762258] UAPSDCapable[28]=0 [ 41.765313] UAPSDCapable[29]=0 [ 41.768370] UAPSDCapable[30]=0 [ 41.771420] UAPSDCapable[31]=0 [ 41.774482] default ApCliUAPSDCapable[0]=0 [ 41.778575] default ApCliUAPSDCapable[1]=0 [ 41.783370] DfsZeroWaitCacTime=255/255 [ 41.787141] RTMPSetProfileParameters(): ACSCheckTime[0]=0 seconds [ 41.793239] RTMPSetProfileParameters(): ACSCheckTime[1]=0 seconds [ 41.799506] read_itxbf: ITxBfEn = 0 [ 41.802987] read_itxbf: BSSID[0] [ 41.806219] read_itxbf: MBSS[0] ITxBfEn = 0 [ 41.810403] read_itxbf: More BSSID[1] [ 41.814065] read_itxbf: More MBSS[1] ITxBfEn = 0 [ 41.818690] read_itxbf: Common.ITxBfEn = 0 [ 41.822849] read_etxbf: ETxBfEnCond = 1 [ 41.826688] read_etxbf: BSSID[0] [ 41.829914] read_etxbf: MBSS[0] ETxBfEnCond = 1 [ 41.834499] read_etxbf: More BSSID[1] [ 41.838166] read_etxbf: More MBSS[1] ETxBfEnCond = 1 [ 41.843931] MBSS[0] MuOfdmaDlEnable = 1 [ 41.847768] More MBSS[1] MuOfdmaDlEnable = 1 [ 41.852124] MBSS[0] MuOfdmaUlEnable = 1 [ 41.855960] More MBSS[1] MuOfdmaUlEnable = 1 [ 41.860316] MBSS[0] MuMimoDlEnable = 1 [ 41.864066] More MBSS[1] MuMimoDlEnable = 1 [ 41.868338] MBSS[0] MuMimoUlEnable = 1 [ 41.872095] More MBSS[1] MuMimoUlEnable = 1 [ 41.884116] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1 [ 41.889693] [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=1 [ 41.895347] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [ 41.900919] [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0 [ 41.906574] [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [ 41.912754] [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0 [ 41.919457] MAP_MODE=1 [ 41.922193] ApCliEntry[0].Enable=0 [ 41.927071] rtmp_read_wds_from_file(): WDS Profile [ 41.931999] WDS Number: band[0]=0, band[1]=0 [ 41.936307] WDS-Enable mode=0 [ 41.939334] If/wds0 - PeerPhyMode=0x11 [ 41.943088] If/wds1 - PeerPhyMode=0x11 [ 41.946835] If/wds2 - PeerPhyMode=0x11 [ 41.950587] If/wds3 - PeerPhyMode=0x11 [ 41.955610] HT_BAWinSize: wdev[0]: (TX=256, RX=256) [ 41.960710] HT: WDEV[0] Ext Channel = ABOVE [ 41.965027] HT: greenap_cap = 0 [ 41.998423] rtmp_read_mlme_multiqueue_parms_from_file(): Mlme.MultiQEnable=1 [ 42.005558] rtmp_read_mlme_multiqueue_parms_from_file(): [hp_q_ration]-[np_q_ration]-[lp_q_ration] = 8-4-1 [ 42.015315] WtcSetMaxStaNum: MaxStaNum:236, BssidNum:2, WdsNum:16, MSTANum:1, MaxNumChipRept:32, MinMcastWcid:285 [ 42.025612] Top Init Done! [ 42.028347] Use dev_alloc_skb [ 42.031309] token_tx_queue_init(): ct sw token number = 1023 [ 42.037100] token_tx_queue_init(): token que inited done!id_head/tail=0/1024 [ 42.044155] token_tx_queue_init(): ffffffc01df0d208,ffffffc01df0d208 [ 42.052043] TxRing[0]: attr:0, total 2048 entry initialized [ 42.058437] TxRing[1]: attr:0, total 2048 entry initialized [ 42.064161] RX[0] DESC ffffff8009389000 size = 24576 [ 42.070203] RX[1] DESC ffffff8009390000 size = 24576 [ 42.076281] RX[2] DESC ffffff8009397000 size = 8192 [ 42.081511] RX[3] DESC ffffff800939a000 size = 16384 [ 42.087193] RX[4] DESC ffffff800939f000 size = 8192 [ 42.092658] -->TX_RING_0[0xd7300]: Attr:0, Base=0x52a20000, Cnt=2048! [ 42.099168] -->TX_RING_1[0xd7310]: Attr:0, Base=0x52af8000, Cnt=2048! [ 42.105667] -->TX_RING_2[0xd5400]: Attr:3, Base=0x529f7000, Cnt=128! [ 42.112067] -->TX_RING_3[0xd5410]: Attr:2, Base=0x529f8000, Cnt=256! [ 42.118433] -->TX_RING_4[0xd5440]: Attr:1, Base=0x529f9000, Cnt=256! [ 42.124808] -->RX_RING_0[0xd4500]: Base=0x52b80000, Cnt=1536 [ 42.130472] -->RX_RING_1[0xd4510]: Base=0x52b88000, Cnt=1536 [ 42.136215] -->RX_RING_2[0xd5500]: Base=0x52a0c000, Cnt=512 [ 42.141796] -->RX_RING_3[0xd7410]: Base=0x55c94000, Cnt=1024 [ 42.147456] -->RX_RING_4[0xd5520]: Base=0x52a0e000, Cnt=512 [ 42.153041] wdma_dma_ctrl(): WDMA_GLO_CFG=40000450 [ 42.157867] Hif Init Done! [ 42.163695] pci_driver_own_by_port: success to clear p=0 fw own, from(1): 1 is interrupt mode, 2 is polling mode. [ 42.173958] driver_own: port=1 is not enabled [ 42.178323] fw_prepare():using E2 ROM patch [ 42.182509] fw_prepare():using E2 RAM [ 42.186191] Parsing patch header [ 42.189421] Built date: 20201105222230a [ 42.193421] [ 42.194904] Platform: ALPS [ 42.197726] HW/SW version: 0x8a108a10 [ 42.201507] Patch version: 0xffffffff [ 42.205289] Section num: 0x2, subsys: 0x4 [ 42.209394] Section 0: type = 0x30002, offset = 0xe0, size = 0xfc90 [ 42.215749] Target address: 0x200000, length: 0xfc90 [ 42.220806] Section 1: type = 0x30002, offset = 0xfd70, size = 0x13720 [ 42.227446] Target address: 0xe000f000, length: 0x13720 [ 42.232913] Patch SEM Status = 2 [ 42.236177] patch is not ready && get semaphore success [ 42.241454] Start address = 0x200000, DL length = 64656, Data mode = 0x80000000 [ 42.249951] EventGenericEventHandler: CMD Success [ 42.254675] MtCmdAddressLenReq:(ret = 0) [ 42.258891] Start address = 0xe000f000, DL length = 79648, Data mode = 0x80000000 [ 42.267549] EventGenericEventHandler: CMD Success [ 42.272286] MtCmdAddressLenReq:(ret = 0) [ 42.276709] MtCmdPatchFinishReq [ 42.283646] EventGenericEventHandler: CMD Success [ 42.288569] Patch SEM Status = 3 [ 42.291809] release patch semaphore [ 42.295293] WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 [ 42.302450] Parsing CPU 0 fw tailer [ 42.305944] Chip ID: 0x0b [ 42.308669] Eco version: 0x01 [ 42.311751] Region number: 0x07 [ 42.314985] Format version: 0x02 [ 42.318354] Format flag: 0x01 [ 42.321428] Ram version: ____000000 [ 42.325070] Built date: 20201105222304 [ 42.328982] Common crc: 0xaa870ac [ 42.332390] Parsing tailer region 0 [ 42.335946] Decomp crc: 0x0 [ 42.338820] Decomp size: 0x0 [ 42.341810] Decomp block size: 0x0 [ 42.345304] Target address: 0x21fc00 [ 42.348969] Download size: 110592 [ 42.352370] Feature set: 0x20 [ 42.355440] Parsing tailer region 1 [ 42.358921] Decomp crc: 0x0 [ 42.361805] Decomp size: 0x0 [ 42.364773] Decomp block size: 0x0 [ 42.368266] Target address: 0x31dc00 [ 42.371930] Download size: 205824 [ 42.375323] Feature set: 0x00 [ 42.378400] Parsing tailer region 2 [ 42.381896] Decomp crc: 0x0 [ 42.384776] Decomp size: 0x0 [ 42.387748] Decomp block size: 0x0 [ 42.391249] Target address: 0x417400 [ 42.394918] Download size: 31744 [ 42.398234] Feature set: 0x00 [ 42.401305] Parsing tailer region 3 [ 42.404799] Decomp crc: 0x0 [ 42.407680] Decomp size: 0x0 [ 42.410639] Decomp block size: 0x0 [ 42.414133] Target address: 0xe0022800 [ 42.417969] Download size: 411136 [ 42.421375] Feature set: 0x00 [ 42.424452] Parsing tailer region 4 [ 42.427946] Decomp crc: 0x0 [ 42.430818] Decomp size: 0x0 [ 42.433789] Decomp block size: 0x0 [ 42.437333] Target address: 0xe0086e00 [ 42.441173] Download size: 332288 [ 42.444596] Feature set: 0x00 [ 42.447667] Parsing tailer region 5 [ 42.451146] Decomp crc: 0x0 [ 42.454031] Decomp size: 0x0 [ 42.456998] Decomp block size: 0x0 [ 42.460490] Target address: 0x23ac00 [ 42.464150] Download size: 87040 [ 42.467468] Feature set: 0x00 [ 42.470530] Parsing tailer region 6 [ 42.474025] Decomp crc: 0x0 [ 42.476913] Decomp size: 0x0 [ 42.479884] Decomp block size: 0x0 [ 42.483363] Target address: 0x400000 [ 42.487029] Download size: 81920 [ 42.490342] Feature set: 0x00 [ 42.493415] Release info: header tag = 0, total length = 68 [ 42.499085] tag 1, padding length = 3, tag length = 61 [ 42.504313] payload: t-neptune-main-mt7915-1953-MT7915D_1953_MT7621-20201105221902 [ 42.512269] Start address = 0x21fc00, DL length = 110592, Data mode = 0x80000000 [ 42.520873] EventGenericEventHandler: CMD Success [ 42.525621] MtCmdAddressLenReq:(ret = 0) [ 42.529994] Start address = 0x31dc00, DL length = 205824, Data mode = 0x80000000 [ 42.538762] EventGenericEventHandler: CMD Success [ 42.543471] MtCmdAddressLenReq:(ret = 0) [ 42.548208] Start address = 0x417400, DL length = 31744, Data mode = 0x80000000 [ 42.556711] EventGenericEventHandler: CMD Success [ 42.561416] MtCmdAddressLenReq:(ret = 0) [ 42.565471] Start address = 0xe0022800, DL length = 411136, Data mode = 0x80000000 [ 42.574233] EventGenericEventHandler: CMD Success [ 42.578990] MtCmdAddressLenReq:(ret = 0) [ 42.584523] Start address = 0xe0086e00, DL length = 332288, Data mode = 0x80000000 [ 42.593314] EventGenericEventHandler: CMD Success [ 42.598104] MtCmdAddressLenReq:(ret = 0) [ 42.603308] Start address = 0x23ac00, DL length = 87040, Data mode = 0x80000000 [ 42.611821] EventGenericEventHandler: CMD Success [ 42.616560] MtCmdAddressLenReq:(ret = 0) [ 42.620849] Start address = 0x400000, DL length = 81920, Data mode = 0x80000000 [ 42.629366] EventGenericEventHandler: CMD Success [ 42.634098] MtCmdAddressLenReq:(ret = 0) [ 42.638418] MtCmdFwStartReq: override = 0x1, address = 0x21fc00 [ 42.645528] EventGenericEventHandler: CMD Success [ 42.650314] Parsing CPU 1 fw tailer [ 42.653810] Chip ID: 0x00 [ 42.656548] Eco version: 0x01 [ 42.659633] Region number: 0x03 [ 42.662866] Format version: 0x02 [ 42.666204] Format flag: 0x01 [ 42.669282] Ram version: DEV_000000 [ 42.672913] Built date: 20201105222323 [ 42.676843] Common crc: 0x8fcbc5ad [ 42.680339] Parsing tailer region 0 [ 42.683827] Decomp crc: 0x0 [ 42.686700] Decomp size: 0x0 [ 42.689673] Decomp block size: 0x0 [ 42.693161] Target address: 0x10200000 [ 42.697000] Download size: 88512 [ 42.700313] Feature set: 0x00 [ 42.703372] Parsing tailer region 1 [ 42.706866] Decomp crc: 0x0 [ 42.709747] Decomp size: 0x0 [ 42.712718] Decomp block size: 0x0 [ 42.716206] Target address: 0x10300000 [ 42.720046] Download size: 19392 [ 42.723352] Feature set: 0x00 [ 42.726422] Parsing tailer region 2 [ 42.729925] Decomp crc: 0x0 [ 42.732804] Decomp size: 0x0 [ 42.735831] Decomp block size: 0x0 [ 42.739311] Target address: 0xe0000000 [ 42.743154] Download size: 8768 [ 42.746383] Feature set: 0x00 [ 42.749458] Release info: header tag = 0, total length = 0 [ 42.755041] Start address = 0x10200000, DL length = 88512, Data mode = 0x80000010 [ 42.763727] EventGenericEventHandler: CMD Success [ 42.768466] MtCmdAddressLenReq:(ret = 0) [ 42.773014] Start address = 0x10300000, DL length = 19392, Data mode = 0x80000010 [ 42.781717] EventGenericEventHandler: CMD Success [ 42.786460] MtCmdAddressLenReq:(ret = 0) [ 42.790498] Start address = 0xe0000000, DL length = 8768, Data mode = 0x80000010 [ 42.799121] EventGenericEventHandler: CMD Success [ 42.803848] MtCmdAddressLenReq:(ret = 0) [ 42.807834] MtCmdFwStartReq: override = 0x4, address = 0x0 [ 42.913118] EventGenericEventHandler: CMD Success [ 42.917856] :MtCmdCr4Capability: option(0) [ 42.921988] MCU Init Done! [ 42.924715] efuse_probe: efuse = 10000012 [ 42.928731] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 42.934134] RtmpEepromGetDefault::e2p_dafault=1 [ 42.938669] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 42.946250] NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x5000] [ 42.952268] rtmp_nv_init(): EEPROM Size[131072] [ 42.958049] [EEPROMImage - PreCalImageInfo - PreCalImage - TxDPDImage] [ 42.958049] [0xffffffc00f9a0000 - 0xffffffc00f9a0e00 - 0xffffffc00f9a0e10 - 0xffffffc00f9ad220] [ 42.974801] validFlashEepromID(): eeFlashId=7915, pAd->ChipID=7915 [ 42.980994] NICReadEEPROMParameters: EEPROM 0x62 0 [ 48.217664] Country Region from e2p = 0 [ 48.221545] antenna_default_reset() todo [ 48.225476] antenna_default_reset() value = 0x2424, TxPath = 4, RxPath = 4 [ 48.232388] RTMPReadTxPwrPerRate(458): Don't Support this now! [ 48.238233] rc_radio_init(): DBDC MODE=0, ConcurrentBand=1 [ 48.243847] rc_radio_init(): radio_ctrl=ffffffc012af1ee8,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf [ 48.253185] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 48.258938] AntCfgInit(3415): Not support for HIF_MT yet! [ 48.264357] mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 48.269930] MtReadPwrLimitTable: sku table idx: 1 mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 48.281676] mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 48.287255] MtReadPwrLimitTable: sku table idx: 1 mt7915_check_RF_lock_down: RFlockDown Enable: 0 [ 48.299102] EEPROM Init Done! [ 48.302097] mac_init()--> [ 48.304724] init_mac_cr()--> [ 48.307611] <--mac_init() [ 48.313337] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 48.321642] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 48.329976] CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 [ 48.336558] MAC Init Done! [ 48.339259] BBPInit():BBP Initialization..... [ 48.343711] Band 0: valid=1, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 [ 48.351918] Band 1: valid=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 [ 48.360099] BBPInit() todo [ 48.362798] PHY Init Done! [ 48.371819] tx_pwr_comp_init():NotSupportYet! [ 48.376375] MtCmdSetMacTxRx:(ret = 0) [ 48.380329] ap_ftkd> Initialize FT KDP Module... [ 48.385026] Main bssid = 00:00:00:00:00:00 [ 48.389147] SetMuruPlatformTypeProc: param.ucPlatformType = 2 [ 48.394933] muru_cfg_dlul_limits:(Ret = 1 [ 48.398956] muru_cfg_dlul_limits:(Ret = 1 [ 48.403205] MtCmdSetMacTxRx:(ret = 0) [ 48.406882] <==== mt_wifi_init, Status=0 [ 48.410812] TxBfModuleEnCtrl:It's not DBDC mode [ 48.415373] CmdHeraStbcPriorityCtrl: u1BandIdx=0, u1Operation=1, u1StbcPriority=0 [ 48.422876] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.428628] [set_datcfg_ack_cts_timeout](10924): DAT config band(0) cck_timeout Fail! [ 48.436543] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.442293] [set_datcfg_ack_cts_timeout](10935): DAT config band(0) ofdm_timeout Fail! [ 48.450228] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.455977] [set_datcfg_ack_cts_timeout](10946): DAT config band(0) ofdma_timeout Fail! [ 48.463978] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.469728] [set_datcfg_ack_cts_timeout](10924): DAT config band(1) cck_timeout Fail! [ 48.477556] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.483304] [set_datcfg_ack_cts_timeout](10935): DAT config band(1) ofdm_timeout Fail! [ 48.491227] CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 48.496976] [set_datcfg_ack_cts_timeout](10946): DAT config band(1) ofdma_timeout Fail! [ 48.505016] Register MBSSID IF 1 (rai1) [ 48.510716] wdev_init(caller:mbss_create_vif+0x2bc/0x4b0 [mt7915_mt_wifi_ap]), wdev(1) [ 48.519182] MSTA_Init (1) ---> ApCli [ 48.522848] Register MSTA IF (apclii0) , pAd->MSTANum = 1 [ 48.530116] wdev_init(caller:MSTA_Init+0x344/0x590 [mt7915_mt_wifi_ap]), wdev(2) [ 48.539809] Caller: dump_ht_cap+0x10/0x20 [mt7915_mt_wifi_ap] [ 48.545599] [ 48.545599] phy_mode=177, ch=0, wdev_type=2 [ 48.551264] ht_cap: ht_cap->HtCapInfo, [ 48.555104] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 48.562762] ht_cap: ht_cap->HtCapParm, [ 48.566594] mdpu_density=0, ampdu_factor=3 [ 48.571223] mt_service_init: wlan service inits successfully! [ 48.576989] WtcSetMaxStaNum: MaxStaNum:236, BssidNum:2, WdsNum:16, MSTANum:1, MaxNumChipRept:32, MinMcastWcid:285 [ 48.704140] RedInit: set CR4/N9 RED Enable to 1. [ 48.708766] RedInit: RED Initiailize Done. [ 48.713044] cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 3. [ 48.719056] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 48.725337] wifi_sys_open(), wdev idx = 0 [ 48.729359] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 48.735127] BuildChannelList() BandIdx = 0, PhyMode = 177, ChListNum = 4: [ 48.742025] DfsBuildChannelList(): Done [ 48.745875] phy_oper_init(): operate TxStream = 4, RxStream = 4 [ 48.751813] [RadarStateCheck] RD_NORMAL_MODE [ 48.757216] phy_freq_adjust : no prim_ch value for adjust! [ 48.764580] Caller: wlan_operate_init+0xf8/0x130 [mt7915_mt_wifi_ap] [ 48.770988] [ 48.770988] phy_mode=177, ch=0, wdev_type=1 [ 48.776685] ht_cap: ht_cap->HtCapInfo, [ 48.780524] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 48.788214] ht_cap: ht_cap->HtCapParm, [ 48.792053] mdpu_density=5, ampdu_factor=3 [ 48.796228] hw_ctrl_flow_v2_open: wdev_idx=0 [ 48.800698] AP inf up for ra_0(func_idx) OmacIdx=0 [ 48.805509] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 48.810550] BndStrg_Init() BndStrg_TableInit(),Invalid Channel:0 pMbss apidx:0 [ 48.818834] Error in BndStrg_Init(), error code = 9 on apidx = 0 [ 48.824849] BndStrg_TableInit(),Invalid Channel:0 pMbss apidx:1 [ 48.830769] Error in BndStrg_Init(), error code = 9 on apidx = 1 [ 48.836822] ApAutoChannelAtBootUp-----------------> [ 48.841779] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 [ 48.847535] MtCmdSetMacTxRx:(ret = 0) [ 48.851210] [AutoChSelBuildChannelListFor5G] ChListNum5G = 4 [ 48.858860] UpdateBeaconHandler, wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x198/0x420 [mt7915_mt_wifi_ap])!! [ 49.737563] UpdateBeaconHandler, wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x338/0x420 [mt7915_mt_wifi_ap])!! [ 49.749251] ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 40, IsAband = 1 [ 49.757875] [RadarStateCheck] RD_NORMAL_MODE [ 49.981250] DfsBuildChannelList(): Done [ 49.985138] zero_wait_dfs_switch_ch(): outband ch 0, ch_stat 0 [ 49.990981] ApAutoChannelAtBootUp<----------------- [ 49.997708] ===> APStartUpForMbss(caller:ap_inf_open+0x138/0x1c0 [mt7915_mt_wifi_ap]), mbss_idx:0, CfgMode:177 [ 50.007781] [PMF]APPMFInit:: apidx=0, MFPC=1, MFPR=0, SHA256=0 [ 50.013629] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE [ 50.024197] Caller: dump_ht_cap+0x10/0x20 [mt7915_mt_wifi_ap] [ 50.030031] [ 50.030031] phy_mode=177, ch=40, wdev_type=1 [ 50.035782] ht_cap: ht_cap->HtCapInfo, [ 50.039622] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 50.047280] ht_cap: ht_cap->HtCapParm, [ 50.051114] mdpu_density=5, ampdu_factor=3 [ 50.055223] Enable 20/40 BSSCoex Channel Scan(BssCoex=1) [ 50.062432] ap_link_up(caller:wdev_do_linkup+0x1c/0x30 [mt7915_mt_wifi_ap]), wdev(0) [ 50.070533] wifi_sys_linkup, wdev idx = 0 [ 50.144136] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 [ 50.144136] LinkToOmacIdx = 0, LinkToWdevType = 1 [ 50.157006] TRTableInsertMcastEntry:band0 group_idx[0]=0 [ 50.162333] wifi_sys_linkup:wdev(type=0,func_idx=1,wdev_idx=0),BssIndex(0) [ 50.169236] hw_ctrl_flow_v2_link_up: wdev_idx=0 [ 50.173968] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 50.185112] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 [ 50.201345] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (rai0) [ 50.207705] Band0 BcnInitedRnd = 15 [ 50.211291] MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0 [ 50.217064] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 1, BandIdx: 0 [ 50.223092] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 [ 50.229661] TxCCKStreamCtrl: set wrong parameters [ 50.241881] BndStrg_SetInfFlags(): BSS(<< WLAN1_MAC >>) set 5G Inf rai0 ready. set muru_update_he_cfg()!!!! [ 50.253934] PrintSrCmd: [ 50.253934] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 50.253934] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 50.267995] PrintSrCmd: [ 50.267995] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 50.267995] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 50.282031] PrintSrCmd: [ 50.282031] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 50.282031] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 50.296076] PrintSrCmd: [ 50.296076] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 50.296076] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 50.310216] MtCmdTxPwrShowInfo: ucTxPowerInfoCatg: 2, BandIdx: 0 [ 50.316328] apidx 0 for WscUUIDInit [ 50.316457] [mtf_txpower_all_rate_info] band_idx:0 pwr:18 ChBand:5G ePAGain:0 [ 50.326951] Generate UUID for apidx(0) [ 50.330741] WDS_Init():wds_num[0]=0, count=0, MAX_WDS_ENTRY=16, if_idx=0, flg_wds_init=0 [ 50.338835] Total allocated 0 WDS(es) for band0! [ 50.343545] mtk_ppe_dev_register_hook : ineterface rai0 register (2) [ 51.355356] device rai0 entered promiscuous mode [ 51.360036] br0: port 3(rai0) entered forwarding state [ 51.365194] br0: port 3(rai0) entered forwarding state [ 51.392053] rai1: ===> mbss_virtual_if_open Set multicast_to[ 51.396406] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT _unicast kernel [ 51.404503] RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP option to 1 on i[ 51.411849] wifi_sys_open(), wdev idx = 1 [ 51.417385] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 [ 51.424356] phy_oper_init(): operate TxStream = 4, RxStream = 4 [ 51.432376] Caller: wlan_operate_init+0xf8/0x130 [mt7915_mt_wifi_ap] [ 51.438835] [ 51.438835] phy_mode=177, ch=40, wdev_type=1 [ 51.445098] ht_cap: ht_cap->HtCapInfo, [ 51.448963] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 51.456820] ht_cap: ht_cap->HtCapParm, [ 51.460660] mdpu_density=0, ampdu_factor=3 [ 51.464965] hw_ctrl_flow_v2_open: wdev_idx=1 [ 51.469384] AP inf up for ra_1(func_idx) OmacIdx=17 [ 51.474411] AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn [ 51.479552] BndStrg_Init() ApAutoChannelAtBootUp-----------------> [ 51.486828] ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 [ 51.492821] MtCmdSetMacTxRx:(ret = 0) [ 51.496518] ap_run_at_boot() : ACS is disable !! [ 51.503946] ===> APStartUpForMbss(caller:ap_inf_open+0x138/0x1c0 [mt7915_mt_wifi_ap]), mbss_idx:1, CfgMode:177 [ 51.514035] [PMF]APPMFInit:: apidx=1, MFPC=1, MFPR=0, SHA256=0 [ 51.584773] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE [ 51.595268] Caller: dump_ht_cap+0x10/0x20 [mt7915_mt_wifi_ap] [ 51.601467] [ 51.601467] phy_mode=177, ch=40, wdev_type=1 [ 51.607250] ht_cap: ht_cap->HtCapInfo, [ 51.611097] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 [ 51.619018] ht_cap: ht_cap->HtCapParm, [ 51.622862] mdpu_density=0, ampdu_factor=3 [ 51.627104] Enable 20/40 BSSCoex Channel Scan(BssCoex=1) [ 51.634389] ap_link_up(caller:wdev_do_linkup+0x1c/0x30 [mt7915_mt_wifi_ap]), wdev(1) [ 51.642174] wifi_sys_linkup, wdev idx = 1 [ 51.716122] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 [ 51.716122] LinkToOmacIdx = 11, LinkToWdevType = 1 [ 51.729123] TRTableInsertMcastEntry:band0 group_idx[1]=1 [ 51.734457] wifi_sys_linkup:wdev(type=1,func_idx=1,wdev_idx=1),BssIndex(1) [ 51.741650] hw_ctrl_flow_v2_link_up: wdev_idx=1 [ 51.746376] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 51.757514] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8192 [ 51.774535] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (rai0) [ 51.781002] MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0 [ 51.786996] MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 1, BandIdx: 0 [ 51.793117] MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 [ 51.799941] TxCCKStreamCtrl: set wrong parameters [ 51.812147] BndStrg_SetInfFlags(): BSS(06:BA:D6:50:D0:04) set 5G Inf rai1 ready. set muru_update_he_cfg()!!!! [ 51.824097] PrintSrCmd: [ 51.824097] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 51.824097] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 51.838546] PrintSrCmd: [ 51.838546] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 51.838546] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 51.852651] PrintSrCmd: [ 51.852651] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 51.852651] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 51.867125] PrintSrCmd: [ 51.867125] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 51.867125] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 51.881272] MtCmdTxPwrShowInfo: ucTxPowerInfoCatg: 2, BandIdx: 0 [ 51.887707] apidx 1 for WscUUIDInit [ 51.887829] [mtf_txpower_all_rate_info] band_idx:0 pwr:18 ChBand:5G ePAGain:0 [ 51.898352] Generate UUID for apidx(1) [ 51.902427] mtk_ppe_dev_register_hook : ineterface rai1 register (3) Set multicast_to_unicast kernel option to 1 on interface ra0 Set multicast_to_unicast kernel option to 1 on interface rai0 [ 52.914178] device rai1 entered promiscuous mode [ 52.918876] br0: port 4(rai1) entered forwarding state [ 52.924038] br0: port 4(rai1) entered forwarding state Set multicast_to_unicast kernel option to 1 on interface eth0.1 Set multicast_to_unicast kernel option to 1 on interface ra0 Set multicast_to_unicast kernel option to 1 on interface rai0 rai0 Channel Value: 40 Set multicast_to_unicast kernel option to 1 on interface rai1 nf_handle_macctl_wlanap 2522 iwpriv ra0 set AccessPolicy=0 nf_handle_macctl_wlanap 2539 iwpriv rai0 set AccessPolicy=0 nf_handle_macctl_wlanap 2539 iwpriv rai1 set AccessPolicy=0 Run emdaemons after wifi done optind:1 argc:2 get_device_info... [ 55.396825] Current mapfilter version v2.0.2 [ 55.405974] Set_Map_Proc current MAP MODE is 1 [ 55.415097] Set_Map_Proc current MAP MODE is 1 [process_options]Default interface: ra0 [disable_dhcp_client]TODO: disable dhcp client!!!!!!!!!!! [main]Map cfg file: /etc/map/mapd_cfg Map user cfg: /etc/map/mapd_user.cfg [main]WAPP version: v2.0.0 wapp cmm type version: v2.0.0 [main]Initialize socket [driver_wext_init]Initialize ralink wext interface [main]Initialize IAPP ===== WAPP DAEMON VER:v2.0.0 ===== [driver_wext_wapp_support_version] driver_support_wapp_ver=[v2.0.2] [driver_wext_wapp_support_version]driver support WAPP ver (v2.0.2) < cur WAPP ver (v2.0.0) ===== WAPP DAEMON VER:v2.0.0 ===== [driver_wext_wapp_support_version] driver_support_wapp_ver=[v2.0.2] [driver_wext_wapp_support_version]driver support WAPP ver (v2.0.2) < cur WAPP ver (v2.0.0) ===== WAPP DAEMON VER:v2.0.0 ===== [driver_wext_wapp_support_version] driver_support_wapp_ver=[v2.0.2] [driver_wext_wapp_support_version]driver support WAPP ver (v2.0.2) < cur WAPP ver (v2.0.0) ===== WAPP DAEMON VER:v2.0.0 ===== [driver_wext_wapp_support_version] driver_support_wapp_ver=[v2.0.2] [driver_wext_wapp_support_version]driver support WAPP ver (v2.0.2) < cur WAPP ver (v2.0.0) [get_map_parameters]get param(Enable_WPS_toggle_5GL_5GH) fail [get_map_parameters]get param(MaxStaAllowed) fail get_if_info for br0 interface index is 10 get_if_info OK Clean up temporary socket bind_arp: ifindex=10 Binding to ifindex 10 bind_arp: ifindex=11 Binding to ifindex 11 bind_arp: ifindex=12 Binding to ifindex 12 [mt_iapp_get_wifi_iface_mac]iapp> mt_iapp_get_wifi_iface_mac - IfName[0]: ra0 MAC: 0x7ffd930c78, len = 6 0x0000 : 04 ba d6 50 d0 03 [mt_iapp_get_wifi_iface_mac]iapp> mt_iapp_get_wifi_iface_mac - IfName[1]: rai0 MAC: 0x7ffd930c7e, len = 6 0x0000 : 04 ba d6 50 d0 04 [mt_iapp_get_wifi_iface_mac]iapp> mt_iapp_get_wifi_iface_mac - IfName[2]: rai1 MAC: 0x7ffd930c84, len = 6 0x0000 : 06 ba d6 50 d0 04 bind_arp: ifindex=19 Binding to ifindex 19 bind_arp: ifindex=20 Binding to ifindex 20 [wapp_init_ap_config]typelen=9, filelen=16 [wapp_set_interworking_enable]wapp_set_interworking_enable [ 55.714021] Enable GAS service for MBSSID[0] [driver_wext_get[ 55.718847] Enable GAS service for MBSSID[0] _oid]driver_wext[ 55.724169] Unknow Parameter:8 _get_oid: oid=0x[ 55.728746] Unknow Parameter:0 941 len (6) fail[ 55.733118] Unknow Parameter:1 ed [hotspot_get[ 55.737523] Unknow Parameter:2 _bssid]hessid_le[ 55.741905] Unknow Parameter:3 n is not six [w[ 55.746358] Set_AP_VENDOR_SPECIFIC_IE: Unknown OUIType = 16 app_set_interwor[ 55.753352] Set_AP_VENDOR_SPECIFIC_IE: Unknown OUIType = 9 king_enable]wapp[ 55.760143] set_wapp_cmm_ie: Unknown IE(EID = 111) _set_interworkin[ 55.766331] set_wapp_cmm_ie: Unknown IE(EID = 110) g_enable [ 55.772565] Set_HotSpot_OnOff ==> wdev[0] is already in [OFF] STATE , skip. [hotspot_onoff]Disable hotspot2.0 feature(ra0) [driver_wext_get[ 55.784788] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x0 _oid]driver_wext_get_oid: oid=0x93e len (8) failed [hotspot_ono[ 55.795742] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 ff]Disable hotspot2.0 feature(rai0) [driver_wext_set_oid]driver_wext_set_oid: oid=0x925 len (8) failed wdev_qu[ 55.811985] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x0 ery_rsp_handle: dev_type = 1, mac = << WLAN0_MAC >>, ifname = [ 55.822476] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 ra0 (156241920) aquired a new card id 1 [wapp_reset_backhaul_config]wapp_reset_backhaul_config misc_cap (11): m[ 55.839057] Set_Fh_Bss_Proc rai1 wdev->MAPCfg.DevOwnRole 0x40 ax_num_of_cli = 64 max_num_of_bss = 16 [ 55.850963] Set_Fh_Bss_Proc rai1 wdev->MAPCfg.DevOwnRole 0x60 max_num_of_block_cli = 128 ht_cap (11): tx_stream = 4, rx_stream = 4, sgi_20 = 1, sgi_40 = 1, ht_40 = 0 vht_cap (11): sup_tx_mcs[]= aa ff sup_rx_mcs[] = 170 255 tx_stream = 4, rx_stream = 4 sgi_80 = 1, sgi_160 = 1 vht160 = 0, vht8080 = 0 su_bf = 0, mu_bf = 0 [driver_wext_get_oid]driver_wext_get_oid: oid=0x99d len (24) failed he_cap (11): tx_stream = 0, rx_stream = 0, he_160 = 0, he_8080 = 0, he_mcs_len = 0 chn_list: (11) op_class = 83 op_ch = 1 band = 14 ch_list_num = 13 non_op_chn_num = 0 dl_mcs = 31 op_class: (11) num_of_op_class = 3 opClass = 81, chn_num = 13 opClass = 83, chn_num = 9 opClass = 84, chn_num = 9 bss_info: (11) table idx = 0 ssid = M32-D002 SsidLen = 8 map role = 32 Bssid = [04][ba][d6][50][d0][03] Identifier = [04][ba][d6][50][d0][03] [driver_wext_get_oid]driver_wext_get_oid: oid=0x68a len (4) failed [driver_wnm_btm_onoff]driver_wnm_btm_onoff [driver_wnm_btm_onoff]driver_wnm_btm_onoff: cmd->command_body[0] = 1 [driver_rrm_onoff]driver_rrm_onoff wdev_query_rsp_handle: dev_type = 1, mac = << WLAN1_MAC >>, ifname = rai0 (177213440) aquired a new card id 2 [wapp_reset_backhaul_config]wapp_reset_backhaul_config misc_cap (12): max_num_of_cli = 64 max_num_of_bss = 32 num_of_bss = 2 max_num_of_block_cli = 128 ht_cap (12): tx_stream = 4, rx_stream = 4, sgi_20 = 1, sgi_40 = 1, ht_40 = 1 vht_cap (12): sup_tx_mcs[]= aa ff sup_rx_mcs[] = 170 255 tx_stream = 4, rx_stream = 4 sgi_80 = 1, sgi_160 = 1 vht160 = 0, vht8080 = 0 su_bf = 1, mu_bf = 1 he_cap (12): tx_stream = 4, rx_stream = 4, he_160 = 0, he_8080 = 0, he_mcs_len = 2 chn_list: (12) op_class = 129 op_ch = 40 band = 177 ch_list_num = 4 non_op_chn_num = 2 dl_mcs = 9 op_class: (12) num_of_op_class = 6 opClass = 115, chn_num = 4 opClass = 116, chn_num = 2 opClass = 117, chn_num = 2 opClass = 128, chn_num = 1 opClass = 129, chn_num = 1 opClass = 130, chn_num = 1 bss_info: (12) table idx = 1 ssid = M32-D002 SsidLen = 8 map role = 32 Bssid = [04][ba][d6][50][d0][04] Identifier = [04][ba][d6][50][d0][04] [driver_wnm_btm_onoff]driver_wnm_btm_onoff [driver_wnm_btm_onoff]driver_wnm_btm_onoff: cmd->command_body[0] = 1 [driver_rrm_onoff]driver_rrm_onoff wdev_query_rsp_handle: dev_type = 1, mac = 06:ba:d6:50:d0:04, ifname = rai1 [wapp_reset_backhaul_config]wapp_reset_backhaul_config misc_cap (19): max_num_of_cli = 64 max_num_of_bss = 32 num_of_bss = 2 max_num_of_block_cli = 128 ht_cap (19): tx_stream = 4, rx_stream = 4, sgi_20 = 1, sgi_40 = 1, ht_40 = 1 vht_cap (19): sup_tx_mcs[]= aa ff sup_rx_mcs[] = 170 255 tx_stream = 4, rx_stream = 4 sgi_80 = 1, sgi_160 = 1 vht160 = 0, vht8080 = 0 su_bf = 1, mu_bf = 1 he_cap (19): tx_stream = 4, rx_stream = 4, he_160 = 0, he_8080 = 0, he_mcs_len = 2 chn_list: (19) op_class = 129 op_ch = 40 band = 177 ch_list_num = 4 non_op_chn_num = 2 dl_mcs = 9 op_class: (19) num_of_op_class = 6 opClass = 115, chn_num = 4 opClass = 116, chn_num = 2 opClass = 117, chn_num = 2 opClass = 128, chn_num = 1 opClass = 129, chn_num = 1 opClass = 130, chn_num = 1 bss_info: (19) table idx = 2 ssid = M32-backhaul-D002 SsidLen = 17 map role = 96 Bssid = [06][ba][d6][50][d0][04] Identifier = [06][ba][d6][50][d0][04] [driver_wnm_btm_onoff]driver_wnm_btm_onoff [driver_wnm_btm_onoff]driver_wnm_btm_onoff: cmd->command_body[0] = 1 [driver_rrm_onoff]driver_rrm_onoff [ 56.615478] do_map_set_ctl==>cmd(1905) [ 56.619232] do_map_set_ctl==>almac(<< LAN_MAC >>) [ 56.637990] handle_map_command Traffic Seperation(0) [ 56.642987] handle_map_command Traffic Seperation(1) [ 56.648198] handle_ts_default_8021q vid=4095, pcp=0 [ 56.653093] ts policy number=0 daemon mapd attached \x00/tmp/wa[ 58.577286] do_map_set_ctl==>cmd(1905) pp_ctrl [WAPP]m[ 58.581306] do_map_set_ctl==>almac(<< WLAN0_MAC >>) ap_send_wirelss_inf_info send info ra0, role: wiap, dev type = 1 MAC Address = << WLAN0_MAC >> send info rai0, role: wiap, dev type = 1 MAC Address = << WLAN1_MAC >> send info rai1, role: wiap, dev type = 1 MAC Address = 06:ba:d6:50:d0:04 get_device_info... contents to file written successfully ! ctrler_found [WAPP]map_send_wirelss_inf_info send info ra0, role: wiap, dev type = 1 MAC Address = << WLAN0_MAC >> send info rai0, role: wiap, dev type = 1 MAC Address = << WLAN1_MAC >> send info rai1, role: wiap, dev type = 1 MAC Address = 06:ba:d6:50:d0:04 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 0 1 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4375: 2G [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 1 40 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 2 0 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 3 0 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 4 0 [mapd_get_channel_scan_capab_from_driver]mapd_get_channel_scan_capab_from_driver 4367 5 0 ScanCapab: 0x2ed6d810, len = 310 0x0000 : 02 00 00 00 00 01 00 00 03 3c 00 00 00 02 51 00 0x0010 : 00 00 00 00 00 00 00 00 00 00 00 00 00 52 00 00 0x0020 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0030 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0040 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0050 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0060 : 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00 03 0x0070 : 3c 00 00 00 04 73 00 00 00 00 00 00 00 00 00 00 0x0080 : 00 00 00 00 76 00 00 00 00 00 00 00 00 00 00 00 0x0090 : 00 00 00 79 00 00 00 00 00 00 00 00 00 00 00 00 0x00a0 : 00 00 7d 00 00 00 00 00 00 00 00 00 00 00 00 00 0x00b0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x00c0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x00d0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x00e0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x00f0 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0100 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0110 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0120 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0130 : 00 00 00 00 00 00 in WAPP driver_cap->cac_mode 0in WAPP driver_cap->cac_mode 0[map_build_cac_cap]map_build_cac_cap 2820 [map_build_cac_cap] ptr 28, map_event->length-28[map_build_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_info [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability_msg]map_send_metric_reporting_capability_msg [map_build_metric_reporting_info]map_build_metric_reporting_info [map_build_metric_reporting_info]map_build_metric_reporting_info 60 [wapp_read_wts_map_config]set bss index=1, mac=ff:ff:ff:ff:ff:ff, opclass=8x, ssid=TTMyLUQwMDI=, authmode=0020, encrytype=0008, key=tuvfv84986, bh_bss=0, fh_bss=1 hidden_ssid=0 [wapp_read_wts_map_config]set bss index=2, mac=ff:ff:ff:ff:ff:ff, opclass=11x, ssid=TTMyLUQwMDI=, authmode=0020, encrytype=0008, key=tuvfv84986, bh_bss=0, fh_bss=1 hidden_ssid=0 [wapp_read_wts_map_config]set bss index=3, mac=ff:ff:ff:ff:ff:ff, opclass=11x, ssid=TTMyLWJhY2toYXVsLUQwMDI=, authmode=0060, encrytype=0008, key=xejkd67379, bh_bss=1, fh_bss=0 hidden_ssid=1 [wapp_read_wts_map_config]config_bss_num=3 [map_build_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_info [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability_msg]map_send_metric_reporting_capability_msg [map_build_metric_reporting_info]map_build_metric_reporting_info [map_build_metric_reporting_info]map_build_metric_reporting_info 60 [map_build_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_info map_build_ap_he_cap: - Unknow HE Tx Spatial Stream!! map_build_ap_he_cap: - Unknow HE Rx Spatial Stream!! [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability_msg]map_send_metric_reporting_[ 59.925666] handle_map_command Dynamic Load Balance(0) capability_msg [ 59.932734] mapfilter: Stop drop the specific ip packets now !! [map_build_metric_reporting_info]map_build_metric_reporting_info [ 59.944979] Set_Bh_Bss_Proc ra0 bandIdx = 0 ,DevOwnRole 0x20 [map_build_met[ 59.951094] ----->free map device rcu ffffffc010707990 ric_reporting_in[ 59.951096] ----->free map device rcu ffffffc010707d10 fo]map_build_met[ 59.951097] ----->free map device rcu ffffffc010707890 ric_reporting_in[ 59.951099] ----->free map device rcu ffffffc010707710 fo 60 [map_buil[ 59.977398] mapfilter: Stop drop the specific ip packets now !! d_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_i nfo [vlan] vlan[ 59.990385] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 - v1.0.3 v1.25 map_build_ap_he_cap: - Unknow HE Tx Spatial Stream!! map_[ 60.004631] Set_Bh_Bss_Proc rai1 bandIdx = 0 ,DevOwnRole 0x20 build_ap_he_cap: - Unknow HE Rx Spatial Stream!! Created SM Eventloop successf[ 60.017007] Set_Fh_Bss_Proc rai1 wdev->MAPCfg.DevOwnRole 0x20 ully [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability[ 60.031355] Set_Bh_Bss_Proc rai1 bandIdx = 0 ,DevOwnRole 0x60 _msg]map_send_metric_reporting_capability_msg [map_build_metric[ 60.043184] Set_Bh_Bss_Proc rai0 bandIdx = 0 ,DevOwnRole 0x20 _reporting_info]map_build_metric_reporting_info [map_build_metric_reporting_info]map_build_metric_reporting_inf[ 60.058229] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 o 60 [vlan] vlan Start [vlan] triple play = 0 wdev_set_bss_role-[ra0] i_am_fh_bss 1 , i_am_bh_bss 0 [vlan] wanNum = 1, lanNum = 2, virturalwanNum = 0 [vlan] wanIndex = 0, lanIndex = 1, virtualwanIndex = 3 [vlan] wan port map: 0 [vlan] i = 0 position = 0 type = 1 portIndex = 0 portLogic = 0 portPhyId = 4 [vlan] i = 0 wanPosition = 0 wanIndex = 99 vwBindWanIndex = -1 [vlan] i = 0 wanMac = << WAN_MAC >> [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 wanInterface = eth0.2 [vlan] i = 0 portInterface = eth0 [vlan] lan port map: 1 2 -1 [vlan] i = 1 position = 1 type = 2 portIndex = 1 portLogic = 1 portPhyId = 3 [vlan] i = 1 lanIndex = 0 [[ 60.121247] [PMF]APPMFInit:: apidx=0, MFPC=1, MFPR=0, SHA256=0 vlan] i = 1 lanM[ 60.128680] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE ac = << MAC_BASE >>[ 60.138438] wifi_sys_linkdown(), wdev idx = 0 2 [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 lanInterface = [vlan] i = 2 position = 2 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 [vlan] i = 2 lanIndex = 1 [vlan] i = 2 lanMac = << LAN_MAC >> [vlan] i =[ 60.165605] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 2 portMac = 000000000000 [vlan] i = 2 portInterface = eth0 [vlan] i = 2 lanInterface = [vlan] i = 1 lanInterface = eth0.1 [vlan] i = 2 lanInterface = eth0.1 [vlan] Port Map 0011000 [vlan] Complete Cmd [vlan] Vlan Cmd Exit [vlan] vlan End [vlan] vlan - v1.0.3 [vlan] vlan Start wdev_set_bss_role-[rai1] i_am_fh_bss 1 , i_am_bh_bss 1 [vlan] triple play = 0 [vlan] wanNum = 1, lanNum = 2,[ 60.211115] wifi_sys_close(), wdev idx = 0 virturalwanNum = 0 [vlan] wanIndex = 0, lanInd[ 60.218876] wifi_sys_open(), wdev idx = 0 ex = 1, virtualw[ 60.224312] wdev_attr_update(): wdevId0 = << WLAN0_MAC >> anIndex = 3 [vl[ 60.231290] [RadarStateCheck] RD_NORMAL_MODE an] wan port map: 0 [vlan] i = [ 60.239353] Caller: wlan_operate_init+0xdc/0x118 [mt_wifi_ap] 0 position = 0 t[ 60.246634] phy_mode=14, ch=1, wdev_type=1 ype = 1 portInde[ 60.252069] ht_cap->HtCapInfo: ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0 x = 0 portLogic [ 60.262778] ht_cap->HtCapParm: mdpu_density=5, ampdu_factor=3 = 0 portPhyId = 4 [vlan] i = 0 wanPosition = 0 [ 60.272639] wifi_sys_linkup(), wdev idx = 0 wanIndex = 99 vw[ 60.278382] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 [ 60.278382] LinkToOmacIdx = 0, LinkToWdevType = 1 BindWanIndex = -1 [vlan] i = 0 wanMac = << WAN_MAC >> [vlan] i = 0 portMac = 000000000000 [vlan] i = 0 wanInterface = eth0.2 [vlan] i = 0 portInterface = eth0 [vlan] lan port map: 1 2 -1 [vlan] i = 1 position = 1 type = 2 portIndex = 1 portLogic = 1 portPhyId = 3 [vlan] i = 1 lanIndex = 0 [vlan] i = 1 lanMac = << LAN_MAC >> [vlan] i = 1 portMac = 000000000000 [vlan] i = 1 portInterface = eth0 [vlan] i = 1 lanInterface = [vlan] i = 2 position = 2 type = 2 portIndex = 2 portLogic = 2 portPhyId = 2 [vlan] i = 2 lanIndex = 1 [vlan] i = 2 lanMac = << LAN_MAC >> [ 60.341292] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 [vlan] i = 2 portMac = 000000000000 [vlan] i = 2 portInterface = eth0 [vlan] i = 2 lanInterface = [vlan] i = 1 lanInterface = eth0.1 [vlan] i = 2 lanInterface = eth0.1 [vlan] Port Map 0011000 [vlan] Complete Cmd [vlan] Vlan Cmd Exit [vlan] vlan End [MASTER_SM] Loading Configuration : Filename with path is /tmp/emDaemon/dlinkEmeshMQTTlogFile.txt wdev_set_bss_role-[rai0] i_am_fh_bss 1 , i_am_bh_bss 0 [map_acl_system_cmd]map_acl_system_cmd ACL type = 2 [map_acl_system_cmd]map_acl_system_cmd ACL type = 2 [map_acl_system_cmd]map_acl_system_cm[ 60.402356] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 d ACL type = 2 0 ssid=M32-D002, autmode=0x0020, encryptype=0x0008, key=tuvfv84986 bh_bss=0, fh_bss=1 [fill_sec[ 60.416667] Set_Bh_Bss_Proc ra0 bandIdx = 0 ,DevOwnRole 0x20 _info]fill_sec_info, kapil: auth = WPA2PSK len=7 [fill_sec_info[ 60.428276] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 ]fill_sec_info, encryptype(3) = AES set sec_info: ifname = ra0 auth = WPA2PSK encryp = AES passphrases = tuvfv84986 1-iwpriv ra0 set AuthMode=WPA2PSK; zsh:1: command not found: wifi_config_save [wdev_set_sec_and_ssid] [wdev_set_sec_and_ssid] Send AuthMode Command: wifi_config_save ra0 AuthMode WPA2PSK, ret = 32512 2-iwpriv ra0 set EncrypType=AES; zsh:1: command not found: wifi_config_save [wdev_set_sec_and_ssid] [wdev_set_sec_and_ssid] Send EncrypType Command: wifi_config_save ra0 EncrypType AES, ret = 32512 set psk: ifname = ra0 psk = tuvfv84986 [driver_wext_set_psk]driver_wext_set_psk : tuvfv84986 zsh:1: command not found: wifi_config_save [driver_wext_set_psk] [driver_wext_set_psk] Send WPAPSK Command: wifi_config_save ra0 WPAPSK "tuvfv84986"[ 60.501595] [PMF]APPMFInit:: apidx=0, MFPC=1, MFPR=0, SHA256=0 , ret = 32512 [[ 60.509052] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE driver_wext_set_ssid]driver_wext_set_ssid : M32-D002 M32-D002 [ 60.524025] wifi_sys_linkdown(), wdev idx = 0 zsh:1: command n[ 60.528853] ExtEventBeaconLostHandler::FW EVENT (<< WLAN1_MAC >>), Reason 0x10 ot found: wifi_c[ 60.537457] AP Beacon OFF!!! onfig_save [dri[ 60.542633] wifi_sys_linkdown:wdev(type=1,func_idx=0,wdev_idx=0),BssIndex(0) ver_wext_set_ssi[ 60.550437] hw_ctrl_flow_v2_link_down: wdev_idx=0 d] [driver_wext_set_ssid] Send SSID Command: wifi_config_save ra0 SSID "M32-D002", ret = 32512 wdev_set_bss_role-[ra0] i_am_fh_bss 1 , i_am_bh_bss 0 set ifname = ra0 hidessid = 0 zsh:1: command not foun[ 60.574310] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 d: wifi_config_s[ 60.586253] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 ave [wdev_set_hidden_ssid] [wde[ 60.600786] wifi_sys_close, wdev idx = 0 v_set_hidden_ssi[ 60.605459] hw_ctrl_flow_v2_close: wdev_idx=0 d] Send HideSSID[ 60.611365] wifi_sys_open(), wdev idx = 0 Command: wifi_c[ 60.616829] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 onfig_save ra0 H[ 60.623666] phy_oper_init(): operate TxStream = 4, RxStream = 4 ideSSID 0, ret = 32512 [map_con[ 60.633015] Caller: wlan_operate_init+0xf8/0x130 [mt7915_mt_wifi_ap] fig_wireless_set[ 60.640153] [ 60.640153] phy_mode=177, ch=40, wdev_type=1 ting_msg][ 60.647236] ht_cap: ht_cap->HtCapInfo, radio id=0000 ca[ 60.652435] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 rdid=0001 set MA[ 60.661564] ht_cap: ht_cap->HtCapParm, P_CONF_CONFED mdpu_density=5, ampdu_factor=3 [0m0 ssid=M32-D0[ 60.672276] hw_ctrl_flow_v2_open: wdev_idx=0 02, autmode=0x00[ 60.678331] wifi_sys_linkup, wdev idx = 0 20, encryptype=0x0008, key=tuvfv84986 bh_bss=0, fh_bss=1 1 ssid=M32-backhaul-D002, autmode=0x0060, encryptype=0x0008, key=xejkd67379 bh_bss=1, fh_bss=0 [fill_sec_info]fill_sec_info, kapil: auth = WPA2PSK len=7 [fill_sec_info]fill_sec_info, encryptype(3) = AES [driver_wext_get_oid]driver_wext_get_oid: oid=0x530 len (4) failed set sec_info: ifname = rai0 auth = WPA2PSK encryp = AES passphrases = tuvfv84986 1-iwpriv rai0 set AuthMode=WPA2PSK; handle_nat: nat restart Force to start schedule without consider the Time Sync status! zsh:1: command not found: wifi_config_save [wdev_set_sec_and_ssid] [wdev_set_sec_and_ssid] Send AuthMode Command: wifi_config_save rai0 AuthMode WPA2PSK, ret = 32512 2-iwpriv rai0 set EncrypType=AES; zsh:1: command not found: wifi_config_save [wdev_set_sec_and[ 60.753174] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 [ 60.753174] LinkToOmacIdx = 0, LinkToWdevType = 1 _ssid] [wdev_set[ 60.766932] TRTableInsertMcastEntry:band0 group_idx[0]=0 _sec_and_ssid] S[ 60.773604] wifi_sys_linkup:wdev(type=0,func_idx=1,wdev_idx=0),BssIndex(0) end EncrypType C[ 60.781828] hw_ctrl_flow_v2_link_up: wdev_idx=0 ommand: wifi_con[ 60.787907] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 fig_save rai0 En[ 60.800288] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 crypType AES, ret = 32512 set psk: ifname = rai0 psk = tu[ 60.817809] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (rai0) vfv84986 [drive[ 60.825722] bcn_buf_init():BcnPkt is allocated!, bcn offload=1 r_wext_set_psk]driver_wext_set_psk : tuvfv84986 ==NAT Stop wan999 ALL== NAT nat-draft stop rule start zsh:1: command not found: wifi_config_save [driver_wext_set_psk] [driver_wext_set_psk][ 60.848184] Set_Bh_Bss_Proc rai0 bandIdx = 0 ,DevOwnRole 0x20 Send WPAPSK Command: wifi_config_save rai0 WPAPSK "tuvfv84986", ret = 32512 [driver_wext_set_ssid]driver_wext_set_ssid : M32-D002 create dhcpd6.leases xxxxxxxxxxxxxxxx 60.869631] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 ;33m[V] [start][1637]WirelessRouter Mode [RNRCoordinator] Exist f8:e4:3b:70:a8:18 [RNRCoordinator] use = 1 1650615133: mosquitto version 1.6.8 starting 1650615133: Config loaded from /etc/emDaemon/mosquitto.conf. 1650615133: Opening ipv4 listen socket on port 1883. 1650615133: Opening ipv6 listen socket on port 1883. 1650615133: Warning: Mosquitto should not be run as root/administrator. zsh:1: command not found: wifi_config_save [driver_wext_set_ssid] [driver_wext_set_ssid] Send SSID Command: wifi_config_save rai0 SSID "M32-D002", ret = 32512 wdev_set_bss_role-[rai0] i_am_fh_bss 1 , i_am_bh_bss 0 RTNETLINK answers: No[ 60.930637] [PMF]APPMFInit:: apidx=1, MFPC=1, MFPR=0, SHA256=0 such file or directory set ifname = rai0 hidessid = 0 zsh:1: command not found: wifi_config_save [wdev_set_hidden_ssid] [wdev_set_hidden_ssid] Send HideSSID Command: wifi_config_save rai0 HideSSID 0, ret = 32512 [fill_sec_info]fill_sec_info, kapil: auth = WPA2PSKWPA3PSK len=14 [fill_sec_info]fill_sec_info, encryptype(3) = AES [driver_wext_get_oid]driver_wext_get_oid: oid=0x530 len (4) failed set sec_info: ifname = rai1 auth = WPA2PSKWPA3PSK encryp = AES passphrases = xejkd67379 1-iwpriv rai1 set AuthMode=WPA2PSKWPA3PSK; spi_exception_deinit start zsh:1: command not found: wifi_config_save [wdev_set_sec_and_ssid] [wdev_set_sec_and_ssid] Send AuthMode Command: wifi_config_save rai1 AuthMode WPA2PSKWPA3PSK, ret = 32512 2-iwpriv rai1 set EncrypType=AES; zsh:1: command not found: wifi_config_save [wdev_set_sec_and_ssid] [wdev_set_sec_and_ssid] Send EncrypType[ 61.014012] [PMF]PMF_MakeRsnIeGMgmtCipher: Insert BIP to the group management cipher of RSNIE Command: wifi_c[ 61.024094] wifi_sys_linkdown(), wdev idx = 1 onfig_save rai1 [ 61.024254] ExtEventBeaconLostHandler::FW EVENT (06:ba:d6:50:d0:04), Reason 0x10 EncrypType AES, [ 61.024255] AP Beacon OFF!!! ret = 32512 set[ 61.042966] wifi_sys_linkdown:wdev(type=1,func_idx=1,wdev_idx=1),BssIndex(1) psk: ifname [ 61.051438] hw_ctrl_flow_v2_link_down: wdev_idx=1 = rai1 psk = xejkd67379 [dri[ 61.059118] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 ver_wext_set_psk[ 61.071418] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 ]driver_wext_set_psk : xejkd67379 zsh:1: comman[ 61.087056] wifi_sys_close, wdev idx = 1 d not found: wif[ 61.092755] hw_ctrl_flow_v2_close: wdev_idx=1 i_config_save [[ 61.098518] wifi_sys_open(), wdev idx = 1 driver_wext_set_[ 61.103688] ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 psk] [driver_wex[ 61.110723] phy_oper_init(): operate TxStream = 4, RxStream = 4 t_set_psk] Send WPAPSK Command: [ 61.120002] Caller: wlan_operate_init+0xf8/0x130 [mt7915_mt_wifi_ap] wifi_config_save[ 61.127902] [ 61.127902] phy_mode=177, ch=40, wdev_type=1 rai1 WPAPSK "xe[ 61.134969] ht_cap: ht_cap->HtCapInfo, jkd67379", ret =[ 61.140147] ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 32512 [driver_[ 61.149207] ht_cap: ht_cap->HtCapParm, wext_set_ssid]dr[ 61.154402] mdpu_density=0, ampdu_factor=3 iver_wext_set_ss[ 61.159941] hw_ctrl_flow_v2_open: wdev_idx=1 id : M32-backhau[ 61.165690] wifi_sys_linkup, wdev idx = 1 l-D002 spi end clear /usr/bin/spi spi_exception_deinit switch port=4 egress rate limit off 1650615133: New connection from 192.168.0.1 on port 1883. 1650615133: New client connected from 192.168.0.1 as mosqMaster|3660-D002 (p2, c1, k20, u'admin'). switch port=4 ingress rate limit off [ 61.241273] wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 [ 61.241273] LinkToOmacIdx = 11, LinkToWdevType = 1 [ 61.254231] TRTableInsertMcastEntry:band0 group_idx[1]=1 [ 61.259558] wifi_sys_linkup:wdev(type=1,func_idx=1,wdev_idx=1),BssIndex(1) [ 61.266481] hw_ctrl_flow_v2_link_up: wdev_idx=1 [ 61.271026] (bssUpdateChannel), ucPrimCh=40, ucCentChSeg0=42, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 [ 61.282238] bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8192 [ 61.299198] UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (rai0) [ 61.305684] bcn_buf_init():BcnPkt is allocated!, bcn offload=1 zsh:1: command not found: wifi_config_save [driver_wext_set_ssid] [driver_wext_set_ssid] Send SSID Command: wif[ 61.323923] Set_Fh_Bss_Proc rai1 wdev->MAPCfg.DevOwnRole 0x40 i_config_save rai1 SSID "M32-backhaul-D002", ret = 32512 wdev_set_bss_role-[rai1] i_am_fh_bss 0[ 61.338817] Set_Bh_Bss_Proc rai1 bandIdx = 0 ,DevOwnRole 0x0 , i_am_bh_bss 1 [ 61.355906] Set_Bh_Bss_Proc rai1 bandIdx = 0 ,DevOwnRole 0x40 set ifname = rai1 hidessid = 1 zsh:1: command not found: wifi_config_save [wde[ 61.388045] PhyStatGetRssi: invalid entry. no station link up. v_set_hidden_ssid] [wdev_set_hidden_ssid] Send HideSSID Command: wifi_config_save rai1 HideSSID 1, ret = 32512 [map_config_wireless_setting_msg]radio id=0000 cardid=0002 set MAP_CONF_CONFED [set_bh_wsc_profile]set_bh_wsc_profile send BH config to ra0 [wapp_set_bh_wsc_profile] wpa3 config, set bh config as wpa2[wapp_set_bh_wsc_profile]wapd sends WPAPSK = xejkd67379 send BH config to rai0 [wapp_set_bh_wsc_profile] wpa3 config, set bh config as wpa2[wapp_set_bh_wsc_profile]wapd sends WPAPSK = xejkd67379 send BH config to rai1 [wapp_set_bh_wsc_profile] wpa3 config, set bh config as wpa2[wapp_set_bh_wsc_profile]wapd sends WPAPSK = xejkd67379 [check_redio_conf_status]check_redio_conf_status auto config done [map_build_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_info map_build_ap_he_cap: - Unknow HE Tx Spatial Stream!! map_build_ap_he_cap: - Unknow HE Rx Spatial Stream!! [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability_msg]map_send_metric_reporting_capability_msg [map_build_metric_reporting_info]map_build_metric_reporting_info [map_build_metric_reporting_info]map_build_metric_reporting_info 60 [map_build_chn_pref]map_build_chn_pref [map_send_ch_list_dfs_info]map_send_ch_list_dfs_info [map_handler]WAPP_USER_GET_METRIC_REP_INTERVAL_CAP [map_send_metric_reporting_capability_msg]map_send_metric_reporting_capability_msg [map_build_metric_reporting_info]map_build_metric_reporting_info [map_build_metric_reporting_info]map_build_metric_reporting_info 60 clear /var/nat/blkwan.wan99.clr clear /var/nat/blkwan_pkts.clr clear /var/nat/blkwan_ftp.clr mmi_nat_stop mmi_nat_start NAT nat-draft stop rule end ==NAT Start wan999 ALL== NAT nat-draft stop rule start spi_exception_deinit start spi end clear /usr/bin/spi spi_exception_deinit mmi_nat_stop mmi_nat_start NAT nat-draft stop rule end NAT nat-draft start rule start All Log Alert options from Firewall are disable. nat-draft stop_ip_forward start nat-draft stop_ip_forward end mwlb start mwlb end admin start admin end virtual computer start virtual computer end wanalias start wanalias end portfwd start portfwd end Single DMZ start nat_info.wan_index == 999 restart the SIP ALG modules mac-control start mac-control end discard_ping start discard_ping end inblkwpkts start RTNETLINK answers: Cannot assign requested address inblkwpkts end adjust_mss start adjust_mss end sh /var/nat/BT.clr fwd-recent start fwd-recent end NAT alg start NAT alg end pkt-filter start pkt-filter end pkt-filterv6 start pkt-filterv6 end l7appblk start l7appblk end url-block start fwd_block_url_file_extension url-block end url-block start fwd_block_url url-block end nat-draft start_ip_forward start sh /var/nat/ip_forward.clr nat-draft start_ip_forward end stealth-mode start ping6: sendto: Cannot assign requested address [ 63.359206] PhyStatGetRssi: invalid entry. no station link up. 111111 all 11111111111 0,2 set_sitesuvey... radioid:0,2 rm: can't remove '/tmp/testresult/chstats': No such [ 64.149670] set_AcsScan_proc: bd = 1, rp = 1, bw = 1 file or director[ 64.155222] ch=1 y rm: can't rem[ 64.158348] band[0], thres 2 (ipi_threshold), period 0 (ms) ove '/tmp/testresult/radiostats': No such file or directory 0 interface:ra0 Interface doesn't accept private ioctl... set (8BE2): Invalid argument [ 65.147473] ch_count=1 scan_count=0 ch=2 0 0 [ 65.163680] ch=2 [ 65.165539] ch_count=1 scan_count=0 ch=2 0 0 stealth-mode end spi_exception_deinit start spi end spi_exception_init start spi end pre_spi_mode start spi end security_v6 start security_v6 end Conntrack -F start Wait 2 seconds [ 66.147632] ch_count=2 scan_count=0 ch=3 0 0 [ 66.164184] ch=3 [ 66.166053] ch_count=2 scan_count=0 ch=3 0 0 [ 66.862122] PhyStatGetRssi: invalid entry. no station link up. [ 67.147475] ch_count=3 scan_count=0 ch=4 0 0 [ 67.163689] ch=4 [ 67.165539] ch_count=3 scan_count=0 ch=4 0 0 Conntrack -F end NAT nat-draft stop rule end restart the SIP ALG modules Start Mini-UPNP !! [ 68.147575] ch_count=4 scan_count=0 ch=5 0 0 [ 68.167702] ch=5 [ 68.169585] ch_count=4 scan_count=0 ch=5 0 0 Start Mini-UPNP !! ==NAT Stop wan999 mupnpd== NAT nat-draft stop rule start NAT nat-draft stop rule end ==NAT Start wan999 mupnpd== NAT nat-draft stop rule start NAT nat-draft stop rule end NAT nat-draft start rule start nat-draft stop_ip_forward start func not 'ALL', return discard_ping start discard_ping end sh /var/nat/blkwan.clr inblkwpkts start inblkwpkts end adjust_mss start adjust_mss end sh /var/nat/BT.clr NAT alg start NAT alg end nat-draft start_ip_forward start func not 'ALL', return sh /var/nat/stealth.clr stealth-mode start [ 69.147476] ch_count=5 scan_count=0 ch=6 0 0 [ 69.167706] ch=6 [ 69.169574] ch_count=5 scan_count=0 ch=6 0 0 [ 70.147476] ch_count=6 scan_count=0 ch=7 0 0 [ 70.167664] ch=7 [ 70.169518] ch_count=6 scan_count=0 ch=7 0 0 [ 71.147474] ch_count=7 scan_count=0 ch=8 0 0 [ 71.167691] ch=8 [ 71.169544] ch_count=7 scan_count=0 ch=8 0 0 stealth-mode end security_v6 start security_v6 end NAT nat-draft stop rule end [ 72.147541] ch_count=8 scan_count=0 ch=9 0 0 [ 72.171759] ch=9 [ 72.173652] ch_count=8 scan_count=0 ch=9 0 0 [ 73.147466] ch_count=9 scan_count=0 ch=10 0 0 [ 73.171688] ch=10 [ 73.173622] ch_count=9 scan_count=0 ch=10 0 0 [ 74.147482] ch_count=10 scan_count=0 ch=11 0 0 [ 74.171692] ch=11 [ 74.173626] ch_count=10 scan_count=0 ch=11 0 0 [ 74.425458] PhyStatGetRssi: invalid entry. no station link up. [ 75.147552] ch_count=11 scan_count=0 ch=12 0 0 [ 75.171695] ch=12 [ 75.173632] ch_count=11 scan_count=0 ch=12 0 0 ## Lunching system normally completed! ## [ 76.147469] ch_count=12 scan_count=0 ch=13 0 0 [ 76.171745] ch=13 [ 76.173689] ch_count=12 scan_count=0 ch=13 0 0 ZZZZZ 77777: mydlink [ 77.828728] PhyStatGetRssi: invalid entry. no station link up. Enter GetMyDLinkSettings_put Enter GetMyDLinkSettings_get Enter GetNetworkSettings_put Enter GetNetworkSettings_get Enter GetWanSettings_put GetWanSettings_WANID:WAN01 GetWanSettings_WAN_INDEX=99 Enter GetWanSettings_get [ 81.176450] PhyStatGetRssi: invalid entry. no station link up. [ 84.513142] PhyStatGetRssi: invalid entry. no station link up. [ 87.911830] PhyStatGetRssi: invalid entry. no station link up. 2 interface:rai0 [ 89.173414] set_AcsScan_proc: bd = 2, rp = 1, bw = 1 [ 89.178514] ch=36 [ 89.180454] band[0], thres 2 (ipi_threshold), period 1000 (ms) Interface doesn't accept private ioctl... set (8BE2): Invalid argument [ 90.183789] ch=40 [ 90.185741] ch_count=1 scan_count=0 ch=40 0 0 [ 91.183698] ch=44 [ 91.185660] ch_count=2 scan_count=0 ch=44 0 0 [ 91.287152] PhyStatGetRssi: invalid entry. no station link up. [ 92.183790] ch=48 [ 92.185778] ch_count=3 scan_count=0 ch=48 0 0 [ 94.647021] PhyStatGetRssi: invalid entry. no station link up. [ 98.253200] PhyStatGetRssi: invalid entry. no station link up. [ 98.284957] PhyStatGetRssi: invalid entry. no station link up. [ 101.636297] PhyStatGetRssi: invalid entry. no station link up. [ 104.996720] PhyStatGetRssi: invalid entry. no station link up. [ 108.379176] PhyStatGetRssi: invalid entry. no station link up. [ 111.816269] PhyStatGetRssi: invalid entry. no station link up. [ 115.193192] PhyStatGetRssi: invalid entry. no station link up. [ 118.571515] PhyStatGetRssi: invalid entry. no station link up. [ 122.019000] PhyStatGetRssi: invalid entry. no station link up. [ 125.470407] PhyStatGetRssi: invalid entry. no station link up. [ 128.874429] PhyStatGetRssi: invalid entry. no station link up. [ 132.272667] PhyStatGetRssi: invalid entry. no station link up. [ 132.293830] PhyStatGetRssi: invalid entry. no station link up. [ 135.724590] PhyStatGetRssi: invalid entry. no station link up. [ 139.135325] PhyStatGetRssi: invalid entry. no station link up. [ 142.540711] PhyStatGetRssi: invalid entry. no station link up. [ 145.944176] PhyStatGetRssi: invalid entry. no station link up. [ 149.334230] PhyStatGetRssi: invalid entry. no station link up. [ 152.740203] PhyStatGetRssi: invalid entry. no station link up. [ 156.214063] PhyStatGetRssi: invalid entry. no station link up. [ 159.616936] PhyStatGetRssi: invalid entry. no station link up. [ 163.000333] PhyStatGetRssi: invalid entry. no station link up. [ 166.406637] PhyStatGetRssi: invalid entry. no station link up. [ 166.423577] PhyStatGetRssi: invalid entry. no station link up. [ 169.830095] PhyStatGetRssi: invalid entry. no station link up. [ 173.212358] PhyStatGetRssi: invalid entry. no station link up.

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING

Space for additional notes, links to forum threads or other resources.

...

Add tags below, then remove this fixme.

How to add tags

EXAMPLETAG

D-Link EAGLE PRO AI R32 A1

Supported Versions

Experimental Versions

Hardware Highlights

Installation

Flashing via Recovery Web Interface:

Flashing via uBoot:

Flash Layout

Debricking

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags