Meraki MR42

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Describe if there are any ongoing activities that might lead to OpenWrt support.

Architecture Arm v7
Vendor Cisco Meraki
Bootloader U-Boot
System-On-Chip IPQ8068
CPU/Speed 1.4 GHz
Flash size 128 MB
RAM 512MB
Wireless 2x QCA9992, 1x QCA9889
Ethernet 1x AR8033 (PoE input)
Serial Yes - not populated
JTAG Yes - not populated
dev: size erasesize name
mtd0: 00040000 00020000 “sbl1”
mtd1: 00140000 00020000 “mibib”
mtd2: 00140000 00020000 “sbl2”
mtd3: 00280000 00020000 “sbl3”
mtd4: 00120000 00020000 “ddrconfig”
mtd5: 00120000 00020000 “ssd”
mtd6: 00280000 00020000 “tz”
mtd7: 00280000 00020000 “rpm”
mtd8: 00180000 00020000 “u-boot”
mtd9: 00a80000 00020000 “bootkernel1”
mtd10: 00a80000 00020000 “bootkernel2”
mtd11: 046c0000 00020000 “ubi”
mtd12: 00200000 00020000 “art”

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

  • Pin 1 - (has a small triangle symbol under it). Do not use.
  • Pin 2 - RX
  • Pin 3 - TX
  • Pin 4 - GND
Serial connection parameters 115200, 8N1

root@OpenWrt:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.35 (root@cluster5) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 8.4.0 r16702-9a581de63b) 8.4.0, GNU ld (GNU Binutils) 2.34) #0 SMP Tue May 11 08:53:09 2021 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Meraki MR42 [ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x44000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] On node 0 totalpages: 114432 [ 0.000000] Normal zone: 1006 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 114432 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 15 pages/cpu s30732 r8192 d22516 u61440 [ 0.000000] pcpu-alloc: s30732 r8192 d22516 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113426 [ 0.000000] Kernel command line: loader=u-boot part=bootkernel2 console=ttyMSM0,115200n8 ubi.mtd=ubi ubi.mtd=art [ 0.000000] Bootloader command line not present [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 441932K/457728K available (6552K kernel code, 608K rwdata, 1648K rodata, 1024K init, 236K bss, 15796K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x3ac/0x558 with crng_init=0 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000011] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000031] Switching to timer-based delay loop, resolution 160ns [ 0.000285] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000319] pid_max: default: 32768 minimum: 301 [ 0.000502] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000524] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001627] CPU: Testing write buffer coherency: ok [ 0.001913] qcom_scm: convention: smc legacy [ 0.002892] Setting up static identity map for 0x44300000 - 0x44300060 [ 0.003080] rcu: Hierarchical SRCU implementation. [ 0.003372] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.003619] smp: Bringing up secondary CPUs ... [ 0.005634] smp: Brought up 1 node, 2 CPUs [ 0.005656] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.005672] CPU: All CPU(s) started in SVC mode. [ 0.016516] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.016688] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016724] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.016879] pinctrl core: initialized pinctrl subsystem [ 0.018144] NET: Registered protocol family 16 [ 0.018524] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.019895] thermal_sys: Registered thermal governor 'step_wise' [ 0.022075] cpuidle: using governor ladder [ 0.022151] cpuidle: using governor menu [ 0.066116] usbcore: registered new interface driver usbfs [ 0.066203] usbcore: registered new interface driver hub [ 0.066287] usbcore: registered new device driver usb [ 0.066355] pps_core: LinuxPPS API ver. 1 registered [ 0.066373] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.066412] PTP clock support registered [ 0.066711] qcom_scm: convention: smc legacy [ 0.068680] clocksource: Switched to clocksource dg_timer [ 0.069772] NET: Registered protocol family 2 [ 0.070425] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.070484] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.070531] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.070591] TCP: Hash tables configured (established 4096 bind 4096) [ 0.070701] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.070740] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.070988] NET: Registered protocol family 1 [ 0.071043] PCI: CLS 0 bytes, default 64 [ 0.072320] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.078256] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.078281] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.184071] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator [ 0.184320] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator [ 0.184439] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator [ 0.184727] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.184763] qcom-pcie 1b500000.pci: Parsing ranges property... [ 0.184818] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fefffff -> 0x000fe00000 [ 0.184867] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000 [ 0.414627] qcom-pcie 1b500000.pci: Link up [ 0.414803] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.414833] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.414857] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.414880] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.414901] pci_bus 0000:00: scanning bus [ 0.414968] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.415127] pci 0000:00:00.0: supports D1 [ 0.415148] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.415173] pci 0000:00:00.0: PME# disabled [ 0.419256] pci_bus 0000:00: fixups for bus [ 0.419285] PCI: bus0: Fast back to back transfers disabled [ 0.419310] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.419473] pci_bus 0000:01: scanning bus [ 0.419818] pci 0000:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.420119] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.421506] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.421562] pci 0000:01:00.0: PME# disabled [ 0.425753] pci_bus 0000:01: fixups for bus [ 0.425842] PCI: bus1: Fast back to back transfers disabled [ 0.425863] pci_bus 0000:01: bus scan returning with max=01 [ 0.425885] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.425906] pci_bus 0000:00: bus scan returning with max=ff [ 0.425944] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] [ 0.425975] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.426131] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.426160] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] [ 0.426212] pci 0000:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.426418] pci 0000:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.426633] pcieport 0000:00:00.0: assign IRQ: got 42 [ 0.427417] pcieport 0000:00:00.0: AER: enabled with IRQ 43 [ 0.427530] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x10117cb) [ 0.427547] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100547) [ 0.427562] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0xff000000) [ 0.427576] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10010) [ 0.427591] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0x0) [ 0.427605] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0) [ 0.427620] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0xff0100) [ 0.427634] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0xf0) [ 0.427650] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x8100800) [ 0.427664] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x1fff1) [ 0.427678] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0) [ 0.427692] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0) [ 0.427707] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0) [ 0.427721] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x40) [ 0.427735] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0) [ 0.427750] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x3012a) [ 0.428418] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator [ 0.428681] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator [ 0.428912] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator [ 0.429202] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.429234] qcom-pcie 1b700000.pci: Parsing ranges property... [ 0.429284] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031efffff -> 0x0031e00000 [ 0.429328] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000 [ 0.655391] qcom-pcie 1b700000.pci: Link up [ 0.655557] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.655584] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.655607] pci_bus 0001:00: root bus resource [io 0x100000-0x1fffff] (bus address [0x31e00000-0x31efffff]) [ 0.655626] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.655646] pci_bus 0001:00: scanning bus [ 0.655701] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.655841] pci 0001:00:00.0: supports D1 [ 0.655860] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.655881] pci 0001:00:00.0: PME# disabled [ 0.659894] pci_bus 0001:00: fixups for bus [ 0.659920] PCI: bus0: Fast back to back transfers disabled [ 0.659942] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.660099] pci_bus 0001:01: scanning bus [ 0.660441] pci 0001:01:00.0: [168c:0040] type 00 class 0x028000 [ 0.660736] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.662116] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.662173] pci 0001:01:00.0: PME# disabled [ 0.666359] pci_bus 0001:01: fixups for bus [ 0.666447] PCI: bus1: Fast back to back transfers disabled [ 0.666466] pci_bus 0001:01: bus scan returning with max=01 [ 0.666486] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.666506] pci_bus 0001:00: bus scan returning with max=ff [ 0.666534] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.666563] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.666713] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.666739] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.666783] pci 0001:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.666988] pci 0001:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.667178] pcieport 0001:00:00.0: assign IRQ: got 44 [ 0.667832] pcieport 0001:00:00.0: AER: enabled with IRQ 45 [ 0.667950] pcieport 0001:00:00.0: saving config space at offset 0x0 (reading 0x10117cb) [ 0.667967] pcieport 0001:00:00.0: saving config space at offset 0x4 (reading 0x100547) [ 0.667983] pcieport 0001:00:00.0: saving config space at offset 0x8 (reading 0xff000000) [ 0.667998] pcieport 0001:00:00.0: saving config space at offset 0xc (reading 0x10010) [ 0.668012] pcieport 0001:00:00.0: saving config space at offset 0x10 (reading 0x0) [ 0.668026] pcieport 0001:00:00.0: saving config space at offset 0x14 (reading 0x0) [ 0.668041] pcieport 0001:00:00.0: saving config space at offset 0x18 (reading 0xff0100) [ 0.668055] pcieport 0001:00:00.0: saving config space at offset 0x1c (reading 0xf0) [ 0.668070] pcieport 0001:00:00.0: saving config space at offset 0x20 (reading 0x2e102e00) [ 0.668084] pcieport 0001:00:00.0: saving config space at offset 0x24 (reading 0x1fff1) [ 0.668098] pcieport 0001:00:00.0: saving config space at offset 0x28 (reading 0x0) [ 0.668113] pcieport 0001:00:00.0: saving config space at offset 0x2c (reading 0x0) [ 0.668127] pcieport 0001:00:00.0: saving config space at offset 0x30 (reading 0x0) [ 0.668141] pcieport 0001:00:00.0: saving config space at offset 0x34 (reading 0x40) [ 0.668156] pcieport 0001:00:00.0: saving config space at offset 0x38 (reading 0x0) [ 0.668170] pcieport 0001:00:00.0: saving config space at offset 0x3c (reading 0x3012c) [ 0.668937] qcom-pcie 1b900000.pci: supply vdda not found, using dummy regulator [ 0.669174] qcom-pcie 1b900000.pci: supply vdda_phy not found, using dummy regulator [ 0.669307] qcom-pcie 1b900000.pci: supply vdda_refclk not found, using dummy regulator [ 0.669598] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges: [ 0.669629] qcom-pcie 1b900000.pci: Parsing ranges property... [ 0.669682] qcom-pcie 1b900000.pci: IO 0x0035e00000..0x0035efffff -> 0x0035e00000 [ 0.669726] qcom-pcie 1b900000.pci: MEM 0x0032000000..0x0035dfffff -> 0x0032000000 [ 0.895409] qcom-pcie 1b900000.pci: Link up [ 0.895592] qcom-pcie 1b900000.pci: PCI host bridge to bus 0002:00 [ 0.895620] pci_bus 0002:00: root bus resource [bus 00-ff] [ 0.895642] pci_bus 0002:00: root bus resource [io 0x200000-0x2fffff] (bus address [0x35e00000-0x35efffff]) [ 0.895663] pci_bus 0002:00: root bus resource [mem 0x32000000-0x35dfffff] [ 0.895683] pci_bus 0002:00: scanning bus [ 0.895742] pci 0002:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.895891] pci 0002:00:00.0: supports D1 [ 0.895912] pci 0002:00:00.0: PME# supported from D0 D1 D3hot [ 0.895933] pci 0002:00:00.0: PME# disabled [ 0.899925] pci_bus 0002:00: fixups for bus [ 0.899951] PCI: bus0: Fast back to back transfers disabled [ 0.899975] pci 0002:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.900137] pci_bus 0002:01: scanning bus [ 0.900483] pci 0002:01:00.0: [168c:0050] type 00 class 0x028000 [ 0.900797] pci 0002:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.901298] pci 0002:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.902295] pci 0002:01:00.0: supports D1 [ 0.902314] pci 0002:01:00.0: PME# supported from D0 D1 D3hot [ 0.902371] pci 0002:01:00.0: PME# disabled [ 0.906581] pci_bus 0002:01: fixups for bus [ 0.906676] PCI: bus1: Fast back to back transfers disabled [ 0.906695] pci_bus 0002:01: bus scan returning with max=01 [ 0.906717] pci 0002:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.906737] pci_bus 0002:00: bus scan returning with max=ff [ 0.906767] pci 0002:00:00.0: BAR 8: assigned [mem 0x32000000-0x322fffff] [ 0.906797] pci 0002:01:00.0: BAR 0: assigned [mem 0x32000000-0x321fffff 64bit] [ 0.906959] pci 0002:01:00.0: BAR 6: assigned [mem 0x32200000-0x3220ffff pref] [ 0.906981] pci 0002:00:00.0: PCI bridge to [bus 01-ff] [ 0.907004] pci 0002:00:00.0: bridge window [mem 0x32000000-0x322fffff] [ 0.907051] pci 0002:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.907268] pci 0002:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.907466] pcieport 0002:00:00.0: assign IRQ: got 46 [ 0.908174] pcieport 0002:00:00.0: AER: enabled with IRQ 47 [ 0.908289] pcieport 0002:00:00.0: saving config space at offset 0x0 (reading 0x10117cb) [ 0.908306] pcieport 0002:00:00.0: saving config space at offset 0x4 (reading 0x100547) [ 0.908322] pcieport 0002:00:00.0: saving config space at offset 0x8 (reading 0xff000000) [ 0.908336] pcieport 0002:00:00.0: saving config space at offset 0xc (reading 0x10010) [ 0.908351] pcieport 0002:00:00.0: saving config space at offset 0x10 (reading 0x0) [ 0.908365] pcieport 0002:00:00.0: saving config space at offset 0x14 (reading 0x0) [ 0.908379] pcieport 0002:00:00.0: saving config space at offset 0x18 (reading 0xff0100) [ 0.908394] pcieport 0002:00:00.0: saving config space at offset 0x1c (reading 0xf0) [ 0.908408] pcieport 0002:00:00.0: saving config space at offset 0x20 (reading 0x32203200) [ 0.908424] pcieport 0002:00:00.0: saving config space at offset 0x24 (reading 0x1fff1) [ 0.908438] pcieport 0002:00:00.0: saving config space at offset 0x28 (reading 0x0) [ 0.908453] pcieport 0002:00:00.0: saving config space at offset 0x2c (reading 0x0) [ 0.908467] pcieport 0002:00:00.0: saving config space at offset 0x30 (reading 0x0) [ 0.908481] pcieport 0002:00:00.0: saving config space at offset 0x34 (reading 0x40) [ 0.908495] pcieport 0002:00:00.0: saving config space at offset 0x38 (reading 0x0) [ 0.908510] pcieport 0002:00:00.0: saving config space at offset 0x3c (reading 0x3012e) [ 0.911428] L2 @ QSB rate. Forcing new rate. [ 0.911652] L2 @ 384000 KHz [ 0.911848] CPU0 @ 800000 KHz [ 0.911866] CPU1 @ QSB rate. Forcing new rate. [ 0.912005] CPU1 @ 384000 KHz [ 0.916442] gsbi 12440000.gsbi: GSBI port protocol: 4 crci: 0 [ 0.918486] gsbi 12480000.gsbi: GSBI port protocol: 2 crci: 0 [ 0.920537] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.922611] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.923591] msm_serial 12450000.serial: msm_serial: detected port #1 [ 0.923650] msm_serial 12450000.serial: uartclk = 25000000 [ 0.923731] 12450000.serial: ttyMSM1 at MMIO 0x12450000 (irq = 48, base_baud = 1562500) is a MSM [ 0.924253] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.924305] msm_serial 16340000.serial: uartclk = 7372800 [ 0.924378] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 50, base_baud = 460800) is a MSM [ 0.924421] msm_serial: console setup on port #0 [ 2.006036] printk: console [ttyMSM0] enabled [ 2.011242] msm_serial: driver initialized [ 2.020840] loop: module loaded [ 2.022555] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xa1 [ 2.022804] nand: Macronix MX30UF1G18AC [ 2.029507] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.032967] Block protection check failed [ 2.040849] 13 fixed-partitions partitions found on MTD device qcom_nand.0 [ 2.044676] Creating 13 MTD partitions on "qcom_nand.0": [ 2.051540] 0x000000000000-0x000000040000 : "sbl1" [ 2.058012] 0x000000040000-0x000000180000 : "mibib" [ 2.064215] 0x000000180000-0x0000002c0000 : "sbl2" [ 2.069030] 0x0000002c0000-0x000000540000 : "sbl3" [ 2.071890] random: fast init done [ 2.080207] 0x000000540000-0x000000660000 : "ddrconfig" [ 2.083354] 0x000000660000-0x000000780000 : "ssd" [ 2.087400] 0x000000780000-0x000000a00000 : "tz" [ 2.095086] 0x000000a00000-0x000000c80000 : "rpm" [ 2.100822] 0x000001fc0000-0x000002140000 : "u-boot" [ 2.104544] 0x0000021c0000-0x000002c40000 : "bootkernel1" [ 2.125876] 0x000002c40000-0x0000036c0000 : "bootkernel2" [ 2.146751] 0x0000036c0000-0x000007d80000 : "ubi" [ 2.281360] 0x000007d80000-0x000007f80000 : "art" [ 2.298289] libphy: Fixed MDIO Bus: probed [ 2.300563] libphy: ipq8064_mdio_bus: probed [ 2.402071] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_wake_irq not found [ 2.402137] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_lpi not found [ 2.408620] ipq806x-gmac-dwmac 37600000.ethernet: PTP uses main clock [ 2.415742] ipq806x-gmac-dwmac 37600000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.421283] ipq806x-gmac-dwmac 37600000.ethernet: DWMAC1000 [ 2.428614] ipq806x-gmac-dwmac 37600000.ethernet: DMA HW capability register supported [ 2.434544] ipq806x-gmac-dwmac 37600000.ethernet: RX Checksum Offload Engine supported [ 2.442263] ipq806x-gmac-dwmac 37600000.ethernet: COE Type 2 [ 2.450132] ipq806x-gmac-dwmac 37600000.ethernet: TX Checksum insertion supported [ 2.455874] ipq806x-gmac-dwmac 37600000.ethernet: Wake-Up On Lan supported [ 2.463383] ipq806x-gmac-dwmac 37600000.ethernet: Enhanced/Alternate descriptors [ 2.470127] ipq806x-gmac-dwmac 37600000.ethernet: Enabled extended descriptors [ 2.477573] ipq806x-gmac-dwmac 37600000.ethernet: Ring mode enabled [ 2.484685] ipq806x-gmac-dwmac 37600000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.490883] ipq806x-gmac-dwmac 37600000.ethernet: device MAC address 76:10:28:41:e2:5b [ 2.541245] libphy: stmmac: probed [ 2.544411] i2c /dev entries driver [ 2.545153] i2c_qup 124a0000.i2c: using default clock-frequency 100000 [ 2.555313] sdhci: Secure Digital Host Controller Interface driver [ 2.555365] sdhci: Copyright(c) Pierre Ossman [ 2.560557] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.568797] NET: Registered protocol family 10 [ 2.573009] Segment Routing with IPv6 [ 2.574979] NET: Registered protocol family 17 [ 2.579199] 8021q: 802.1Q VLAN Support v1.8 [ 2.583050] Registering SWP/SWPB emulation handler [ 2.624755] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.641959] s1a: Bringing 0uV into 1050000-1050000uV [ 2.642400] s1a: supplied by regulator-dummy [ 2.646223] s1b: Bringing 0uV into 1050000-1050000uV [ 2.650749] s1b: supplied by regulator-dummy [ 2.655433] s2a: Bringing 0uV into 800000-800000uV [ 2.659927] s2a: supplied by regulator-dummy [ 2.664263] s2b: Bringing 0uV into 800000-800000uV [ 2.668840] s2b: supplied by regulator-dummy [ 2.674445] debugfs: Directory '900000.clock-controller:thermal-sensor@900000' with parent 'tsens' already present! [ 2.678966] thermal thermal_zone0: failed to read out thermal zone (-110) [ 2.689116] thermal thermal_zone6: failed to read out thermal zone (-110) [ 2.711332] ubi0: attaching mtd11 [ 2.851580] random: crng init done [ 3.348490] ubi0: scanning is finished [ 3.359927] ubi0: attached mtd11 (name "ubi", size 70 MiB) [ 3.359953] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.364299] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.371246] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.378015] ubi0: good PEBs: 566, bad PEBs: 0, corrupted PEBs: 0 [ 3.384849] ubi0: user volume: 6, internal volumes: 1, max. volumes count: 128 [ 3.391137] ubi0: max/mean erase counter: 739/395, WL threshold: 4096, image sequence number: 1331549393 [ 3.398077] ubi0: available PEBs: 0, total reserved PEBs: 566, PEBs reserved for bad PEB handling: 20 [ 3.407827] ubi1: attaching mtd12 [ 3.407984] ubi0: background thread "ubi_bgt0d" started, PID 104 [ 3.416933] ubi1: MTD device 12 is write-protected, attach in read-only mode [ 3.466977] ubi1: scanning is finished [ 3.478686] ubi1 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 2, need 20 [ 3.479620] ubi1: attached mtd12 (name "art", size 2 MiB) [ 3.487576] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.492953] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.499737] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.506500] ubi1: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 [ 3.513343] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 3.519248] ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 174698806 [ 3.526470] ubi1: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 2 [ 3.535611] ubi1: background thread "ubi_bgt1d" started, PID 105 [ 3.536705] block ubiblock0_4: created from ubi0:4(rootfs) [ 3.550783] ubiblock: device ubiblock0_4 (rootfs) set to be root filesystem [ 3.561499] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 3.562331] Freeing unused kernel memory: 1024K [ 3.589282] Run /sbin/init as init process [ 3.589304] with arguments: [ 3.589313] /sbin/init [ 3.589321] with environment: [ 3.589330] HOME=/ [ 3.589339] TERM=linux [ 3.589348] loader=u-boot [ 3.589356] part=bootkernel2 [ 4.016437] init: Console is alive [ 4.016639] init: - watchdog - [ 4.840312] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.955590] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 51 [ 4.964481] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.965886] init: - preinit - [ 6.067918] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) [ 6.069904] dwmac1000: Master AXI performs any burst length [ 6.078935] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found [ 6.084353] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 6.092617] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock [ 6.107125] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode [ 8.181811] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 8.181879] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.345431] UBIFS (ubi0:5): Mounting in unauthenticated mode [ 10.345763] UBIFS (ubi0:5): background thread "ubifs_bgt0_5" started, PID 186 [ 10.513397] UBIFS (ubi0:5): UBIFS: mounted UBI device 0, volume 5, name "rootfs_data" [ 10.513434] UBIFS (ubi0:5): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.520305] UBIFS (ubi0:5): FS size: 18411520 bytes (17 MiB, 145 LEBs), journal size 1015809 bytes (0 MiB, 7 LEBs) [ 10.530189] UBIFS (ubi0:5): reserved for root: 869621 bytes (849 KiB) [ 10.540466] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID 4E5C9C6B-679B-4AE1-A2FB-47DF8DEF9A1B, small LPT model [ 10.548362] mount_root: overlay filesystem has not been fully initialized yet [ 10.558598] mount_root: switching to ubifs overlay [ 10.929737] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.042282] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Down [ 11.103783] procd: - early - [ 11.103992] procd: - watchdog - [ 11.661461] procd: - watchdog - [ 11.662320] procd: - ubus - [ 11.785938] procd: - init - [ 12.279449] kmodloader: loading kernel modules from /etc/modules.d/* [ 12.363692] urngd: v1.0.2 started. [ 12.386150] i2c-gpio i2c-gpio0: using lines 472 (SDA) and 473 (SCL) [ 12.389064] at24 0-0056: supply vcc not found, using dummy regulator [ 12.392058] at24 0-0056: 8192 byte 24c64 EEPROM, writable, 32 bytes/write [ 12.399612] Loading modules backported from Linux version v5.10.34-0-g0aa66717f684 [ 12.404502] Backport generated by backports.git v5.10.34-1-0-g7b5533e1 [ 12.414443] ina2xx 0-0040: power monitor ina219 (Rshunt = 40000 uOhm) [ 12.429935] xt_time: kernel timezone is -0000 [ 12.557157] PPP generic driver version 2.4.2 [ 12.558095] NET: Registered protocol family 24 [ 12.582182] ath10k_pci 0000:01:00.0: assign IRQ: got 42 [ 12.582212] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x40. [ 12.582787] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 12.589186] ath10k_pci 0000:01:00.0: enabling bus mastering [ 12.589778] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 13.810043] ath10k_pci 0000:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 13.810111] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.822978] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf [ 13.927183] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 1:1 crc32 08fa09f2 [ 15.077100] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 15.077145] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 15.153395] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 15.154150] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596' [ 15.418051] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 15.511710] ath: EEPROM regdomain sanitized [ 15.511736] ath: EEPROM regdomain: 0x64 [ 15.511754] ath: EEPROM indicates we should expect a direct regpair map [ 15.511785] ath: Country alpha2 being used: 00 [ 15.511801] ath: Regpair used: 0x64 [ 15.517282] ath10k_pci 0001:01:00.0: assign IRQ: got 44 [ 15.517332] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x40. [ 15.518689] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 15.524438] ath10k_pci 0001:01:00.0: enabling bus mastering [ 15.525315] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 16.476921] ath10k_pci 0001:01:00.0: qca99x0 hw2.0 target 0x01000000 chip_id 0x003801ff sub 168c:0002 [ 16.476961] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 16.487094] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9980-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 b36a12bf [ 16.557930] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 1:2 crc32 08fa09f2 [ 17.707289] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 17.707334] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 17.784917] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 17.785642] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596' [ 18.063065] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 18.161696] ath: EEPROM regdomain sanitized [ 18.161721] ath: EEPROM regdomain: 0x64 [ 18.161739] ath: EEPROM indicates we should expect a direct regpair map [ 18.161770] ath: Country alpha2 being used: 00 [ 18.161786] ath: Regpair used: 0x64 [ 18.167247] ath10k_pci 0002:01:00.0: assign IRQ: got 46 [ 18.167300] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x50. [ 18.168745] ath10k_pci 0002:01:00.0: enabling device (0140 -> 0142) [ 18.174405] ath10k_pci 0002:01:00.0: enabling bus mastering [ 18.175159] ath10k_pci 0002:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 19.277701] ath10k_pci 0002:01:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000 [ 19.277776] ath10k_pci 0002:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 19.287865] ath10k_pci 0002:01:00.0: firmware ver 10.1-ct-87-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 61a92df5 [ 19.359883] ath10k_pci 0002:01:00.0: board_file api 1 bmi_id N/A crc32 546cca0d [ 20.226968] ath10k_pci 0002:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 20.233996] ath10k_pci 0002:01:00.0: wmi print 'P 128 V 8 T 410' [ 20.234035] ath10k_pci 0002:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 20.240062] ath10k_pci 0002:01:00.0: wmi print 'alloc rem: 25560 iram: 24780' [ 20.279738] ath10k_pci 0002:01:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 20.289053] ath10k_pci 0002:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 20.409823] ath: EEPROM regdomain sanitized [ 20.409841] ath: EEPROM regdomain: 0x64 [ 20.409851] ath: EEPROM indicates we should expect a direct regpair map [ 20.409870] ath: Country alpha2 being used: 00 [ 20.409880] ath: Regpair used: 0x64 [ 20.417144] kmodloader: done loading kernel modules from /etc/modules.d/* [ 25.445095] ipq806x-gmac-dwmac 37600000.ethernet eth0: PHY [37000000.mdio-mii:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) [ 25.446864] dwmac1000: Master AXI performs any burst length [ 25.456513] ipq806x-gmac-dwmac 37600000.ethernet eth0: No Safety Features support found [ 25.461547] ipq806x-gmac-dwmac 37600000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 25.469826] ipq806x-gmac-dwmac 37600000.ethernet eth0: registered PTP clock [ 25.478427] ipq806x-gmac-dwmac 37600000.ethernet eth0: configuring for phy/sgmii link mode [ 25.487475] br-lan: port 1(eth0) entered blocking state [ 25.494006] br-lan: port 1(eth0) entered disabled state [ 25.499439] device eth0 entered promiscuous mode [ 26.196333] ath: EEPROM regdomain: 0x824f [ 26.196358] ath: EEPROM indicates we should expect a country code [ 26.199423] ath: doing EEPROM country->regdmn map search [ 26.205413] ath: country maps to regdmn code: 0x10 [ 26.210856] ath: Country alpha2 being used: PA [ 26.215381] ath: Regpair used: 0x10 [ 26.219892] ath: regdomain 0x824f dynamically updated by user [ 26.223208] ath: EEPROM regdomain: 0x824f [ 26.229162] ath: EEPROM indicates we should expect a country code [ 26.233100] ath: doing EEPROM country->regdmn map search [ 26.239300] ath: country maps to regdmn code: 0x10 [ 26.244551] ath: Country alpha2 being used: PA [ 26.249216] ath: Regpair used: 0x10 [ 26.253570] ath: regdomain 0x824f dynamically updated by user [ 26.256985] ath: EEPROM regdomain: 0x824f [ 26.262930] ath: EEPROM indicates we should expect a country code [ 26.266854] ath: doing EEPROM country->regdmn map search [ 26.272990] ath: country maps to regdmn code: 0x10 [ 26.278310] ath: Country alpha2 being used: PA [ 26.282990] ath: Regpair used: 0x10 [ 26.287340] ath: regdomain 0x824f dynamically updated by user [ 27.700688] ipq806x-gmac-dwmac 37600000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 28.944549] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 28.944594] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 29.021881] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 29.022624] ath10k_pci 0001:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596' [ 29.403867] ath10k_pci 0001:01:00.0: rts threshold -1 [ 29.411174] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 29.412370] br-lan: port 1(eth0) entered blocking state [ 29.421231] br-lan: port 1(eth0) entered forwarding state [ 29.431757] br-lan: port 2(wlan1) entered blocking state [ 29.431814] br-lan: port 2(wlan1) entered disabled state [ 29.437715] device wlan1 entered promiscuous mode [ 29.443233] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 30.751655] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 30.751699] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 30.827801] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 30.828556] ath10k_pci 0000:01:00.0: wmi print 'free: 31080 iram: 23028 sram: 9596' [ 31.180119] ath10k_pci 0000:01:00.0: rts threshold -1 [ 31.181611] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 [ 31.191498] br-lan: port 3(wlan0) entered blocking state [ 31.195102] br-lan: port 3(wlan0) entered disabled state [ 31.200967] device wlan0 entered promiscuous mode [ 31.903038] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 31.903454] br-lan: port 2(wlan1) entered blocking state [ 31.908495] br-lan: port 2(wlan1) entered forwarding state [ 31.924332] br-lan: port 4(wlan1-1) entered blocking state [ 31.924368] br-lan: port 4(wlan1-1) entered disabled state [ 31.928946] device wlan1-1 entered promiscuous mode [ 31.939154] ath10k_pci 0001:01:00.0: rts threshold -1 [ 31.941863] br-lan: port 4(wlan1-1) entered blocking state [ 31.944168] br-lan: port 4(wlan1-1) entered forwarding state [ 32.002638] ath10k_pci 0001:01:00.0: failed to pull fw stats: -71 [ 32.034876] ath10k_pci 0001:01:00.0: wmi: fixing invalid VHT TX rate code 0xff [ 33.056739] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1-1: link becomes ready [ 33.401619] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 33.401873] br-lan: port 3(wlan0) entered blocking state [ 33.407092] br-lan: port 3(wlan0) entered forwarding state [ 33.418204] br-lan: port 5(wlan0-1) entered blocking state [ 33.418258] br-lan: port 5(wlan0-1) entered disabled state [ 33.423735] device wlan0-1 entered promiscuous mode [ 33.431703] ath10k_pci 0000:01:00.0: rts threshold -1 [ 33.439749] br-lan: port 5(wlan0-1) entered blocking state [ 33.439781] br-lan: port 5(wlan0-1) entered forwarding state [ 33.499322] ath10k_pci 0000:01:00.0: failed to pull fw stats: -71 [ 34.573680] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/05/19 19:04
  • by clayface