MikroTik RouterBOARD RB450Gx4
The RB450Gx4 is an Ethernet router with five Gigabit Ethernet ports, a serial port, 512 MB NAND memory and a microSD card slot. In addition, it supports full 10 V - 57 V input by two power jacks or PoE (802.3af/ at or passive PoE) and can provide PoE output for Ethernet port #5. The device is powered by a quad core ARM CPU, has 1 GB of RAM and supports hardware IPsec encryption.
OpenWrt support
External image - full support.
Supporting activities
OpenWrt forum thread: https://forum.openwrt.org/t/mikrotik-rb450gx4-support/20427/15
Experimental firmware
- Heavy work in progress, however everything is functional, including SD card support.
- Native support for RouterBOOT bootloader (via an auxiliary loader).
- Prebuilt images from the experimental branch are available (LuCI included) here.
- If you need to build your own image with kernel dependencies, use the RB450Gx4-rebase-sdhci branch available at https://github.com/robimarko/openwrt.git along with with proper package snapshots from the time of the rebase.
Installation instructions
Common Procedures for Mikrotik RouterBoard Products should always be observed, as they contain general instructions for netbooting and installation, as well as reverting back to RouterOS.
1. Netboot openwrt-ipq40xx-mikrotik_rb450gx4-initramfs-fit-uImage.elf. Note that the port marked with the PoE sticker is the netboot port.
2. ubiformat the “ubi” partition
root@OpenWrt:/tmp# cat /proc/mtd dev: size erasesize name mtd0: 01000000 00040000 "kernel" mtd1: 1f000000 00040000 "ubi" mtd2: 00040000 00010000 "RouterBoot"
root@OpenWrt:/tmp# ubidetach -p /dev/mtd1 [ 152.169477] ubi0: detaching mtd1 [ 152.170618] ubi0: mtd1 is detached
root@OpenWrt:/tmp# ubiformat /dev/mtd1 -y ubiformat: mtd1 (nand), size 520093696 bytes (496.0 MiB), 1984 eraseblocks of 262144 bytes (256.0 KiB), min. I/O size 4096 bytes libscan: scanning eraseblock 1983 -- 100 % complete ubiformat: 1980 eraseblocks have valid erase counter, mean value is 1 ubiformat: 4 bad eraseblocks found, numbers: 1472, 1473, 1635, 1637 ubiformat: formatting eraseblock 1983 -- 100 % complete
3. Install openwrt-ipq40xx-mikrotik_rb450gx4-squashfs-sysupgrade.bin via sysupgrade. In case you are downloading the sysupgrade image via wget, please note that the PoE port is currently LAN1, while port 5 (the last one) is the WAN port.
root@OpenWrt:/tmp# sysupgrade -v openwrt-ipq40xx-mikrotik_rb450gx4-squashfs-sysupgrade.bin
Cannot save config while running from ramdisk.
Commencing upgrade. Closing all shell sessions.
Watchdog handover: fd=3
- watchdog -
killall: telnetd: no process killed
Sending TERM to remaining processes ... udhcpc odhcp6c ubusd logd rpcd dnsmasq netifd odhcpd uhttpd ntpd
Sending KILL to remaining processes ...
Performing system upgrade...
Unlocking kernel ...
Writing from <stdin> to kernel ...
[ 239.865007] ubi0: attaching mtd1
[ 246.475027] ubi0: scanning is finished
[ 246.500369] ubi0: attached mtd1 (name "ubi", size 496 MiB)
[ 246.500410] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 246.504757] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 246.511648] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 246.518473] ubi0: good PEBs: 1980, bad PEBs: 4, corrupted PEBs: 0
[ 246.525259] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 246.531527] ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1185731136
[ 246.538632] ubi0: available PEBs: 1940, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 36
[ 246.547930] ubi0: background thread "ubi_bgt0d" started, PID 1346
UBI device number 0, total 1980 LEBs (502824960 bytes, 479.5 MiB), available 1940 LEBs (492666880 bytes, 469.8 MiB), LEB size 253952 bytes (248.0 KiB)
Volume ID 0, size 7 LEBs (1777664 bytes, 1.6 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs", alignment 1
Set volume size to 490889216
Volume ID 1, size 1933 LEBs (490889216 bytes, 468.1 MiB), LEB size 253952 bytes (248.0 KiB), dynamic, name "rootfs_data", alignment 1
sysupgrade successful
umount: can't unmount /dev: Resource busy
umount: can't unmount /tmp: Resource busy
umount: can't unmount /: Invalid argument
4. Reboot and set RouterBOOT to boot from NAND.
Hardware highlights
| CPU | Ram | Flash | Network | WLAN | USB | Serial | JTag | SD slot |
|---|---|---|---|---|---|---|---|---|
| Qualcomm IPQ-4019 @ 716 MHz | 1024 MiB | 512 MiB | 5x 10/100/1000 | none | none | Yes | Yes | Yes |
Buttons
→ hardware.button on howto use and configure the hardware button(s).
The MikroTik RB450Gx4 has the following buttons:
| BUTTON | Event |
|---|---|
| Reset | reset |
| Reset jumper hole | not used |
The reset jumper hole is located in the corner, next to the flash chip. It is activated by closing the two sides of the hole with a metallic object (e.g. a screwdriver) and used to reset RouterBOOT to factory settings. Currently not used in OpenWrt.
LEDs
→ How to configure LEDs in general, see the LED section in the led_configuration.
The RB450Gx4 has 2 LEDs:
| LED name | LED print | Internal name |
|---|---|---|
| Power | PWR | rb450gx4:blue:power |
| User | SYS | rb450gx4:green:user |
GPIOs
The RB450Gx4 uses the following GPIO pins:
| GPIO | Common Name | Internal Name |
|---|---|---|
| 0 | Power LED (blue) | rb450gx4:blue:power |
| 2 | Buzzer | gpio-beeper |
| 3 | Green LED | rb450gx4:green:user |
| 4 | POE detect (ACTIVE_LOW) | |
| 5 | Reset | |
| 7 | Reset jumper hole | |
| 12 | Boot flash (SPI0 CS) | |
| 13 | Boot flash (SPI0) | |
| 14 | Boot flash (SPI0) | |
| 15 | Boot flash (SPI0) | |
| 16 | UART 0 | serial0 |
| 17 | UART 0 | serial0 |
| 22 | SDHC Card Detect | |
| 33 | SDHC | rb450gx4:sd:ldo |
| 33 | SDHC CS | |
| 42 | POE out | rb450gx4:poe:out |
| 53 | NAND | |
| 55 | NAND | |
| 56 | NAND | |
| 57 | NAND | |
| 58 | NAND | |
| 59 | NAND | |
| 60 | NAND | |
| 62 | NAND | |
| 63 | NAND | |
| 64 | NAND | |
| 65 | NAND | |
| 66 | NAND | |
| 67 | NAND | |
| 68 | NAND | |
| 69 | NAND |
Hardware
Info
| Architecture | ARM 32bit |
|---|---|
| Vendor | Qualcomm |
| Bootloader | RouterBOOT |
| System-On-Chip | Qualcomm IPQ4019 |
| CPU/Speed | 716 MHz |
| Flash-Chip | Hynix HY27UT084G2A |
| Flash size | 512 MiB |
| RAM | 1 GiB (Nanya NT5CC512M8DN-DI × 2) |
| Boot Flash | Winbond 25Q16JVSIM 3V 16M-bit |
| Wireless | No extension ports |
| ETH chip 1 | Qualcomm IPQ4019 |
| Switch | Atheros AR8327 |
| Ethernet | 4+1 Gbit |
| Storage | MicroSD |
| USB | None |
| Extras | Buzzer |
| Serial | Yes (Standard RS232) |
| JTAG | Not populated |
Photos
Top view
Bottom view
Opening the case
Sold without an enclosure. Form factor is identical previous RB850 and RB450 series, so the same enclosures can be used.
Serial
→ port.serial general information about the serial port, serial port cable, etc.
Standard DB9 RS232 serial connector, use a null modem cable. Parameters as follows:
| Serial connection parameters for MikroTik RB450Gx4 | 115200, 8N1 |
|---|
JTAG
JTag port is present on board, but pins are not soldered. Through-holes are drilled.
See port.jtag for more JTAG details.
Bootlogs
OEM bootlog
Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096 S - IMAGE_VARIANT_STRING=DAABANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000021 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1339 - bootable_media_detect_entry, Start B - 1679 - bootable_media_detect_success, Start B - 1692 - elf_loader_entry, Start B - 5069 - auth_hash_seg_entry, Start B - 7213 - auth_hash_seg_exit, Start B - 572244 - elf_segs_hash_verify_entry, Start B - 687732 - PBL, End B - 687757 - SBL1, Start B - 776155 - pm_device_init, Start D - 6 - pm_device_init, Delta B - 777669 - boot_flash_init, Start D - 45233 - boot_flash_init, Delta B - 827093 - boot_config_data_table_init, Start D - 3836 - boot_config_data_table_init, Delta - (419 Bytes) B - 834306 - clock_init, Start D - 7553 - clock_init, Delta B - 846381 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0 B - 849870 - sbl1_ddr_set_params, Start B - 854858 - cpr_init, Start D - 2 - cpr_init, Delta B - 859350 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13149 - sbl1_ddr_set_params, Delta B - 874424 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 942434 - sbl1_wait_for_ddr_training, Start D - 29 - sbl1_wait_for_ddr_training, Delta B - 963308 - Image Load, Start D - 140553 - QSEE Image Loaded, Delta - (262104 Bytes) B - 1104359 - Image Load, Start D - 1443 - SEC Image Loaded, Delta - (2048 Bytes) B - 1114608 - Image Load, Start D - 17194 - APPSBL Image Loaded, Delta - (30420 Bytes) B - 1132218 - QSEE Execution, Start D - 58 - QSEE Execution, Delta B - 1138362 - SBL1, End D - 452606 - SBL1, Delta S - Flash Throughput, 1854 KB/s (294991 Bytes, 159090 us) S - DDR Frequency, 672 MHz RouterBOOT booter 6.42 RB450Gx4 CPU frequency: 716 MHz Memory size: 1024 MiB NAND size: 512 MiB Press any key within 2 seconds to enter setup.. loading kernel... OK setting up elf image... OK jumping to kernel code Starting... Starting services... MikroTik 6.42.12 (long-term) MikroTik Login:
OpenWrt bootlog
RouterBOOT booter 6.44 RB450Gx4 CPU frequency: 716 MHz Memory size: 1024 MiB NAND size: 512 MiB Press any key within 2 seconds to enter setup.. loading kernel... OK setting up elf image... OK jumping to kernel code OpenWrt kernel loader for Qualcomm IPQ-4XXX/IPQ-806X Copyright (C) 2019 Sergey Sergeev <adron@mstnt.com> Extracting LZMA kernel...Done Starting kernel at 0x80208000 [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.25 (robimarko@localhost.localdomain) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9467-dd229435e0)) #0 SMP Fri Mar 1 16:43:38 2019 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Mikrotik RouterBOARD RB450Gx4 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] random: get_random_bytes called from start_kernel+0x78/0x414 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu @(ptrval) s29772 r8192 d23476 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260096 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1029680K/1046528K available (4446K kernel code, 144K rwdata, 1248K rodata, 1024K init, 228K bss, 16848K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (5439 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 145 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 229 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000021] Switching to timer-based delay loop, resolution 20ns [ 0.000251] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000269] pid_max: default: 32768 minimum: 301 [ 0.000444] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000464] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001102] CPU: Testing write buffer coherency: ok [ 0.001962] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.002104] rcu: Hierarchical SRCU implementation. [ 0.002762] smp: Bringing up secondary CPUs ... [ 0.005479] smp: Brought up 1 node, 4 CPUs [ 0.005496] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.005506] CPU: All CPU(s) started in SVC mode. [ 0.009146] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.009281] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009304] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.009500] pinctrl core: initialized pinctrl subsystem [ 0.010505] NET: Registered protocol family 16 [ 0.010754] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.011866] cpuidle: using governor ladder [ 0.011906] cpuidle: using governor menu [ 0.027133] usbcore: registered new interface driver usbfs [ 0.027204] usbcore: registered new interface driver hub [ 0.027282] usbcore: registered new device driver usb [ 0.027334] pps_core: LinuxPPS API ver. 1 registered [ 0.027343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.027369] PTP clock support registered [ 0.028552] clocksource: Switched to clocksource arch_sys_counter [ 0.029382] NET: Registered protocol family 2 [ 0.030057] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.030095] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.030195] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.030358] TCP: Hash tables configured (established 8192 bind 8192) [ 0.030490] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.030546] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.030768] NET: Registered protocol family 1 [ 0.031772] No memory allocated for crashlog [ 0.031999] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.035773] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.035787] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.040960] bounce: pool size: 64 pages [ 0.040986] io scheduler noop registered [ 0.040999] io scheduler deadline registered (default) [ 0.041777] gpio-export gpio-export: 1 gpio(s) exported [ 0.043440] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.043458] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.044645] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.044733] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 [ 0.044813] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.044890] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.045109] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.045642] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.045683] msm_serial 78af000.serial: uartclk = 1843200 [ 0.045729] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.045754] msm_serial: console setup on port #0 [ 0.566605] console [ttyMSM0] enabled [ 0.571514] msm_serial: driver initialized [ 0.578884] loop: module loaded [ 0.580192] nand: device found, Manufacturer ID: 0x98, Chip ID: 0xdc [ 0.581856] nand: Toshiba NAND 512MiB 3,3V 8-bit [ 0.588453] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 128 [ 0.593151] 2 fixed-partitions partitions found on MTD device qcom_nand.0 [ 0.600450] Creating 2 MTD partitions on "qcom_nand.0": [ 0.607388] 0x000000000000-0x000001000000 : "kernel" [ 0.627345] 0x000001000000-0x000020000000 : "ubi" [ 0.641172] random: fast init done [ 1.068223] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 1.077753] m25p80 spi0.0: w25q16jv (2048 Kbytes) [ 1.077816] 6 fixed-partitions partitions found on MTD device spi0.0 [ 1.081468] Creating 6 MTD partitions on "spi0.0": [ 1.087863] 0x000000000000-0x000000023000 : "Qualcomm-boot1" [ 1.093133] 0x000000023000-0x000000080000 : "Qualcomm-boot2" [ 1.098919] 0x000000080000-0x00000008e000 : "RouterBoot" [ 1.104483] 0x00000008e000-0x00000008f000 : "hard_config" [ 1.109802] 0x000000090000-0x0000000a0000 : "dts_config" [ 1.115084] 0x0000000bd000-0x0000000be000 : "soft_config" [ 1.121117] libphy: ipq40xx_mdio: probed [ 1.156249] ESS reset ok! [ 1.186547] ESS reset ok! [ 1.618951] libphy: Fixed MDIO Bus: probed [ 1.619846] EDMA using MAC@ - using [ 1.619861] ea:18:8c:3e:c2:90 [ 1.626123] EDMA using MAC@ - using [ 1.626134] 72:1f:98:67:71:54 [ 1.729543] i2c /dev entries driver [ 1.754942] NET: Registered protocol family 10 [ 1.756376] Segment Routing with IPv6 [ 1.758369] NET: Registered protocol family 17 [ 1.762365] 8021q: 802.1Q VLAN Support v1.8 [ 1.766375] Registering SWP/SWPB emulation handler [ 1.777153] UBI: auto-attach mtd1 [ 1.777190] ubi0: attaching mtd1 [ 3.222870] random: crng init done [ 8.006459] ubi0: scanning is finished [ 8.036164] ubi0: attached mtd1 (name "ubi", size 496 MiB) [ 8.036203] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes [ 8.040584] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 8.047410] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 8.054283] ubi0: good PEBs: 1980, bad PEBs: 4, corrupted PEBs: 0 [ 8.061050] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 8.067291] ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 388374773 [ 8.074417] ubi0: available PEBs: 0, total reserved PEBs: 1980, PEBs reserved for bad PEB handling: 36 [ 8.083376] ubi0: background thread "ubi_bgt0d" started, PID 89 [ 8.085137] block ubiblock0_0: created from ubi0:0(rootfs) [ 8.098545] ubiblock: device ubiblock0_0 (rootfs) set to be root filesyste▒[ 8.117880] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 8.119480] Freeing unused kernel memory: 1024K [ 8.149316] Run /sbin/init as init process [ 9.867099] init: Console is alive [ 9.867307] init: - watchdog - [ 10.197269] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 10.253470] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 10.269103] init: - preinit - /bin/board_detect: /etc/board.d/02_network: line 108: arithmetic syntax error [ 12.510758] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.510851] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 15.729948] UBIFS (ubi0:1): default file-system created [ 15.731356] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 196 [ 16.017161] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 16.017208] UBIFS (ubi0:1): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 16.024051] UBIFS (ubi0:1): FS size: 486572032 bytes (464 MiB, 1916 LEBs), journal size 24379392 bytes (23 MiB, 96 LEBs) [ 16.033902] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 16.044834] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID FAD72CD7-6C79-42D7-B052-21DF2525B61C, small LPT model [ 16.055619] mount_root: overlay filesystem has not been fully initialized yet [ 16.063096] mount_root: switching to ubifs overlay [ 16.080453] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 16.083436] urandom-seed: Seed file not found (/etc/urandom.seed) [ 16.181077] procd: - early - [ 16.181209] procd: - watchdog - [ 16.809722] procd: - watchdog - [ 16.812569] procd: - ubus - [ 16.976532] procd: - init - Please press Enter to activate this console. [ 17.096593] kmodloader: loading kernel modules from /etc/modules.d/* [ 17.106238] input: beeper as /devices/platform/beeper/input/input0 [ 17.119537] xt_time: kernel timezone is -0000 [ 17.130965] PPP generic driver version 2.4.2 [ 17.131931] NET: Registered protocol family 24 [ 17.141392] kmodloader: done loading kernel modules from /etc/modules.d/* [ 21.849230] br-lan: port 1(eth0) entered blocking state [ 21.849271] br-lan: port 1(eth0) entered disabled state [ 21.853638] device eth0 entered promiscuous mode [ 21.863683] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 21.878322] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 21.879910] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000 [ 21.884661] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 22.888634] br-lan: port 1(eth0) entered blocking state [ 22.888674] br-lan: port 1(eth0) entered forwarding state [ 22.894134] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.30.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r9467-dd229435e0 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#