TP-Link xx230v v1

EN7523DRAMC V0.2 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x1b, OCDN:0x1e, ODTP:0xa, ODTN:0xa DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=256MB U-Boot 2014.04-rc1 (Mar 19 2024 - 09:12:08) DRAM: 240 MiB EN7529CT Now running in RAM - U-Boot at: 8edff000 spi_nand_probe: mfr_id=0xc8, dev_id=0x1 Using Flash ECC. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_F50L1G41LB, Flash Size=0x8000000 bmt pool size: 81 BMT & BBT Init Success In: serial Out: serial Err: serial CPU0: found redistributor 0 region 0:8ee3d988 Net: ecnt_eth Uip activated use flash mac: 8C:90:2D: 6:A9:48 Not found TC Phy Not found TC Phy Not found TC Phy Not found TC Phy [ CPEinit ] 465: CPE init [ cp_initCommProto ] 277: g_commProtoConfig.myMac: 8c:90:2d:06:a9:48 [ os_initCPEInfo ] 297: hw ver: XX230v v1.0 00000000 [ os_initCPEInfo ] 298: sw ver: 0.12.0 3.0.0 v6066 [ os_initCPEInfo ] 305: sn: 2248478002084 [ os_initCPEInfo ] 308: pin: 10289273 [ os_initCPEInfo ] 315: endian: 0 [ os_initCPEInfo ] 318: acFlag: 0 [ CPEinit ] 489: CPE is idle Hit any key to stop autoboot: 0 Prepare to boot image1 bootm flag=0, states=70f ## Loading kernel from FIT Image at 81800200 ... Using 'conf@1' configuration Trying 'kernel@1' kernel subimage Description: ECONET Linux kernel Type: Kernel Image Compression: lzma compressed Data Start: 0x818022a4 Data Size: 4730117 Bytes = 4.5 MiB Architecture: ARM OS: Linux Load Address: 0x80088000 Entry Point: 0x80088000 Hash algo: sha1 Hash value: 71831c68c18b0d0ebe74b42ed8133ee86ccf6ce1 ## Loading fdt from FIT Image at 81800200 ... Using 'conf@1' configuration Trying 'fdt@1' fdt subimage Description: ECONET Flattened Device Tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x818002fc Data Size: 7913 Bytes = 7.7 KiB Architecture: ARM Hash algo: sha1 Hash value: 73fbebcf3dfc0e0007752bdeff8c7c0f35611f24 Booting using the fdt blob at 0x818002fc Uncompressing Kernel Image ... OK Loading Device Tree to 8cdf2000, end 8cdf6ee8 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 4.4.115 (compile@342f0d6254c6) (gcc version 4.9.3 (Buildroot 2015.08.1-gd814875) ) #1 SMP Tue Mar 19 09:18:53 UTC 2024 CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: econet,en7523 bootconsole [uart0] enabled Memory policy: Data cache writealloc psci: probing for conduit method from DT. psci: PSCIv1.1 detected in firmware. psci: Using standard PSCI v0.2 function IDs psci: MIGRATE_INFO_TYPE not supported. [c08472b8]npu_pkt_buf_addr=8dff37c0:8dff37c0 npu_pkt_buffer memblock_alloc:8dff37c0,buf_size=1600000 PERCPU: Embedded 12 pages/cpu @cdfd9000 s18048 r8192 d22912 u49152 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64704 Kernel command line: sdram_conf=0x00108893 vendor_name=ECONET Technologies Corp. product_name=xPON ONU ethaddr=8C:90:2D:06:A9:48 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 username=telecomadmin password=nE7jA%5m dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=33 root=/dev/mtdblock8 ro console=ttyS0,115200n8 earlycon bootflag=0 serdes_sel=0 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 212276K/260864K available (8124K kernel code, 3998K rwdata, 2400K rodata, 240K init, 666K bss, 48588K reserved, 0K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbec00000 - 0xbfe00000 ( 18 MB) .text : 0xc0088000 - 0xc0acf450 (10526 kB) .init : 0xc0ad0000 - 0xc0b0c000 ( 240 kB) .data : 0xc0b0c000 - 0xc0ef3980 (3999 kB) .bss : 0xc0ef6000 - 0xc0f9c8e0 ( 667 kB) Hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. NR_IRQS:64 nr_irqs:64 64 CPU0: found redistributor 0 region 0:0x09080000 Architected cp15 timer(s) running at 25.00MHz (virt). clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns Switching to timer-based delay loop, resolution 40ns console [ttyS0] enabled console [ttyS0] enabled bootconsole [uart0] disabled bootconsole [uart0] disabled Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys debug CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x80088280 - 0x800882d8 CPU1: found redistributor 1 region 0:0x090a0000 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (100.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 512 (order: 3, 32768 bytes) NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. hw-breakpoint: maximum watchpoint size is 8 bytes. l2c_sram_size:0x0 Initializing Ecnt Event Netlink Socket Initializing Econet Event Netlink Socket nl_sk = cd579800 ecnt-hsdma 1fa01800.dma-controller: Econet HSDMA driver registered SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb clocksource: Switched to clocksource arch_sys_counter NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available sgmii probe init start sgmii:int_name: sgmii_pcie0 sgmii:int_id: 0 sgmii:int_register: inin! sgmii:sgmii->pcs1_base= d087c100 sgmii:sgmii->pcs2_base= d087ea00 sgmii:sgmii->an_base= d0944000 sgmii:sgmii->ra_base= d0946600 sgmii:sgmii->phya_base= d0948c00 sgmii:int_register: exit! sgmii: int_init called sgmii:cmd_wo:reg_t=d087ea20, val=0 sgmii: sync_int exit sgmii probe init exit sgmii probe init start sgmii:int_name: sgmii_pcie1 sgmii:int_id: 1 sgmii:int_register: inin! sgmii:sgmii->pcs1_base= d094a100 sgmii:sgmii->pcs2_base= d094ca00 sgmii:sgmii->an_base= d094e000 sgmii:sgmii->ra_base= d0950600 sgmii:sgmii->phya_base= d0952c00 sgmii:int_register: exit! sgmii: int_init called sgmii:cmd_wo:reg_t=d094ca20, val=0 sgmii: sync_int exit sgmii probe init exit sgmii probe init start sgmii:int_name: sgmii_usb0 sgmii:int_id: 2 sgmii:int_register: inin! sgmii:sgmii->pcs1_base= d0954100 sgmii:sgmii->pcs2_base= d0956a00 sgmii:sgmii->an_base= d0958000 sgmii:sgmii->ra_base= d095a600 sgmii:sgmii->phya_base= d095cc00 sgmii:int_register: exit! sgmii: int_init called sgmii:cmd_wo:reg_t=d0956a20, val=0 sgmii: sync_int exit sgmii probe init exit TC3162 hardware watchdog module loaded. irq-0: 109 irq-1: 110 [i2c] ecnt_i2c_drv_probe [crypto_k] res->name:/crypto_k@1fb70000 [crypto_k] res->start:0x1fb70000 === [crypto_k] res->end:0x1fb70803 === [crypto_k] ecnt_crypto_k->base:0xd09dc000 [trng] ecnt_trng_drv_probe test_uc:d0826000 test_c:cd4c0000 cpu_top->base:d09e6800 [apb_timer] ecnt_timer_drv_probe [timer] ecnt_timer->irq: 80 [timer] res->name:/apb_timer1@1fbf0100 i2c_slave init(ecnt_i2c_slave_drv_probe) done [i2s] ecnt_i2s_drv_probe 7523 Thermal Sensor address probe done squashfs: version 4.0 (2009/01/31) Phillip Lougher exFAT: Version 1.2.9 jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.23) io scheduler noop registered (default) PCIe driver version: 7523.0.20210201 PCIe ref clk init. ===EN7523 PCIe init mtk-pcie 1fa91000.pcie: Port0 link down mtk-pcie 1fa91000.pcie: pcie rc 1 linkup success ===============PCIe check===tmp_reg=========81014c3=========== mtk-pcie 1fa91000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] pci_bus 0000:00: root bus resource [bus 00-ff] PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus1: Fast back to back transfers enabled PCI: bus2: Fast back to back transfers disabled pci 0000:00:01.0: BAR 8: assigned [mem 0x20000000-0x201fffff] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:02:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref] pci 0000:02:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref] pci 0000:02:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x20000000-0x201fffff] mt7512_pcie_fixup: 0x2438 = 20000015 mt7512_pcie_rc1_retrain: 80 = 0145dc12 80 = 01608c12 RC1 Link Traing Result: 10120008 ===========RC1 set conf space INTx============= ttyS0 at I/O 0xbfbf0000 (irq = 95, base_baud = 7200) is a TC3162 ECNT ring buffer init success brd: module loaded SPI Flash Init Start Found no SPI flash device IS_SPIFLASH=0x0, IS_NANDFLASH=0x1, (0xBFA10114)=0x6) Set SPI Clock to 50 Mhz spi_nand_probe: mfr_id=0xc8, dev_id=0x1 Using Flash ECC. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_F50L1G41LB, Flash Size=0x8000000 spi nand flash tc3162: flash device 0x02000000 at 0x00000000 EN7512 mtd init: spi nand probe enter [spi_nand_setup] : Enter nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x01 nand: Unknown _SPI_NAND_DEVICE_ID_F50L1G41LB nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 nand_scan_ident ok [spi_nand_setup]: chip size = 0x8000000, erase_shift=0x11 bmt pool size: 81 BMT & BBT Init Success Creating 11 MTD partitions on "EN7512-SPI_NAND": 0x000000000000-0x000004000000 : "whole" 0x000000000000-0x000000080000 : "boot" 0x000000080000-0x0000000a0000 : "romfile" 0x0000000a0000-0x0000001a0000 : "misc" 0x0000001a0000-0x0000009a0000 : "kernel" 0x0000009a0000-0x000002000000 : "rootfs" 0x0000001a0000-0x000002000000 : "firmware" 0x000002000000-0x000002800000 : "kernel_slave" 0x000002800000-0x000003e60000 : "rootfs_slave" 0x000002000000-0x000003e60000 : "firmware_slave" 0x000003fe0000-0x000004000000 : "reserve" rootfs PPP generic driver version 2.4.5 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register rtpci pci 0000:00:01.0: enabling device (0140 -> 0142) rtpci 0000:02:00.0: enabling device (0140 -> 0142) === pAd = d3201000, size = 9391104 === <-- RTMPAllocAdapterBlock, Status=0 PCI CSRBaseAddress =0xd3100000, csr_addr=0xd3100000! RTMPInitPCIeDevice():device_id=0x7915 mt7915_init()--> Use the default iPAiLNA bin image! <--mt7915_init() wdev_init(caller:RTMP_COM_IoctlHandle+0x1190/0x19d8), wdev(0) !!HIF_RX_EVENT Only !!HIF_RX_EVENT Only !!HIF_RX_EVENT Only <-- pci_alloc_tx_rx_ring_mem, Status=0 Error: host_notify_npuMbox timeout for core_id:0, func_id:0 WIFI_MAIL_API_GET_WAIT_COUNTER fail! USB driver version: 7523.3.20210202 port 0 u2_slew_rate_cal_7523 FM_OUT value = 107(0x0000006B) SR calibration value = 5 port 1 u2_slew_rate_cal_7523 FM_OUT value = 107(0x0000006B) SR calibration value = 5 xhci-hcd 1fab0000.xhci: xHCI Host Controller xhci-hcd 1fab0000.xhci: new USB bus registered, assigned bus number 1 xhci-hcd 1fab0000.xhci: irq 111, io mem 0x1fab0000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci-hcd 1fab0000.xhci: xHCI Host Controller xhci-hcd 1fab0000.xhci: new USB bus registered, assigned bus number 2 usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver cypress_m8 usbserial: USB Serial support registered for DeLorme Earthmate USB usbserial: USB Serial support registered for HID->COM RS232 Adapter usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3316 buckets, 13264 max) ludewei add module gre: GRE over IPv4 demultiplexor driver IPv4 over IPsec tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. Ebtables v2.0 registered l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 lib80211: common routines for IEEE802.11 drivers Registering SWP/SWPB emulation handler tc3162ser_startup VFS: Mounted root (squashfs filesystem) readonly on device 31:8. Freeing unused kernel memory: 240K busybox init and set aff starting pid 444, tty '': '/etc/init.d/rcS' insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/scsi_mod.ko': No such file or directory insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/sd_mod.ko': No such file or directory insmod: can't insert '/lib/modules/kmdir/kernel/drivers/scsi/scsi_wait_scan.ko': No such file or directory insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/core/usbcore.ko': No such file or directorusbcore: registered new interface driver usb-storage y insmod: can't insert '/lib/modules/kmdir/kernel/fs/fuse/fuse.ko': No such file or directory insmod: can't insert '/lib/modules/kmdir/kernel/fs/nls/nls_utf8.ko': No such file or directory insmod: can't insert '/lib/modules/kmdir/kernel/fs/nls/nls_cp936.ko': No such file or directory tp_board: loading out-of-tree module taints kernel. Register flash device: flash0 rcS (444): drop_caches: 3 start XPON related APP /tmp/cfg_load is not exist,left time 30 svchost_parse_print_conf: Path = /lib/libcfg_clisvc.so svchost_parse_print_conf: Entry = svc_cfg_main svchost_parse_print_conf: Param = 111 random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) shm_pool_init: base[20000000] size[00200000]] shm_pool_init: Init Done! random: ubusd: uninitialized urandom read (4 bytes read, 15 bits of entropy available) svc_cfg_start: ........ Load cfg from file [/var/romfile.cfg] ..... tar: invalid mag[check_checksum:738]:tc_checksum open file(/tmp/ctromfile.cfg) failed===> ic tar: short read cp: can't s[check_romfile:918]:check_checksum=-1,Romfile checksum is wrong===> tat '/tmp/ctromfile.cfg': No such file or directory Use backup romfile to check! Couldn't open mtd:reservearea! mtd[readflash]:device=reservearea tclen=262144 tcoffset=524288 Unlocking reservearea ... Could not open mtd device: reservearea [BK_ROMFILE_FLAG]/userfs/bin/mtd readflash /tmp/tc_backupromfile 262144 524288 reservearea tar: invalid ma[check_checksum:738]:tc_checksum open file(/tmp/ctromfile.cfg) failed===> gic tar: short read cp: can't s[check_romfile:918]:check_checksum=-1,Romfile checksum is wrong===> tat '/tmp/ctromfile.cfg': No such file or directory Use default romfile to check! mtd[readflash]:device=reservearea tclen=262144 tcoffset=786432 Unlocking reservearea ... Could not open mtd device: reservearea [DEF_ROMFILE_FLAG]/userfs/bin/mtd readflash /tmp/tc_defaultromfile 262144 786432 reservearea tar: invalid ma[check_checksum:738]:tc_checksum open file(/tmp/ctromfile.cfg) failed===> gic tar: short read cp: can't st[check_romfile:918]:check_checksum=-1,Romfile checksum is wrong===> at '/tmp/ctromfile.cfg': No such file or directory /tmp/cfg_load is not exist,left time 29 Use usrfs romfile to check! mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea ctromfile.cfg <<call handle_proline_paras>> mtd[readflash]:device=[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea handle_proline_paras 1564 SSID:ChinaNet-AP. [ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. ha[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. ndle_pr[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. oline_p[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. aras 1[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. 564 WPA[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. PSK:123[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. 45678.[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. ha[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. ndle_prrandom: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available) oline_para[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. s 156[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. 4 SSID[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. :Chinarandom: ubusd: uninitialized urandom read (4 bytes read, 41 bits of entropy available) Net-AP. handle_pr[ponmgr_lib_ioctl][196]:===Fail Exit===Couldn't open /dev/pon, fd = -1. oline_paras 1564 WPAPSK:12345678. handle_proline_prandom: ubusd: uninitialized urandom read (4 bytes read, 42 bits of entropy available) aras 1564 SSID:ChinaNet-AP. handle_proline_paras 1564 WPAPSK:12345678. handle_proline_paras 1564 SSID:ChinaNet-AP. handle_proline_paras 1564 WPAPSK:12345678. handle_proline_paras 1564 web_passwd:1234. handle_proline_paras 1564 SerialNumber:FHTT12345678. parse proline para Password fail. parse proline para Password fail. handle_proline_paras 1564 Mode:GPON. root.mesh.apclibh.entry.1:BhProfileSsid not found. root.mesh.apclibh.entry.1:BhProfileWpaPsk not found. root.mesh.apclibh.entry.2:BhProfileSsid not found. root.mesh.apclibh.entry.2:BhProfileWpaPsk not found. handle_proline_paras 1564 (null):1. cfg_save_object: open file [/tmp/var/romfile.cfg] fail ----> Load config file fail. svc_cfg_start: ........ ok [20001030]! svchost_get_event_val: get param fail [0] start omci svchost_prandom: ubusd: uninitialized urandom read (4 bytes read, 56 bits of entropy available) arse_print_conf: Path = /lib/libcentral_ctrl_svc.so svchost_parse_print_conf: Entry = svc_central_ctrl_main svchost_parse_print_conf: Param = 111 module_sel: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint ecnt_register_cpu_interruptssvchost_p random: ubusd: uninitialized urandom read (4 bytes read, 58 bits of entropy available) arse_print_conf: Path = /lib/libpon_svc.so svchost_parse_print_conf: Entry = svc_pon_main svchost_parse_print_conf: Param = 111 TC3162 LED Manager 0.1 init tcledctrl version: tcledctrl V1.1.0.0 (Mar 19 2024-09:20:52). led path:/userfs/7529_62led.conf random: ubusd: uninitialized urandom read (4 bytes read, 60 bits of entropy available) svc_centrl_ctrl_init: ...... reg event ok dev mount is start! config 0 PID=552 event receive pthread_create OK, keep going...... svchost_get_event_val: get param fail [0] random: ubusd: uninitialized urandom read (4 bytes read, 64 bits of entropy available) open /proc/tc3162/reset_button faile. open /proc/tc3162/button_type faile. open /proc/tc3162/led_switch_button faile. svc_pon_int: ...... reg event ok svc_pon_int: ...... reg method ok cfg svc load done, 0 ms svchost_get_event_val: get param fail [0] [svc_cfg_load_special_info][581]SET [omci_lib_set_max_ports_list] Result=0 Couldn't open mtd:reservearea! mount: mounting /dev/mtdblock0 on /usr/config/WLan/MAP failed: No such file or directory mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea Can't open /etc/devicnlksock_create:nlksock create err:Protocol not supported! eParaStatic.conf Can't open /etc/active_notify_handler: nlksock_create fail deviceParaStatic.conf Can't open /etc/devirandom: ubusd: uninitialized urandom read (4 bytes read, 75 bits of entropy available) ceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf [svc_cfg_load_special_info][639]SET [omci_lib_set_onu_version] Result=0 mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf mtd[readflash]:device=reservearea tclen=1 tcoffset=2097152 Unlocking reservearea ... Could not open mtd device: reservearea mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reserveatccicmd V1.1.0.0 (Mar 19 2024-09:20:58) rERROR!Create /etc/fwTCver.conf fail! ea ... Could not open mtd device: reservearea Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf [svc_cfg_load_special_info][654]SET [omci_lib_set_equipment_id] Result=0 mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't SIFMaster 0.1 init ===== Interface 0 is ON ===== Register sifm cmd open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf [svc_cfg_load_special_info][661]SET [oam_lib_set_hardware_version] Result=0 mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not open mtd device: reservearea Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf [svc_cfg_load_special_info][666]SET [oam_lib_set_software_version] Result=0 mtd[readflash]:device=reservearea tclen=2120 tcoffset=1310720 Unlocking reservearea ... Could not ope(gdump_mode_sel): GDUMP sel has switch to 3 ECNT_HOOK_ERROR occur. ECNT_API_XPON_MODE_GET:215 n mtd device: reservearea Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf Can't open /etc/deviceParaStatic.conf [svc_cfg_load_special_info][672]SET [oam_lib_set_onu_model] Result=0 insmod: can't insert '/lib/modules/crypto_k.ko': No such file or directory ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:2 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:2 ifc_set_action: cpu:1, nbq:2 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:3 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:1 ifc_set_action: cpu:1, nbq:7 ifc_set_action: cpu:1, nbq:8 TP_User Ecnt ponTime:OMCI Startup macType = 0 flashQdmaInit = 0x33 netif_napi_add() called with weight 256 on device lan_int2_if ether.c:v1.00-NAPI 29.Mar.2015 eth0: FE MAC Ethernet address: 8C:90:2D:06:A9:48 Use Internal switch ,type 10 tcPhyVerLookUp 2446 94A1 7523 Ge, , port_num = 0, ephy_addr = 9, ephy_addr_base = 0x9 GE Rext AnaCal Done! (7)(0x27) GE Rext AnaCal Done! (7)(0x27) GE R45 AnaCal zcal_idx(before table) (dec: 48) (hex: 0x30) GE R45 AnaCal Done! (cnt:16)(after table) ([7][6:0]:0x4a) ([6:0]:0xca) GE R45 AnaCal zcal_idx(before table) (dec: 46) (hex: 0x2e) GE R45 AnaCal Done! (cnt:14)(after table) ([7][6:0]:0x4e) ([6:0]:0xce) GE R45 AnaCal zcal_idx(before table) (dec: 46) (hex: 0x2e) GE R45 AnaCal Done! (cnt:14)(after table) ([7][6:0]:0x4e) ([6:0]:0xce) GE R45 AnaCal zcal_idx(before table) (dec: 45) (hex: 0x2d) GE R45 AnaCal Done! (cnt:13)(after table) ([7][6:0]:0x51) ([6:0]:0xd1) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (3)(0x22) GE Tx offset AnaCal Done! (1)(0x1) GE Tx amp AnaCal Done! (4) (0x24) Unlocking config ... Could not open mtd device: config GE Tx amp AnaCal Done! (21) (0x35) GE Tx amp AnaCal Done! (21) (0x35) GE Tx amp AnaCal Done! (14) (0x2e) [tcPhyInit] in [tcPhyInit] out , r31 = (9, 0x0) tcPhyVerLookUp 2446 94A1 7523 Ge, , port_num = 1, ephy_addr = 10, ephy_addr_base = 0x9 GE R45 AnaCal zcal_idx(before table) (dec: 48) (hex: 0x30) GE R45 AnaCal Done! (cnt:16)(after table) ([7][6:0]:0x4a) ([6:0]:0xca) GE R45 AnaCal zcal_idx(before table) (dec: 45) (hex: 0x2d) GE R45 AnaCal Done! (cnt:13)(after table) ([7][6:0]:0x51) ([6:0]:0xd1) GE R45 AnaCal zcal_idx(before table) (dec: 45) (hex: 0x2d) GE R45 AnaCal Done! (cnt:13)(after table) ([7][6:0]:0x51) ([6:0]:0xd1) GE R45 AnaCal zcal_idx(before table) (dec: 45) (hex: 0x2d) GE R45 AnaCal Done! (cnt:13)(after table) ([7][6:0]:0x51) ([6:0]:0xd1) GE Tx offset AnaCal Done! (7)(0x26) GE Tx offset AnaCal Done! (2)(0x2) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (1)(0x20) GE Tx amp AnaCal Done! (8) (0x28) GE Tx amp AnaCal Done! (15) (0x2f) GE Tx amp AnaCal Done! (8) (0x28) GE Tx amp AnaCal Done! (15) (0x2f) [tcPhyInit] in [tcPhyInit] out , r31 = (10, 0x0) tcPhyVerLookUp 2446 94A1 7523 Ge, , port_num = 2, ephy_addr = 11, ephy_addr_base = 0x9 GE R45 AnaCal zcal_idx(before table) (dec: 46) (hex: 0x2e) GE R45 AnaCal Done! (cnt:14)(after table) ([7][6:0]:0x4e) ([6:0]:0xce) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (1)(0x1) GE Tx offset AnaCal Done! (2)(0x2) GE Tx amp AnaCal Done! (4) (0x24) GE Tx amp AnaCal Done! (11) (0x2b) GE Tx amp AnaCal Done! (2) (0x22) GE Tx amp AnaCal Done! (8) (0x28) [tcPhyInit] in [tcPhyInit] out , r31 = (11, 0x0) tcPhyVerLookUp 2446 94A1 7523 Ge, , port_num = 3, ephy_addr = 12, ephy_addr_base = 0x9 GE R45 AnaCal zcal_idx(before table) (dec: 45) (hex: 0x2d) GE R45 AnaCal Done! (cnt:13)(after table) ([7][6:0]:0x51) ([6:0]:0xd1) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE R45 AnaCal zcal_idx(before table) (dec: 43) (hex: 0x2b) GE R45 AnaCal Done! (cnt:11)(after table) ([7][6:0]:0x56) ([6:0]:0xd6) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (2)(0x21) GE Tx offset AnaCal Done! (3)(0x22) GE Tx offset AnaCal Done! (7)(0x26) GE Tx amp AnaCal Done! (7) (0x27) GE Tx amp AnaCal Done! (4) (0x24) GE Tx amp AnaCal Done! (6) (0x26) GE Tx amp AnaCal Done! (4) (0x24) [tcPhyInit] in mount: can' not found str : MAP, erase and mount again t dev_mount is ok find /dev/mtdblock in /etc/fstab [tcPhyInit] out , r31 = (12, 0x0) eth0: starting interface. netif_start_queue macType = 0 flashQdmaInit = 0x33 fe resource init start 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left 16 acnt1 id has been used, there is no left Ralink HW NAT Module Enabled you need to modify struct FoeEntryExtKernel in ecnt_forward_left_to_right.h when you modifyied struct FoeEntryExt!SRAM_FOE_NUM=7, means PPE_FOE_NUM=512 HWNAT Module enabled with Type:L2B/IPv4/IPv6/DS-LITE/6RD, foeSize:64B, sram_foeNum:512, dram_foeNum:16384 IP check use Black List EN7523 PPE SRAM HW default setting is 512 at 64byte, no need to set by sw [c0847268]isForceToCpu=0:0 copy NPU binary:/userfs/npu_rv32.bin(60264 Bytes) to 0xd0f00000 copy NPU binary:/userfs/npu_data.bin(728 Bytes) to 0xd0b80000 [C0]core freq at 333000000 Hz [C0]timer_init: Timer clk is running at 125 Mhz [C0]wcid_counter_init:0 [C0]wcid_counter_init:1 [C0][NPU] ba_node_init... [C0]baNode_array_init [C0]counter_init:2 [C0][NPU] queue_mutex_init... [C0]qdma_init [C1]core1_main [C2]timer_isr Store Value 1e903000, val[C2]core2_main [C3]core3_main [C3]do npu_enq_deq_init [c0847244]npu_pkt_buf_addr=8dff37c0 npu_wifi_offload_get_pkt_buf_addr=8dff37c0 [c0847244]npu_pkt_buf_addr=8dff37c0 [C0]wifi_mail_data->wifi_mail_private.npuPktBufAddr=8dff37c0, 8dff37c0 npu_wifi_offload_get_force_to_cpu_flag=0 isForceToCpu=0 [C0](core0_main) just return, because QDMA driver for ARM is not ready whnat_module_init(): module init and register callback for whnat create whnat_ctrl ok!!! wed_slot_map_get(): assign slot_id:0 for entry: 0! wed_slot_map_get(): assign slot_id:1 for entry: 1! tso_lan: tso_v2.c [201]: dscpDmaAddr =8a2c0000 tso_lan: tso_v2.c [263]: diPtr->dscpIdx = 0 tso_lan: tso_v2.c [263]: diPtr->dscpIdx = 0 tso_proc_init. val_string:add v4 - 445 - - dport:0, sport:445, daddr:0, saddr:0 ---- 7570_bob.conf ---- ---- cp -f /etc/7570_bob.conf /tmp/ ---- do_tp_readPONCalibrationFlashTo7570bobFileWithCheck, 296: PON FLASH CALIB: data[0]=7e data[1]=06 data[2]=bb data[3]=05 do_tp_readPONCalibrationFlashTo7570bobFileWithCheck, 322: read pon calibration flash success! ---- flashtool readflashtobob ---- ______ XPON_PHY init ______ little endian NCPO_RECOVER 0, PHY_TX_TDC_HOLD_EN 0, NCPO_RECOVER_DBG_MSG 0 xPON PHY initialization done E3 patched EN7571 found! FLASH matrix got PWRADC offset = 0x3838 PWRADC ready BG 1.76V = 0x284 BG 0.875V = 0x13e RSSI_Vref = 0x211 RSSI_V = 0x28d eFuse value = 0x0 eFuse offset = 0.0'C Start GPON Tx Calibration CDR disabled RGS_T0C = 0x49 RGS_T1C = 0x4b CDR enabled APD initialization done en7571_reg_init Initial current loaded PWR/ER loaded TIASD = 0x3d Rx LOS is set Internal DDMI Enabled KT Enabled EN7571 Initialization Done! PON PHY driver version is 2100825.116.11 xPON driver initialization Alloc data struct memory successful, 36508 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 the channel id_is must between 0 and 15 XPON Mapping Module init OK! VoIPBasic_Comm [1970-1-1 Thu 00:00:14.194461]omci start! on [1970-1-1 Thu 00:00:14.198721]main gponOmciCmsgsrvInit vtag_drv_init SIPProtocol is SIP prevSipStatus: 0, curSipStatus: [1970-1-1 Thu 00:00:14.209623]OMCI wait for DM init... 0 voip_evt.buf: root.voipbasic.common, type: 3, random: nonblocking pool is initialized evt_id: 0x000001c0 tc_multiwan version: tcsmux V1.1.0.0 (Mar 19 2024-09:21:03). pon_vlan_init Multi Lan port initilize xpon igmp module....done! pon_mac_filter_init Multi Lan portinsmod: can't insert '/lib/modules/mtk_xpon PPTP VPN offload module init _multicast.ko': No such file or directory L2TP VPN offload module init device eth0 entered promiscuous mode device eth0.1 is not a slave of br0 device eth0.2 is not a slave of br0 device eth0.3 is not a slave of br0 device eth0.4 is not a slave of br0 device eth0 is already a member of a bridge; can't enslave it to bridge br0. device eth0 left promiscuous mode br0: port 1(eth0) entered disabled state IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready device eth0.1 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready device eth0.2 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): eth0.3: link is not ready device eth0.3 entered promiscuous mode device eth0.4 is not a slave of br0 ifconfig: ioctl 0x8913 failed: No such device interface eth0.5 does not exist! insmod: can't insert '/lib/modules/igmpsnoop.ko': No such file or directory insmod: can't insert '/lib/modules/mldsnooping.ko': No such file or directory insmod: can't insert '/lib/modules/lro_lan.ko': No such file or directory insmod: can't insert '/lib/modules/lro_wan.ko': No such file or directory ifconfig: SIOCSIFMTU: Invalid argument vlan tag restore switch : enable insmod: can't insert '/lib/modules/dying_gasp.ko': No such file or directory start ponmgr_cfg MTK DSP support rcS (444): drop_caches: 3 set pptp_offload proto value 1 rcS.sdk init done! creat_domain_proc ok tp_domain init ok device recognition register success status: DSPCore[Ver:TVB1.0.23.800-4-P102-1] [1] PCM V2.4 (Dec 18 2023 23:20:57) bind irq-113 to CPU1 PCM_INT=28 pcm[Ver:TVB1.0.23.800-4-P102-1] lec[Ver:TVB1.0.23.800-4-P102-1] SYS_HCLK=250 Major Num:233, device: spi spi[Ver:TVB1.0.23.800-4-P102-1] [15.813][cos] 422 - ERROR: before cpu mask 00000003 [15.814][cos] 437 - ERROR: after cpu mask 00000001 ========fxs3 init start======== ========fxs3 init complete======== . init mod-slic3 slic3[Ver:TVB1.0.23.800-1] mode= ISI init mod-ksocket ksocket[Ver:TVB1.0.23.800-1] ortp[Ver:TVB1.0.23.800-4-P102-1] monitor value xxxxxxx init mod-acodec acodec[Ver:TVB1.0.23.800-4-P102-1] init mod-foip3 foip3[Ver:TVB1.0.23.800-4-P102-1] ponTime:ONU Ready mtd[readflash]:device=reservearea tclen=1 tcoffset=2097152 Unlocking reservearea ... Could not open mtd device: reservearea Interface name length cannot exceed 15 characters. ponTime:Connection Start working_mode: 10 [42949389810ms][phy_init.c:1356] __2__PON_SET_PHY_START__1st__ [1]is_config_mode=0 [2]phy_start irq=0 ==> EPON OAM Start need 0s:182439us Interface name length cannot exceed 15 characters. Silabs SLIC type selected by SW makefile compile option [4294938988][slic][INFO][gpio_clocksrc_init:L2399]ISI [4294938989][spi][INFO][SPI_Reset:L473] SPI_Reset 2 slic deviceVerify ProSLIC_Version 9.1.0 Silabs SLIC Reset REG_0 = 0xaa ,device[0], Part_num 0x5, Revision 0x2 device[0]:deviceVerify Success! SPI Reset times:1 pcm1 ch num:1 pcm2 ch num:0 fxs[Ver:TVB1.0.23.800-4-P102-1] [fxs_init_action](1344)noinit=0 pcm1 ch num:1 pcm2 ch num:0 Init fxsNum(1) + fxoNum(0) = slic_ch_num(1) , deviceNum(1) deviceInit on DeviceId = 0 ProSLIC_createControlInterface = 0 ProSLIC_createDevice = 0 get_start_chanid=0 ProSLIC_createChannel = 0 ProSLIC_SWInitChan = 0 device [0] chanPvt[0].chanType 1 device [0] chanPvt[0].chipType 6 Si3218x_Init_with_Options(640) size = 1 init_opt = 0 SiVoice: Channel 0: Type = PROSLIC Rev = 2 ProSLIC:loading patch: 06302015 . Si3218x: Channel 0 : VBAT Up = 59.440 v [42949390820ms][phy_init.c:1946] PON PHY scu_reset_init mode=10 [42949390820ms][phy.c:839] __1__phy_mode_config__1st__ [1]is_config_mode=1 [2]phy_start irq=2 mode: 1 [42949390820ms][phy_init.c:1946] PON PHY scu_reset_init mode=1 [42949390840ms][phy_init.c:1553] __1__phy_mode_config__req_isr__ [1]is_config_mode=1 [2]phy_start irq 2 ==> 1 Auto GPON ProSLIC:Starting LB Cal on channel 0 .init mod-vdsp for 1 channels 2 sessions vdsp[Ver:TVB1.0.23.800-4-P102-1] =============================== || MTK DSP init successfully || =============================== pid 2's current affinity mask: 3 pid 890's current affinity mask: 1 IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready ___ COUNTRY SETTING ___ ring_idx : 0 imp_idx : 0 ProSLIC:PCMStart slic_set_gainLv - fffffffa / 0 pid 890's new affinity mask: 2 fxsSetLine[0]state 0x9 State UNKNOWN ! pid 2's current affinity mask: 3 pid 2's current affinity mask: 3 pid 2's current affinity mask: 3 pid 1090'Dump SLIC[0] register: ================================= 00 01 02 03 04 05 06 07 08 09 s================================= 00: aa 00 00 1f 00 40 00 a2 e5 ff 10: 25 13 00 00 00 20 00 00 00 00 20: 00 00 00 02 00 00 00 00 00 00 30: 11 00 00 10 00 00 00 02 00 40 40: 1f 00 7d 00 00 59 04 10 66 00 50: 00 00 00 00 00 00 00 00 ff 00 60: 00 00 e4 00 00 00 00 00 f0 00 70: 00 00 00 00 00 00 02 00 00 00 80: 3f 01 b7 03 af 05 0ec 0f ed 10 90: 40 07 9f 06 c1 11 24 05 80 05 100: 00 01 00 00 00 00 00 00 00 00 110: 00 00 47 01 fc 00 02 ff 38u 00 120: 63 05 87 05 00 20 03 00 ================================= rrent write address(47) value : 0x8 affinity mask: 1 pid 1090's new affinity mask: 2 [20.670][cos] 317 - ERROR: checkMiscSize: MTD_OFS_PC_HISTORY_ADDR(3e60000) + MTD_OFS_PC_HISTORY_SIZE(60000) = (3ec0000) [20.737][cmm] 2219 - ERROR: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml /etc/init.d/rcS: line 195: can't create /proc//oom_score_adj: nonexistent directory rcS (444): drop_caches: 3 rcS init done! Please press Enter to activate this console. sleep 90s! [21.679][cmm] 1048: X_TP_ConfigVersion 5a000002, X_TP_DMVersion 5a000002 [21.Disable GPON ONU 683][cos] 715 - ERROR: Disable gpon driver before true SN set [21.688][cos] 253 - ERROR: COS wait for OMCI init... [21.688][cos] 259 - ERROR: OMCI init use 0 seconds! ===========>manufacture:0, ISPflag:0 IPv6: ADDRCONF(NETDEV_UP): br_agc: link is not ready device eth0.1 left promiscuous mode br0: port 1(eth0.1) entered disabled state device eth0.2 left promiscuous mode br0: port 2(eth0.2) entered disabled state device eth0.3 left promiscuous mode br0: port 3(eth0.3) entered disabled state device eth0.4 is not a slave of br0 interface eth0.5 does not exist! device eth0.1 entered promiscuous mode [1970-1-1 Thu 00:00:22.300189]DM init use 8 seconds! [1970-1-1 Thu 00:00:22.308857]OMCI wait for RSL init... device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): eth0.4: link is not ready device eth0.4 entered promiscuous mode ifconfig: ioctl 0x8913 failed: No such device sh: can't create /proc/sys/net/ipv6/conf/eth0.5/disable_ipv6: nonexistent directory interface eth0.5 does not exist! br_agc: port 1(eth0.1) entered forwarding state br_agc: port 1(eth0.1) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): br_agc: link becomes ready updateDevBandWidthMac:index=0,d0:bf:9c:26:fa:65 sendto: No such file or directory line(593) Msg.type(2014) pid(860) errno(2) ret(-1) [ read_dhcpc_config ] 128: error, unable to open config file: /var/tmp/dconf/udhcpc.conf [24.600][cos] 121 - ERROR: CQC:tm_start:24, tm_end:24 [err] syslogd[syslogd_msg_process --673] syslogd : log module is not config [26.610][cos] 121 - ERROR: CQC:tm_start:24, tm_end:26 [err] syslogd[syslogd_msg_process --673] syslogd : log module is not config [28.620][cos] 121 - ERROR: CQC:tm_start:24, tm_end:28 [err] syslogd[syslogd_msg_process --673] syslogd : log module is not config [30.630][cos] 121 - ERROR: CQC:tm_start:24, tm_end:30 [30.630][cos] 137 - ERROR: CQC:FAILED! [30.630][cos] 775 - ERROR: Expire time! device eth0.1 left promiscuous mode br_agc: port 1(eth0.1) entered disabled state device eth0.2 left promiscuous mode br_agc: port 2(eth0.2) entered disabled state device eth0.3 left promiscuous mode br_agc: port 3(eth0.3) entered disabled state device eth0.4 left promiscuous mode br_agc: port 4(eth0.4) entered disabled state interface eth0.5 does not exist! [30.973][cmm] 591: num of CPU core = 2. [30.973][cmm] 601: parent pid 860 [31.077][cmm] 608: start creating dropbear RSA key at CPU core 1. [31.078][cmm] 618: child pre cpu mask 00000001 [31.078][cmm] 632: child post cpu mask 00000002 [31.079][cmm] 636: Try create dropbear RSA key loop=0 ... Generating 2048 bit rsa key, this may take a while... [31.263][cmm] 3192 - ERROR: Open TZ file error! ddns_ud> start enable = 0, server: , auth: , request killall: dnsmasq: no process killed [31.736][cmm] 158 - WARN: Empty DNSServer() [31.949][cmm] 158 - WARN: Empty DNSServer() [31.996][cmm] 158 - WARN: Empty DNSServer() [32.005][cmm] 158 - WARN: Empty DNSServer() [32.016][cmm] 158 - WARN: Empty DNSServer() bridge name br0 has exist bridge name br0 has exist device br0 already exists; can't create bridge with the same name [32.148][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [32.149][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [32.149][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [32.149][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [32.149][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [32.150][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [32.150][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [32.150][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [32.150][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [32.151][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready or pUrl() [32.151][cutil] 500 - ERROR: send DNS Query for domain(0.pool.ntp.org) fail, errno str: No such file or directory [32.151][cutil] 555 - ERROR: get ip for 0.pool.ntp.org failed [32.152][cutil] 500 - ERROR: send DNS Query for domain(0.pool.ntp.org) fail, errno str: No such file or directory [32.152][cutil] 555 - ERROR: get ip for 0.pool.ntp.org failed [32.152][cutil] 1998 - ERROR: Failed to sendto [32.153][cutil] 1998 - ERROR: Failed to sendto [32.153][cutil] 500 - ERROR: send DNS Query for domain(1.pool.ntp.org) fail, errno str: No such file or directory [32.153][cutil] 555 - ERROR: get ip for 1.pool.ntp.org failed [32.154][cutil] 500 - ERROR: send DNS Query for domain(1.pool.ntp.org) fail, errno str: No such file or directory [32.154][cutil] 555 - ERROR: get ip for 1.pool.ntp.org failed [32.154][cutil] 1998 - ERROR: Failed to sendto [32.154][cutil] 1998 - ERROR: Failed to sendto [32.155][cutil] 500 - ERROR: send DNS Query for domain(2.pool.ntp.org) fail, errno str: No such file or directory [32.155][cutil] 555 - ERROR: get ip for 2.pool.ntp.org failed [32.155][cutil] 500 - ERROR: send DNS Query for domain(2.pool.ntp.org) fail, errno str: No such file or directory [32.155][cutil] 555 - ERROR: get ip for 2.pool.ntp.org failed [32.156][cutil] 1998 - ERROR: Failed to sendto [32.156][cutil] 1998 - ERROR: Failed to sendto [32.156][cutil] 500 - ERROR: send DNS Query for domain(3.pool.ntp.org) fail, errno str: No such file or directory [32.157][cutil] 555 - ERROR: get ip for 3.pool.ntp.org failed [32.157][cutil] 500 - ERROR: send DNS Query for domain(3.pool.ntp.org) fail, errno str: No such file or directory [32.157][cutil] 555 - ERROR: get ip for 3.pool.ntp.org failed [32.157][cutil] 1998 - ERROR: Failed to sendto [32.158][cutil] 1998 - ERROR: Failed to sendto [32.158][cutil] 500 - ERROR: send DNS Query for domain(pool.ntp.org) fail, errno str: No such file or directory [32.158][cutil] 555 - ERROR: get ip for pool.ntp.org failed [32.159][cutil] 500 - ERROR: send DNS Query for domain(pool.ntp.org) fail, errno str: No such file device eth0.1 entered promiscuous mode obr0: port 1(eth0.1) entered forwarding state br0: port 1(eth0.1) entered forwarding state r IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready directory [32.159][cutil] 555 - ERROR: get ip for pool.ntp.org failed [32.159][cutil] 1998 - ERROR: Failed to sendto [32.159][cutil] 1998 - ERROR: Failed to sendto NTP server list: done [32.309][cmm] 203 - ERROR: ifName is eth0, vid is 5 [32.331][cmm] 203 - ERROR: ifName is eth0, vid is 4 vconfig: ioctl error for add: File exists [32.344][cmm] 203 - ERROR: ifName is eth0, vid is 3 vconfig: ioctl error for add: File exists [32.357][cmm] 203 - ERROR: ifName is eth0, vid is 2 vconfig: ioctl error for add: File exists [32.370][cmm] 203 - ERROR: ifName is eth0, vid is 1 vconfig: ioctl error for add: File exists [32.383][cmm] 203 - ERROR: ifName is eth0, vid is 0 sh: can't create /proc/tplink/eth_vlan: nonexistent directory [32.543][cmm] 257 - ERROR: pAddIfMsg->addIfName:br0 pAddIfMsg->boundIfName: Bad argument `REJECT' Try `ip6tables -h' or 'ip6tables --help' for more information. [32.578][ipv6] 1015 - WARN: Could not find pid of dibbler-server with interface name is br0! Starting daemon... [32.906][ipv6] 1380 - WARN: Could not find pid of radvd with interface name is br0! device eth0.2 entered promiscuous mode iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). device eth0.3 entered promiscuous mode br0: port 1(eth0.1) entered disabled state device eth0.1 left promiscuous mode br0: port 1(eth0.1) entered disabled state br0: port 2(eth0.2) entered disabled state device eth0.2 left promiscuous mode br0: port 2(eth0.2) entered disabled state br0: port 3(eth0.3) entered disabled state device eth0.3 left promiscuous mode br0: port 3(eth0.3) entered disabled state device eth0.4 is not a slave of br0 device eth0 entered promiscuous mode br0: port 1(eth0) entered forwarding state br0: port 1(eth0) entered forwarding state device eth0 left promiscuous mode br0: port 1(eth0) entered disabled state device eth0.1 entered promiscuous mode br0: port 1(eth0.1) entered forwarding state br0: port 1(eth0.1) entered forwarding state device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode device eth0.4 is not a slave of br0 device eth0.5 is not a slave of br0 device eth0.4 is not a slave of br0 sh: can't create /sys/devices/virtual/net/eth0.4/brport/multicast_router: nonexistent directory [Mar 19 00:00:33] radvd: poll error: Interrupted system call sh: can't kill pid 1552: No such process [33.871][cmm] 159 - ERROR: band:2.4GHz has created public apObj, apObj.X_TP_APType:Public [33.872][cmm] 169 - ERROR: 2.4GHz radio has created the public apObj, go next. [33.872][cmm] 159 - ERROR: band:5GHz has created public apObj, apObj.X_TP_APType:Public [33.872][cmm] 169 - ERROR: 5GHz radio has created the public apObj, go next. [33.873][cmm] 2023 - ERROR: Dut is not in manufacturing mode!devInfoObj.X_TP_IsManufacture:0 ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device ra0: ===> main_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT load l1profile succeed! WHNAT=1 whnat_cap_support(): chip_id=7915 is in WHNAT support list wifi_slot_get(): bus name=PCI Bus 0000:02, funid=8, get slot id=1 whnat_entry_acquire(): PCIE SLOT:1, hook to WHNAT,entry id=1 wed_init(1): irq=91,base_addr=0xd575e000 ----->wed_tx_ring_init() 805 len=40 ----->wed_tx_ring_init() 816 len=98376 sizeof(whnat_ring)=49188, ring_ctrl->ring_num=2 tx_ring_init() whnat_dma_buf_alloc for glb_ring_ctrl_desc[0]=32768 tx_ring_init() whnat_dma_buf_alloc for glb_ring_ctrl_desc[1]=32768 wed_ring_init(): wed ring init result = 0 token_info_init() whnat_dma_buf_alloc for glb_wed_buf_res=114688 whnat_dma_buf_alloc for glb_var_whnat_fbuf[1]=917504 ---------> token_info_alloc() len=372736, eid=7168, sizeof(struct wed_token_info)=52 skb_len=1900 [ reacreate wed ok!!! wdma_init(): wdma(1) base addr=d5872400 wdma_init(): wdma(1) irq[0]=87 wdma_init(): wdma(1) irq[1]=88 wdma_init(): wdma(1) irq[2]=89 rx_ring_init() whnat_dma_buf_alloc for glb_wdma_rx_ring_ctrl[0]=16384 d_dhcrx_ring_init() whnat_dma_buf_alloc for glb_wdma_rx_ring_ctrl[1]=16384 pcwifi_chip_probe(): Chang CHIP IRQ: 83 to WHNAT IRQ: 91 wifi_slot_get(): bus name=PCI Bus 0000:02, funid=8, get slot id=1 whnat_probe(): probe fail since whnat is full! whnat_dev0: probe of 1fa02000.wed2 failed with error -1 _mt_service_open: wlan service opens successfully! config ] 128: error, unable to open config file: /var/tmp/dconf/udhcpAPWdsInitialize():WdsEntry[0~15] c.conf multi_profile_merge_radius_key:RTMPGetKeyParameter 717 fail![multi_profile_merge_5g_only] DBDC_MODE=1 multi-profile merge success, en:1,pf1_num:7,pf2_num:7,total:14 Open file "/var/Wireless/RT2860AP/DBDC_card0.dat" to store DBDC cfg! (23) Write file "/var/Wireless/RT2860AP/DBDC_card0.dat" success (size=8228)! BssidNum=14 Pf2MbssIdxMap: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 MacAddress7 = 00:00:00:00:00:00 E2pAccessMode=2 SSID[0]=xx230v, EdcaIdx=0 SSID[1]=TP-Link_A948_1, EdcaIdx=0 SSID[2]=TP-Link_A948_2, EdcaIdx=0 SSID[3]=TP-Link_A948_Guest, EdcaIdx=0 SSID[4]=faebf9dddc456bdbf50493974d9a66, EdcaIdx=0 SSID[5]=b4c189bf248de84e89d342353fe64b, EdcaIdx=0 updateDevBandWidthMac:index=0,d0:bf:9c:26:fa:65 SSID[6]=e2b6520c958f5e14820332d7ee1a39, EdcaIdx=0 SSID[7]=xx230v, EdcaIdx=0 SSID[8]=TP-Link_A948_1, EdcaIdx=0 SSID[9]=TP-Link_A948_2, EdcaIdx=0 SSID[10]=TP-Link_A948_Guest, EdcaIdx=0 SSID[11]=c45ffb9fc9a75f285a29c8acdafbe9, EdcaIdx=0 SSID[12]=55e50cbef544413f4552145cd6ef04, EdcaIdx=0 SSID[13]=895292acce55edb97159c9a0006ea6, EdcaIdx=0 RTMPSetProfileParameters(): DBDC Mode=1, eDBDC_mode = 1 cfg_mode=16 cfg_mode=16 cfg_mode=16 wmode_band_equal(): Band Equal! cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=16 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 cfg_mode=17 auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 3 auto_ch_select_set_cfg(): BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3 RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 2G Channel of config parameter must set 0: Index0 Channel=1 RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: RTMPChannelCfg:Warning:ACS Enable and the 5G Channel of config parameter must set 0: Index1 Channel=36 BndStrgBssIdx=1;0;0;0;0;0;0;1;0;0;0;0;0;0 [TxPower] BAND0: 100, BAND1: 100 [SKUenable] BAND0: 1, BAND1: 1 [PERCENTAGEenable] BAND0: 1, BAND1: 1 profile: FragThreshold[0]=2346 profile: FragThreshold[1]=2346 profile: FragThreshold[2]=2346 profile: FragThreshold[3]=2346 profile: FragThreshold[4]=2346 profile: FragThreshold[5]=2346 profile: FragThreshold[6]=2346 profile: FragThreshold[7]=2346 profile: FragThreshold[8]=2346 profile: FragThreshold[9]=2346 profile: FragThreshold[10]=2346 profile: FragThreshold[11]=2346 profile: FragThreshold[12]=2346 profile: FragThreshold[13]=2346 APEdca0 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca1 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 APEdca2 APEdca3 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 UAPSDCapable[0]=0 UAPSDCapable[1]=0 UAPSDCapable[2]=0 UAPSDCapable[3]=0 UAPSDCapable[4]=0 UAPSDCapable[5]=0 UAPSDCapable[6]=0 UAPSDCapable[7]=0 UAPSDCapable[8]=0 UAPSDCapable[9]=0 UAPSDCapable[10]=0 UAPSDCapable[11]=0 UAPSDCapable[12]=0 UAPSDCapable[13]=0 default ApCliUAPSDCapable[0]=0 default ApCliUAPSDCapable[1]=0 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[0] read_itxbf: MBSS[0] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[1] read_itxbf: MBSS[1] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[2] read_itxbf: MBSS[2] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[3] read_itxbf: MBSS[3] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[4] read_itxbf: MBSS[4] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[5] read_itxbf: MBSS[5] ITxBfEn = 0 read_itxbf: ITxBfEn = 0 read_itxbf: BSSID[6] read_itxbf: MBSS[6] ITxBfEn = 0 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[7] read_itxbf: MBSS[7] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[8] read_itxbf: MBSS[8] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[9] read_itxbf: MBSS[9] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[10] read_itxbf: MBSS[10] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[11] read_itxbf: MBSS[11] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[12] read_itxbf: MBSS[12] ITxBfEn = 1 read_itxbf: ITxBfEn = 1 read_itxbf: BSSID[13] read_itxbf: MBSS[13] ITxBfEn = 1 read_itxbf: Common.ITxBfEn = 1 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[0] read_etxbf: MBSS[0] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[1] read_etxbf: MBSS[1] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[2] read_etxbf: MBSS[2] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[3] read_etxbf: MBSS[3] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[4] read_etxbf: MBSS[4] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[5] read_etxbf: MBSS[5] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[6] read_etxbf: MBSS[6] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[7] read_etxbf: MBSS[7] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[8] read_etxbf: MBSS[8] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[9] read_etxbf: MBSS[9] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[10] read_etxbf: MBSS[10] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[11] read_etxbf: MBSS[11] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[12] read_etxbf: MBSS[12] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[13] read_etxbf: MBSS[13] ETxBfEnCond = 1 MBSS[0] MuOfdmaDlEnable = 1 MBSS[1] MuOfdmaDlEnable = 1 MBSS[2] MuOfdmaDlEnable = 1 MBSS[3] MuOfdmaDlEnable = 1 MBSS[4] MuOfdmaDlEnable = 1 MBSS[5] MuOfdmaDlEnable = 1 MBSS[6] MuOfdmaDlEnable = 1 MBSS[7] MuOfdmaDlEnable = 1 MBSS[8] MuOfdmaDlEnable = 1 MBSS[9] MuOfdmaDlEnable = 1 MBSS[10] MuOfdmaDlEnable = 1 MBSS[11] MuOfdmaDlEnable = 1 MBSS[12] MuOfdmaDlEnable = 1 MBSS[13] MuOfdmaDlEnable = 1 MBSS[0] MuOfdmaUlEnable = 1 MBSS[1] MuOfdmaUlEnable = 1 MBSS[2] MuOfdmaUlEnable = 1 MBSS[3] MuOfdmaUlEnable = 1 MBSS[4] MuOfdmaUlEnable = 1 MBSS[5] MuOfdmaUlEnable = 1 MBSS[6] MuOfdmaUlEnable = 1 MBSS[7] MuOfdmaUlEnable = 1 MBSS[8] MuOfdmaUlEnable = 1 MBSS[9] MuOfdmaUlEnable = 1 MBSS[10] MuOfdmaUlEnable = 1 MBSS[11] MuOfdmaUlEnable = 1 MBSS[12] MuOfdmaUlEnable = 1 MBSS[13] MuOfdmaUlEnable = 1 MBSS[0] MuMimoDlEnable = 1 MBSS[1] MuMimoDlEnable = 1 MBSS[2] MuMimoDlEnable = 1 MBSS[3] MuMimoDlEnable = 1 MBSS[4] MuMimoDlEnable = 1 MBSS[5] MuMimoDlEnable = 1 MBSS[6] MuMimoDlEnable = 1 MBSS[7] MuMimoDlEnable = 1 MBSS[8] MuMimoDlEnable = 1 MBSS[9] MuMimoDlEnable = 1 MBSS[10] MuMimoDlEnable = 1 MBSS[11] MuMimoDlEnable = 1 MBSS[12] MuMimoDlEnable = 1 MBSS[13] MuMimoDlEnable = 1 MBSS[0] MuMimoUlEnable = 1 MBSS[1] MuMimoUlEnable = 1 MBSS[2] MuMimoUlEnable = 1 MBSS[3] MuMimoUlEnable = 1 MBSS[4] MuMimoUlEnable = 1 MBSS[5] MuMimoUlEnable = 1 MBSS[6] MuMimoUlEnable = 1 MBSS[7] MuMimoUlEnable = 1 MBSS[8] MuMimoUlEnable = 1 MBSS[9] MuMimoUlEnable = 1 MBSS[10] MuMimoUlEnable = 1 MBSS[11] MuMimoUlEnable = 1 MBSS[12] MuMimoUlEnable = 1 MBSS[13] MuMimoUlEnable = 1 [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=1, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=2, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=3, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=4, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=5, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=6, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=7, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=8, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=9, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=10, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=11, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=12, Desired MFPC=0 [PMF]Set_PMFMFPC_Proc:: apidx=13, Desired MFPC=0 [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=1, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=2, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=3, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=4, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=5, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=6, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=7, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=8, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=9, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=10, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=11, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=12, Desired MFPR=0 [PMF]Set_PMFMFPR_Proc:: apidx=13, Desired MFPR=0 [PMF]Set_PMFSHA256_Proc:: apidx=0, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=1, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=2, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=3, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=4, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=5, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=6, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=7, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=8, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=9, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=10, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=11, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=12, Desired PMFSHA256=0 [PMF]Set_PMFSHA256_Proc:: apidx=13, Desired PMFSHA256=0 ReadMboParameterFromFile::(bMboEnable[0]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[1]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[2]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[3]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[4]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[5]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[6]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[7]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[8]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[9]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[10]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[11]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[12]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[13]=1, MboCapIndication = 0x40) ReadMboParameterFromFile::(bMboEnable[0]=1) ReadMboParameterFromFile::(bMboEnable[1]=1) MAP_MODE=3 ApCliEntry[0].Enable=0 ApCliEntry[1].Enable=0 IGMP deny list [0]-th entry =224.0.0.1 IGMP deny list [1]-th entry =224.0.0.2 IGMP deny list [2]-th entry =224.0.0.4 IGMP deny list [3]-th entry =224.0.0.5 IGMP deny list [4]-th entry =224.0.0.6 IGMP deny list [5]-th entry =224.0.0.7 IGMP deny list [6]-th entry =224.0.0.8 IGMP deny list [7]-th entry =224.0.0.9 IGMP deny list [8]-th entry =224.0.0.12 IGMP deny list [9]-th entry =224.0.0.16 IGMP deny list [10]-th entry =224.0.0.17 IGMP deny list [11]-th entry =224.0.0.22 IGMP deny list [12]-th entry =224.0.0.251 IGMP deny list [13]-th entry =224.0.0.252 IGMP deny list [14]-th entry =232.0.0.100 IGMP deny list [15]-th entry =239.255.12.42 IGMP deny list [16]-th entry =239.255.255.250 rtmp_read_wds_from_file(): WDS Profile WDS Number: band[0]=0, band[1]=0 WDS-Enable mode=0 WDS-Enable mode=0 HT_BAWinSize: wdev[0]: (TX=256, RX=256) HT_BAWinSize: wdev[1]: (TX=256, RX=256) HT_BAWinSize: wdev[2]: (TX=256, RX=256) HT_BAWinSize: wdev[3]: (TX=256, RX=256) HT_BAWinSize: wdev[4]: (TX=256, RX=256) HT_BAWinSize: wdev[5]: (TX=256, RX=256) HT_BAWinSize: wdev[6]: (TX=256, RX=256) HT_BAWinSize: wdev[7]: (TX=256, RX=256) HT_BAWinSize: wdev[8]: (TX=256, RX=256) HT_BAWinSize: wdev[9]: (TX=256, RX=256) HT_BAWinSize: wdev[10]: (TX=256, RX=256) HT_BAWinSize: wdev[11]: (TX=256, RX=256) HT_BAWinSize: wdev[12]: (TX=256, RX=256) HT_BAWinSize: wdev[13]: (TX=256, RX=256) HT: WDEV[0] Ext Channel = BELOW HT: WDEV[1] Ext Channel = BELOW HT: WDEV[2] Ext Channel = BELOW HT: WDEV[3] Ext Channel = BELOW HT: WDEV[4] Ext Channel = BELOW HT: WDEV[5] Ext Channel = BELOW HT: WDEV[6] Ext Channel = BELOW HT: WDEV[7] Ext Channel = BELOW HT: WDEV[8] Ext Channel = BELOW HT: WDEV[9] Ext Channel = BELOW HT: WDEV[a] Ext Channel = BELOW HT: WDEV[b] Ext Channel = BELOW HT: WDEV[c] Ext Channel = BELOW HT: WDEV[d] Ext Channel = BELOW 0:ra0 TWTsupport = 1 1:(null) TWTsupport = 1 2:(null) TWTsupport = 1 3:(null) TWTsupport = 1 4:(null) TWTsupport = 1 5:(null) TWTsupport = 1 6:(null) TWTsupport = 1 7:(null) TWTsupport = 1 8:(null) TWTsupport = 1 9:(null) TWTsupport = 1 10:(null) TWTsupport = 1 11:(null) TWTsupport = 1 12:(null) TWTsupport = 1 13:(null) TWTsupport = 1 rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect rtmp_read_wsc_user_parms: input parameter[WscDeviceName = AX1800 Dual Band Wi-Fi 6 GPON Router XX230v] incorrect pAd->reg_domain = 1 WtcSetMaxStaNum: MaxStaNum:224, BssidNum:14, WdsNum:16, MSTANum:1, MaxNumChipRept:32, MinMcastWcid:273 Top Init Done! Use dev_alloc_skb token_tx_queue_init(): ct sw token number = 1023 token_tx_queue_init(): token que inited done!id_head/tail=0/1024 token_tx_queue_init(): c7273004,c7273004 token_rx_init(): alloc mem for glb_var_wifi_rx_q_token_idx1. size:64*15360=983040 TxRing[0]: attr:0, total 2048 entry initialized TxRing[1]: attr:0, total 2048 entry initialized DriverModel=1 !!!! do phy and virtual address mapping dramBaEntry_pa=86e00000 PCIE Port0 link down [C0][NPU] npu_set_pcie_base, addr=200d4500, band_idx=0 [C0][npu_set_pcie_base] 2.4G pcieBase 200d4500 mem_base 200d4500, hw_rx_desc=0 PCIE Port1 link up [C0][NPU] npu_set_pcie_base, addr=200d4510, band_idx=1 [C0][npu_set_pcie_base] 5G pcieBase 200d4510 mem_base 200d4510, hw_rx_desc=0 [C0][NPU] npu_init... [C0]======================= [C0]NPU Version: MT7915D_NPU_V1.001.testv2 [C0]======================= [C0]Support NPU Wifi ffload [C0][NPU] pkt_queue_init... [C0]counter_init:0 [C0][NPU] Enter(2.4G) npu_npu_init_rxd, band_idx=0, rx_ring_size=1536 WIFI_MAIL_API_GET_WAIT_RXDESC_BASE info=1e806020 AllocSize 6000 AllocVa d5c90020, .AllocPa 1e806020 [C0][NPU] npu_init... [C0]======================= [C0]NPU Version: MT7915D_NPU_V1.001.testv2 [C0]======================= [C0]Support NPU Wifi ffload [C0][NPU] pkt_queue_init... [C0]counter_init:1 [C0][NPU] Enter npu_npu_init_rxd_5G, band_idx=1, rx_ring_size=1536 WIFI_MAIL_API_GET_WAIT_RXDESC_BASE info=1e800000 AllocSize 6000 AllocVa d5c94000, .AllocPa 1e800000 RX[2] DESC d1042000 size = 8192 RX[3] DESC d1045000 size = 16384 RX[4] DESC d104a000 size = 8192 register rx data done task cc601154 =====>register 2G hostdapt_registe_wifitask 0 =====>register 5G hostdapt_registe_wifitask 1 -->TX_RING_0[0xd7300]: Attr:0, Base=0x8c620000, Cnt=2048! -->TX_RING_1[0xd7310]: Attr:0, Base=0x8c628000, Cnt=2048! -->TX_RING_2[0xd5400]: Attr:3, Base=0x8c604000, Cnt=128! -->TX_RING_3[0xd5410]: Attr:2, Base=0x8c605000, Cnt=256! -->TX_RING_4[0xd5440]: Attr:1, Base=0x8c606000, Cnt=256! -->RX_RING_0[0xd4500]: Base=0x1e806020, Cnt=1536 -->RX_RING_1[0xd4510]: Base=0x1e800000, Cnt=1536 -->RX_RING_2[0xd5500]: Base=0x8c634000, Cnt=512 -->RX_RING_3[0xd7410]: Base=0x8c790000, Cnt=1024 -->RX_RING_4[0xd5520]: Base=0x8bda4000, Cnt=512 wdma_dma_ctrl(): WDMA_GLO_CFG=40000450 =========whnat_hal_wdma_init :ECNT WED_WDMA_CFG_BASE = 1fa00000 Hif Init Done! pci_driver_own_by_port: success to clear p=0 fw own, from(1): 1 is interrupt mode, 2 is polling mode. driver_own: port=1 is not enabled fw_prepare():using E2 ROM patch fw_prepare():using E2 RAM Parsing patch header Built date: 20230828104359a Platform: ALPS HW/SW version: 0x8a108a10 Patch version: 0xffffffff Section num: 0x2, subsys: 0x4 Section 0: type = 0x30002, offset = 0xe0, size = 0xfc90 Target address: 0x200000, length: 0xfc90 Section 1: type = 0x30002, offset = 0xfd70, size = 0x13730 Target address: 0xe000f000, length: 0x13730 Patch SEM Status = 2 patch is not ready && get semaphore success Start address = 0x200000, DL length = 64656, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0xe000f000, DL length = 79664, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdPatchFinishReq EventGenericEventHandler: CMD Success Patch SEM Status = 3 release patch semaphore WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 Parsing CPU 0 fw tailer Chip ID: 0x0b Eco version: 0x01 Region number: 0x07 Format version: 0x02 Format flag: 0x01 Ram version: ____000000 Built date: 20230828104432 Common crc: 0x68378479 Parsing tailer region 0 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x21fc00 Download size: 110592 Feature set: 0x20 Parsing tailer region 1 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x31dc00 Download size: 205824 Feature set: 0x00 Parsing tailer region 2 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x417400 Download size: 31744 Feature set: 0x00 Parsing tailer region 3 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0xe0022800 Download size: 411136 Feature set: 0x00 Parsing tailer region 4 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0xe0086e00 Download size: 332288 Feature set: 0x00 Parsing tailer region 5 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x23ac00 Download size: 87040 Feature set: 0x00 Parsing tailer region 6 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x400000 Download size: 81920 Feature set: 0x00 Release info: header tag = 0, total length = 64 tag 1, padding length = 2, tag length = 58 payload: t-neptune-mp-mt7915-2045-MT7915_MP_7_4_2045-20230828103801 Start address = 0x21fc00, DL length = 110592, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0x31dc00, DL length = 205824, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0x417400, DL length = 31744, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0xe0022800, DL length = 411136, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0xe0086e00, DL length = 332288, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0x23ac00, DL length = 87040, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0x400000, DL length = 81920, Data mode = 0x80000000 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 0x1, address = 0x21fc00 EventGenericEventHandler: CMD Success Parsing CPU 1 fw tailer Chip ID: 0x00 Eco version: 0x01 Region number: 0x03 Format version: 0x02 Format flag: 0x01 Ram version: DEV_000000 Built date: 20230828104451 Common crc: 0x6c78177a Parsing tailer region 0 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x10200000 Download size: 90032 Feature set: 0x00 Parsing tailer region 1 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0x10300000 Download size: 16592 Feature set: 0x00 Parsing tailer region 2 Decomp crc: 0x0 Decomp size: 0x0 Decomp block size: 0x0 Target address: 0xe0000000 Download size: 7648 Feature set: 0x00 Release info: header tag = 0, total length = 0 Start address = 0x10200000, DL length = 90032, Data mode = 0x80000010 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0x10300000, DL length = 16592, Data mode = 0x80000010 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) Start address = 0xe0000000, DL length = 7648, Data mode = 0x80000010 EventGenericEventHandler: CMD Success MtCmdAddressLenReq:(ret = 0) MtCmdFwStartReq: override = 0x4, address = 0x0 EventGenericEventHandler: CMD Success :MtCmdCr4Capability: option(0) MCU Init Done! efuse_probe: efuse = 10000012 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] rtmp_nv_init(): EEPROM Size[3584] flash_read(): read from address:0x120000, len:0xe00! [EEPROMImage - PreCalImageInfo - PreCalImage - TxDPDImage] [0xc99af000 - 0xc99afe00 - 0xc99afe10 - 0xc99bc220] validFlashEepromID(): eeFlashId=7915, pAd->ChipID=7915 [d-die version:1] [a-die version:2] NICReadEEPROMParameters: EEPROM 0x62 0 [37.454][cmm] 648: create dropbear RSA key success. [37.454][cmm] 655: start creating dropbear DSS key at CPU core 1. [37.454][cmm] 659: Try create dropbear DSS key loop=0 ... Generating 1024 bit dss key, this may take a while... [39.771][cmm] 671: create dropbear DSS key success. [39.771][cmm] 680: parent pid 860 [39.772][cmm] 688: parent pre cpu mask 00000001 [39.772][cmm] 702: parent post cpu mask 00000003 now bb MainSsid mac 8c:90:2d:06:a9:48 Country Region from e2p = 0 antenna_default_reset() todo antenna_default_reset() value = 0x5292, TxPath = 2, RxPath = 2 RTMPReadTxPwrPerRate(458): Don't Support this now! rc_radio_init(): DBDC MODE=1, ConcurrentBand=2 rc_radio_init(): radio_ctrl=cc609700,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf rc_radio_init(): radio_ctrl=cc609a58,Band=1,rfcap=3,channel=1,PhyMode=2 extCha=0xf ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 AntCfgInit(2918): Not support for HIF_MT yet! MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! MtReadPwrLimitTable: SKU Path: /var/Wireless/RT2860AP/mt7915-sku_2g.dat MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! MtReadPwrLimitTable: SKU Path: /var/Wireless/RT2860AP/mt7915-sku_5g.dat mt7915_check_RF_lock_down: RFlockDown Enable: 0 MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! MtReadPwrLimitTable: SKU Path: /var/Wireless/RT2860AP/mt7915-sku-bf_2g.dat MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!! MtReadPwrLimitTable: SKU Path: /var/Wireless/RT2860AP/mt7915-sku-bf_5g.dat mt7915_check_RF_lock_down: RFlockDown Enable: 0 EEPROM Init Done! mac_init()--> init_mac_cr()--> <--mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! BBPInit():BBP Initialization..... Band 0: valid=1, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 BBPInit() todo PHY Init Done! ch_switch_monitor_state_machine_init:: enter ch_switch_monitor_cfg_reset:: enter ch_switch_monitor_cfg_reset:: enter tx_pwr_comp_init():NotSupportYet! Set_SCSDefaultEnable(): BandIdx=0, SCSEnable=1 Set_SCSDefaultEnable(): BandIdx=1, SCSEnable=1 led_send_fw_cmd: 0205000000240000 led_0 map to gpio_18... led_send_fw_cmd: 0205010000340000 led_1 map to gpio_26... MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) ap_ftkd> Initialize FT KDP Module... Main bssid = 00:00:00:00:00:00 SetMuruPlatformTypeProc: param.ucPlatformType = 2 muru_cfg_dlul_limits:(Ret = 1 muru_cfg_dlul_limits:(Ret = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) <==== mt_wifi_init, Status=0 CmdHeraStbcPriorityCtrl: u1BandIdx=0, u1Operation=1, u1StbcPriority=0 CmdHeraStbcPriorityCtrl: u1BandIdx=1, u1Operation=1, u1StbcPriority=0 Register MBSSID IF 1 (ra1) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(1) Register MBSSID IF 2 (ra2) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(2) Register MBSSID IF 3 (ra3) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(3) Register MBSSID IF 4 (ra4) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(4) Register MBSSID IF 5 (ra5) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(5) Register MBSSID IF 6 (ra6) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(6) Register MBSSID IF 7 (rai0) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(7) Register MBSSID IF 8 (rai1) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(8) Register MBSSID IF 9 (rai2) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(9) Register MBSSID IF 10 (rai3) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(10) Register MBSSID IF 11 (rai4) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(11) Register MBSSID IF 12 (rai5) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(12) Register MBSSID IF 13 (rai6) wdev_init(caller:mbss_create_vif+0x194/0x4a4), wdev(13) MSTA_Init (2) ---> ApCli Register MSTA IF (apcli0) , pAd->MSTANum = 1 wdev_init(caller:MSTA_Init+0x200/0x650), wdev(14) Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=0, wdev_type=2 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=3 Register MSTA IF (apclii0) , pAd->MSTANum = 2 wdev_init(caller:MSTA_Init+0x200/0x650), wdev(15) Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=0, wdev_type=2 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=3 mt_service_init: wlan service inits successfully! WtcSetMaxStaNum: MaxStaNum:222, BssidNum:14, WdsNum:16, MSTANum:2, MaxNumChipRept:32, MinMcastWcid:272 RedInit: set CR4/N9 RED Enable to 1. RedInit: RED Initiailize Done. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. ==ecnt_wifi_rx_rps_hook=== RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 0 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 BuildChannelList() BandIdx = 0, PhyMode = 78, ChListNum = 13: phy_oper_init(): operate TxStream = 2, RxStream = 2 phy_freq_adjust : no prim_ch value for adjust! Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=0, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=0 AP inf up for ra_0(func_idx) OmacIdx=0 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) UpdateBeaconHandler, wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x110/0x464)!! mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=1, ctrl_ch2=0, cent_ch=1 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=1, ctrl_ch2=0, cent_ch=1, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=2, ctrl_ch2=0, cent_ch=2 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=2, ctrl_ch2=0, cent_ch=2, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=3, ctrl_ch2=0, cent_ch=3 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=3, ctrl_ch2=0, cent_ch=3, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=4, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=4, ctrl_ch2=0, cent_ch=4, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) EnableNF: mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=5, ctrl_ch2=0, cent_ch=5 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=5, ctrl_ch2=0, cent_ch=5, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=6, ctrl_ch2=0, cent_ch=6, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) Average Power WF0 WF1 WF2 WF3 -128 -128 -128 -128 mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=7, ctrl_ch2=0, cent_ch=7 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=7, ctrl_ch2=0, cent_ch=7, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=8, ctrl_ch2=0, cent_ch=8 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=8, ctrl_ch2=0, cent_ch=8, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) EnableNF: mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=9, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=9, ctrl_ch2=0, cent_ch=9, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=10, ctrl_ch2=0, cent_ch=10 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=10, ctrl_ch2=0, cent_ch=10, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=11, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=11, ctrl_ch2=0, cent_ch=11, RxPath=3, BandIdx=0, ChBand=0, BW=0,TXStream=2, RXStream=3, scan(1) UpdateBeaconHandler, wdev(0) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2c8/0x464)!! ==================================================================== Channel 1 : Busy Time = 11110, Skip Channel = FALSE, BwCap = TRUE Channel 2 : Busy Time = 10096, Skip Channel = FALSE, BwCap = TRUE Channel 3 : Busy Time = 6073, Skip Channel = FALSE, BwCap = TRUE Channel 4 : Busy Time = 6308, Skip Channel = FALSE, BwCap = TRUE Channel 5 : Busy Time = 8086, Skip Channel = FALSE, BwCap = TRUE Channel 6 : Busy Time = 7327, Skip Channel = FALSE, BwCap = TRUE Channel 7 : Busy Time = 9817, Skip Channel = FALSE, BwCap = TRUE Channel 8 : Busy Time = 11677, Skip Channel = FALSE, BwCap = TRUE Channel 9 : Busy Time = 14766, Skip Channel = FALSE, BwCap = TRUE Channel 10 : Busy Time = 15478, Skip Channel = FALSE, BwCap = TRUE Channel 11 : Busy Time = 5948, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 11 Rule 3 Channel Busy time value : Min Channel Busy = 5948 Rule 3 Channel Busy time value : BW = 20 [SelectClearChannelBusyTime] - band0 END ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 11, IsAband = 0 mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=11, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=1, TXStream=2, RXStream=2, scan(0) MtCmdSetTxRxPath: ctrl_chl=11, ctrl_ch2=0, cent_ch=9, RxPath=3, BandIdx=0, ChBand=0, BW=1,TXStream=2, RXStream=3, scan(0) zero_wait_dfs_switch_ch(): outband ch 0, ch_stat 0 ApAutoChannelAtBootUp<----------------- ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:0, CfgMode:177 [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(0) wifi_sys_linkup, wdev idx = 0 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[0]=0 wifi_sys_linkup:wdev(type=0,func_idx=1,wdev_idx=0),BssIndex(0) hw_ctrl_flow_v2_link_up: wdev_idx=0 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) Band0 BcnInitedRnd = 32 MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 0 for WscUUIDInit Generate UUID for apidx(0) WDS_Init(): wds_num(0) should be 4 of 2.4G WDS_Init(): wds_num(0) should be 4 of 5G WDS_Init():wds_num[0]=0, count=0, MAX_WDS_ENTRY=16, if_idx=0, flg_wds_init=0 Total allocated 0 WDS(es) for band0! ra4: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 4 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=4 AP inf up for ra_4(func_idx) OmacIdx=17 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) ap_run_at_boot() : ACS is disable !! ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:4, CfgMode:177 [PMF]APPMFInit:: apidx=4, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(4) wifi_sys_linkup, wdev idx = 4 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 LinkToOmacIdx = 11, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[4]=4 wifi_sys_linkup:wdev(type=4,func_idx=1,wdev_idx=4),BssIndex(1) hw_ctrl_flow_v2_link_up: wdev_idx=4 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (ra0) MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 4 for WscUUIDInit Generate UUID for apidx(4) ra5: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 5 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=5 AP inf up for ra_5(func_idx) OmacIdx=18 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[0] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) ap_run_at_boot() : ACS is disable !! ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:5, CfgMode:177 [PMF]APPMFInit:: apidx=5, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(5) wifi_sys_linkup, wdev idx = 5 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:285 for WDEV_TYPE:1 LinkToOmacIdx = 12, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[5]=5 wifi_sys_linkup:wdev(type=5,func_idx=1,wdev_idx=5),BssIndex(2) hw_ctrl_flow_v2_link_up: wdev_idx=5 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 12 (ra0) MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 0 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 5 for WscUUIDInit Generate UUID for apidx(5) Set_Map_Proc current MAP MODE is 3 Set_MapR2_Proc: MAP R2 is enabled Set_Bh_Bss_Proc ra0 bandIdx = 0 ,DevOwnRole 0x20 Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 Set_Fh_Bss_Proc ra4 wdev->MAPCfg.DevOwnRole 0x0 Set_Bh_Bss_Proc ra4 bandIdx = 0 ,DevOwnRole 0x44 Set_Fh_Bss_Proc ra5 wdev->MAPCfg.DevOwnRole 0x0 Set_Bh_Bss_Proc ra5 bandIdx = 0 ,DevOwnRole 0x48 rt28xx_ap_ioctl interface[ra6](index[6]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down rt28xx_ap_ioctl interface[ra6](index[6]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... rt28xx_ap_ioctl interface[apcli0](index[14]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down [47.163][cmm] 236 - ERROR: Get map shared buffer error. [47.163][cmm] 1156 - ERROR: Failed to attach map shared memory buffer. [47.164][cmm] 14353 - ERROR: There are no APDevices saved in map shared memory. [47.164][cmm] 17243 - ERROR: Can not find Controller cfg_mode=16 cfg_mode=16 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 BuildChannelList() BandIdx = 0, PhyMode = 78, ChListNum = 13: Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hc_radio_res_request(): wdev=1, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=2, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=3, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hc_radio_res_request(): wdev=6, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=14, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=2 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=2 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=3 SetEDCCAEnableCtrl: BandIdx = 0 set_vow_airtime_fairness_en: set 0. set_vow_dwrr_max_wait_time: set 1. SetPercentageCtrl: ucBandIdx = 0 SetPercentageCtrl: TxPowerPercentEn = 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 0 SetPowerDropCtrl: ucPowerDrop = 100 sync for : ra0 sync for : ra4 sync for : ra5 Set_FragThreshold_Proc::set wdev0 FragThreshold=2346) Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 device ra5 entered promiscuous mode br0: port 4(ra5) entered forwarding state br0: port 4(ra5) entered forwarding state device ra4 entered promiscuous mode br0: port 5(ra4) entered forwarding state br0: port 5(ra4) entered forwarding state can't add ra3 to bridge br0: Invalid argument can't add ra2 to bridge br0: Invalid argument can't add ra1 to bridge br0: Invalid argument device ra0 entered promiscuous mode br0: port 6(ra0) entered forwarding state br0: port 6(ra0) entered forwarding state device apcli0 entered promiscuous mode [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 0 ExtEventBeaconLostHandler::FW EVENT (8c:90:2d:06:a9:48), Reason 0x10 AP Beacon OFF!!! wifi_sys_linkdown:wdev(type=1,func_idx=0,wdev_idx=0),BssIndex(0) hw_ctrl_flow_v2_link_down: wdev_idx=0 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wmm_ctrl_release_entry(): Can't find HdevObj or Edca not required wifi_sys_close, wdev idx = 0 hw_ctrl_flow_v2_close: wdev_idx=0 wifi_sys_open(), wdev idx = 0 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=0 wifi_sys_linkup, wdev idx = 0 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:287 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[0]=0 wifi_sys_linkup:wdev(type=0,func_idx=1,wdev_idx=0),BssIndex(0) hw_ctrl_flow_v2_link_up: wdev_idx=0 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 ap_over_lapping_scan(), pAd->CommonCfg.bForty_Mhz_Intolerant:0, pAd->CommonCfg.bBssCoexEnable:0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 [PMF]APPMFInit:: apidx=4, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 4 wifi_sys_linkdown:wdev(type=1,func_idx=4,wdev_idx=4),BssIndex(1) hw_ctrl_flow_v2_link_down: wdev_idx=4 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close, wdev idx = 4 hw_ctrl_flow_v2_close: wdev_idx=4 wifi_sys_open(), wdev idx = 4 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=4 wifi_sys_linkup, wdev idx = 4 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:286 for WDEV_TYPE:1 LinkToOmacIdx = 11, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[4]=4 wifi_sys_linkup:wdev(type=4,func_idx=1,wdev_idx=4),BssIndex(1) hw_ctrl_flow_v2_link_up: wdev_idx=4 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 restart_ap, mbss_idx:4, BandIdx:0, reuse FallBack=0, bBssCoexEnable:0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 [PMF]APPMFInit:: apidx=5, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 5 wifi_sys_linkdown:wdev(type=1,func_idx=5,wdev_idx=5),BssIndex(2) hw_ctrl_flow_v2_link_down: wdev_idx=5 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close, wdev idx = 5 hw_ctrl_flow_v2_close: wdev_idx=5 wifi_sys_open(), wdev idx = 5 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=5 wifi_sys_linkup, wdev idx = 5 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:285 for WDEV_TYPE:1 LinkToOmacIdx = 12, LinkToWdevType = 1 TRTableInsertMcastEntry:band0 group_idx[5]=5 wifi_sys_linkup:wdev(type=5,func_idx=1,wdev_idx=5),BssIndex(2) hw_ctrl_flow_v2_link_up: wdev_idx=5 (bssUpdateChannel), ucPrimCh=11, ucCentChSeg0=9, ucCentChSeg1=0, BW=1, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 12 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 restart_ap, mbss_idx:5, BandIdx:0, reuse FallBack=0, bBssCoexEnable:0 Caller: SetCommonHT+0xb4/0x148 phy_mode=78, ch=11, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 rt28xx_ap_ioctl interface[apcli0](index[14]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down rt28xx_ap_ioctl interface[apcli0](index[14]) is down, cmd [8be2] return!!! WLAN-Start wlNetlinkTool Waiting for Wireless Events from interfaces... swWlanChkAhbErr: netlink to do Interface doesn't accept private ioctl... set (8BE2): Network is down SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 0, duty: 100 MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 0 MtCmdThermalProtectDutyCfg: duty: 100 SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 1, duty: 80 MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 1 MtCmdThermalProtectDutyCfg: duty: 80 SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 2, duty: 60 MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 2 MtCmdThermalProtectDutyCfg: duty: 60 SetThermalProtectDutyCfg(): band_idx: 0, level_idx: 3, duty: 20 MtCmdThermalProtectDutyCfg: band_idx: 0, level_idx: 3 MtCmdThermalProtectDutyCfg: duty: 20 SetThermalProtectEnable(): band_idx: 0, protection_type: 1, trigger_type: 1 SetThermalProtectEnable(): trigger_temp: 120, restore_temp: 114, recheck_time: 5 MtCmdThermalProtectEnable: band_idx: 0, protect_type: 1 MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 120 MtCmdThermalProtectEnable: restore_temp: 114, recheck_time: 5 rai0: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 7 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 BuildChannelList() BandIdx = 1, PhyMode = 177, ChListNum = 9: DfsBuildChannelList(): Done phy_oper_init(): operate TxStream = 2, RxStream = 2 [RadarStateCheck] RD_NORMAL_MODE phy_freq_adjust : no prim_ch value for adjust! Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=0, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=7 AP inf up for ra_7(func_idx) OmacIdx=0 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[1] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) [AutoChSelBuildChannelListFor5G] ChListNum5G = 9 UpdateBeaconHandler, wdev(7) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x110/0x464)!! mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=36, ctrl_ch2=0, cent_ch=36 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=36, ctrl_ch2=0, cent_ch=36, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=40, ctrl_ch2=0, cent_ch=40 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=40, ctrl_ch2=0, cent_ch=40, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=44, ctrl_ch2=0, cent_ch=44 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=44, ctrl_ch2=0, cent_ch=44, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=48, ctrl_ch2=0, cent_ch=48 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=48, ctrl_ch2=0, cent_ch=48, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=149, ctrl_ch2=0, cent_ch=149 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=149, ctrl_ch2=0, cent_ch=149, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=153, ctrl_ch2=0, cent_ch=153 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=153, ctrl_ch2=0, cent_ch=153, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=157, ctrl_ch2=0, cent_ch=157 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) sh: /usr/scriptMtCmdSetTxRxPath: ctrl_chl=157, ctrl_ch2=0, cent_ch=157, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) /usbhost_load.sh: not found mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=161, ctrl_ch2=0, cent_ch=161 DBDCIdx=1, ChBand=1, BW=0, TXStream=2, RXStream=2, scan(1) MtCmdSetTxRxPath: ctrl_chl=161, ctrl_ch2=0, cent_ch=161, RxPath=3, BandIdx=1, ChBand=1, BW=0,TXStream=2, RXStream=3, scan(1) UpdateBeaconHandler, wdev(7) bss not ready (state:0, caller:MTAPAutoSelectChannel+0x2c8/0x464)!! ==================================================================== Channel 36 : Busy Time = 1349, Skip Channel = FALSE, BwCap = TRUE Channel 40 : Busy Time = 0, Skip Channel = FALSE, BwCap = TRUE Channel 44 : Busy Time = 666, Skip Channel = FALSE, BwCap = TRUE Channel 48 : Busy Time = 1, Skip Channel = FALSE, BwCap = TRUE Channel 149 : Busy Time = 891, Skip Channel = FALSE, BwCap = TRUE Channel 153 : Busy Time = 2, Skip Channel = FALSE, BwCap = TRUE Channel 157 : Busy Time = 447, Skip Channel = FALSE, BwCap = TRUE Channel 161 : Busy Time = 845, Skip Channel = FALSE, BwCap = TRUE ==================================================================== Rule 3 Channel Busy time value : Select Primary Channel 153 Rule 3 Channel Busy time value : Min Channel Busy = 891 Rule 3 Channel Busy time value : BW = 80 [SelectClearChannelBusyTime] - band1 END ApAutoChannelAtBootUp : Auto channel selection: Selected channel = 153, IsAband = 1 [RadarStateCheck] RD_NORMAL_MODE mt7915_apply_dpd_flatness_data: eeprom 0x62 bit 0 is 0, do runtime cal MtCmdChannelSwitch: ctrl_chl=153, ctrl_ch2=0, cent_ch=155 DBDCIdx=1, ChBand=1, BW=2, TXStream=2, RXStream=2, scan(0) MtCmdSetTxRxPath: ctrl_chl=153, ctrl_ch2=0, cent_ch=155, RxPath=3, BandIdx=1, ChBand=1, BW=2,TXStream=2, RXStream=3, scan(0) DfsBuildChannelList(): Done zero_wait_dfs_switch_ch(): outband ch 0, ch_stat 0 ApAutoChannelAtBootUp<----------------- ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:7, CfgMode:78 [PMF]APPMFInit:: apidx=7, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(7) wifi_sys_linkup, wdev idx = 7 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:284 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[7]=7 wifi_sys_linkup:wdev(type=7,func_idx=1,wdev_idx=7),BssIndex(3) hw_ctrl_flow_v2_link_up: wdev_idx=7 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) Band1 BcnInitedRnd = 89 MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 1 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 7 for WscUUIDInit Generate UUID for apidx(7) WDS_Init(): wds_num(1) should be 4 of 2.4G WDS_Init(): wds_num(1) should be 4 of 5G WDS_Init():wds_num[1]=0, count=0, MAX_WDS_ENTRY=16, if_idx=0, flg_wds_init=0 Total allocated 0 WDS(es) for band1! rai4: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 11 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=11 AP inf up for ra_b(func_idx) OmacIdx=17 AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[1] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) ap_run_at_boot() : ACS is disable !! ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:11, CfgMode:78 [PMF]APPMFInit:: apidx=11, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(11) wifi_sys_linkup, wdev idx = 11 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:283 for WDEV_TYPE:1 LinkToOmacIdx = 11, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[11]=11 wifi_sys_linkup:wdev(type=11,func_idx=1,wdev_idx=11),BssIndex(4) hw_ctrl_flow_v2_link_up: wdev_idx=11 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (ra0) MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 1 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 11 for WscUUIDInit Generate UUID for apidx(11) rai5: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 12 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=12 AP inf up for ra_c(func_idx) OmacIdx=18 AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn mt7915 mtk_band_steering_netlink_init 243 band steering netlink init ok ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[1] = 1 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) ap_run_at_boot() : ACS is disable !! ===> APStartUpForMbss(caller:ap_inf_open+0x130/0x234), mbss_idx:12, CfgMode:78 [PMF]APPMFInit:: apidx=12, MFPC=0, MFPR=0, SHA256=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 ap_link_up(caller:APStartUpForMbss+0x42c/0x658), wdev(12) wifi_sys_linkup, wdev idx = 12 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:282 for WDEV_TYPE:1 LinkToOmacIdx = 12, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[12]=12 wifi_sys_linkup:wdev(type=12,func_idx=1,wdev_idx=12),BssIndex(5) hw_ctrl_flow_v2_link_up: wdev_idx=12 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 12 (ra0) MtCmdTxPowerSKUCtrl: tx_pwr_sku_en: 1, BandIdx: 1 MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1 set muru_update_he_cfg()!!!! PrintSrCmd: u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 PrintSrCmd: u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 PrintSrCmd: u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 apidx 12 for WscUUIDInit Generate UUID for apidx(12) Set_Map_Proc current MAP MODE is 3 Set_MapR2_Proc MAP R2 is already enabled Set_Bh_Bss_Proc rai0 bandIdx = 1 ,DevOwnRole 0x20 Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 Set_Fh_Bss_Proc rai4 wdev->MAPCfg.DevOwnRole 0x0 Set_Bh_Bss_Proc rai4 bandIdx = 1 ,DevOwnRole 0x44 Set_Fh_Bss_Proc rai5 wdev->MAPCfg.DevOwnRole 0x0 Set_Bh_Bss_Proc rai5 bandIdx = 1 ,DevOwnRole 0x48 rt28xx_ap_ioctl interface[rai6](index[13]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down rt28xx_ap_ioctl interface[rai6](index[13]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down rt28xx_ap_ioctl interface[apclii0](index[15]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down [52.648][cmm] 236 - ERROR: Get map shared buffer error. [52.649][cmm] 1156 - ERROR: Failed to attach map shared memory buffer. [52.649][cmm] 14353 - ERROR: There are no APDevices saved in map shared memory. [52.649][cmm] 17243 - ERROR: Can not find Controller cfg_mode=17 cfg_mode=17 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 BuildChannelList() BandIdx = 1, PhyMode = 177, ChListNum = 9: DfsBuildChannelList(): Done Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hc_radio_res_request(): wdev=8, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=9, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=10, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hc_radio_res_request(): wdev=13, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=0,ch_width=1,gf=0,sgi20=0,sgi40=0,tx_stbc=0,rx_stbc=0,amsdu_size=0 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=0 hc_radio_res_request(): wdev=15, hobj is not ready! Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=2 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=0, ampdu_factor=3 hc_radio_res_request(): wdev=8, hobj is not ready! hc_radio_res_request(): wdev=9, hobj is not ready! hc_radio_res_request(): wdev=10, hobj is not ready! hc_radio_res_request(): wdev=13, hobj is not ready! hc_radio_res_request(): wdev=15, hobj is not ready! set_vow_airtime_fairness_en: set 0. set_vow_dwrr_max_wait_time: set 1. SetPercentageCtrl: ucBandIdx = 1 SetPercentageCtrl: TxPowerPercentEn = 1 MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 1, BandIdx: 1 SetPowerDropCtrl: ucPowerDrop = 100 sync for : ra0 sync for : ra4 sync for : ra5 sync for : rai0 sync for : rai4 sync for : rai5 Set_FragThreshold_Proc::set wdev7 FragThreshold=2346) Caller: SetCommonHT+0xb4/0x148 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 device rai5 entered promiscuous mode br0: port 8(rai5) entered forwarding state br0: port 8(rai5) entered forwarding state device rai4 entered promiscuous mode br0: port 9(rai4) entered forwarding state br0: port 9(rai4) entered forwarding state can't add rai3 to bridge br0: Invalid argument can't add rai2 to bridge br0: Invalid argument can't add rai1 to bridge br0: Invalid argument device rai0 entered promiscuous mode br0: port 10(rai0) entered forwarding state br0: port 10(rai0) entered forwarding state device apclii0 entered promiscuous mode [PMF]APPMFInit:: apidx=7, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 7 ExtEventBeaconLostHandler::FW EVENT (8c:90:2d:06:a9:4a), Reason 0x10 AP Beacon OFF!!! wifi_sys_linkdown:wdev(type=1,func_idx=7,wdev_idx=7),BssIndex(3) hw_ctrl_flow_v2_link_down: wdev_idx=7 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wmm_ctrl_release_entry(): Can't find HdevObj or Edca not required wifi_sys_close, wdev idx = 7 hw_ctrl_flow_v2_close: wdev_idx=7 wifi_sys_open(), wdev idx = 7 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=7 wifi_sys_linkup, wdev idx = 7 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:284 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[7]=7 wifi_sys_linkup:wdev(type=7,func_idx=1,wdev_idx=7),BssIndex(3) hw_ctrl_flow_v2_link_up: wdev_idx=7 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 [PMF]APPMFInit:: apidx=11, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 11 wifi_sys_linkdown:wdev(type=1,func_idx=11,wdev_idx=11),BssIndex(4) hw_ctrl_flow_v2_link_down: wdev_idx=11 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close, wdev idx = 11 hw_ctrl_flow_v2_close: wdev_idx=11 wifi_sys_open(), wdev idx = 11 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=11 wifi_sys_linkup, wdev idx = 11 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:283 for WDEV_TYPE:1 LinkToOmacIdx = 11, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[11]=11 wifi_sys_linkup:wdev(type=11,func_idx=1,wdev_idx=11),BssIndex(4) hw_ctrl_flow_v2_link_up: wdev_idx=11 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 11 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 [PMF]APPMFInit:: apidx=12, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkdown(), wdev idx = 12 wifi_sys_linkdown:wdev(type=1,func_idx=12,wdev_idx=12),BssIndex(5) hw_ctrl_flow_v2_link_down: wdev_idx=12 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close, wdev idx = 12 hw_ctrl_flow_v2_close: wdev_idx=12 wifi_sys_open(), wdev idx = 12 ucAction = 0, ucBandIdx = 0, ucSmthIntlBypass = 0 ucAction = 0, ucBandIdx = 1, ucSmthIntlBypass = 0 phy_oper_init(): operate TxStream = 2, RxStream = 2 Caller: wlan_operate_init+0xbc/0x118 phy_mode=177, ch=153, wdev_type=1 ht_cap: ht_cap->HtCapInfo, ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap: ht_cap->HtCapParm, mdpu_density=5, ampdu_factor=3 hw_ctrl_flow_v2_open: wdev_idx=12 wifi_sys_linkup, wdev idx = 12 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:282 for WDEV_TYPE:1 LinkToOmacIdx = 12, LinkToWdevType = 1 TRTableInsertMcastEntry:band1 group_idx[12]=12 wifi_sys_linkup:wdev(type=12,func_idx=1,wdev_idx=12),BssIndex(5) hw_ctrl_flow_v2_link_up: wdev_idx=12 (bssUpdateChannel), ucPrimCh=153, ucCentChSeg0=155, ucCentChSeg1=0, BW=2, ucHetbRU26Disable=0, ucHetbAllDisable=1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8320, CmdBssInfoBmcRate.u2McTransmit = 8320 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 12 (ra0) bcn_buf_init():BcnPkt is allocated!, bcn offload=1 [54.155][cmm] 9189 - ERROR: wlNetlinkTool is already there. rt28xx_ap_ioctl interface[apclii0](index[15]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down rt28xx_ap_ioctl interface[apclii0](index[15]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down sh: can't open '/etc/smp.sh' SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 0, duty: 100 MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 0 MtCmdThermalProtectDutyCfg: duty: 100 SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 1, duty: 80 MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 1 MtCmdThermalProtectDutyCfg: duty: 80 SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 2, duty: 60 MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 2 MtCmdThermalProtectDutyCfg: duty: 60 SetThermalProtectDutyCfg(): band_idx: 1, level_idx: 3, duty: 20 MtCmdThermalProtectDutyCfg: band_idx: 1, level_idx: 3 MtCmdThermalProtectDutyCfg: duty: 20 SetThermalProtectEnable(): band_idx: 1, protection_type: 1, trigger_type: 1 SetThermalProtectEnable(): trigger_temp: 120, restore_temp: 114, recheck_time: 5 MtCmdThermalProtectEnable: band_idx: 1, protect_type: 1 MtCmdThermalProtectEnable: trigger_type: 1, trigger_temp: 120 MtCmdThermalProtectEnable: restore_temp: 114, recheck_time: 5 [54.332][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/ra1/brport/bridge/ifindex [54.334][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/rai1/brport/bridge/ifindex [54.336][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/ra2/brport/bridge/ifindex [54.338][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/ra3/brport/bridge/ifindex [54.340][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/rai2/brport/bridge/ifindex [54.342][cmm] 141 - ERROR: Stat sysfs for br port bridge ifindex failed, path: /sys/class/net/rai3/brport/bridge/ifindex rm: can't remove '/var/tmp/os_print/tpApp/2_debug': No such file or directory [54.559][cmm] 794: Skip create dropbear RSA key here [54.559][cmm] 822: Skip create dropbear DSS key here [2177] Mar 19 00:00:54 Running in background [Mar 19 00:00:54] radvd: poll error: Interrupted system call sendto: No such file or directory line(593) Msg.type(2030) pid(860) errno(2) ret(-1) iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/ppp/ppp_mppe.ko': No such file or directory ioctl set error: Inappropriate ioctl for device [55.187][cmm] 586 - ERROR: Gpon sn str:4D5354431BCA369A [55.187][cmm] 587 - ERROR: Gpon pwd str:0014678136 [55.187][cmm] 588 - ERROR: Gpon sn type:1 [55.187][cmm] 589 - ERROR: Gpon pwd type:0 api_set_sn_auth_info(564): passwd:(0014678136);0014678136 api_set_sn_auth_info(637): snIUint32[0] = 0x4d535443, snIUint32[1] = 0x1bca369a, vendor: 0x4d535443 [2024-3-19 Tue 00:00:54.997661][TP_omciMibReset][6430]:set OMCI machine in TP_omciMibReset api_renegotiate(780):api_renegotiate after MIB reset api_set_ctc_auth_info(649): -- not implemented, to do here! -- [55.270][cmm] 1177 - ERROR: Init loid tplink passwd tplink [55.299][cmm] 133 - ERROR: Cann't open file: /var/run/zebra.pid. [55.332][cmm] 133 - ERROR: Cann't open fik_domain: tplinkmodem.net le: /var/run/ripd.pid. [55.332][cmm] 133 - ERROR: Cann't open file: /var/run/ripngd.pid. [55.380][httpd] 1057 - ERROR: u_domain: tplinkmodem.net iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). nf_conntrack_rtsp v0.7 loading nf_nat_rtsp v0.7 loading ip6tables: Too many links. iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). [56.527][cmm] 222 - ERROR: vs record already exist [56.528][cmm] 222 - ERROR: vs record already exist [ rsl_initIqosObj ] 1248: 0#0,0,0,0 [56.559][cmm] 5449 - ERROR: Device.X_TP_Services.X_TP_VoiceService.{i}.PhyInterface.{i}. exit. skip create instance. writing RSA key killall: minidlnad: no process killed killall: vsftpd: no process killed [59.621][cmm] 1034 - ERROR: Can not find the sftp config file: /var/tmp/dconf/sftpcfg iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). [59.755][cmm] 1034 - ERROR: Can not find the sftp config file: /var/tmp/dconf/sftpcfg [2716] Mar 19 00:00:59 Failed listening on '22': Error listening: Address already in use Dropbear init failed, cos will restart it. [2024/03/19 00:00:59] getifaddr.c:334: runtime_vars.ifaces[0]=br0 [2716] Mar 19 00:00:59 Early exit: No listening ports available. [59.928][cmm] 1807 - ERROR: The lengh(0) of phone number() is less than 3 or lager than 32. [59.928][cmm] 1653 - ERROR: ret=9007 [59.928][cmm] 707 - ERROR: ret=9007 [59.930][cmm] 1807 - ERROR: The lengh(0) of phone number() is less than 3 or lager than 32. [59.930][cmm] 1653 - ERROR: ret=9007 [59.930][cmm] 707 - ERROR: ret=9007 [59.932][cmm] 1807 - ERROR: The lengh(0) of phone number() is less than 3 or lager than 32. [59.932][httpd] 529 - ERROR: Unknown page: /main/advanceLte.htm, skip it [59.932][cmm] 1653 - et_MapTS_Proc MAP TS is already disabled ;31mERROR: ret=9007 [59.932][httpd] 529 - ERROR: Unknown page: /main/sfpWan.htm, skip it [59.932][cmm] 707 - ERROR: ret=9007 [59.932][httpd] 529 - ERROR: UnknownSet_MapTS_Proc MAP TS is already disabled page: /main/sfpWanEdit.htm, skip it ++++++++++we are going to init cloud+++++++++++++++++ [59.970][cmm] 4364 - ERROR: mesh enable is 1, ts enable is 0 [59.970][cmm] 37Set_Map_Bh_Primary_Vid_Proc: ra5 default vid=4095 10 - ERROR: traffic separation is disabled rt28xx_ap_ioctl interface[apcli0](index[14]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down Set_Map_Fh_Vid_Proc: ra0 fh vid=4095 Set_Map_Bh_Primary_Vid_Proc: rai5 default vid=4095 rt28xx_ap_ioctl interface[apclii0](index[15]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set Set_Map_Fh_Vid_Proc: rai0 fh vid=4095 (8BE2): Network is down StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag ra0 Interface doesn't accept private ioctl... set (8BE2): Invalid argument rt28xx_ap_ioctl interface[apcli0](index[14]) is down, cmd [8be2] return!!! Interface doesn't accept private ioctl... set (8BE2): Network is down StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag ra0 mmmInit():Total mem size=51364, addr=0x0x1e78008. ************************************************************* *************************MMM TABLE DUMP********rt28xx_ap_ioctl interface[apclii0](index[15]) is down, cmd [8be2] return!!! ************** ------------------------------------------------------------- poolhead(40) poolnum dynamictimes chainhead poolend ------------------------------------------------------------- 0x1e78008 8 0 (nil) 0x1e848ac ------------------------------------------------------------- index poolhead(20) size blocks free usage ------------------------------------------------------------- 1 0x1e78030 32 256 256 0 2 0x1e7a448 64 128 128 0 3 0x1e7c660 128 64 64 0 4 0x1e7e778 256 32 32 0 5 0x1e80810 512 8 8 0 6 0x1e81848 1024 4 4 0 7 0x1e82870 2048 2 2 0 8 0x1e83890 4096 1 1 0 ------------------------------------------------------------- index chainnode(16) magic length prev next ------------------------------------------------------------- (nil) ************************************************************* 1710817259872|2734|4|cloud.c:91:main| - cloud-sdk version: 1.3.9-rc03, build_time:20211227_172322 Interface doesn't accept private ioctl... set (8BE2): Invalid argument Interface doesn't accept private ioctl... set (8BE2): Network is down ************************************************** ********************config dump******************* -------------------------------------------------- sef domain : n-deventry-gw.tplinkcloud.com sef port : 443 cloud svr default port : 443 default svr : n-devs-gw.tplinkcloud.com default port : 443 default valid time : 172800 heartbeat interval : 235000 request timeout : 5000 reconnect timewait max : 1024000 reconnect cachedsvr max times : 5 reconnect defaultsvr max times : 5 reconnect random time min : 2000 reconnect random time max : 256000 short connect interval : 259200000 max message number : 1000 max client number : 20 service file : /tmp/cloud_service.cfg cer file : /etc/cloud/2048_newroot.cer ssl verify CN : ssl verify time : 0 ************************************************** [60.250][cmm] 1807 - ERROR: The lengh(0) of phone number() is less than 3 or lager than 32. [60.250][cmm] 1653 - ERROR: ret=9007 [60.250][cmm] 707 - ERROR: ret=voip modules loaded, timer number 39007 [60.331][cmm] 1807 - ERROR: The lengh(0) of phone number() is less than 3 or l br0: port 1(eth0.1) entered disabled state ager than 32. [60.332][cmm] 1653 - ERROR: ret=9007 [60.332][cmm] 707 - ERROR: ret=9007 [60.338][cmm] 1807 - ERROR: The lengh(0) offxsGetLine(0)Ret[1]=State[3] phone number() is less than 3 or lager than 32. [60.338][cmm] 1653 -fxsSetLine[0]state 0x9 State UNKNOWN ! ERROR: ret=9007 [60.338][cmm] 707 - ERROR: ret=9007 [60.339][cmm] 18device eth0.1 left promiscuous mode br0: port 1(eth0.1) entered disabled state 07 - ERROR: The lengh(0) of phone number() is less than 3 or lager than 32. [60.339][cmm] 1653 - ERROR: ret=9007 [60.339][cmm] 707 - ERROR: ret=9007 [60.340][httpd] 659 - ERROR: Invalid value! [60.341][httpd] 529 - ERROR: Unknown page: /main/operateMode.htm, skip it [60.343][cmm] 1807 - ERRObr0: port 2(eth0.2) entered disabled state R: The lengh(0) of phone number() is less than 3 or lager than 32. [60.344][cmm] 1653 - ERROR: ret=9007 [60.344][cmm] 707 - ERROR: ret=9007 [60.364][cmm] 1387 - ERROR: --> device eth0.2 left promiscuous mode Xbr0: port 2(eth0.2) entered disabled state _TP_ConnType=LAN X_TP_ServiceType=Unknown [60.364][cmm] 1387 - ERROR: --> X_TP_ConnType=PPP3G X_TP_ServiceType=Unknown [60.364][cmm] 1387 - ERROR: --> X_TP_ConnType=DHCP4G X_TP_ServiceType=Unknown [60.364][cmm] 1387 - ERROR: --> X_TP_ConnType=PPPoE X_TP_ServiceType=Internet [60.365][cmm] 1387 - ERROR: --> X_TP_ConnType=PPPoE X_TP_ServiceType=Internet [60br0: port 3(eth0.3) entered disabled state .365][cmm] 1387 - ERROR: --> X_TP_ConnType=PPPoE X_TP_ServiceType=Internet sh: can't create /procdevice eth0.3 left promiscuous mode /br0: port 3(eth0.3) entered disabled state tplink/eth_forwa +++ timer 2 start (tick : 2) +++ rd: nonexistent directory *reg=00002104 value:00ff0000 *reg=00002204 value:00ff0000 *reg=00002304 value:00ff0000 *reg=00002404 value:00ff0000 VDSP_GetInstance:292 [GDI] Change log level to (EVA_LOG_ERR). ludewei get the ipv6 addr=:: ludewei get the ipv6 addr=:: ipv6 Via:0 zeroIp:1 zeroIp6:1 ipaddr:0.0.0.0 ip6addr::: [60.544][cutil] 2146 - ERROR: Error ip is 0.0.0.0,:: Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. device eth0.4 is not a slave of br0 device eth0 entered promiscuous mode Sbr0: port 1(eth0) entered forwarding state br0: port 1(eth0) entered forwarding state orry, rule does not exist. Illegal target name 'ieee1905'. Illegal target namfxsSetLine[0]state 0x9 State UNKNOWN ! e 'ieee1905'. sh: write error: Invalid argument device eth0 left promiscuous mode br0: port 1(eth0) entered disabled state device eth0.1 entered promiscuous mode br0: port 1(eth0.1) entered forwarding state br0: port 1(eth0.1) entered forwarding state device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode device eth0.4 is not a slave of br0 ath_band_steering_netlink_receive 157 pid = 2921 ath_band_steering_netlink_receive 157 pid = 2921 device eth0.5 is not a slave of br0 ath_band_steering_netlink_receive 157 pid = 2921 ath_band_steering_netlink_receive 157 pid = 2921 g_tx_ctl = 1 sh: write error: Invalid argument Starting daemon... [61.231][SharedLib] 123: Map shm size: 291864 bytes [61.232][SharedLib] 85: mac(8E:90:2D:06:A9:48), cfg_file(/var/tmp/map.conf), is_registrar(0), bMapController(0), mapEnable(1), vlan_enable(0) procName is sigma_dut, keyWord is [61.270][SharedLib] 123: Map shm size: 291864 bytes [61.272][SharedLib] 85: mac(8E:90:2D:06:A9:49), cfg_file(/var/tmp/map.conf), is_registrar(1), bMapController(1), mapEnable(1), vlan_enable(0) procName is sigma_dut, keyWord is [61.422][cmm] 1161 - ERROR: num of mapDevices is zero in memory buffer. [61.422][cmm] 1267 - EupdateDevBandWidthMac:index=0,d0:bf:9c:26:fa:65 RROR: There are no APDevices saved in map shared memory. [61.507][cmm] 14395 - ERROR: AgentOnController not found, update map device fail!!! sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) LoadClientCert: Not using a device certificate for connections sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) agentid is :USP::8C902D06A948 DM_EXEC_Main start DM_EXEC_EnableNotifications: 857 DM_EXEC_EnableNotifications: 860 Sending NotifyRequest (Event for path=Device.LocalAgent.Subscription.2) DEVICE_MQTT_QueueBinaryMessage: No internal MQTT connection matching Device.MQTT.Client.1 DM_EXEC_EnableNotifications: 864 sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) [61.570][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [61.570][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [61.570][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [61.570][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [61.571][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [61.571][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [61.571][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [61.571][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [61.572][cutil] 1918 - ERROR: Invalid DNS(2606:4700:4700::1111) or pUrl() [61.572][cutil] 1918 - ERROR: Invalid DNS(2001:4860:4860::8888) or pUrl() [61.572][cutil] 500 - ERROR: send DNS Query for domain(0.pool.ntp.org) fail, errno str: No such file or directory [61.572][cutil] 555 - ERROR: get ip for 0.pool.ntp.org failed [61.573][cutil] 500 - ERROR: send DNS Query for domain(0.pool.ntp.org) fail, errno str: No such file or directory [61.573][cutil] 555 - ERROR: get ip for 0.pool.ntp.org failed [61.573][cutil] 1998 - ERROR: Failed to sendto [61.574][cutil] 1998 - ERROR: Failed to sendto [61.574][cutil] 500 - ERROR: send DNS Query for domain(1.pool.ntp.org) fail, errno str: No such file or directory [61.574][cutil] 555 - ERROR: get ip for 1.pool.ntp.org failed [61.574][cutil] 500 - ERROR: send DNS Query for domain(1.pool.ntp.org) fail, errno str: No such file or directory [61.575][cutil] 555 - ERROR: get ip for 1.pool.ntp.org failed [61.575][cutil] 1998 - ERROR: Failed to sendto [61.575][cutil] 1998 - ERROR: Failed to sendto [61.576][cutil] 500 - ERROR: send DNS Query for domain(2.pool.ntp.org) fail, errno str: No such file or directory [61.576][cutil] 555 - ERROR: g [2024-3-19 Tue 00:01:01.496672]OMCI wait for RSL init done et ip fo [2024-3-19 Tue 00:01:01.502982][main][1165]:Enter OMCI State Machine, OMCI_STATE_START! r 2.pool.ntp.org failed [61.576][cutil] 500 - ERROR: send DNS Query for domain(2.pool.ntp.org) fail, errno str: No such file or directory [61.576][cutil] 555 - ERROR: get ip for 2.pool.ntp.org failed [61.577][cutil] 1998 - ERROR: Failed to sendto [61.577][cutil] 1998 - ERROR: Failed to sendto [61.577][cutil] 500 - ERROR: send DNS Query for domain(3.pool.ntp.org) fail, errno str: No such file or directory [61.578][cutil] 555 - ERROR: get ip for 3.pool.ntp.org failed [61.578][cutil] 500 - ERROR: send DNS Query for domain(3.pool.ntp.org) fail, errno str: No such file or directory [61.578][cutil] 555 - ERROR: get ip for 3.pool.ntp.org failed [61.578][cutil] 1998 - ERROR: Failed to sendto [61.579][cutil] 1998 - ERROR: Failed to sendto [61.579][cutil] 500 - ERROR: send DNS Query for domain(pool.ntp.or [2024-3-19 Tue 00:01:01.594196][omciAddVendorMeToStdMeTable][1199] before DM operation ,totalSize(4) g) fail, errno str: No such [2024-3-19 Tue 00:01:01.605766][omciAddVendorMeToStdMeTable][1250] toalTblSize(4) a/b (0) file or dir [2024-3-19 Tue 00:01:01.614961] initFilterMeInfo toalTblSize = 3 ectory [2024-3-19 Tue 00:01:01.621841] enter omciMeInitForCWMPConfigData [61. [2024-3-19 Tue 00:01:01.628710] enter omciMeInitForExtendOntG 579][ [2024-3-19 Tue 00:01:01.635303] enter omciMeInitForExtendOnt2Abi cutil] [2024-3-19 Tue 00:01:01.642283] enter omciMeInitForONTImageMode device lo entered promiscuous mode 555 [2024-3-19 Tue 00:01:01.652203] enter omciMeInitForExtendOnt3Abi - 2024-3-19 Tue 00:01:01.659022] enter omciMeInitForHuaweiProprietary 0;31m [2024-3-19 Tue 00:01:01.666199] enter omciMeInitForOntOpticalDat ERROR ue 00:01:01.673137] enter omciMeInitForHwExtendedWan [0m: [2024-3-19 Tue 00:01:01.679924] enter omciMeInitForStandard92Me get i [2024-3-19 Tue 00:01:01.686785] enter omciMeInitForExtend80211Mn p for [2024-3-19 Tue 00:01:01.693634] enter omciMeInitForVoipSoftwareI pool. [2024-3-19 Tue 00:01:01.700563] enter omciMeInitForExtOntProduct ntp.org [2024-3-19 Tue 00:01:01.707707][main][1183]:Enter OMCI State Machine, OMCI_STATE_START change to OMCI_STATE_IDLE! failed [2024-3-19 Tue 00:01:01.718833][omciInitCapability][539] omciInitCapability In sendto: [2024-3-19 Tue 00:01:01.726791]pPortList(48,248,47,47,47,47,32) No [2024-3-19 Tue 00:01:01.733161]pPort(48) such file or [2024-3-19 Tue 00:01:01.738100]pPort(248) dire [2024-3-19 Tue 00:01:01.742578]pPort(47) ctory [2024-3-19 Tue 00:01:01.746873]pPort(47) line [2024-3-19 Tue 00:01:01.751279]pPort(47) (593 [2024-3-19 Tue 00:01:01.755529]pPort(47) ) Msg [2024-3-19 Tue 00:01:01.759915]pPort(32) .type(9250 [2024-3-19 Tue 00:01:01.764673][omciInitCapability][640] getNext Dev2 currGponAuthObj SN(4D5354431BCA369A),SNtype(1) ) pid(860) [2024-3-19 Tue 00:01:01.776178][omciInitCapability][687] currOmciCapObj.vendorId IS (MSTC) errno(2) [2024-3-19 Tue 00:01:01.785214]read_flash:read In - 8 bytes in 66977792 ret(-1) [6 [2024-3-19 Tue 00:01:01.792875]read_flash:read In - 8 bytes in 66977792 1.580][cutil] 500 - ERROR: send DNS Query for d [2024-3-19 Tue 00:01:01.804724]read_flash:read In - 512 bytes in 1703936 omain(pool.n [2024-3-19 Tue 00:01:01.812463]read_flash:read In - 512 bytes in 33554432 tp.org) fail, errno str: No such file or directory [61.580][cutil] 555 - ERROR: get ip for pool.ntp.org failed [61.580][cutil] 1998 - ERROR: Failed [2024-3-19 Tue 00:01:01.834667]do not config omci intance by file info to sendto [61.581][cutil] 1998 - ERROR: Failed to sendto NTP server list: sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) M [2024-3-19 Tue 00:01:01.875518][main][1193]:Current State OMCI_STATE_IDLE, recv CONDITION_CFG_DONE change to OMCI_STATE_INIT! sg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or allocate buffer for epon_stat_prev. pon_mode = 0 directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pidset olt type: 0 (860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file ponTime:Connection Start working_mode: 10 or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: [2024-3-19 Tue 00:01:01.946823][main][1221]:Current State OMCI_STATE_INIT, recv CONDITION_ONU_READY change to OMCI_STATE_RUN! No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) [ omciAddVendorMeToStdMeTable ] 1216: 1#1 [ omciAddVendorMeToStdMeTable ] 1220: 2#1,1 [ omciAddVendorMeToStdMeTable ] 1216: 1#2 [ omciAddVendorMeToStdMeTable ] 1220: 2#2,1 [ omciAddVendorMeToStdMeTable ] 1216: 1#3 [ omciAddVendorMeToStdMeTable ] 1220: 2#3,1 [ omciAddVendorMeToStdMeTable ] 1216: 1#4 [ omciAddVendorMeToStdMeTable ] 1220: 2#4,1 sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) [62.042][mapAgent] 383: Starting map (AL MAC = 8e:90:2d:06:a9:48), mapEnable = 1... sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) [62.072][mapController] 387: Starting map (AL MAC = 8e:90:2d:06:a9:49), mapEnable = 1... [62.073][mapController] 9783: send stand renew to in band[0] [62.073][mapController] 9783: send stand renew to in band[1] sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) svchost_get_event_val: get param fail [0] sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) ctromfile.cfg [62.138][TP1905] 4875: Agent on controller [62.139][TP1905] 4875: Agent on controller sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) sendto: No such file or directory line(593) Msg.type(9250) pid(860) errno(2) ret(-1) ********************config dump******************* ----------------------status---------------------- processid : 2738 ---------------------configure-------------------- loglevel : 3 verify host : n-device-api.tplinkcloud.com verify port : 0 verify path : /v1/validate post connect timeout : 20 post transfer timeout : 20 get connect timeout : 20 get transfer timeout : 20 session debug : off cer file : /etc/cloud_https/2048new.cer cer type : ************************************************** [62.182][cos] 793 - ERROR: PON linkStatus changed :INIT->0 [62.182][cos] 872 - ERROR: PON linkStatus is not Stable (0) sh: /bin/mv: not found gpon flow open ioctl file fail Couldn't open image file: /tmp/tc_store_romfile.conf! [62.241][cmm] 14395 - ERROR: AgentOnController not found, update map device fail!!! [Mar 19 00:01:02] radvd: poll error: Interrupted system call Unlocking reservearea ... Could not open mtd device: reservearea Couldn't open image file: /tmp/tc_store_romfile.conf! [62.494][mapAgent] 4148: handleApAutoconfigurationResponse ####### selfDev profile:2, sendDev profile:2 [grpMgmtGenUpdateFeatureInfo:2607] Get commonToken failed! [grpMgmt_updateFeatureInfo:4746] Failed to generate update feature info message to cloud [grpMgmtGenUpdateFeatureInfo:2607] Get commonToken failed! [grpMgmt_updateFeatureInfo:4746] Failed to generate update feature info message to cloud [62.587][mapAgent] 4148: handleApAutoconfigurationResponse ####### selfDev profile:2, sendDev profile:2 [Mar 19 00:01:02] radvd: poll error: Interrupted system call sh: write error: Invalid argument [63.334][cmm] 14395 - ERROR: AgentOnController not found, update map device fail!!! [63.580][Topology] 3644 - ERROR: overrun timeStamp(0) [63.890][cos] 606 - ERROR: Dropbear error key, or can't listen to 22 port, will restart dropbear. [3227] Mar 19 00:01:03 Running in background [63.919][cos] 793 - ERROR: PON linkStatus changed :INIT->0 [63.919][cos] 797 - ERROR: PON linkStatus isStable (1) [63.930][cmm] 238 - ERROR: exit [63.930][cmm] 455 - ERROR: exit [65.788][cos] 1217: ===============================recv AgentConfig Message======================================== [65.789][cos] 1227: do not support autoconfig in Controller or easymesh disable [grpMgmtGenUpdateFeatureInfo:2607] Get commonToken failed! [grpMgmt_updateFeatureInfo:4746] Failed to generate update feature info message to cloud MacTableInsertEntry(): wcid 1 EntryType:0 ===== New Sta:fe:ee:58:07:a3:a4 wpa_check_rsn_cap : ocv support 0 wifi_sys_disconn_act: Not enqueue!! entry->EntryState=0 hw_ctrl_flow_v2_connt_act: wdev_idx=7 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag rai0 StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 hw_ctrl_flow_v2_peer_update: wdev_idx=7 set_muru_cert_muedca_override: override = 0 peer_reassoc_req: 35989 usec eapol_start: 1081 usec peer_msg2: 683 usec hw_ctrl_flow_v2_peer_update: wdev_idx=7 AP SETKEYS DONE(rai0) - AKMMap=WPA2PSK, PairwiseCipher=AES, GroupCipher=AES, wcid=1 from FE:EE:58:07:A3:A4 PTK:b265d0c1e959072d5a085702527ae06aa3792151c8fd03cc6cf49dc503d4e0be374c5d0b180852f1d0a3cbdbe8cc4d2fb84595a24e302eb31a4c7d50fcaa2d4f peer_msg4: 25084 usec pSsid=xx230v RRM_EnqueueNeighborRep() : send Neighbor RSP updateDevBandWidthMac:index=1,fe:ee:58:07:a3:a4 pSsid=xx230v RRM_EnqueueNeighborRep() : send Neighbor RSP [ check_and_ack ] 159: error, unknown check result yet for c0a80104 [ main ] 878: error, check and ack fail [ check_and_ack ] 159: error, unknown check result yet for c0a80104 [ main ] 878: error, check and ack fail MacTableDeleteEntry(caller:ap_peer_auth_req_at_idle_action+0x88c/0x15ec): wcid 1 ===== hw_ctrl_flow_v2_disconnt_act: wdev_idx=7 Del Sta:fe:ee:58:07:a3:a4 MacTableDeleteEntry 1730: call RtmpOSWrielessEventSendExt to send msg RT_WLAN_EVENT_EXPIRED MacTableInsertEntry(): wcid 1 EntryType:0 ===== New Sta:fe:ee:58:07:a3:a4 wpa_check_rsn_cap : ocv support 0 wifi_sys_disconn_act: Not enqueue!! entry->EntryState=0 hw_ctrl_flow_v2_connt_act: wdev_idx=0 StaRecUpdateTxProc(), set u4TxProcFlag = 0 to keep vlan tag ra0 StaRecUpdateWtbl: u2Tag=21,u2Length=8,ucEnVlan2Eth=1 hw_ctrl_flow_v2_peer_update: wdev_idx=0 set_muru_cert_muedca_override: override = 0 hwnat_clean_entry_by_dst_mac_hook fe:ee:58:07:a3:a4 peer_reassoc_req: 81361 usec eapol_start: 1082 usec peer_msg2: 708 usec hw_ctrl_flow_v2_peer_update: wdev_idx=0 AP SETKEYS DONE(ra0) - AKMMap=WPA2PSK, PairwiseCipher=AES, GroupCipher=AES, wcid=1 from FE:EE:58:07:A3:A4 PTK:6a84c1d47aa558bcafd95b49c7a4965be554ad4b59c81c9ef521b32e4263481a13b9d258a71b24fd393b5aa032431a42b9ffde7237108e217a078f4c462fe477 peer_msg4: 24852 usec pSsid=xx230v RRM_EnqueueNeighborRep() : send Neighbor RSP pSsid=xx230v RRM_EnqueueNeighborRep() : send Neighbor RSP

EN7523DRAMC V0.2 dram_type = 5, speed = 1866 Final Impdance Cal Result: OCDP:0x1b, OCDN:0x1b, ODTP:0xa, ODTN:0xa DDR1866 PLL setting init [Dramc] PCDDR3 AC Timing update Fire MRW command... ModeReg.2, value.0x20 done Fire MRW command... ModeReg.3, value.0x0 done Fire MRW command... ModeReg.1, value.0x6 done Fire MRW command... ModeReg.0, value.0x1114 done Fire MRW command... ModeReg.1, value.0x86 done Fire MRW command... ModeReg.1, value.0x6 done Calculate size. DRAM size=256MB U-Boot 2014.04-rc1 (Mar 19 2024 - 09:12:08) DRAM: 240 MiB EN7529CT Now running in RAM - U-Boot at: 8edff000 spi_nand_probe: mfr_id=0xc8, dev_id=0x1 Using Flash ECC. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_F50L1G41LB, Flash Size=0x8000000 bmt pool size: 81 BMT & BBT Init Success In: serial Out: serial Err: serial CPU0: found redistributor 0 region 0:8ee3d988 Net: ecnt_eth Uip activated use flash mac: D8:44:89:BD:CF:D8 Not found TC Phy Not found TC Phy Not found TC Phy Not found TC Phy [ CPEinit ] 465: CPE init [ cp_initCommProto ] 277: g_commProtoConfig.myMac: d8:44:89:bd:cf:d8 Boot flag csum incorrect, return image0 [ os_initCPEInfo ] 297: hw ver: XX230v v1.0 00000000 [ os_initCPEInfo ] 298: sw ver: 0.16.0 3.0.0 v6066 [ os_initCPEInfo ] 305: sn: 22445J1001433 [ os_initCPEInfo ] 308: pin: 18909296 [ os_initCPEInfo ] 315: endian: 0 [ os_initCPEInfo ] 318: acFlag: 0 [ CPEinit ] 489: CPE is idle Hit any key to stop autoboot: 0 Boot flag csum incorrect, return image0 Prepare to boot image0 Boot flag csum incorrect, return image0 Ok bootm flag=0, states=70f ## Loading kernel from FIT Image at 81800200 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-6.12.65 Type: Kernel Image Compression: lzma compressed Data Start: 0x818002e4 Data Size: 3794794 Bytes = 3.6 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: 02e3505a Hash algo: sha1 Hash value: 71e50f818f2bf4a69d873b0dba103cb195f78c3d ## Loading fdt from FIT Image at 81800200 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM OpenWrt tplink_xx230v device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x81b9eb88 Data Size: 15994 Bytes = 15.6 KiB Architecture: ARM Hash algo: crc32 Hash value: 32ad634f Hash algo: sha1 Hash value: e3f70422e5c0438fedcb90e431961fbe664fd0ae Booting using the fdt blob at 0x81b9eb88 Uncompressing Kernel Image ... OK reserving fdt memory region: addr=80000000 size=200000 Loading Device Tree to 8cdf0000, end 8cdf6e79 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.12.65 (sirherobrine23@matheus-note) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 14.3.0 r32493-8d680de76a) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Thu Jan 15 01:43:31 2026 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TP-Link xx230v [ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000 [ 0.000000] earlycon: ns16550 at MMIO32 0x1fbf0000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080200000-0x000000008fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080200000-0x0000000083ffffff] [ 0.000000] node 0: [mem 0x0000000084000000-0x00000000840fffff] [ 0.000000] node 0: [mem 0x0000000084100000-0x0000000086ffffff] [ 0.000000] node 0: [mem 0x0000000087000000-0x0000000089ffffff] [ 0.000000] node 0: [mem 0x000000008a000000-0x000000008fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000008fffffff] [ 0.000000] On node 0, zone Normal: 512 pages in unavailable ranges [ 0.000000] OF: reserved mem: 0x80000000..0x801fffff (2048 KiB) nomap non-reusable atf@80000000 [ 0.000000] OF: reserved mem: 0x84000000..0x840fffff (1024 KiB) nomap non-reusable npu_binary@84000000 [ 0.000000] OF: reserved mem: 0x87000000..0x88ffffff (32768 KiB) nomap non-reusable qdma0-buf@87000000 [ 0.000000] OF: reserved mem: 0x89000000..0x89ffffff (16384 KiB) nomap non-reusable qdma1-buf@89000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 14 pages/cpu s25100 r8192 d24052 u57344 [ 0.000000] Kernel command line: sdram_conf=0x00108893 vendor_name=ECONET Technologies Corp. product_name=xPON ONU ethaddr=D8:44:89:BD:CF:D8 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 username=telecomadmin password=nE7jA%5m dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=33 root=/dev/mtdblock5 ro console=ttyS0,115200n8 earlycon bootflag=0 serdes_sel=0 [ 0.000000] Unknown kernel command line parameters "Technologies ONU sdram_conf=0x00108893 vendor_name=ECONET product_name=xPON ethaddr=D8:44:89:BD:CF:D8 snmp_sysobjid=1.2.3.4.5 country_code=ff ether_gpio=0c power_gpio=1515 username=telecomadmin password=nE7jA%5m dsl_gpio=0b internet_gpio=02 multi_upgrade_gpio=0b020400000000000000000000000000 onu_type=2 qdma_init=33 bootflag=0 serdes_sel=0", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: GICD_CTRL.DS=0, SCR_EL3.FIQ=0 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x09080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns [ 0.000001] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns [ 0.008800] Switching to timer-based delay loop, resolution 40ns [ 0.015561] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000) [ 0.026949] CPU: Testing write buffer coherency: ok [ 0.032333] pid_max: default: 32768 minimum: 301 [ 0.044606] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.052659] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.064342] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.071560] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.078918] rcu: Hierarchical SRCU implementation. [ 0.084189] rcu: Max phase no-delay instances is 1000. [ 0.090210] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.099414] smp: Bringing up secondary CPUs ... [ 0.119476] GICv3: CPU1: found redistributor 1 region 0:0x090a0000 [ 0.119532] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.119677] smp: Brought up 1 node, 2 CPUs [ 0.137184] SMP: Total of 2 processors activated (100.00 BogoMIPS). [ 0.144083] CPU: All CPU(s) started in SVC mode. [ 0.149623] Memory: 194132K/260096K available (7827K kernel code, 601K rwdata, 2052K rodata, 1024K init, 220K bss, 64992K reserved, 0K cma-reserved) [ 0.169019] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.179889] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.191008] pinctrl core: initialized pinctrl subsystem [ 0.198658] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.205714] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.214023] thermal_sys: Registered thermal governor 'step_wise' [ 0.214103] cpuidle: using governor menu [ 0.226254] debugfs: Directory '1fa20000.system-controller' with parent 'regmap' already present! [ 0.237120] /pcie@1fa91000: Fixed dependency cycle(s) with /pcie@1fa91000/interrupt-controller [ 0.247001] /pcie@1fa92000: Fixed dependency cycle(s) with /pcie@1fa92000/interrupt-controller [ 0.267178] SCSI subsystem initialized [ 0.271519] usbcore: registered new interface driver usbfs [ 0.277643] usbcore: registered new interface driver hub [ 0.283513] usbcore: registered new device driver usb [ 0.289229] Advanced Linux Sound Architecture Driver Initialized. [ 0.297616] clocksource: Switched to clocksource arch_sys_counter [ 0.310876] NET: Registered PF_INET protocol family [ 0.316439] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.325109] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.334371] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.342895] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.351339] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.359240] TCP: Hash tables configured (established 2048 bind 2048) [ 0.366621] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.374853] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.382064] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.390190] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.396441] PCI: CLS 0 bytes, default 64 [ 0.402475] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.411508] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.417965] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.433858] mtk-pcie 1fa91000.pcie: host bridge /pcie@1fa91000 ranges: [ 0.441146] mtk-pcie 1fa91000.pcie: MEM 0x0020000000..0x0021ffffff -> 0x0020000000 [ 1.037606] mtk-pcie 1fa91000.pcie: Port0 link down [ 1.043266] mtk-pcie 1fa91000.pcie: PCI host bridge to bus 0000:00 [ 1.050128] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.056163] pci_bus 0000:00: root bus resource [mem 0x20000000-0x21ffffff] [ 1.064848] PCI: bus0: Fast back to back transfers enabled [ 1.070907] pci_bus 0000:00: resource 4 [mem 0x20000000-0x21ffffff] [ 1.078118] mtk-pcie 1fa92000.pcie: host bridge /pcie@1fa92000 ranges: [ 1.085315] mtk-pcie 1fa92000.pcie: MEM 0x0022000000..0x0023ffffff -> 0x0022000000 [ 1.616094] mtk-pcie 1fa92000.pcie: PCI host bridge to bus 0001:00 [ 1.622948] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.629019] pci_bus 0001:00: root bus resource [mem 0x22000000-0x23ffffff] [ 1.636897] pci 0001:00:01.0: [14c3:0811] type 01 class 0x060400 PCIe Root Port [ 1.645139] pci 0001:00:01.0: BAR 0: can't handle BAR larger than 4GB (size 0x200000000) [ 1.654044] pci 0001:00:01.0: BAR 0 [mem size 0x00000001 64bit pref disabled] [ 1.661974] pci 0001:00:01.0: PCI bridge to [bus 00] [ 1.667495] pci 0001:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.677290] PCI: bus0: Fast back to back transfers disabled [ 1.683481] pci 0001:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.692986] pci 0001:01:00.0: [14c3:7915] type 00 class 0x000280 PCIe Endpoint [ 1.701139] pci 0001:01:00.0: BAR 0 [mem 0x00000000-0x000fffff 64bit pref] [ 1.708829] pci 0001:01:00.0: BAR 2 [mem 0x00000000-0x00003fff 64bit pref] [ 1.716495] pci 0001:01:00.0: BAR 4 [mem 0x00000000-0x00000fff 64bit pref] [ 1.724808] pci 0001:01:00.0: supports D1 D2 [ 1.729517] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.737130] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0001:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.754159] PCI: bus1: Fast back to back transfers disabled [ 1.760322] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.767668] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff]: assigned [ 1.775892] pci 0001:00:01.0: BAR 0 [mem 0x22200000 64bit pref disabled]: assigned [ 1.784272] pci 0001:00:01.0: BAR 0: error updating (0x2220000c != 0x0000000c) [ 1.792259] pci 0001:01:00.0: BAR 0 [mem 0x22000000-0x220fffff 64bit pref]: assigned [ 1.800861] pci 0001:01:00.0: BAR 2 [mem 0x22100000-0x22103fff 64bit pref]: assigned [ 1.809463] pci 0001:01:00.0: BAR 4 [mem 0x22104000-0x22104fff 64bit pref]: assigned [ 1.818063] pci 0001:00:01.0: PCI bridge to [bus 01] [ 1.823547] pci 0001:00:01.0: bridge window [mem 0x22000000-0x221fffff] [ 1.831081] pci_bus 0001:00: resource 4 [mem 0x22000000-0x23ffffff] [ 1.837979] pci_bus 0001:01: resource 1 [mem 0x22000000-0x221fffff] [ 1.845097] pcieport 0001:00:01.0: enabling device (0140 -> 0142) [ 1.852562] pcieport 0001:00:01.0: PME: Signaling with IRQ 31 [ 1.860434] airoha_hsdma 1fa01800.hsdma: Airoha HSDMA driver registered [ 1.868229] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.876177] printk: legacy console [ttyS0] disabled [ 1.882047] 1fbf0000.serial: ttyS0 at MMIO 0x1fbf0000 (irq = 33, base_baud = 115200) is a 16550 [ 1.891680] printk: legacy console [ttyS0] enabled [ 1.891680] printk: legacy console [ttyS0] enabled [ 1.901797] printk: legacy bootconsole [ns16550] disabled [ 1.901797] printk: legacy bootconsole [ns16550] disabled [ 1.915837] spi-nand spi0.0: ESMT SPI NAND was found. [ 1.920990] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 1.929532] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.935915] Creating 7 MTD partitions on "spi0.0": [ 1.940752] 0x000000000000-0x000000080000 : "bootloader" [ 1.948139] 0x000000080000-0x000000120000 : "romfile" [ 1.955134] 0x0000000a0000-0x000000240000 : "misc" [ 1.963266] 0x0000001a0000-0x0000011a0000 : "kernel" [ 2.002174] 0x0000011a0000-0x0000011a0001 : "rootfs_dummy" [ 2.008530] 0x0000011a0000-0x000007500000 : "rootfs" [ 2.227126] mtd: setting mtd5 (rootfs) as root device [ 2.232586] 1 squashfs-split partitions found on MTD device rootfs [ 2.238813] 0x000002180000-0x000007500000 : "rootfs_data" [ 2.245368] 0x000007500000-0x000008000000 : "reserved_bmt" [ 2.361447] airoha-npu 1e900000.npu: L2C sram size: 0x00 [ 2.366779] airoha-npu 1e900000.npu: FPGA Stage: 1 [ 2.373344] airoha-npu 1e900000.npu: Direct firmware load for airoha/en7523_npu_rv32.bin failed with error -2 [ 2.383322] airoha-npu 1e900000.npu: Falling back to sysfs fallback for: airoha/en7523_npu_rv32.bin [ 64.572215] airoha-usb-phy 1fad0000.phy: Frequency not detected, using default SR calibration. [ 64.585429] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 64.590709] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 1 [ 64.602072] xhci-mtk 1fab0000.usb: hcc params 0x01400f98 hci version 0x110 quirks 0x0000000000200010 [ 64.611296] xhci-mtk 1fab0000.usb: irq 45, io mem 0x1fab0000 [ 64.617125] xhci-mtk 1fab0000.usb: xHCI Host Controller [ 64.622434] xhci-mtk 1fab0000.usb: new USB bus registered, assigned bus number 2 [ 64.629866] xhci-mtk 1fab0000.usb: Host supports USB 3.2 Enhanced SuperSpeed [ 64.637706] hub 1-0:1.0: USB hub found [ 64.641683] hub 1-0:1.0: 2 ports detected [ 64.646489] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 64.655318] hub 2-0:1.0: USB hub found [ 64.659205] hub 2-0:1.0: 1 port detected [ 64.664003] i2c-mt7621 1fbf8000.i2c0: clock 100 kHz [ 64.669337] airoha-thermal 1efbd000.thermal-sensor: EN7523: IC calibrated (pdid:3, pkg:3) [ 64.677651] airoha-thermal 1efbd000.thermal-sensor: EN7523: Init check code_30:32008, Slope:1750 [ 64.698786] en7523-audio 1fbe2200.audio-controller: mtk_afe_combine_sub_dai(), num of dai 2 [ 64.707556] debugfs: Directory '1fbe2200.audio-controller' with parent 'en7523-i2s' already present! [ 64.718526] NET: Registered PF_INET6 protocol family [ 64.725038] Segment Routing with IPv6 [ 64.728834] In-situ OAM (IOAM) with IPv6 [ 64.732850] NET: Registered PF_PACKET protocol family [ 64.738253] 8021q: 802.1Q VLAN Support v1.8 [ 64.742799] Registering SWP/SWPB emulation handler [ 64.777017] mt7530-mmio 1fb58000.switch: configuring for fixed/internal link mode [ 64.784726] mt7530-mmio 1fb58000.switch lan1 (uninitialized): PHY [mt7530-0:09] driver [Airoha EN7523 PHY] (irq=POLL) [ 64.796391] mt7530-mmio 1fb58000.switch lan2 (uninitialized): PHY [mt7530-0:0a] driver [Airoha EN7523 PHY] (irq=POLL) [ 64.808012] mt7530-mmio 1fb58000.switch lan3 (uninitialized): PHY [mt7530-0:0b] driver [Airoha EN7523 PHY] (irq=POLL) [ 64.819527] mt7530-mmio 1fb58000.switch wan (uninitialized): PHY [mt7530-0:0c] driver [Airoha EN7523 PHY] (irq=POLL) [ 64.831018] airoha_eth 1fb50000.ethernet eth0: entered promiscuous mode [ 64.837785] DSA: tree 0 setup [ 64.841206] airoha-npu 1e900000.npu: L2C sram size: 0x00 [ 64.846536] airoha-npu 1e900000.npu: FPGA Stage: 1 [ 64.851677] mt7530-mmio 1fb58000.switch: Link is Up - 10Gbps/Full - flow control rx/tx [ 64.857687] airoha-npu 1e900000.npu: Direct firmware load for airoha/en7523_npu_rv32.bin failed with error -2 [ 64.869591] airoha-npu 1e900000.npu: Falling back to sysfs fallback for: airoha/en7523_npu_rv32.bin [ 125.998226] airoha-npu 1e900000.npu: L2C sram size: 0x00 [ 126.003558] airoha-npu 1e900000.npu: FPGA Stage: 1 [ 126.008625] airoha-npu 1e900000.npu: Direct firmware load for airoha/en7523_npu_rv32.bin failed with error -2 [ 126.018596] airoha-npu 1e900000.npu: Falling back to sysfs fallback for: airoha/en7523_npu_rv32.bin [ 187.438226] clk: Disabling unused clocks [ 187.442177] PM: genpd: Disabling unused power domains [ 187.447230] ALSA device list: [ 187.450275] #0: en7523-i2s [ 187.453598] mtdblock: MTD device 'rootfs' is NAND, please consider using UBI block devices instead. [ 187.470789] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 187.478992] Freeing unused kernel image (initmem) memory: 1024K [ 187.485173] Run /sbin/init as init process [ 188.212981] init: Console is alive [ 188.216635] init: - watchdog - [ 189.342170] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 189.407720] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 189.415912] airoha-npu 1e900000.npu: L2C sram size: 0x00 [ 189.421289] airoha-npu 1e900000.npu: FPGA Stage: 1 [ 189.443688] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 189.463014] init: - preinit - [C0]core freq at 333000000 Hz [C0]timer_init: Timer clk is running at 32 Mhz [C0]wcid_counter_init:0 [C0]wcid_counter_init:1 [C0][NPU] ba_node_init... [C0]baNode_array_init [C0]counter_init:2 [C0][NPU] queue_mutex_init... [C0]qdma_init [C1]core1_main [C2]timer_isr Store Value 1e903000, val[C2]core2_main Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 192.607613] random: crng init done [ 193.063424] jffs2: notice: (597) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (0 unchecked, 1 orphan) and 8 of xref (1 dead, 0 orphan) found. [ 193.084871] mount_root: switching to jffs2 overlay [ 193.102864] overlayfs: upper fs does not support tmpfile. [ 193.143359] urandom-seed: Seeding with /etc/urandom.seed [ 193.335373] procd: - early - [ 193.338533] procd: - watchdog - [ 193.941546] procd: - watchdog - [ 193.945313] procd: - ubus - [ 194.102206] procd: - init - Please press Enter to activate this console. [ 195.051272] kmodloader: loading kernel modules from /etc/modules.d/* [ 195.431880] i2c_dev: i2c /dev entries driver [ 195.448308] Loading modules backported from Linux version v6.18-0-g7d0a66e4b [ 195.455380] Backport generated by backports.git 4d44cef [ 195.556652] urngd: v1.0.2 started. [ 195.557711] xt_time: kernel timezone is -0000 [ 195.932486] mt7915e 0001:01:00.0: enabling device (0140 -> 0142) [ 196.192487] mt7915e 0001:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20240429200716a [ 196.192487] [ 196.531805] mt7915e 0001:01:00.0: WM Firmware Version: ____000000, Build Time: 20240429200752 [ 196.559912] mt7915e 0001:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20240429200812 [ 196.678255] mt7915e 0001:01:00.0: registering led 'mt76-phy0' [ 196.741698] mt7915e 0001:01:00.0: registering led 'mt76-phy1' [ 196.844971] PPP generic driver version 2.4.2 [ 196.855094] NET: Registered PF_PPPOX protocol family [ 196.864716] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. [ 196.872669] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved. [ 196.928582] kmodloader: done loading kernel modules from /etc/modules.d/* [ 206.481105] mt7530-mmio 1fb58000.switch lan1: configuring for phy/internal link mode [ 206.491711] br-lan: port 1(lan1) entered blocking state [ 206.496976] br-lan: port 1(lan1) entered disabled state [ 206.502354] mt7530-mmio 1fb58000.switch lan1: entered allmulticast mode [ 206.509049] airoha_eth 1fb50000.ethernet eth0: entered allmulticast mode [ 206.516138] mt7530-mmio 1fb58000.switch lan1: entered promiscuous mode [ 206.564115] mt7530-mmio 1fb58000.switch lan2: configuring for phy/internal link mode [ 206.577888] br-lan: port 2(lan2) entered blocking state [ 206.583140] br-lan: port 2(lan2) entered disabled state [ 206.588531] mt7530-mmio 1fb58000.switch lan2: entered allmulticast mode [ 206.595491] mt7530-mmio 1fb58000.switch lan2: entered promiscuous mode [ 206.643251] mt7530-mmio 1fb58000.switch lan3: configuring for phy/internal link mode [ 206.654742] br-lan: port 3(lan3) entered blocking state [ 206.660124] br-lan: port 3(lan3) entered disabled state [ 206.665463] mt7530-mmio 1fb58000.switch lan3: entered allmulticast mode [ 206.672510] mt7530-mmio 1fb58000.switch lan3: entered promiscuous mode [ 206.743420] mt7530-mmio 1fb58000.switch wan: configuring for phy/internal link mode [ 207.579743] br-lan: port 4(phy0-ap0) entered blocking state [ 207.585355] br-lan: port 4(phy0-ap0) entered disabled state [ 207.591087] mt7915e 0001:01:00.0 phy0-ap0: entered allmulticast mode [ 207.597786] mt7915e 0001:01:00.0 phy0-ap0: entered promiscuous mode [ 207.669777] br-lan: port 4(phy0-ap0) entered blocking state [ 207.675399] br-lan: port 4(phy0-ap0) entered forwarding state [ 207.682340] mt7915e 0001:01:00.0 phy0-ap0: left allmulticast mode [ 207.688606] mt7915e 0001:01:00.0 phy0-ap0: left promiscuous mode [ 207.694766] br-lan: port 4(phy0-ap0) entered disabled state [ 207.739608] br-lan: port 4(phy0-ap0) entered blocking state [ 207.745216] br-lan: port 4(phy0-ap0) entered disabled state [ 207.750965] mt7915e 0001:01:00.0 phy0-ap0: entered allmulticast mode [ 207.757654] mt7915e 0001:01:00.0 phy0-ap0: entered promiscuous mode [ 208.374754] br-lan: port 5(phy1-ap0) entered blocking state [ 208.380444] br-lan: port 5(phy1-ap0) entered disabled state [ 208.386129] mt7915e 0001:01:00.0 phy1-ap0: entered allmulticast mode [ 208.392916] mt7915e 0001:01:00.0 phy1-ap0: entered promiscuous mode [ 208.485730] br-lan: port 5(phy1-ap0) entered blocking state [ 208.491380] br-lan: port 5(phy1-ap0) entered forwarding state [ 208.497886] mt7915e 0001:01:00.0 phy1-ap0: left allmulticast mode [ 208.504017] mt7915e 0001:01:00.0 phy1-ap0: left promiscuous mode [ 208.510176] br-lan: port 5(phy1-ap0) entered disabled state [ 208.592234] br-lan: port 5(phy1-ap0) entered blocking state [ 208.597912] br-lan: port 5(phy1-ap0) entered disabled state [ 208.603591] mt7915e 0001:01:00.0 phy1-ap0: entered allmulticast mode [ 208.610391] mt7915e 0001:01:00.0 phy1-ap0: entered promiscuous mode [ 210.799181] mt7530-mmio 1fb58000.switch lan3: Link is Up - 1Gbps/Full - flow control rx/tx [ 210.808490] br-lan: port 3(lan3) entered blocking state [ 210.813736] br-lan: port 3(lan3) entered forwarding state [ 210.879058] mt7530-mmio 1fb58000.switch wan: Link is Up - 1Gbps/Full - flow control rx [ 212.102538] br-lan: port 5(phy1-ap0) entered blocking state [ 212.108173] br-lan: port 5(phy1-ap0) entered forwarding state [ 215.774875] br-lan: port 4(phy0-ap0) entered blocking state [ 215.780543] br-lan: port 4(phy0-ap0) entered forwarding state