TP-Link X80-5G V1

X80-5G

The TP-Link Deco X80-5G is a dual port router with a built in 5g modem and a phone port.

  • Dual-Band Wi-Fi 6.
  • Dual Eithernet ports 1× 2.5 Gbps port and 1× Gigabit
  • VoLTE/VoIP POTS telephony Support.
  • Based on the Qualcomm IPQ8074A SoC, AP-HK01-C1 reference design.
  • 5G mm wave Modem based on the Snapdragon X55 5G Modem-RF System with theoretical 10 Gbps Peak download and 3.5 Gbps peak upload speeds.
  • Dual firmware with U-boot HTTP based recovery.

Manufacture info:

https://www.tp-link.com/us/deco-mesh-wifi/product-family/deco-x80-5g/

https://www.qualcomm.com/news/releases/2024/02/qualcomm-unveils-the-world-s-most-advanced-5g-modem-rf-system--h

https://www.qualcomm.com/products/technology/modems/snapdragon-x80-5g-modem-rf-system

GPL source:

https://static.tp-link.com/upload/gpl-code/2024/202404/20240423/X80-5G.tar

https://www.tp-link.com/en/support/download/deco-x80-5g/#GPL-Code

Not supported.

Operwrt:
OEM:

note: the OEM image has been patched to bypass root password with added dropbear support for interactive shell)

CPU Ram (DDR3) Flash (Nand) Network WLAN 2.5G WLAN 5G Mobile VoLTE/IP Telephony Serial
IPQ8074A @2.2ghz 512MB (4Gbit) 128MB (1Gbit) 2 B/G/N/AX A/N/AC/AX 5G/ 4.5gLTE RJ11 POTS Yes
  1. Download and copy the initramfs image to your PC's TFTP server folder.
  2. connect up your serial port and set up a connection with a terminal program such as SmarTTY
  3. Plug the router into your computer using an ethernet cable
  4. set your pc's IP address to the below settings:
  5. static 192.168.1.2.
  6. power the router and quickly type the magic string “tpl” and press enter to break into u-boot
  7. in the shell set the environment variables to enable tftpbooting
  8. setenv ipaddr 192.168.1.1
  9. setenv serverip 192.168.1.2
  10. In the shell run the below command to initiate the image transfer:
  11. this will load your image to memory as location 044000000 in ram
  12. tftpboot 0x44000000 192.168.1.2:openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
  13. your image will now upload to your ram ready to boot.
  14. run (bootm) and your image will now load.
  1. Download a copy of the factory.ubi to your pc
  2. set up a ssh/scp session to your router with a program such as SmarTTY.
  3. upload the factory.ubi to /tmp on your router
  4. in the console run the below command:
  5. ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
  6. wait for it to complete and reboot your router.

The Deco X80-5G has HTTP Uboot Method for recovering the device. The official guide can be found here: https://www.tp-link.com/en/support/faq/2958/

Firstly download your firmware to your PC Set a static IP address and netmask of 192.168.0.2/255.255.255.0 on your Ethernet port on your PC.

Connect the PC directly to the ethernet port of the Deco unit.

Use a pin/pen to press and hold the reset button and plug power into the device. On the PC, access http://192.168.0.1, you would be able to see the firmware recovery page. Select your previously downloaded firmware and recovery will start. After a while your device will reboot, and it will be back to stock.

Failsafe mode can be invoked by halting the boot process from a serial connection.

Firstly connect a serial device and set up a connection. Watch the boot log waiting for the Failsafe prompt and press f and then enter you will be presented with the below:

================= FAILSAFE MODE active ================
special commands:
* firstboot          reset settings to factory defaults
* mount_root     mount root-partition with config files

after mount_root:
* passwd                         change root's password
* /etc/config               directory with config files

for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe

The TP-Link X80-5G has the following buttons:

BUTTON Event
Reset reset/ recover
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
dev:    size   erasesize  name
mtd0: 00100000 00020000 "0:SBL1"
mtd1: 00100000 00020000 "0:MIBIB"
mtd2: 00080000 00020000 "0:BOOTCONFIG"
mtd3: 00080000 00020000 "0:BOOTCONFIG1"
mtd4: 00300000 00020000 "0:QSEE"
mtd5: 00080000 00020000 "0:DEVCFG"
mtd6: 00080000 00020000 "0:APDP"
mtd7: 00080000 00020000 "0:RPM"
mtd8: 00080000 00020000 "0:CDT"
mtd9: 00180000 00020000 "0:APPSBLENV"
mtd10: 00200000 00020000 "0:APPSBL"
mtd11: 00080000 00020000 "0:ART"
mtd12: 02a00000 00020000 "rootfs"
mtd13: 02a00000 00020000 "rootfs_1"
mtd14: 00080000 00020000 "0:ETHPHYFW"
mtd15: 00900000 00020000 "factory_data"
mtd16: 01100000 00020000 "runtime_data"
mtd17: 00573000 0001f000 "kernel"
mtd18: 01341000 0001f000 "ubi_rootfs"

Back ports

Bottom and label

PCB's

It has a top cover you pry off to see the fan which exposes four screws two for each clam shell o part of the case.
Underneath it has four rubber feet with screws beneath I just forced my screw-driver through the rubber pad to save removing them.
With all 8 screws removed you may split off both sides of the shell.
On the side of the shell with the RGB info LED it has a small PCB with a harness with a push in connector that needs removing on the bottom of the device before separating.
At this point you have enough to expose the serial UART and I really would not recommend you proceed any further.
To completely disassemble the device, one must unsolder at least one of the two antennas labeled 1 and 2 and slide the PCB up from the top fan assembly.
Behind the antennas 1 and 2 is 2 screws to remove the fan assembly.
once the fan assembly is lifted up you can unplug the fan connector to remove it.
You then can start to separate the two PCB's of the device there is there is 14 IPEX/ U.FL connectors 8 for the WIFI and 8 for the LTE, They are all labeled on the PCB and the antennas.
All the U.Fl cables are secured with spring clips and tape and plastic hooks I'd recommend you take pictures as it was a pain to work out how to route them to get it together again.
With all the antenna connectors unplugged you can then remove the screws holding the heatsinks PCB's and antenna Frames.
NOTE all the screws are of different lengths make sure to note their location for reassembly.
Separating the two halves this will expose the bottom 2 cover screws to remove the base.

Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labeled TP1 TP2 and TP3.

I soldered a standard pin header to the test pads but be aware it is very fragile and would be easy to rip them off by accident but seems sturdy with TP3 being on a ground plane.

Green is Ground (TP3) Yellow is RX (TP2) Orange is TX (TP1)

                        R (~5k Ohms)     -------------
                     /---\/\/\/`--VCC----| USB FTDI  |
  -----------        |                   | 1.8V      |
  |TP2|---RX----ora--+----------- TX-----|           | --> to PC (minicom, screen, C-Kermit, putty ...)
  |TP1|---TX----yel-------------- RX-----|           |
  |TP3|---GND---gre-------------- GND----|           |
  -----------                            -------------
Serial connection parameters
for TP-Link X80-5G V1
115200, 8N1, 1.8V
CR(/r) line ending format
Uboot Magic string
(password)
tpl (enter)

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158 S - IMAGE_VARIANT_STRING=HAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e5 B - 201 - PBL, Start B - 2736 - bootable_media_detect_entry, Start B - 3444 - bootable_media_detect_success, Start B - 3448 - elf_loader_entry, Start B - 6116 - auth_hash_seg_entry, Start B - 6359 - auth_hash_seg_exit, Start B - 68381 - elf_segs_hash_verify_entry, Start B - 131223 - PBL, End B - 142282 - SBL1, Start B - 194132 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 200598 - pm_device_init, Start B - 321714 - PM_SET_VAL:Skip D - 120658 - pm_device_init, Delta B - 324123 - pm_driver_init, Start D - 5368 - pm_driver_init, Delta B - 330498 - clock_init, Start D - 2135 - clock_init, Delta B - 334432 - boot_flash_init, Start D - 12566 - boot_flash_init, Delta B - 350780 - boot_config_data_table_init, Start D - 3111 - boot_config_data_table_init, Delta - (575 Bytes) B - 358283 - Boot Setting : 0x00000618 B - 362187 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:4,Subtype:0 B - 369111 - sbl1_ddr_set_params, Start B - 372923 - CPR configuration: 0x30c B - 376278 - cpr_init, Start B - 379176 - Rail:0 Mode: 5 Voltage: 792000 B - 384269 - CL CPR settled at 744000mV B - 387106 - Rail:1 Mode: 5 Voltage: 880000 B - 391376 - Rail:1 Mode: 7 Voltage: 888000 D - 16531 - cpr_init, Delta B - 398177 - Pre_DDR_clock_init, Start B - 402264 - Pre_DDR_clock_init, End B - 405589 - DDR Type : PCDDR3 B - 411323 - do ddr sanity test, Start D - 1067 - do ddr sanity test, Delta B - 416081 - DDR: Start of HAL DDR Boot Training B - 420808 - DDR: End of HAL DDR Boot Training B - 426512 - DDR: Checksum to be stored on flash is 1377291785 B - 436821 - Image Load, Start D - 224327 - QSEE Image Loaded, Delta - (1376448 Bytes) B - 661240 - Image Load, Start D - 61 - SEC Image Loaded, Delta - (0 Bytes) B - 668926 - Image Load, Start D - 10705 - DEVCFG Image Loaded, Delta - (26008 Bytes) B - 679723 - Image Load, Start D - 22051 - RPM Image Loaded, Delta - (86584 Bytes) B - 701866 - Image Load, Start D - 108976 - APPSBL Image Loaded, Delta - (672668 Bytes) B - 810964 - QSEE Execution, Start D - 61 - QSEE Execution, Delta B - 816759 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 823164 - SBL1, End D - 683170 - SBL1, Delta S - Flash Throughput, 6745 KB/s (2162955 Bytes, 320641 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 1651 MHz U-Boot 2016.01 (Feb 25 2021 - 20:16:45 +0800) DRAM: smem ram ptable found: ver: 1 len: 4 1 GiB NAND: Could not find nand_gpio in dts, using defaults ONFI device found ID = 158061c8 Vendor = c8 Device = 61 SF: Unsupported flash IDs: manuf 00, jedec 1c78, ext_jedec 4a74 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: <NULL>: 0 PCI0 is not defined in the device tree PCI1 is not defined in the device tree In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 machid: 8010400 Card did not respond to voltage select! eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid eth2 MAC Address from ART is not valid eth3 MAC Address from ART is not valid eth4 MAC Address from ART is not valid eth5 MAC Address from ART is not valid gpio 38 set BOARD_3V9_5V_EN_GPIO to high[1] gpio 64 set PHY_QCA8081_1V8_EN_GPIO to high[1] gpio 33 set PHY_AR8033_3V3_EN_GPIO to high[1] gpio 35 set ONOFF_MODULE_5G_GPIO to low[0] ... 1s gpio 35 set ONOFF_MODULE_5G_GPIO to high[1] ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 9 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1097309032 ubi0: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20 Find no boot alter flag! Enter magic string to stop autoboot in?Unmounting UBIFS volume ubi_factory_data! ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 42 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 273099923 ubi0: available PEBs: 108, total reserved PEBs: 228, PEBs reserved for bad PEB handling: 20 Read 0 bytes from volume kernel to 44000000 No size specified -> Using max size (5713920) ## Loading kernel from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 3857929 Bytes = 3.7 MiB Architecture: AArch64 OS: Linux Load Address: 0x41080000 Entry Point: 0x41080000 Hash algo: crc32 Hash value: db19bb74 Hash algo: sha1 Hash value: 80e8e02e244a73839be2d7cb2a6f845e49cb0cc8 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'fdt@hk01.c5' fdt subimage Description: ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x443d8698 Data Size: 92380 Bytes = 90.2 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 3f191698 Hash algo: sha1 Hash value: d0cbc4e75fecf605333dd4a95c21ed37d26c3df4 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x443d8698 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3e6000, end 4a3ff8db ... OK Could not find PCI in device tree Using machid 0x8010400 from environment Starting kernel ... Jumping to AARCH64 kernel via monitor [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.60 (tplink@linuxci2-sp) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 34c568b+r49254) ) #1 SMP PREEMPT Mon Apr 10 21:40:48 CST 2023 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Ignoring memory range 0x40000000 - 0x41000000 [ 0.000000] Machine: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C5 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: OVERLAP DETECTED! [ 0.000000] wifi_dump@51100000 (0x0000000051100000--0x0000000051700000) overlaps with wigig_dump@51300000 (0x0000000051300000--0x0000000051700000) [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc03ef43000 s19328 r8192 d29824 u57344 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 22503 6 [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashf s rootwait swiotlb=1 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] software IO TLB [mem 0x7fd3c000-0x7fd7c000] (0MB) mapped at [ffffffc03ed3c 000-ffffffc03ed7bfff] [ 0.000000] Memory: 886388K/914432K available (5258K kernel code, 609K rwdata, 2292K r odata, 220K init, 466K bss, 28044K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum ) [ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc1000000 ( 15 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc03f000000 ( 1008 MB) [ 0.000000] .init : 0xffffffc0007e2000 - 0xffffffc000819000 ( 220 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0007e1844 ( 7559 KB) [ 0.000000] .data : 0xffffffc000828000 - 0xffffffc0008c0400 ( 609 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987 e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078n s [ 0.000508] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000520] pid_max: default: 32768 minimum: 301 [ 0.000612] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000622] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes) [ 0.001283] EFI services will not be available. [ 0.001308] ASID allocator initialised with 65536 entries [ 0.051933] MSM Memory Dump base table set up [ 0.051954] MSM Memory Dump apps data table set up [ 0.090039] Detected VIPT I-cache on CPU1 [ 0.090083] CPU1: Booted secondary processor [410fd034] [ 0.120022] Detected VIPT I-cache on CPU2 [ 0.120049] CPU2: Booted secondary processor [410fd034] [ 0.150051] Detected VIPT I-cache on CPU3 [ 0.150077] CPU3: Booted secondary processor [410fd034] [ 0.150126] Brought up 4 CPUs [ 0.150153] SMP: Total of 4 processors activated. [ 0.150163] CPU: All CPU(s) started at EL1 [ 0.150186] alternatives: patching kernel code [ 0.169584] DMI not present or invalid. [ 0.169818] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns : 19112604462750000 ns [ 0.169842] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.170038] pinctrl core: initialized pinctrl subsystem [ 0.171151] NET: Registered protocol family 16 [ 0.199989] cpuidle: using governor ladder [ 0.230004] cpuidle: using governor menu [ 0.230210] NET: Registered protocol family 42 [ 0.230287] vdso: 2 pages (1 code @ ffffffc00082d000, 1 data @ ffffffc00082c000) [ 0.230398] DMA: preallocated 256 KiB pool for atomic allocations [ 0.230527] CPU: IPQ8074A, SoC Version: 2.0 [ 0.230949] IPC logging disabled [ 0.230955] IPC logging disabled [ 0.230960] IPC logging disabled [ 0.230964] IPC logging disabled [ 0.230969] IPC logging disabled [ 0.233206] Soc version is not 1, changing clock offsets [ 0.241895] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.244585] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.247995] sps:sps is ready. [ 0.254986] spmi spmi-0: PMIC Arb Version-2 (0x20010000) [ 0.262935] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.263195] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2 [ 0.301899] pps_core: LinuxPPS API ver. 1 registered [ 0.301906] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giom etti@linux.it> [ 0.301928] PTP clock support registered [ 0.302077] dmi: Firmware registration failed. [ 0.303583] Advanced Linux Sound Architecture Driver Initialized. [ 0.304211] clocksource: Switched to clocksource arch_sys_counter [ 0.307322] NET: Registered protocol family 2 [ 0.307883] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.307991] TCP bind hash table entries: 8192 (order: 5, 131072 bytes) [ 0.308176] TCP: Hash tables configured (established 8192 bind 8192) [ 0.308228] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.308265] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.308437] NET: Registered protocol family 1 [ 0.315795] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.315812] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 20 01-2006 Red Hat, Inc. [ 0.319103] Key type asymmetric registered [ 0.319118] Asymmetric key parser 'x509' registered [ 0.319146] io scheduler noop registered [ 0.319159] io scheduler deadline registered (default) [ 0.321544] 20000000.pci supply vdda not found, using dummy regulator [ 0.321590] 20000000.pci supply vdda_phy not found, using dummy regulator [ 0.321627] 20000000.pci supply vdda_refclk not found, using dummy regulator [ 0.322590] PCI host bridge /soc/pci@20000000 ranges: [ 0.322618] IO 0x20200000..0x2020ffff -> 0x20200000 [ 0.322633] MEM 0x20220000..0x2fffffff -> 0x20220000 [ 0.565748] qcom-pcie 20000000.pci: link up [ 0.565895] qcom-pcie 20000000.pci: PCI host bridge to bus 0000:00 [ 0.565908] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.565921] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0x202 00000-0x2020ffff]) [ 0.565931] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff] [ 0.566250] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfigurin g [ 0.567232] pci 0000:00:00.0: BAR 8: assigned [mem 0x20300000-0x204fffff] [ 0.567248] pci 0000:00:00.0: BAR 9: assigned [mem 0x20500000-0x206fffff 64bit pref] [ 0.567261] pci 0000:00:00.0: BAR 0: assigned [mem 0x20220000-0x20220fff 64bit] [ 0.567277] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] [ 0.567292] pci 0000:01:00.0: BAR 0: assigned [mem 0x20300000-0x20300fff 64bit] [ 0.567344] pci 0000:01:00.0: BAR 2: assigned [mem 0x20301000-0x20301fff 64bit] [ 0.567393] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.567403] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 0.567415] pci 0000:00:00.0: bridge window [mem 0x20300000-0x204fffff] [ 0.567425] pci 0000:00:00.0: bridge window [mem 0x20500000-0x206fffff 64bit pref] [ 0.567478] PCIe: RC0 enabled during bootup [ 0.567892] MDSS QPIC HW Base phy_Address=0x7980000 virt=ffffff80004c0000 [ 0.568265] mdss_qpic_panel_probe: Panel Name = qpic lcd panel [ 0.569465] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully! [ 0.573296] msm_rpm_log_probe: OK [ 0.573645] msm-dcc b3000.dcc: DCC XPU is not specified [ 0.573886] msm-dcc b3000.dcc: jiffies_64: 0xffff8b08, cntvct_64: 0xb054731 [ 0.573898] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003ce004) [ 0.573909] msm-dcc b3000.dcc: gcnt_lo: 0x0b0548f9(0xffffff80003ce000) [ 0.574548] TZ SMMU State: SMMU Stage2 Enabled [ 0.574626] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not s et [ 0.576227] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 0.576265] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.576300] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) i s a MSM [ 0.576318] msm_serial: console setup on port #0 [ 1.402862] console [ttyMSM0] enabled [ 1.407856] msm_serial 78b1000.serial: msm_serial: detected port #1 [ 1.411123] msm_serial 78b1000.serial: uartclk = 19200000 [ 1.417210] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM [ 1.423066] msm_serial: driver initialized [ 1.431563] msm_serial_hsl_init: driver initialized [ 1.443738] brd: module loaded [ 1.444973] flash_chrdev : flash_chrdev_init [ 1.445678] flash_chrdev : flash_chrdev_init [ 1.450939] QPIC controller hw version Major:1, Minor:5 [ 1.454810] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x61 [ 1.459486] nand: ONFI 10-Compliant GigaDevice PSR1GA30DT [ 1.466127] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.471456] 17 ofpart partitions found on MTD device qcom_nand.0 [ 1.478855] Creating 17 MTD partitions on "qcom_nand.0": [ 1.485018] 0x000000000000-0x000000100000 : "0:SBL1" [ 1.491858] 0x000000100000-0x000000200000 : "0:MIBIB" [ 1.496731] 0x000000200000-0x000000280000 : "0:BOOTCONFIG" [ 1.501269] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1" [ 1.506627] 0x000000300000-0x000000600000 : "0:QSEE" [ 1.514296] 0x000000600000-0x000000680000 : "0:DEVCFG" [ 1.517315] 0x000000680000-0x000000700000 : "0:APDP" [ 1.522237] 0x000000700000-0x000000780000 : "0:RPM" [ 1.527392] 0x000000780000-0x000000800000 : "0:CDT" [ 1.531950] 0x000000800000-0x000000980000 : "0:APPSBLENV" [ 1.537700] 0x000000980000-0x000000b80000 : "0:APPSBL" [ 1.543687] 0x000000b80000-0x000000c00000 : "0:ART" [ 1.547406] 0x000000c00000-0x000003600000 : "rootfs" [ 1.588415] mtd: device 12 (rootfs) set to be root filesystem [ 1.588737] mtdsplit: no squashfs found in "rootfs" [ 1.593137] 0x000003600000-0x000006000000 : "rootfs_1" [ 1.635136] 0x000006000000-0x000006080000 : "0:ETHPHYFW" [ 1.636185] 0x000006080000-0x000006980000 : "factory_data" [ 1.647896] 0x000006980000-0x000007a80000 : "runtime_data" [ 1.664180] libphy: Fixed MDIO Bus: probed [ 3.774917] gpio_set_value 44: 0 [1.5s~2s] gpio_set_value 44: 1 [ 6.044230] gpio_set_value 37: 0 [1.5s~2s] gpio_set_value 37: 1 [ 6.557237] qca-mdio 90000.mdio: Could not find phy-reset-gpio [ 6.557358] libphy: qca_mdio: probed [ 6.562715] qca-mdio 90000.mdio: qca-mdio driver was registered [ 6.565957] Unable to create IPC log context! [ 6.571594] Skip QCA8074V1 in V2 platform [ 6.576124] cnss: Platform driver probed successfully. plat ffffffc03d0e2018 tgt 0xfff e [ 6.580077] i2c /dev entries driver [ 6.596177] sdhci: Secure Digital Host Controller Interface driver [ 6.596204] sdhci: Copyright(c) Pierre Ossman [ 6.601245] sdhci-pltfm: SDHCI platform and OF driver helper [ 6.606292] sdhci_msm 7824900.sdhci: sdhci_msm_probe: ICE device is not enabled [ 6.611448] sdhci_msm 7824900.sdhci: No vreg data found for vdd [ 6.618457] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io [ 6.625659] sdhci_msm 7824900.sdhci: No vmmc regulator found [ 6.630586] sdhci_msm 7824900.sdhci: No vqmmc regulator found [ 6.674272] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 6.694424] [ 6.694424] Version Rollback Feature Disabled [ 6.699015] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000 008b04000 [ 6.703233] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000 008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04 000 [ 6.723341] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000 008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04 000 [ 6.735184] sps:BAM 0x0000000008b04000 is registered.[ 6.745177] remoteproc remotep roc0: releasing cd00000.qcom_q6v5_wcss [ 6.748467] SPMI VADC - Min ch: 0 Max ch: 15 [ 6.755698] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 [ 6.758174] coresight-csr 6001000.csr: CSR initialized [ 6.765662] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 [ 6.770582] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 [ 6.778148] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 [ 6.785507] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 [ 6.792869] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 [ 6.800268] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 [ 6.807640] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 [ 6.815045] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 [ 6.822382] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 [ 6.829781] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 [ 6.837156] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 [ 6.844536] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 [ 6.851896] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 [ 6.859292] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 [ 6.866671] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 [ 6.874032] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 [ 6.881427] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 [ 6.889021] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 [ 6.896336] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 [ 6.903747] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 [ 6.911186] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 [ 6.918525] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000 006044000 [ 6.925557] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000 006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044 000 [ 6.942659] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000 006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044 000 [ 6.958536] sps:BAM 0x0000000006044000 is registered.[ 6.966234] coresight-tmc 6028 000.tmc: TMC initialized [ 6.970994] coresight-tmc 6027000.tmc: TMC initialized [ 6.976142] coresight-funnel 6021000.funnel: FUNNEL initialized [ 6.981148] coresight-funnel 6100000.funnel: FUNNEL initialized [ 6.986984] coresight-funnel 6120000.funnel: FUNNEL initialized [ 6.992864] coresight-funnel 6130000.funnel: FUNNEL initialized [ 6.998796] coresight-funnel 61a1000.funnel: FUNNEL initialized [ 7.005280] coresight-etm4x 619c000.etm: ETM 4.0 initialized [ 7.010939] coresight-etm4x 619d000.etm: ETM 4.0 initialized [ 7.016905] coresight-etm4x 619e000.etm: ETM 4.0 initialized [ 7.022586] coresight-etm4x 619f000.etm: ETM 4.0 initialized [ 7.027818] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized [ 7.033537] coresight-stm 6002000.stm: STM initialized [ 7.042151] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 [ 7.046000] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized [ 7.054298] fan-gpio soc:fans: gpio_fan_probe success [ 7.061382] antenna-gpio soc:antennas: gpio_fan_probe success [ 7.066391] modem-gpio soc:modem: gpio_fan_probe success [ 7.074396] nf_conntrack version 0.5.0 (6924 buckets, 27696 max) [ 7.077681] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.083596] NET: Registered protocol family 10 [ 7.089238] NET: Registered protocol family 17 [ 7.092757] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Upda te your scripts to load br_netfilter if you need this. [ 7.097202] Bridge firewalling registered [ 7.109923] 8021q: 802.1Q VLAN Support v1.8 [ 7.115365] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 7.117957] pmd9655_s3: supplied by e-smps1-reg [ 7.125296] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 7.129616] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1 [ 7.136248] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 7.143879] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 7.151422] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 7.160535] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS : open-loop= 704000 uV [ 7.167480] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM : open-loop= 808000 uV [ 7.177462] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO : open-loop= 864000 uV [ 7.187272] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO : open-loop= 944000 uV [ 7.197146] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 767, quot_offset[ 7]= 0 [ 7.206895] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 972, quot_offset[ 7]= 205 [ 7.217744] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1073, quot_offset[ 7]= 100 [ 7.228682] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1226, quot_offset[ 7]= 150 [ 7.239742] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 7.251063] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2 [ 7.257413] pmd9655_s4: supplied by e-smps1-reg [ 7.264558] cpr3_mem_acc_init: npu: not using memory accelerator regulator [ 7.268854] npu_corner: fused NOM: open-loop= 776000 uV [ 7.275808] npu_corner: fused TURBO: open-loop= 832000 uV [ 7.281649] npu_corner: fused NOM: open-loop= 776000 uV [ 7.287264] npu_corner: fused TURBO: open-loop= 832000 uV [ 7.292918] npu_corner: Normal and Cold condition init done. Default to normal. [ 7.299694] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz [ 7.305757] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017 600 KHz [ 7.314416] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_ q6v5_wcss [ 7.321581] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available [ 7.330269] ubi0: attaching mtd12 [ 7.544562] ubi0: scanning is finished [ 7.550779] ubi0: attached mtd12 (name "rootfs", size 42 MiB) [ 7.550797] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.555498] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.562262] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.569125] ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 [ 7.575893] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 7.582142] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence numb er: 273099923 [ 7.589180] ubi0: available PEBs: 108, total reserved PEBs: 228, PEBs reserved for bad PEB handling: 20 [ 7.598127] ubi0: background thread "ubi_bgt0d" started, PID 109 [ 7.619118] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0 [ 7.619187] hctosys: unable to open rtc device (rtc0) [ 7.630753] pmd9655_ldo11: disabling [ 7.631286] ALSA device list: [ 7.634571] No soundcards found. [ 7.639610] VFS: Mounted root (squashfs filesystem) readonly on device 31:18. [ 7.640778] Freeing unused kernel memory: 220K (ffffffc0007e2000 - ffffffc000819000) [ 7.647919] Freeing alternatives memory: 40K (ffffffc000819000 - ffffffc000823000) [ 7.909292] init: Console is alive [ 7.909373] init: - watchdog - [ 7.928794] random: nonblocking pool is initialized [ 8.683951] usbcore: registered new interface driver usbfs [ 8.683992] usbcore: registered new interface driver hub [ 8.688411] usbcore: registered new device driver usb [ 8.694189] Button Hotplug driver version 0.4.1 [ 8.702098] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 8.764429] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 8.826336] msm-usb-ssphy-qmp 78000.ssphy: Initializing QMP phy [ 8.833021] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout [ 8.833042] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868 [ 9.039872] msm-usb-ssphy-qmp 58000.ssphy: Initializing QMP phy [ 9.047170] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout [ 9.047191] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868 [ 9.253329] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.304420] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.364415] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.425595] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.484410] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.544602] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.604389] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.664780] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 9.664809] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 9.669281] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0 x00010010 [ 9.676758] xhci-hcd xhci-hcd.0.auto: irq 208, io mem 0x08a00000 [ 9.685663] hub 1-0:1.0: USB hub found [ 9.691635] hub 1-0:1.0: 1 port detected [ 9.695335] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 9.699269] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 9.704609] usb usb2: We don't know the algorithms for LPM for this host, disabling LP M. [ 9.712304] hub 2-0:1.0: USB hub found [ 9.720456] hub 2-0:1.0: 1 port detected [ 9.724148] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 9.728096] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 9.733497] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0 x00010010 [ 9.740959] xhci-hcd xhci-hcd.1.auto: irq 209, io mem 0x08c00000 [ 9.749817] hub 3-0:1.0: USB hub found [ 9.755873] hub 3-0:1.0: 1 port detected [ 9.759528] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 9.763504] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 9.768826] usb usb4: We don't know the algorithms for LPM for this host, disabling LP M. [ 9.776543] hub 4-0:1.0: USB hub found [ 9.784692] hub 4-0:1.0: 1 port detected [ 9.788686] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.845559] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.904405] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 9.964452] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 10.014218] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 10.912071] init: - preinit - ignore preinit load_wifi_board_bin Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root mounting /dev/root cp: can't stat '/tmp/log_export_tmp/*': No such file or directory After mount_root [ 14.254950] procd: - early - [ 14.254987] procd: - watchdog - [ 14.878749] procd: - ubus - [ 15.880871] procd: - init - Please press Enter to activate this console. [ 15.926739] ubi1: attaching mtd15 [ 15.972067] ubi1: scanning is finished [ 15.978201] ubi1: attached mtd15 (name "factory_data", size 9 MiB) [ 15.978220] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 15.983261] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 15.990131] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 15.996981] ubi1: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 [ 16.003744] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 16.009657] ubi1: max/mean erase counter: 11/6, WL threshold: 4096, image sequence num ber: 1097309032 [ 16.016950] ubi1: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PE B handling: 20 [ 16.026245] ubi1: background thread "ubi_bgt1d" started, PID 214 ubi_factory_data found, mounting... [ 16.055184] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 221 [ 16.090330] UBIFS (ubi1:0): recovery needed [ 16.170166] UBIFS (ubi1:0): recovery completed [ 16.170216] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_factory_d ata" [ 16.173495] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes : 2048 bytes/2048 bytes [ 16.181753] UBIFS (ubi1:0): FS size: 4825088 bytes (4 MiB, 38 LEBs), journal size 1142 785 bytes (1 MiB, 9 LEBs) [ 16.191732] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB) [ 16.201621] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID 555FE482-AC27- 41A3-A0C3-47CC50ED88FA, small LPT model [ 16.213139] ubi2: attaching mtd16 [ 16.304218] ubi2: scanning is finished [ 16.310419] ubi2: attached mtd16 (name "runtime_data", size 17 MiB) [ 16.310439] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 16.315490] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 16.322424] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 16.329287] ubi2: good PEBs: 136, bad PEBs: 0, corrupted PEBs: 0 [ 16.336055] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 16.342304] ubi2: max/mean erase counter: 15/8, WL threshold: 4096, image sequence num ber: 728371170 [ 16.349342] ubi2: available PEBs: 0, total reserved PEBs: 136, PEBs reserved for bad P EB handling: 20 [ 16.358637] ubi2: background thread "ubi_bgt2d" started, PID 227 ubi_runtime_data found, mounting... [ 16.374436] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 234 [ 16.407601] UBIFS (ubi2:0): recovery needed [ 16.496562] UBIFS (ubi2:0): recovery completed [ 16.496628] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "ubi_runtime_d ata" [ 16.499899] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes : 2048 bytes/2048 bytes [ 16.508153] UBIFS (ubi2:0): FS size: 9904128 bytes (9 MiB, 78 LEBs), journal size 1777 664 bytes (1 MiB, 14 LEBs) [ 16.518134] UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB) [ 16.528364] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID EB7DF1AC-F4C9- 4CA1-A141-55D4B7DCC73E, small LPT model WIFI FW mount is successful [ 17.073271] use sfe_cm.ko and sfe_drv_init do nothing [ 17.081485] cfg80211: World regulatory domain updated: [ 17.081509] cfg80211: DFS Master region: unset [ 17.085535] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_ei rp), (dfs_cac_time) [ 17.090119] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A ) [ 17.099823] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 17.107494] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A ) [ 17.116861] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A , 2000 mBm), (N/A) [ 17.124856] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A , 2000 mBm), (0 s) [ 17.134573] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 17.144027] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A ) [ 17.152105] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/ A) [ 17.298616] ssdk_switch_device_num_init[1084]:INFO:ess-switch dts node number: 1 [ 17.302311] ssdk_dt_get_switch_node[919]:INFO:ess-switch DT exist! [ 17.309316] ssdk_dt_parse_access_mode[820]:INFO:switch_access_mode: local bus [ 17.315481] ssdk_dt_parse_access_mode[833]:INFO:switchreg_base_addr: 0x3a000000 [ 17.322595] ssdk_dt_parse_access_mode[834]:INFO:switchreg_size: 0x1000000 [ 17.329885] ssdk_dt_parse_mac_mode[288]:INFO:mac mode = 0x0 [ 17.336310] ssdk_dt_parse_mac_mode[297]:INFO:mac mode1 = 0xf [ 17.341863] ssdk_dt_parse_mac_mode[306]:INFO:mac mode2 = 0xf [ 17.347519] ssdk_dt_parse_phy_info[639]:INFO:[PORT 5] port_mac_sel = QGMAC_PORT [ 17.353163] ssdk_dt_parse_uniphy[325]:INFO:ess-uniphy DT exist! [ 17.360626] ssdk_plat_init start [ 17.435858] ssdk_gcc_clock_init[629]:INFO:SSDK gcc clock init successfully! [ 17.438980] ssdk_probe[1923]:INFO:ess_rst doesn't exist! [ 17.446092] HPPE initializing... [ 17.446964] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0xffff ffff phytype doesn't match [ 17.454346] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 1, phy_id = 0xffff ffff phytype doesn't match [ 17.464487] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 2, phy_id = 0xffff ffff phytype doesn't match [ 17.474639] ssdk_phy_driver_init[299]:INFO:dev_id = 0, phy_adress = 3, phy_id = 0xffff ffff phytype doesn't match [ 17.484817] qca803x_phy_api_ops_init[2180]:INFO:qca probe qca803x phy driver succeeded ! [ 17.495373] qca808x_phy_api_ops_init[2155]:INFO:qca probe qca808x phy driver succeeded ! [ 17.504170] qca808x_ptp_register[1410]:INFO:qca808x ptp clock registered [ 17.510927] regi_init[3374]:INFO:Initializing HPPE!! [ 17.734205] ssdk_ppe_reset_init[860]:INFO:ppe reset successfully! [ 17.740152] qca_hppe_tdm_hw_init[674]:INFO:tdm setup num=96 [ 17.743526] qca_hppe_portctrl_hw_init[105]:INFO:Hawkeye PPE port initializing [ 20.121261] ssdk_switch_register[1632]:INFO:Chip version 0x1500 [ 20.124241] qca_link_polling_select[1282]:INFO:link-polling-required node does not exi st [ 20.130479] ssdk_switch_register[1657]:INFO:polling is selected [ 20.138207] regi_init[3378]:INFO:Initializing HPPE Done!! [ 20.143109] regi_init[3439]:INFO:qca-ssdk module init succeeded! [ 20.149572] tun: Universal TUN/TAP device driver, 1.6 [ 20.151576] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 20.158534] EDMA ver 1 hw init [ 20.162820] EDMA HW Reset completed succesfully [ 20.165716] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 20.170065] RxDesc:1 (15-15) RxFill:1 (7-7) [ 20.175793] GMAC1(ffffffc039c95880) Invalid MAC@ - using 4e:c7:5c:67:64:44 [ 20.179513] libphy: PHY 90000.mdio:00 not found [ 20.186434] nss-dp: probe of 3a001000.dp1 failed with error -14 [ 20.190842] GMAC2(ffffffc039c95880) Invalid MAC@ - using 92:78:26:ac:59:bc [ 20.196754] libphy: PHY 90000.mdio:01 not found [ 20.203663] nss-dp: probe of 3a001200.dp2 failed with error -14 [ 20.208121] GMAC3(ffffffc039c95880) Invalid MAC@ - using c2:7a:99:cf:86:6d [ 20.214014] libphy: PHY 90000.mdio:02 not found [ 20.220946] nss-dp: probe of 3a001400.dp3 failed with error -14 [ 20.225394] GMAC4(ffffffc039c95880) Invalid MAC@ - using 52:cf:f0:55:6b:32 [ 20.231289] libphy: PHY 90000.mdio:03 not found [ 20.238221] nss-dp: probe of 3a001600.dp4 failed with error -14 [ 20.242660] GMAC5(ffffffc039c95880) Invalid MAC@ - using 4a:0a:3c:22:81:37 [ 20.450376] GMAC6(ffffffc039c9a880) Invalid MAC@ - using f6:97:bf:07:c2:59 [ 20.524889] ********************************************************** [ 20.524913] * NSS Data Plane driver [ 20.530293] ********************************************************** [ 20.535616] l2tp_core: L2TP core driver, V2.0 [ 20.540791] l2tp_netlink: L2TP netlink interface [ 20.665667] nss_driver - fw of size 743024 bytes copied to load addr: 40000000, nss_i d : 0 [ 20.667337] Supported Frequencies - [ 20.672813] 748.8 MHz 1.4976 GHz [ 20.678794] 1.6896 GHz [ 20.679839] [ 20.682202] ffffffbffc597100: set sdma ffffffc03ba31e00 [ 20.683726] ffffffbffc597100: meminfo init succeed [ 20.717638] node size 2 # items 4 [ 20.717660] memory: 40000000 1073741824 (avl 938553344) items 4 active_cores 2 [ 20.719997] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 20.727094] ffffffbffc597100: nss core 0 booted successfully [ 20.734777] nss_driver - fw of size 289420 bytes copied to load addr: 40800000, nss_i d : 1 [ 20.740574] Supported Frequencies - [ 20.747803] 748.8 MHz 1.4976 GHz [ 20.753767] 1.6896 GHz [ 20.754813] [ 20.757183] ffffffbffc59e680: set sdma ffffffc03a528a00 [ 20.758705] ffffffbffc59e680: meminfo init succeed [ 20.765065] sit: IPv6 over IPv4 tunneling driver [ 20.767053] node size 2 # items 4 [ 20.767056] memory: 40000000 1073741824 (avl 938553344) items 4 active_cores 2 [ 20.767087] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 20.767095] ffffffbffc59e680: nss core 1 booted successfully [ 20.791635] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded. [ 20.800437] tipc: Activated (version 2.0.0) [ 20.804000] NET: Registered protocol family 30 [ 20.808036] tipc: Started in single node mode [ 20.812841] gre: GRE over IPv4 demultiplexor driver [ 20.817518] ip_gre: GRE over IPv4 tunneling driver [ 20.822824] ip6_gre: GRE over IPv6 tunneling driver [ 20.828320] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 20.843347] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.848091] openvswitch: Open vSwitch switching datapath [ 20.851584] QCA Hy-Fi multicast installation successfully [ 20.856953] PPP generic driver version 2.4.2 [ 20.859917] nss_lag_init[354]:LAG Manager Installed [ 20.864162] NET: Registered protocol family 24 [ 20.869150] PPTP driver version 0.8.5 [ 20.877102] diag: IPC Logging disabled [ 20.887503] TRACK: P[0] PMask[4] [ 20.887523] TRACK: P[1] PMask[4] [ 20.889787] TRACK: P[2] PMask[4] [ 20.895158] TRACK: P[3] PMask[4] [ 20.896257] nik 4097 info->svc_id [ 20.902610] QCA multicast snooping installed successfully [ 20.903510] <NSS-CRYPTO>:module loaded Build_ID - 04/10/23, 21:12:08 SoC=ipq807x_64 [ 20.911923] cannot find nss-macsec0 node [ 20.915626] cannot find nss-macsec1 node [ 20.919673] cannot find nss-macsec2 node [ 20.923553] nss_macsec init success [ 20.929554] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 20.994971] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.067009] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.154844] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.227321] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.294910] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.355276] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.414834] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.475341] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.544804] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.605119] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.664771] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.725247] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.785175] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.844737] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.905193] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 21.974781] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.035225] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.094757] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.155212] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.214776] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.274702] u32 classifier [ 22.274717] Performance counters on [ 22.276293] input device check on [ 22.280042] Actions configured [ 22.284472] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.344760] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.404792] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.465155] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.524689] Mirror/redirect action on [ 22.525251] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.584782] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.645186] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.704794] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.765253] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.824764] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.884836] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 22.945246] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.004822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.065298] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.124822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.185261] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.244812] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.305259] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.364810] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.425233] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.494840] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.555219] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.615253] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.674816] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.734822] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.795259] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.855261] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.914830] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 23.975257] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.034835] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.094835] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.155432] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.214884] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.275272] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.334865] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.395258] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.454861] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.515298] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.574858] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.635343] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.694854] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.755248] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.814879] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.876211] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.925030] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 24.995221] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.064959] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.125926] mhi_init Quectel_Linux_PCIE_MHI_Driver_V1.3.0.13 [ 25.126051] rmnet_nss_init(): initializing rmnet_nss [ 25.130840] mhi_pci_probe pci_dev->name = 0000:01:00.0, domain=0, bus=1, slot=0, vendo r=17CB, device=0306 [ 25.135803] mhi_q 0000:01:00.0: BAR 0: assigned [mem 0x20300000-0x20300fff 64bit] [ 25.145154] mhi_q 0000:01:00.0: enabling device (0000 -> 0002) [ 25.153910] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.215521] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.274869] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.334768] device recognition register succes [ 25.335412] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.366165] [I][mhi_netdev_enable_iface] Prepare the channels for transfer [ 25.396637] [I][mhi_netdev_enable_iface] Exited. [ 25.397025] rmnet_vnd_register_device(rmnet_mhi0.1)=0 [ 25.400987] net rmnet_mhi0 rmnet_mhi0.1: NSS context created [ 25.405370] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.485089] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.545388] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.604915] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.665411] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.725312] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 25.786144] Ebtables v2.0 registered [ 25.787644] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 25.938326] Netfilter messages via NETLINK v0.30. [ 25.941881] usbcore: registered new interface driver usbserial [ 25.942038] usbcore: registered new interface driver usbserial_generic [ 25.947856] usbserial: USB Serial support registered for generic [ 25.961207] xt_time: kernel timezone is -0000 [ 25.962070] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 26.047647] ctnetlink v0.93: registering with nfnetlink. [ 26.052339] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) [ 26.105538] usbcore: registered new interface driver option [ 26.105586] usbserial: USB Serial support registered for GSM modem (1-port) [ 26.110033] option 1-1:1.0: GSM modem (1-port) converter detected [ 26.117006] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 [ 26.123181] option 1-1:1.1: GSM modem (1-port) converter detected [ 26.130064] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 [ 26.136096] option 1-1:1.2: GSM modem (1-port) converter detected [ 26.142861] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 [ 26.148947] option 1-1:1.3: GSM modem (1-port) converter detected [ 26.155738] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3 [ 26.162833] dwc3_qcom: exports duplicate symbol msm_data_fifo_config (owned by dwc3_of _simple) reloadprofile() begin reloadprofile() end ==reloadConfig()== begin ==loadDefaultConfig()== begin ==loadConfigToFiles(): default-config to /tmp/defaultconfig== begin ==loadConfigToFiles()== end ==set_usrconfig_info()== start ==set_usrconfig_info()== end ==loadDefaultConfig()== end ==loadConfigToFiles(): user-config to /tmp/userconfig== begin ==loadConfigToFiles()== end ==reloadConfig()===== no need to load emmc-config ==loadConfigToFiles(): device-config to /tmp/userconfig== begin ==loadConfigToFiles()== end ** user-config loaded ** ==reloadConfig()== end merge_extra_config() begin ==loadConfigToFiles(): default-config to /tmp/merge== begin ==loadConfigToFiles()== end mergeconfigbycountry() begin mergeconfigbycountry() country US mergeconfigbycountry() end merge_extra_config() end phylink down boot 1 [ 27.491774] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 27.502940] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 27.715276] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready acfg_tool: Issuing blocking call to wait for events [ 28.479951] ECM init [ 28.480004] ECM database jhash random seed: 0x2fe6736c [ 28.482051] ECM init complete [ 28.494704] ECM OVS Test INIT switch: reset_wan_vlan: select p4: 1 switch: reset_wan_vlan: select p5: 2 [ 30.076407] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready [ 30.122680] Load statistics in Router Mode [ 30.122763] module inited to down eth0/1 after netfid [ 30.296120] ext_antenna_en_store ==>gpio 56 value 0 buf 0 [ 30.296120] [awnd_update_wifi_tpie:911]: config_generic failed awnd_update_tpie(): ath02[-1] [awnd_update_wifi_tpie:911]: config_generic failed awnd_update_tpie(): ath12[-1] apsd: start apsd whc (repacd): Start: whc (repacd): GatewayConnectedMode(gwcon_mode): CAP whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1 whc (repacd): get whc_wifi_config_lock whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: lan whc (repacd): Device type: AP whc (repacd): Sysmode: Router whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert _state wifi guest enable) whc (repacd): stop repacd-run.sh whc (repacd): Start: whc (repacd): GatewayConnectedMode(gwcon_mode): CAP whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1 whc (repacd): wifi config change(is different from /var/state/wifi). wifi_cmd:reload wifi 1,wifi0 whc (repacd): Using SON mode for GW Connected AP whc (repacd): __repacd_restart_dependencies: Restarting network stack... wifi reload [ 32.429779] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready [ 32.431707] [I][mhi_netdev_open] Opened net dev interface [ 32.435036] IPv6: ADDRCONF(NETDEV_UP): rmnet_mhi0: link is not ready [ 32.441973] 8021q: VLANs not supported on rmnet_mhi0 [ 32.446890] IPv6: ADDRCONF(NETDEV_UP): rmnet_mhi0.1: link is not ready [ 32.455784] device eth0 entered promiscuous mode [ 32.458065] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 32.465207] device eth1 entered promiscuous mode [ vlan_set_device_state ] 165: --------------->Create VID='1' qcawifi qcawificfg80211 disable radio wifi1 qcawifi qcawificfg80211 disable radio wifi0 qcawifi qcawificfg80211 disable radio wifi2 qcawifi qcawificfg80211: enable radio wifi1 echo -n /ini > /sys/module/firmware_class/parameters/path update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 sysctl -w dev.nss.n2hcfg.extra_pbuf_core0=9000000 [ 33.534121] configuring additional NSS pbufs [ 33.560538] additional pbufs of size 9003008 got added to NSS sysctl -w dev.nss.n2hcfg.n2h_high_water_core0=67392 sysctl -w dev.nss.n2hcfg.n2h_wifi_pool_buf=40960 insmod mem_manager [ 33.584124] mem_manager: module license 'Proprietary' taints kernel. [ 33.584152] Disabling lock debugging due to kernel taint insmod qdf mem_debug_disabled=1 insmod asf insmod umac enable_pktlog_support=1 [ 33.952252] wlan: [2582:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50 insmod qca_spectral echo 1 > /sys/module/cnss2/parameters/cold_boot_support echo 1 > /sys/module/cnss2/parameters/daemon_support *****starting cnssdaemon***** *********initiating cold boot calibration************* insmod qca_ol testmode=7 echo -1000 > /proc/`pgrep cnssdaemon`/oom_score_adj *****cnssdaemon pid=2617********* insmod wifi_3_0 [ 34.210926] wlan: [2623:I:ANY] =======ol_if_register_wifi3_0========== [ 34.210926] [ 34.210962] wlan: [2623:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered f or target_type:1 with soc_ops:ffffffbffd649a40 [ 34.217870] wlan: [2623:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_ type 1 [ 34.229930] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss [ 34.248883] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 35.215357] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up [ 35.215421] wlan: [2623:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_ type 1 [ 35.215824] rpmsg_dev_probe: No pm domain [ 35.215975] rpmsg_dev_probe: No pm domain [ 35.216853] cnss: QMI WLFW service connected, state: 0x1 [ 35.216998] cnss: device_id : 65534 mem mode : [0] [ 35.217086] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc9dacc8 [ 35.218749] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, s oc_id: 0xffffffff, fw_version: 0x220604a5, fw_build_timestamp: 2021-08-12 01:51, otp_vers ion: 0x0 eeprom_caldata_read_timeout 0s [ 35.218757] cnss: Downloading BDF: bdwlan.bin, size: 64 [ 35.218762] cnss: No board_id entry in device tree [ 35.219162] cnss: BDF location : 0x4b0c0000 [ 35.219167] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 35.219382] cnss: Downloading BDF: caldata.bin, size: 64 [ 35.219801] cnss: per device BDF location : 0x4b0e0000 [ 35.219886] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 35.306486] wlan: [2623:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe [ 35.313326] wlan: [2623:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for devic e fffe [ 35.322423] wlan: [2623:I:ANY] pld_ahb_wlan_enable: 691: cnss_mode: Cold boot calibrat ion [ 35.406828] wlan: [2623:I:ANY] Coldboot calibration wait started [ 35.406828] not found in config echo 0 to init ===parental_control_avira=== no need to start [ 36.186999] mode:0 [ 3366(lan)] [smartip_get_cfg 166] key:gw value:192.168.68.1 [ 3366(lan)] [smartip_get_cfg 166] key:lanip value:192.168.68.1 [ 3366(lan)] [smartip_get_cfg 166] key:lantype value:1 GMT-12:00 [ 3366(lan)] [smartip_get_cfg 166] key:mask value:255.255.252.0 false 0 [ 3366(lan)] [smartip_init_dhcp_hook_socket 2329] create dhcp ho[ 36.757355] g_back_dev _num:16 ok success [ 3366(lan)] [smartip_start_drop_dhcp_pkg 2215] start select dhcp package! [ 3366(lan)] [smartip_check_status_Router_mode 1719] new dnsServer is 0xc0a84401 0x0 [ 3366(lan)] [smartip_notify_lan_update 1320] Notify the lan ip changed. [ 3366(lan)] [smartip_update_lanip 593] config IP: ifconfig br-lan 192.168.68.1 netmask 255.255.252.0 [ 3366(lan)] [smartip_update_lanip 604] route del default dev br-lan [ 3366(lan)] [smartip_update_lanip 622] restart miniupnpd [ 3623(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:UPDATE [ 3669(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:FAPIPUPDATE IPConflict2 mask:22 lan_addr:192.168.68.1 mask_str:255.255.252.0 IPConflict2 mask:22 IPConflict2 old_mask:255.255.252.0 old_ip:192.168.68.1 [ 37.027652] mode:0 [ 3366(lan)] [smartip_update_lanip 634] restart domain_login [ 3366(lan)] [smartip_start_process 366] start udhcpd [ 38.566713] Ebtables v2.0 unregistered [ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! [ 41.107046] wlan: [2623:I:ANY] Coldboot calibration wait ended [ 41.107046] [ 41.108717] wlan: [2623:I:ANY] ol_ath_do_cold_boot_calibration: 598: Coldboot calib su ccessful: radio_id 0x65534 [ 41.108777] cnss: QMI WLFW service disconnected, state: 0x6 [ 41.124118] wlan: [2623:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/ multi-bss) [ 41.134504] wlan: [3807:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 0 bus_ type 1 rmmod wifi_3_0 [ 41.163768] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss [ 41.163817] wlan: [3807:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 1 bus_ type 1 rmmod qca_ol insmod qca_ol insmod wifi_3_0 [ 41.299397] wlan: [3815:I:ANY] =======ol_if_register_wifi3_0========== [ 41.299397] [ 41.299433] wlan: [3815:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered f or target_type:1 with soc_ops:ffffffbffd897a40 [ 41.306266] wlan: [3815:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 2 bus_ type 1 [ 41.318385] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss [ 41.327102] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 41.684235] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up [ 41.684303] wlan: [3815:I:ANY] ol_ath_wifi_ssr: 256: ol_ath_wifi_ssr: SSR event 3 bus_ type 1 [ 41.684685] rpmsg_dev_probe: No pm domain [ 41.684857] rpmsg_dev_probe: No pm domain [ 41.685472] cnss: QMI WLFW service connected, state: 0x1 [ 41.685628] cnss: device_id : 65534 mem mode : [0] [ 41.695764] cnss: Target capability: chip_id: 0x0, chip_family: 0x0, board_id: 0xff, s oc_id: 0xffffffff, fw_version: 0x220604a5, fw_build_timestamp: 2021-08-12 01:51, otp_vers ion: 0x0 eeprom_caldata_read_timeout 0s [ 41.695772] cnss: Downloading BDF: bdwlan.bin, size: 64 [ 41.695777] cnss: No board_id entry in device tree [ 41.696164] cnss: BDF location : 0x4b0c0000 [ 41.696165] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 41.696392] cnss: Downloading BDF: caldata.bin, size: 64 [ 41.696749] cnss: per device BDF location : 0x4b0e0000 [ 41.696846] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 41.765976] wlan: [3815:I:ANY] ol_ath_check_fw_ready: 614: Waiting for FW ready device fffe [ 41.772814] wlan: [3815:I:ANY] ol_ath_check_fw_ready: 624: FW ready received for devic e fffe [ 41.781514] wlan: [3815:I:ANY] pld_ahb_wlan_enable: 699: cnss_mode: Mission mode [ 41.798345] wlan: [3815:I:ANY] qca_napi_create: 364: qca_napi_create: napi instance 0 created on pipe 4 [ 41.798532] wlan: [3815:I:ANY] __ol_ath_attach: 3922: Allocated soc ffffffc031180880 [ 41.824310] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_t x=1000 - Out of range [8, 100]; Using 1000 [ 41.824438] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_buf_rin g=8192 - Out of range [16, 4096]; Using 2048 [ 41.834959] wlan: [3815:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_dst_rin g=8192 - Out of range [48, 4096]; Using 1024 [ 41.846666] wlan: [3815:I:ANY] osif_nss_wifi_soc_setup: 170: nss-wifili: Could not set nss_cfg due to Invalid HW mode 7 [ 41.858212] wlan: [3815:I:ANY] osif_nss_wifi_soc_setup: 204: nss register id -1 nss co nfig 3 Target Type 18 [ 41.868902] wlan: [3815:I:ANY] __ol_ath_attach: 4129: dev name soc0 [ 41.879110] wlan: [3815:I:ANY] ol_ath_soc_attach: 7124: WMI attached. wmi_handle fffff fc034e57400 [ 41.885027] wlan: [3815:I:ANY] htc_wmi_init: 6134: htc_wmi_init() HT Create . ffffffc0 338dc000 [ 41.893964] wlan: [3815:I:ANY] htc_wmi_init: 6141: htc_wmi_init() Skipping BMI Done. [ 41.902564] wlan: [3815:I:ANY] htc_wmi_init: 6198: [htc_wmi_init:6198] host_enable 0 n ss_nwifi_offload 0 [ 41.913048] wlan: [3815:I:ANY] ol_target_init_complete: 6320: CDP soc attach success [ 41.920020] wlan: [3815:I:ANY] ol_target_init_complete: 6327: Soc attach success NSS c onfig 0 [ 41.927781] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle fff fffc0338dc000, ep 2, value 1 [ 41.936197] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle fff fffc0338dc000, ep 3, value 1 [ 41.946526] wlan: [3815:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle fff fffc0338dc000, ep 4, value 1 [ 41.957172] wlan: [485:I:TIF] init_deinit_populate_hw_mode_capability: 361: Preferred mode is not set, use mode id 1 [ 41.957172] [ 41.967159] wlan: [485:I:TIF] HE_CAP Info = 1a08010d [ 41.979207] wlan: [485:I:TIF] Num HW modes = 1 [ 41.984237] wlan: [485:I:TIF] Num PHY = 2 [ 41.988490] wlan: [485:I:TIF] Preferred HW Mode = 1 Num Radios = 2 [ 41.992574] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes, [ 41.998656] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 0 wireless m odes = f97f9001 [ 42.007251] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1779: Adding 11ax regulatory modes, [ 42.016451] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1783: phy_id = 1 wireless m odes = 680680c [ 42.024960] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001 [ 42.034159] wlan: [485:I:TIF] init_deinit_add_11ax_modes: 1806: hw_mode_id = 1 phy_id = 1 wireless modes = 680688c [ 42.044582] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notific ation: 421: dfs_offload 1 [ 42.054740] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2850: df s->dfs_psoc_idx: 0 [ 42.064718] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 2856: df s_soc_obj->num_dfs_privs: 1 [ 42.074643] wlan: [485:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notific ation: 393: Do not allocate DFS object for 2G, pdev_id = 1 [ 42.084728] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:0 wmi_ha ndle:ffffffc034e57400 [ 42.126670] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 0 Number of peers = 529 vdevs = 17 [ 42.126707] wlan: [485:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success [ 42.135855] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1347: pdev id:1 wmi_ha ndle:ffffffc034d11c00 [ 42.152559] wlan: [485:I:ANY] init_deinit_update_pdev_tgt_info: 1403: Pdev = 1 Number of peers = 529 vdevs = 17 [ 42.153795] wlan: [485:I:TIF] init_deinit_update_pdev_tgt_info: 1406: CDP PDEV ATTACH success [ 42.264304] wlan: [485:I:ANY] copy_fw_abi_version_tlv: 6960: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0 [ 42.463769] wlan: [485:I:ANY] ready_extract_init_status_tlv: 9002: ready_extract_init_ status_tlv:0 [ 42.463799] wlan: [485:I:ANY] dp_peer_map_attach_wifi3: 9790: dp_peer_map_attach_wifi3 max_peers 1109, max_ast_index: 4112 [ 42.463799] [ 42.471815] wlan: [3815:I:ANY] ol_ath_connect_htc: 1215: WMI is ready [ 42.484179] wlan: [3815:I:ANY] ol_ath_soc_attach: 7215: connect HTC [ 42.490628] wlan: [3815:I:ANY] ol_ath_soc_attach: 7216: bypasswmi : 0 [ 42.496716] wlan: [3815:I:ANY] ol_ath_soc_attach: 7290: ol_ath_soc_attach() UMAC attac h . [ 42.503355] wlan: [3815:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi0 [ 42.511468] wlan: [3815:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target [ 42.518666] wlan: [3815:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default [ 42.526092] wlan: [3815:I:ANY] ol_ath_pdev_attach: 9058: interface_id 0 [ 42.533595] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 0 Modes suppor ted [ 42.540022] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1 [ 42.548359] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 0 su pp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4900, hi_5g = 6100 [ 42.558611] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = f9 7f9001 before update [ 42.572921] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = f9 7f9001 after update [ 42.582660] wlan: [3815:I:ANY] ol_ath_update_ext_caps: 1932: 11ax 5G supported case [ 42.592374] wlan: [3815:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 42.599863] wlan: [3815:I:ANY] acfg_attach: 3519: acfg_attach: 3519: Netlink socket cr eated:ffffffc02b620400 [ 42.606350] wlan: [3815:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1 [ 42.616734] wlan: [3815:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4 [ 42.623799] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[1], ptr:ffffffbffd 3721e8 [ 42.630821] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d12008) Enabling DB DC Repeater 1 [ 42.639503] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc034d12008) is_primary 1 [ 42.648838] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14623: twt enabl ed. [ 42.648838] [ 42.650024] wlan: [3815:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block ch annel list is empty [ 42.650029] wlan: [3815:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 0 tx_desc_limit = 0 [ 42.650043] wlan: [3815:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 42.650043] [ 42.650045] wlan: [3815:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 42.650045] [ 42.650049] wlan: [3815:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffff c02b620800 ic->ic_wrap_com=ffffffc02b620800 &wrap_com->wc_devt=ffffffc02b620800 [ 42.650049] [ 42.650069] wlan: [3815:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60 [ 42.650245] wlan: [3815:I:ANY] ieee80211_cfg80211_radio_attach: 11806: ic: 0xffffffc03 0f60880, wdev: 0xffffffc030f78a58, wiphy: 0xffffffc0320442a0, netdev: 0xffffffc030f60000 [ 42.650707] wlan: [3815:I:ANY] __ol_ath_attach: 4242: pdev_netdev name wifi1 [ 42.650722] wlan: [3815:I:ANY] __ol_ath_attach: 4289: Skip txrx_pdev_attach_target [ 42.650725] wlan: [3815:I:ANY] __ol_ath_attach: 4315: BURSTING enabled by default [ 42.650763] wlan: [3815:I:ANY] ol_ath_pdev_attach: 9058: interface_id 1 [ 42.650774] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7444: phy id = 1 Modes suppor ted [ 42.650778] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7451: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1 [ 42.650782] wlan: [3815:I:TIF] ol_ath_pdev_regdmn_init: 7460: Reg cap - phy_id = 1 su pp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0 [ 42.650785] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1344: wireless_modes = 68 0680c before update [ 42.650787] wlan: [3815:I:ANY] ol_ath_update_wireless_modes: 1359: Wireless_modes = 68 0680c after update [ 42.650791] wlan: [3815:I:ANY] ol_ath_update_ext_caps: 1940: 11ax 2G supported case [ 42.650882] wlan: [3815:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 42.650988] wlan: [3815:I:ANY] acfg_attach: 3494: Offload using existing sock ffffffc0 2b620400 [ 42.650997] wlan: [3815:I:ANY] ol_ath_stats_attach: 2275: periodic_chan_stats: 1 [ 42.651164] wlan: [3815:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11 [ 42.651188] wlan: [0:I:ANY] ol_ath_pdev_attach: 9402: Set global_ic[2], ptr:ffffffbffd 3721e8 [ 42.651193] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d11808) Enabling DB DC Repeater 1 [ 42.651198] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 55: pdev(ffffffc034d11808) is_primary 0 [ 42.652581] wlan: [3815:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 542: cfg block ch annel list is empty [ 42.652586] wlan: [3815:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3850: pdev_idx = 1 tx_desc_limit = 0 [ 42.652600] wlan: [3815:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 42.652600] [ 42.652603] wlan: [3815:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 42.652603] [ 42.652607] wlan: [3815:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffff c02b622400 ic->ic_wrap_com=ffffffc02b622400 &wrap_com->wc_devt=ffffffc02b622400 [ 42.652607] [ 42.652622] wlan: [3815:I:ANY] __ol_ath_attach: 4485: needed_headroom reservation 60 [ 42.652634] wlan: [3815:I:ANY] wlan_cfg80211_init: 11680: Number of 2G channels: 11 [ 42.652746] wlan: [3815:I:ANY] ieee80211_cfg80211_radio_attach: 11806: ic: 0xffffffc03 0fa0880, wdev: 0xffffffc030fb8a58, wiphy: 0xffffffc034ff5aa0, netdev: 0xffffffc030fa0000 [ 42.653112] wlan: [3815:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3819 : Running with HW mode = 1 [ 42.653305] wlan: [3815:E:QLD] qld_register: 108: Handle or address is NULL [ 42.653318] wlan: [3815:I:ANY] wlan_pdev_operation: 726: num_radios=1, wifi_radios[0]. sc = ffffffc030f60880_radio_type = 2 [ 42.653322] wlan: [3815:I:ANY] wlan_pdev_operation: 726: num_radios=2, wifi_radios[1]. sc = ffffffc030fa0880_radio_type = 2 [ 42.653344] wlan: [3815:I:ANY] init_ath_pci_3_0: 179: 6ath_ol_pci_wifi3.0 : (Atheros/ multi-bss) [ 43.011809] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 14623: twt enabl ed. [ 43.011809] insmod wifi_2_0 [ 43.033399] wlan: [3820:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered f or target_type:0 with soc_ops:ffffffbffd938de0 [ 43.033842] wlan: [3820:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi -bss) insmod ath_pktlog insmod smart_antenna QCAWIFICFG80211 No Direct-Attach chipsets found. cfg80211tool wifi1 setCountry US [ 43.662756] wlan: [4231:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 11 [ 43.662830] wlan: [4231:I:ANY] number of channels: 2G = 11 5G = 0, 6G = 0 [ 43.669238] wlan: [4231:I:ANY] wlan_cfg80211_set_country: 6519: wlan_cfg80211_set_coun try: Country: US ret: 0 cfg80211tool wifi1 bsta_fixed_idmask 255 cfg80211tool wifi1 set_bcnburst 1 cfg80211tool wifi1 ce_debug_stats 1 cfg80211tool wifi1 sIgmpDscpOvrid 1 cfg80211tool wifi1 sIgmpDscpTidMap 6 cfg80211tool wifi1 enable_ol_stats 1 [ 43.809245] wlan: [4249:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max _mac_rings 1 [ 43.809313] wlan: [4249:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max _mac_rings 1 ifconfig wifi1 down [ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! cfg80211tool wifi1 setHwaddr B4:B0:24:59:B8:0E [ 43.842525] wlan: [4255:I:ANY] wlan_cfg80211_set_hwaddr: 6592: wlan_cfg80211_set_hwadd r :b4:b0:24:59:b8:0e ret: 0 ifconfig wifi1 up cfg80211tool wifi1 txbf_snd_int 100 [ 43.871625] wlan: [4260:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: val ue 100 wmi_status 0 cfg80211tool wifi1 obss_rssi_th 35 cfg80211tool wifi1 obss_rxrssi_th 35 cfg80211tool wifi1 dbdc_enable 0 [ 43.942217] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d11808) Enabling DB DC Repeater 0 cfg80211tool wifi1 no_vlan 1 cfg80211tool wifi1 discon_time 10 [ 43.992196] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 1 0 cfg80211tool wifi1 reconfig_time 60 [ 44.017214] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout val ue:60 sysctl -w dev.nss.n2hcfg.n2h_high_water_core0=67392 sysctl -w dev.nss.n2hcfg.n2h_wifi_pool_buf=40960 cfg80211tool wifi1 fc_buf0_max 16384 cfg80211tool wifi1 fc_buf1_max 16384 cfg80211tool wifi1 fc_buf2_max 16384 cfg80211tool wifi1 fc_buf3_max 32768 sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core0=256 sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core1=256 cfg80211tool wifi1 get_rxchainmask number of vifs: ath0 ath02 ifconfig wifi1 up wlanconfig ath0 create wlandev wifi1 wlanmode ap -cfg80211 iw phy phy1 interface add ath0 type __ap [ 44.328604] wlan: [4382:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 [ 44.328677] wlan: [4382:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create b4:b0:24:59:b8 :0e [ 44.339697] wlan: [4382:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030fa0880, op mode=IEEE80211_M_HOSTAP, flags=0x1 [ 44.339697] [ 44.347991] wlan: [4382:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1 [ 44.360190] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 44.367305] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b [ 44.382590] wlan: [4382:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 44.389377] wlan: [4382:I:ANY] MBO Initialized [ 44.403391] wlan: [4382:I:ANY] OCE Initialized [ 44.407926] wlan: [4382:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO: 1|LRO:0 [ 44.413312] wlan: [4382:I:ANY] VAP device ath0 created osifp: (ffffffc02d12a880) os_if : (ffffffc02a9d0000) cfg80211tool ath0 mode 11GHE40 cfg80211tool ath0 mode 11GHE40 cfg80211tool ath0 channel 0 cfg80211tool ath0 hide_ssid 0 cfg80211tool ath0 nrshareflag 7 cfg80211tool ath0 disablecoext 1 iw ath0 set 4addr on cfg80211tool ath0 wds 1 cfg80211tool ath0 backhaul 0 cfg80211tool ath0 uapsd 1 cfg80211tool ath0 vap_ind 0 cfg80211tool ath0 extap 0 iw ath0 set 4addr on cfg80211tool ath0 stafwd 0 cfg80211tool ath0 maxsta 128 [ 44.874157] wlan: [4446:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128 cfg80211tool ath0 blockdfschan 1 cfg80211tool ath0 twt_responder 0 cfg80211tool ath0 rrm 1 cfg80211tool ath0 vhtsubfee 1 cfg80211tool ath0 vhtmubfee 1 cfg80211tool ath0 vhtsubfer 1 cfg80211tool ath0 vhtmubfer 1 cfg80211tool ath0 he_subfee 1 [ 45.181418] wlan: [4473:I:ANY] wlan_set_param: 2964: HE SU BFEE already set with this value =1 cfg80211tool ath0 he_subfer 1 [ 45.223138] wlan: [4476:I:ANY] wlan_set_param: 2983: HE SU BFER already set with this value =1 cfg80211tool ath0 he_mubfee 1 [ 45.264096] wlan: [4479:I:ANY] ieee80211_ucfg_setparam: 4919: HE MU BFEE only supporte d in STA mode cfg80211tool ath0 he_mubfer 1 [ 45.305871] wlan: [4482:I:ANY] wlan_set_param: 3029: HE MU BFER already set with this value =1 cfg80211tool ath0 athnewind 1 iwpriv ath0 he_ulmumimo 0 [ 45.364080] wlan: [4493:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0|dl_muofdma_bfer:0 [ 45.364126] wlan: [4493:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x3b iwpriv ath0 he_ulofdma 0 [ 45.385664] wlan: [4496:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0|dl_muofdma_bfer:0 [ 45.387245] wlan: [4496:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x1b cfg80211tool ath0 ap_bridge 1 wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath0:/var/run/hostapd-ath0.conf [ 45.554826] device ath0 entered promiscuous mode [ 45.555292] br-lan: port 3(ath0) entered forwarding state [ 45.560034] br-lan: port 3(ath0) entered forwarding state [ 45.565933] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-0(ath0):ACS Params [ 45.570707] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0| vht_enabled:1|hw_mode:29|chwidth:20| [ 45.578243] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS starte d: vap:0xffffffc02a9d0000 [ 45.589234] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready ifconfig ath0 up iw phy phy1 set rts off wlanconfig ath02 create wlandev wifi1 wlanmode ap -cfg80211 iw phy phy1 interface add ath02 type __ap [ 45.728033] wlan: [4572:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath02 : clone params: 0x00000001 [ 45.728099] wlan: [4572:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create ba:b0:24:59:b8 :0e [ 45.739063] wlan: [4572:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030fa0880, op mode=IEEE80211_M_HOSTAP, flags=0x1 [ 45.739063] [ 45.747471] wlan: [4572:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1 [ 45.759699] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 45.766810] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b [ 45.782172] wlan: [4572:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 45.788883] wlan: [4572:I:ANY] MBO Initialized [ 45.802897] wlan: [4572:I:ANY] OCE Initialized [ 45.807438] wlan: [4572:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO: 1|LRO:0 [ 45.812772] wlan: [4572:I:ANY] VAP device ath02 created osifp: (ffffffc02d12c880) os_i f: (ffffffc02a480000) cfg80211tool ath02 mode 11GHE40 cfg80211tool ath02 mode 11GHE40 cfg80211tool ath02 channel 0 cfg80211tool ath02 hide_ssid 1 cfg80211tool ath02 dynamicbeacon 0 cfg80211tool ath02 disablecoext 1 iw ath02 set 4addr on cfg80211tool ath02 wds 1 cfg80211tool ath02 backhaul 0 cfg80211tool ath02 uapsd 1 cfg80211tool ath02 vap_ind 0 cfg80211tool ath02 extap 0 iw ath02 set 4addr on cfg80211tool ath02 stafwd 0 cfg80211tool ath02 maxsta 128 [ 46.269705] wlan: [4635:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128 cfg80211tool ath02 blockdfschan 1 cfg80211tool ath02 twt_responder 0 cfg80211tool ath02 rrm 1 cfg80211tool ath02 athnewind 1 cfg80211tool ath02 rept_spl 0 cfg80211tool ath02 ap_bridge 1 wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath02:/var/run/hostapd-ath02.conf [ 46.643233] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-1(ath02):ACS Params [ 46.643394] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0| vht_enabled:1|hw_mode:29|chwidth:20| [ 46.650864] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS starte d: vap:0xffffffc02a480000 ifconfig ath02 up iw phy phy1 set rts off qcawifi qcawificfg80211: enable radio wifi0 echo -n /ini > /sys/module/firmware_class/parameters/path update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 cfg80211tool wifi0 blockdfslist 1 cfg80211tool wifi0 setCountry US [ 47.380336] wlan: [5236:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4 [ 47.380792] wlan: [5236:I:ANY] wlan_scan_update_channel_list: 1135: num_chan: 4 [ 47.386497] wlan: [5236:I:ANY] number of channels: 2G = 0 5G = 4, 6G = 0 [ 47.393745] wlan: [5236:I:ANY] wlan_cfg80211_set_country: 6519: wlan_cfg80211_set_coun try: Country: US ret: 0 [ 47.400733] wlan: [941:I:ANY] ol_acfg_handle_wifi_ioctl: 446: ol_acfg_handle_wifi_ioct l: req->cmd=76 not valid for radio interface, it's for VAP cfg80211tool wifi0 bsta_fixed_idmask 255 cfg80211tool wifi0 set_bcnburst 1 cfg80211tool wifi0 ce_debug_stats 1 cfg80211tool wifi0 sIgmpDscpOvrid 1 cfg80211tool wifi0 sIgmpDscpTidMap 6 cfg80211tool wifi0 enable_ol_stats 1 [ 47.544745] wlan: [5254:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 2 Max _mac_rings 1 [ 47.544810] wlan: [5254:I:Monitor Filter] dp_mon_ht2_rx_ring_cfg: 119: srng type 1 Max _mac_rings 1 ifconfig wifi0 down cfg80211tool wifi0 setHwaddr B4:B0:24:59:B8:0F [ 47.577762] wlan: [5259:I:ANY] wlan_cfg80211_set_hwaddr: 6592: wlan_cfg80211_set_hwadd r :b4:b0:24:59:b8:0f ret: 0 ifconfig wifi0 up cfg80211tool wifi0 txbf_snd_int 100 [ 47.606606] wlan: [5264:I:ANY] ol_ath_set_config_param: 1640: set TXBF_SND_PERIOD: val ue 100 wmi_status 0 cfg80211tool wifi0 obss_rssi_th 35 cfg80211tool wifi0 obss_rxrssi_th 35 cfg80211tool wifi0 dbdc_enable 0 [ 47.677158] wlan: [0:I:ANY] dp_lag_soc_enable: 102: pdev(ffffffc034d12008) Enabling DB DC Repeater 0 cfg80211tool wifi0 no_vlan 1 cfg80211tool wifi0 discon_time 10 [ 47.727734] wlan: [0:I:ANY] ol_ath_set_config_param: 2377: Disconnect_timeout value: 1 0 cfg80211tool wifi0 reconfig_time 60 [ 47.752684] wlan: [0:I:ANY] ol_ath_set_config_param: 2383: Reconfiguration_timeout val ue:60 cfg80211tool wifi0 fc_buf0_max 32768 cfg80211tool wifi0 fc_buf1_max 32768 cfg80211tool wifi0 fc_buf2_max 32768 cfg80211tool wifi0 fc_buf3_max 32768 sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core0=256 sysctl -w dev.nss.n2hcfg.n2h_queue_limit_core1=256 cfg80211tool wifi0 get_rxchainmask number of vifs: ath1 ath12 ifconfig wifi0 up wlanconfig ath1 create wlandev wifi0 wlanmode ap -cfg80211 iw phy phy0 interface add ath1 type __ap [ 47.999653] wlan: [5377:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath1 : clone params: 0x00000001 [ 47.999719] wlan: [5377:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create b4:b0:24:59:b8 :0f [ 48.010682] wlan: [5377:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030f60880, op mode=IEEE80211_M_HOSTAP, flags=0x1 [ 48.010682] [ 48.019026] wlan: [5377:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1 [ 48.031266] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 48.038337] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b [ 48.053656] wlan: [5377:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 48.060423] wlan: [5377:I:ANY] MBO Initialized [ 48.074431] wlan: [5377:I:ANY] OCE Initialized [ 48.078971] wlan: [5377:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO: 1|LRO:0 [ 48.084652] wlan: [5377:I:ANY] VAP device ath1 created osifp: (ffffffc02b302880) os_if : (ffffffc02a4a8000) cfg80211tool ath1 mode 11AHE80 cfg80211tool ath1 mode 11AHE80 cfg80211tool ath1 channel 0 cfg80211tool ath1 hide_ssid 0 cfg80211tool ath1 nrshareflag 7 cfg80211tool ath1 disablecoext 1 iw ath1 set 4addr on cfg80211tool ath1 wds 1 cfg80211tool ath1 backhaul 0 cfg80211tool ath1 uapsd 1 cfg80211tool ath1 vap_ind 0 cfg80211tool ath1 extap 0 iw ath1 set 4addr on cfg80211tool ath1 amsdu 2 cfg80211tool ath1 stafwd 0 cfg80211tool ath1 maxsta 128 [ 48.577306] wlan: [5445:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128 cfg80211tool ath1 blockdfschan 1 cfg80211tool ath1 twt_responder 0 cfg80211tool ath1 rrm 1 cfg80211tool ath1 vhtsubfee 1 cfg80211tool ath1 vhtmubfee 1 cfg80211tool ath1 vhtsubfer 1 cfg80211tool ath1 vhtmubfer 1 [ flowstat_get_wwan_tx_rx_statistics ] 136: Get Rx/Tx flow from qmi failed! cfg80211tool ath1 he_subfee 1 [ 48.884830] wlan: [5472:I:ANY] wlan_set_param: 2964: HE SU BFEE already set with this value =1 cfg80211tool ath1 he_subfer 1 [ 48.926217] wlan: [5475:I:ANY] wlan_set_param: 2983: HE SU BFER already set with this value =1 cfg80211tool ath1 he_mubfee 1 [ 48.967891] wlan: [5478:I:ANY] ieee80211_ucfg_setparam: 4919: HE MU BFEE only supporte d in STA mode cfg80211tool ath1 he_mubfer 1 [ 48.980674] ieee80211_acs_find_best_11ng_centerchan: acs_11ngbestchan = 11 [ 48.980704] 2.4G Best Channel Selected 10 rssi 0 nf -97 [ 48.986628] wlan: [2583:I:ANY] vap-0(ath0): ACS result PCH 10 freq 2457, SCH 6 freq 24 37, hw_mode 1 chwidth 40, vht_seg0 8 freq 2447, vht_seg1 0 freq 0 [ 48.991906] wlan: [2583:I:ANY] vap-1(ath02): ACS result PCH 10 freq 2457, SCH 6 freq 2 437, hw_mode 1 chwidth 40, vht_seg0 8 freq 2447, vht_seg1 0 freq 0 [ 49.005414] wlan: [2583:I:ANY] ieee80211_acs_scan_evhandler: 3885: lock held duration: 25(ms) [ 49.023510] wlan: [5481:I:ANY] wlan_set_param: 3029: HE MU BFER already set with this value =1 [ 49.027754] wlan: [954:I:ANY] DES SSID SET=deco [ 49.036448] wlan: [954:I:ANY] wlan_cfg80211_chan_to_phymode: 1239: wlan_cfg80211_chan_ to_phymode: band:0 width: 2 channel_cfreq: 2457 center_freq1: 2447 chandef.center_freq2: 0 flags: 0 [ 49.040808] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 49.040808] Channel is configured already!! cfg80211tool ath1 athnewind 1 [ 49.082772] wlan: [0:I:CMN_MLME] vdev[0] ieee chan:10 freq:2457 [ 49.082984] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 49.082984] FD Interval should be a factor of BI. [ 49.082984] Disabling FD [ 49.082984] [ 49.087606] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 49.087606] FD Interval should be a factor of BI. [ 49.087606] Disabling FD [ 49.087606] [ 49.094846] wlan: [954:I:ANY] DES SSID SET=zEQQkhpPcoaHsP34 [ 49.094851] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 27 [ 49.094902] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 49.094902] Channel is configured already!! [ 49.140523] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps) [ 49.151148] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps) [ 49.157119] wlan: [0:I:CMN_MLME] vdev[1] ieee chan:10 freq:2457 [ 49.162023] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 49.162023] FD Interval should be a factor of BI. [ 49.162023] Disabling FD [ 49.162023] [ 49.167624] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 49.167624] FD Interval should be a factor of BI. [ 49.167624] Disabling FD [ 49.167624] [ 49.187716] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps) [ 49.207562] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps) iwpriv ath1 he_ulmumimo 0 [ 49.222651] wlan: [5493:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0|dl_muofdma_bfer:0 [ 49.222697] wlan: [5493:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x3b iwpriv ath1 he_ulofdma 0 [ 49.244336] wlan: [5496:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0|dl_muofdma_bfer:0 [ 49.245799] wlan: [5496:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x1b cfg80211tool ath1 ap_bridge 1 wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath1:/var/run/hostapd-ath1.conf [ 49.415427] device ath1 entered promiscuous mode [ 49.416121] br-lan: port 4(ath1) entered forwarding state [ 49.420859] br-lan: port 4(ath1) entered forwarding state [ 49.426574] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-2(ath1):ACS Params [ 49.431535] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0| vht_enabled:1|hw_mode:30|chwidth:20| [ 49.439165] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS starte d: vap:0xffffffc02a4a8000 ifconfig ath1 up iw phy phy0 set rts off wlanconfig ath12 create wlandev wifi0 wlanmode ap -cfg80211 iw phy phy0 interface add ath12 type __ap [ 49.571427] wlan: [5571:I:ANY] wlan_cfg80211_add_virtual_intf: 335: proprietary mode 6 for interface: ath12 : clone params: 0x00000001 [ 49.571493] wlan: [5571:I:ANY] osifp_create_wlan_vap: 9626: VDEV Create ba:b0:24:59:b8 :0f [ 49.582543] wlan: [5571:I:ANY] wlan_vap_create: 1600: devhandle=0xffffffc030f60880, op mode=IEEE80211_M_HOSTAP, flags=0x1 [ 49.582543] [ 49.590914] wlan: [5571:I:ANY] ol_ath_vap_set_param: 1209: Setting SGI value: 1 [ 49.603112] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2241: VDEV params:HE su_bfee:1|su _bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1|dl_muofdma_bfer:0 [ 49.610233] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2254: he_bf_cap=0x7b [ 49.625489] wlan: [5571:I:ANY] ol_ath_vap_set_param: 2269: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 49.632266] wlan: [5571:I:ANY] MBO Initialized [ 49.646335] wlan: [5571:I:ANY] OCE Initialized [ 49.650827] wlan: [5571:I:ANY] osif_create_vap_complete: 9834: TX Checksum:1|SG:1|TSO: 1|LRO:0 [ 49.656551] wlan: [5571:I:ANY] VAP device ath12 created osifp: (ffffffc02b304880) os_i f: (ffffffc02a580000) cfg80211tool ath12 mode 11AHE80 cfg80211tool ath12 mode 11AHE80 cfg80211tool ath12 channel 0 cfg80211tool ath12 hide_ssid 1 cfg80211tool ath12 dynamicbeacon 0 cfg80211tool ath12 disablecoext 1 iw ath12 set 4addr on cfg80211tool ath12 wds 1 cfg80211tool ath12 backhaul 0 cfg80211tool ath12 uapsd 1 cfg80211tool ath12 vap_ind 0 cfg80211tool ath12 extap 0 iw ath12 set 4addr on cfg80211tool ath12 stafwd 0 cfg80211tool ath12 maxsta 128 [ 50.113671] wlan: [5634:I:ANY] ieee80211_ucfg_setparam: 1536: Setting Max Stations:128 cfg80211tool ath12 blockdfschan 1 cfg80211tool ath12 twt_responder 0 cfg80211tool ath12 rrm 1 cfg80211tool ath12 athnewind 1 cfg80211tool ath12 rept_spl 0 cfg80211tool ath12 ap_bridge 1 wpa_cli -g /var/run/hostapd/global raw ADD bss_config=ath12:/var/run/hostapd-ath12.conf [ 50.498032] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3709: vap-3(ath12):ACS Params [ 50.498858] wlan: [954:I:ANY] wlan_cfg80211_do_acs: 3712: ht_enabled:1|ht40_enabled:0| vht_enabled:1|hw_mode:30|chwidth:20| [ 50.506392] wlan: [954:I:ANY] ieee80211_autoselect_infra_bss_channel: 4151: ACS starte d: vap:0xffffffc02a580000 ifconfig ath12 up iw phy phy0 set rts off [ 50.545215] Not a Hy-Fi device, or device not found: br-iptv [ 50.545696] Not a Hy-Fi device, or device not found: br-iptv qcawifi qcawificfg80211: enable radio wifi2 echo -n /ini > /sys/module/firmware_class/parameters/path update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 [ 50.708326] wlan: [2583:I:ANY] vap-2(ath1): ACS result PCH 48 freq 5240, SCH 36 freq 5 180, hw_mode 2 chwidth 80, vht_seg0 42 freq 5210, vht_seg1 0 freq 0 [ 50.708431] wlan: [2583:I:ANY] vap-3(ath12): ACS result PCH 48 freq 5240, SCH 36 freq 5180, hw_mode 2 chwidth 80, vht_seg0 42 freq 5210, vht_seg1 0 freq 0 [ 50.721318] wlan: [2583:I:ANY] ieee80211_acs_scan_evhandler: 3885: lock held duration: 13(ms) [ 50.744494] wlan: [954:I:ANY] DES SSID SET=deco [ 50.744523] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30 [ 50.747968] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 50.747968] Channel is configured already!! [ 50.784793] wlan: [0:I:CMN_MLME] vdev[2] ieee chan:48 freq:5240 [ 50.785015] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 50.785015] FD Interval should be a factor of BI. [ 50.785015] Disabling FD [ 50.785015] [ 50.789681] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 50.789681] FD Interval should be a factor of BI. [ 50.789681] Disabling FD [ 50.789681] [ 50.793247] wlan: [954:I:ANY] DES SSID SET=zEQQkhpPcoaHsP34 [ 50.793254] wlan: [954:I:ANY] wlan_cfg80211_set_phymode: 1215: desired hw mode: 30 [ 50.793353] wlan: [954:I:ANY] ieee80211_ucfg_set_freq_internal: 553: [ 50.793353] Channel is configured already!! [ 50.793539] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel_for_freq: 879: dfs_curchan already updated [ 50.853264] wlan: [0:I:ANY] vdev[2]: Mgt Rate:6000(kbps) [ 50.863910] wlan: [0:I:ANY] vdev[2]: Mgt Rate:6000(kbps) [ 50.870219] wlan: [0:I:CMN_MLME] vdev[3] ieee chan:48 freq:5240 [ 50.874794] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 50.874794] FD Interval should be a factor of BI. [ 50.874794] Disabling FD [ 50.874794] [ 50.880377] wlan: [0:E:FILS discovery] wlan_fd_set_valid_fd_period: 607: Invalid FD In terval : 0. Valid range is 20 - 100ms. [ 50.880377] FD Interval should be a factor of BI. [ 50.880377] Disabling FD [ 50.880377] [ 50.900504] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps) [ 50.920355] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps) echo q6mem > /sys/bus/coresight/devices/coresight-tmc-etr/out_mode echo 1 > /sys/bus/coresight/devices/coresight-tmc-etr/curr_s[ 51.492436] coresight-funn el 6130000.funnel: FUNNEL inport 5 enabled [ 51.497337] coresight-funnel 6021000.funnel: FUNNEL inport 6 enabled [ 51.504745] coresight-tmc 6028000.tmc: TMC enabled [ 51.507606] coresight-replicator-qcom 6026000.replicator: REPLICATOR enabled [ 51.512209] coresight-tmc 6027000.tmc: TMC enabled [ 51.519421] coresight-funnel 6021000.funnel: FUNNEL inport 7 enabled [ 51.524056] coresight-stm 6002000.stm: STM tracing enabled ink echo 5 > /sys/bus/coresight/devices/coresight-funnel-mm/funnel_ctrl echo 6 > /sys/bus/coresight/devices/coresight-funnel-in0/funnel_ctrl echo 1 > /sys/bus/coresight/devices/coresight-stm/enable *****QDSS Tracing Configuration completed******* echo -e qdss_trace_load_config\nqdss_trace_start\nquit\n > /tmp/qdss_trace_commands ******Starting cnss_cli******** whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifi whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.1 does not exist, add it. [ 51.914077] device ath12.1 entered promiscuous mode [ 51.918134] device ath12 entered promiscuous mode [ 51.918530] br-lan: port 5(ath12.1) entered forwarding state [ 51.922681] br-lan: port 5(ath12.1) entered forwarding state interface2g:ath02 whc (repacd): ath02.1 does not exist, add it. [ 51.972094] device ath02.1 entered promiscuous mode [ 51.976114] device ath02 entered promiscuous mode [ 51.976401] br-lan: port 6(ath02.1) entered forwarding state [ 51.980689] br-lan: port 6(ath02.1) entered forwarding state whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:2 backhual_iface:wifi whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.2 does not exist, add it. [ 52.094301] device ath12.2 entered promiscuous mode [ 52.097019] br-lan: port 7(ath12.2) entered forwarding state [ 52.098003] br-lan: port 7(ath12.2) entered forwarding state interface2g:ath02 whc (repacd): ath02.2 does not exist, add it. [ 52.149687] device ath02.2 entered promiscuous mode [ 52.152646] br-lan: port 8(ath02.2) entered forwarding state [ 52.153387] br-lan: port 8(ath02.2) entered forwarding state whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:2 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): set wifi done flag whc (repacd): unlock whc_wifi_config_lock whc (repacd): get whc_wifi_config_lock whc (repacd): clear wifi_set_done flag whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: lan whc (repacd): Device type: AP whc (repacd): Sysmode: Router whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert _state wifi guest enable) whc (repacd): Using SON mode for GW Connected AP whc (repacd): __repacd_restart_dependencies: No changes; not restarting network stack... whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifi whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.1 already existed, do nothing. interface2g:ath02 whc (repacd): ath02.1 already existed, do nothing. whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:2 backhual_iface:wifi whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.2 already existed, do nothing. interface2g:ath02 whc (repacd): ath02.2 already existed, do nothing. whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:2 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): set wifi done flag whc (repacd): unlock whc_wifi_config_lock [aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 [aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 [ flowstat_start_timer ] 677: ===> last_up_time=0 iptv.init start iptv iptv start_service switch: reset_wan_vlan: select p4: 1 switch: reset_wan_vlan: select p5: 2 mac:B4-B0-24-59-B8-0C 1 cap_mac: 1 [ 54.394821] ivalue value: [ 54.394842] bind_divece_num:1 [ 7432] [init 340] init nds:0x0 wanDetect: INFO: wandetect_get_profile_eths: wanDetect: INFO: eth0 wanDetect: INFO: eth1 [ 7432] [dns_proxy_execFormatCmd 88] cmd: nat del dns wanDetect: INFO: my device_id : 80198A32723C173A21C35791744A5A151F4D05B6 wanDetect: INFO: init_no_wan_mode wanDetect: INFO: clear_dialed_flag wanDetect: INFO: move all interface to br-lan wanDetect: INFO: move eth0 to br-lan... [ 7432] [dns_proxy_execFormatCmd 88] cmd: nat add dns { 192.168.68.1 0.0.0.0 } conn-indicator: INFO: -- running -- conn-indicator: NOTE: BINDING state: -1 -> 3 conn-indicator: INFO: <30000307> Invoke led: conn[2] conn-indicator: NOTE: Mode changed: Unknown -> Router conn-indicator: NOTE: Role changed: Unknown -> FAP conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST conn-indicator: NOTE: Network type: Unknown -> FAP conn-indicator: INFO: <31330307> Invoke led: conn[1] conn-indicator: NOTE: Connectivity changed: FAP.LOST(0x7) -> OFFLINE(0x1) wandetect: move eth0 to other bridge wandetect: move eth0 to lan bridge device eth0 is not a slave of br-wan device eth0 is already a member of a bridge; can't enslave it to bridge br-lan. ===== TIPC have already enabled ==== [ 7432] [dns_proxy_execFormatCmd 88] cmd: nat add dns { 0.0.0.0 0.0.0.0 } wanDetect: INFO: move eth1 to br-lan... [ 7432] [main 481] init done, now do uloop_run [ 54.716004] Started in network mode [ 54.716031] Own node address <224.3584.1>, network identity 4711 [ 54.725041] Enabled bearer <deco:br-lan:1>, discovery domain <224.3584.0>, priority 10 wandetect: move eth1 to other bridge wandetect: move eth1 to lan bridge device eth1 is not a slave of br-wan device eth1 is already a member of a bridge; can't enslave it to bridge br-lan. wanDetect: INFO: Goto uloop_run tipc-server: INFO: -- running -- tipc-server: INFO: server radar: port {18888,100,200} created tipc-server: INFO: mode is AP tipc-server: INFO: mode is AP tipc-server: INFO: server AP: port {5000,100,100} created tipc-server: INFO: mode is AP [ 54.784496] Not a Hy-Fi device, or device not found: br-iptv [ 54.786621] Not a Hy-Fi device, or device not found: br-iptv conn-indicator: INFO: Notify inet.down json_object_from_file: error reading file /tmp/sync-server/mesh_dev_list: No such file or directory smart_home_schedule reload_service maclist_smart_home: #### no schedule client found in blacklist config #### [ 55.072358] S95done (7851): drop_caches: 3 conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST manager permission has been set, no need to set again guest-eth: Start to set guest vlan guest-eth: Ignore system signal guest-eth: Lock vlan.lock guest-eth: AP role, eth0 eth1 set tag port, vlan id is 591 guest-eth: add eth if eth0.591 [ 56.215089] device eth0.591 entered promiscuous mode [ 56.222165] IPv6: ADDRCONF(NETDEV_UP): eth0.591: link is not ready guest-eth: add eth if eth1.591 [ 56.239741] device eth1.591 entered promiscuous mode [ 56.246461] IPv6: ADDRCONF(NETDEV_UP): eth1.591: link is not ready mac:B4-B0-24-59-B8-0C role:AP update fap: B4:B0:24:59:B8:0C [ 56.389241] net rmnet_mhi0: link_state 0x0 -> 0x1 [ 56.391828] IPv6: ADDRCONF(NETDEV_CHANGE): rmnet_mhi0: link becomes ready [ 56.393075] IPv6: ADDRCONF(NETDEV_CHANGE): rmnet_mhi0.1: link becomes ready conn-indicator: INFO: <31330301> link event: rmnet_mhi0.upwanDetect: INFO: --> link event : rmnet_mhi0.up wanDetect: INFO: ! mode_need_dial conn-indicator: INFO: <31330301> link event: rmnet_mhi0.1.up wanDetect: INFO: --> link event: rmnet_mhi0.1.up wanDetect: INFO: ! mode_need_dial conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST *****/tmp/ipv6_firewall/op_rule_id file not found, create it.***** [ 56.974641] Not a Hy-Fi device, or device not found: br-iptv [ 56.974734] Not a Hy-Fi device, or device not found: br-iptv [ 3366(lan)] [smartip_ibus_handle_wifi_event 2289] smartipd handle wifi event:9 [ 3366(lan)] [smartip_ibus_handle_wifi_event 2313] RE -> AP [ 3366(lan)] [smartip_ibus_handle_dhcp_server_changed 2204] DHCP Server changed [ 3366(lan)] [smartip_ibus_handle_dhcp_server_changed 2238] Restart dhcpd [ 3366(lan)] [smartip_kill_process 271] kill process udhcpd conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST [ 3366(lan)] [smartip_start_process 366] start udhcpd [ 3366(lan)] [smartip_check_lan_wan_is_samesubnet 2800] br-wan has no ip! [ 3366(lan)] [smartip_ibus_handle_wifi_event 2343] Change to FAP, Update Lan IP [ 3366(lan)] [smartip_notify_lan_update 1320] Notify the lan ip changed. [ 3366(lan)] [smartip_update_lanip 593] config IP: ifconfig br-lan 192.168.68.1 netmask 255.255.252.0 [ 3366(lan)] [smartip_update_lanip 604] route del default dev br-lan [ 58.561785] work mode change to :AP [ 58.561785] [ 58.564769] get dev num:2 [ 58.566301] statistics: SET_STA_DEVICE dev_name=eth0 [ 58.566304] statistics: SET_STA_DEVICE dev_name=eth1 [ 58.566308] backhaul sta dev num:2 conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST start minitor config flowstat_send_test_sms [ 3366(lan)] [smartip_update_lanip 622] restart miniupnpd parental-control_avira: Restart the avira homecare [ 8728(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:UPDATE start minitor config mobile_config [ 8849(lan)] [smartip_call_hotplug_ip 2032] Send Message -- TYPE:lan, EVENT:FAPIPUPDATE not found in config echo 0 to init ===parental_control_avira=== no need to start [aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 false 0 start minitor config profile_action [aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 IPConflict2 mask:22 lan_addr:192.168.68.1 mask_str:255.255.252.0 IPConflict2 mask:22 IPConflict2 old_mask:255.255.252.0 old_ip:192.168.68.1 [ 3366(lan)] [smartip_update_lanip 634] restart domain_login [ 59.375519] Not a Hy-Fi device, or device not found: br-iptv [ 59.375636] Not a Hy-Fi device, or device not found: br-iptv qos_v2 disable gro qos_v2 start conn-indicator: ERR: [validate_dir] stat(/tmp/sync-server): No such file or directory conn-indicator: ERR: Invalid directory: /tmp/sync-server conn-indicator: ERR: Failed to watch /tmp/sync-server/mesh_dev_list conn-indicator: ERR: Failed to allocate DEV_LIST wanDetect: ERR: port update : eth0 /lib/sync-server/scripts/detect-re:35: error open file failed:/var/run/record_devid /lib/sync-server/scripts/detect-re:35: error open file failed:/tmp/sync-server/mesh_dev_ list /lib/sync-server/scripts/detect-re:57: error: record_devid or mesh_dev_list is nil, do n othing conn-indicator: ERR: [file_md5sum] fopen(/tmp/sync-server/mesh_dev_list): No such file or directory json_object_from_file: error reading file /tmp/sync-server/mesh_dev_list: No such file or directory conn-indicator: ERR: [update_devlist] Failed to parse /tmp/sync-server/mesh_dev_list: No such file or directory [ 60.738621] mode:0 /lib/sync-server/scripts/probe:228: error open file failed:/var/run/record_devid /lib/sync-server/scripts/probe:748: to_get_info 80198A32723C173A21C35791744A5A151F4D0 5B6 first, clean old record data /lib/sync-server/scripts/probe:752: to_get_info 80198A32723C173A21C35791744A5A151F4D0 5B6 ========= MODE: cloud_awn_update begin ========== mode: AP Ipv6 Firewall config trigger stop! qos_v2 stop ========= MODE: update awn feature info to cloud ========== --------->exiting qos /lib/sync-server/scripts/probe:861: to_get_info: ["192.168.68.1","1"] conn-indicator: ERR: [update_devlist] Failed to parse /tmp/sync-server/mesh_dev_list: Res ource temporarily unavailable /lib/sync-server/scripts/get-info:84: Total 1 devices need to get info sync_get_info begin() sync_get_compatible_info sync_get_info end() error open file failed:/var/run/record_devid error open file failed:/var/run/record_op error open file failed:/var/run/record_cfg error open file failed:/var/run/record_component_router_owner error open file failed:/var/run/record_component_router_user error open file failed:/var/run/record_component_ap_owner error open file failed:/var/run/record_component_ap_user error open file failed:/var/run/record_opcode_cfg error open file failed:/var/run/record_devid error open file failed:/tmp/check_dev error open file failed:/var/run/record_component_whole update_compitable_list can't support IOT /lib/sync-server/scripts/get-info:92: Total 1 devices were got info successfully error open file failed:/var/run/lookup_cfg there is no iot fap error open file failed:/var/run/lookup_op check_opcode_iot fap has no iot /lib/sync-server/scripts/get-info:104: Total 1 devices need to get cfg req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5 A151F4D05B6"}} qos_v2 disable gro qos_v2 start sync_get_cfg begin() Warning! can't find cfg : white_list_1 sync_get_cfg end() error open file failed:/tmp/merge_cfgs /lib/sync-server/scripts/get-info:106: Total 1 devices were got cfg successfully /lib/sync-server/scripts/get-info:121: merge_cfgs is nil , don't update user_config. Total 1 devices need to update dev list Total 1 devices were update dev list successfully re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5 A151F4D05B6"}} re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5 A151F4D05B6"}} re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ====== notify_check_client: current time is 1681133532 req: {"method":"getDeviceUserInfo","params":{"deviceId":"80198A32723C173A21C35791744A5 A151F4D05B6"}} client triggers is opened. re: -3002 get_deviceUserInfo: request error ======= ERROR: get cloudUserName from cloud failed ======


Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00158 S - IMAGE_VARIANT_STRING=HAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e5 B - 201 - PBL, Start B - 2736 - bootable_media_detect_entry, Start B - 3443 - bootable_media_detect_success, Start B - 3448 - elf_loader_entry, Start B - 6114 - auth_hash_seg_entry, Start B - 6357 - auth_hash_seg_exit, Start B - 68340 - elf_segs_hash_verify_entry, Start B - 131183 - PBL, End B - 217617 - SBL1, Start B - 296917 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 306799 - pm_device_init, Start B - 489891 - PM_SET_VAL:Skip D - 181170 - pm_device_init, Delta B - 492300 - pm_driver_init, Start D - 5368 - pm_driver_init, Delta B - 498675 - clock_init, Start D - 2135 - clock_init, Delta B - 502609 - boot_flash_init, Start D - 12566 - boot_flash_init, Delta B - 518957 - boot_config_data_table_init, Start D - 3111 - boot_config_data_table_init, Delta - (575 Bytes) B - 526460 - Boot Setting : 0x00000618 B - 530364 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:4,Sub type:0 B - 537288 - sbl1_ddr_set_params, Start B - 541100 - CPR configuration: 0x30c B - 544455 - cpr_init, Start B - 547353 - Rail:0 Mode: 5 Voltage: 792000 B - 552446 - CL CPR settled at 744000mV B - 555283 - Rail:1 Mode: 5 Voltage: 880000 B - 559553 - Rail:1 Mode: 7 Voltage: 888000 D - 16531 - cpr_init, Delta B - 566354 - Pre_DDR_clock_init, Start B - 570472 - Pre_DDR_clock_init, End B - 573766 - DDR Type : PCDDR3 B - 579500 - do ddr sanity test, Start D - 1067 - do ddr sanity test, Delta B - 584258 - DDR: Start of HAL DDR Boot Training B - 588985 - DDR: End of HAL DDR Boot Training B - 594689 - DDR: Checksum to be stored on flash is 1377291785 B - 604998 - Image Load, Start D - 224358 - QSEE Image Loaded, Delta - (1376448 Bytes) B - 829447 - Image Load, Start D - 61 - SEC Image Loaded, Delta - (0 Bytes) B - 837133 - Image Load, Start D - 10706 - DEVCFG Image Loaded, Delta - (26008 Bytes) B - 847930 - Image Load, Start D - 22021 - RPM Image Loaded, Delta - (86584 Bytes) B - 870043 - Image Load, Start D - 108915 - APPSBL Image Loaded, Delta - (672668 Bytes) B - 979111 - QSEE Execution, Start D - 91 - QSEE Execution, Delta B - 984906 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 991280 - SBL1, End D - 775981 - SBL1, Delta S - Flash Throughput, 6744 KB/s (2162955 Bytes, 320702 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 1651 MHz U-Boot 2016.01 (Feb 25 2021 - 20:16:45 +0800) DRAM: smem ram ptable found: ver: 1 len: 4 1 GiB NAND: Could not find nand_gpio in dts, using defaults ONFI device found ID = 158061c8 Vendor = c8 Device = 61 SF: Unsupported flash IDs: manuf 00, jedec 1c78, ext_jedec 4a74 ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB MMC: <NULL>: 0 PCI0 is not defined in the device tree PCI1 is not defined in the device tree In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 machid: 8010400 Card did not respond to voltage select! eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid eth2 MAC Address from ART is not valid eth3 MAC Address from ART is not valid eth4 MAC Address from ART is not valid eth5 MAC Address from ART is not valid gpio 38 set BOARD_3V9_5V_EN_GPIO to high[1] gpio 64 set PHY_QCA8081_1V8_EN_GPIO to high[1] gpio 33 set PHY_AR8033_3V3_EN_GPIO to high[1] gpio 35 set ONOFF_MODULE_5G_GPIO to low[0] ... 1s gpio 35 set ONOFF_MODULE_5G_GPIO to high[1] ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 9 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 15/8, WL threshold: 4096, image sequenc e number: 1097309032 ubi0: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for b ad PEB handling: 20 Find no boot alter flag! Enter magic string to stop autoboot in 1 seconds Unmounting UBIFS volume ubi_factory_data! ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 42 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 473343929 ubi0: available PEBs: 0, total reserved PEBs: 336, PEBs reserved for bad PEB handling: 20 Read 0 bytes from volume kernel to 44000000 No size specified -> Using max size (5332992) ## Loading kernel from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-6.6.44 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 5177696 Bytes = 4.9 MiB Architecture: AArch64 OS: Linux Load Address: 0x41000000 Entry Point: 0x41000000 Hash algo: crc32 Hash value: 7967ebe7 Hash algo: sha1 Hash value: 8fd37f2833dafd0dfed3db92f120db3e04416d79 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 44000000 ... Using 'config@hk01.c5' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt tplink_x80-5g device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x444f0388 Data Size: 46489 Bytes = 45.4 KiB Architecture: AArch64 Hash algo: crc32 Hash value: abe3e37d Hash algo: sha1 Hash value: 8dfcddfc3942742eadc498f05b143cc0b771d139 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x444f0388 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3f1000, end 4a3ff598 ... OK Could not find PCI in device tree Using machid 0x8010400 from environment Starting kernel ... Jumping to AARCH64 kernel via monitor [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034 ] [ 0.000000] Linux version 6.6.44 (professor_jonny@MRSPARKLE) (aarc h64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26970-e6c9264351) 13. 3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Mon Aug 12 18:49:30 2024 [ 0.000000] Machine model: tplink x80-5g [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffff ff (16384 KiB) nomap non-reusable nss@40000000 [ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fff ff (2048 KiB) nomap non-reusable tzapp@4a400000 [ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fff ff (4096 KiB) nomap non-reusable bootloader@4a600000 [ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafff ff (1024 KiB) nomap non-reusable sbl@4aa00000 [ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfff ff (1024 KiB) nomap non-reusable smem@4ab00000 [ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affff ff (4096 KiB) nomap non-reusable memory@4ac00000 [ 0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efff ff (97280 KiB) nomap non-reusable wcnss@4b000000 [ 0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffff ff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000 [ 0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fff ff (1024 KiB) nomap non-reusable m3_dump@51000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff ] [ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff ] [ 0.000000] node 0: [mem 0x000000004a400000-0x00000000510fffff ] [ 0.000000] node 0: [mem 0x0000000051100000-0x000000007fffffff ] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x0000000 07fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 18 pages/cpu s35240 r8192 d30296 u737 28 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootf s rootfstype=squashfs rootwait root=/dev/ubiblock0_1 [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 104 8576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 52428 8 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:of f [ 0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted t o 1MB [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x0000 00007ec00000] (1MB) [ 0.000000] Memory: 885772K/1048576K available (8128K kernel code, 892K rwdata, 2500K rodata, 1472K init, 276K bss, 162804K reserved, 0 K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nod es=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment dela y is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479] [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on con tention. [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000129] Calibrating delay loop (skipped), value calculated usi ng timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000142] pid_max: default: 32768 minimum: 301 [ 0.005160] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.005174] Mountpoint-cache hash table entries: 2048 (order: 2, 1 6384 bytes, linear) [ 0.009416] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_t ask_cb_adjust=1. [ 0.009641] rcu: Hierarchical SRCU implementation. [ 0.009646] rcu: Max phase no-delay instances is 1000. [ 0.010569] smp: Bringing up secondary CPUs ... [ 0.011229] Detected VIPT I-cache on CPU1 [ 0.011332] CPU1: Booted secondary processor 0x0000000001 [0x410fd 034] [ 0.012001] Detected VIPT I-cache on CPU2 [ 0.012070] CPU2: Booted secondary processor 0x0000000002 [0x410fd 034] [ 0.012721] Detected VIPT I-cache on CPU3 [ 0.012786] CPU3: Booted secondary processor 0x0000000003 [0x410fd 034] [ 0.012855] smp: Brought up 1 node, 4 CPUs [ 0.012863] SMP: Total of 4 processors activated. [ 0.012869] CPU features: detected: 32-bit EL0 Support [ 0.012874] CPU features: detected: CRC32 instructions [ 0.012943] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.012950] CPU: All CPU(s) started at EL1 [ 0.012953] alternatives: applying system-wide alternatives [ 0.023013] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xf fffffff, max_idle_ns: 19112604462750000 ns [ 0.023042] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.024776] pinctrl core: initialized pinctrl subsystem [ 0.026479] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027055] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic a llocations [ 0.027098] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.027132] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool fo r atomic allocations [ 0.027519] thermal_sys: Registered thermal governor 'step_wise' [ 0.027576] cpuidle: using governor menu [ 0.027779] ASID allocator initialised with 65536 entries [ 0.054062] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.056925] Modules: 29408 pages in range for non-PLT usage [ 0.056933] Modules: 520928 pages in range for PLT usage [ 0.061698] SCSI subsystem initialized [ 0.061902] usbcore: registered new interface driver usbfs [ 0.061937] usbcore: registered new interface driver hub [ 0.061985] usbcore: registered new device driver usb [ 0.062436] qcom_scm: convention: smc arm 64 [ 0.064085] clocksource: Switched to clocksource arch_sys_counter [ 0.067864] NET: Registered PF_INET protocol family [ 0.068014] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.070595] tcp_listen_portaddr_hash hash table entries: 512 (orde r: 1, 8192 bytes, linear) [ 0.070618] Table-perturb hash table entries: 65536 (order: 6, 262 144 bytes, linear) [ 0.070633] TCP established hash table entries: 8192 (order: 4, 65 536 bytes, linear) [ 0.070720] TCP bind hash table entries: 8192 (order: 6, 262144 by tes, linear) [ 0.070992] TCP: Hash tables configured (established 8192 bind 819 2) [ 0.071095] UDP hash table entries: 512 (order: 2, 16384 bytes, li near) [ 0.071133] UDP-Lite hash table entries: 512 (order: 2, 16384 byte s, linear) [ 0.071609] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.071651] PCI: CLS 0 bytes, default 64 [ 0.073484] workingset: timestamp_bits=46 max_order=18 bucket_orde r=0 [ 0.074113] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.074121] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CM ODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.080431] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator [ 0.080571] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator [ 0.081426] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator [ 0.081575] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator [ 0.082679] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator [ 0.082836] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, u sing dummy regulator [ 0.082879] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not fou nd, using dummy regulator [ 0.083058] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy [ 0.083272] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator [ 0.083398] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, u sing dummy regulator [ 0.083472] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not fou nd, using dummy regulator [ 0.083643] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy [ 0.091844] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabl ed [ 0.092838] msm_serial 78b3000.serial: msm_serial: detected port # 0 [ 0.092893] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.093209] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 20, b ase_baud = 230400) is a MSM [ 0.093242] msm_serial: console setup on port #0 [ 0.093283] printk: console [ttyMSM0] enabled [ 0.901985] msm_serial: driver initialized [ 0.911165] loop: module loaded [ 0.912571] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x 61 [ 0.913121] nand: ESMT PSR1GA30DT [ 0.919788] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 20 48, OOB size: 64 [ 0.923982] spmi spmi-0: PMIC arbiter version v2 (0x20010000) [ 0.985585] i2c_dev: i2c /dev entries driver [ 0.991897] sdhci: Secure Digital Host Controller Interface driver [ 0.991943] sdhci: Copyright(c) Pierre Ossman [ 0.997045] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.003258] remoteproc remoteproc0: releasing cd00000.q6v5_wcss [ 1.010962] NET: Registered PF_INET6 protocol family [ 1.014030] Segment Routing with IPv6 [ 1.018059] In-situ OAM (IOAM) with IPv6 [ 1.021629] NET: Registered PF_PACKET protocol family [ 1.025744] 8021q: 802.1Q VLAN Support v1.8 [ 1.061403] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 1.061772] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bi n = 0 [ 1.067578] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusi ng revision = 1 [ 1.074161] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 1.081792] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 1.089325] cpr3_mem_acc_init: apc: not using memory accelerator r egulator [ 1.098458] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_co rner: fused SVS: open-loop= 704000 uV [ 1.105409] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_co rner: fused NOM: open-loop= 808000 uV [ 1.115394] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_co rner: fused TURBO: open-loop= 864000 uV [ 1.125200] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_co rner: fused STURBO: open-loop= 944000 uV [ 1.135062] cpr4_ipq807x_apss_calculate_target_quotients: apc_corn er: fused SVS: quot[ 7]= 767, quot_offset[ 7]= 0 [ 1.144822] cpr4_ipq807x_apss_calculate_target_quotients: apc_corn er: fused NOM: quot[ 7]= 972, quot_offset[ 7]= 205 [ 1.155670] cpr4_ipq807x_apss_calculate_target_quotients: apc_corn er: fused TURBO: quot[ 7]=1073, quot_offset[ 7]= 100 [ 1.166612] cpr4_ipq807x_apss_calculate_target_quotients: apc_corn er: fused STURBO: quot[ 7]=1226, quot_offset[ 7]= 150 [ 1.177779] cpr3_regulator_init_ctrl: apc: Default CPR mode = clos ed-loop [ 1.180467] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x 61 [ 1.195245] nand: ESMT PSR1GA30DT [ 1.201639] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 20 48, OOB size: 64 [ 1.205306] 17 qcomsmem partitions found on MTD device qcom_nand.0 [ 1.212325] Creating 17 MTD partitions on "qcom_nand.0": [ 1.218525] 0x000000000000-0x000000100000 : "0:sbl1" [ 1.225526] 0x000000100000-0x000000200000 : "0:mibib" [ 1.230284] 0x000000200000-0x000000280000 : "0:bootconfig" [ 1.234827] 0x000000280000-0x000000300000 : "0:bootconfig1" [ 1.240130] 0x000000300000-0x000000600000 : "0:qsee" [ 1.247900] 0x000000600000-0x000000680000 : "0:devcfg" [ 1.250843] 0x000000680000-0x000000700000 : "0:apdp" [ 1.255831] 0x000000700000-0x000000780000 : "0:rpm" [ 1.260902] 0x000000780000-0x000000800000 : "0:cdt" [ 1.265756] 0x000000800000-0x000000980000 : "0:appsblenv" [ 1.271275] 0x000000980000-0x000000b80000 : "0:appsbl" [ 1.277351] 0x000000b80000-0x000000c00000 : "0:art" [ 1.280960] 0x000000c00000-0x000003600000 : "rootfs" [ 1.322828] mtd: setting mtd12 (rootfs) as root device [ 1.323207] mtdsplit: no squashfs found in "rootfs" [ 1.326934] 0x000003600000-0x000006000000 : "rootfs_1" [ 1.370320] 0x000006000000-0x000006080000 : "0:ethphyfw" [ 1.371329] 0x000006080000-0x000006980000 : "factory_data" [ 1.383576] 0x000006980000-0x000007a80000 : "runtime_data" [ 1.407745] cpufreq: cpufreq_online: CPU0: Running at unlisted ini tial frequency: 800000 KHz, changing to: 1017600 KHz [ 1.409628] remoteproc remoteproc0: cd00000.q6v5_wcss is available [ 1.417712] ubi0: attaching mtd12 [ 1.655198] ubi0: scanning is finished [ 1.662605] ubi0: attached mtd12 (name "rootfs", size 42 MiB) [ 1.662643] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 1269 76 bytes [ 1.667350] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page si ze 2048 [ 1.674115] ubi0: VID header offset: 2048 (aligned 2048), data off set: 4096 [ 1.680965] ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 [ 1.687741] ubi0: user volume: 3, internal volumes: 1, max. volume s count: 128 [ 1.693987] ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 473343929 [ 1.701032] ubi0: available PEBs: 0, total reserved PEBs: 336, PEB s reserved for bad PEB handling: 20 [ 1.709975] ubi0: background thread "ubi_bgt0d" started, PID 602 [ 1.719923] block ubiblock0_1: created from ubi0:1(ro?[ 1.73448 5] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.735007] Freeing unused kernel memory: 1472K [ 1.740712] Run /sbin/init as init process [ 1.923590] init: Console is alive [ 1.923749] init: - watchdog - [ 2.524754] kmodloader: loading kernel modules from /etc/modules-b oot.d/* [ 2.557435] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 2.595392] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not e xist [ 4.294137] regi_init[2525]:INFO:Initializing HPPE Done!! [ 4.294267] regi_init[2574]:INFO:qca-ssdk module init succeeded! [ 4.300638] EDMA ver 1 hw init [ 4.304840] EDMA HW Reset completed succesfully [ 4.307494] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 4.311889] RxDesc:1 (15-15) RxFill:1 (7-7) [ 4.317515] GMAC5(ffffff800374d900) Invalid MAC@ - using 26:d0:89: e6:ac:eb [ 4.321270] dp5: ppe offload disabled: 0 for macid 5 [ 4.328219] dp5: Switch attached to macid 5 status: 0 [ 4.426259] Qualcomm QCA8081 90000.mdio-1:1c: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:1c, irq=POLL) [ 4.427141] GMAC6(ffffff800374b900) Invalid MAC@ - using 26:ad:0c: d7:44:f6 [ 4.435169] dp6-syn: ppe offload disabled: 0 for macid 6 [ 4.442005] dp6-syn: Switch attached to macid 6 status: 0 [ 4.524505] Qualcomm Atheros AR8031/AR8033 90000.mdio-1:04: attach ed PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL) [ 4.525319] ****************************************************** **** [ 4.534812] * NSS Data Plane driver [ 4.541115] ****************************************************** **** [ 4.562321] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.562381] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assi gned bus number 1 [ 4.566900] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci ve rsion 0x110 quirks 0x0000008002000010 [ 4.574310] xhci-hcd xhci-hcd.1.auto: irq 38, io mem 0x08a00000 [ 4.583766] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 4.589548] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assi gned bus number 2 [ 4.595104] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperS peed [ 4.603050] hub 1-0:1.0: USB hub found [ 4.609276] hub 1-0:1.0: 1 port detected [ 4.613239] usb usb2: We don't know the algorithms for LPM for thi s host, disabling LPM. [ 4.617499] hub 2-0:1.0: USB hub found [ 4.625208] hub 2-0:1.0: 1 port detected [ 4.629035] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.632775] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assi gned bus number 3 [ 4.638215] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci ve rsion 0x110 quirks 0x0000008002000010 [ 4.645670] xhci-hcd xhci-hcd.2.auto: irq 39, io mem 0x08c00000 [ 4.655093] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller [ 4.660897] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assi gned bus number 4 [ 4.666463] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperS peed [ 4.674609] hub 3-0:1.0: USB hub found [ 4.680617] hub 3-0:1.0: 1 port detected [ 4.684668] usb usb4: We don't know the algorithms for LPM for thi s host, disabling LPM. [ 4.688672] hub 4-0:1.0: USB hub found [ 4.696504] hub 4-0:1.0: 1 port detected [ 4.702753] kmodloader: done loading kernel modules from /etc/modu les-boot.d/* [ 4.705919] init: - preinit - [ 7.784080] random: crng init done /bin/board_detect: /etc/board.d/03_gpio_switches: line 5: 512: not fo und Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debu g level [ 9.959699] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 9.959840] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" start ed, PID 837 [ 9.997762] UBIFS (ubi0:2): recovery needed [ 10.095746] UBIFS (ubi0:2): recovery completed [ 10.095865] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 10.099093] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min. /max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.107013] UBIFS (ubi0:2): FS size: 22220800 bytes (21 MiB, 175 L EBs), max 185 LEBs, journal size 1142784 bytes (1 MiB, 9 LEBs) [ 10.116905] UBIFS (ubi0:2): reserved for root: 1049543 bytes (1024 KiB) [ 10.128525] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 6F2A9AA2-0601-44C9-9ABB-95CF22F596A9, small LPT model [ 10.139241] mount_root: switching to ubifs overlay [ 10.150627] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 10.156853] urandom-seed: Seeding with /etc/urandom.seed [ 10.218480] procd: - early - [ 10.218591] procd: - watchdog - Failed to connect to ubus [ 10.755603] procd: - watchdog - [ 10.755826] procd: - ubus - [ 10.810851] procd: - init - Please press Enter to activate this console. [ 11.100375] kmodloader: loading kernel modules from /etc/modules.d /* [ 11.177288] jitterentropy: Initialization failed with host not com pliant with requirements: 9 [ 11.273117] urngd: v1.0.2 started. [ 11.281802] usbcore: registered new interface driver cdc_wdm [ 11.282218] Loading modules backported from Linux version v6.9.9-0 -g28fdf4518483 [ 11.286563] Backport generated by backports.git v6.1.97-1-29-gf1d2 4a3683b2 [ 11.298563] NET: Registered PF_QIPCRTR protocol family [ 11.302890] usbcore: registered new interface driver usbserial_gen eric [ 11.305770] usbserial: USB Serial support registered for generic [ 11.313785] usbcore: registered new interface driver cdc_ether [ 11.319426] usbcore: registered new interface driver cdc_ncm [ 11.362406] PPP generic driver version 2.4.2 [ 11.363248] NET: Registered PF_PPPOX protocol family [ 11.366672] usbcore: registered new interface driver qmi_wwan [ 11.379253] ath11k c000000.wifi: ipq8074 hw2.0 [ 11.379287] ath11k c000000.wifi: FW memory mode: 0 [ 11.405431] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 11.405807] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw .mdt, size 668 [ 12.530428] remoteproc remoteproc0: remote processor cd00000.q6v5_ wcss is now up [ 12.574441] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 12.581908] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board _id 0xff soc_id 0xffffffff [ 12.581944] ath11k c000000.wifi: fw_version 0x290604a5 fw_build_ti mestamp 2023-10-12 02:06 fw_build_id WLAN.HK.2.9.0.1-01977-QCAHKSWPL_ SILICONZ-1 [ 17.955551] remoteproc remoteproc0: stopped remote processor cd000 00.q6v5_wcss [ 17.955595] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 17.961744] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw .mdt, size 668 [ 18.311610] remoteproc remoteproc0: remote processor cd00000.q6v5_ wcss is now up [ 18.312779] usbcore: registered new interface driver cdc_mbim [ 18.319761] usbcore: registered new interface driver option [ 18.323750] usbserial: USB Serial support registered for GSM modem (1-port) [ 18.330992] usbcore: registered new interface driver qcserial [ 18.336102] usbserial: USB Serial support registered for Qualcomm USB modem [ 18.356442] ath11k c000000.wifi: qmi ignore invalid mem req type 3 [ 18.360407] kmodloader: done loading kernel modules from /etc/modu les.d/* [ 18.362960] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board _id 0xff soc_id 0xffffffff [ 18.368400] ath11k c000000.wifi: fw_version 0x290604a5 fw_build_ti mestamp 2023-10-12 02:06 fw_build_id WLAN.HK.2.9.0.1-01977-QCAHKSWPL_ SILICONZ-1 [ 18.669104] ath11k c000000.wifi: htt event 48 not handled [ 21.011387] br-adults_lan: port 1(lan) entered blocking state [ 21.011432] br-adults_lan: port 1(lan) entered disabled state [ 21.016211] nss-dp 3a007000.dp6-syn lan: entered allmulticast mode [ 21.022044] nss-dp 3a007000.dp6-syn lan: entered promiscuous mode [ 21.608631] export_store: invalid GPIO 423 [ 21.653574] br-adults_lan: port 2(phy1-ap0) entered blocking state [ 21.653624] br-adults_lan: port 2(phy1-ap0) entered disabled state [ 21.658782] ath11k c000000.wifi phy1-ap0: entered allmulticast mod e [ 21.665096] ath11k c000000.wifi phy1-ap0: entered promiscuous mode [ 21.671225] br-adults_lan: port 2(phy1-ap0) entered blocking state [ 21.677300] br-adults_lan: port 2(phy1-ap0) entered forwarding sta te [ 21.947217] br-kids_lan: port 1(phy1-ap1) entered blocking state [ 21.947267] br-kids_lan: port 1(phy1-ap1) entered disabled state [ 21.952341] ath11k c000000.wifi phy1-ap1: entered allmulticast mod e [ 21.958597] ath11k c000000.wifi phy1-ap1: entered promiscuous mode [ 21.966684] br-kids_lan: port 1(phy1-ap1) entered blocking state [ 21.970538] br-kids_lan: port 1(phy1-ap1) entered forwarding state [ 22.771582] br-kids_lan: port 2(Kids_5.0g) entered blocking state [ 22.771628] br-kids_lan: port 2(Kids_5.0g) entered disabled state [ 22.776775] ath11k c000000.wifi Kids_5.0g: entered allmulticast mo de [ 22.782945] ath11k c000000.wifi Kids_5.0g: entered promiscuous mod e [ 23.302842] br-kids_lan: port 2(Kids_5.0g) entered blocking state [ 23.302891] br-kids_lan: port 2(Kids_5.0g) entered forwarding stat e [ 23.316855] br-adults_lan: port 3(Adults_5.0g) entered blocking st ate [ 23.316908] br-adults_lan: port 3(Adults_5.0g) entered disabled st ate [ 23.322389] ath11k c000000.wifi Adults_5.0g: entered allmulticast mode [ 23.328970] ath11k c000000.wifi Adults_5.0g: entered promiscuous m ode [ 23.336522] br-adults_lan: port 3(Adults_5.0g) entered blocking st ate [ 23.341657] br-adults_lan: port 3(Adults_5.0g) entered forwarding state [ 23.364258] ath11k c000000.wifi Adults_5.0g: left allmulticast mod e [ 23.364318] ath11k c000000.wifi Adults_5.0g: left promiscuous mode [ 23.369419] br-adults_lan: port 3(Adults_5.0g) entered disabled st ate [ 23.426205] br-adults_lan: port 3(Adults_5.0g) entered blocking st ate [ 23.426250] br-adults_lan: port 3(Adults_5.0g) entered disabled st ate [ 23.431665] ath11k c000000.wifi Adults_5.0g: entered allmulticast mode [ 23.438307] ath11k c000000.wifi Adults_5.0g: entered promiscuous m ode [ 23.444587] br-adults_lan: port 3(Adults_5.0g) entered blocking st ate [ 23.450991] br-adults_lan: port 3(Adults_5.0g) entered forwarding state [ 25.204492] nss-dp 3a007000.dp6-syn lan: PHY Link up speed: 1000 [ 25.204585] br-adults_lan: port 1(lan) entered blocking state [ 25.209583] br-adults_lan: port 1(lan) entered forwarding state [ 28.644487] platform phy-leds: deferred probe pending [ 31.844185] l11: disabling [ 38.774105] usb 1-1: new high-speed USB device number 2 using xhci -hcd [ 39.068217] option 1-1:1.0: GSM modem (1-port) converter detected [ 39.068522] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0 [ 39.073738] option 1-1:1.1: GSM modem (1-port) converter detected [ 39.080508] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1 [ 39.086559] option 1-1:1.2: GSM modem (1-port) converter detected [ 39.093315] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 [ 39.099454] option 1-1:1.3: GSM modem (1-port) converter detected [ 39.106172] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3 BusyBox v1.36.1 (2024-08-08 21:48:47 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r27126-38a87b1b8d ----------------------------------------------------- root@OpenWrt:/#


cat /proc/devices Character devices: 1 mem 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 13 input 29 fb 89 i2c 90 mtd 116 alsa 128 ptm 136 pts 153 spi 180 usb 189 usb_device 239 flash_chrdev 241 ubi0 242 subsys 243 nvme 244 ttyMSM 245 ttyMSM 246 dcc_sram 247 mhi_uci 248 watchdog 249 iio 250 ptp 251 pps 252 rtc 253 msm_sps 254 rpmsg Block devices: 1 ramdisk 259 blkext 31 mtdblock 179 mmc 253 ubiblock 254 nvme root@(none):/#


/dts-v1/; /* * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ #include "qcom-ipq807x-soc.dtsi" #include "qcom-ipq807x-hk-cpu.dtsi" #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> / { #address-cells = <0x2>; #size-cells = <0x2>; model = "Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C5"; compatible = "qcom,ipq807x-hk01", "qcom,ipq807x"; qcom,msm-id = <0x143 0x0>, <0x158 0x0>, <0x186 0x0>, <0x188 0x0>; interrupt-parent = <&intc>; qcom,board-id = <0x8 0x0>; qcom,pmic-id = <0x0 0x0 0x0 0x0>; aliases { sdhc1 = &sdhc_1; /* SDC1 eMMC slot */ /* * Aliases as required by u-boot * to patch MAC addresses */ ethernet0 = "/soc/dp1"; ethernet1 = "/soc/dp2"; ethernet2 = "/soc/dp3"; ethernet3 = "/soc/dp4"; ethernet4 = "/soc/dp5"; ethernet5 = "/soc/dp6"; }; chosen { bootargs = "console=ttyMSM0,115200,n8 root=/dev/ram0 rw init=/init"; bootargs-append = " swiotlb=1"; }; }; &spmi_bus { pmic@0 { compatible ="qcom,spmi-pmic"; reg = <0x0 SPMI_USID>; #address-cells = <1>; #size-cells = <0>; pmm8074_gpios: gpios@c000 { compatible = "qcom,pma8084-gpio"; reg = <0xc000 0xc00>; gpio-controller; #gpio-cells = <2>; interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, <0 0xc1 0 IRQ_TYPE_NONE>, <0 0xc2 0 IRQ_TYPE_NONE>, <0 0xc3 0 IRQ_TYPE_NONE>, <0 0xc4 0 IRQ_TYPE_NONE>, <0 0xc5 0 IRQ_TYPE_NONE>, <0 0xc6 0 IRQ_TYPE_NONE>, <0 0xc7 0 IRQ_TYPE_NONE>, <0 0xc8 0 IRQ_TYPE_NONE>, <0 0xc9 0 IRQ_TYPE_NONE>, <0 0xca 0 IRQ_TYPE_NONE>, <0 0xcb 0 IRQ_TYPE_NONE>; pinctrl-0 = <&pmm8074_gpio>; pinctrl-names = "default"; pmm8074_gpio: pmm8074_gpio { pinconf { pins = "gpio6"; function = PMIC_GPIO_FUNC_NORMAL; bias-pull-up; output-high; }; }; }; }; }; &tlmm { pinctrl-0 = <&pcie_sdx_gpio>; pinctrl-names = "default"; pcie_sdx_gpio: pcie_sdx_gpio { ap2mdm_err_ftl { pins = "gpio27"; function = "gpio"; drive-strength = <8>; bias-pull-down; }; sdx_pon_gpio { pins = "gpio30"; function = "gpio"; drive-strength = <8>; bias-pull-up; output-high; }; ap2mdm_status { pins = "gpio26"; function = "gpio"; drive-strength = <8>; bias-pull-up; output-high; }; }; pcie_wake_pins: pcie0_wake_gpio { pins = "gpio59"; function = "pcie0_wake"; drive-strength = <8>; bias-pull-up; }; mdio_pins: mdio_pinmux { mux_0 { pins = "gpio68"; function = "mdc"; drive-strength = <8>; bias-pull-up; }; mux_1 { pins = "gpio69"; function = "mdio"; drive-strength = <8>; bias-pull-up; }; mux_2 { pins = "gpio37"; function = "gpio"; bias-pull-up; }; mux_3 { pins = "gpio44"; function = "gpio"; bias-pull-up; }; }; uart_pins: uart_pins { mux { pins = "gpio23", "gpio24"; function = "blsp4_uart1"; drive-strength = <8>; bias-disable; }; }; qpic_pins: qpic_pins { data_0 { pins = "gpio15"; function = "qpic_pad0"; drive-strength = <8>; bias-disable; }; data_1 { pins = "gpio12"; function = "qpic_pad1"; drive-strength = <8>; bias-disable; }; data_2 { pins = "gpio13"; function = "qpic_pad2"; drive-strength = <8>; bias-disable; }; data_3 { pins = "gpio14"; function = "qpic_pad3"; drive-strength = <8>; bias-disable; }; data_4 { pins = "gpio5"; function = "qpic_pad4"; drive-strength = <8>; bias-disable; }; data_5 { pins = "gpio6"; function = "qpic_pad5"; drive-strength = <8>; bias-disable; }; data_6 { pins = "gpio7"; function = "qpic_pad6"; drive-strength = <8>; bias-disable; }; data_7 { pins = "gpio8"; function = "qpic_pad7"; drive-strength = <8>; bias-disable; }; data_8 { pins = "gpio16"; function = "qpic_pad8"; drive-strength = <8>; bias-disable; }; qpic_pad { pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4", "gpio9", "gpio10", "gpio11", "gpio17"; function = "qpic_pad"; drive-strength = <8>; bias-disable; }; }; hsuart_pins: hsuart_pins { mux { pins = "gpio46", "gpio47", "gpio48", "gpio49"; function = "blsp2_uart"; drive-strength = <8>; bias-disable; }; }; fan_pins: fan_pins { mux { pins = "gpio40", "gpio41", "gpio42"; function = "gpio"; drive-strength = <2>; bias-disable; }; }; antenna_pins: antenna_pins { ext_antenna_en { pins = "gpio56"; function = "gpio"; drive-strength = <2>; bias-disable; }; }; modem_pins: modem_pins { modem_reset { pins = "gpio29"; function = "gpio"; drive-strength = <2>; bias-disable; }; w_disable { pins = "gpio55"; function = "gpio"; drive-strength = <2>; bias-disable; }; }; ledc_pins: ledc_pinmux { led_clk { pins = "gpio18"; function = "led0"; drive-strength = <8>; bias-pull-down; }; led_data { pins = "gpio19"; function = "led1"; drive-strength = <8>; bias-pull-down; }; led_clr { pins = "gpio20"; function = "led2"; drive-strength = <8>; bias-pull-up; }; }; }; &soc { mdio: mdio@90000 { pinctrl-0 = <&mdio_pins>; pinctrl-names = "default"; phy-reset-gpio = <&tlmm 44 0 &tlmm 37 1>; compatible = "qcom,ipq40xx-mdio", "qcom,qca-mdio"; phy0: ethernet-phy@0 { reg = <0>; }; phy1: ethernet-phy@1 { reg = <1>; }; phy2: ethernet-phy@2 { reg = <2>; }; phy3: ethernet-phy@3 { reg = <3>; }; phy4: ethernet-phy@4 { reg = <28>; }; phy5: ethernet-phy@5 { reg = <4>; }; }; ess-switch@3a000000 { switch_cpu_bmp = <0x1>; /* cpu port bitmap */ switch_lan_bmp = <0x3e>; /* lan port bitmap */ switch_wan_bmp = <0x40>; /* wan port bitmap */ switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/ switch_mac_mode1 = <0xf>; /* mac mode for uniphy instance1*/ switch_mac_mode2 = <0xf>; /* mac mode for uniphy instance2*/ bm_tick_mode = <0>; /* bm tick mode */ tm_tick_mode = <0>; /* tm tick mode */ qcom,port_phyinfo { port@0 { port_id = <1>; phy_address = <0>; }; port@1 { port_id = <2>; phy_address = <1>; }; port@2 { port_id = <3>; phy_address = <2>; }; port@3 { port_id = <4>; phy_address = <3>; }; port@4 { port_id = <5>; phy_address = <28>; port_mac_sel="QGMAC_PORT"; }; port@5 { port_id = <6>; phy_address = <4>; }; }; port_scheduler_resource { port@0 { port_id = <0>; ucast_queue = <0 143>; mcast_queue = <256 271>; l0sp = <0 35>; l0cdrr = <0 47>; l0edrr = <0 47>; l1cdrr = <0 7>; l1edrr = <0 7>; }; port@1 { port_id = <1>; ucast_queue = <144 159>; mcast_queue = <272 275>; l0sp = <36 39>; l0cdrr = <48 63>; l0edrr = <48 63>; l1cdrr = <8 11>; l1edrr = <8 11>; }; port@2 { port_id = <2>; ucast_queue = <160 175>; mcast_queue = <276 279>; l0sp = <40 43>; l0cdrr = <64 79>; l0edrr = <64 79>; l1cdrr = <12 15>; l1edrr = <12 15>; }; port@3 { port_id = <3>; ucast_queue = <176 191>; mcast_queue = <280 283>; l0sp = <44 47>; l0cdrr = <80 95>; l0edrr = <80 95>; l1cdrr = <16 19>; l1edrr = <16 19>; }; port@4 { port_id = <4>; ucast_queue = <192 207>; mcast_queue = <284 287>; l0sp = <48 51>; l0cdrr = <96 111>; l0edrr = <96 111>; l1cdrr = <20 23>; l1edrr = <20 23>; }; port@5 { port_id = <5>; ucast_queue = <208 223>; mcast_queue = <288 291>; l0sp = <52 55>; l0cdrr = <112 127>; l0edrr = <112 127>; l1cdrr = <24 27>; l1edrr = <24 27>; }; port@6 { port_id = <6>; ucast_queue = <224 239>; mcast_queue = <292 295>; l0sp = <56 59>; l0cdrr = <128 143>; l0edrr = <128 143>; l1cdrr = <28 31>; l1edrr = <28 31>; }; port@7 { port_id = <7>; ucast_queue = <240 255>; mcast_queue = <296 299>; l0sp = <60 63>; l0cdrr = <144 159>; l0edrr = <144 159>; l1cdrr = <32 35>; l1edrr = <32 35>; }; }; port_scheduler_config { port@0 { port_id = <0>; l1scheduler { group@0 { sp = <0 1>; /*L0 SPs*/ /*cpri cdrr epri edrr*/ cfg = <0 0 0 0>; }; }; l0scheduler { group@0 { /*unicast queues*/ ucast_queue = <0 4 8>; /*multicast queues*/ mcast_queue = <256 260>; /*sp cpri cdrr epri edrr*/ cfg = <0 0 0 0 0>; }; group@1 { ucast_queue = <1 5 9>; mcast_queue = <257 261>; cfg = <0 1 1 1 1>; }; group@2 { ucast_queue = <2 6 10>; mcast_queue = <258 262>; cfg = <0 2 2 2 2>; }; group@3 { ucast_queue = <3 7 11>; mcast_queue = <259 263>; cfg = <0 3 3 3 3>; }; }; }; port@1 { port_id = <1>; l1scheduler { group@0 { sp = <36>; cfg = <0 8 0 8>; }; group@1 { sp = <37>; cfg = <1 9 1 9>; }; }; l0scheduler { group@0 { ucast_queue = <144>; ucast_loop_pri = <16>; mcast_queue = <272>; mcast_loop_pri = <4>; cfg = <36 0 48 0 48>; }; }; }; port@2 { port_id = <2>; l1scheduler { group@0 { sp = <40>; cfg = <0 12 0 12>; }; group@1 { sp = <41>; cfg = <1 13 1 13>; }; }; l0scheduler { group@0 { ucast_queue = <160>; ucast_loop_pri = <16>; mcast_queue = <276>; mcast_loop_pri = <4>; cfg = <40 0 64 0 64>; }; }; }; port@3 { port_id = <3>; l1scheduler { group@0 { sp = <44>; cfg = <0 16 0 16>; }; group@1 { sp = <45>; cfg = <1 17 1 17>; }; }; l0scheduler { group@0 { ucast_queue = <176>; ucast_loop_pri = <16>; mcast_queue = <280>; mcast_loop_pri = <4>; cfg = <44 0 80 0 80>; }; }; }; port@4 { port_id = <4>; l1scheduler { group@0 { sp = <48>; cfg = <0 20 0 20>; }; group@1 { sp = <49>; cfg = <1 21 1 21>; }; }; l0scheduler { group@0 { ucast_queue = <192>; ucast_loop_pri = <16>; mcast_queue = <284>; mcast_loop_pri = <4>; cfg = <48 0 96 0 96>; }; }; }; port@5 { port_id = <5>; l1scheduler { group@0 { sp = <52>; cfg = <0 24 0 24>; }; group@1 { sp = <53>; cfg = <1 25 1 25>; }; }; l0scheduler { group@0 { ucast_queue = <208>; ucast_loop_pri = <16>; mcast_queue = <288>; mcast_loop_pri = <4>; cfg = <52 0 112 0 112>; }; }; }; port@6 { port_id = <6>; l1scheduler { group@0 { sp = <56>; cfg = <0 28 0 28>; }; group@1 { sp = <57>; cfg = <1 29 1 29>; }; }; l0scheduler { group@0 { ucast_queue = <224>; ucast_loop_pri = <16>; mcast_queue = <292>; mcast_loop_pri = <4>; cfg = <56 0 128 0 128>; }; }; }; port@7 { port_id = <7>; l1scheduler { group@0 { sp = <60>; cfg = <0 32 0 32>; }; group@1 { sp = <61>; cfg = <1 33 1 33>; }; }; l0scheduler { group@0 { ucast_queue = <240>; ucast_loop_pri = <16>; mcast_queue = <296>; cfg = <60 0 144 0 144>; }; }; }; }; }; dp1 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <1>; reg = <0x3a001000 0x200>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <0>; phy-mode = "sgmii"; }; dp2 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <2>; reg = <0x3a001200 0x200>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <1>; phy-mode = "sgmii"; }; dp3 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <3>; reg = <0x3a001400 0x200>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <2>; phy-mode = "sgmii"; }; dp4 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <4>; reg = <0x3a001600 0x200>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <3>; phy-mode = "sgmii"; }; dp5 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <5>; reg = <0x3a001800 0x200>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <28>; phy-mode = "sgmii"; }; dp6 { device_type = "network"; compatible = "qcom,nss-dp"; qcom,id = <6>; reg = <0x3a007000 0x3fff>; qcom,mactype = <0>; local-mac-address = [000000000000]; qcom,link-poll = <1>; qcom,phy-mdio-addr = <4>; phy-mode = "sgmii"; }; gpio_keys { compatible = "gpio-keys"; button@1 { label = "reset"; linux,code = <KEY_RESTART>; gpios = <&tlmm 27 GPIO_ACTIVE_LOW>; linux,input-type = <1>; }; }; fans { compatible = "gpio-fan"; pinctrl-0 = <&fan_pins>; pinctrl-names = "default"; fan1 { label = "fan1"; gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; }; fan2 { label = "fan2"; gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>; }; fan3 { label = "fan3"; gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; }; }; antennas { compatible = "gpio-antenna"; pinctrl-0 = <&antenna_pins>; pinctrl-names = "default"; ext_antenna_en { label = "ext_antenna_en"; gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>; }; }; modem { compatible = "gpio-modem"; pinctrl-0 = <&modem_pins>; pinctrl-names = "default"; modem_reset { label = "modem_reset"; gpios = <&tlmm 29 GPIO_ACTIVE_LOW>; }; w_disable { label = "w_disable"; gpios = <&tlmm 55 GPIO_ACTIVE_LOW>; }; }; leds { compatible = "gpio-leds"; red { gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; default-state = "on"; }; green { gpios = <&tlmm 50 GPIO_ACTIVE_HIGH>; default-state = "on"; }; blue { gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>; default-state = "off"; }; yellow_mix { default-state = "off"; virtuals = <0>, <1>, <3>; }; blue_mix { default-state = "off"; virtuals = <1>, <2>, <3>; }; }; }; &serial_blsp4 { pinctrl-0 = <&uart_pins>; pinctrl-names = "default"; status = "ok"; }; &serial_blsp2 { pinctrl-0 = <&hsuart_pins>; pinctrl-names = "default"; status = "ok"; }; &msm_imem { status = "enabled"; }; &ssphy_0 { status = "ok"; }; &qusb_phy_0 { status = "ok"; }; &ssphy_1 { status = "ok"; }; &qusb_phy_1 { status = "ok"; }; &usb3_0 { status = "ok"; }; &usb3_1 { status = "ok"; }; &cryptobam { status = "ok"; }; &crypto { status = "ok"; }; &sdhc_1 { qcom,clk-rates = <400000 25000000 50000000 100000000 \ 192000000 384000000>; qcom,bus-speed-mode = "HS400_1p8v", "HS200_1p8v", "DDR_1p8v"; qcom,nonremovable; status = "ok"; }; &qpic_bam { status = "ok"; }; &nand { pinctrl-0 = <&qpic_pins>; pinctrl-names = "default"; status = "ok"; }; &pcie0 { interrupts-extended = <&intc 0 52 0>, <&intc 0 416 0>, <&intc 0 417 0>, <&intc 0 418 0>, <&intc 0 419 0>, <&intc 0 420 0>, <&intc 0 421 0>, <&intc 0 422 0>, <&intc 0 423 0>, <&intc 0 424 0>, <&intc 0 425 0>, <&intc 0 426 0>, <&intc 0 427 0>, <&intc 0 428 0>, <&intc 0 429 0>, <&intc 0 430 0>, <&intc 0 431 0>, <&tlmm 59 0>, <&tlmm 33 0>; interrupt-names = "msi", "msi_0", "msi_1", "msi_2", "msi_3", "msi_4", "msi_5", "msi_6", "msi_7", "msi_8", "msi_9", "msi_10", "msi_11", "msi_12", "msi_13", "msi_14", "msi_15", "wake_gpio"; pinctrl-0 = <&pcie_wake_pins>; pinctrl-names = "default"; link_retries_count = <10>; use_delay = <0>; }; &pcie1 { status = "disabled"; }; &qpic_lcd { status = "ok"; }; &qpic_lcd_panel { status = "ok"; }; &ledc { pinctrl-0 = <&ledc_pins>; pinctrl-names = "default"; status = "ok"; led0 { label = "ipq::led0"; linux,default-trigger = "led_wifi_son_green"; }; led1 { label = "ipq::led1"; linux,default-trigger = "led_wifi_son_orange"; }; led2 { label = "ipq::led2"; linux,default-trigger = "led_wifi_son_blue"; }; led3 { label = "ipq::led3"; linux,default-trigger = "led_2g"; }; led4 { label = "ipq::led4"; linux,default-trigger = "led_5gl"; }; led5 { label = "ipq::led5"; linux,default-trigger = "led_5gh"; }; led6 { label = "ipq::led6"; linux,default-trigger = "led_lan"; }; led7 { label = "ipq::led7"; linux,default-trigger = "led_wan"; }; led8 { label = "ipq::led8"; linux,default-trigger = "led_10g_link"; }; led9 { label = "ipq::led9"; linux,default-trigger = "led_sfp"; }; led10 { label = "ipq::led10"; linux,default-trigger = "led_bt"; }; led11 { label = "ipq::led11"; linux,default-trigger = "none"; }; led12 { label = "ipq::led12"; linux,default-trigger = "none"; }; }; &watchdog { mhi-wdt-panic-enable; }; &pcie0_rp { #address-cells = <5>; #size-cells = <0>; status = "ok"; aliases { mhi-netdev0 = &mhi_netdev_0; mhi_netdev2 = &mhi_netdev_2; }; mhi_0: qcom,mhi@0 { reg = <0 0 0 0 0 >; ap2mdm = <26>; mdm2ap = <25>; /* controller specific configuration */ qcom,iommu-dma = "disabled"; /* mhi bus specific settings */ mhi,max-channels = <110>; mhi,timeout = <60000>; mhi,ssr-negotiate; mhi_channels: mhi_channels { #address-cells = <1>; #size-cells = <0>; mhi_chan@0 { reg = <0>; label = "LOOPBACK"; mhi,num-elements = <64>; mhi,event-ring = <2>; mhi,chan-dir = <1>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@1 { reg = <1>; label = "LOOPBACK"; mhi,num-elements = <64>; mhi,event-ring = <2>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@4 { reg = <4>; label = "DIAG"; mhi,num-elements = <64>; mhi,event-ring = <1>; mhi,chan-dir = <1>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@5 { reg = <5>; label = "DIAG"; mhi,num-elements = <64>; mhi,event-ring = <3>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@14 { reg = <14>; label = "QMI0"; mhi,num-elements = <64>; mhi,event-ring = <1>; mhi,chan-dir = <1>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@15 { reg = <15>; label = "QMI0"; mhi,num-elements = <64>; mhi,event-ring = <2>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@16 { reg = <16>; label = "QMI1"; mhi,num-elements = <64>; mhi,event-ring = <3>; mhi,chan-dir = <1>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@17 { reg = <17>; label = "QMI1"; mhi,num-elements = <64>; mhi,event-ring = <3>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@18 { reg = <18>; label = "IP_CTRL"; mhi,num-elements = <64>; mhi,event-ring = <1>; mhi,chan-dir = <1>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@19 { reg = <19>; label = "IP_CTRL"; mhi,num-elements = <64>; mhi,event-ring = <1>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; mhi,auto-queue; }; mhi_chan@20 { reg = <20>; label = "IPCR"; mhi,num-elements = <64>; mhi,event-ring = <2>; mhi,chan-dir = <1>; mhi,data-type = <1>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; mhi,auto-start; }; mhi_chan@21 { reg = <21>; label = "IPCR"; mhi,num-elements = <64>; mhi,event-ring = <2>; mhi,chan-dir = <2>; mhi,data-type = <0>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; mhi,auto-queue; mhi,auto-start; }; mhi_chan@46 { reg = <46>; label = "IP_SW0"; mhi,num-elements = <512>; mhi,event-ring = <4>; mhi,chan-dir = <1>; mhi,data-type = <1>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@47 { reg = <47>; label = "IP_SW0"; mhi,num-elements = <512>; mhi,event-ring = <5>; mhi,chan-dir = <2>; mhi,data-type = <4>; mhi,doorbell-mode = <2>; mhi,ee = <0x4>; }; mhi_chan@100 { reg = <100>; label = "IP_HW0"; mhi,num-elements = <512>; mhi,event-ring = <6>; mhi,chan-dir = <1>; mhi,data-type = <1>; mhi,doorbell-mode = <3>; mhi,ee = <0x4>; mhi,db-mode-switch; }; mhi_chan@101 { reg = <101>; label = "IP_HW0"; mhi,num-elements = <512>; mhi,event-ring = <7>; mhi,chan-dir = <2>; mhi,data-type = <4>; mhi,doorbell-mode = <3>; mhi,ee = <0x4>; }; mhi_chan@102 { reg = <102>; label = "IP_HW_ADPL"; mhi,event-ring = <8>; mhi,chan-dir = <2>; mhi,data-type = <3>; mhi,ee = <0x4>; mhi,offload-chan; mhi,lpm-notify; }; }; mhi_events: mhi_events { #address-cells = <1>; #size-cells = <0>; mhi_event@0 { reg = <0>; mhi,num-elements = <32>; mhi,intmod = <1>; mhi,msi = <1>; mhi,priority = <1>; mhi,brstmode = <2>; mhi,data-type = <1>; }; mhi_event@1 { mhi,num-elements = <256>; mhi,intmod = <1>; mhi,msi = <2>; mhi,priority = <1>; mhi,brstmode = <2>; }; mhi_event@2 { mhi,num-elements = <256>; mhi,intmod = <1>; mhi,msi = <3>; mhi,priority = <1>; mhi,brstmode = <2>; }; mhi_event@3 { mhi,num-elements = <256>; mhi,intmod = <1>; mhi,msi = <4>; mhi,priority = <1>; mhi,brstmode = <2>; }; mhi_event@4 { mhi,num-elements = <1024>; mhi,intmod = <5>; mhi,msi = <5>; mhi,chan = <46>; mhi,priority = <1>; mhi,brstmode = <2>; }; mhi_event@5 { mhi,num-elements = <1024>; mhi,intmod = <5>; mhi,msi = <6>; mhi,chan = <47>; mhi,priority = <1>; mhi,brstmode = <2>; mhi,client-manage; }; mhi_event@6 { mhi,num-elements = <1024>; mhi,intmod = <5>; mhi,msi = <5>; mhi,chan = <100>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; }; mhi_event@7 { mhi,num-elements = <1024>; mhi,intmod = <5>; mhi,msi = <6>; mhi,chan = <101>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,client-manage; mhi,hw-ev; }; mhi_event@8 { mhi,num-elements = <0>; mhi,intmod = <0>; mhi,msi = <0>; mhi,chan = <102>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; mhi,client-manage; mhi,offload; }; mhi_event@9 { mhi,num-elements = <1024>; mhi,intmod = <5>; mhi,msi = <7>; mhi,chan = <103>; mhi,priority = <1>; mhi,brstmode = <2>; mhi,hw-ev; }; mhi_event@10 { mhi,num-elements = <0>; mhi,intmod = <0>; mhi,msi = <0>; mhi,chan = <105>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; mhi,client-manage; mhi,offload; }; mhi_event@11 { mhi,num-elements = <0>; mhi,intmod = <0>; mhi,msi = <0>; mhi,chan = <106>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; mhi,client-manage; mhi,offload; }; mhi_event@12 { mhi,num-elements = <0>; mhi,intmod = <0>; mhi,msi = <0>; mhi,chan = <107>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; mhi,client-manage; mhi,offload; }; mhi_event@13 { mhi,num-elements = <0>; mhi,intmod = <0>; mhi,msi = <0>; mhi,chan = <108>; mhi,priority = <1>; mhi,brstmode = <3>; mhi,hw-ev; mhi,client-manage; mhi,offload; }; }; mhi_devices: mhi_devices { #address-cells = <1>; #size-cells = <0>; mhi_netdev_0: mhi_rmnet@0 { reg = <0x0>; mhi,chan = "IP_HW0"; mhi,interface-name = "rmnet_mhi"; mhi,mru = <0x4000>; mhi,chain-skb; }; mhi_rmnet@1 { reg = <0x1>; mhi,chan = "IP_HW0_RSC"; mhi,mru = <0x8000>; mhi,rsc-parent = <&mhi_netdev_0>; }; mhi_netdev_2: mhi_rmnet@2 { reg = <0x2>; mhi,chan = "IP_SW0"; mhi,interface-name = "rmnet_mhi_sw"; mhi,mru = <0x4000>; mhi,disable-chain-skb; }; mhi_qrtr { mhi,chan = "IPCR"; qcom,net-id = <3>; }; }; }; };


There is potential to exploit the HTTP U-Boot recovery method or local software update with a buffer overflow to run arbitrary shellcode: https://github.com/naf419/tplink_deco_exploits

The unit has 2x OS images on NAND flash, one image is for normal operation and the other one is for recovering of firmware or upgrading, the system has two root partitions and it switches between each upgrade (currently not implemented in OpenWrt).

The base MAC address is stored in the factory_data partition and contains a single MAC address used to derive all others, it also contains the cloud key and IMEI number for the modem and other manufacturer ID's.

The fan has three individual bits controlling a bitwise binary speed select from stop to 6krpm.

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/08/22 20:23
  • by professor_jonny