Aruba AP-303
The Aruba AP-303 is a 2×2 802.11ac Wave 2 access point. It is fairly powerful with a quad-core ARM processor and 512 MB of memory. The Aruba Instant On AP11 is a much cheaper version of this device and is based on the same platform, the OpenWrt firmware for Aruba AP-303 can also be flashed onto the Aruba Instant On AP11.
Supported Versions
Hardware Highlights
Installation
You will need a special console cable (see below in Section “Serial”) and an UART-Adapter:
- Get the OpenWrt initramfs image. Rename it to
ipq40xx.ariand put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. In case, you connect your server via DHCP like your internet provider router, the exact setting of the IP is optional. You just have to know it and change it in step 3 accordingly. - Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. In case, you connected the AP-303 to your DHCP-Router enter the following first into the serial console to get the AP-303 IP-address>:
$ dhcp
- Configure the bootargs and bootcmd for OpenWrt
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; set fdt_high 0x87000000; bootm 0x85000000" # Substitute the following IP-addresses as mentioned Step 1 and 2, in case, you are using DHCP. $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv
- Load OpenWrt into RAM
$ run ramboot_openwrt
(Note that after the TFTP transfer completes, there will be an error displayed: “Invalid image format version”. It can be ignored.)
- After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmpfolder on the device. - Flash OpenWrt
$ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin
In case you are using DHCP, in the console of Openwrt change “option proto 'static'” to “option proto 'dhcp'” for the lan interface via
$ vi /etc/config/network # Then reload and connect. $ service network reload
Upgrading OpenWrt
Debricking
Failsafe mode
Basic configuration
→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The Aruba AP-303 has the following buttons:
| BUTTON | Event |
|---|---|
| Reset | reset |
Hardware
Info
Photos
Front:
Insert photo of front of the casing
Back:
Insert photo of back of the casing
Backside label:
Insert photo of backside label
Opening the case
Note: This will void your warranty!
Remove the 4 screwas on the back of the device. The metal casing can be lift up. The PCB is secured with a single screw in the middle of the PCB.
Main PCB:
Insert photo of PCB
Serial
→ port.serial general information about the serial port, serial port cable, etc.
To connect to the serial console, you can solder to the labled pads next to the USB port or use your Aruba supplied UART adapter.
Do NOT plug a standard USB cable into the Console labled USB-port! Aruba/HPE simply put UART on the micro-USB pins. You can solder (or luster clamp or bread-board) yourself an adapter cable by stripping an old Micro-USB-B-cable:
| USB pin | UART usage |
|---|---|
| VCC | Unused (not connected) |
| D+ | TX |
| D- | RX |
| GND | GND |
The console setting in bootloader and OS is 9600 8N1. Voltage level is 3.3V. Cheap USB-UART Adapter have failed to work.
To enable a full list of commands in the U-Boot “help” command, execute the literal “diag” command.
Hardware mods
None so far.
Bootlogs
OEM bootlog (AP-11 firmware)
APBoot 2.5.0.2 (build 70487) Built: 2019-05-14 at 12:27:57 Model: AP11 DRAM: 512 MiB Flash: Detected MX25R3235F: with write protection total 4 MiB NAND: 128 MiB Power: DC Net: eth0 Radio: ipq4019#0, ipq4019#1 FIPS: passed Hit <Enter> to stop autoboot: 2 1 0 Checking image @ 0x0 Copying image from 0x84000000 Image is signed; verifying checksum... passed SHA2 Signature available Signer Cert OK Policy Cert OK RSA signature verified using SHA2. Uncompressing Kernel Image ... OK [ 0.000000] [ 0.000000] Instant On [ 0.000000] ArubaOS Version 1.4.1.0 (build 74478 / label #74478) [ 0.000000] Built by p4build@pr-hpn-build01 on 2020-02-27 at 23:01:18 AST (gcc version 5.3.0) [ 0.000000] [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.016929] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.052360] i2c-gpio driver registered [ 2.464873] 3 ofpart partitions found on MTD device 7980000.qcom,nand [ 2.533728] Creating 3 MTD partitions on "7980000.qcom,nand": [ 2.602465] 0x000000000000-0x000002000000 : "aos0" [ 2.701779] 0x000002000000-0x000004000000 : "aos1" [ 2.788467] 0x000004000000-0x000008000000 : "ubifs" [ 2.922421] m25p80 spi0.0: found mx25r3235f, expected n25q128a11 [ 3.010854] Found AT97SC3203 on MSM-I2C-v2-adapter [ 3.066098] Key type dns_resolver registered [ 3.106833] Registering SWP/SWPB emulation handler [ 4.430268] Watchdog run with TZ supported gpio reset [ 4.512679] Starting Kernel SHA1 KAT ... [ 4.547147] Completed Kernel SHA1 KAT [ 4.594172] Starting Kernel HMAC-SHA1 KAT ... [ 4.644239] Starting Kernel DES KAT ...[ 4.689957] Completed Kernel DES KAT [ 4.733695] Starting Kernel AES KAT ... [ 4.777397] Completed Kernel AES KAT [ 4.777397] [ 4.840923] Starting Kernel AESGCM KAT ... [ 4.887747] Completed Kernel AESGCM KAT [ 4.937068] Completed Kernel HMAC-SHA1 KAT Thu Jan 1 00:00:00 PST 1970 Populate AP type info Domain Name: InstantOn.arubainstanton.com Current OEM Name : Instant On Disabling ipv6 for devices by default AP-type has_ble_support: ONBOARD. IPv6 capability is supported for devices No panic info available Writing /dev/ttyMSM1 into /tmp/ble_port Enabling ble_daemon and ble_relay via nanny apfcutil: sector CACHE: Cache uninitialized apfcutil: sector RAP: Cache uninitialized apfcutil: sector FAT: Cache uninitialized apfcutil: sector DRT: Cache uninitialized apfcutil: sector SCRATCH: Cache uninitialized Check backup ENV. apfcutil: sector MESH Prov: Cache uninitialized Installing glenmorangie ethernet driver [ 15.999045] edma module_init Enter non-FIPS mode Cfg len is 0 Configuration file is empty, turning on default services... Mesh is enabled by default on Instant-On The AP is in factory default status Starting watchdog process... Aruba watchdog daemon started [4 thread(s)] touching file /tmp/ip_mode_0 Enable IPv6 for the Master v6 discovery Enabling DHCPv6 ... ble_ready NOT present @init .... Checking country code. Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet Ethernet uplink not active yet No uplink active. Becoming Mesh Point killall: ble_daemon: no process killed Factory default ap without uplink, it will become a point. copy[ 51.902199] uol: module license 'Proprietary' taints kernel. [ 51.978267] Disabling lock debugging due to kernel taint ing bootuplog ... [ 52.042806] uol_init_driver:344 HW offload not applicable, AP will use cutting through path! allow PAPI set device anul0 mtu to 2000 notify asap_mod 3g no present... AP is not onboarded. SMB iap master unset. Enabling IPv6 for devices... IP mode is v4-only... apdot1x authentication is not enabled Starting DHCP Compressing all files in the /etc/httpd directory... Done. Starting Webserver bind: Transport endpoint is not connected bind: Transport endpoint is not connected bind: Transport endpoint is not connected Put ntpdate to the nannylist. AP rebooted caused by cold HW reset(power loss) shutting down watchdog process (nanny will restart it)... <<<<< Welcome to the Access Point >>>>> Power supply mode is DC, USB Modem is not present. Completed SW FIPS KAT test ble_ready NOT present @init ....
OpenWrt bootlog
APBoot 2.4.1.10 (build 65756) Built: 2018-07-11 at 21:04:12 Model: AP-303 DRAM: 512 MiB Flash: Detected MX25R3235F: with write protection total 4 MiB NAND: 128 MiB Power: POE Net: eth0 Radio: ipq4019#0, ipq4019#1 FIPS: passed Hit <Enter> to stop autoboot: 0 No size specified -> Using max size (3047424) Uncompressing Kernel Image ... OK ipq: fdt fixup unable to find compatible node [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.176 (builder@buildhost) (arm-openwrt-linux-mus lgnueabi-gcc (OpenWrt GCC 11.2.0 r20134-5f15225c1e) 11.2.0, GNU ld (GNU Binutils ) 2.37) #0 SMP Thu Apr 27 20:28:15 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Aruba AP-303 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x0000000087dfffff] [ 0.000000] node 0: [mem 0x0000000087e00000-0x0000000087ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s31116 r8192 d22132 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129920 [ 0.000000] Kernel command line: console=ttyMSM1,9600n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, l inear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 506824K/524288K available (6479K kernel code, 608K rwdata , 956K rodata, 1024K init, 246K bss, 17464K reserved, 0K cma-reserved, 0K highme m) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000009] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 43980 46511096ns [ 0.000027] Switching to timer-based delay loop, resolution 20ns [ 0.000347] Calibrating delay loop (skipped), value calculated using timer fr equency.. 96.00 BogoMIPS (lpj=480000) [ 0.000374] pid_max: default: 32768 minimum: 301 [ 0.000562] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linea r) [ 0.000585] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001657] CPU: Testing write buffer coherency: ok [ 0.002057] qcom_scm: convention: smc legacy [ 0.003065] Setting up static identity map for 0x80300000 - 0x8030003c [ 0.003245] rcu: Hierarchical SRCU implementation. [ 0.003533] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.003908] smp: Bringing up secondary CPUs ... [ 0.007612] smp: Brought up 1 node, 4 CPUs [ 0.007636] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.007647] CPU: All CPU(s) started in SVC mode. [ 0.013485] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.013676] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.013706] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.013992] pinctrl core: initialized pinctrl subsystem [ 0.015856] NET: Registered protocol family 16 [ 0.016208] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017434] thermal_sys: Registered thermal governor 'step_wise' [ 0.017892] cpuidle: using governor ladder [ 0.017954] cpuidle: using governor menu [ 0.035938] gpio-454 (PHY-reset): hogged as output/high [ 0.044679] cryptd: max_cpu_qlen set to 1000 [ 0.049208] usbcore: registered new interface driver usbfs [ 0.049284] usbcore: registered new interface driver hub [ 0.049347] usbcore: registered new device driver usb [ 0.049401] pps_core: LinuxPPS API ver. 1 registered [ 0.049414] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti <giometti@linux.it> [ 0.049443] PTP clock support registered [ 0.051483] clocksource: Switched to clocksource arch_sys_counter [ 0.052517] NET: Registered protocol family 2 [ 0.052782] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear ) [ 0.053927] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.053995] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.054058] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.054147] TCP: Hash tables configured (established 4096 bind 4096) [ 0.054282] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054325] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054612] NET: Registered protocol family 1 [ 0.054663] PCI: CLS 0 bytes, default 64 [ 0.057183] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.062226] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.062254] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 0.192185] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 48) [ 0.195222] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.195248] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.196705] tcsr 1953000.ess_tcsr: setting ess interface select = 1 [ 0.196813] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.196909] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.197240] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.199160] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.199211] msm_serial 78af000.serial: uartclk = 1843200 [ 0.199272] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 34, base_baud = 115200) is a MSM [ 0.199804] msm_serial 78b0000.serial: msm_serial: detected port #1 [ 0.199846] msm_serial 78b0000.serial: uartclk = 1843200 [ 0.199896] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 35, base_baud = 115200) is a MSM [ 0.199927] msm_serial: console setup on port #1 [ 6.934428] printk: console [ttyMSM1] enabled [ 6.991219] msm_serial: driver initialized [ 7.047104] loop: module loaded [ 7.091518] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 7.126096] nand: Macronix MX30LF1G18AC [ 7.205245] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz e: 64 [ 7.247976] Block protection check failed [ 7.339674] 3 fixed-partitions partitions found on MTD device qcom_nand.0 [ 7.388599] Creating 3 MTD partitions on "qcom_nand.0": [ 7.469834] 0x000000000000-0x000002000000 : "aos0" [ 7.579083] 0x000002000000-0x000004000000 : "ubi" [ 7.637330] 0x000004000000-0x000008000000 : "aruba-ubifs" [ 7.744733] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 7.753857] spi-nor spi0.0: mx25r3235f (4096 Kbytes) [ 7.817804] 15 fixed-partitions partitions found on MTD device spi0.0 [ 7.877155] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 7.953162] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 8.030855] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 8.108392] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions [ 8.187036] Creating 15 MTD partitions on "spi0.0": [ 8.264610] 0x000000000000-0x000000040000 : "sbl1" [ 8.322625] 0x000000040000-0x000000060000 : "mibib" [ 8.380944] 0x000000060000-0x0000000c0000 : "qsee" [ 8.438149] 0x0000000c0000-0x0000000d0000 : "cdt" [ 8.496403] 0x0000000d0000-0x0000000e0000 : "ddrparams" [ 8.553681] 0x0000000e0000-0x0000000f0000 : "ART" [ 8.614130] 0x0000000f0000-0x0000001e0000 : "appsbl" [ 8.672478] 0x0000001e0000-0x0000001f0000 : "mfginfo" [ 8.733016] 0x0000001f0000-0x000000200000 : "apcd" [ 8.792332] 0x000000200000-0x000000380000 : "osss" [ 8.848503] 0x000000380000-0x000000390000 : "appsblenv" [ 8.905791] 0x000000390000-0x0000003a0000 : "pds" [ 8.967193] 0x0000003a0000-0x0000003b0000 : "fcache" [ 9.025608] 0x0000003b0000-0x0000003c0000 : "u-boot-env-bak" [ 9.085967] 0x0000003f0000-0x000000400000 : "u-boot-env" [ 9.392164] i2c /dev entries driver [ 9.392440] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 9.422297] sdhci: Secure Digital Host Controller Interface driver [ 9.498527] sdhci: Copyright(c) Pierre Ossman [ 9.571434] sdhci-pltfm: SDHCI platform and OF driver helper [ 9.628674] NET: Registered protocol family 10 [ 9.694804] Segment Routing with IPv6 [ 9.744463] NET: Registered protocol family 17 [ 9.789186] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 9.841221] 8021q: 802.1Q VLAN Support v1.8 [ 9.998571] Registering SWP/SWPB emulation handler [ 10.057786] UBI: auto-attach mtd1 [ 10.103730] ubi0: attaching mtd1 [ 10.579460] ubi0: scanning is finished [ 10.598687] ubi0 warning: 0xc06f920c: cannot reserve enough PEBs for bad PEB handling, reserved 8, need 20 [ 10.613327] ubi0: attached mtd1 (name "ubi", size 32 MiB) [ 10.726477] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 10.792054] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 10.873311] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 10.955592] ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0 [ 11.036858] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 [ 11.111844] ubi0: max/mean erase counter: 9/2, WL threshold: 4096, image sequence number: 2019240267 [ 11.196228] ubi0: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 8 [ 11.307706] ubi0: background thread "ubi_bgt0d" started, PID 121 [ 11.418026] block ubiblock0_1: created from ubi0▒[ 11.560223] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 11.562320] Freeing unused kernel memory: 1024K [ 11.651740] Run /sbin/init as init process [ 12.789765] init: Console is alive [ 12.790087] init: - watchdog - [ 13.838301] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 13.956991] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 103 [ 13.967658] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 14.035566] init: - preinit - [ 15.043789] ess_edma c080000.edma eth0: Link is Down [ 15.074344] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 19.192909] ess_edma c080000.edma eth0: Link is Up - 1Gbps/Full - flow contro l rx/tx [ 19.193917] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.346900] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 19.347161] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 183 [ 19.505020] UBIFS (ubi0:2): recovery needed [ 19.754242] UBIFS (ubi0:2): recovery completed [ 19.754675] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "root fs_data" [ 19.793957] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O u nit sizes: 2048 bytes/2048 bytes [ 19.888727] UBIFS (ubi0:2): FS size: 21078016 bytes (20 MiB, 166 LEBs), journ al size 1015809 bytes (0 MiB, 8 LEBs) [ 20.007490] UBIFS (ubi0:2): reserved for root: 995566 bytes (972 KiB) [ 20.130409] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID B025B A74-A4FC-4887-903D-6CEECBED8AC4, small LPT model [ 20.212281] mount_root: switching to ubifs overlay [ 20.359105] urandom-seed: Seeding with /etc/urandom.seed [ 20.600254] ess_edma c080000.edma eth0: Link is Down [ 20.619726] procd: - early - [ 20.648895] procd: - watchdog - [ 21.309461] procd: - watchdog - [ 21.594421] procd: - ubus - [ 21.935594] random: ubusd: uninitialized urandom read (4 bytes read) [ 21.947386] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.000809] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.081715] procd: - init - Please press Enter to activate this console. [ 22.956609] random: ubusd: uninitialized urandom read (4 bytes read) [ 22.956896] random: ubus: uninitialized urandom read (4 bytes read) [ 23.131084] random: jshn: uninitialized urandom read (4 bytes read) [ 23.171046] kmodloader: loading kernel modules from /etc/modules.d/* [ 23.276090] urngd: v1.0.2 started. [ 23.300122] Loading modules backported from Linux version v5.15.92-0-ge515b99 02f5f [ 23.309311] Backport generated by backports.git v5.15.92-1-0-gdfe0f60c [ 23.358694] random: crng init done [ 23.462379] PPP generic driver version 2.4.2 [ 23.478105] random: 20 urandom warning(s) missed due to ratelimiting [ 23.519861] NET: Registered protocol family 24 [ 25.323487] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 25.323545] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 25.425302] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337b b1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regd ump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc -CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6 b2b5c5b [ 25.643819] ath10k_ahb a000000.wifi: Loading BDF type 0 [ 25.863851] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 d2e9d 359 [ 27.215830] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 27.215900] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 27.335771] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 27.361846] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 27.666754] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1 [ 29.512453] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 29.512519] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 29.614258] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 29.831588] ath10k_ahb a800000.wifi: Loading BDF type 0 [ 30.052359] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 d2e9d359 [ 31.404577] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 31.404632] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 31.524406] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 31.551269] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 31.816276] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1 [ 31.988506] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.802619] br-lan: port 1(eth0) entered blocking state [ 39.802677] br-lan: port 1(eth0) entered disabled state [ 39.851196] device eth0 entered promiscuous mode [ 42.407776] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 42.407838] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 42.527448] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 42.553793] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 43.000441] ath10k_ahb a800000.wifi: rts threshold -1 [ 43.004474] ath10k_ahb a800000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 43.031815] ess_edma c080000.edma eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 43.180153] br-lan: port 1(eth0) entered blocking state [ 43.274630] br-lan: port 1(eth0) entered forwarding state [ 43.334463] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 43.401172] br-lan: port 2(wlan1) entered blocking state [ 43.406032] ath10k_ahb a800000.wifi: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 43.477793] br-lan: port 2(wlan1) entered disabled state [ 43.652156] device wlan1 entered promiscuous mode [ 45.195928] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 45.195986] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 45.316750] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 45.342216] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752' [ 45.837361] ath10k_ahb a000000.wifi: rts threshold -1 [ 45.842398] ath10k_ahb a000000.wifi: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 45.889162] br-lan: port 3(wlan0) entered blocking state [ 46.017124] br-lan: port 3(wlan0) entered disabled state [ 46.082840] device wlan0 entered promiscuous mode [ 48.263684] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 48.264205] br-lan: port 3(wlan0) entered blocking state [ 48.328581] br-lan: port 3(wlan0) entered forwarding state [ 52.645008] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 52.645364] br-lan: port 2(wlan1) entered blocking state [ 52.709835] br-lan: port 2(wlan1) entered forwarding state
Notes
Space for additional notes, links to forum threads or other resources.
- ...