TP-Link Archer AX50
A 802.11ax Wi-Fi 6 device with Intel (Lantiq) chip.
OpenWrt support
Not supported.
See:
Hardware highlights
| CPU | Ram | Flash | Network | WLAN 2.4Ghz | WLAN 5Ghz | USB | Serial | JTag |
|---|---|---|---|---|---|---|---|---|
| Intel AnyWAN SoC GRX350 @ 800 MHz | 256 MiB | 128 MiB | 5x Gigabit | b/g/n/ax | a/n/ac/ax | 1x 3.0 | Yes | No |
Buttons
→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.
The AX50 has the following buttons on the rear:
| BUTTON | Event |
|---|---|
| WPS | wps |
| Reset | reset |
| LED | Turns on/off front LEDs |
Hardware
Info
| Architecture | Mips |
|---|---|
| Vendor | Intel |
| Bootloader | U-Boot 2010.06-LANTIQ-v-2.3.149 |
| System-On-Chip | Intel GRX500 rev 1.2 |
| CPU/Speed | GRX350A3 600/800 MHz |
| Flash-Chip | Gigadevice PSU1GA30DT |
| Flash size | 128 MiB |
| RAM-Chip | ? |
| RAM | 256 MiB |
| Wireless | Intel (Lantiq) WAV654 |
| Ethernet | 10/100/1000 Mbit/s w/ vlan support |
| Switch | Intel (Lantiq) GRX500 |
| USB | 1x 3.0 |
| Serial | Yes |
| JTAG | No |
Flash Layout
Flash layout in OEM FW:
[ 3.140000] Creating 7 MTD partitions on "17c00000.nand-parts": [ 3.150000] 0x000000000000-0x000000100000 : "uboot" [ 3.160000] 0x000000100000-0x000000140000 : "ubootconfigA" [ 3.160000] 0x000000140000-0x000000180000 : "ubootconfigB" [ 3.170000] 0x000000180000-0x0000001c0000 : "gphyfirmware" [ 3.170000] 0x0000001c0000-0x0000002c0000 : "calibration" [ 3.180000] 0x0000002c0000-0x000007ec0000 : "system_sw" [ 3.180000] 0x000007ec0000-0x000008000000 : "res"
Photos
Insert photo of front of the casing
Insert photo of back of the casing
Insert photo of backside label
Insert photo of PCB
Opening the case
Plastic top cover can be pryed open with use of spudger. Plastic is brittle, so expect some clips to break. There are two clips at the rear, two on either side, and four at the front.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Open case, solder 4 pin 0.1“ pitch SIP to front right hand side of PCB.
Pins from left to right are:
- TX from board
- RX to board
- GND
- VCC (3.3V)
| Serial connection parameters | 115200, 8N1 |
|---|
JTAG
Not supported.
Bootlogs
OEM bootlog
ROM VER: 2.1.0 CFG 0a B . . U-Boot 2010.06-dirty-LANTIQ-v-2.3.149 (Jul 08 2020 - 12:59:31) interAptiv cps cpu/ddr run in 800/666 Mhz DRAM: 224 MiB NAND: ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Gigadevice PSU1GA30DT) 128 MiB Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 In: serial Out: serial Err: serial Net: multi type Internal phy firmware version: 0x8548 GRX500 Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 0 Creating 1 MTD partitions on "nand0": 0x0000002c0000-0x000007ec0000 : "mtd=5" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=5" UBI: MTD device size: 124 MiB UBI: number of good PEBs: 992 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 5 UBI: available PEBs: 349 UBI: total number of reserved PEBs: 643 UBI: number of PEBs reserved for bad PEB handling: 9 UBI: max/mean erase counter: 2/0 bootcoreA volume not found Volume kernelA found at volume id 0 read 0 bytes from volume 0 to 80800000(buf address) Read [3145728] bytes ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-3.10.104 Created: 2020-07-08 5:17:29 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3145664 Bytes = 3 MiB Load Address: a0020000 Entry Point: a002df00 Verifying Checksum ... OK Uncompressing Kernel Image ... OK
OpenWrt bootlog
Starting kernel ... [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.10.104 (raymond@Raymond) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 15.05_ltq) ) #1 SMP Wed Jul 8 13:17:08 CST 2020 [ 0.000000] TLBINV/F supported, config4=0xc0000000 [ 0.000000] TLBINV/F supported, config4=0xc0000000 [ 0.000000] SoC: GRX500 rev 1.2 [ 0.000000] GCMP present [ 0.000000] L2-only SYNC available [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv) [ 0.000000] Enhanced Virtual Addressing (EVA 1GB) activated [ 0.000000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000 [ 0.000000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001 [ 0.000000] BEV Overlay segment = 0xb0000000, size = 0x10000000 [ 0.000000] segctr0 2d0a0a segctr1 40d020a segctr2 38004d [ 0.000000] MIPS: machine is EASY350 ANYWAN (GRX350) Router model [ 0.000000] CMP IOCU detected [ 0.000000] Hardware DMA cache coherency disabled [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 1e000000 @ 20000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 10000000 @ 20000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] reserving 18874368 bytes @ 6800a980 for CBM [ 0.000000] reserving 8388608 bytes @ 6920a980 for CBM [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x20000000-0x27ffffff] [ 0.000000] Normal [mem 0x28000000-0x2fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x20000000-0x2fffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @69c0e000 s7936 r8192 d12544 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: ubi.mtd=system_sw rootfsname=rootfsA ro rootfstype=squashfs do_overlay console=ttyLTQ0,115200 ethaddr=00:E0:92:00:01:40 panic=1 mtdparts=17c00000.nand-parts:1m(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),1m(calibration),124m(system_sw),-(res) init=/etc/preinit active_bank=A update_chk=0 maxcpus=4 pci=pcie_bus_perf ethwan= ubootver=U-Boot-2010.06-dirty-LANTIQ-v-2.3.149 mem=256M@512M Production= [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 222004k/262144k available (6777k kernel code, 40140k reserved, 1947k data, 296k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:527 [ 0.000000] GIC: present [ 0.000000] EIC: off [ 0.000000] GIC map size 263 [ 0.000000] gic: revision 3.0 [ 0.000000] CPU0: c0 status register 1100fc00 [ 0.000000] of_gic_init init done [ 0.000000] CPU Clock: 800000000Hz mips_hpt_frequency 400000000Hz [ 0.000000] CBM Clock: 600000000Hz DDR Clock: 666666666Hz NGI Clock: 300000000Hz [ 0.000000] clock event init done ! [ 0.000000] gptu_setup_clocksource: done ! [ 0.000000] Calibrating delay loop... 513.63 BogoMIPS (lpj=2568192) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] Initializing cgroup subsys memory [ 0.090000] size of core = 336, MAXCORE = 2 , MAXCPU = 4, MAXTCS = 6 MAX_VPE = 2 [ 0.090000] [update_DB_from_DT]:[363], cpuid = 0 name = LINUX [ 0.100000] [update_DB_from_DT]:[363], cpuid = 1 name = LINUX [ 0.100000] [update_DB_from_DT]:[363], cpuid = 2 name = LINUX [ 0.110000] [update_DB_from_DT]:[363], cpuid = 3 name = MPEFW [ 0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 1 [ 0.120000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 2 [ 0.120000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 3 [ 0.130000] [ 0.130000] Initial ITC_Address_Map0 00000000 [ 0.130000] def ITC_Address_Map1 01200000 new ITC_Address_Map1 0120fc00 def ITC_Address_Map0 00000000 new ITC_Address_Map0 1c300001 ITC Init done on Core 0 on CPU 0 !!! [ 0.150000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11 [ 0.150000] [vmb_cpu_start]:[849] vmb_fw_msg_t = a00000b8 cpu = 1 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!! [gic_trigger]:[551] VMB_CPU_IPI1 - 20 CPU = 1 Outside WAIT got IPI interrupt to launch from cpu 01 MSG_ID = 01[ 0.160000] [vmb_cpu_start]:[892] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!! [ 0.160000] TLBINV/F supported, config4=0xc0000000 [ 0.160000] TLBINV/F supported, config4=0xc0000000 [ 0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.160000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000 [ 0.160000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001 [ 0.160000] BEV Overlay segment = 0xb0000000, size = 0x10000000 [ 0.160000] [ 0.160000] Initial ITC_Address_Map0 1c300001 [ 0.160000] ITC Memory is already initialised for Core 0 at address 1c300000 !!![ 0.160000] CPU1 revision is: 0001a120 (MIPS interAptiv) [ 0.220000] [vmb_cpu_active]:[268] action = 10 , cpu = 1 [ 0.220000] [vmb_cpu_start]:[908] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 1 ret1 = 9995 vpet = 608f7854, smp_processor_id() = 0 , vpet->fw_vmb =608f7880 !!!! [ 0.220000] [vmb_cpu_start]:[915] ret = 1 [ 0.230000] Synchronize counters for CPU 1: done. [ 0.230000] GPTC clock event init on cpu: 1 [ 0.230000] clock event init done ! [ 0.240000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11 [ 0.240000] [vmb_cpu_start]:[849] vmb_fw_msg_t = a0000168 cpu = 2 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!! [gic_trigger]:[555] VMB_CPU_IPI2 - 21 CPU = 2 Outside WAIT got IPI interrupt to launch from cpu 02 MSG_ID = 01[ 0.250000] [vmb_cpu_start]:[892] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!! [ 0.250000] TLBINV/F supported, config4=0xc0000000 [ 0.250000] TLBINV/F supported, config4=0xc0000000 [ 0.250000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.250000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.250000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.250000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000 [ 0.250000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001 [ 0.250000] BEV Overlay segment = 0xb0000000, size = 0x10000000 [ 0.250000] [ 0.250000] Initial ITC_Address_Map0 00000000 [ 0.250000] [ 0.250000] def ITC_Address_Map1 01200000 [ 0.250000] new ITC_Address_Map1 0120fc00 [ 0.250000] def ITC_Address_Map0 00000000 [ 0.250000] new ITC_Address_Map0 1c300001 [ 0.250000] ITC Init done on Core 1 on CPU 2 !!! [ 0.250000] CPU2 revision is: 0001a120 (MIPS interAptiv) [ 0.310000] [vmb_cpu_active]:[268] action = 10 , cpu = 2 [ 0.310000] [vmb_cpu_start]:[908] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 2 ret1 = 9995 vpet = 608f78c4, smp_processor_id() = 0 , vpet->fw_vmb =608f78f0 !!!! [ 0.310000] [vmb_cpu_start]:[915] ret = 1 [ 0.320000] Synchronize counters for CPU 2: done. [ 0.320000] GPTC clock event init on cpu: 2 [ 0.320000] clock event init done ! [ 0.330000] [smp_init]:[553] CPU3 shouldn't run LINUX as per DT (model) config [ 0.330000] Brought up 3 CPUs [ 0.350000] pinctrl core: initialized pinctrl subsystem [ 0.350000] regulator-dummy: no parameters [ 0.360000] NET: Registered protocol family 16 [ 0.360000] [gpio_xrx500] { xrx500_gpio_init : 412 }XRX500 GPIO Driver, (C) 2014 Lantiq Deutschland Gmbh [ 0.370000] Resetting the switch and phy. [ 0.370000] dma-grx500 1e300000.dma: DMA3 base address be300000 chained_irq 77 irq_base 447 [ 0.380000] dma-grx500 1e300000.dma: Init done - hw rev: A, ports: 1, channels: 64 [ 0.390000] dma-grx500 1c100000.dma: DMA2TX base address bc100000 chained_irq 75 irq_base 399 [ 0.400000] dma-grx500 1c100000.dma: Init done - hw rev: A, ports: 1, channels: 16 [ 0.400000] dma-grx500 1c200000.dma: DMA2RX base address bc200000 chained_irq 76 irq_base 415 [ 0.410000] dma-grx500 1c200000.dma: Init done - hw rev: A, ports: 1, channels: 32 [ 0.420000] dma-grx500 1a100000.dma: DMA1TX base address ba100000 chained_irq 73 irq_base 351 [ 0.430000] dma-grx500 1a100000.dma: Init done - hw rev: A, ports: 1, channels: 16 [ 0.430000] dma-grx500 1a200000.dma: DMA1RX base address ba200000 chained_irq 74 irq_base 367 [ 0.440000] dma-grx500 1a200000.dma: Init done - hw rev: A, ports: 1, channels: 12 [ 0.450000] [gptu] { gptu_probe : 297 }dev id 16b00000.gptu [ 0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.460000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.470000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.470000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.480000] gptu-xrx500 16b00000.gptu: gptu: 4 timers loaded [ 0.480000] gptu driver init successfully [ 0.490000] [gptu] { gptu_probe : 297 }dev id 16300000.gptu [ 0.490000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.500000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.500000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.510000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.510000] gptu-xrx500 16300000.gptu: gptu: 4 timers loaded [ 0.520000] gptu driver init successfully [ 0.520000] dma0-grx500 16e00000.dma: base address b6e00000 chained_irq 72 irq_base 335 [ 0.530000] dma0-grx500 16e00000.dma: Init done - hw rev: A, ports: 4, channels: 16 [ 0.530000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1366 }disabling the BBSPI at top-mux [ 0.540000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1389 }SoC id is - 32,default XRX500 pinmuxing will used [ 0.550000] pinctrl-xrx500 pinctrl.6: Can't find mux 9 on pin21 [ 0.550000] pinctrl-xrx500 pinctrl.6: Failed to set the pin group: i2c [ 0.560000] pinctrl-xrx500 pinctrl.6: Error applying setting, reverse things back [ 0.560000] pinctrl-xrx500 pinctrl.6: failed to select default state [ 0.570000] pinctrl-xrx500 pinctrl.6: Init done [ 0.570000] gpio-xrx500 16c00000.gpio: gpio: 49 is out of the gpio chip range:(0, 32) [ 0.580000] gpio-xrx500 16c00000.gpio: gpio: 50 is out of the gpio chip range:(0, 32) [ 0.580000] gpio-xrx500 16c00000.gpio: gpio: 51 is out of the gpio chip range:(0, 32) [ 0.590000] gpio-xrx500 16c00000.gpio: gpio: 52 is out of the gpio chip range:(0, 32) [ 0.590000] gpio-xrx500 16c00000.gpio: gpio: 53 is out of the gpio chip range:(0, 32) [ 0.600000] gpio-xrx500 16c00000.gpio: gpio: 54 is out of the gpio chip range:(0, 32) [ 0.600000] gpio-xrx500 16c00000.gpio: gpio: 55 is out of the gpio chip range:(0, 32) [ 0.610000] gpio-xrx500 16c00000.gpio: gpio: 56 is out of the gpio chip range:(0, 32) [ 0.610000] gpio-xrx500 16c00000.gpio: gpio: 57 is out of the gpio chip range:(0, 32) [ 0.620000] gpio-xrx500 16c00000.gpio: gpio: 59 is out of the gpio chip range:(0, 32) [ 0.620000] gpio-xrx500 16c00000.gpio: gpio: 60 is out of the gpio chip range:(0, 32) [ 0.630000] !!!!!!! WAVE400 system registeration on AHB [ 0.640000] MTLK_MEM_BAR1_START is 14000000 [ 0.640000] MTLK_MEM_BAR1_END is 147fffff [ 0.640000] MTLK_WIRELESS_IRQ_IN_INDEX is 26 [ 0.650000] [cbm] { cbm_xrx500_probe : 6064 }2 [ 0.650000] Initializing TMU with Base Address=be700000: ... [ 0.660000] TMU Initialization Done [ 0.660000] [cbm] { init_fsqm_buf_standard : 739 }init fsqm std successfully [ 0.670000] [cbm] { init_fsqm_buf_jumbo : 780 }init fsqm jbo successfully [ 0.670000] [cbm] { init_fsqm : 665 }fsqm init successfully [ 0.680000] [cbm] { init_cbm_basic : 853 }init basic CBM successfully [ 0.680000] [cbm] { cbm_hw_init : 2032 }CBM HW init [ 0.690000] [cbm] { setup_DMA_p2p : 5402 }setup_DMA_p2p executed [ 0.690000] [cbm] { configure_ports : 5730 }tmu_port 3 [ 0.700000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.700000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.710000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.710000] [cbm] { configure_ports : 5730 }tmu_port 2 [ 0.720000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.720000] [cbm] { configure_ports : 5850 }configure_ports 7 1 0 0 8 2 [ 0.730000] [cbm] { configure_ports : 5817 }configure_ports 7 1 16 1 8 2 [ 0.730000] [cbm] { configure_ports : 5850 }configure_ports 8 1 15 0 8 2 [ 0.740000] [cbm] { configure_ports : 5817 }configure_ports 8 1 31 1 8 2 [ 0.740000] [cbm] { init_cbm_ls : 1206 }Load spreader init successfully [ 0.750000] [cbm] { cbm_xrx500_probe : 6127 }CBM Clock: 600000000Hz [ 0.750000] [cbm] { cbm_xrx500_probe : 6129 }EQM delay Enabled [ 0.760000] [cbm] { cbm_xrx500_probe : 6198 }CBM: Init Done !! [ 0.760000] PCI host bridge /ssx3@18000000/pcie@900000 ranges: [ 0.770000] MEM 0x00000000b8000000..0x00000000baffffff [ 0.770000] IO 0x00000000bb800000..0x00000000bb8fffff [ 0.880000] PCIe LCPLL SSC Mode Enabled [ 1.110000] Lantiq PCIe Root Complex Port 0 Init Done [ 1.120000] PCI host bridge /ssx3@18000000/pcie@400000 ranges: [ 1.120000] MEM 0x00000000b4000000..0x00000000b6ffffff [ 1.130000] IO 0x00000000b7800000..0x00000000b78fffff [ 1.430000] Lantiq PCIe Root Complex Port 1 Init Done [ 1.440000] PCI host bridge /ssx3@18000000/pcie@E00000 ranges: [ 1.440000] MEM 0x00000000bc000000..0x00000000beffffff [ 1.450000] IO 0x00000000bf800000..0x00000000bf8fffff [ 2.050000] pcie_wait_phy_link_up port 2 timeout [ 2.060000] pcie_rc_initialize port 2 link up failed!!!!! [ 2.060000] ltq-pcie: probe of 18e00000.pcie failed with error -5 [ 2.090000] bio: create slab <bio-0> at 0 [ 2.090000] vgaarb: loaded [ 2.100000] SCSI subsystem initialized [ 2.100000] Register xway nand done! [ 2.100000] usbcore: registered new interface driver usbfs [ 2.110000] usbcore: registered new interface driver hub [ 2.120000] usbcore: registered new device driver usb [ 2.120000] i2c-lantiq 16a00000.i2c: pins are not configured from the driver [ 2.130000] i2c-lantiq 16a00000.i2c: version 1.01 [ 2.160000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.180000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.200000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.200000] 1V15VDD: 900 <--> 1200 mV at 1790 mV normal standby [ 2.230000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.250000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.270000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.290000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.310000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.310000] try to register spd_mon driver [ 2.320000] spdmon 16080110.speedm: base address: 0xb6080110 [ 2.320000] spdmon 16080110.speedm: PHY base address: 0x16080110 [ 2.330000] device number :253 [ 2.330000] spdmon 16080110.speedm: spd_mon driver : init done !! [ 2.340000] spd_mon driver registered [ 2.340000] PCI host bridge to bus 0000:00 [ 2.350000] pci_bus 0000:00: root bus resource [mem 0xb8000000-0xbaffffff] [ 2.360000] pci_bus 0000:00: root bus resource [io 0xbb800000-0xbb8fffff] [ 2.360000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.370000] ltq-pcie 18900000.pcie: pcie_rc_class_fixup port 0: fixed pci host bridge to pci-pci bridge [ 2.380000] pci 0000:00:00.0: BAR 8: assigned [mem 0xb8000000-0xb9ffffff] [ 2.390000] pci 0000:01:00.0: BAR 0: assigned [mem 0xb8000000-0xb9ffffff] [ 2.400000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.400000] pci 0000:00:00.0: bridge window [mem 0xb8000000-0xb9ffffff] [ 2.410000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 2.410000] pci 0000:00:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.420000] pci 0000:01:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.430000] PCI host bridge to bus 0000:02 [ 2.440000] pci_bus 0000:02: root bus resource [mem 0xb4000000-0xb6ffffff] [ 2.440000] pci_bus 0000:02: root bus resource [io 0xb7800000-0xb78fffff] [ 2.450000] pci_bus 0000:02: No busn resource found for root bus, will use [bus 02-ff] [ 2.460000] ltq-pcie 18400000.pcie: pcie_rc_class_fixup port 1: fixed pci host bridge to pci-pci bridge [ 2.470000] pci 0000:02:00.0: bridge configuration invalid ([bus 03-01]), reconfiguring [ 2.480000] pci 0000:02:00.0: BAR 8: assigned [mem 0xb4000000-0xb5ffffff] [ 2.490000] pci 0000:03:00.0: BAR 0: assigned [mem 0xb4000000-0xb5ffffff] [ 2.490000] pci 0000:02:00.0: PCI bridge to [bus 03] [ 2.500000] pci 0000:02:00.0: bridge window [mem 0xb4000000-0xb5ffffff] [ 2.510000] PCI: Enabling device 0000:02:00.0 (0000 -> 0002) [ 2.510000] pci 0000:02:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.520000] pci 0000:03:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.530000] NET: Registered protocol family 8 [ 2.540000] NET: Registered protocol family 20 [ 2.540000] cfg80211: Calling CRDA to update world regulatory domain [ 2.540000] Switching to clocksource gptc-timer [ 2.580000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.600000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.620000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.640000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.660000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.680000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 2.680000] ltq_regulator_cpufreq: rcf_debugfs_init is called [ 2.690000] NET: Registered protocol family 2 [ 2.690000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 2.700000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 2.710000] TCP: Hash tables configured (established 2048 bind 2048) [ 2.710000] TCP: reno registered [ 2.720000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.720000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.730000] NET: Registered protocol family 1 [ 2.730000] RPC: Registered named UNIX socket transport module. [ 2.740000] RPC: Registered udp transport module. [ 2.740000] RPC: Registered tcp transport module. [ 2.750000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.750000] ltq-pcie 18900000.pcie: pcie_fixup_bridge port 0 : fixup host controller 0000:00:00.0 (1bef:0030) [ 2.760000] ltq-pcie 18400000.pcie: pcie_fixup_bridge port 1 : fixup host controller 0000:02:00.0 (1bef:0030) [ 2.780000] audit: initializing netlink socket (disabled) [ 2.780000] type=2000 audit(2.770:1): initialized [ 2.790000] VFS: Disk quotas dquot_6.5.2 [ 2.790000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.800000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.800000] exFAT: Version 1.2.9 [ 2.810000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 2.820000] msgmni has been set to 433 [ 2.820000] io scheduler noop registered [ 2.830000] io scheduler deadline registered (default) [ 2.830000] io scheduler cfq registered [ 2.840000] [vmb_yr_get]:[1372] CPU = 0, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 0 [ 2.850000] [vmb_yr_get]:[1372] CPU = 1, yri[i].yr_status = 1, yield_bits = 2 n_yr = 1 yri[i].cpu_id = 1 [ 2.860000] [vmb_yr_get]:[1372] CPU = 2, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 2 [ 2.870000] UMT initialize called on processor: 1 ! [ 2.870000] <umt_init>pmask addr = b2320494 and bit = 4 [ 2.880000] [vmb_tc_alloc]:[948] CPU tct[i].tc_status = 1 [ 2.880000] <umt_init>allocated TC num 2 [ 2.890000] getmvpctrl = 2 [ 2.890000] getvpectrl for target TC = 2 [ 2.890000] gettcstatus = 8400 [ 2.890000] tc is halted = 1 [ 2.890000] gettcbind = 400001 [ 2.890000] stack top = 60910ff0 [ 2.890000] start address of TC = 6032269c [ 2.890000] current TC status = a400 [ 2.890000] tc is unhalted = 0 [ 2.890000] current mvp control = 1 [ 2.920000] Yield setup passed for gptc_irq = 172 [ 2.920000] setting the gptu rate to: 25000 [ 2.930000] [gptu] { setrate : 154 }cpu_clk 200000000 [ 2.930000] [gptu] { setrate : 158 }reload_counter_value 8000 [ 2.940000] umt_init Timer 3A is running for UMT ! [ 2.950000] UMT initialize success on processor: 1 ! [ 2.950000] HW MCPY driver: Version: 1.1.0, Init Done !! [ 2.960000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.960000] lantiq,asc 16600000.serial: pins are not configured from the driver [ 2.970000] 16600000.serial: ttyLTQ0 at MMIO 0x16600000 (irq = 111) is a lantiq,asc [ 2.990000] console [ttyLTQ0] enabled, bootconsole disabled [ 2.990000] console [ttyLTQ0] enabled, bootconsole disabled [ 3.000000] Lantiq MIPSInterAptiv MPS driver, version 1.0.0.0, (c) 2006-2013 Lantiq Deutschland GmbH [ 3.010000] MPS: major Id 251 [ 3.010000] Major Id is 250 [ 3.010000] ICC driver registered [ 3.010000] sysrst_init: Trying to register System Reset Driver ... [ 3.020000] sysrst_pre_init: Detect InterAptiv CPU ... [ 3.030000] sysrst_init: Lantiq CPE GRX500 System driver version 1.0.0 [ 3.030000] sysrst_init: GRX500 System Reset initialized successfully! [ 3.040000] brd: module loaded [ 3.040000] loop: module loaded [ 3.050000] Uniform Multi-Platform E-IDE driver [ 3.050000] ide-gd driver 1.18 [ 3.060000] ONFI param page 0 valid [ 3.060000] ONFI flash detected [ 3.060000] NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown PSU1GA30DT), 128MiB, page size: 2048, OOB size: 64 [ 3.070000] Scanning device for bad blocks [ 3.140000] 7 cmdlinepart partitions found on MTD device 17c00000.nand-parts [ 3.140000] Creating 7 MTD partitions on "17c00000.nand-parts": [ 3.150000] 0x000000000000-0x000000100000 : "uboot" [ 3.160000] 0x000000100000-0x000000140000 : "ubootconfigA" [ 3.160000] 0x000000140000-0x000000180000 : "ubootconfigB" [ 3.170000] 0x000000180000-0x0000001c0000 : "gphyfirmware" [ 3.170000] 0x0000001c0000-0x0000002c0000 : "calibration" [ 3.180000] 0x0000002c0000-0x000007ec0000 : "system_sw" [ 3.180000] 0x000007ec0000-0x000008000000 : "res" [ 3.190000] Gluebi: Found kernel commandline option 'rootfsname=rootfsA' [ 3.200000] spi-lantiq-ssc 16800000.spi: master is unqueued, this is deprecated [ 3.200000] Lantiq SoC SPI controller rev 9 (TXFS 32, RXFS 32, DMA 1) [ 3.210000] [ltq_ssc] { ifx_ssc_init : 3802 }[ifx_ssc_init] force ifx_ssc_cs_low to PORT 1 [ 3.220000] [ltq_ssc] { ifx_ssc_init : 3803 }[ifx_ssc_init] force ifx_ssc_cs_high to PORT 1 [ 3.220000] [ltq_ssc] { ifx_ssc_init : 3807 }ifx_ssc_init ifx_ssc_init_count 1 [ 3.230000] [ltq_ssc] { ifx_ssc_init : 3930 }port name ltq_ssc1 [ 3.240000] [ltq_ssc] { ifx_ssc_init : 4026 }Lantiq SoC SSC controller rev 9 (TXFS 32, RXFS 32, DMA 1) [ 3.250000] [ltq_ssc] { ifx_sscAllocConnection : 3511 }ifx_sscAllocConnection ssc driver must be loaded first! [ 3.260000] ifx_spi_flash_init: failed to register sflash [ 3.270000] IMQ driver loaded successfully. (numdevs = 3, numqueues = 1) [ 3.270000] Hooking IMQ after NAT on PREROUTING. [ 3.280000] Hooking IMQ after NAT on POSTROUTING. [ 3.280000] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de [ 3.290000] Lantiq VRX318 Version 3.0.0 [ 3.290000] LTQ ETH SWITCH API, Version 3.0.2. [ 3.300000] SWAPI: Registered char device [switch_api] with major no [81] [ 3.300000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1725 (pnum:7) [ 3.310000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1792 (gswdev->gipver:48) [ 3.320000] LTQ ETH SWITCH API, Version 3.0.2. [ 3.330000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1725 (pnum:2) [ 3.340000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1792 (gswdev->gipver:48) [ 3.350000] gphy_driver_init: fw_mode:11G-FW, no of phys:5, mode:0 [ 3.350000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1686 }Loading loop_net_dev driver ...... [ 3.360000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1692 }dp_loop_eth_dev_init Succeeded! [ 3.380000] [datapath_coc] { dp_coc_new_stat_req : 803 }COC is not initialized yet in DP [ 3.380000] dp init done [ 3.390000] lro_sram_membase_res0 from DT: a2013000 [ 3.390000] ltq_toe_membase: e2000000 and lro_sram_membase_res0: e2013000 [ 3.400000] TOE Init Done !! [ 3.400000] PPP generic driver version 2.4.2 [ 3.400000] PPP BSD Compression module registered [ 3.410000] PPP Deflate Compression module registered [ 3.410000] PPP MPPE Compression module registered [ 3.420000] NET: Registered protocol family 24 [ 4.590000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.600000] ehci-pci: EHCI PCI platform driver [ 4.600000] uhci_hcd: USB Universal Host Controller Interface driver [ 4.610000] usbcore: registered new interface driver usb-storage [ 4.610000] usbcore: registered new interface driver ums-alauda [ 4.620000] usbcore: registered new interface driver ums-datafab [ 4.630000] usbcore: registered new interface driver ums-freecom [ 4.630000] usbcore: registered new interface driver ums-jumpshot [ 4.640000] usbcore: registered new interface driver ums-sddr09 [ 4.640000] usbcore: registered new interface driver ums-sddr55 [ 4.650000] usbcore: registered new interface driver ums-usbat [ 4.660000] mousedev: PS/2 mouse device common for all mice [ 4.660000] i2c-lantiq 16a00000.i2c: Register I2CCOCDRV to CPUFREQ. [ 4.690000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 4.710000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 4.710000] ina2xx 0-0040: pm: ina219, railname: PWR_12V, Rshunt: 10000 uOhm [ 4.720000] leds-gpio gpio-leds.9: pins are not configured from the driver [ 4.730000] [gptu] { setrate : 154 }cpu_clk 200000000 [ 4.730000] [gptu] { setrate : 158 }reload_counter_value 1 [ 4.740000] gpio-sso-xrx500 16d00000.sso: pins are not configured from the driver [ 4.740000] gpio-sso-xrx500 16d00000.sso: Init done [ 4.750000] Device IRQ: 97 line: 101 [ 4.750000] GlobalControl97_Capabilities_Get [ 4.760000] EIP202: PEs=1 rings=4 64-bit=No, fill level extension=No [ 4.760000] CF size=4 RF size=3 DMA len = 10 Align=0 HDW=0 HostIfc=3 [ 4.770000] EIP96 options: [ 4.770000] AES: Yes with CFB/OFB: Yes Fast: Yes [ 4.770000] DES: Yes with CFB/OFB: Yes Fast: No [ 4.770000] ARCFOUR level: 3 [ 4.770000] MD5: Yes SHA1: Yes Fast: Yes SHA256: Yes SHA512: Yes [ 4.770000] (X)CBC-MAC: Yes Fast: Yes All key sizes: No GHASH Yes [ 4.790000] EIP97 options: PEs=1, In Dbuf size=6 In Tbuf size=5, Out Dbuf size=6, Out Tbuf size=4, [ 4.790000] Token Generator: No, Transform Record Cache: No [ 4.810000] EIP206 options: PE type=0 InClassifier=0 OutClassifier=0 MAC chans=0 [ 4.810000] InDBuf=0kB InTBuf=0kB OutDBuf=0kB OutTBuf=0kB [ 4.820000] Global EIP-97 capabilities: EIP-97 v1.2p1 with EIP-202 v1.3p0 and EIP-96 v2.2p3, #PE=01 #rings=04 [ 4.830000] Global Status of the EIP-97 [ 4.840000] Packet Engine 0 Status [ 4.840000] DFE Status: CD FIFO Words: 0, CDR ID: 15, DMA size: 0 [ 4.840000] AtDMA busy: false, DataDMA busy: false, DMA err: false [ 4.850000] DSE Status: RD FIFO Words: 0, RDR ID: 15, DMA size: 0 [ 4.850000] Data flush busy: false, DataDMA busy: false, DMA err: false [ 4.860000] Token Status: Active: 0, loc available: true [ 4.860000] res available: false, read active: false, ccache active: false [ 4.860000] cntx fetch: false, res cntx: false [ 4.860000] processing held: true, busy: false [ 4.890000] Context Status: Err mask: 0000, Available: 0 [ 4.890000] Active cntx: false, next cntx: false, result cntx: false Err recov: false [ 4.900000] Interrupt Status: input DMA err: false, output DMA err false [ 4.900000] pkt proc err: false, pkt timeout: false, f a t a l err: false, PE int out: false [ 4.900000] inp DMA enable: false, outp DMA enable false, pkt proc enable: false [ 4.900000] pkt timeout enable: false, f a t a l enable: false,PE int out enable: false [ 4.930000] Output Transfer Status: availabe: 71, min: 8, max: 64, size mask: 252 [ 4.940000] PRNG Status: busy: true, res ready: false [ 4.940000] Adapter_Lock_Alloc: Lock = spinlock [ 4.950000] Adapter_Lock_Alloc: Lock = spinlock [ 4.950000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4 [ 4.960000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3 [ 4.970000] Status of CDR/RDR interface 0 [ 4.970000] CDR Status: DMA err: false, err: false: ovf/under err: false [ 4.970000] Threshold int: false, timeout int: false, FIFO count: 16 [ 4.980000] RDR Status: DMA err: false, err: false: ovf/under err: false [ 4.980000] Buf ovf: false, Descriptor ovf false [ 4.980000] Threshold int: false, timeout int: false, FIFO count: 8 [ 5.000000] LTQ Crypto Hardware Initialized .. [ 5.010000] LTQ crypto driver version: 1.2.35 [ 5.010000] usbcore: registered new interface driver usbhid [ 5.020000] usbhid: USB HID core driver [ 5.020000] Mirror/redirect action on [ 5.020000] u32 classifier [ 5.030000] Performance counters on [ 5.030000] input device check on [ 5.030000] Actions configured [ 5.040000] nf_conntrack version 0.5.0 (3468 buckets, 13872 max) [ 5.040000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 5.050000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 5.050000] xt_time: kernel timezone is -0000 [ 5.060000] ipip: IPv4 over IPv4 tunneling driver [ 5.070000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 5.070000] TCP: cubic registered [ 5.070000] Initializing XFRM netlink socket [ 5.080000] NET: Registered protocol family 10 [ 5.080000] NET: Registered protocol family 17 [ 5.090000] NET: Registered protocol family 15 [ 5.090000] Bridge firewalling registered [ 5.090000] Ebtables v2.0 registered [ 5.100000] lec:lane_module_init: lec.c: initialized [ 5.100000] mpoa:atm_mpoa_init: mpc.c: initialized [ 5.110000] KOAM is loaded successfully. [ 5.110000] l2tp_core: L2TP core driver, V2.0 [ 5.120000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 5.120000] l2tp_netlink: L2TP netlink interface [ 5.130000] 8021q: 802.1Q VLAN Support v1.8 [ 5.130000] regulator-dummy: disabling [ 5.130000] UBI: attaching mtd5 to ubi0 [ 7.410000] UBI: scanning is finished [ 7.440000] UBI: attached mtd5 (name "system_sw", size 124 MiB) to ubi0 [ 7.450000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.450000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.460000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.470000] UBI: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0 [ 7.470000] UBI: user volume: 5, internal volumes: 1, max. volumes count: 128 [ 7.480000] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 781064812 [ 7.490000] UBI: available PEBs: 338, total reserved PEBs: 654, PEBs reserved for bad PEB handling: 20 [ 7.500000] UBI: background thread "ubi_bgt0d" started, PID 553 [ 7.500000] Gluebi: mtd 'rootfsA' set to be root filesystem [ 7.500000] drivers/rtc/hctosys.c: unable to open rtc [ 7.530000] VFS: Mounted root (squashfs filesystem) readonly on device 31:8. [ 7.540000] Freeing unused memory: 296k freed rootdir=/ table='/etc/device_table.txt' [ 9.560000] UBIFS: background thread "ubifs_bgt0_4" started, PID 847 [ 9.700000] UBIFS: recovery needed [ 9.980000] UBIFS: recovery completed [ 9.980000] UBIFS: mounted UBI device 0, volume 4, name "data_vol" [ 9.980000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.990000] UBIFS: FS size: 19808256 bytes (18 MiB, 156 LEBs), journal size 1015809 bytes (0 MiB, 8 LEBs) [ 10.000000] UBIFS: reserved for root: 935592 bytes (913 KiB) [ 10.010000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 4E318B45-19DF-4D27-B360-29FDCB789BF8, small LPT model [ 10.150000] gphy-fw gphy-fw.11: proc_write_phy_fw: Found:GRX500 V1.1 GPHY BE FW [ 10.160000] gphy-fw gphy-fw.11: booting GPHY0 firmware at 27C20000 for GRX500 [ 10.160000] gphy-fw gphy-fw.11: booting GPHY1 firmware at 27C20000 for GRX500 [ 10.170000] gphy-fw gphy-fw.11: booting GPHY2 firmware at 27C20000 for GRX500 [ 10.180000] gphy-fw gphy-fw.11: booting GPHY3 firmware at 27C20000 for GRX500 [ 10.190000] gphy-fw gphy-fw.11: booting GPHY4 firmware at 27C20000 for GRX500 [ 10.190000] ltq_gphy_firmware_config: fw_mode:11G-FW, no of phys:5,data_ptr:27C20000 Enabling GMII SSC ... [TPIPF] Delete mem ... ============================== close eth1 phy power ========================= ============================== close eth1 phy power ends ==================== [ 13.850000] PPA API --- init successfully [ 13.960000] PMAC_EG_CFG_SET for GSW-L [ 13.960000] PMAC_IG_CFG_SET for GSW-L [ 13.960000] PMAC_EG_CFG_SET for GSW-R [ 13.970000] PMAC_IG_CFG_SET for GSW-R [ 13.970000] [ 13.970000] GSW PMAC Init Done!!! [ 13.980000] registering one of MII bus [ 13.980000] libphy: lantiq,xrx500-mdio: probed [ 14.000000] registering PAE MII bus [ 14.000000] libphy: lantiq,xrx500-mdio-pae: probed [ 14.010000] adding the interface: 0 [ 14.010000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 1 [ 14.020000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.020000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.030000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.030000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.040000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.040000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 6 [ 14.050000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 12 [ 14.050000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.060000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 16 port 6 sch_id 0 [ 14.070000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.080000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.080000] [cbm] { cbm_dp_port_alloc : 3549 }port id 1 [ 14.080000] no real internal PHY attached to this interface ! [ 14.090000] xrx500_of_iface: rx csum offload is enabled ! [ 14.100000] adding the interface: 1 [ 14.100000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 2 [ 14.110000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.110000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.120000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.120000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.120000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.130000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 7 [ 14.130000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 13 [ 14.140000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.150000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 17 port 7 sch_id 1 [ 14.160000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.160000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.170000] [cbm] { cbm_dp_port_alloc : 3549 }port id 2 [ 14.170000] xrx500_of_iface: rx csum offload is enabled ! [ 14.180000] trying to connect: eth0_1 to device: 0:02 with irq: 120 [ 14.220000] eth0_1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:02, irq=120) [ 14.240000] adding the interface: 2 [ 14.240000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 3 [ 14.250000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.250000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.260000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.260000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.270000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.270000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 8 [ 14.280000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 14 [ 14.280000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.290000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 18 port 8 sch_id 2 [ 14.300000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.310000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.310000] [cbm] { cbm_dp_port_alloc : 3549 }port id 3 [ 14.320000] xrx500_of_iface: rx csum offload is enabled ! [ 14.320000] trying to connect: eth0_2 to device: 0:03 with irq: 121 [ 14.370000] eth0_2: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:03, irq=121) [ 14.380000] adding the interface: 3 [ 14.390000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 4 [ 14.390000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.400000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.400000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.410000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.410000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.410000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 9 [ 14.420000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 15 [ 14.430000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.430000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 19 port 9 sch_id 3 [ 14.440000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.450000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.450000] [cbm] { cbm_dp_port_alloc : 3549 }port id 4 [ 14.460000] xrx500_of_iface: rx csum offload is enabled ! [ 14.460000] trying to connect: eth0_3 to device: 0:04 with irq: 134 [ 14.510000] eth0_3: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:04, irq=134) [ 14.530000] adding the interface: 4 [ 14.530000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 5 [ 14.530000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.540000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.540000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.550000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.550000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.560000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 10 [ 14.560000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 16 [ 14.570000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.580000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 20 port 10 sch_id 4 [ 14.580000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.590000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.600000] [cbm] { cbm_dp_port_alloc : 3549 }port id 5 [ 14.600000] xrx500_of_iface: rx csum offload is enabled ! [ 14.610000] trying to connect: eth0_4 to device: 0:05 with irq: 135 [ 14.650000] eth0_4: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:05, irq=135) [ 14.670000] adding the interface: 5 [ 14.670000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x2 port_id 6 [ 14.680000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.680000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.690000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.690000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.690000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.700000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 11 [ 14.710000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 17 [ 14.710000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.720000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 21 port 11 sch_id 5 [ 14.730000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.730000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.740000] [cbm] { cbm_dp_port_alloc : 3549 }port id 6 [ 14.740000] no real internal PHY attached to this interface ! [ 14.750000] xrx500_of_iface: rx csum offload is enabled ! [ 14.760000] adding the interface: 6 [ 14.760000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x4 port_id 15 [ 14.760000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 14.770000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 14.770000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 14.780000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 14.780000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 14.790000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 19 [ 14.790000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 14.800000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 28 port 19 sch_id 12 [ 14.810000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 14.810000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 14.820000] [cbm] { cbm_dp_port_alloc : 3549 }port id 15 [ 14.830000] xrx500_of_iface: rx csum offload is enabled ! [ 14.830000] trying to connect: eth1 to device: 1:01 with irq: 119 [ 14.880000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=1:01, irq=119) [ 14.890000] register mc group pass: 0, grp name: eth_mcgrp, grp id:6 [ 14.900000] Lantiq ethernet driver for XRX500 ! [ 15.040000] TMU HAL Init. [ 15.040000] Total node : 544 and size of each node: 7336 [ 15.050000] Total allocated size=3990784 [ 15.070000] Total node : 544 and size of each node: 7336 [ 15.090000] <hal_init> Number of CPU TMU Ports are:1 [ 15.090000] <hal_init> CPU TMU resources are Port:2 ,SB:19, Q:35 [ 15.100000] <hal_init> Number of MPE TMU Ports are:1 [ 15.100000] <hal_init> MPE TMU resources are Port:3 ,SB:20, Q:36 [ 15.110000] TMU HAL Init. [ 15.110000] Done!! [ 15.160000] Lantiq directpath datapath driver for XRX500, version lantiq_directpath_drv_xrx500.c:v1.1.1 [ 15.160000] ,(c)2009 Lantiq AG [ 15.360000] Genconf offset correct [ 15.390000] Min TC:1 Max TC:4 [ 15.390000] [vmb_cpu_alloc]:[594] CPU vpet[j].cpu_status = 11 [ 15.390000] [vmb_yr_get]:[1372] CPU = 3, yri[i].yr_status = 1, yield_bits = 2 n_yr = 1 yri[i].cpu_id = 3 q]u[s4d5 APT g t IIQin e1r p! launch from cpu 03 MSG_ID = 01[ 15.400000] [vmb_tc_alloc]:[948] CPU tct[i].tc_status = 1 [ 15.400000] [vmb_yr_get]:[1372] CPU = 3, yri[i].yr_status = 1, yield_bits = 4 n_yr = 1 yri[i].cpu_id = 3 [ 15.400000] [fw_vmb_get_irq]:[1475] CPU = 3 IRQ = 110 !!! [ 15.400000] mpe_hal_to_vmb_callback_hdlr not support status 0x0 [ 15.410000] [vmb_cpu_start]:[849] vmb_fw_msg_t = a0000218 cpu = 3 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!! [ 15.410000] [gic_trigger]:[559] VMB_CPU_IPI3 - 85 CPU = 3 [ 15.420000] [fw_vmb_ipi3_hdlr]:[166] CPU = 0 irq = 110 [ 15.420000] [fw_vmb_ipi3_hdlr]:[173] cid = 1 , vid = 1 [ 15.420000] [fw_vmb_ipi3_hdlr]:[210] [ 15.420000] [fw_vmb_ipi3_hdlr]:[212] [ 15.420000] vmb_wq = 608f7918 [ 15.420000] [vmb_cpu_start]:[892] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!! [ 15.420000] [vmb_cpu_start]:[908] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 3 ret1 = 9999 vpet = 608f78fc, smp_processor_id() = 0 , vpet->fw_vmb =608f7928 !!!! [ 15.420000] [ 15.420000] [vmb_cpu_start]:[915] ret = 1 [ 15.420000] <mpe_hal_set_fw_connectivity> CPU TMU resources for MPE are Port:3 ,SB:20, Q:36 SLvl:1 [ 15.420000] MPE HAL Run FW success . [ 15.420000] MPE Proc Creation....!!! [ 15.420000] <mpe_hal_set_ipsec_loopback_connectivity> Enter [ 15.420000] add "loopdev0" successfully [ 15.420000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x40 port_id 0 [ 15.420000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 15.420000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 15.420000] [cbm] { cbm_dp_port_alloc : 3446 }port id 7 [ 15.420000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 255 [ 15.420000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 15.420000] [cbm] { cbm_dp_port_alloc : 3493 }no further action required [ 15.420000] <tmu_hal_setup_dp_ingress_connectivity> TMU resources for Checksum is Port:20 ,SB:13, Q:29 SLvl: 1 [ 15.420000] For Loopdev device Q:30 [ 15.420000] Redirect Port 7 is configured [ 15.580000] DC DP [dc_dp_reserve_port:1361] Trying to reserve multiport0=2!!! [ 15.580000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x0 port_id 0 [ 15.580000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 15.580000] [cbm] { resv_dp_res : 3089 }even_first 1 [ 15.580000] [cbm] { resv_dp_res : 3099 }Alloc 0x1 resv 0x0 [ 15.580000] [cbm] { resv_dp_res : 3105 }f_found 8 [ 15.580000] [cbm] { resv_dp_res : 3124 }found the pair 9 8 [ 15.580000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 15.580000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 15.580000] DC DP [dc_dp_reserve_port:1389] Successfully reserved multiport0=2 start_port_id=8!!! ACTION=add ACTION=remove DEVICENAME=MPE_FW.0 DEVICENAME=MPE_FW.0 [ 15.800000] L2NAT:l2nat_init:859 l2nat module loaded [ 15.960000] Init Success [ 15.960000] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 572 }ppa_hal_generic_hook not support cmd 0xd [ 15.970000] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 572 }ppa_hal_generic_hook not support cmd 0xd [ 15.980000] directpath start id: 0, end id: 272 [ 15.980000] ppa_init - init succeeded [ 16.000000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 16.010000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 16.010000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 16.020000] p2p channel turned ON ! [ 16.020000] resume phy for device: eth0_1 [ 16.030000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready [ 16.040000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 16.050000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 16.050000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 16.060000] p2p channel already ON ! [ 16.060000] resume phy for device: eth0_2 [ 16.070000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 16.080000] [cbm] { cbm_dp_enable : 3855 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 16.080000] [cbm] { cbm_dp_enable : 3886 }enable queue 19 [ 16.090000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 16.100000] p2p channel already ON ! [ 16.100000] resume phy for device: eth0_3 [ 16.110000] IPv6: ADDRCONF(NETDEV_UP): eth0_3: link is not ready [ 16.110000] [cbm] { cbm_dp_enable : 3855 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 16.120000] [cbm] { cbm_dp_enable : 3886 }enable queue 20 [ 16.120000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 16.130000] p2p channel already ON ! [ 16.140000] resume phy for device: eth0_4 [ 16.140000] IPv6: ADDRCONF(NETDEV_UP): eth0_4: link is not ready [ 16.150000] [cbm] { cbm_dp_enable : 3855 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 16.160000] [cbm] { cbm_dp_enable : 3886 }enable queue 28 [ 16.160000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 16.170000] p2p channel already ON ! [ 16.170000] resume phy for device: eth1 [ 16.180000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready ============================== close eth1 phy power ========================= ============================== close eth1 phy power ends ==================== [ 16.310000] device eth0_1 entered promiscuous mode [ 16.320000] device eth0_2 entered promiscuous mode [ 16.330000] device eth0_3 entered promiscuous mode [ 16.330000] device eth0_4 entered promiscuous mode [ 16.430000] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 16.440000] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 16.440000] xhci_gen_setup() 4765 MSWAP=0 [ 16.450000] xhci_gen_setup() 4766 VERSION=0x0100 [ 16.450000] xhci_gen_setup() 4767 HC_LENGTH=0x20 [ 16.460000] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0x1a300000 [ 16.460000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.470000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.480000] usb usb1: Product: xHCI Host Controller [ 16.480000] usb usb1: Manufacturer: Linux 3.10.104 xhci-hcd [ 16.490000] usb usb1: SerialNumber: xhci-hcd.0.auto [ 16.490000] hub 1-0:1.0: USB hub found [ 16.500000] hub 1-0:1.0: 1 port detected [ 16.500000] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 16.510000] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 16.510000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 16.520000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.530000] usb usb2: Product: xHCI Host Controller [ 16.530000] usb usb2: Manufacturer: Linux 3.10.104 xhci-hcd [ 16.540000] usb usb2: SerialNumber: xhci-hcd.0.auto [ 16.540000] hub 2-0:1.0: USB hub found [ 16.550000] hub 2-0:1.0: 1 port detected [ 16.550000] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 16.560000] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 16.560000] xhci_gen_setup() 4765 MSWAP=0 [ 16.570000] xhci_gen_setup() 4766 VERSION=0x0100 [ 16.570000] xhci_gen_setup() 4767 HC_LENGTH=0x20 [ 16.580000] xhci-hcd xhci-hcd.1.auto: irq 91, io mem 0x1a500000 [ 16.580000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 16.590000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.600000] usb usb3: Product: xHCI Host Controller [ 16.600000] usb usb3: Manufacturer: Linux 3.10.104 xhci-hcd [ 16.610000] usb usb3: SerialNumber: xhci-hcd.1.auto [ 16.610000] hub 3-0:1.0: USB hub found [ 16.620000] hub 3-0:1.0: 1 port detected [ 16.620000] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 16.620000] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 16.630000] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 16.640000] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 16.650000] usb usb4: Product: xHCI Host Controller [ 16.650000] usb usb4: Manufacturer: Linux 3.10.104 xhci-hcd [ 16.660000] usb usb4: SerialNumber: xhci-hcd.1.auto [ 16.660000] hub 4-0:1.0: USB hub found [ 16.670000] hub 4-0:1.0: 1 port detected [ 17.080000] fuse init (API version 7.22) [ 17.220000] tfat: module license 'Commercial. For support email exfat-support@tuxera.com' taints kernel. [ 17.230000] Disabling lock debugging due to kernel taint [ 17.240000] Tuxera FAT 12/16/32 driver version 3017.7.24.1 [Flags: R/W MODULE]. [ 17.250000] Built against headers 3.10.104 #8 SMP Fri May 10 10:48:44 CST 2019 mips [ 17.250000] Running on kernel 3.10.104 #1 SMP Wed Jul 8 13:17:08 CST 2020 mips [ 17.490000] Tuxera NTFS driver 3017.7.4.6 [Flags: R/W MODULE]. [ 17.500000] Built against headers 3.10.104 #8 SMP Fri May 10 10:48:44 CST 2019 mips [ 17.510000] Running on kernel 3.10.104 #1 SMP Wed Jul 8 13:17:08 CST 2020 mips [ 17.580000] Tuxera HFS+ driver 3014.7.28- preinit - - regular preinit - jffs2 not ready yet; using ramdisk [ 17.690000] UBIFS error (pid 1074): ubifs_mount: cannot open "ubi0:ubi_rootfs_data", error -19 - init - Please press Enter to activate this console. [ 20.570000] Registeration is a success The major device number is 248. [ 20.580000] proc initialized[ 20.590000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 20.840000] sysctl: The scan_unevictable_pages sysctl/node-interface has been disabled for lack of a legitimate use case. If you have one, please send an email to linux-mm@kvack.org. [ 21.410000] tun: Universal TUN/TAP device driver, 1.6 [ 21.410000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 21.430000] usb cycle succeed [ 21.490000] sit: IPv6 over IPv4 tunneling driver [ 21.530000] gre: GRE over IPv4 demultiplexor driver [ 21.540000] ip_gre: GRE over IPv4 tunneling driver [ 21.700000] PPTP driver version 0.8.5 [ 22.090000] nf_conntrack_rtsp v0.6.21 loading [ 22.130000] nf_nat_rtsp v0.6.21 loading [ 22.170000] Netfilter messages via NETLINK v0.30. [ 22.190000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 22.310000] ctnetlink v0.93: registering with nfnetlink. ------------------------------------------------------------------------------------- reloadprofile() begin reloadprofile() end ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- reloadconfig() begin ................................start of merge user and default........................ ................................parse userconf to get mode............................. ................................end of parse userconf.................................. ................................mode : router............................... ................................end of merge user and default.......................... ................................new configs merged..................................... reloadconfig() end ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------- [ 26.220000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 26.230000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 26.240000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 26.240000] br-lan: port 1(eth0_1) entered disabled state [ 26.270000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 26.280000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 26.280000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 26.290000] p2p channel already ON ! [ 26.290000] phy init already done ! [ 26.290000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready [ 26.310000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 26.320000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 26.320000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 26.330000] br-lan: port 2(eth0_2) entered disabled state [ 26.360000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 26.360000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 26.360000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 26.380000] p2p channel already ON ! [ 26.380000] phy init already done ! [ 26.380000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 26.400000] [cbm] { cbm_dp_enable : 3855 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 26.410000] [cbm] { cbm_dp_enable : 3886 }enable queue 19 [ 26.410000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 26.420000] br-lan: port 3(eth0_3) entered disabled state [ 26.450000] [cbm] { cbm_dp_enable : 3855 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 26.450000] [cbm] { cbm_dp_enable : 3886 }enable queue 19 [ 26.450000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 26.470000] p2p channel already ON ! [ 26.470000] phy init already done ! [ 26.470000] IPv6: ADDRCONF(NETDEV_UP): eth0_3: link is not ready [ 26.490000] [cbm] { cbm_dp_enable : 3855 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 26.500000] [cbm] { cbm_dp_enable : 3886 }enable queue 20 [ 26.500000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 26.510000] br-lan: port 4(eth0_4) entered disabled state [ 26.540000] [cbm] { cbm_dp_enable : 3855 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 26.540000] [cbm] { cbm_dp_enable : 3886 }enable queue 20 [ 26.540000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 26.550000] p2p channel already ON ! [ 26.560000] phy init already done ! [ 26.560000] IPv6: ADDRCONF(NETDEV_UP): eth0_4: link is not ready USB port event happened -- port= USB port event happened -- port= USB port event happened -- port= 1 and 00 and 780 gmtoff: 0:00 and tz: -0:00 GMT-0:00DST-1:00,M3.5.0/1,M10.4.0/1 USB port event happened -- port= [ wifi_firm]debug label Start Intel WLAN... [ 29.930000] UBI error: ubi_open_volume: cannot open device 0, volume 4, error -16 [ 30.570000] udevd[2119]: starting version 173 [ 30.810000] cfg80211: World regulatory domain updated: [ 30.820000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 30.830000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 30.830000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm) [ 30.840000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) [ 30.850000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) [ 30.860000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm) [ 30.860000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm) [ 30.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) [ 30.880000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) insert kernel modules [ 30.990000] [MTLKD] Allocated netdev rtlog0 addr 6fa4f800 [ 31.000000] [4294940396] mtlk0(mtlk_cdev_init:311): Max nodes set to 1048575 RCVRY:FAPI SOCKET INIT in progress wait 0 of 15 [ 32.140000] [4294940510] mtlk0(__mtlk_print_endianess:9218): The system is Big endian (0xbeadfeed, 0xedfeadbe) [ 32.150000] [4294940511] mtlk0(__mtlk_print_driver_version:9225): Driver version: 6.0.8.0.87.0.7.exported.d24084bd3447.bugfix/rel_6.0.8.0.87.PcieG5.PcieG6.Release [ 32.160000] [4294940512] mtlk0(mtlk_fast_mem_print_info:115): Using normal memory for hot context [ 32.170000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 32.170000] [4294940513] mtlk0(_pci_mem_get:615): PCI Memory block 0: PA: 0xb8000000, VA: 0xf8000000, Len=0x2000000 [ 32.190000] [MTLKD] PCIE bus ChipID is:0x0900 address is:0xf8220060 [ 32.190000] [4294940515] mtlkW(_pci_start:706): CID-00: Detecting DUAL PCI mode... [ 32.200000] [MTLKD] RCU_BOOT: 0x00003007, mspsStatus: 0x00, address: 0xf827000c [ 32.210000] [MTLKD] DUAL PCI mode is detected [ 32.210000] [MTLKD] PCIE bus ChipID is:0x0900 address is:0xf8220060 [ 32.220000] [4294940518] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('cal_wlan0.bin') is starting [ 32.410000] [4294940537] mtlk0(_eeprom_parse:900): EEPROM info: ver 0x0600, cal_file_type Operational, device_id 0x0900, header size 40, data size 1024, is_cis_v6 1 [ 32.420000] [4294940538] mtlk0(mtlk_cis_data_parse:1148): EEPROM Card ID: type 0x61, revision 0x46 (F) [ 32.430000] [4294940539] mtlk0(_mtlk_cis_search_and_parse_rssi_v6:1078): RSSI CIS found ant_mask 0x0A, freq 5190, band 0 [ 32.440000] [4294940540] mtlk0(_mtlk_cis_search_and_parse_rssi_v6:1078): RSSI CIS found ant_mask 0x05, freq 2442, band 1 [ 32.450000] [4294940541] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 0, antenna 1 [ 32.460000] [4294940542] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 0, antenna 3 [ 32.470000] [4294940543] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 0, antenna 1 [ 32.480000] [4294940544] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 0, antenna 3 [ 32.490000] [4294940545] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 0, antenna 1 [ 32.490000] [4294940545] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 0, antenna 3 [ 32.500000] [4294940546] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 0, antenna 1 [ 32.510000] [4294940547] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 0, antenna 3 [ 32.520000] [4294940548] mtlk0(_parse_tpc_g6:888): TPC data for chan 132, bw 0, antenna 1 [ 32.530000] [4294940549] mtlk0(_parse_tpc_g6:888): TPC data for chan 132, bw 0, antenna 3 [ 32.540000] [4294940550] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 1, antenna 1 [ 32.540000] [4294940550] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 1, antenna 3 [ 32.550000] [4294940551] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 1, antenna 1 [ 32.560000] [4294940552] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 1, antenna 3 [ 32.570000] [4294940553] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 1, antenna 1 [ 32.580000] [4294940554] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 1, antenna 3 [ 32.580000] [4294940554] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 1, antenna 1 [ 32.590000] [4294940555] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 1, antenna 3 [ 32.600000] [4294940556] mtlk0(_parse_tpc_g6:888): TPC data for chan 132, bw 1, antenna 1 [ 32.610000] [4294940557] mtlk0(_parse_tpc_g6:888): TPC data for chan 132, bw 1, antenna 3 [ 32.620000] [4294940558] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 2, antenna 1 [ 32.620000] [4294940558] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 2, antenna 3 [ 32.630000] [4294940559] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 2, antenna 1 [ 32.640000] [4294940560] mtlk0(_parse_tpc_g6:888): TPC data for chan 52, bw 2, antenna 3 [ 32.650000] [4294940561] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 2, antenna 1 [ 32.660000] [4294940562] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 2, antenna 3 [ 32.670000] [4294940563] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 2, antenna 1 [ 32.670000] [4294940563] mtlk0(_parse_tpc_g6:888): TPC data for chan 116, bw 2, antenna 3 [ 32.680000] [4294940564] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 3, antenna 1 [ 32.690000] [4294940565] mtlk0(_parse_tpc_g6:888): TPC data for chan 36, bw 3, antenna 3 [ 32.700000] [4294940566] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 3, antenna 1 [ 32.710000] [4294940567] mtlk0(_parse_tpc_g6:888): TPC data for chan 100, bw 3, antenna 3 [ 32.710000] [4294940567] mtlk0(_parse_tpc_g6:888): TPC data for chan 7, bw 0, antenna 0 [ 32.720000] [4294940568] mtlk0(_parse_tpc_g6:888): TPC data for chan 7, bw 0, antenna 2 [ 32.730000] [4294940569] mtlk0(_parse_tpc_g6:888): TPC data for chan 5, bw 1, antenna 0 [ 32.740000] [4294940570] mtlk0(_parse_tpc_g6:888): TPC data for chan 5, bw 1, antenna 2 [ 32.750000] [4294940571] mtlk0(_parse_tpc_g6:888): TPC data for chan 7, bw 3, antenna 0 [ 32.750000] [4294940571] mtlk0(_parse_tpc_g6:888): TPC data for chan 7, bw 3, antenna 2 [ 32.760000] [4294940572] mtlk0(_mtlk_cis_area_parse_g6:964): EEPROM: TX antennas number 4, mask 0x0F [ 32.770000] [4294940573] mtlk0(mtlk_cis_data_parse:1217): EEPROM supported bands: 2.4 - Yes, 5.2 - Yes [ 32.780000] [4294940574] mtlkW(mtlk_cis_data_parse:1220): EEPROM contain TPC data for both bands [ 32.790000] [4294940575] mtlk0(_mtlk_pcieg6_efuse_access_check:2043): eFuse read: addr 0, size 128, buf 0x6c5bc700 [ 32.800000] [4294940576] mtlk0(_mtlk_hw_fill_card_info:3536): is_asic:1, is_emul:0, is_fpga:0, is_phy_dummy:0 [ 32.810000] [4294940577] mtlk0(_wave_hw_cfg_platform_type_set:7094): TestPlatformType: 0 [ 32.820000] [4294940578] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('PSD.bin') is starting [ 32.840000] [4294940580] mtlk0(mtlk_psdb_file_read_and_parse:1958): PSDB Info: version 121 (0x00000079), revision 00 [ 32.850000] [4294940581] mtlk0(mtlk_psdb_file_read_and_parse:1967): Look for chip_id 0x0900, hw_type 0x61, hw_rev 0x46 [ 32.870000] [4294940582] mtlk0(psdb_parse_fields_array:1636): Parsed 62 items, found 12 fields and 23 tables [ 32.880000] [4294940584] mtlk0(_mtlk_psdb_parse_ant_mask_per_chan_table:1546): Channel until 35 (including) mask is 0x05 [ 32.890000] [4294940585] mtlk0(_mtlk_psdb_parse_ant_mask_per_chan_table:1546): Channel until 255 (including) mask is 0x0A [ 32.900000] [4294940586] mtlk0(_mtlk_psdb_parse_cdb_cfg_table:1307): CDB config[0] = 1 (CDB_CFG_2G) [ 32.910000] [4294940587] mtlk0(_mtlk_psdb_parse_cdb_cfg_table:1307): CDB config[1] = 2 (CDB_CFG_5G) [ 32.920000] [4294940588] mtlk0(psdb_parse_fields_array:1788): PSDB: TX/RX antennas number 4/4, mask 0x0F/0x0F [ 32.930000] [4294940589] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1473): [0] band 1, channels 1 ... 14 [ 32.940000] [4294940590] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1479): [0] Antennas number 2, mask 05, sel_mask 11, factor 24 [ 32.950000] [4294940591] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1473): [1] band 0, channels 36 ... 165 [ 32.960000] [4294940592] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1479): [1] Antennas number 2, mask 0A, sel_mask 44, factor 24 [ 32.970000] [4294940593] mtlk0(_psdb_print_info:1894): PSDB Beamforming capabilities: 0x1C, bf_explicit=1 [ 32.980000] [4294940594] mtlk0(wave_rcvry_card_add:403): Creating dir FW [ 32.980000] [4294940594] mtlk0(wave_rcvry_card_add:411): Number of files to create 25 [ 32.990000] [4294940595] mtlk0(_mmb_drv_radio_number_get:1426): card_idx:0, number of radios supported:2, configured:2 [ 33.000000] [4294940596] mtlk0(mtlk_hw_mmb_init_card:7140): card_idx:0, mmb_base:0xf8000000, mmb_pas:0xf8300000, mmb_pas_phy:0xb8000000, fastpath supported:1 enabled:1 -> available:1 [ 33.020000] [4294940598] mtlk0(_wave_hw_radio_band_cfg_init:12364): Gen5: 0, Gen6: 1, band_cfg_sys_mode: WAVE_HW_RADIO_BAND_CFG_DB_2x2, ep_mask: 1, vap_mask: 15 [ 33.030000] [4294940599] mtlk0(_wave_hw_radio_band_cfg_init:12370): HW supports max VAPs 16 (32 in FW) max STAs 254 [ 33.040000] [4294940600] mtlk0(wave_radio_limits_set:4375): Radio ID 0 supports max VAPs 8 max STAs 127 [ 33.050000] [4294940601] mtlk0(wave_radio_limits_set:4375): Radio ID 1 supports max VAPs 8 max STAs 127 [ 33.060000] [4294940602] mtlk0(_wave_hw_dual_pci_mode_set:7080): dual PCI mode ON [ 33.070000] [4294940603] mtlk0(mtlk_df_dcdp_get_host_capability:11300): DC DP library version: 0.0.0 (0x00000000) [ 33.080000] [4294940604] mtlk0(mtlk_df_dcdp_get_host_capability:11303): DC DP headers version: 4.1.4 (0x00040104) [ 33.090000] [4294940605] mtlk0(mtlk_df_dcdp_get_host_capability:11306): FastPath: supported [ 33.100000] [4294940606] mtlk0(mtlk_df_dcdp_get_host_capability:11313): LitePath: supported [ 33.110000] [4294940607] mtlk0(mtlk_df_dcdp_get_host_capability:11314): SWPath: supported [ 33.110000] [4294940607] mtlk0(mtlk_df_dcdp_datapath_dev_init:11352): Activate fragmentation W/A [ 33.120000] [4294940608] mtlk0(pci_irq_alloc:835): CID-00: Interrupt configuration: using legacy interrupt mode [ 33.130000] [4294940609] mtlk0(_mtlk_pcieg6_reset_mac:842): Reset WLAN SOC: address is 0x00270004, value=0x00000001 [ 33.160000] [4294940612] mtlk0(__pcieg6_reset_cpu_lower:790): Reset LMAC0 [ 33.190000] [4294940615] mtlk0(__pcieg6_reset_cpu_lower:790): Reset LMAC1 [ 33.220000] [4294940618] mtlk0(_mtlk_pcieg6_put_cpus_to_reset:872): Reset UMAC [ 33.250000] [4294940621] mtlk0(_mtlk_mmb_cleanup_reset_mac:5277): FW CPU reset is done [ 33.250000] [4294940621] mtlk0(_abb_central_fusing:1324): Trim by AFE data [ 33.260000] [MTLKD] ibiastrim 0x02 [ 33.260000] [MTLKD] vreftrim 0x0B [ 33.270000] [MTLKD] ldo_central_pll1v8 0x04 [ 33.270000] [MTLKD] ldo_central_pllref 0x02 [ 33.280000] [MTLKD] ldo_central_pllpost 0x02 [ 33.280000] [MTLKD] iptattrim 0x0A [ 33.280000] [MTLKD] ldo_central_clkd 0x05 [ 33.290000] [MTLKD] ldo_central_clkin 0x05 [ 33.290000] [MTLKD] (1125) wrToAfeRegC addr 0x0040 value 0x0BA2 [ 33.300000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x0040, data 0x0080 [ 33.310000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x0040, data 0x0BA2 [ 33.310000] [MTLKD] (1125) wrToAfeRegC addr 0x0045 value 0x0005 [ 33.320000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x0045, data 0x0008 [ 33.330000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x0045, data 0x0005 [ 33.330000] [MTLKD] (1125) wrToAfeRegC addr 0x005E value 0x0004 [ 33.340000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x005E, data 0x0004 [ 33.350000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x005E, data 0x0004 [ 33.350000] [MTLKD] (1125) wrToAfeRegC addr 0x005C value 0x0002 [ 33.360000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x005C, data 0x0008 [ 33.370000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x005C, data 0x0002 [ 33.370000] [MTLKD] (1125) wrToAfeRegC addr 0x005D value 0x0002 [ 33.380000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x005D, data 0x0008 [ 33.390000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x005D, data 0x0002 [ 33.390000] [MTLKD] (1125) wrToAfeRegC addr 0x0047 value 0x0005 [ 33.400000] [MTLKD] (1087) FCSI_READ ms 1, rf 0, addr 0x0047, data 0x0008 [ 33.400000] [MTLKD] (1099) FCSI_WRITE ms 1, rf 0, addr 0x0047, data 0x0005 [ 33.430000] [4294940639] mtlkW(_wave_hw_chi_area_write:4181): hdr 6c7207a8, id 12 [ 33.430000] [4294940639] mtlkW(_wave_hw_chi_area_write:4187): dst 6c7207b4, data 0x01 [ 33.440000] [4294940640] mtlkW(_wave_hw_chi_area_write:4187): dst 6c7207b8, data 0x01 [ 33.450000] [4294940641] mtlkW(_wave_hw_chi_area_write:4187): dst 6c7207bc, data 0x00 [ 33.460000] [4294940642] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ap_ram_gen6_wrx_600_real_phy.bin') is starting [ 33.890000] [4294940685] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('tx_sender_gen6.bin') is starting [ 33.900000] [cbm] { cbm_dp_enable : 3855 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 33.910000] [cbm] { cbm_dp_enable : 3886 }enable queue 28 [ 33.920000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 33.930000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 33.930000] [4294940689] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('tx_sender_gen6.bin') is starting [ 33.930000] [4294940689] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('host_interface_gen6_dc_mode0.bin') is starting [ 33.950000] [4294940691] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('rx_handler_gen6.bin') is starting [ 33.970000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 33.980000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 33.980000] [4294940694] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('rx_handler_gen6.bin') is starting [ 33.980000] [4294940694] mtlk0(__pcieg6_release_cpu_lower:802): Release LMAC0 [ 34.000000] br-lan: port 1(eth0_1) entered disabled state [ 34.010000] [4294940697] mtlk0(__pcieg6_release_cpu_lower:802): Release LMAC1 [ 34.010000] device eth0_1 left promiscuous mode [ 34.010000] br-lan: port 1(eth0_1) entered disabled state [ 34.030000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 34.030000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 34.030000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 34.040000] br-lan: port 2(eth0_2) entered disabled state [ 34.050000] [4294940701] mtlk0(_mtlk_pcieg6_release_cpus_reset:1626): Release UMAC [ 34.060000] device eth0_2 left promiscuous mode [ 34.060000] br-lan: port 2(eth0_2) entered disabled state [ 34.070000] [cbm] { cbm_dp_enable : 3855 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 34.080000] [cbm] { cbm_dp_enable : 3886 }enable queue 19 [ 34.080000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 34.090000] [4294940705] mtlk0(_mtlk_mmb_wait_chi_magic:4273): Wait for CHI Magic (5000 ms)... [ 34.090000] br-lan: port 3(eth0_3) entered disabled state [ 34.100000] [4294940706] mtlk0(__log_chi_area:4502): Line 7930: CHI: sFifoQ: is=0x47f4 in=16 rs=0x4834 rn=16 [ 34.100000] device eth0_3 left promiscuous mode [ 34.100000] br-lan: port 3(eth0_3) entered disabled state [ 34.120000] [4294940708] mtlk0(__log_chi_area:4502): Line 7931: CHI: sDAT: is=0x47d0 in=1 rs=0x0 rn=0 [ 34.130000] [4294940709] mtlk0(__log_chi_area:4502): Line 7932: CHI: sMAN: is=0x516c in=8 rs=0x4c94 rn=2 [ 34.140000] [4294940710] mtlk0(__log_chi_area:4502): Line 7933: CHI: sDBG: is=0x4874 in=1 rs=0x4a84 rn=1 [ 34.150000] [4294940711] mtlk0(__log_chi_ring:4522): Line 7935: CHI: sMangTxRING: inCounter=0x2550dc inStatus=0x25512c outCounter=0x25510c outStatus=0x255134 inCounter_BE=0x0 outFreedCounter_BE=0x0 [ 34.170000] [4294940713] mtlk0(__log_chi_ring:4522): Line 7936: CHI: sMangRxRING: inCounter=0x2550d8 inStatus=0x255128 outCounter=0x255108 outStatus=0x255130 inCounter_BE=0x0 outFreedCounter_BE=0x0 [ 34.180000] [4294940714] mtlk0(__log_chi_ring:4522): Line 7938: CHI: sTxRING: inCounter=0x2550cc inStatus=0x25511c outCounter=0x2550fc outStatus=0x255124 inCounter_BE=0x255254 outFreedCounter_BE=0x2359fc [ 34.210000] [4294940717] mtlk0(__log_chi_ring:4522): Line 7939: CHI: sRxRING: inCounter=0x2550c8 inStatus=0x255118 outCounter=0x2550f8 outStatus=0x255120 inCounter_BE=0x255250 outFreedCounter_BE=0x2359f8 [ 34.230000] [4294940719] mtlk0(__log_chi_pool:4535): Line 7940: CHI: sRdPOOL: RdPoolBaseAddress=0x44fb80 RdSizeInBytes=0x20 PayloadAddressOffsetInRd=0x0 BdIndexOffsetInRd=0x1c NumRdsInPool=2048 NumMgtRdsInPool=128 [ 34.250000] [4294940721] mtlk0(_mtlk_mmb_prepare_ring_counters:4645): Ring Regs: p_IN_cntr 0xf82550cc, p_OUT_status 0xf8255124, p_OUT_cntr 0xf82550fc [ 34.260000] [4294940722] mtlk0(_mtlk_mmb_prepare_ring_counters:4645): Ring Regs: p_IN_cntr 0xf82550c8, p_OUT_status 0xf8255120, p_OUT_cntr 0xf82550f8 [ 34.280000] [4294940723] mtlk0(_mtlk_mmb_prepare_ring_buffer:4685): ring_size:128 total_ring_size:2560 [ 34.280000] [4294940724] mtlk0(_mtlk_mmb_prepare_ring_buffer:4718): Ring virtual addr:67aaf000 dma_addr:27aaf000 base_addr:a7aaf000 [ 34.300000] [4294940726] mtlk0(_mtlk_mmb_prepare_ring_counters:4645): Ring Regs: p_IN_cntr 0xf82550d8, p_OUT_status 0xf8255130, p_OUT_cntr 0xf8255108 [ 34.310000] [4294940727] mtlk0(_mtlk_mmb_prepare_ring_buffer:4685): ring_size:128 total_ring_size:2560 [ 34.320000] [4294940728] mtlk0(_mtlk_mmb_prepare_ring_buffer:4718): Ring virtual addr:67b44000 dma_addr:27b44000 base_addr:a7b44000 [ 34.330000] [4294940729] mtlk0(_mtlk_mmb_prepare_ring_counters:4645): Ring Regs: p_IN_cntr 0xf82550dc, p_OUT_status 0xf8255134, p_OUT_cntr 0xf825510c [ 34.340000] [4294940730] mtlk0(_mtlk_mmb_init_calibration_cache:5333): u32BufferRequestedSize 127152, pPsdProgmodelAddress 0x0014 [ 34.360000] [4294940732] mtlk0(_mtlk_mmb_set_calibration_buffers:5320): Calibration buffer: dma_addr 0x27460000, virt_addr 0x67460000, size 127152 [ 34.370000] [4294940733] mtlk0(wv_cfg80211_init_band:1804): 2.4 GHz band supported, up to 2 spatial streams [ 34.380000] [4294940734] mtlk0(_wave_radio_vap_create:422): ndev_name wlan0, vap_id 0 [ 34.390000] [cbm] { cbm_dp_enable : 3855 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 34.400000] [cbm] { cbm_dp_enable : 3886 }enable queue 20 [ 34.400000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 34.410000] br-lan: port 4(eth0_4) entered disabled state [ 34.410000] [4294940737] mtlk0(wave_hw_band_hd_ep_bit_get:12448): band_cfg: WAVE_HW_RADIO_BAND_CFG_DB_2x2 radio_id: 0 vap_id: 0 --> ep_bit: 1, vap_id_fw 16 [ 34.430000] [4294940739] mtlk0(_mtlk_df_user_alloc_devname:9169): dev_alloc_name succeeded, pattern:wlan0, name:wlan0 [ 34.440000] [4294940740] mtlk0(wv_cfg80211_init_band:1804): 5 GHz band supported, up to 2 spatial streams [ 34.440000] device eth0_4 left promiscuous mode [ 34.440000] br-lan: port 4(eth0_4) entered disabled state [ 34.460000] [4294940742] mtlk0(_wave_radio_vap_create:422): ndev_name wlan2, vap_id 0 [ 34.470000] [4294940743] mtlk0(wave_hw_band_hd_ep_bit_get:12448): band_cfg: WAVE_HW_RADIO_BAND_CFG_DB_2x2 radio_id: 1 vap_id: 0 --> ep_bit: 0, vap_id_fw 0 [ 34.480000] [4294940744] mtlk0(_mtlk_df_user_alloc_devname:9169): dev_alloc_name succeeded, pattern:wlan2, name:wlan2 [ 34.490000] [4294940745] mtlk0(mtlk_hw_mmb_start_card_finalize:8005): mips_no:0, pas_offset:0x0004E86C [ 34.490000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 34.490000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 34.490000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 34.490000] p2p channel already ON ! [ 34.490000] phy init already done ! [ 34.490000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready [ 34.490000] device eth0_1 entered promiscuous mode [ 34.540000] [4294940750] mtlk0(mtlk_hw_mmb_start_card_finalize:8005): mips_no:1, pas_offset:0x0004E870 [ 34.550000] [4294940751] mtlk0(mtlk_hw_mmb_start_card_finalize:8005): mips_no:2, pas_offset:0x0004E874 [ 34.560000] [4294940752] mtlkW(_mtlk_get_rx_ring_size:4766): RX ring size 4096 defined bigger than RD pool size 2048, using RD pool size as ring size [ 34.570000] [4294940753] mtlk0(mtlk_df_dcdp_datapath_dev_register:11525): Registering DirectConnect dev_port 0 [ 34.580000] DC DP [dc_dp_alloc_port:182] owner=6b72816c, dev_port=0, dev=6f3c9000, port_id=0, flags=0x00000410 [ 34.590000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x10008 port_id 8 [ 34.600000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 34.600000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 34.600000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 34.610000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 34.610000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 34.620000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 4 [ 34.620000] [cbm] { do_port_setting : 3260 }allocate [ 34.630000] [cbm] { do_port_setting : 3264 }cbm port 4 [ 34.630000] [cbm] { set_wlan_ep : 2938 }set elan ep 8 4 [ 34.640000] [cbm] { cbm_add_to_list : 244 }pmac 8 [ 34.640000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 32 port 4 sch_id 16 [ 34.650000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 34.660000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 34.660000] [cbm] { cbm_dp_port_alloc : 3549 }port id 8 [ 34.670000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x200 port_id 0 [ 34.670000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 34.680000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 34.680000] [cbm] { cbm_dp_port_alloc : 3446 }port id 10 [ 34.690000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 20 [ 34.690000] [cbm] { cbm_delete_from_list : 402 }cbm_delete_from_list: flags 0x200 pmac 3000 [ 34.700000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 34.710000] [cbm] { cbm_dp_port_alloc : 3522 }disabling q 29 port 20 sch_id 13 [ 34.720000] [cbm] { cbm_dp_port_alloc : 3542 }first time LOOKUP prgrm [ 34.720000] [cbm] { cbm_dp_port_alloc : 3544 }1024 [ 34.730000] [cbm] { cbm_dp_port_alloc : 3549 }port id 10 [ 34.730000] [cbm] { cbm_dp_enable : 3855 }******************ep=10 tmu_port=20 queue=29 sid=13 [ 34.740000] [cbm] { cbm_dp_enable : 3886 }enable queue 29 [ 34.740000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 34.750000] DC DP [dc_dp_alloc_port:272] Success, returned port_id=8. [ 34.760000] [4294940772] mtlk0(mtlk_df_dcdp_datapath_dev_register:11536): Registering DirectConnect dev_port 1 [ 34.770000] DC DP [dc_dp_alloc_port:182] owner=6b72816c, dev_port=1, dev=6c607000, port_id=8, flags=0x00000610 [ 34.780000] [cbm] { cbm_dp_port_alloc : 3388 }flags 0x10008 port_id 9 [ 34.790000] [cbm] { cbm_dp_port_alloc : 3400 }1 [ 34.790000] [cbm] { cbm_dp_port_alloc : 3408 }2 [ 34.800000] [cbm] { cbm_dp_port_alloc : 3427 }3 [ 34.800000] [cbm] { cbm_dp_port_alloc : 3430 }4 [ 34.800000] [cbm] { cbm_dp_port_alloc : 3435 }5 [ 34.810000] [cbm] { cbm_dp_port_alloc : 3475 }before port setting 4 [ 34.810000] [cbm] { cbm_add_to_list : 244 }pmac 9 [ 34.820000] [cbm] { cbm_dp_port_alloc : 3549 }port id 9 [ 34.820000] DC DP [dc_dp_alloc_port:272] Success, returned port_id=9. [ 34.830000] [4294940779] mtlk0(mtlk_df_dcdp_datapath_dev_register:11685): Registering network device wlan0 in DirectConnect... [ 34.840000] DC DP [dc_dp_register_dev:300] owner=6b72816c, port_id=8, dev=6f3c9000, datapathcb=6b7246f0, resources=6c7210ec, devspec=6c720fdc, flags=0x00001000 [ 34.860000] DC DP [xrx500_dcmode0_register_dev_ex:1320] dev_ctx= (null), owner=6b72816c, port_id=8, dev=6f3c9000, datapathcb=6b7246f0, resources=6c7210ec, dev_spec=6c720fdc, flags=0x00001000 [ 34.870000] DC DP [xrx500_setup_umt_port:995] Configuring UMT HW. [ 34.880000] DC DP [xrx500_setup_pmac_port:414] PMAC_EG_CFG_SET for GSW-R. [ 34.890000] DC DP [xrx500_setup_pmac_port:446] PMAC_IG_CFG_SET for GSW-R. [ 34.890000] DC DP [xrx500_setup_pmac_port:521] GSW PMAC Init Done. [ 34.900000] DC DP [xrx500_dcmode0_register_dev_ex:1426] Configuring DMA1-Tx channel 0x1000007. [ 34.910000] DC DP [xrx500_alloc_ring_buffers:554] Allocating 1 DMA1-Tx buffer lists. [ 34.920000] DC DP [xrx500_alloc_ring_buffers:569] allocating pool 1 of size 4096 KB. [ 34.920000] DC DP [xrx500_prepare_channel:634] Preparing channel 2. [ 34.930000] DC DP [xrx500_prepare_channel:696] Prepared channel 2. [ 34.940000] DC DP [xrx500_prepare_channel:634] Preparing channel 4. [ 34.940000] DC DP [xrx500_prepare_channel:696] Prepared channel 4. [ 34.950000] DC DP [dc_dp_register_dev:416] Returned 0. [ 34.950000] [4294940791] mtlk0(mtlk_df_dcdp_datapath_dev_register:11708): Registering network device wlan2 in DirectConnect... [ 34.970000] DC DP [dc_dp_register_dev:300] owner=6b72816c, port_id=9, dev=6c607000, datapathcb=6b7246f0, resources=6c7210ec, devspec=6c721004, flags=0x00001200 [ 34.980000] DC DP [xrx500_dcmode0_register_dev_ex:1320] dev_ctx= (null), owner=6b72816c, port_id=9, dev=6c607000, datapathcb=6b7246f0, resources=6c7210ec, dev_spec=6c721004, flags=0x00001200 [ 35.000000] DC DP [dc_dp_register_dev:416] Returned 0. [ 35.000000] [4294940796] mtlk0(mtlk_df_dcdp_datapath_dev_register:11745): DirectConnect accel type:2, ring type:2 --> GRX350/550 FastPath [ 35.010000] [4294940797] mtlk0(mtlk_df_dcdp_datapath_dev_register:11781): Network device wlan0 registered in DirectConnect [ 35.020000] [4294940798] mtlk0(mtlk_df_dcdp_datapath_dev_register:11783): Network device wlan2 registered in DirectConnect [ 35.040000] [4294940800] mtlk0(_mtlk_mmb_data_path_init:7720): card_idx:0, DP_port_id:8, ep3Msb:4 [ 35.050000] [4294940801] mtlk0(_mtlk_mmb_data_path_init:7739): DCDP: setup HW_MODE0 rings [ 35.050000] [4294940801] mtlk0(_mtlk_mmb_data_path_init:7824): wlan0: Initializing data path (card_idx:0, rtlog max_nof_streams:1, logger_sid:255) [ 35.070000] [4294940803] mtlk0(_mtlk_mmb_send_hw_dep_cfg:4345): XTAL value 0x6F, AFE values: 0x00000000, 0x00000000 [ 35.070000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 35.070000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 35.070000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 35.070000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 35.070000] p2p channel already ON ! [ 35.070000] phy init already done ! [ 35.070000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 35.070000] device eth0_2 entered promiscuous mode [ 35.070000] [cbm] { cbm_dp_enable : 3855 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 35.070000] [cbm] { cbm_dp_enable : 3886 }enable queue 19 [ 35.070000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 35.070000] p2p channel already ON ! [ 35.070000] phy init already done ! [ 35.070000] IPv6: ADDRCONF(NETDEV_UP): eth0_3: link is not ready [ 35.070000] device eth0_3 entered promiscuous mode [ 35.070000] [cbm] { cbm_dp_enable : 3855 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 35.070000] [cbm] { cbm_dp_enable : 3886 }enable queue 20 [ 35.070000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 35.070000] p2p channel already ON ! [ 35.070000] phy init already done ! [ 35.070000] IPv6: ADDRCONF(NETDEV_UP): eth0_4: link is not ready [ 35.070000] device eth0_4 entered promiscuous mode [ 35.200000] [4294940816] mtlk0(_mtlk_hw_mhi_stats_init:6218): u32StatisticsDataSize: 0xE12C (57644) [ 35.200000] [cbm] { cbm_dp_enable : 3855 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 35.200000] [cbm] { cbm_dp_enable : 3886 }enable queue 28 [ 35.200000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 35.200000] p2p channel already ON ! [ 35.200000] phy init already done ! [ 35.200000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 35.240000] [4294940820] mtlk0(_mtlk_hw_mhi_stats_init:6229): u32StatisticsTableSize: 0x0750 (1872) [ 35.250000] [4294940821] mtlk0(_mtlk_hw_mhi_stats_init:6268): CID-00: MHI statistics data: size 57644, buffer 0x67480000, dma_addr 0x27480000, buff_copy 0x6c790000 [ 35.260000] [4294940822] mtlk0(_mtlk_hw_mhi_get_table:5981): CID-00: MHI statistics table: size 1872, buffer 0x6ed75000, phys_addr 0x2ED75000 [ 35.280000] [4294940824] mtlk0(_hw_init_phy_rx_status:6411): PhyRxStatus: max_sid 254, all_sta_sid 511 [ 35.290000] [4294940825] mtlk0(_hw_init_phy_rx_status:6417): PhyRxStatus buffer 0x67456000, dma_addr 0x27456000, size 6184 [ 35.300000] [4294940826] mtlk0(mtlk_core_set_net_state:758): wlan0: Going from NET_STATE_HALTED to NET_STATE_IDLE [ 35.320000] [4294940828] mtlk0(_core_cfg_store_country_code:1276): CID-0000: Country Code set to: "US" [ 35.330000] [4294940829] mtlk0(_mtlk_dut_core_irbd_register:698): CID-0000: Register DUT IRBD... [ 35.340000] [4294940830] mtlk0(mtlk_core_set_net_state:758): wlan0: Going from NET_STATE_IDLE to NET_STATE_READY [ 35.350000] [4294940831] mtlk0(_mtlk_df_user_priv_subxface_start:1493): wlan0: Register DirectConnect subinterface (port_id=8, vap_id=0) [ 35.360000] DC DP [dc_dp_register_subif:430] owner=6b72816c, dev=6f3c9000, subif_id=6b4976a0, flags=0x00000000 [ 35.370000] DC DP [xrx500_dcmode0_register_subif:1485] dev_ctx=6e7fd028, owner=6b72816c, dev=6f3c9000, subif_id=6b4976a0, flags=0x00000000 [ 35.390000] DC DP [xrx500_dcmode0_register_subif:1584] Enabling UMT HW. [ 35.390000] [cbm] { cbm_dp_enable : 3855 }******************ep=8 tmu_port=4 queue=32 sid=16 [ 35.400000] [cbm] { cbm_dp_enable : 3886 }enable queue 32 [ 35.400000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 35.410000] DC DP [xrx500_dcmode0_register_subif:1647] Returned 0. [ 35.420000] DC DP [dc_dp_register_subif:525] Success, returned 0. [ 35.420000] [4294940838] mtlk0(_mtlk_df_user_priv_subxface_start:1510): wlan0: DirectConnect subinterface is registered (port_id=8, vap_id=0) [ 35.440000] [4294940840] mtlk0(mtlk_df_user_group_init:10715): wlan0: multicast callback registered [ 35.450000] [4294940841] mtlk0(mtlk_core_set_net_state:758): wlan2: Going from NET_STATE_HALTED to NET_STATE_IDLE [ 35.460000] [4294940842] mtlk0(_core_cfg_store_country_code:1276): CID-0100: Country Code set to: "US" [ 35.470000] [4294940843] mtlk0(_mtlk_dut_core_irbd_register:698): CID-0100: Register DUT IRBD... [ 35.480000] [4294940844] mtlk0(mtlk_core_set_net_state:758): wlan2: Going from NET_STATE_IDLE to NET_STATE_READY [ 35.500000] [4294940846] mtlk0(_mtlk_df_user_priv_subxface_start:1493): wlan2: Register DirectConnect subinterface (port_id=9, vap_id=0) [ 35.510000] DC DP [dc_dp_register_subif:430] owner=6b72816c, dev=6c607000, subif_id=6b4fa6a0, flags=0x00000000 [ 35.520000] DC DP [xrx500_dcmode0_register_subif:1485] dev_ctx=6e7fd33c, owner=6b72816c, dev=6c607000, subif_id=6b4fa6a0, flags=0x00000000 [ 35.530000] DC DP [xrx500_dcmode0_register_subif:1647] Returned 0. [ 35.530000] DC DP [dc_dp_register_subif:525] Success, returned 0. [ 35.540000] [4294940850] mtlk0(_mtlk_df_user_priv_subxface_start:1510): wlan2: DirectConnect subinterface is registered (port_id=9, vap_id=0) [ 35.550000] [4294940851] mtlk0(mtlk_df_user_group_init:10715): wlan2: multicast callback registered [ 35.560000] [4294940852] mtlk0(wave_radio_calibrate:5151): Processing radio_idx 0 [ 35.570000] [4294940853] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Common.bin') is starting [ 35.600000] [4294940856] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Tx.bin') is starting [ 35.610000] [4294940857] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Rx.bin') is starting [ 35.650000] [4294940861] mtlk0(prepare_progmodel_string:3958): CID-0000: ProgModel: ProgModel_gen6_Common.bin version 20327 [ 35.650000] [ 35.670000] [4294940863] mtlk0(mtlk_hw_send_cal_rfic_data:12053): RFIC calibration data missing [ 35.670000] [4294940863] mtlk0(_wave_radio_hdk_config_send:4652): band=1, offline_algo_mask=0xffffffff, online_algo_mask=0xffffffff [ 35.690000] [4294940865] mtlkE(_wave_radio_hdk_config_send:4678): dump of HDK_CONFIG_REQ [ 35.690000] [4294940865] mtlkE(_wave_radio_hdk_config_send:4678): cp= 0x6b4a8fac l=24 [ 35.700000] [4294940866] mtlkE(_wave_radio_hdk_config_send:4678): 0000: 00 00 46 27 00 00 00 00 02 02 00 06 00 00 01 00 [ 35.710000] [4294940867] mtlkE(_wave_radio_hdk_config_send:4678): 0010: ff ff ff ff ff ff ff ff [ 35.740000] [4294940870] mtlk0(wave_radio_calibrate:5164): Pre-calibration for radio_idx 0 succeeded [ 35.740000] [4294940870] mtlk0(wave_radio_calibrate:5151): Processing radio_idx 1 [ 35.750000] [4294940871] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Common.bin') is starting [ 35.760000] [4294940872] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Tx.bin') is starting [ 35.770000] [4294940873] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Rx.bin') is starting [ 35.790000] [4294940875] mtlk0(prepare_progmodel_string:3958): CID-0000: ProgModel: ProgModel_gen6_Common.bin version 20327 [ 35.790000] [ 35.800000] [4294940876] mtlk0(mtlk_hw_send_cal_rfic_data:12053): RFIC calibration data missing [ 35.810000] [4294940877] mtlk0(_wave_radio_hdk_config_send:4652): band=0, offline_algo_mask=0xffffffff, online_algo_mask=0xffffffff [ 35.820000] [4294940878] mtlkE(_wave_radio_hdk_config_send:4678): dump of HDK_CONFIG_REQ [ 35.830000] [4294940879] mtlkE(_wave_radio_hdk_config_send:4678): cp= 0x6b4a8fac l=24 [ 35.840000] [4294940880] mtlkE(_wave_radio_hdk_config_send:4678): 0000: 00 00 46 27 00 00 00 00 02 02 00 06 00 00 00 00 [ 35.850000] [4294940881] mtlkE(_wave_radio_hdk_config_send:4678): 0010: ff ff ff ff ff ff ff ff [ 35.870000] [4294940883] mtlk0(wave_radio_calibrate:5164): Pre-calibration for radio_idx 1 succeeded [ 35.880000] [4294940884] mtlk0(_wave_radio_dummy_vap_add:4808): Mac addr for calibration VAP is AC:9A:96:F1:BB:20 [ 35.940000] [4294940890] mtlk0(_wave_radio_2G_calibrate:5008): 20Mhz channels [ 36.480000] [cbm] { cbm_dp_enable : 3855 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 36.480000] [cbm] { cbm_dp_enable : 3886 }enable queue 28 [ 36.490000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 36.500000] [cbm] { cbm_dp_enable : 3855 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 36.500000] [cbm] { cbm_dp_enable : 3886 }enable queue 28 [ 36.510000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 36.510000] p2p channel already ON ! [ 36.520000] phy init already done ! [ 36.520000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 36.800000] [4294940976] mtlk0(_wave_radio_2G_calibrate:5024): 40Mhz channels [ 37.330000] [4294941029] mtlk0(_wave_radio_dummy_vap_del:4869): VAP is removed (status 0), result 0 [ 37.340000] [4294941030] mtlk0(wave_radio_calibrate:5183): Calibration for radio_idx 0 succeeded [ 37.350000] [4294941031] mtlk0(_wave_radio_dummy_vap_add:4808): Mac addr for calibration VAP is AC:9A:96:F1:BB:21 [ 37.360000] [4294941032] mtlk0(_wave_radio_5G_calibrate:5047): 20Mhz channels [ 38.890000] [4294941185] mtlk0(_wave_radio_5G_calibrate:5063): 40Mhz channels [ 39.590000] [4294941255] mtlk0(_wave_radio_5G_calibrate:5079): 80Mhz channels [ 39.950000] [4294941291] mtlk0(_wave_radio_5G_calibrate:5095): 160Mhz channels [ 40.070000] [4294941303] mtlk0(_wave_radio_dummy_vap_del:4869): VAP is removed (status 0), result 0 [ 40.080000] [4294941304] mtlk0(wave_radio_calibrate:5183): Calibration for radio_idx 1 succeeded [ 40.090000] [4294941305] mtlk0(wv_ieee80211_setup_register:2190): Registering mac80211 HW [ 40.100000] [4294941306] mtlk0(wv_cfg80211_init_band:1804): 2.4 GHz band supported, up to 2 spatial streams [ 40.110000] [4294941307] mtlk0(_core_cfg_store_country_code:1276): CID-0000: Country Code set to: "00" [ 40.120000] [4294941308] mtlk0(wv_ieee80211_setup_register:2190): Registering mac80211 HW [ 40.130000] [4294941309] mtlk0(wv_cfg80211_init_band:1804): 5 GHz band supported, up to 2 spatial streams [ 40.140000] [4294941310] mtlk0(_core_cfg_store_country_code:1276): CID-0100: Country Code set to: "00" [ 40.150000] [4294941311] mtlk0(mtlk_fast_mem_print_info:115): Using normal memory for hot context [ 40.160000] PCI: Enabling device 0000:03:00.0 (0000 -> 0002) [ 40.160000] [4294941312] mtlk0(_pci_mem_get:615): PCI Memory block 0: PA: 0xb4000000, VA: 0xf4000000, Len=0x2000000 [ 40.170000] [MTLKD] PCIE bus ChipID is:0x0000 address is:0xf4220060 [ 40.180000] [MTLKD] PCI AUX Initialization finished Wlan is running... Shutdown User APP for wlan0 try to kill hostapd_wlan0 [ get_brname][SATRT] Stop fapi_wlan_daemon (hostapd) listener Shutdown User APP for wlan2 try to kill hostapd_wlan2 [ get_brname][END] Stop fapi_wlan_daemon (hostapd) listener ### Wlan logger commands ### [ 40.860000] device wlan0 entered promiscuous mode [ 40.870000] device rtlog0 entered promiscuous mode [ 40.880000] br-lan: port 6(rtlog0) entered forwarding state [ 40.880000] br-lan: port 6(rtlog0) entered forwarding state [ 40.890000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 40.900000] device wlan2 entered promiscuous mode iw_cmd: iw wlan0 iwlwav sPowerSelection 0 iw_cmd: iw wlan0 iwlwav sCoCAutoCfg 10 50 50 50 1000 5000 5000 5000 5000 5000 iw_cmd: iw wlan0 iwlwav sScanParams 100 20 3 5 10 2 iw_cmd: iw wlan0 iwlwav sScanParamsBG 100 20 1 1 1 1000 iw_cmd: iw wlan0 iwlwav sScanModifFlags 48 iw_cmd: iw wlan0 iwlwav sScanCalCwMasks 0 0 iw_cmd: iw wlan0 iwlwav sScanExpTime 90 iw_cmd: iw wlan0 iwlwav sFWRecovery 5 3 3600 5 iw_cmd: iw wlan0 iwlwav sQAMplus 1 iw_cmd: iw wlan0 iwlwav sNumMsduInAmsdu 2 3 7 FAPI_DAEMON /opt/lantiq/wave/scripts/fapi_wlan_wave_daemon_start: Start FAPI daemon iw_cmd: iw wlan0 iwlwav sMaxMpduLen 11000 iw_cmd: iw wlan0 iwlwav sBfMode 0 iw_cmd: iw wlan0 iwlwav sInterfDetThresh -68 -68 -68 -68 5 -68 iw_cmd: iw wlan0 iwlwav sMuOperation 0 iw_cmd: iw wlan0 iwlwav sDmrConfig 0 iw_cmd: iw wlan0 iwlwav sSetRxTH -82 ### run hostapd for wlan0 ### run hostapd_wlan0 [ 42.880000] br-lan: port 6(rtlog0) entered forwarding state [ 43.800000] [4294941676] mtlk0(_mtlk_df_user_iface_open:1693): wlan0: start the interface [ 43.810000] br-lan: port 5(wlan0) entered forwarding state [ 43.810000] br-lan: port 5(wlan0) entered forwarding state [ 43.820000] cfg80211: Calling CRDA for country: DE [ 43.830000] [4294941679] mtlk0(_core_cfg_store_country_code:1276): CID-0000: Country Code set to: "DE" [ 43.850000] [4294941681] mtlk0(_core_cfg_store_country_code:1276): CID-0100: Country Code set to: "DE" [ 43.880000] [4294941684] mtlk0(_core_cfg_store_country_code:1276): CID-0000: Country Code set to: "DE" [ 43.890000] cfg80211: Regulatory domain changed to country: DE [ 43.890000] cfg80211: DFS Master region ETSI [ 43.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 43.900000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 43.910000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2300 mBm) [ 43.920000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm) [ 43.930000] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 3000 mBm) [ 43.930000] cfg80211: (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 43.940000] [4294941690] mtlk0(_scan_do_scan:1367): wlan0: Beginning scan, requester_vap_index=0 [ 43.960000] [4294941692] mtlk0(mtlk_core_set_net_state:758): wlan0: Going from NET_STATE_READY to NET_STATE_ACTIVATING [ 43.970000] [4294941693] mtlk0(mtlk_mbss_send_vap_activate:2355): CID-0000: UMI_ADD_VAP, BSSID 3C:52:A1:A9:A7:C3 [ 43.990000] [4294941695] mtlk0(_scan_do_scan:1410): radio mode 0 [ 43.990000] [4294941695] mtlk0(_mtlk_core_set_radio_mode_req:5138): CID-0000:EnableRadio FW request: Set 1 mode [ 44.010000] [4294941697] mtlk0(_scan_do_scan:1439): Scan by ap - orig_certain=0, has_stas_connected=0, do_background_scan=0 [ 44.340000] [4294941730] mtlk0(clean_up_after_this_scan:738): wlan0: Leaving the channel as uncertain after the scan [ 44.350000] [4294941731] mtlk0(scan_timeout_func:1198): wlan0: Scan done: res=0 [ 44.370000] [4294941733] mtlkE(mtlk_mmb_bss_mgmt_tx:11203): VAP not yet activated, net_state=0x8 [ 44.700000] [4294941766] mtlk0(core_cfg_set_chan_clpb:798): Notifying the kernel about the channel switch (width 40, primary at 6) [ 44.720000] [4294941768] mtlk0(_mtlk_core_activate:3513): CID-0000: open interface [ 44.730000] [4294941769] mtlk0(mtlk_core_set_net_state:758): wlan0: Going from NET_STATE_ACTIVATING to NET_STATE_CONNECTED run hostapd_cli_wlan0 ### AccessPoint post-up commands ### ACTION=change DEVICENAME=regulatory.0 hostapd for wlan0 is ready ppa_cmd: ppa dellan -i wlan0 iw_cmd: iw wlan0 iwlwav sAPforwarding 1 iw_cmd: iw wlan0 iwlwav sReliableMcast 1 iw_cmd: iw wlan0 iwlwav sBridgeMode 0 iw_cmd: iw wlan0 iwlwav sFourAddrMode 0 iw_cmd: iw wlan0 iwlwav sAggrConfig 1 1 0 iw_cmd: iw wlan0 iwlwav s11nProtection 2 /sbin/wifi:start wait for recovery event on drvhlpr wlan0 iw_cmd: iw wlan0 iwlwav sSlowProbingMask 0x3e ppa_cmd: ppa addlan -i wlan0 iw_cmd: iw wlan0 iwlwav sCoCPower 0 2 2 iw_cmd: iw wlan0 iwlwav sEnableRadio 1 iw_cmd: iw wlan0 iwlwav sTxopConfig 511 1 iw_cmd: iw wlan0 iwlwav sAcsUpdateTo 0 iw_cmd: iw wlan0 iwlwav sRTSmode 0 0 iw_cmd: iw wlan0 iwlwav sFixedRateCfg 511 1 1 1 1 7 1 iw_cmd: iw wlan0 iwlwav sInterfDetThresh -68 -68 -68 -68 5 -68 [ 45.460000] [4294941842] mtlk0(_mtlk_core_set_interfdet_do_params:7267): CID-0000: Interference detection is activated iw_cmd: iw wlan0 iwlwav sCcaAdapt 10 5 -30 10 5 30 60 iw_cmd: iw wlan0 iwlwav sFastDrop 0 iw_cmd: iw wlan0 iwlwav sFixedLtfGi 1 0 [ 45.520000] [4294941848] mtlk0(_mtlk_core_send_fixed_ltf_and_gi:4747): CID-0000: Fixed LTF and GI - isAuto:(1) ltfAndGi:(0) iw_cmd: iw wlan0 iwlwav sMuStatPlanCfg 0 32000 1 0 0 0 0 0 5400 26 2 2 2 2 2 3334 3 0 0 [ 45.540000] [MTLKD] MuStaticPlan is Off [ 45.550000] [MTLKD] Apply numOfParticipatingStations=0 due to plan is Off [ 45.550000] [4294941851] mtlk0(_mtlk_core_send_static_plan_config:2008): CID-0000: StaticPlanConfig iw_cmd: iw wlan0 iwlwav sHeMuOperation 0 iw_cmd: iw wlan0 iwlwav s11hRadarDetect 0 [ 45.590000] [4294941855] mtlk0(mtlk_log_set_conf:893): Using value of 0 for all remote debug levels, OID 8 iw_cmd: iw wlan2 iwlwav sPowerSelection 0 iw_cmd: iw wlan2 iwlwav sCoCAutoCfg 10 50 50 50 1000 5000 5000 5000 5000 5000 iw_cmd: iw wlan2 iwlwav sScanParams 100 20 3 5 10 2 iw_cmd: iw wlan2 iwlwav sScanParamsBG 100 20 1 1 1 1000 iw_cmd: iw wlan2 iwlwav sScanModifFlags 48 iw_cmd: iw wlan2 iwlwav sScanCalCwMasks 0 0 iw_cmd: iw wlan2 iwlwav sScanExpTime 90 iw_cmd: iw wlan2 iwlwav sNumMsduInAmsdu 5 3 7 iw_cmd: iw wlan2 iwlwav sMaxMpduLen 11000 iw_cmd: iw wlan2 iwlwav sBfMode 0 iw_cmd: iw wlan2 iwlwav sInterfDetThresh -68 -68 -68 -68 5 -68 iw_cmd: iw wlan2 iwlwav sMuOperation 1 iw_cmd: iw wlan2 iwlwav sDmrConfig 0 iw_cmd: iw wlan2 iwlwav sSetRxTH -82 ### run hostapd for wlan2 ### [ 45.810000] br-lan: port 5(wlan0) entered forwarding state run hostapd_wlan2 [ 46.190000] [4294941915] mtlk0(_mtlk_df_user_iface_open:1693): wlan2: start the interface [ 46.200000] br-lan: port 7(wlan2) entered forwarding state [ 46.200000] br-lan: port 7(wlan2) entered forwarding state [ 46.210000] [4294941917] mtlk0(_core_cfg_store_country_code:1276): CID-0100: Country Code set to: "DE" [ 46.230000] [4294941919] mtlk0(_scan_do_scan:1367): wlan2: Beginning scan, requester_vap_index=0 [ 46.240000] [4294941920] mtlk0(mtlk_core_set_net_state:758): wlan2: Going from NET_STATE_READY to NET_STATE_ACTIVATING [ 46.250000] [4294941921] mtlk0(mtlk_mbss_send_vap_activate:2355): CID-0100: UMI_ADD_VAP, BSSID 3C:52:A1:A9:A7:C2 [ 46.260000] [4294941922] mtlk0(_scan_do_scan:1410): radio mode 0 [ 46.270000] [4294941923] mtlk0(_mtlk_core_set_radio_mode_req:5138): CID-0100:EnableRadio FW request: Set 1 mode [ 46.280000] [4294941924] mtlk0(_scan_do_scan:1439): Scan by ap - orig_certain=0, has_stas_connected=0, do_background_scan=0 [ 46.690000] [4294941965] mtlk0(clean_up_after_this_scan:738): wlan2: Leaving the channel as uncertain after the scan [ 46.700000] [4294941966] mtlk0(scan_timeout_func:1198): wlan2: Scan done: res=0 [ 46.720000] [4294941968] mtlkE(mtlk_mmb_bss_mgmt_tx:11203): VAP not yet activated, net_state=0x8 [ 46.920000] [4294941988] mtlk0(core_cfg_set_chan_clpb:798): Notifying the kernel about the channel switch (width 80, primary at 48) [ 46.930000] [4294941989] mtlk0(_mtlk_core_activate:3513): CID-0100: open interface [ 46.940000] [4294941990] mtlk0(mtlk_core_set_net_state:758): wlan2: Going from NET_STATE_ACTIVATING to NET_STATE_CONNECTED run hostapd_cli_wlan2 ### AccessPoint post-up commands ### hostapd for wlan2 is ready ppa_cmd: ppa dellan -i wlan2 iw_cmd: iw wlan2 iwlwav sAPforwarding 1 iw_cmd: iw wlan2 iwlwav sReliableMcast 1 iw_cmd: iw wlan2 iwlwav sBridgeMode 0 iw_cmd: iw wlan2 iwlwav sFourAddrMode 0 iw_cmd: iw wlan2 iwlwav sAggrConfig 1 1 0 iw_cmd: iw wlan2 iwlwav s11nProtection 2 iw_cmd: iw wlan2 iwlwav sSlowProbingMask 0x3e ppa_cmd: ppa addlan -i wlan2 iw_cmd: iw wlan2 iwlwav sCoCPower 0 2 2 iw_cmd: iw wlan2 iwlwav sEnableRadio 1 iw_cmd: iw wlan2 iwlwav sTxopConfig 511 1 iw_cmd: iw wlan2 iwlwav sRadarRssiTh -70 iw_cmd: iw wlan2 iwlwav sAcsUpdateTo 0 /sbin/wifi:start wait for recovery event on drvhlpr wlan2 iw_cmd: iw wlan2 iwlwav sRTSmode 0 0 iw_cmd: iw wlan2 iwlwav sFixedRateCfg 511 1 2 0 1 7 1 iw_cmd: iw wlan2 iwlwav sInterfDetThresh -68 -68 -68 -68 5 -68 [ 47.760000] [4294942072] mtlk0(_mtlk_core_set_interfdet_do_params:7267): CID-0100: Interference detection is activated iw_cmd: iw wlan2 iwlwav sCcaAdapt 10 5 -30 10 5 30 60 iw_cmd: iw wlan2 iwlwav sFastDrop 0 iw_cmd: iw wlan2 iwlwav sFixedLtfGi 1 0 [ 47.810000] [4294942077] mtlk0(_mtlk_core_send_fixed_ltf_and_gi:4747): CID-0100: Fixed LTF and GI - isAuto:(1) ltfAndGi:(0) iw_cmd: iw wlan2 iwlwav sMuStatPlanCfg 0 32000 1 2 0 0 0 0 5400 26 2 2 2 2 2 3334 3 0 0 [ 47.840000] [MTLKD] MuStaticPlan is Off [ 47.840000] [MTLKD] Apply numOfParticipatingStations=0 due to plan is Off [ 47.850000] [4294942081] mtlk0(_mtlk_core_send_static_plan_config:2008): CID-0100: StaticPlanConfig iw_cmd: iw wlan2 iwlwav sHeMuOperation 0 iw_cmd: iw wlan2 iwlwav s11hRadarDetect 0 [ 47.900000] [4294942086] mtlk0(mtlk_log_set_conf:893): Using value of 0 for all remote debug levels, OID 8 [ get_brname][SATRT] [ get_brname][END] [ 48.200000] br-lan: port 7(wlan2) entered forwarding state [ 49.130000] Lan Domain: tplinklogin.net [ 49.140000] Lan Domain: www.tplinklogin.net [IPTV] WAN_PHY_IF=eth1 [IPTV] LAN_PHY_IF=eth0_4 eth0_3 eth0_2 eth0_1 [ hw_nat] Enable... BusyBox v1.19.4 (2020-07-08 13:36:20 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. MM NM MMMMMMM M M $MMMMM MMMMM MMMMMMMMMMM MMM MMM MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM' MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM MMMMMM MMMMN M MMMMMMMMM MMMM MMMM MMMM M MMMMMMM M M M --------------------------------------------------------------- For those about to rock... (Attitude Adjustment, unknown) --------------------------------------------------------------- root@Archer_AX50:/# ===>>>rftestflag=1!! Inlcuding modules needed for mwan3 ... [ 66.640000] ip_set: protocol 6 [ 67.190000] usbcore: registered new interface driver usblp usbshare boot start oldusername: admin\n oldpassword: admin\n oldusername1: visit\n oldpassword1: visit\n oldusername: admin\n oldpassword: admin\n oldusername1: visit\n oldpassword1: visit\n usbshare boot end [ 68.120000] ltq_temp: Lantiq Temperature Sensor Driver, Version 1.1.2 (c) Copyright 2014, Lantiq Deutschland GmbH [ 68.200000] ltq_pmcu: PMCU Lantiq Power Management Control Unit, Version 1.3.6 (c) Copyright 2014, Lantiq Deutschland GmbH [ 69.100000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [ 69.120000] i2c-lantiq 16a00000.i2c: timeout waiting for bus ready [LAG] Disabling bonding-lag-lan [LAG] LAG ifname is: eth0_2 eth0_1 [LAG] higherPortId = 3, lowerPortId = 2 [ 70.050000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 70.060000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 70.060000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 70.070000] br-lan: port 2(eth0_2) entered disabled state [ 70.080000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 70.090000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 70.090000] [cbm] { cbm_dp_enable : 3887 }flag 0 refcnt 1024 [ 70.100000] br-lan: port 1(eth0_1) entered disabled state [ 70.110000] bonding: bond0: Removing slave eth0_2. [ 70.120000] bonding: bond0: Error: cannot release eth0_2. [ 70.130000] [cbm] { cbm_dp_enable : 3855 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 70.140000] [cbm] { cbm_dp_enable : 3886 }enable queue 18 [ 70.140000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 70.150000] p2p channel already ON ! [ 70.150000] phy init already done ! [ 70.160000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 70.160000] bonding: bond0: Removing slave eth0_1. [ 70.170000] bonding: bond0: Error: cannot release eth0_1. [ 70.190000] [cbm] { cbm_dp_enable : 3855 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 70.200000] [cbm] { cbm_dp_enable : 3886 }enable queue 17 [ 70.200000] [cbm] { cbm_dp_enable : 3887 }flag 1 refcnt 1024 [ 70.210000] p2p channel already ON ! [ 70.210000] phy init already done ! [ 70.210000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready [ 70.230000] bonding: bond0: released all slaves General shell run! Disable lan redirect... root@Archer_AX50:/#
Yourcontent
Add your content here.
Tags
Add some basic tags, e.g. SoC, RAM, Flash. → How to add tags