Arcadyan ARV7510PW

The ARV7510PW is an ADSL2+ router with 802.11n wireless commonly obtained via the Finnish ISP Elisa (Elisa kotiboksi / Elisa kotiboxi). It is a rebranded Bewan Ibox. There is also another similar device based on Arcadyan ARV4510PW. The only difference seems to be the wireless mini-PCI card, which in ARV4510PW is only 802.11bg capable (Atheros AR241x). From outside these can be distinguished by the antenna color: ARV7510PW has a black antenna, ARV4510PW white. There exists also an all-black ARV4510PW, the Wippies Homebox. Finally, there are also ARV4510PW models where the wireless chip is not on a mini-PCI card, but rather soldered directly on the main board. The wireless in these models is not (yet) supported due to the missing EEPROM.

FIXME Please explain the differences / similarities of ARV7510PW and ARV7510PW22.

OpenWrt runs almost perfectly with some additional patches below. WiFi works, but has been reported to crash randomly depending on mostly unknown factors, your mileage may vary. ADSL also works, but may have unspecified problems (such as high memory usage).

SSH_root connection to Elisa box is available using this tool: (Use cable, dhcp to perform). Installation may require a JTAG serial connection. The router is practically unbrickable by virtue of the UART boot capability, if bootloader is on state.

Missing features

  • Third USB port working as USB ethernet is not functional due to missing drivers.
Architecture: MIPS
Target: lantiq
Vendor: Arcadyan
Bootloader: brnboot
System-On-Chip: Infineon/Lantiq Xway Danube (PSB 50702 E V1.3 or V1.4)
CPU Speed: 333 MHz
Flash chip: Intel JS28F128J3D-75
Flash size: 16 MiB
RAM chip: PSC A3S56D40ETP
RAM size: 32 MiB
USB: 2x USB 2.0 standard A + 1x USB 2.0 standard B
ADSL: ADSL (G.992.1 & T1.413, V2), ADSL2 (G.992.3), ADSL2+ (G.992.5)
Ethernet: Infineon ADM6996I, 4x LAN 100 Mbps
Wireless: Ralink RT2860T, 802.11n 300 Mbps, 2.4 GHz, 2 antennas
Phone: 2x RJ11
Serial: yes (with header)
JTAG: yes (no header)
Buttons: power switch, WiFi button, reset button

Suitable U-Boot can be found under Boot Loaders → uboot-lantiq-arv7510pw_nor/ram (works also with ARV4510PW). NOR-version will be installed to flash, RAM-version can be used with the UART boot option.

Following patches for Barrier Breaker (14.07) are needed:

Pre-built Barrier Breaker (14.07) image (includes luci and kmod-ath5k):

Pre-built U-Boot:

Official OpenWrt 14.07 images for lantiq xway do not work due to missing patch for disabling buffered writes. Trunk and Chaos Calmer (15.05) should work without extra patches since r44451.

On the official build of Chaos Calmer (15.05) network does not work by default:

root@OpenWrt:/# /etc/init.d/network restart
[  226.056000] br-lan: port 1(eth0.1) entered disabled state
[  226.072000] device eth0.1 left promiscuous mode
[  226.076000] device eth0 left promiscuous mode
[  226.080000] br-lan: port 1(eth0.1) entered disabled state
[  226.088000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Failed to connect to the switch. Use the "list" command to see which switches are available.
root@OpenWrt:/# [  231.800000] device eth0.1 entered promiscuous mode
[  231.804000] device eth0 entered promiscuous mode
[  231.812000] br-lan: port 1(eth0.1) entered forwarding state
[  231.816000] br-lan: port 1(eth0.1) entered forwarding state
[  233.820000] br-lan: port 1(eth0.1) entered forwarding state

To get network and USB to work you need to apply the following patches:

The latest trunk (Designated Driver r49395) compiles with the two patches listed above (with a minor adjustment to the irq patch). It seems to work rather well, although wifi on rare occasions resets briefly and firmware updates via LuCi crash. Otherwise, it is quite stable. The kernel is now from the 4.4 series. Here is a compiled image:

Follow the installation procedure below on this webpage to install the firmware. You will need the latest uBoot to install this firmware.

To compile r49395 correctly, you will need the 0400-fix-IO_SPACE_LIMIT-constant.patch provided above, plus a slightly modified version of 0401-fix-irq-chip-for-exins.patch, which is provided here:

Many thanks to the author of these patches who originally provided them above!

To compile your own firmware, set up an OpenWrt compile system as described elsewhere on the site for trunk and place the two patches into the directory target/linux/lantiq/patches-4.4/. Compile per instructions for building a firmware image. The resulting firmware will be found in the directory bin/lantiq/ (with the name openwrt-lantiq-xway-ARV4510PW-squashfs-sysupgrade.bin). It can be installed in the same manner as the squashfs.image as outlined below.

UPDATE: The LEDE project at has improved support for this device. The latest patches are already included and the firmware compiles without error. All functions of the device appear to work well and the latest 4.4 kernels are tracked quite promptly.

Older versions of the original firmware have a security exploit, which gives access to a flat text version of the router settings.

Run this python3 script to check if the router is vulnerable

import urllib.request
req = urllib.request.Request('')
req.add_header('Referer', '')
r = urllib.request.urlopen(req)
f = open('router.txt', 'wb')

If it doesn't produce any errors:

  1. Open the produced router.txt with your favourite editor.
  2. Set UserTable_1_Unix_Enable to 1
  3. Set UserTable_1_Unix_Password to $1$xopJA6FB$fJnqEswAbH0SDg.sPLUKf.
  4. Set Services_Telnet_Enable to 1
  5. Save the file and upload as you would with a standard backup

Do not continue if you aren't willing or able to use UART method:

  1. Copy openwrt-lantiq-arv7510pw_nor-u-boot.img and openwrt-lantiq-xway-ARV4510PW-squashfs.image onto a fat32 usb drive
  2. Plug the usb drive into the router
  3. telnet into the router as root with password as password
  4. cd into the usb drive (can be found with mount)
  5. umount /dev/rd/0
  6. dd if=/dev/mtd/0 bs=1 of=routerBackup.bin
  7. dd if=openwrt-lantiq-arv7510pw_nor-u-boot.img bs=1 of=/dev/mtdblock/0
  8. dd if=openwrt-lantiq-xway-ARV4510PW-squashfs.image bs=1 seek=393216 of=/dev/mtdblock/0
  9. wait a while
  10. reboot

After installation you should set your MAC-addresses with the commands

uci set network.lan.macaddr=xx:xx:xx:xx:xx:xx
uci set network.wan.macaddr=xx:xx:xx:xx:xx:xx
uci commit

and reboot.

The installation procedure in short:

  1. Short the UART boot pins and power on the router
  2. Upload a special U-Boot RAM image using a serial cable
  3. Use U-Boot to erase the flash and install U-Boot to flash
  4. Power off the router, unshort the UART boot pins, and power on again
  5. Use the installed U-Boot to install OpenWrt to flash


You need a RS232-to-TTL cable connected to the serial header shown in the picture below. Short the UART boot pins with two jumper caps. If the router misbehaves, remove the Vcc-cable, but leave ground attached.

Start TFTP server on your computer and copy openwrt-lantiq-arv7510pw_nor-u-boot.img and openwrt-lantiq-xway-ARV4510PW-squashfs.image to the TFTP server root. Connect your computer to the router with an ethernet cable and configure the IP address to, netmask

Loading U-Boot

Use baud rate 115200, 8-N-1, no flow control as the serial connection parameters.

Power on the router. You should see the following on the serial output.

ROM VER: 1.0.3
CFG 04

The router now waits for bootloader code. Send openwrt-lantiq-arv7510pw_ram-u-boot.asc as raw ascii to the router. U-Boot should start. Press any key to stop autoboot when prompted.

At this point you can make a backup of the original firmware using md.l 0xb0000000 0x1000000 and logging the output (takes roughly 2 hours).

To flash u-boot now, run the following in the bootloader's shell

# remove flash protection
protect off all
# erase all flash (also the bootloader)
erase all
# set bootloader ip-address to connect from
setenv ipaddr
# Set the ip-address to load the bootloader from
setenv serverip
# Ethernet address can be found from the sticker on top of the switch ports
setenv ethaddr 00:01:02:03:04:05
# Download bootloader to ram
tftp 0x80700000 openwrt-lantiq-arv7510pw_nor-u-boot.img
# Write bootloader to permanent flash memory
cp.b 0x80700000 0xb0000000 ${filesize}

Loading OpenWrt

Power on the router. The U-Boot installed in the previous step should start. Press any key to stop autoboot. Run the following to now load openwrt firmware:

setenv ipaddr
setenv serverip
setenv ethaddr 00:01:02:03:04:05
# Save environment settings to the bootloader's memory
# Download openwrt to ram
tftp 0x80700000 openwrt-lantiq-xway-ARV4510PW-squashfs.image
# Write openwrt to permanent flash memory
cp.b 0x80700000 0xb0060000 ${filesize}
# reboot router to boot to openwrt

Watch as U-Boot loads OpenWrt and proceed to configure it to your liking!

The router is usable after it finishes cleanup:

[  127.012000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[  127.020000] jffs2_build_filesystem(): unlocking the mtd device... done.
[  157.432000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[  206.468000] jffs2: notice: (1273) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -

To reflash a new version without erasing bootloader or bootloader settings (this is only for subsequent debricking of the router):

tftp 0x80700000 openwrt-lantiq-xway-ARV4510PW-squashfs.image
erase 0xb0060000 +${filesize}
cp.b 0x80700000 0xb0060000 ${filesize}
bootm 0xb0060000

The internal switch port numbering is opposite from the one printed on the box. Port 0 corresponds to the port labeled as “Port 4/Uplink”. Port 5 is connected to the CPU. If you wish to use the uplink port as WAN with IP address obtained by DHCP, you need to modify the network configuration as follows

uci set network.@switch_vlan[0].ports="1 2 3 5t"
uci add network switch_vlan
uci set network.@switch_vlan[1].device=switch0
uci set network.@switch_vlan[1].vlan=2
uci set network.@switch_vlan[1].ports="0 5t"
uci set network.wan.ifname=eth0.2
uci set network.wan.proto=dhcp
uci delete network.wan.username
uci delete network.wan.password
uci delete network.wan.ipv6
uci commit

The power supply of the USB ports may be inadequate for LTE sticks or other USB devices demanding high currents. Replacing the 47 µF electrolytic capacitors connected to pin 1 of the USB ports with 1000 µF/10 V low-ESR models will allow the router to handle high current pulses. Another option is to use a powered USB hub.

The usb-ethernet port (standard B type USB, USB2) is unpowered and not usable at the moment. It requires usb-gadget support to function as the usb-ethernet port. You would at least need to enable the following in kernel configuration and then modprobe g_ether

<M> Support for USB Gadgets 
<M>   Ethernet Gadget (with CDC Ethernet support)
[*]     RNDIS support (EXPERIMENTAL)

Some units generate spurious button presses, which lead to reboots or other problems. Enabling the Schmitt-trigger may help. This can be achieved by modifying the U-Boot boot command and saving the modification to flash:

setenv bootcmd 'mw.l 0xbe100b28 0x4008; bootm ${kernel_addr}'

Units with V1.4 of the Danube SoC may become unstable when the ADSL status is queried. In this case it is recommended to edit the file /usr/lib/lua/luci/view/admin_status/index.htm and change the reference to /etc/init.d/dsl_control to point to a non-existent file.

The VoIP ports seem to be working in the latest OpenWrt release. Interesting packages for potential VoIP support include:

The original bootloader (brnboot) is completely locked. There is no access to the administration menu typically found on other brnboot devices.

By default the device runs Linux 2.6.16. The serial console does not accept any input, and there is no telnet or ssh available. The web interface of the original firmware is extremely limited, and the configuration is done remotely by ISP via TR-069. There is a local firmware update page, but it doesn't accept third party firmwares.

The original firmware is not encrypted or obfuscated in any way, contrary to many other Arcadyan devices. Therefore it might be easy to produce acceptably packaged firmwares. Adding a header like in the original firmware might be enough. For people with MIPS (dis)assembly skills, here is the cgi script and the firmware flash tool extracted from the original firmware.

The ART partition contains the squashfs file system of the actual firmware. Partition Config contains a writable ext2 file system, where configuration is kept. During firmware update OldFirmware is replaced and marked Firmware, and Firmware becomes OldFirmware.

Original flash layout
Layer 0 Flash 16384 KiB
Layer 1 Loader 128KiB Config 128 KiB OldFirmware 8064 KiB Firmware 8064 KiB
Layer 2 Header + old kernel 880 KiB Old ART 6808 KiB Footer 376 KiB Header + kernel 880 KiB ART 6808 KiB Footer 376 KiB
File system ext2 squashfs squashfs

Serial output from booting original firmware:

ROM VER: 1.0.3 CFG 01 Read EEPROMX X ROM VER: 1.0.3 CFG 01 Read EEPROMX X _ | |__ _____ ____ _ _ __ | '_ \ / _ \ \ /\ / / _` | '_ \ | |_) | __/\ V V / (_| | | | | |_.__/ \___| \_/\_/ \__,_|_| |_| Portions Copyright (c) 2005-2008 bewan systems Parameters: Product : A50804 Product family : A50800 Flash size : 1000000 DRAM size : 2000000 Ethernet : MII LAN MAC address : xx:xx:xx:xx:xx:xx WAN MAC address : xx:xx:xx:xx:xx:xx Dual bank boot : yes Reset : no Pairing : no Serial number : xxxxxxxxxxxxxxx WEP key : xxxxxxxxxxxxx Loader version : 23085 Capabilities : 80000001 Found valid bootable partition 0: Copyright (c) 2006-2008 BeWAN Systems Arcadyan ARV4510PW-A-LF-L3 - Elisa A50804 2009-05-07-14:11:30 A50804-Elisa11-23085.bin Found valid bootable partition 1: Copyright (c) 2006-2008 BeWAN Systems Arcadyan ARV4510PW-A-LF-L3 - Elisa A50804 2009-08-28-16:19:08 A50804-Elisa12-25535.bin Booting from partition 1 in flash. Loading: Linux Kernel Image Load address = 80000000 Uncompressing Linux..................... done, booting the kernel. start addr = 802F1000 memsize=31 TODO: chip version Linux version 2.6.16bewan ( (gcc version 3.3.4) #1 Reserving memory for CP1 @0xa1f00000 memsize=31 CPU revision is: 00019641 PCI: Probing PCI hardware on host bus 0. Board with an external oscillator Determined physical RAM map: memory: 01f00000 @ 00000000 (usable) User-defined physical RAM map: memory: 01f00000 @ 00000000 (usable) Built 1 zonelists Kernel command line: nofpu console=ttyS0,115200n1 bewan_boot=flash1 bewan_fs_addr=0x8fc000 bewan_fs_size=0x6a6000 mem=31M Primary instruction cache 16kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled PID hash table entries: 128 (order: 7, 2048 bytes) mips_hpt_frequency:166666667 r4k_offset: 00196e6a(1666666) Using 166.667 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 27648k/31744k available (2517k kernel code, 4096k reserved, 491k data, 160k init, 0k highmem) Mount-cache hash table entries: 512 Checking for 'wait' instruction... available. NET: Registered protocol family 16 TC classifier action (bugs to cc DANUBE MIPS24KEc MPS mailbox driver, Version 1.1.0 (c) Copyright 2006, Infineon Technologies AG IFX_MPS: using proc fs squashfs: version 3.0 (2006/03/15) Phillip Lougher Squashfs 2.2 with LZMA support devfs: 2004-01-31 Richard Gooch ( devfs: boot_options: 0x1 Initializing Cryptographic API io scheduler noop registered (default) Danube MEI version:1.00.09 Danube MEI MIB version:0.90.04 Danube Port Settings Danube Port Initialization cgu: misc_register on minor = 63 gptu: totally 6 16-bit timers/counters gptu: misc_register on minor 62 gptu: succeeded to request irq 118 gptu: succeeded to request irq 119 gptu: succeeded to request irq 120 gptu: succeeded to request irq 121 gptu: succeeded to request irq 122 gptu: succeeded to request irq 123 ttyS0 at MMIO 0xbe100c00 (irq = 9) is a DANUBEASC ttyS1 at MMIO 0xbe100400 (irq = 2) is a DANUBEASC RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: loaded (max 8 devices) PPP generic driver version 2.4.2 NET: Registered protocol family 24 danube ETOP driver loaded! ppe: ATM init succeeded (firmware version Danube IAD flash device: 0x1000000 at 0xb0000000 Danube IAD FLASH: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 cfi_cmdset_0001: Erase suspend on write enabled Creating 5 MTD partitions on "Danube IAD FLASH": 0x00000000-0x01000000 : "Flash" 0x00000000-0x00020000 : "Loader" 0x00020000-0x00040000 : "Config" 0x00820000-0x01000000 : "Firmware" 0x00040000-0x00820000 : "OldFirmware" bootpart=2 Creating 1 MTD partitions on "Danube IAD FLASH": 0x008fc000-0x00fa2000 : "ART" rootdev = 31,5 dwc_otg: version 2.40a 10-APR-2006 usb0: Ethernet Gadget, version: Equinox 2004 usb0: using dwc_otg_pcd, OUT ep2 IN ep1 STATUS ep3 usb0: MAC 76:c1:d0:35:08:a9 usb0: HOST MAC 46:67:b2:31:f5:5c usb0: RNDIS ready LED and Buttons driver: v2.6.0 GACT probability on Mirror/redirect action on netem: version 1.2 u32 classifier Perfomance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. NET: Registered protocol family 2 IP route cache hash table entries: 256 (order: -2, 1024 bytes) TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered ip_conntrack version 2.4 (248 buckets, 1984 max) - 232 bytes per conntrack DS max rate = 0 kbps US max rate = 0 kbps DS payload rate = 0 kbps US payload rate = 0 kbps Local CRC = 0 Remote CRC = 0 ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <> All bugs added by David S. Miller <> Ethernet Multiplexer Support v1.0 Christophe Piel (c) 2006 BeWAN systems VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memoryinit started: BusyBox v1.00 multi-call binary Starting pid 130, console /dev/tts/0: '/etc/rc' Algorithmics/MIPS FPU Emulator v1.5 Software Watchdog Timer: 0.05, timer margin: 120 sec. Mon Jan 1 00:00:00 UTC 2007 _ | |__ _____ ____ _ _ __ | '_ \ / _ \ \ /\ / / _` | '_ \ | |_) | __/\ V V / (_| | | | | |_.__/ \___| \_/\_/ \__,_|_| |_| IFX TAPI, version, (c) 2007 Infineon Technologies IFX VMMC device driver, version, (c) 2007 Infineon Technologies AG <6>usbcore: registered new driver usbfs usbcore: registered new driver hub SCSI subsystem initialized Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. PCI: Enabling device 0000:00:0f.2 (0000 -> 0002) plat_dev_init(803e8400) ehci_hcd 0000:00:0f.2: EHCI Host Controller ehci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0f.2: irq 26, io mem 0x18010000 ehci_hcd 0000:00:0f.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected USB Universal Host Controller Interface driver v2.3 PCI: Enabling device 0000:00:0f.0 (0000 -> 0001) plat_dev_init(803e8c00) uhci_hcd 0000:00:0f.0: UHCI Host Controller uhci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:0f.0: irq 26, io base 0x1ae00000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device 0000:00:0f.1 (0000 -> 0001) plat_dev_init(803e8800) uhci_hcd 0000:00:0f.1: UHCI Host Controller uhci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:0f.1: irq 26, io base 0x1ae00020 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected Linux video capture interface: v1.00 pwc: Philips webcam module version 10.0.12-rc1 loaded. pwc: Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840. pwc: Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30, pwc: the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100. usbcore: registered new driver Philips webcam usbcore: registered new driver gspca ../user/gspca/gspca_core.c: gspca driver 01.00.20 registered build router.conf from /etc/flash/router.diff /etc/init.d/syslog start /etc/eom.d/update-config /etc/init.d/dsl start modprobe: module ctlmeth not found. modprobe: failed to load module ctlmeth /etc/init.d/interface start LANEthernetInterface 1 /etc/init.d/switch start 1 /etc/init.d/phy stop 1 1 using the specified MII index 19. power down... /etc/init.d/phy stop 1 2 using the specified MII index 18. power down... /etc/init.d/phy stop 1 3 using the specified MII index 17. power down... /etc/init.d/phy stop 1 4 using the specified MII index 16. power down... /etc/init.d/switchvlan start 1 vlanTAGctl : disabling all hardware VLANs vlanTAGctl : creating vlan VID=0x1 with UNTAGGED=0xE TAGGED=0x30 INDEX=0 vlanTAGctl : creating vlan VID=0x2 with UNTAGGED=0x1 TAGGED=0x30 INDEX=1 modprobe: module ctlmusb not found. modprobe: failed to load module ctlmusb /etc/init.d/interface start LANUSBInterface 1 wireless config : ralink 0060 18140601 5f 18000000 00000000 00000000 00000000 00000000 00000000 00000000 00010000 00000000 00000000 00000000 00000000 00000000 00000000 /etc/init.d/wifi.d/wifi start 1 There is no MACADDR for ra0 WiFi card MAC address rewritter Not in the good Hi range address Exit rt2860ap: module license 'unspecified' taints kernel. PCI: Enabling device 0000:00:0c.0 (0000 -> 0002) plat_dev_init(81055000) === pAd = c0223000, size = 485664 === <-- RTMPAllocAdapterBlock, Status=0 /etc/init.d/wifi.d/easyp nothing RX DESC a1ba1000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l Main bssid = xx:xx:xx:xx:xx:xx The UUID Hex string is:bc329e001dd811b28601000cc37aac58 The UUID ASCII string is:bc329e00-1dd8-11b2-8601-000cc37aac58! <==== RTMPInitialize, Status=0 0x1300 = 00064380 expr: syntax error 0060 18140601 5f 18000000 00000000 00000000 00000000 00000000 00000000 00000000 00010000 00000000 00000000 00000000 00000000 00000000 00000000 rt2860 /etc/init.d/wifi.d/wifi nothing 2 0060 18140601 5f 18000000 00000000 00000000 00000000 00000000 00000000 00000000 00010000 00000000 00000000 00000000 00000000 00000000 00000000 rt2860 /etc/init.d/wifi.d/wifi nothing 3 modprobe: module ctlmatm not found. modprobe: failed to load module ctlmatm /etc/init.d/interface nothing ATMEthernetInterface 1 /etc/init.d/interface nothing ATMEthernetInterface 2 /etc/init.d/interface nothing ATMEthernetInterface 3 /etc/init.d/interface nothing ATMEthernetInterface 4 /etc/init.d/interface nothing ATMEthernetInterface 5 /etc/init.d/autodslam start auto-stop /etc/init.d/lan start 1 expr: syntax error expr: syntax error /etc/init.d/lanif start 1 all /etc/init.d/lanintf start lan1 eth0.1 eth0.1: dev_set_promiscuity(master, 1) device eth0 entered promiscuous mode device eth0.1 entered promiscuous mode /etc/init.d/lanintf start lan1 usb0 device usb0 entered promiscuous mode /etc/init.d/lanintf start lan1 ra0 device ra0 entered promiscuous mode /etc/init.d/shaping nothing /etc/init.d/lanip start 1 /etc/config.default/ip-up-dhcp lan1 lan1: port 3(ra0) entering listening state lan1: port 1(eth0.1) entering listening state /etc/init.d/host start /etc/init.d/igmp start expr: syntax error expr: syntax error /etc/init.d/inittab /etc/init.d/ipsec restart all /etc/init.d/landhcp start 1 /etc/init.d/ipsec nothing 1 /etc/init.d/wifi.d/lanacl start 1 /etc/init.d/passthrough start 1 /etc/init.d/lan start 2 /etc/init.d/lanif start 2 all /etc/init.d/racoon stop /etc/init.d/lanintf nothing lan2 ra1 /etc/init.d/shaping nothing /etc/init.d/lanip start 2 /etc/config.default/ip-up-dhcp lan2 /etc/init.d/host start /etc/init.d/igmp start /etc/init.d/inittab /etc/init.d/ipsec restart all /etc/init.d/ipsec nothing 1 /etc/init.d/landhcp start 2 /etc/init.d/racoon stop /etc/init.d/wifi.d/lanacl start 2 /etc/init.d/passthrough nothing 2 /etc/init.d/lan start 3 /etc/init.d/lanif start 3 all /etc/init.d/lanintf nothing lan3 ra2 /etc/init.d/shaping nothing /etc/init.d/lanip start 3 /etc/config.default/ip-up-dhcp lan3 /etc/init.d/host start /etc/init.d/igmp start /etc/init.d/inittab /etc/init.d/ipsec restart all /etc/init.d/ipsec nothing 1 /etc/init.d/landhcp start 3 /etc/init.d/wifi.d/lanacl start 3 lan1: port 3(ra0) entering learning state lan1: port 1(eth0.1) entering learning state /etc/init.d/racoon stop /etc/init.d/passthrough nothing 3 /etc/init.d/lan nothing 4 /etc/init.d/users start /etc/init.d/unix start /etc/init.d/unixusers start 1 /etc/init.d/unixusers start 2 /etc/init.d/samba start /etc/init.d/pureftpd start /etc/init.d/webusers nothing /etc/init.d/unixadmin start /etc/init.d/time start /etc/init.d/mdns nothing /etc/init.d/rmthttp start /etc/init.d/wan start 1 /etc/init.d/interface start WANConnectionDevice 1 eth0.2: dev_set_promiscuity(master, 1) device eth0.2 entered promiscuous mode /etc/init.d/wannet start 1 /etc/init.d/wanbr nothing 1 /etc/init.d/wanip start 1 /etc/init.d/wanppp nothing 1 /etc/init.d/firewall start 1 /etc/init.d/ports start 1 /etc/init.d/wan nothing 2 /etc/init.d/wan nothing 3 /etc/init.d/wan nothing 4 /etc/init.d/qos start all /etc/init.d/shaping nothing /etc/init.d/dhcp start all /etc/init.d/dhcpd nothing all /etc/init.d/dhcrelay nothing all /etc/init.d/hbrdhcp start all /etc/init.d/dnsmasq start all /etc/init.d/dnsmasq start all /etc/init.d/pppd start all /etc/init.d/dhclient start all /etc/init.d/pptp stop /etc/init.d/openl2tp stop /etc/init.d/ipsec all /etc/init.d/fwrules start lan1: topology change detected, propagating lan1: port 3(ra0) entering forwarding state lan1: topology change detected, propagating lan1: port 1(eth0.1) entering forwarding state /etc/init.d/iptables start /etc/init.d/ebtables start /etc/init.d/routes start /etc/init.d/upnp start /etc/init.d/dyndns nothing /etc/init.d/inittab expr: syntax error /etc/init.d/stunnel start expr: syntax error /etc/init.d/phy start 1 1 using the specified MII index 19. resetting the transceiver... restarting autonegotiation... /etc/init.d/phy start 1 2 using the specified MII index 18. resetting the transceiver... restarting autonegotiation... /etc/init.d/phy start 1 3 using the specified MII index 17. resetting the transceiver... restarting autonegotiation... /etc/init.d/phy start 1 4 using the specified MII index 16. resetting the transceiver... restarting autonegotiation... /etc/init.d/inittab rc completed Starting pid 2050, console /dev/null: '/sbin/syslogd' Starting pid 2051, console /dev/null: '/sbin/klogd' Starting pid 2052, console /dev/null: '/bin/dhclient' Starting pid 2053, console /dev/null: '/bin/dnsmasq-2' Starting pid 2054, console /dev/null: '/sbin/igmpproxyd' Starting pid 2055, console /dev/console: '/bin/resetd' Starting pid 2056, console /dev/null: '/bin/upnpd' Starting pid 2057, console /dev/console: '/bin/wdgd' Software Watchdog Timer: set margin to 40 sec. /etc/init.d/upgd nothing /etc/init.d/inetd start /etc/init.d/http start /etc/init.d/htpwd start /etc/init.d/tr069 start /etc/init.d/usbdevices usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for airprime usbcore: registered new driver airprime /etc/init.d/voip-asterisk nothing /etc/init.d/bluetooth nothing /etc/init.d/host start /etc/init.d/userscreatedir start /etc/init.d/usersdir start 1 /etc/init.d/usersdir start 2 /etc/init.d/sambaserver refresh /etc/init.d/upnpav nothing /etc/init.d/pureftpdserver start /etc/init.d/obexpush nothing4 /etc/init.d/web nothing /etc/init.d/printer start /etc/init.d/webcam start usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver /etc/init.d/inittab Reloading /etc/inittab Starting pid 2381, console /dev/console: '/bin/thttpd' Starting pid 2382, console /dev/console: '/bin/tr069' Starting pid 2383, console /dev/null: '/bin/lighttpd'

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2018/04/21 10:30
  • by tmomas