Aztech DSL7002GRV(S)

Aztech DSL7002GRV(S) Flash Layout
Layer 0 ?: ? 128MiB
Layer 1 mtd3 nvram 128KiB mtd1 rootfs_update 62848KiB mtd0 rootfs 62848KiB [Unused?] 4839KiB mtd2 data 4096KiB
mountpoint /
filesystem JFFS2
Layer 2 nvram rootfs_update rootfs data
Size in KiB 128KiB 62848KiB 62848KiB 4096KiB
mountpoint none none / /data
filesystem none JFFS2 JFFS2 JFFS2

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS ZQDN 300H PHYE DINT LASY USYN MSYN LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN FPS0 BT06 0001 BT07 0492 NAN3 RFS2 NAN5 CFE version 1.0.38-114.185 for BCM96362 (32bit,SP,BE) Build Date: Mon Jul 8 15:36:58 SGT 2013 (uday@rdfwdev2.aztech.com) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB External switch id = 53125 Chip ID: BCM6362B0, MIPS: 400MHz, DDR: 333MHz, Bus: 166MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : 192.168.2.254 Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 5 Boot image (0=latest, 1=previous) : 0 Board Id (0-13) : 96362ADVN2xh Number of MAC Addresses (1-32) : 12 Base MAC Address : 00:00:00:00:00:00 PSI Size (1-512) KBytes : 512 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 128 Auxillary File System Size Percent: 0 Main Thread Number [0|1] : 0 Serial Number (13 digits) : xxxxxxxxxxxxx Current Mode (F|N) : N WPS Device Pin : "xxxxxxxx" Voice Board Configuration (0-2) : LE88266 *** Press any key to stop auto run (5 seconds) *** Auto run second count down: 0 Booting from latest image (0xbbd80000) ... Decompression OK! Entry at 0x8032a950 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x8032a950 Linux version 2.6.30 (uday@rdfwdev2.aztech.com) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 SMP PREEMPT Mon Jul 8 15:37:45 SGT 2013 BCM Flash API. Flash device is not found. 96362ADVN2xh prom init CPU revision is: 0002a070 (Broadcom4350) DSL SDRAM reserved: 0x100000 Determined physical RAM map: memory: 07f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00007f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00007f00 On node 0 totalpages: 32512 free_area_init_node: node 0, pgdat 803fce10, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 222 pages used for memmap Normal zone: 28194 pages, LIFO batch:7 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32258 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 512 (order: 9, 2048 bytes) console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Memory: 124200k/130048k available (3210k kernel code, 5660k reserved, 826k data, 152k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Jul 8 2013 14:48:49 CPU revision is: 0002a070 (Broadcom4350) Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Calibrating delay loop... 402.43 BogoMIPS (lpj=201216) Brought up 2 CPUs net_namespace: 1140 bytes NET: Registered protocol family 16 Total Flash size: 0K with -1 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D3hot D3cold pci 0000:00:00.0: PME# disabled pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0xa0000000-0xa00fffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 skbFreeTask created successfully BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Jul 8 2013 14:56:41 initialized Broadcom GBPM v0.1 Jul 8 2013 14:56:42 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.11) msgmni has been set to 242 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v2.0 Failed to read image tag from flash Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=01f1001d After: NandSelect=40000001, nandConfig=15142200 Block size=00020000, erase shift=17 NAND Config: Reg=15142200, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 5363444f timing2 not adjusted: 00000fc6 BrcmNAND mfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0 Found NAND on CS0: ACC=f3000000, cfg=15142200, flashId=01f1001d, tim1=5363444f, tim2=00000fc6 BrcmNAND version = 0x0202 128MB @00000000 B4: NandSelect=40000001, nandConfig=15142200, chipSelect=0 brcmnand_read_id: CS0: dev_id=01f1001d After: NandSelect=40000001, nandConfig=15142200 Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f3000000 page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 2.2 NAND flash size 128MB @18000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=87a4ad90, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 nand_read_bbt: Bad block at 0x05ae0000 brcmnandCET: Status -> Deferred brcmnand_scan 99 Creating 4 MTD partitions on "brcmnand.0": 0x000003d80000-0x000007ae0000 : "rootfs" 0x000000020000-0x000003d80000 : "rootfs_update" 0x000007b00000-0x000007f00000 : "data" 0x000000000000-0x000000020000 : "nvram" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usb usb1: USB connect, address 1 USB Device Path: 0 my_usb_info: 0X0000 az_usb1_attached: 0x0000, az_usb2_attached: 0x0000 ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usb usb2: USB connect, address 1 USB Device Path: 0 my_usb_info: 0X0000 az_usb1_attached: 0x0000, az_usb2_attached: 0x0000 usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry kerSysScreenPciDevices: 0x14e4:0x435f:(slot 0) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected kerSysScreenPciDevices: 0x14e4:0x6362:(slot 0) detected kerSysScreenPciDevices: 0x14e4:0x4331:(slot 0) detected SES: Button Interrupt 0x2 is enabled sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=2 SES: LED GPIO 0xc00f is enabled brcm_board_init: isShared=0, rstToDflt_irq=0 Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000100 (irq = 11) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 12) is a BCM63XX Total # RxBds=848 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmPktDma_init: Broadcom Packet DMA Library initialized bcmxtmrt: Broadcom BCM6362B0 ATM/PTM Network Device v0.3 Jul 8 2013 14:55:24 IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 152k freed init started: BusyBox v1.17.2 (2013-07-08 15:06:37 SGT) starting pid 222, tty '': '/etc/init.d/rcS' usbfs: unrecognised mount option "defaults" or missing value usbfs: mount parameter error. starting pid 228, tty '': '-/bin/sh' BusyBox v1.17.2 (2013-07-08 15:06:37 SGT) built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... Loading Samba configuration files ... chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Jul 8 2013 14:54:36 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=134217728B (128MB), buf_mem_size=20132655B (19MB), num of buffers=9460, buf size=2128 Broadcom BPM Module Char Driver v0.1 Jul 8 2013 14:51:56 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jul 8 2013 14:54:36 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jul 8 2013 14:54:36 chipId 0x636220B0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jul 8 2013 14:54:23 Registered <241> Enabling SMISBUS PHYS_FAP_BASE[0] is 0x14001000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa5d9c4f0 0xa5d9c4f0 Allocated FAP0 GSO Buffers (0xA5DAD578) : 1048576 bytes @ 0xA5E00000 Allocated FAP0 TM SDRAM Queue Storage (a5dad57c) : 341376 bytes @ a5f00000 [NTC fapProto] fapReset : Reset FAP Protocol layer [FAP0] DSPRAM : stack <0x80004000><1536>, global <0x80004600><3760>, free <2896>, total<8192> [FAP0] PSM : addr<0xE0010000>, used <24216>, free <8552>, total <32768> [FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE00045F8 [FAP0] GSO Buffer set to 0xA5E00000 [FAP0] FAP BPM Initialized. fapDrv_construct: FAP0: pManagedMemory=b1010650. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry bcm63xx_enet_probe unit 1 pDevCtrl 85c6fc20 85c6fc20 chip 0x6362 Broadcom BCM6362B0 Ethernet Network Device v0.1 Jul 8 2013 14:55:09 fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b1010650 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb1010650 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b1011910 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb1011910 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: 00:26:75:C2:19:2B eth1: MAC Address: 00:26:75:C2:19:2B eth2: MAC Address: 00:26:75:C2:19:2B eth3: MAC Address: 00:26:75:C2:19:2B eth4: MAC Address: 00:26:75:C2:19:2B [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Jul 8 2013 14:51:56 Registered <245> --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=6149 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_map.bin srom rev:8 wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16 wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl1: allocskbmode=1 currallocskbsz=3500 wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm4331_map.bin srom rev:9 wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16 wl1: Broadcom BCM4331 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.0 dgasp: kerSysRegisterDyingGaspHandler: wl1 registered Endpoint: endpoint_init entry Endpoint: endpoint_init COMPLETED Broadcom 802.1Q VLAN Interface, v0.1 ===== Release Version 4.12L.08 (build timestamp 130708_1538) ===== ssk:error:27.138:lck_checkBeforeEntry:225:lock reBOS: Enter bosInit quired during cmBOS: Exit bosInit sObj_getNextInSuendpoint_open COMPLETED bTreeFlags wait instruction: disabled Ethernet Auto Power Down and Sleep is disabled Adaptive Voltage Scaling is now disabled sendto: Network is unreachable ip_tables: (C) 2000-2006 Netfilter Core Team ip6_tables: (C) 2000-2006 Netfilter Core Team br0: starting userspace STP failed, starting kernel STP Netfilter messages via NETLINK v0.30. device eth1 entered promiscuous mode ADDRCONF(NETDEV_UP): eth1: link is not ready device eth2 entered promiscuous mode ADDRCONF(NETDEV_UP): eth2: link is not ready device eth3 entered promiscuous mode ADDRCONF(NETDEV_UP): eth3: link is not ready device eth4 entered promiscuous mode ADDRCONF(NETDEV_UP): eth4: link is not ready device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state WLmngr Daemon is running optarg=0 shmId=0 device wl1 entered promiscuous mode wlevt is ready for new msg... br0: topology change detected, propagating br0: port 6(wl1) entering forwarding state BcmAdsl_Initialize=0xC0263BB0, g_pFnNotifyCallback=0xC0298644 Version Number is 293.6.1-010 Serial Number is xxxxxxxxxxxxx pSdramPHY=0xA7FFFFF8, 0x39434 0xDEADBEEF *** XfaceOffset: 0x21F90 => 0x21F90 *** *** PhySdramSize got adjusted: 0x8339C => 0x98D48 *** AdslCoreSharedMemInit: shareMemSize=422541(422544) AdslCoreHwReset: pLocSbSta=83e68000 bkupThreshold=1600 AdslCoreHwReset: AdslOemDataAddr = 0xA7F783D4 Version Number is 293.6.1-010 Serial Number is xxxxxxxxxxxxx ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered fapDrv_psmAlloc: fapIdx=0, size: 1600, offset=b1012be0 bytes remaining 584 XTM Init: 200 rx BDs at 0xb1012be0 fapDrv_psmAlloc: fapIdx=0, size: 128, offset=b1013220 bytes remaining 456 XTM Init: 16 rx BDs at 0xb1013220 ADDRCONF(NETDEV_UP): eth0: link is not ready Could not get lock! WPS Device PIN = xxxxxxxx br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state monitor task is initialized pid= 335 killall: hspotap: no process killed br0: port 5(wl0) entering disabled state Setting SSID: "Singtel7002-192B" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" wlctl: Unsupported device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state ssk:error:46.873:initVodslBoundIpIfWanSideUpLocked:813:Failed to get WAN Connection object Note: Loading 6300 MDK (default) driver for 6362 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x0; config_pbmp = 0x10 Switch MDK link poll thread: unit=1; phypbmp=0x1f Initializing unit 0 in unmanaged mode ifconfig: wl1.1: error fetching interface information: Device not found ifconfig: wl1.2: error fetching interface information: Device not found ifconfig: wl1.3: error fetching interface information: Device not found unrecognized msg 0x10000250 ssk:error:48.778:ssk_main:732:cannot handle msg type 0x10000802 tr69c:error:48.783:updateTr69cCfgInfo:767:could not build full path to (null) acsd: selected channel spec: 0x1003 wlmngr: events/1 is running as Real Time process. wlmngr: events/0 is running as Real Time process. br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state killall: hspotap: no process killed wlctl: Not Permitted wlctl: Undefined error br0: port 5(wl0) entering disabled state Setting SSID: "Singtel7002-192B" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" wlctl: Unsupported device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: topology change detected, propagating br0: port 5(wl0) entering forwarding state ifconfig: wl1.1: error fetching interface information: Device not found ifconfig: wl1.2: error fetching interface information: Device not found ifconfig: wl1.3: error fetching interface information: Device not found acsd: selected channel spec: 0x1009 error opening file /var/voice/regstatus0.txt! error opening file /var/voice/regstatus1.txt! wlmngr: events/1 is running as Real Time process. wlmngr: events/0 is running as Real Time process. ARL table flush done Success br0: port 6(wl1) entering disabled state device wl1 left promiscuous mode br0: port 6(wl1) entering disabled state device wl1 entered promiscuous mode br0: topology change detected, propagating br0: port 6(wl1) entering forwarding state killall: hspotap: no process killed wlctl: Not Permitted wlctl: Undefined error br0: port 6(wl1) entering disabled state Setting SSID: "Singtel7002(5G)-192B" Setting SSID: "wl1_Guest1" Setting SSID: "wl1_Guest2" Setting SSID: "wl1_Guest3" wlctl: Unsupported device wl1 left promiscuous mode br0: port 6(wl1) entering disabled state device wl1 entered promiscuous mode br0: topology change detected, propagating br0: port 6(wl1) entering forwarding state acsd: selected channel spec: 0x100b acsd: selected channel spec: 0xd92e wlmngr: events/1 is running as Real Time process. wlmngr: events/0 is running as Real Time process. br0: port 6(wl1) entering disabled state device wl1 left promiscuous mode br0: port 6(wl1) entering disabled state device wl1 entered promiscuous mode br0: topology change detected, propagating br0: port 6(wl1) entering forwarding state BCM96362 Broadband Router Login: killall: hspotap: no process killed wlctl: Not Permitted wlctl: Undefined error wlctl: Unsupported br0: port 6(wl1) entering disabled state Setting SSID: "Singtel7002(5G)-192B" Setting SSID: "wl1_Guest1" Setting SSID: "wl1_Guest2" Setting SSID: "wl1_Guest3" wlctl: Unsupported device wl1 left promiscuous mode br0: port 6(wl1) entering disabled state device wl1 entered promiscuous mode br0: topology change detected, propagating br0: port 6(wl1) entering forwarding state acsd: selected channel spec: 0x1001 acsd: selected channel spec: 0xd926 wlmngr: events/1 is running as Real Time process. wlmngr: events/0 is running as Real Time process. sendto: Network is unreachable ARL table flush done Success


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1