Qihoo 360T7 / 360T7M / 360T7U

Qihoo 360T7 / 360T7M / 360T7U is a router family around 100RMB tailored for China Telecom, CMCC and China Unicom respectively. All three models are having same hardware but different OEM firmware. As such, all information below shall apply to all three models.

None at this time.

→ Install OpenWrt (generic explanation)

Please add the installation procedure here.

Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

→ generic.flashing.tftp

Specific values needed for tftp

Bootloader tftp client IPv4 address	192.168.1.1
Firmware tftp image	Latest OpenWrt release
TFTP Server required IP address	192.168.1.254

1. Software preparation

a. Putty
b. tftpd64

STOP!

If your router is using Gigadevice 5F1GM7UE NAND (and possibly all Gigadevice NAND), DO NOT ATTEMPT to continue on this guide. Updating firmware to 360T7-v4.2.4.7959 will hardbrick your device. Instead, you need to flash u-boot and firmware with mtk_uartboot over UART.

Routers with ESMT F50L1G41LB, Winbond W25N01GV or Winbond W25N01KV NAND can ignore this warning.

2. Boot into Official firmware, update firmware using file from github. This will update the firmware to 360T7-v4.2.4.7959 in order to allow us to enter failsafe mode.

3. Attach UART (REF 2 & 3), boot the stock firmware until the message about failsafe mode appears.

NOTES ON UART: You might encounter some 360T7 fail to output messages (TX fails) after some time (can be as short as few seconds) since power on. Check resistance between TX and GND while power off and all cables detached using a multimeter. If resistance is <1K ohm, take a 5-10 min break and have a coffee. You may be able to “enjoy” few cups of coffee before successfully update the u-boot.

From experience, those routers with the above-mentioned defects will fail sooner than expected. You may try heating up the PCB using hot gun to eliminate any possible non-wetting defect, in particular area near CPU, RAM and NAND. Quality control in Qihoo is pretty much infamous.

4. Enter failsafe mode by pressing f and Enter.

5. Connect to your PC via one of the LAN port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254)

6. Start tftpd64 with the following 4 files at its root directory:

openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip
openwrt-mediatek-filogic-qihoo_360t7-initramfs-recovery.itb
openwrt-mediatek-filogic-qihoo_360t7-preloader.bin
openwrt-mediatek-filogic-qihoo_360t7-squashfs-sysupgrade.itb

7. Back up mtd partitions via tftp:

ifconfig eth0 192.168.1.1 netmask 255.255.255.0 up
for i in $(seq 1 10); do tftp -p -l /dev/mtdblock$i -r mtd${i}.bin 192.168.1.254 ; done

8. check if eeprom is at the right place. It should start with 81 79 like the following:

hexdump -C -s 1572864 -n 256 /dev/mtdblock0
00180000  81 79 00 00 00 0c 43 49  c3 57 00 00 00 00 00 00  |.y....CI.W......|
00180010  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
00180020  00 00 00 00 02 0c 43 49  c3 58 00 0c 43 49 c3 58  |......CI.X..CI.X|
00180030  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|

If it's not, you will need to flash Factory/config/factory partitions back after firmware is flashed.

9. Flash BL2 and FIP:

root@(none):/# cd /tmp
root@(none):/tmp# tftp -g -l bl2.bin -r openwrt-mediatek-filogic-qihoo_360t7-preloader.bin 192.168.1.254
root@(none):/tmp# tftp -g -l fip.fip -r openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip 192.168.1.254
root@(none):/tmp# mtd -p 0x380000 write fip.fip spi0.0
Unlocking spi0.0 ...
Seeking on mtd device 'spi0.0' to: 3670016

Writing from fip.fip to spi0.0 ...
root@(none):/tmp# mtd -r write bl2.bin spi0.0
Unlocking spi0.0 ...

Writing from bl2.bin to spi0.0 ...
Rebooting ...

10. Reset and u-boot will self-retrieve recovery file openwrt-mediatek-filogic-qihoo_360t7-initramfs-recovery.itb from TFTP Server (ip 192.168.1.254).

11. Login to http://192.168.1.1 and upload file openwrt-mediatek-filogic-qihoo_360t7-squashfs-sysupgrade.itb for sysupgrade. Please note if you are using SNAPSHOT, LuCI (Web interface) is not included. Please refer to luci.essentials on installing LuCI.

You may take reference from q30_pro. Both routers are pretty much similar.

→ generic.sysupgrade

Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
Upload image file for sysupgrade to LuCI
Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via sysupgrade. There are two command line methods for upgrading:

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

Login as root via SSH on 192.168.1.1, then enter the following commands:

cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

→ generic.debrick

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name	Description	Default configuration
br-lan	EXAMPLE LAN & WiFi	EXAMPLE 192.168.1.1/24
vlan0 (eth0.0)	EXAMPLE LAN ports (1 to 4)	EXAMPLE None
vlan1 (eth0.1)	EXAMPLE WAN port	EXAMPLE DHCP
wl0	EXAMPLE WiFi	EXAMPLE Disabled

Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port	Switch port
Internet (WAN)	EXAMPLE 4
LAN 1	EXAMPLE 3
LAN 2	EXAMPLE 2
LAN 3	EXAMPLE 1
LAN 4	EXAMPLE 0

→ hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

Please fill in real values for this device, then remove the EXAMPLEs

The Qihoo 360T7 has the following buttons:

BUTTON	Event
EXAMPLE Reset	reset
EXAMPLE Secure Easy Setup	ses
EXAMPLE No buttons at all.	-

This table is automatically generated, once the correct filters for Brand and Model are set.
If you see “Nothing.” instead of a table, please edit this section and adjust the filters with the proper Brand and Model. Just try, it's easy.
If you still don't see a table here, or a table filled with '¿': Is there already a Techdata page available for Qihoo 360T7 1.0? If not: Create one.
If you see a table with the desired device data, everything is OK and you can delete this text and the <WRAP> that encloses it.
If it still doesn't work: Don't panic, calm down, take a deep breath and contact a wiki admin (tmomas) for help.

---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=Qihoo filter : Model=360T7 filter : Versions=1.0

Front:
Insert photo of front of the casing

Back:
Insert photo of back of the casing

Backside label:
Insert photo of backside label

Note: This will void your warranty!

https://youtu.be/g9RUoa-Oyy0?si=scqyN6t8QpeNpVQj&t=77

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
https://www.right.com.cn/FORUM/thread-8278255-1-1.html

https://youtu.be/g9RUoa-Oyy0?si=Pq7worg11mbf-VZW&t=77

Serial connection parameters for Qihoo 360T7 1.0	115200, 8N1, 3.3V

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

→ bootloader

None so far.

F0: 102B 0000 FA: 1040 0000 FA: 1040 0000 [0200] F9: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [1000] T0: 0000 0256 [010F] Jump to BL NOTICE: BL2: v2.6(release):t7_4.2.3.6542_20220519-2-ga48f125a NOTICE: BL2: Built : 03:03:12, May 25 2022 NOTICE: WDT: disabled NOTICE: EMI: Using DDR3 settings dump toprgu registers data: 1001c000 | 00000000 0000ffe0 00000000 00000000 1001c010 | 00000fff 00000000 00f00000 00000000 1001c020 | 00000000 00000000 00000000 00000000 1001c030 | 003c0003 003c0003 00000000 00000000 1001c040 | 00000000 00000000 00000000 00000000 1001c050 | 00000000 00000000 00000000 00000000 1001c060 | 00000000 00000000 00000000 00000000 1001c070 | 00000000 00000000 00000000 00000000 1001c080 | 00000000 00000000 00000000 00000000 dump drm registers data: 1001d000 | 00000000 00000000 00000000 00000000 1001d010 | 00000000 00000000 00000000 00000000 1001d020 | 00000000 00000000 00000000 00000000 1001d030 | 00a083f1 000003ff 00100000 00000000 1001d040 | 00000000 00000000 00020303 000000ff 1001d050 | 00000000 00000000 00000000 00000000 1001d060 | 00000002 00000000 00000000 00000000 drm: 500 = 0x8 [DDR Reserve] ddr reserve mode not be enabled yet DDR RESERVE Success 0 [EMI] ComboMCP not ready, using default setting BYTE_swap:0 BYTE_swap:0 Window Sum 604, worse bit 5, min window 72 Window Sum 644, worse bit 8, min window 80 Window Sum 522, worse bit 6, min window 62 Window Sum 474, worse bit 11, min window 56 Window Sum 524, worse bit 1, min window 64 Window Sum 480, worse bit 15, min window 56 Window Sum 492, worse bit 15, min window 58 Window Sum 530, worse bit 0, min window 66 Window Sum 494, worse bit 9, min window 60 Window Sum 496, worse bit 9, min window 60 Window Sum 500, worse bit 8, min window 60 NOTICE: EMI: Detected DRAM size: 256MB NOTICE: EMI: complex R/W mem test passed NOTICE: CPU: MT7981 (1300MHz) NOTICE: SPI_NAND parses attributes from parameter page. NOTICE: SPI_NAND Detected ID 0xc8 NOTICE: Page size 2048, Block size 131072, size 134217728 NOTICE: Initializing NMBM ... NOTICE: Signature found at block 1023 [0x07fe0000] NOTICE: First info table with writecount 0 found in block 976 NOTICE: Second info table with writecount 0 found in block 979 NOTICE: NMBM has been successfully attached in read-only mode NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.6(release):t7_4.2.3.6542_20220519-2-ga48f125a NOTICE: BL31: Built : 03:03:16, May 25 2022 NOTICE: Hello BL31!!! U-Boot 2022.04 (May 25 2022 - 03:02:21 +0000) CPU: MediaTek MT7981 Model: mt7981-rfb DRAM: 256 MiB Core: 32 devices, 13 uclasses, devicetree: embed Initializing NMBM ... spi-nand: spi_nand spi_nand@0: GigaDevice SPI NAND was found. spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 Could not find a valid device for nmbm0 Signature found at block 1023 [0x07fe0000] First info table with writecount 0 found in block 976 Second info table with writecount 0 found in block 979 NMBM has been successfully attached Loading Environment from MTD... OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Net: Warning: ethernet@15100000 (eth0) using random MAC address - de:26:f5:cb:6c:60 eth0: ethernet@15100000 welcome to the boot loader! ubi0: attaching mtd6 ubi0: scanning is finished ubi0: attached mtd6 (name "ubi", size 36 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1658219190 ubi0: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20 Reading from volume 'kernel' to 0x46000000, size 0x326000 ... OK get_firmware_mtd_info 754 3301376 Reading from volume 'rootfs' to 0x46326000, size 0x122a000 ... OK Fit image detected... img_verify 680 3301376 ## Checking hash(es) for FIT Image at 46000000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ img_verify 690 3301376 data: 7adb9af3 18974454 1658246831 data: 7adb9af3 18974454 1658246831 ubi0: detaching mtd6 ubi0: mtd6 is detached ubi0: attaching mtd7 ubi0: scanning is finished ubi0: attached mtd7 (name "firmware-1", size 36 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1658219190 ubi0: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20 Reading from volume 'kernel' to 0x48800000, size 0x326000 ... OK get_firmware_mtd_info 754 3301376 Reading from volume 'rootfs' to 0x48b26000, size 0x122a000 ... OK Fit image detected... img_verify 680 3301376 ## Checking hash(es) for FIT Image at 48800000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ img_verify 690 3301376 data: 7adb9af3 18974454 1658246831 data: 7adb9af3 18974454 1658246831 flash offset:580000 2980000 Image1 time:1658246831 is OK. Image2 time:1658246831 is OK ## Loading kernel from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-5.4.188 Type: Kernel Image Compression: lzma compressed Data Start: 0x46000130 Data Size: 3159735 Bytes = 3 MiB Architecture: AArch64 OS: Linux Load Address: 0x48080000 Entry Point: 0x48080000 Hash algo: crc32 Hash value: a32453c8 Hash algo: sha1 Hash value: e60f07acd2182fbb6f1fcaecd264d7d42e67c4ca Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt mt7981-spim-nand-rfb device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x4630392c Data Size: 18208 Bytes = 17.8 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 75111b35 Hash algo: sha1 Hash value: 240753b4bc52f2e282e8c3f84745a533dbedba6b Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x4630392c Uncompressing Kernel Image Loading Device Tree to 000000004f7f1000, end 000000004f7f871f ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.4.188+ (root@9dee51984c13) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16304-f1f304940b)) #0 SMP Tue Jul 19 08:26:30 2022 [ 0.000000] Machine model: MediaTek MT7981 RFB [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] On node 0 totalpages: 64592 [ 0.000000] DMA32 zone: 1024 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 64592 pages, LIFO batch:15 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 20 pages/cpu s43800 r8192 d29928 u81920 [ 0.000000] pcpu-alloc: s43800 r8192 d29928 u81920 alloc=20*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 63568 [ 0.000000] Kernel command line: mtdparts=nmbm_spim_nand:1024k(bl2),512k(u-boot-env),2048k(Factory),2048k(fip),36M(ubi),36M(firmware-1),36M(plugin),1M(config),512k(factory),7M(log) console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 230816K/258368K available (6526K kernel code, 442K rwdata, 1832K rodata, 448K init, 647K bss, 27552K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x420 with crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000003] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.008182] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=52000) [ 0.018501] pid_max: default: 32768 minimum: 301 [ 0.023221] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.030482] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.039040] ASID allocator initialised with 65536 entries [ 0.044541] rcu: Hierarchical SRCU implementation. [ 0.049638] smp: Bringing up secondary CPUs ... [ 0.054486] Detected VIPT I-cache on CPU1 [ 0.054506] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.054528] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.054591] smp: Brought up 1 node, 2 CPUs [ 0.076205] SMP: Total of 2 processors activated. [ 0.080931] CPU features: detected: 32-bit EL0 Support [ 0.086093] CPU features: detected: CRC32 instructions [ 0.091362] CPU: All CPU(s) started at EL2 [ 0.095484] alternatives: patching kernel code [ 0.102254] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.112066] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.118965] pinctrl core: initialized pinctrl subsystem [ 0.124746] NET: Registered protocol family 16 [ 0.129435] DMA: preallocated 256 KiB pool for atomic allocations [ 0.149362] SCSI subsystem initialized [ 0.153294] libata version 3.00 loaded. [ 0.158019] rbus 18000000.wbsys: PCI host bridge to bus 0000:00 [ 0.164017] pci_bus 0000:00: root bus resource [mem 0x18000000-0x18ffffff] [ 0.170937] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.176451] pci_bus 0000:00: scanning bus [ 0.180492] pci 0000:00:00.0: [14c3:7981] type 00 class 0x000280 [ 0.186538] pci 0000:00:00.0: reg 0x10: [mem 0x18000000-0x1800000f 64bit] [ 0.193361] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0000000f] [ 0.199659] pci 0000:00:00.0: reg 0x1c: [mem 0x00000000-0x0000000f] [ 0.205957] pci 0000:00:00.0: reg 0x20: [mem 0x00000000-0x0000000f] [ 0.212255] pci 0000:00:00.0: reg 0x24: [mem 0x00000000-0x0000000f] [ 0.219490] pci_bus 0000:00: fixups for bus [ 0.223698] pci_bus 0000:00: bus scan returning with max=00 [ 0.230202] clocksource: Switched to clocksource arch_sys_counter [ 0.236919] thermal_sys: Registered thermal governor 'fair_share' [ 0.236922] thermal_sys: Registered thermal governor 'bang_bang' [ 0.243062] thermal_sys: Registered thermal governor 'step_wise' [ 0.249099] thermal_sys: Registered thermal governor 'user_space' [ 0.255134] thermal_sys: Registered thermal governor 'power_allocator' [ 0.261488] NET: Registered protocol family 2 [ 0.272497] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.280012] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.288420] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.296221] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.303414] TCP: Hash tables configured (established 2048 bind 2048) [ 0.309858] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.316428] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.323509] NET: Registered protocol family 1 [ 0.327908] PCI: CLS 0 bytes, default 64 [ 0.332652] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.342048] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.347936] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.371050] phy phy-usb-phy@11e10000.1: type_sw - reg 0x218, index 0 [ 0.386713] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.393814] printk: console [ttyS0] disabled [ 0.418223] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 12, base_baud = 2500000) is a ST16650V2 [ 0.427434] printk: console [ttyS0] enabled [ 0.427434] printk: console [ttyS0] enabled [ 0.435793] printk: bootconsole [uart8250] disabled [ 0.435793] printk: bootconsole [uart8250] disabled [ 0.446267] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.454686] loop: module loaded [ 0.457943] mediatek,mt2701-ice_debug ice_debug: get dbg_sel clock fail: -2 [ 0.464918] mediatek,mt2701-ice_debug: probe of ice_debug failed with error -2 [ 0.473016] mt7981-pinctrl 11d00000.pinctrl: pin_config_set op failed for pin 19 [ 0.480413] mtk-spi 1100a000.spi: Error applying setting, reverse things back [ 0.488105] spi-nand spi0.0: GigaDevice SPI NAND was found. [ 0.493688] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.504090] [mtk_hw_init] reset_lock:0, force:0 [ 0.508751] [mtk_hw_init] execute fe cold reset [ 0.524537] mtk_soc_eth 15100000.ethernet: generated random MAC address 4e:64:f5:39:5b:bf [ 0.532996] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc011680000, irq 75 [ 0.542073] mtk_soc_eth 15100000.ethernet: generated random MAC address 12:84:f7:17:fd:18 [ 0.550513] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc011680000, irq 75 [ 0.559560] (unnamed net_device) (dummy): netif_napi_add() called with weight 256 [ 0.567306] i2c /dev entries driver [ 0.571733] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 0.579723] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 0.590115] igd_filter_switch 0 [ 0.593819] NET: Registered protocol family 10 [ 0.598914] Segment Routing with IPv6 [ 0.602771] NET: Registered protocol family 17 [ 0.607253] Bridge firewalling registered [ 0.611354] 8021q: 802.1Q VLAN Support v1.8 [ 0.624708] nmbm nmbm_spim_nand: Signature found at block 1023 [0x07fe0000] [ 0.632550] nmbm nmbm_spim_nand: First info table with writecount 0 found in block 976 [ 0.642991] nmbm nmbm_spim_nand: Second info table with writecount 0 found in block 979 [ 0.651002] nmbm nmbm_spim_nand: NMBM has been successfully attached [ 0.657442] 10 cmdlinepart partitions found on MTD device nmbm_spim_nand [ 0.664132] Creating 10 MTD partitions on "nmbm_spim_nand": [ 0.669698] 0x000000000000-0x000000100000 : "bl2" [ 0.674990] 0x000000100000-0x000000180000 : "u-boot-env" [ 0.680846] 0x000000180000-0x000000380000 : "Factory" [ 0.686468] 0x000000380000-0x000000580000 : "fip" [ 0.691736] 0x000000580000-0x000002980000 : "ubi" [ 0.697060] 0x000002980000-0x000004d80000 : "firmware-1" [ 0.702983] 0x000004d80000-0x000007180000 : "plugin" [ 0.708561] 0x000007180000-0x000007280000 : "config" [ 0.714091] 0x000007280000-0x000007300000 : "factory" [ 0.719708] 0x000007300000-0x000007a00000 : "log" [ 1.286259] mt753x gsw@0: LAN/WAN VLAN setting=lllwl [ 1.291497] mt753x gsw@0: Switch is MediaTek MT7531AE rev 1 [ 1.300926] mt753x gsw@0: HWSTRAP=0xff XTAL=25MHz [ 4.947008] mt753x gsw@0: >>>>>>>>>>>>>>>>>>>>>>>>>>>>> START CALIBRATION: [ 4.954989] mt753x gsw@0: -------- gephy-calbration (port:0) -------- [ 4.970195] CALDLY = 40 [ 5.055223] 0x1e-e0 = 2d2d [ 5.059620] 0x1f-115 = 5 [ 5.062140] GE Rext AnaCal Done! (13)(0x2d) [ 5.144525] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 5.217762] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 5.291003] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 5.368793] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 5.376644] GE 1e_174(0xa4a6), 1e_175(0xa6a4) [ 5.418469] GE Tx offset AnaCal Done! (pair-0)(3)(0x22) 0x1e_172=0x2220 [ 5.447896] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x2222 [ 5.472764] GE Tx offset AnaCal Done! (pair-2)(2)(0x2) 0x1e_173=0x220 [ 5.502016] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x203 [ 5.576499] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6419) [ 5.665429] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2222) [ 5.729494] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1d25) [ 5.770908] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1a22) [ 5.817617] PORT 0 RX_DC_OFFSET [ 5.830284] before pairA output = b [ 5.835542] after pairA output = 0 [ 5.840637] before pairB output = 1e [ 5.845986] after pairB output = 0 [ 5.851081] before pairC output = 1d [ 5.856431] after pairC output = ff [ 5.861613] before pairD output = 1d [ 5.866962] after pairD output = fe [ 5.870699] mt753x gsw@0: -------- gephy-calbration (port:1) -------- [ 5.885901] CALDLY = 40 [ 5.966250] GE R50 AnaCal Done! (15) (0x23)(0xa3) [ 6.044042] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.117279] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 6.195066] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.202917] GE 1e_174(0xa3a4), 1e_175(0xa6a4) [ 6.240185] GE Tx offset AnaCal Done! (pair-0)(2)(0x21) 0x1e_172=0x2120 [ 6.274165] GE Tx offset AnaCal Done! (pair-1)(4)(0x23) 0x1e_172=0x2123 [ 6.299036] GE Tx offset AnaCal Done! (pair-2)(2)(0x2) 0x1e_173=0x220 [ 6.332838] GE Tx offset AnaCal Done! (pair-3)(4)(0x23) 0x1e_173=0x223 [ 6.413067] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x4c13) [ 6.462362] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1414) [ 6.515100] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x121a) [ 6.562175] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1b23) [ 6.608881] PORT 1 RX_DC_OFFSET [ 6.621553] before pairA output = 1c [ 6.626902] after pairA output = ff [ 6.632084] before pairB output = 1e [ 6.637434] after pairB output = ff [ 6.642617] before pairC output = e [ 6.647878] after pairC output = 0 [ 6.652974] before pairD output = f [ 6.658235] after pairD output = ff [ 6.661967] mt753x gsw@0: -------- gephy-calbration (port:2) -------- [ 6.677172] CALDLY = 40 [ 6.752961] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.830752] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.908540] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.986329] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 6.994180] GE 1e_174(0xa4a4), 1e_175(0xa4a4) [ 7.054222] GE Tx offset AnaCal Done! (pair-0)(7)(0x26) 0x1e_172=0x2620 [ 7.079093] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x2621 [ 7.117623] GE Tx offset AnaCal Done! (pair-2)(5)(0x5) 0x1e_173=0x520 [ 7.146875] GE Tx offset AnaCal Done! (pair-3)(3)(0x3) 0x1e_173=0x503 [ 7.221365] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x6c1b) [ 7.276321] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1c1c) [ 7.329066] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x1d25) [ 7.381806] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x1c24) [ 7.428520] PORT 2 RX_DC_OFFSET [ 7.441187] before pairA output = 1d [ 7.446537] after pairA output = ff [ 7.451714] before pairB output = e [ 7.456976] after pairB output = fe [ 7.462159] before pairC output = 1e [ 7.467508] after pairC output = ff [ 7.472690] before pairD output = f [ 7.477953] after pairD output = ff [ 7.481690] mt753x gsw@0: -------- gephy-calbration (port:3) -------- [ 7.496894] CALDLY = 40 [ 7.590902] GE R50 AnaCal Done! (18) (0x20)(0xa0) [ 7.677803] GE R50 AnaCal Done! (16) (0x22)(0xa2) [ 7.769262] GE R50 AnaCal Done! (17) (0x21)(0xa1) [ 7.860714] GE R50 AnaCal Done! (17) (0x21)(0xa1) [ 7.868563] GE 1e_174(0xa0a2), 1e_175(0xa1a1) [ 7.905830] GE Tx offset AnaCal Done! (pair-0)(2)(0x2) 0x1e_172=0x220 [ 7.930525] GE Tx offset AnaCal Done! (pair-1)(2)(0x21) 0x1e_172=0x221 [ 7.959860] GE Tx offset AnaCal Done! (pair-2)(3)(0x3) 0x1e_173=0x320 [ 7.979999] GE Tx offset AnaCal Done! (pair-3)(1)(0x1) 0x1e_173=0x301 [ 8.094123] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x8822) [ 8.205706] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x2727) [ 8.320732] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0x2830) [ 8.447084] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x2a32) [ 8.493789] PORT 3 RX_DC_OFFSET [ 8.506456] before pairA output = f [ 8.511713] after pairA output = 0 [ 8.516809] before pairB output = f [ 8.522072] after pairB output = ff [ 8.527254] before pairC output = 1d [ 8.532602] after pairC output = fe [ 8.537785] before pairD output = 1e [ 8.543134] after pairD output = 1 [ 8.546784] mt753x gsw@0: -------- gephy-calbration (port:4) -------- [ 8.561986] CALDLY = 40 [ 8.637774] GE R50 AnaCal Done! (14) (0x24)(0xa4) [ 8.720122] GE R50 AnaCal Done! (15) (0x23)(0xa3) [ 8.793361] GE R50 AnaCal Done! (13) (0x26)(0xa6) [ 8.875704] GE R50 AnaCal Done! (15) (0x23)(0xa3) [ 8.883554] GE 1e_174(0xa4a3), 1e_175(0xa6a3) [ 8.916273] GE Tx offset AnaCal Done! (pair-0)(1)(0x1) 0x1e_172=0x120 [ 8.945526] GE Tx offset AnaCal Done! (pair-1)(3)(0x22) 0x1e_172=0x122 [ 8.974862] GE Tx offset AnaCal Done! (pair-2)(3)(0x3) 0x1e_173=0x320 [ 9.008666] GE Tx offset AnaCal Done! (pair-3)(4)(0x4) 0x1e_173=0x304 [ 9.111457] GE Tx amp AnaCal Done! (pair-0)(1e_12 = 0x4010) [ 9.155087] GE Tx amp AnaCal Done! (pair-1)(1e_17 = 0x1414) [ 9.258788] GE Tx amp AnaCal Done! (pair-2)(1e_19 = 0xa12) [ 9.305779] GE Tx amp AnaCal Done! (pair-3)(1e_21 = 0x141c) [ 9.352491] PORT 4 RX_DC_OFFSET [ 9.365157] before pairA output = e [ 9.370421] after pairA output = ff [ 9.375599] before pairB output = e [ 9.380862] after pairB output = 1 [ 9.385957] before pairC output = 1e [ 9.391310] after pairC output = ff [ 9.396492] before pairD output = 1e [ 9.401842] after pairD output = 0 [ 9.405581] mt753x gsw@0: wan link should change to down status! [ 9.413822] UBI: auto-attach mtd5 [ 9.417168] ubi0: attaching mtd5 [ 9.422256] random: fast init done [ 9.537107] ubi0: scanning is finished [ 9.545802] ubi0: attached mtd5 (name "ubi", size 36 MiB) [ 9.551206] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 9.558070] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 9.564846] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 9.571796] ubi0: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0 [ 9.577790] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 9.585000] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1658219190 [ 9.594118] ubi0: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20 [ 9.603328] ubi0: background thread "ubi_bgt0d" started, PID 676 [ 9.603976] block ubiblock0_1: created from ubi0:1(rootfs) [ 9.614823] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 9.621777] hctosys: unable to open rtc device (rtc0) [ 9.630079] VFS: Mounted root (squashfs filesystem) readonly on device 253:0. [ 9.637453] Freeing unused kernel memory: 448K [ 9.654246] Run /sbin/init as init process [ 9.897274] init: Console is alive [ 9.900824] init: - watchdog - [ 10.186038] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 10.211702] conninfra@(mtk_conninfra_drv_init:644) Before platform_driver_register [ 10.219387] Get Index(0-TOP_MISC_BASE) phy_addr(0x11d10000) vir_addr=(0xffffffc010ac1000) size=(0x1000) [ 10.228774] Get Index(1-TOPRGU_BASE) phy_addr(0x1001c000) vir_addr=(0xffffffc010ac3000) size=(0x1000) [ 10.237980] Get Index(2-GPIO_BASE) phy_addr(0x11d00000) vir_addr=(0xffffffc010ac5000) size=(0x1000) [ 10.247013] Get Index(3-IOCFG_TR_BASE) phy_addr(0x11f00000) vir_addr=(0xffffffc010acd000) size=(0x1000) [ 10.256396] Get Index(4-IOCFG_TL_BASE) phy_addr(0x11f10000) vir_addr=(0xffffffc010ad5000) size=(0x1000) [ 10.265776] Get Index(5-INFRACFG_AO_BASE) phy_addr(0x10003000) vir_addr=(0xffffffc010add000) size=(0x1000) [ 10.275416] Get Index(6-CONN_INFRA_CFG_BASE) phy_addr(0x18001000) vir_addr=(0xffffffc010ae5000) size=(0x1000) [ 10.285316] Get Index(7-CONN_INFRA_SYSRAM_BASE) phy_addr(0x18050000) vir_addr=(0xffffffc010ae7000) size=(0x1000) [ 10.295476] Get Index(8-CONN_INFRA_CLKGEN_ON_TOP_BASE) phy_addr(0x18009000) vir_addr=(0xffffffc010ae9000) size=(0x1000) [ 10.306243] Get Index(9-CONN_HOST_CSR_TOP_BASE) phy_addr(0x18060000) vir_addr=(0xffffffc010aeb000) size=(0x1000) [ 10.316403] Get Index(10-CONN_INFRA_BUS_CR_BASE) phy_addr(0x1800e000) vir_addr=(0xffffffc010aed000) size=(0x1000) [ 10.326651] Get Index(11-CONN_INFRA_RGU_BASE) phy_addr(0x18000000) vir_addr=(0xffffffc010af5000) size=(0x1000) [ 10.336637] Get Index(12-CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18005000) vir_addr=(0xffffffc010afd000) size=(0x1000) [ 10.347057] Get Index(13-INST2_CONN_WT_SLP_CTL_REG_BASE) phy_addr(0x18085000) vir_addr=(0xffffffc010aff000) size=(0x1000) [ 10.358000] Get Index(14-CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18004000) vir_addr=(0xffffffc010b01000) size=(0x1000) [ 10.368420] Get Index(15-INST2_CONN_RF_SPI_MST_REG_BASE) phy_addr(0x18084000) vir_addr=(0xffffffc010b03000) size=(0x1000) [ 10.379362] Get Index(16-CONN_SEMAPHORE_BASE) phy_addr(0x18070000) vir_addr=(0xffffffc010ba0000) size=(0x10000) [ 10.389436] Get Index(17-CONN_AFE_CTL_BASE) phy_addr(0x18003000) vir_addr=(0xffffffc010b05000) size=(0x1000) [ 10.399249] Get Index(18-CONN_AFE_CTL_2ND_BASE) phy_addr(0x18083000) vir_addr=(0xffffffc010b07000) size=(0x1000) [ 10.409411] Get Index(19-WF_TOP_SLPPROT_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010bc0000) size=(0x10000) [ 10.419744] Get Index(20-WF_TOP_CFG_BASE) phy_addr(0x184b0000) vir_addr=(0xffffffc010b09000) size=(0x1000) [ 10.429385] Get Index(21-WF_MCU_CONFIG_LS_BASE) phy_addr(0x184f0000) vir_addr=(0xffffffc010b0b000) size=(0x1000) [ 10.439544] Get Index(22-WF_MCU_BUS_CR_BASE) phy_addr(0x18400000) vir_addr=(0xffffffc010b79000) size=(0x1000) [ 10.449444] Get Index(23-WF_MCUSYS_INFRA_BUS_FULL_U_DEBUG_CTRL_AO_BASE) phy_addr(0x18500000) vir_addr=(0xffffffc010b7b000) size=(0x1000) [ 10.461688] Get Index(24-WF_TOP_CFG_ON_BASE) phy_addr(0x184c0000) vir_addr=(0xffffffc010b80000) size=(0x10000) [ 10.471673] conninfra@(consys_plt_hw_init:162) adie_cfg_type = 1, one_adie_dbdc = 1 [ 10.479322] [emi_mng_init] gConEmiPhyBase = [0x47c80000] size = [0x100000] fw size = [0x100000] ops=[(____ptrval____)] [ 10.490093] conninfra@(mtk_conninfra_drv_init:650) After platform_driver_register [ 10.497939] ConnInfra Dev: init (0) [ 10.502877] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP version successfully! (0x02090000) [ 10.512720] conninfra@(connsys_d_die_cfg:365) D-die efuse: 0x00000000 [ 10.520177] conninfra@(_connsys_a_die_cfg_7976:919) adie_idx[0], A-die CHIP ID = 0x7976, HW Version = 0x8a10 [ 10.530996] conninfra@(consys_spi_write_nolock:501) addr=0x0a00, val=0xffffffff [ 10.539299] conninfra@(consys_spi_write_nolock:501) addr=0x04ac, val=0x0000001c [ 10.547601] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002 [ 10.556911] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x00000000 [ 10.566220] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x43a60000 [ 10.579559] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b1, 0x00000000] [ 10.591072] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002 [ 10.600383] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a6003a [ 10.609694] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63a7003a [ 10.623034] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b1, 0x00000000] [ 10.634546] conninfra@(consys_spi_write_nolock:501) addr=0x0144, val=0x00000002 [ 10.643857] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x23a7003a [ 10.653165] conninfra@(consys_spi_write_nolock:501) addr=0x0148, val=0x63ac003a [ 10.666504] conninfra@(connsys_a_die_efuse_read_nolock:737) efuse = [0x00000001, 0x00c40000, 0x008800b1, 0x00000000] [ 10.678016] conninfra@(consys_spi_write_nolock:501) addr=0x0038, val=0x4a563b00 [ 10.686319] conninfra@(consys_spi_write_nolock:501) addr=0x065c, val=0x1d59080f [ 10.694620] conninfra@(consys_spi_write_nolock:501) addr=0x0664, val=0x34c00fe0 [ 10.702927] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x88888005 [ 10.712188] conninfra@(consys_spi_write_nolock:501) addr=0x0070, val=0x00000005 [ 10.720424] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP version successfully! (0x02090000) [ 10.730237] conninfra@(_consys_hw_conninfra_wakeup:470) conninfra_wakeup refcnt=[0]->[1] wakeup!! [ 10.739100] conninfra@(_consys_hw_conninfra_sleep:490) conninfra_sleep refcnt=[1]->[0] sleep!! [ 10.747699] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[0] CONNINFRA=[1] [ 10.760312] mediatek_soc_hnat 15100000.hnat: wan = eth1 [ 10.765556] mediatek_soc_hnat 15100000.hnat: lan = eth0 [ 10.770780] mediatek_soc_hnat 15100000.hnat: ppd = eth0 [ 10.775998] mediatek_soc_hnat 15100000.hnat: gmac num = 2 [ 10.781388] mediatek_soc_hnat 15100000.hnat: ppe num = 1 [ 10.787140] mediatek_soc_hnat 15100000.hnat: PPE0 entry number = 8192 [ 10.803958] mediatek_soc_hnat 15100000.hnat: PPE0 hwnat start [ 10.809742] hnat roaming work enable [ 10.816325] warp_module_init(): module init and register callback for warp [ 10.823245] create warp_ctrl ok!!! [ 10.826682] wed_get_slot_map(): assign slot_id:0 for entry: 0! [ 10.832520] wed_get_slot_map(): assign slot_id:1 for entry: 1! [ 10.838783] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 10.856328] init: - preinit - [ 11.167332] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 11.175748] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root [ 15.232512] crng init done readonly: 0 [ 15.349526] mount_root: loading kmods from internal overlay [ 15.359650] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 15.367842] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 16.440238] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 16.446087] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 770 [ 16.477460] UBIFS (ubi0:2): recovery needed [ 16.639652] UBIFS (ubi0:2): recovery completed [ 16.644193] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 16.652022] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.661933] UBIFS (ubi0:2): FS size: 9904128 bytes (9 MiB, 78 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 16.672010] UBIFS (ubi0:2): reserved for root: 467796 bytes (456 KiB) [ 16.678446] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 227FA9C5-B04B-48BB-A026-4A3D29B2FE5B, small LPT model [ 16.690089] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 16.697140] block: unable to load configuration (fstab: Entry not found) [ 16.703870] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 16.710342] block: unable to load configuration (fstab: Entry not found) [ 16.717056] block: attempting to load /etc/config/fstab [ 16.723374] block: unable to load configuration (fstab: Entry not found) [ 16.730088] block: no usable configuration [ 16.740704] UBIFS (ubi0:2): un-mount UBI device 0 [ 16.745439] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops [ 16.754351] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 16.760081] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 773 [ 16.823552] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 16.831388] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 16.841290] UBIFS (ubi0:2): FS size: 9904128 bytes (9 MiB, 78 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 16.851365] UBIFS (ubi0:2): reserved for root: 467796 bytes (456 KiB) [ 16.857797] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 227FA9C5-B04B-48BB-A026-4A3D29B2FE5B, small LPT model [ 17.847783] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 17.854836] block: unable to load configuration (fstab: Entry not found) [ 17.861566] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 17.868062] block: unable to load configuration (fstab: Entry not found) [ 17.874781] block: attempting to load /etc/config/fstab [ 17.880083] block: unable to load configuration (fstab: Entry not found) [ 17.886795] block: no usable configuration [ 17.891504] mount_root: overlay filesystem has not been fully initialized yet [ 17.898799] mount_root: switching to ubifs overlay After mount_root[ 17.908963] urandom-seed: Seed file not found (/etc/urandom.seed) readonly: 0 read usr uci from uci zone failed cp: can't stat '/tmp/usr/config/*': No such file or directory [ 18.301229] procd: - early - [ 18.304210] procd: - watchdog - [ 18.839695] procd: - watchdog - [ 18.854681] procd: - ubus - [ 18.910653] procd: - init - [ 19.197701] urngd: v1.0.2 started. [ 19.202603] kmodloader: loading kernel modules from /etc/modules.d/* [ 19.237301] Current mapfilter version v3.0.1.2 [ 20.023722] mt_wifi: module license 'Proprietary' taints kernel. [ 20.029745] Disabling lock debugging due to kernel taint [ 20.068870] conninfra@(conninfra_pwr_on:120) [conninfra_pwr_on] drv=[3] [ 20.076450] conninfra@(_consys_polling_chipid_int:306) Read CONNSYS HW IP version successfully! (0x02090000) [ 20.094309] Adie Type: 0x7976 [ 20.094311] SKU Type: 3000 [ 20.098228] conninfra@(opfunc_power_on_internal:241) [Conninfra Pwr On] BT=[0] FM=[0] GPS=[0] WF=[1] CONNINFRA=[1] [ 20.140465] WiFi@C12L1,get_dbg_setting_by_profile() 4242: debug level setting=INDEX0_debug_level not found!! [ 20.150317] WiFi@C12L1,get_dbg_setting_by_profile() 4265: debug option setting=INDEX0_debug_option not found!! [ 20.160375] mt_rbus 0000:00:00.0: runtime IRQ mapping not provided by arch [ 20.174622] mt7981_init()--> [ 20.177499] Use the default iPAiLNA bin image! [ 20.181988] <--mt7981_init() [ 20.184891] RtmpRaDevCtrlInit(): MCS_LUT not used becasue MacTb size(288) > 128! [ 20.192401] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX1 [ 20.199725] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX2 [ 20.207040] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX3 [ 20.214354] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX4 [ 20.221668] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX5 [ 20.228992] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX6 [ 20.236312] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX7 [ 20.243625] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX8 [ 20.250940] WiFi@C12L1,match_index_by_chipname() 502: not find chip name INDEX9 [ 20.258239] WiFi@C12L2,match_index_by_chipname() 507: Not find slot id, back to old rule. [ 20.266510] msta_ifname not found [ 20.277611] -->mtfwd_init(ver:2.0) [ 20.277653] <-- [ 20.281664] mtk_warp_proxy: module uses symbols from proprietary module mt_wifi, inheriting taint. [ 20.299633] xt_time: kernel timezone is -0000 [ 20.305538] PPP generic driver version 2.4.2 [ 20.310686] PPP MPPE Compression module registered [ 20.316333] NET: Registered protocol family 24 [ 20.322716] kmodloader: done loading kernel modules from /etc/modules.d/* [ 23.445495] ##igd_filter_switch:1, old:0, write1 [ 23.450183] start igd_filter by role [ 23.454728] ------------------------------------------- [ 23.459991] -----------igd fitler inited--------------- [ 23.465228] ------------------------------------------- [ 23.470449] start igd_filter by role end [ 23.710814] ubi2: attaching mtd10 [ 23.745081] ubi2: scanning is finished [ 23.754517] ubi2: attached mtd10 (name "log", size 7 MiB) [ 23.759951] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 23.766849] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 23.773642] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 23.780608] ubi2: good PEBs: 56, bad PEBs: 0, corrupted PEBs: 0 [ 23.786527] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 23.793750] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2270766128 [ 23.802884] ubi2: available PEBs: 0, total reserved PEBs: 56, PEBs reserved for bad PEB handling: 20 [ 23.812060] ubi2: background thread "ubi_bgt2d" started, PID 2345 [ 23.849453] UBIFS (ubi2:0): Mounting in unauthenticated mode [ 23.855768] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 2420 [ 23.881594] UBIFS (ubi2:0): recovery needed [ 23.945857] UBIFS (ubi2:0): recovery completed [ 23.950370] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "log" [ 23.957507] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 23.967417] UBIFS (ubi2:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 23.977495] UBIFS (ubi2:0): reserved for root: 131942 bytes (128 KiB) [ 23.983931] UBIFS (ubi2:0): media format: w5/r0 (latest is w5/r0), UUID 03196E12-2F21-4A9B-A144-47EF79E9D7F3, small LPT model [ 27.717414] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 27.798123] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 27.806669] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 27.815349] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 27.824535] device eth0 entered promiscuous mode [ 27.830760] br-lan: port 1(eth0.1) entered blocking state [ 27.836184] br-lan: port 1(eth0.1) entered disabled state [ 27.841803] device eth0.1 entered promiscuous mode [ 27.852805] br-lan: port 1(eth0.1) entered blocking state [ 27.858224] br-lan: port 1(eth0.1) entered forwarding state [ 27.868970] br-lan: port 2(eth0.2) entered blocking state [ 27.874505] br-lan: port 2(eth0.2) entered disabled state [ 27.881147] device eth0.2 entered promiscuous mode [ 27.886141] br-lan: port 2(eth0.2) entered blocking state [ 27.891565] br-lan: port 2(eth0.2) entered forwarding state [ 27.922307] br-lan: port 3(eth0.3) entered blocking state [ 27.927711] br-lan: port 3(eth0.3) entered disabled state [ 27.933518] device eth0.3 entered promiscuous mode [ 27.938504] br-lan: port 3(eth0.3) entered blocking state [ 27.943931] br-lan: port 3(eth0.3) entered forwarding state [ 27.954910] br-lan: port 4(eth1-v6) entered blocking state [ 27.960435] br-lan: port 4(eth1-v6) entered disabled state [ 27.968344] device eth1-v6 entered promiscuous mode [ 27.991996] mtk_soc_eth 15100000.ethernet eth1: configuring for fixed/2500base-x link mode [ 28.001569] device eth1 entered promiscuous mode [ 28.635502] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 28.647415] msta_ifname not found [ 28.653131] client_get_axi_slot_id(): wrong BUS_TYPE [ 28.658152] warp_cap_support(): chip_id=7981 is in WHNAT support list [ 28.664635] warp_entry_acquire(): bus slot:0, hook to WARP, entry id=0, entry: 000000008f02cfc7 [ 28.673350] client_hif_specific_get(): hw->base_phy_addr 0x18000000!! [ 28.679806] client_chip_specific_get(): 0x7981 chip id 0x7981!! [ 28.685834] warp_entry_get_by_pdev(): return entry[0] [ 28.692554] warp_msg_register():warp,pid,3761,id,0,wed_idx,0 [ 28.698317] wed_init(0): res_start = 0x15010000, size = 1000, irq=7,base_addr=0xffffffc010fc4000 [ 28.707575] wed_ring_init(): wed tx ring init result = 0 [ 28.713109] wed_ring_init(): wed rx ring init result = 0 [ 28.725575] create wed ok!!! [ 28.728551] wdma_init(): wdma(0) base_addr=0xffffffc010fc6800, base_phy_addr=0x15104800 [ 28.737395] warp_woif_bus_init_hw(): bus:00000000d7ac6cfa, txring: 20, pa: 0x000000004cd96000, 0x000000004cd96000, 24, 28, 3c [ 28.748731] warp_woif_bus_init_hw(): bus:00000000d7ac6cfa, rxring: 50, pa: 0x000000004cdcc000, 0x000000004cdcc000, 54, 58, 6c [ 28.760101] get_region_info(): wed_idx = 0, base_addr = 0x000000006da379bb, size = 0x40000, res.start = 0x47d80000, shared:0 [ 28.771364] get_region_info(): wed_idx = 0, base_addr = 0x00000000290eec41, size = 0x8000, res.start = 0x151e0000, shared:0 [ 28.782559] get_region_info(): wed_idx = 0, base_addr = 0x000000007ce6380e, size = 0x240000, res.start = 0x47dc0000, shared:1 [ 28.793903] get_region_info(): wed_idx = 0, base_addr = 0x000000009251f42a, size = 0x1000, res.start = 0x15194000, shared:0 [ 28.805051] warp_fwdl_mcu_mode(): mcu mode, need fwdl [ 28.865987] ########## WO Firmware ########## [ 28.870387] Chip ID: 0x0000 [ 28.873172] ECO version:0 [ 28.875800] Version: DEV_000000 [ 28.878943] Build date: 20220420202134 [ 28.882692] Total region:3 [ 28.885386] ################################# [ 28.889756] Parsing tailer region 0 [ 28.893258] Target address: 0x151e0000 [ 28.897115] Download size: 20736 [ 28.900466] Parsing tailer region 1 [ 28.903968] Target address: 0x47d80000 [ 28.907820] Download size: 86000 [ 28.911223] Parsing tailer region 2 [ 28.914723] Target address: 0x47dc0000 [ 28.918568] Download size: 2283984 [ 28.927703] warp_fwdl_ready_check_mcu_mode(): waiting for wocpu [ 28.945252] warp_fwdl_ready_check_mcu_mode(): wocpu is ready [ 28.952848] warp_woctrl_init_state(), wo_state: WO_STATE_ENABLE [ 28.958831] wo_proc_init done 00000000ba8288f8 [ 28.963387] wo_exep_proc_init done 00000000ba8288f8 [ 28.968395] wo_exception_init(0): exp log= 0x00000000064c35ac, phy_addr= 0x0000000045f00000 size= 32768 [ 29.086974] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS0 PhyMode=78 [ 29.093613] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS1 PhyMode=78 [ 29.100251] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS2 PhyMode=78 [ 29.106873] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS3 PhyMode=78 [ 29.113500] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS4 PhyMode=78 [ 29.120127] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS5 PhyMode=78 [ 29.126749] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS6 PhyMode=78 [ 29.133374] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS7 PhyMode=14 [ 29.139999] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS8 PhyMode=177 [ 29.146732] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS9 PhyMode=177 [ 29.153454] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS10 PhyMode=177 [ 29.160264] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS11 PhyMode=177 [ 29.167062] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS12 PhyMode=177 [ 29.173867] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS13 PhyMode=177 [ 29.180685] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS14 PhyMode=177 [ 29.187503] 7981@C12L1,RTMPWirelessModeCfg() 604: Init: BSS15 PhyMode=48 [ 29.194593] 7981@C23L3,auto_ch_select_set_cfg() 3409: BandIdx0, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 29.204203] 7981@C23L3,auto_ch_select_set_cfg() 3409: BandIdx1, AutoChannelAtBootup=1, AutoChannelAlg = 3 [ 29.293669] 7981@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=0, Desired MFPC=0 [ 29.301088] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=1, Desired MFPC=0 [ 29.308520] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=2, Desired MFPC=0 [ 29.315961] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=3, Desired MFPC=0 [ 29.323393] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=4, Desired MFPC=0 [ 29.330811] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=5, Desired MFPC=0 [ 29.338224] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=6, Desired MFPC=0 [ 29.341681] led_log: pid 3889 ppid 1 fast_config not_configed [ 29.341681] [ 29.345636] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=7, Desired MFPC=0 [ 29.360251] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=8, Desired MFPC=0 [ 29.367664] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=9, Desired MFPC=0 [ 29.375084] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=10, Desired MFPC=0 [ 29.382589] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=11, Desired MFPC=0 [ 29.390098] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=12, Desired MFPC=0 [ 29.397601] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=13, Desired MFPC=0 [ 29.405114] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=14, Desired MFPC=0 [ 29.412624] WiFi@C15L1,Set_PMFMFPC_Proc() 1722: [PMF] :: apidx=15, Desired MFPC=0 [ 29.421970] WiFi@C12L1,RTMPSetProfileParameters() 8443: ra0, QoSMgmtCapa=0 [ 29.428889] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.436056] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.443221] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.450365] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.457525] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.464684] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.471851] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.479008] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.486173] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.493327] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.500478] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.507642] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.514807] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.521982] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.529138] WiFi@C12L1,RTMPSetProfileParameters() 8443: (null), QoSMgmtCapa=0 [ 29.544877] WiFi@C12L1,rtmp_read_ap_client_from_file() 1588: APCLI[0] ApCliMuMimoDlEnable = 0 [ 29.553418] WiFi@C12L1,rtmp_read_ap_client_from_file() 1588: APCLI[1] ApCliMuMimoDlEnable = 0 [ 29.562215] WiFi@C12L1,rtmp_read_ap_client_from_file() 1607: APCLI[0] ApCliMuMimoUlEnable = 0 [ 29.570752] WiFi@C12L1,rtmp_read_ap_client_from_file() 1607: APCLI[1] ApCliMuMimoUlEnable = 0 [ 29.681306] wdma_dma_ctrl(): WDMA_GLO_CFG=50404e70, txrx = 0 [ 29.690883] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e70, txrx = 0 [ 29.706225] warp_tx_ring_init_hw(): configure ring 0 setting [ 29.711910] warp_tx_ring_init_hw(): wed:00000000a8a5a6ae wifi:000000008b43ea7d: 24420=4cd58000,24424=2048,24428=0 [ 29.722219] warp_tx_ring_init_hw(): configure ring 1 setting [ 29.727879] warp_tx_ring_init_hw(): wed:00000000a8a5a6ae wifi:000000008b43ea7d: 24430=47440000,24434=2048,24438=0 [ 29.738251] set_rrocfg,0 [ 29.769748] wdma_dma_ctrl(): WDMA_GLO_CFG=40404e74, txrx = 3 [ 29.775440] using E1 ROM patch [ 29.778508] using E1 RAM [ 29.781043] current sync CR = 0x1 [ 29.818339] Built date: 20220420201732a [ 29.822318] Platform: ALPS [ 29.825121] HW/SW version: 0x8a108a10 [ 29.825129] Patch version: 0xffffffff [ 29.836128] current sync CR = 0x1 netstat start normal set loglevel to 2 os_log_init sucess error:os_log_init:227:1os_log_init sucess warn:os_log_init:228:2os_log_init sucess Warning: no elinksn in factory partition [ 30.129805] Chip ID: 0x14 [ 30.132545] Eco version: 0x00 [ 30.135667] Region number: 0x0b [ 30.138919] Format version: 0x02 [ 30.142247] Format flag: 0x01 [ 30.145309] Ram version: ____000000 [ 30.148917] Built date: 20220420201748 [ 30.152785] Common crc: 0x29f8303a [ 30.156296] Release info: header tag = 0, total length = 64 [ 30.161980] tag 1, padding length = 1, tag length = 59 [ 30.167232] payload: t-neptune-main-mt7915-1953-MT7981_MP2111_3_0-20220420201700 [ 30.253415] Chip ID: 0x00 [ 30.256173] Eco version: 0x00 [ 30.259257] Region number: 0x03 [ 30.262499] Format version: 0x02 [ 30.265809] Format flag: 0x01 [ 30.268872] Ram version: DEV_000000 [ 30.272463] Built date: 20220420202058 [ 30.276323] Common crc: 0xf1c27858 [ 30.279820] Release info: header tag = 0, total length = 0 [ 30.364229] current sync CR = 0x7 [ 30.368176] efuse_probe: efuse = deaddead [ 30.389942] WiFi@C02L1,is_cal_free_ic() 835: [a-die version:1] netstat start normal set loglevel to 2 os_log_init sucess error:os_log_init:227:1os_log_init sucess warn:os_log_init:228:2os_log_init sucess netstat start normal set loglevel to 2 os_log_init sucess error:os_log_init:227:1os_log_init sucess warn:os_log_init:228:2os_log_init sucess timeswitch normal [ 31.580843] [HNAT] LAN IP: 192.168.2.1 LAN MASK: 255.255.255.0 [ 32.156810] sh (5524): drop_caches: 3 [ 32.494494] ubi1: attaching mtd7 [ 32.556804] ubi1: scanning is finished [ 32.560559] ubi1: empty MTD device detected [ 32.588570] ubi1: attached mtd7 (name "plugin", size 36 MiB) [ 32.594248] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 32.601121] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 32.607904] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 32.614858] ubi1: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0 [ 32.620864] ubi1: user volume: 0, internal volumes: 1, max. volumes count: 128 [ 32.628079] ubi1: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 2325026331 [ 32.637205] ubi1: available PEBs: 264, total reserved PEBs: 24, PEBs reserved for bad PEB handling: 20 [ 32.646510] ubi1: background thread "ubi_bgt1d" started, PID 5572 [ 32.754966] UBIFS (ubi1:0): default file-system created [ 32.761975] UBIFS (ubi1:0): Mounting in unauthenticated mode [ 32.767771] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 5577 [ 32.841053] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_plugin" [ 32.848803] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 32.858712] UBIFS (ubi1:0): FS size: 32251904 bytes (30 MiB, 254 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs) [ 32.869134] UBIFS (ubi1:0): reserved for root: 1523336 bytes (1487 KiB) [ 32.875745] UBIFS (ubi1:0): media format: w5/r0 (latest is w5/r0), UUID 6A47C8D1-82C1-4918-B6C5-7F4356264510, small LPT model [ 33.358143] WiFi@C17L1,RTMPReadTxPwrPerRate() 450: (450): Don't Support this now! [ 33.365713] WiFi@C01L1,AntCfgInit() 3060: Not support for HIF_MT yet! [ 33.393919] ch_switch_monitor_state_machine_init:: enter [ 33.399263] ch_switch_monitor_cfg_reset:: enter [ 33.403800] ch_switch_monitor_cfg_reset:: enter [ 33.408769] WiFi@C17L1,tx_pwr_comp_init() 641: NotSupportYet! [ 33.414800] WiFi@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 33.420339] WiFi@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 33.426043] WiFi@C14L1,IPMacTable_init() 348: IPMacTable already inited! [ 33.452946] wdma_dma_ctrl(): WDMA_GLO_CFG=58404e75, txrx = 3 [ 33.458983] WiFi@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 33.464645] WiFi@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 33.470172] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.480089] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13431: DAT config band(0) cck_timeout Fail! [ 33.488796] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.498727] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13442: DAT config band(0) ofdm_timeout Fail! [ 33.507508] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.517421] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13453: DAT config band(0) ofdma_timeout Fail! [ 33.526304] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.536223] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13431: DAT config band(1) cck_timeout Fail! [ 33.544935] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.554852] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13442: DAT config band(1) ofdm_timeout Fail! [ 33.563636] WiFi@C00L1,set_ack_timeout_mode_byband() 13343: CTS/ACK Timeout Range should between [0xFFFF:0]!! [ 33.573554] WiFi@C00L1,set_datcfg_ack_cts_timeout() 13453: DAT config band(1) ofdma_timeout Fail! [ 33.598341] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 33.607102] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 33.742592] :(op = 1) [ 33.749705] 7981@C00L1,FastPathCheckMIC() 1010: (ret = 0)(op:1) [ 33.755668] 7981@C00L2,red_tail_drop_init() 83: red_tail_drop_init: available token:8192, whnat_en:1 [ 33.764824] 7981@C00L1,MtCmdCr4RedSet() 914: MtCmdCr4RedSet: (ret = 0) [ 33.771361] 7981@C00L1,SendRedCmd() 1049: SendRedCmd:(ret = 1) [ 33.777292] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 33.785307] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 0 [ 33.790898] 7981@C18L3,BuildChannelList() 475: [ 33.795469] 7981@C00L3,BuildChannelList() 505: BandIdx = 0, PhyMode = 78, ChListNum = 13: [ 33.803653] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.810006] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.816460] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.822826] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.829266] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.835630] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.842069] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.848429] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.854872] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.861226] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.867670] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.874023] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.880471] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.886826] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.893265] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.899623] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.906062] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.912418] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.918868] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.925270] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.931715] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.938074] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.944515] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.950873] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.957316] 7981@C14L1,vht80_channel_group() 1560: invalid ch_band 0 [ 33.963673] 7981@C14L1,vht160_channel_group() 1629: invalid ch_band 0 [ 33.970113] 7981@C23L1,DfsBuildChannelList() 3487: [RDM]: wdev is not 5G. [ 33.976924] 7981@C23L3,RadarStateCheck() 239: Zero Wait State: 0 [ 33.982933] phy_freq_adjust : no prim_ch value for adjust! [ 33.988424] 7981@C23L1,operate_loader_phy() 375: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 34.001852] wdev_attr_update(): wdevId0 = e0:ef:02:63:71:22 [ 34.007463] WiFi@C12L1,wifi_sys_open() 891: wifi_sys_open():band0 group_idx[0]=0, bw_grp=16 omac=0 [ 34.020033] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=0 [ 34.026480] 7981@C23L1,HcGetBandByChannel() 1104: No hdev parking on channel:0, just return a default band_idx 0! [ 34.036860] 7981@C02L2,AsicRadioOnOffCtrl() 2291: DbdcIdx=0 RadioOn [ 34.043877] 7981@C00L2,ApAutoChannelAtBootUp() 338: -----------------> [ 34.050429] 7981@C00L3,ApAutoChannelAtBootUp() 349: [QIHOO]OriChannel 0 [ 34.057522] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 34.063107] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 34.068721] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=1, ctrl_ch2=0, cent_ch=1 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 34.454499] 7981@C23L2,UpdateChannelInfo() 240: channel 1 busytime 10871 [ 34.461389] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=2, ctrl_ch2=0, cent_ch=2 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 34.838666] 7981@C23L2,UpdateChannelInfo() 240: channel 2 busytime 4679 [ 34.845434] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=3, ctrl_ch2=0, cent_ch=3 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 35.242574] 7981@C23L2,UpdateChannelInfo() 240: channel 3 busytime 5708 [ 35.249344] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=4, ctrl_ch2=0, cent_ch=4 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 35.638539] 7981@C23L2,UpdateChannelInfo() 240: channel 4 busytime 1042 [ 35.645366] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=5, ctrl_ch2=0, cent_ch=5 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 36.034530] 7981@C23L2,UpdateChannelInfo() 240: channel 5 busytime 2185 [ 36.041296] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=6, ctrl_ch2=0, cent_ch=6 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) iptv start normal [ 36.418577] 7981@C23L2,UpdateChannelInfo() 240: channel 6 busytime 7225 [ 36.425381] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=7, ctrl_ch2=0, cent_ch=7 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 36.490756] led_log: pid 6819 ppid 1 role_type [ 36.490756] [ 36.802552] 7981@C23L2,UpdateChannelInfo() 240: channel 7 busytime 5153 [ 36.809346] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=8, ctrl_ch2=0, cent_ch=8 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 37.186524] 7981@C23L2,UpdateChannelInfo() 240: channel 8 busytime 3782 [ 37.193287] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=9, ctrl_ch2=0, cent_ch=9 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 37.409414] led_log: pid 7379 ppid 5992 role_type unknown [ 37.409414] [ 37.418271] led_log: pid 7389 ppid 5992 wifi_result unknown [ 37.418271] [ 37.570544] 7981@C23L2,UpdateChannelInfo() 240: channel 9 busytime 1438 [ 37.577392] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=10, ctrl_ch2=0, cent_ch=10 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 37.954524] 7981@C23L2,UpdateChannelInfo() 240: channel 10 busytime 6380 [ 37.961377] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=11, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 38.338538] 7981@C23L2,UpdateChannelInfo() 240: channel 11 busytime 6072 [ 38.345388] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=12, ctrl_ch2=0, cent_ch=12 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 38.722547] 7981@C23L2,UpdateChannelInfo() 240: channel 12 busytime 3228 [ 38.729416] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=13, ctrl_ch2=0, cent_ch=13 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(1) [ 39.110555] 7981@C23L2,UpdateChannelInfo() 240: channel 13 busytime 2697 [ 39.117320] 7981@C23L2,select_clear_channel_busy_time() 1808: ===================================================== [ 39.128113] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 1 : Busy Time = 10871, Score 90,Skip Channel = FALSE [ 39.139219] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.149680] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 2 : Busy Time = 15550, Score 85,Skip Channel = FALSE [ 39.160738] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.171205] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 3 : Busy Time = 16579, Score 84,Skip Channel = FALSE [ 39.182259] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.192708] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 4 : Busy Time = 11913, Score 89,Skip Channel = FALSE [ 39.203765] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.214223] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 5 : Busy Time = 13056, Score 87,Skip Channel = FALSE [ 39.225281] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.235739] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 6 : Busy Time = 7225, Score 93,Skip Channel = FALSE [ 39.246716] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.257167] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 7 : Busy Time = 16024, Score 84,Skip Channel = FALSE [ 39.268229] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.278683] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 8 : Busy Time = 14653, Score 86,Skip Channel = FALSE [ 39.289748] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.300196] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 9 : Busy Time = 12309, Score 88,Skip Channel = FALSE [ 39.311245] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.321696] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 10 : Busy Time = 17251, Score 83,Skip Channel = FALSE [ 39.332843] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.343282] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 11 : Busy Time = 6072, Score 94,Skip Channel = FALSE [ 39.354330] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.364774] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 12 : Busy Time = 14099, Score 86,Skip Channel = TRUE [ 39.375827] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.386263] 7981@C23L2,select_clear_channel_busy_time() 1814: Channel 13 : Busy Time = 13568, Score 87,Skip Channel = TRUE [ 39.397316] 7981@C23L2,select_clear_channel_busy_time() 1815: ===================================================== [ 39.407764] 7981@C23L2,select_clear_channel_busy_time() 1823: =============== select best ch for 2.4G ============= [ 39.418224] 7981@C23L3,Adj_ZeroWait_Status_Update() 1005: ch=11 [ 39.424329] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=11, ctrl_ch2=0, cent_ch=11 DBDCIdx=0, ChBand=0, BW=0, TXStream=2, RXStream=2, scan(0) [ 39.465763] led_log: pid 8523 ppid 5992 role_type unknown [ 39.465763] [ 39.474628] led_log: pid 8524 ppid 5992 wifi_result unknown [ 39.474628] [ 39.568532] 7981@C23L1,DfsBuildChannelList() 3487: [RDM]: wdev is not 5G. [ 39.575399] 7981@C23L3,zero_wait_dfs_switch_ch() 925: outband ch 0, ch_stat 0 [ 39.582758] 7981@C08L2,APStartUpForMbss() 993: ===>(caller:ap_inf_open+0x138/0x4b8 [mt_wifi]), mbss_idx:0, CfgMode:0 [ 39.593320] 7981@C15L2,APPMFInit() 133: [PMF] apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 39.600733] 7981@C18L3,BuildChannelList() 475: [ 39.605583] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 39.613235] WiFi@C08L2,ap_link_up() 7068: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(0) [ 39.621885] 7981@C01L3,wifi_sys_linkup() 1150: wdev idx = 0 [ 39.697648] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=0 [ 39.708787] 7981@C08L3,UpdateBeaconHandler() 1935: BCN_UPDATE_INIT, OmacIdx = 0 (ra0) [ 39.716697] 7981@C08L3,UpdateBeaconHandler() 1948: Band0 BcnInitedRnd = 53 [ 39.724088] 7981@C00L1,TxCCKStreamCtrl() 20588: set wrong parameters [ 39.740673] PrintSrCmd: [ 39.740673] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.740673] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 39.754747] PrintSrCmd: [ 39.754747] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.754747] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 39.768822] PrintSrCmd: [ 39.768822] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.768822] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 39.782845] PrintSrCmd: [ 39.782845] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.782845] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 39.797005] PrintSrCmd: [ 39.797005] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.797005] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 39.811151] PrintSrCmd: [ 39.811151] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 39.811151] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 39.825302] 7981@C03L3,MtCmdTxPwrShowInfo() 13711: ucTxPowerInfoCatg: 2, BandIdx: 0 [ 39.833093] 7981@C03L3,MtCmdTxPwrShowInfo() 13740: (ret = 0) [ 39.833204] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0 [ 39.838772] mtk_ppe_dev_register_hook : ineterface ra0 register (1) [ 39.855577] nf_unregister_hooks() [ 39.861561] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 39.873161] br-lan: port 5(ra0) entered blocking state [ 39.878361] br-lan: port 5(ra0) entered disabled state [ 39.883727] device ra0 entered promiscuous mode [ 39.888318] br-lan: port 5(ra0) entered blocking state [ 39.893461] br-lan: port 5(ra0) entered forwarding state [ 39.899803] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 39.915765] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 39.963321] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 39.971971] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 39.984401] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 40.012423] 7981@C08L2,mbss_virtual_if_open() 134: ===> ra4 [ 40.018115] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 40.026271] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 40.034382] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 4 [ 40.040005] 7981@C18L3,BuildChannelList() 475: [ 40.044837] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 40.052868] wdev_attr_update(): wdevId4 = e2:ef:02:43:71:22 [ 40.058541] WiFi@C12L1,wifi_sys_open() 891: wifi_sys_open():band0 group_idx[4]=9, bw_grp=16 omac=17 [ 40.070699] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=4 [ 40.079356] 7981@C02L2,AsicRadioOnOffCtrl() 2291: DbdcIdx=0 RadioOn [ 40.109755] 7981@C00L2,ApAutoChannelAtBootUp() 338: -----------------> [ 40.116353] 7981@C00L3,ApAutoChannelAtBootUp() 349: [QIHOO]OriChannel 11 [ 40.123280] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 40.128956] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 40.134422] 7981@C00L1,ApAutoChannelAtBootUp() 508: not A band [ 40.140306] 7981@C08L1,ap_run_at_boot() 641: ACS is disable !! [ 40.147215] 7981@C08L2,APStartUpForMbss() 993: ===>(caller:ap_inf_open+0x138/0x4b8 [mt_wifi]), mbss_idx:4, CfgMode:0 [ 40.157781] 7981@C15L2,APPMFInit() 133: [PMF] apidx=4, MFPC=0, MFPR=0, SHA256=0 [ 40.165159] 7981@C18L3,BuildChannelList() 475: [ 40.170025] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 40.177684] WiFi@C08L2,ap_link_up() 7068: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(4) [ 40.186325] 7981@C01L3,wifi_sys_linkup() 1150: wdev idx = 4 [ 40.270166] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=4 [ 40.281108] 7981@C08L3,UpdateBeaconHandler() 1935: BCN_UPDATE_INIT, OmacIdx = 11 (ra4) [ 40.289460] 7981@C00L1,TxCCKStreamCtrl() 20588: set wrong parameters [ 40.305938] PrintSrCmd: [ 40.305938] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.305938] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 40.320008] PrintSrCmd: [ 40.320008] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.320008] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 40.334060] PrintSrCmd: [ 40.334060] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.334060] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 40.348109] PrintSrCmd: [ 40.348109] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.348109] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 40.362239] PrintSrCmd: [ 40.362239] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.362239] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 40.376386] PrintSrCmd: [ 40.376386] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 0, u1Status = 0 [ 40.376386] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 40.390527] 7981@C03L3,MtCmdTxPwrShowInfo() 13711: ucTxPowerInfoCatg: 2, BandIdx: 0 [ 40.398323] 7981@C03L3,MtCmdTxPwrShowInfo() 13740: (ret = 0) [ 40.398430] [mtf_txpower_all_rate_info] band_idx:0 pwr:48 ChBand:2G ePAGain:0 [ 40.404006] mtk_ppe_dev_register_hook : ineterface ra4 register (2) [ 40.420976] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 40.429035] OUI length is 0, DEL_OUI_Filter delete all and return!! [ 40.436461] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 40.445779] OUI length is 0, OID_DEL_PROBERSP_VENDOR_IE delete all and return!! [ 40.453572] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 40.490348] br-lan: port 6(ra4) entered blocking state [ 40.495530] br-lan: port 6(ra4) entered disabled state [ 40.500953] device ra4 entered promiscuous mode [ 40.505682] br-lan: port 6(ra4) entered blocking state [ 40.510848] br-lan: port 6(ra4) entered forwarding state [ 40.523287] module exit [ 40.532727] 7981@C08L2,mbss_virtual_if_open() 134: ===> rai0 [ 40.538526] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 40.546654] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 40.554690] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 8 [ 40.560284] 7981@C18L3,BuildChannelList() 475: [ 40.564867] 7981@C00L3,BuildChannelList() 505: BandIdx = 1, PhyMode = 177, ChListNum = 13: [ 40.573198] 7981@C23L3,DfsBuildChannelList() 3532: Done [ 40.578470] 7981@C23L3,RadarStateCheck() 239: Zero Wait State: 0 [ 40.584501] 7981@C23L3,RadarStateCheck() 285: RD_NORMAL_MODE [ 40.591301] phy_freq_adjust : no prim_ch value for adjust! [ 40.596801] 7981@C23L1,operate_loader_phy() 375: phy_freq_adjust failed!WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 40.610239] wdev_attr_update(): wdevId8 = e0:ef:02:63:71:23 [ 40.615871] WiFi@C12L1,wifi_sys_open() 891: wifi_sys_open():band1 group_idx[8]=4, bw_grp=16 omac=0 [ 40.624985] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=8 [ 40.632600] 7981@C23L1,HcGetBandByChannel() 1104: No hdev parking on channel:0, just return a default band_idx 0! [ 40.643153] 7981@C02L2,AsicRadioOnOffCtrl() 2291: DbdcIdx=0 RadioOn [ 40.650153] 7981@C00L2,ApAutoChannelAtBootUp() 338: -----------------> [ 40.656730] 7981@C00L3,ApAutoChannelAtBootUp() 349: [QIHOO]OriChannel 0 [ 40.663624] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 40.669223] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 40.674680] 7981@C23L2,AutoChSelBuildChannelListFor56G() 2709: ChListNum56G = 13 [ 40.682331] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=36, ctrl_ch2=0, cent_ch=36 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 41.178533] 7981@C23L2,UpdateChannelInfo() 240: channel 36 busytime 3086 [ 41.185413] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=40, ctrl_ch2=0, cent_ch=40 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 41.520311] led_log: pid 9485 ppid 5992 role_type unknown [ 41.520311] [ 41.528894] led_log: pid 9495 ppid 5992 wifi_result unknown [ 41.528894] [ 41.690664] 7981@C23L2,UpdateChannelInfo() 240: channel 40 busytime 4077 [ 41.697604] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=44, ctrl_ch2=0, cent_ch=44 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 42.206611] 7981@C23L2,UpdateChannelInfo() 240: channel 44 busytime 1921 [ 42.213517] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=48, ctrl_ch2=0, cent_ch=48 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 42.714480] 7981@C23L2,UpdateChannelInfo() 240: channel 48 busytime 3922 [ 42.721323] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=52, ctrl_ch2=0, cent_ch=52 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 43.034471] 7981@C23L2,UpdateChannelInfo() 240: channel 52 busytime 4346 [ 43.041260] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=56, ctrl_ch2=0, cent_ch=56 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 43.354452] 7981@C23L2,UpdateChannelInfo() 240: channel 56 busytime 6026 [ 43.361243] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=60, ctrl_ch2=0, cent_ch=60 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 43.569322] led_log: pid 9950 ppid 5992 role_type unknown [ 43.569322] [ 43.577703] led_log: pid 9951 ppid 5992 wifi_result unknown [ 43.577703] [ 43.674453] 7981@C23L2,UpdateChannelInfo() 240: channel 60 busytime 3460 [ 43.681242] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=64, ctrl_ch2=0, cent_ch=64 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 43.994451] 7981@C23L2,UpdateChannelInfo() 240: channel 64 busytime 3662 [ 44.001239] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=149, ctrl_ch2=0, cent_ch=149 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 44.502452] 7981@C23L2,UpdateChannelInfo() 240: channel 149 busytime 134 [ 44.509237] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=153, ctrl_ch2=0, cent_ch=153 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 45.002454] 7981@C23L2,UpdateChannelInfo() 240: channel 153 busytime 453 [ 45.009242] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=157, ctrl_ch2=0, cent_ch=157 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 45.510448] 7981@C23L2,UpdateChannelInfo() 240: channel 157 busytime 0 [ 45.517057] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=161, ctrl_ch2=0, cent_ch=161 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 45.617904] led_log: pid 9956 ppid 5992 role_type unknown [ 45.617904] [ 45.626412] led_log: pid 9957 ppid 5992 wifi_result unknown [ 45.626412] [ 46.022463] 7981@C23L2,UpdateChannelInfo() 240: channel 161 busytime 1 [ 46.029082] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=165, ctrl_ch2=0, cent_ch=165 DBDCIdx=1, ChBand=1, BW=0, TXStream=3, RXStream=3, scan(1) [ 46.530453] 7981@C23L2,UpdateChannelInfo() 240: channel 165 busytime 0 [ 46.536996] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 36 : Busy Time = 3086, Score 97,Skip Channel = FALSE [ 46.547862] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 40 : Busy Time = 4077, Score 96,Skip Channel = FALSE [ 46.558722] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 44 : Busy Time = 1921, Score 99,Skip Channel = FALSE [ 46.569595] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 48 : Busy Time = 3922, Score 97,Skip Channel = FALSE [ 46.580459] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 52 : Busy Time = 4346, Score 96,Skip Channel = TRUE [ 46.591242] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 56 : Busy Time = 6026, Score 94,Skip Channel = TRUE [ 46.602020] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 60 : Busy Time = 3460, Score 97,Skip Channel = TRUE [ 46.612794] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 64 : Busy Time = 3662, Score 97,Skip Channel = TRUE [ 46.623572] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 149 : Busy Time = 134, Score 99,Skip Channel = FALSE [ 46.634442] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 153 : Busy Time = 453, Score 99,Skip Channel = FALSE [ 46.645303] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 157 : Busy Time = 0, Score 100,Skip Channel = FALSE [ 46.656076] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 161 : Busy Time = 1, Score 99,Skip Channel = FALSE [ 46.666761] 7981@C23L2,select_clear_channel_bw_160M() 1596: Channel 165 : Busy Time = 0, Score 99,Skip Channel = FALSE [ 46.677453] 7981@C23L2,select_clear_channel_bw_160M() 1599: for BW 160M, select the best primary channel 44 [ 46.687187] 7981@C23L3,Adj_ZeroWait_Status_Update() 1005: ch=44 [ 46.693106] 7981@C23L3,RadarStateCheck() 239: Zero Wait State: 2 [ 46.699110] 7981@C23L3,RadarStateCheck() 285: RD_NORMAL_MODE [ 46.705917] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 46.714453] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=36, ctrl_ch2=0, cent_ch=42 DBDCIdx=1, ChBand=1, BW=2, TXStream=3, RXStream=3, scan(0) [ 46.968998] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 46.977487] 7981@C23L3,DfsBuildChannelList() 3532: Done [ 46.982728] 7981@C23L3,zero_wait_dfs_switch_ch() 925: outband ch 44, ch_stat 0 [ 46.989958] 7981@C23L3,zero_wait_dfs_switch_ch() 932: bDedicatedZeroWaitDefault == 0 [ 46.997973] 7981@C08L2,APStartUpForMbss() 993: ===>(caller:ap_inf_open+0x138/0x4b8 [mt_wifi]), mbss_idx:8, CfgMode:0 [ 47.008521] 7981@C15L2,APPMFInit() 133: [PMF] apidx=8, MFPC=0, MFPR=0, SHA256=0 [ 47.015869] 7981@C18L3,BuildChannelList() 475: [ 47.020734] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 47.028384] WiFi@C08L2,ap_link_up() 7068: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(8) [ 47.037013] 7981@C01L3,wifi_sys_linkup() 1150: wdev idx = 8 [ 47.121717] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=8 [ 47.131901] 7981@C08L3,UpdateBeaconHandler() 1935: BCN_UPDATE_INIT, OmacIdx = 0 (rai0) [ 47.139847] 7981@C08L3,UpdateBeaconHandler() 1948: Band1 BcnInitedRnd = 122 [ 47.168057] PrintSrCmd: [ 47.168057] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.168057] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 47.182115] PrintSrCmd: [ 47.182115] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.182115] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.196163] PrintSrCmd: [ 47.196163] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.196163] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 47.210165] PrintSrCmd: [ 47.210165] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.210165] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.224260] PrintSrCmd: [ 47.224260] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.224260] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.238341] PrintSrCmd: [ 47.238341] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.238341] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.252445] 7981@C03L3,MtCmdTxPwrShowInfo() 13711: ucTxPowerInfoCatg: 2, BandIdx: 1 [ 47.260190] 7981@C03L3,MtCmdTxPwrShowInfo() 13740: (ret = 0) [ 47.260294] [mtf_txpower_all_rate_info] band_idx:1 pwr:48 ChBand:5G ePAGain:0 [ 47.265859] mtk_ppe_dev_register_hook : ineterface rai0 register (3) [ 47.281759] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.291160] br-lan: port 7(rai0) entered blocking state [ 47.296415] br-lan: port 7(rai0) entered disabled state [ 47.301923] device rai0 entered promiscuous mode [ 47.306705] br-lan: port 7(rai0) entered blocking state [ 47.311951] br-lan: port 7(rai0) entered forwarding state [ 47.321507] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.332793] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.345004] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.355414] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.363460] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.448943] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.456810] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.464973] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.473214] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.482626] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.490551] 7981@C08L2,mbss_virtual_if_open() 134: ===> rai4 [ 47.496375] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 47.504479] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 47.512562] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 12 [ 47.518281] 7981@C18L3,BuildChannelList() 475: [ 47.522875] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 47.531541] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=36, ctrl_ch2=0, cent_ch=42 DBDCIdx=1, ChBand=1, BW=2, TXStream=3, RXStream=3, scan(0) [ 47.557628] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 47.566422] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 47.574471] wdev_attr_update(): wdevId12 = e2:ef:02:c3:71:22 [ 47.580196] WiFi@C12L1,wifi_sys_open() 891: wifi_sys_open():band1 group_idx[12]=25, bw_grp=16 omac=17 [ 47.589568] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=12 [ 47.598320] 7981@C02L2,AsicRadioOnOffCtrl() 2291: DbdcIdx=1 RadioOn [ 47.605304] 7981@C00L2,ApAutoChannelAtBootUp() 338: -----------------> [ 47.611964] 7981@C00L3,ApAutoChannelAtBootUp() 349: [QIHOO]OriChannel 36 [ 47.618813] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 47.624420] 7981@C03L1,MtCmdSetMacTxRx() 10211: (ret = 0) [ 47.629928] 7981@C23L3,RadarStateCheck() 239: Zero Wait State: 2 [ 47.635997] 7981@C23L3,RadarStateCheck() 285: RD_NORMAL_MODE [ 47.642852] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 47.651429] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=36, ctrl_ch2=0, cent_ch=42 DBDCIdx=1, ChBand=1, BW=2, TXStream=3, RXStream=3, scan(0) [ 47.674710] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 47.678147] led_log: pid 10057 ppid 5992 role_type unknown [ 47.678147] [ 47.683262] 7981@C23L3,DfsBuildChannelList() 3532: Done [ 47.692299] led_log: pid 10058 ppid 5992 wifi_result unknown [ 47.692299] [ 47.695402] 7981@C23L3,zero_wait_dfs_switch_ch() 925: outband ch 44, ch_stat 0 [ 47.695406] 7981@C23L3,zero_wait_dfs_switch_ch() 932: bDedicatedZeroWaitDefault == 0 [ 47.695599] 7981@C08L2,APStartUpForMbss() 993: ===>(caller:ap_inf_open+0x138/0x4b8 [mt_wifi]), mbss_idx:12, CfgMode:0 [ 47.728125] 7981@C15L2,APPMFInit() 133: [PMF] apidx=12, MFPC=0, MFPR=0, SHA256=0 [ 47.735558] 7981@C18L3,BuildChannelList() 475: [ 47.740371] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 47.747972] WiFi@C08L2,ap_link_up() 7068: (caller:wdev_do_linkup+0x20/0x38 [mt_wifi]), wdev(12) [ 47.756680] 7981@C01L3,wifi_sys_linkup() 1150: wdev idx = 12 [ 47.832194] 7981@C08L3,hw_ctrl_flow_v2_link_up() 72: wdev_idx=12 [ 47.842753] 7981@C08L3,UpdateBeaconHandler() 1935: BCN_UPDATE_INIT, OmacIdx = 11 (rai4) [ 47.863790] PrintSrCmd: [ 47.863790] u1CmdSubId = 1, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.863790] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 47.877800] PrintSrCmd: [ 47.877800] u1CmdSubId = 5, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.877800] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.891796] PrintSrCmd: [ 47.891796] u1CmdSubId = 3, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.891796] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 1 [ 47.905865] PrintSrCmd: [ 47.905865] u1CmdSubId = 23, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.905865] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.919988] PrintSrCmd: [ 47.919988] u1CmdSubId = 31, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.919988] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.934072] PrintSrCmd: [ 47.934072] u1CmdSubId = 33, u1ArgNum = 0, u1DbdcIdx = 1, u1Status = 0 [ 47.934072] u1DropTaIdx = 0, u1StaIdx = 0, u4Value = 0 [ 47.948217] 7981@C03L3,MtCmdTxPwrShowInfo() 13711: ucTxPowerInfoCatg: 2, BandIdx: 1 [ 47.955984] 7981@C03L3,MtCmdTxPwrShowInfo() 13740: (ret = 0) [ 47.961648] [mtf_txpower_all_rate_info] band_idx:1 pwr:48 ChBand:5G ePAGain:0 [ 47.968796] mtk_ppe_dev_register_hook : ineterface rai4 register (4) [ 47.975838] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.984398] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 47.993031] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.000955] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.011456] br-lan: port 8(rai4) entered blocking state [ 48.016702] br-lan: port 8(rai4) entered disabled state [ 48.022219] device rai4 entered promiscuous mode [ 48.026994] br-lan: port 8(rai4) entered blocking state [ 48.032249] br-lan: port 8(rai4) entered forwarding state [ 48.038055] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.118263] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.127649] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.135705] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.143833] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.151898] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.159769] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.167697] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.176334] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.184401] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.192360] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 48.207001] device ra0 left promiscuous mode [ 48.211401] br-lan: port 5(ra0) entered disabled state [ 48.259978] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:8 [ 48.266108] br-lan: port 5(ra0) entered blocking state [ 48.271274] br-lan: port 5(ra0) entered disabled state [ 48.276663] device ra0 entered promiscuous mode [ 48.281304] br-lan: port 5(ra0) entered blocking state [ 48.286463] br-lan: port 5(ra0) entered forwarding state [ 48.302433] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:0 [ 48.308562] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:1 [ 48.316465] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:2 [ 48.322863] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:3 [ 48.329207] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 16 [ 48.336559] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 9 [ 48.344077] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 111) [ 48.350756] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 110) [ 48.389887] device ra4 left promiscuous mode [ 48.394311] br-lan: port 6(ra4) entered disabled state [ 48.414181] br-lan: port 6(ra4) entered blocking state [ 48.419347] br-lan: port 6(ra4) entered disabled state [ 48.424738] device ra4 entered promiscuous mode [ 48.429503] br-lan: port 6(ra4) entered blocking state [ 48.434660] br-lan: port 6(ra4) entered forwarding state [ 48.487699] br-lan: port 9(apcli0) entered blocking state [ 48.493138] br-lan: port 9(apcli0) entered disabled state [ 48.498801] device apcli0 entered promiscuous mode [ 48.548621] Set_Fh_Bss_Proc rai4 wdev->MAPCfg.DevOwnRole 0x0 [ 48.561520] Set_Fh_Bss_Proc rai4 wdev->MAPCfg.DevOwnRole 0x20 [ 48.575852] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=0] [ 48.593409] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x0 [ 48.601419] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 [ 48.610357] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=0] [ 48.619829] device rai0 left promiscuous mode [ 48.624338] br-lan: port 7(rai0) entered disabled state [ 48.636403] br-lan: port 7(rai0) entered blocking state [ 48.641655] br-lan: port 7(rai0) entered disabled state [ 48.647130] device rai0 entered promiscuous mode [ 48.651916] br-lan: port 7(rai0) entered blocking state [ 48.657157] br-lan: port 7(rai0) entered forwarding state [ 48.662960] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x0 [ 48.673090] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 [ 48.681531] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=0] [ 48.695638] Set_Fh_Bss_Proc ra4 wdev->MAPCfg.DevOwnRole 0x0 [ 48.703807] Set_Fh_Bss_Proc ra4 wdev->MAPCfg.DevOwnRole 0x20 [ 48.714737] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=0] [ 48.734751] device rai4 left promiscuous mode [ 48.739308] br-lan: port 8(rai4) entered disabled state [ 48.760322] br-lan: port 8(rai4) entered blocking state [ 48.765565] br-lan: port 8(rai4) entered disabled state [ 48.771027] device rai4 entered promiscuous mode [ 48.775792] br-lan: port 8(rai4) entered blocking state [ 48.781028] br-lan: port 8(rai4) entered forwarding state [ 48.823748] br-lan: port 10(apclii0) entered blocking state [ 48.829355] br-lan: port 10(apclii0) entered disabled state [ 48.835176] device apclii0 entered promiscuous mode [ 49.219947] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 49.228104] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 49.236232] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 16 [ 49.241939] 7981@C18L3,BuildChannelList() 475: [ 49.246800] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 49.254970] wdev_attr_update(): wdevId16 = e6:ef:02:63:71:22 [ 49.260749] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=16 [ 49.267155] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 49.274617] mtk_ppe_dev_register_hook : ineterface apcli0 register (5) [ 49.281397] br-lan: port 9(apcli0) entered blocking state [ 49.286820] br-lan: port 9(apcli0) entered forwarding state [ 49.292774] br-lan: port 9(apcli0) entered disabled state [ 49.735649] led_log: pid 10539 ppid 5992 role_type unknown [ 49.735649] [ 49.744152] led_log: pid 10540 ppid 5992 wifi_result unknown [ 49.744152] [ 50.303419] 7981@C01L2,RTMP_COM_IoctlHandle() 1511: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_INIT [ 50.311628] 7981@C01L2,RTMP_COM_IoctlHandle() 1488: -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP [ 50.319674] WiFi@C01L3,wifi_sys_open() 840: wdev idx = 17 [ 50.325361] 7981@C18L3,BuildChannelList() 475: [ 50.329990] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 50.338628] 7981@C03L3,MtCmdChannelSwitch() 2529: ctrl_chl=36, ctrl_ch2=0, cent_ch=42 DBDCIdx=1, ChBand=1, BW=2, TXStream=3, RXStream=3, scan(0) [ 50.361847] 7981@C08L3,DfsCacNormalStart() 3380: [RDM] TX80/RX160 mode, CAC 65 seconds start [ 50.370604] WiFi@C00L2,dump_ht_cap() 29: Caller: wlan_operate_init+0xa4/0x148 [mt_wifi] [ 50.378673] wdev_attr_update(): wdevId17 = ea:ef:02:63:71:22 [ 50.384355] 7981@C08L3,hw_ctrl_flow_v2_open() 13: wdev_idx=17 [ 50.391534] WiFi@C00L2,dump_ht_cap() 29: Caller: dump_ht_cap+0x10/0x20 [mt_wifi] [ 50.398996] mtk_ppe_dev_register_hook : ineterface apclii0 register (6) [ 50.405845] br-lan: port 10(apclii0) entered blocking state [ 50.411427] br-lan: port 10(apclii0) entered forwarding state [ 50.417508] br-lan: port 10(apclii0) entered disabled state [ 50.495957] -->mtfwd_exit() [ 50.496000] <--mtfwd_exit() [ 50.533125] Current mapfilter version v3.0.1.2 [ 50.568968] Set_Map_Proc current MAP MODE is 1 [ 50.574907] SetApCliEnableByWdev: I/F(apcli0) (enable = 0) [ 50.596643] Set_Map_Proc current MAP MODE is 1 [ 50.602543] SetApCliEnableByWdev: I/F(apcli1) (enable = 0) [ 51.784977] led_log: pid 10638 ppid 5992 role_type unknown [ 51.784977] [ 51.793638] led_log: pid 10639 ppid 5992 wifi_result unknown [ 51.793638] remove br_guest module=guest_network_separation [ 53.799603] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.808909] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 53.821080] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.830405] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 53.833421] led_log: pid 10714 ppid 5992 role_type unknown [ 53.833421] [ 53.847118] led_log: pid 10716 ppid 5992 wifi_result unknown [ 53.847118] [ 53.848106] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.863519] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 53.875371] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.884532] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 53.960528] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.978578] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 53.987847] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 53.998549] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.009061] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.115815] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 54.136941] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 54.146815] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.157421] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.167959] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.904331] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 54.913559] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 54.952130] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 4 [ 54.961348] 7981@C12L3,Set_VLAN_Policy_Proc() 14349: Set the VLAN checking policy : 2 [ 55.887100] led_log: pid 11163 ppid 5992 role_type unknown [ 55.887100] [ 55.895527] led_log: pid 11164 ppid 5992 wifi_result unknown [ 55.895527] [iptv]iptv_delete_rule:[604] old config:enable:0, vlan_id:45, mask:0 [ 57.189781] SetApCliEnableByWdev: I/F(apcli0) (enable = 0) [ 57.198499] SetApCliEnableByWdev: I/F(apcli1) (enable = 0) [ 57.307290] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.315277] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.323143] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.331001] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.338857] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.346703] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.424910] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [1905Daemon][mai[ 57.433102] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! n] Current Versi[ 57.443018] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! on v3.0.1.2 [19[ 57.451376] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.460506] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.468468] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [1905Daemon][map_read_config_file] map_agent_alid = e0:ef:02:63:71:21 [1905Daemon][map_read_config_file] br_inf = br-lan [1905Daemon][map_read_config_file] bss_config_priority: ra4;ra0;rai4;rai0;apcli0;apclii0 [1905Daemon][map_read_config_file] lan = eth0.1 [1905Daemon][map_read_config_file] lan = eth0.2 [1905Daemon][map_read_config_file] lan = eth0.3 [1905Daemon][map_read_config_file] wan = eth1 [1905Daemon][map_read_config_file] set discovery_cnt to defaut value(11) cmdu_init set send buffer size 458752 cmdu_init set recv buffer size 458752 [ 57.545461] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.545517] do_map_set_ctl==>cmd(1905) [ 57.553325] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! [ 57.557051] do_map_set_ctl==>almac(e0:ef:02:63:71:21) [1905Daemon][cmd[ 57.557055] sp update own almac toe0:ef:02:63:71:21 u_init] br mac a[ 57.576249] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! ddr e0:ef:02:63:[ 57.585743] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! 71:20_1905_inter[ 57.594679] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! face_open_sock s[ 57.604251] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! et send buffer size 458752 _1905_interface_open_sock set recv buffer size 458752 [1905Daemon][_1905_interface_set_sock_buf] alloc 1905 sock_buf :20480! [1905Daemon][read_con[ 57.627645] traffic separation is off fig_file] br_lan=br-lan [1905Daemon][parse_eth_lan_interface] lan_interface[0]=eth0.1 [1905Daemon][parse_eth_lan_interface] lan_interface[1]=eth0.2 [1905Daemon][parse_eth_lan_interface] lan_interface[2]=eth0.3 [1905Daemon][read_config_file] unknown config line lan_vid [1905Daemon][read_config_file] unknown config line wan_vid [1905Daemon][read_config_file] unknown config line ethernet_dev_name [1905Daemon][read_config_file] parse ext phy port [1905Daemon][parse_ext_phy_port] ext_phy_port[0]=0 [1905Daemon][parse_ext_phy_port] ext_phy_port[1]=1 [1905Daemon][parse_ext_phy_port] [ 57.681961] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! ext_phy_port[2]=[ 57.691765] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! 2 [1905Daemon][[ 57.700996] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! parse_ext_phy_po[ 57.709744] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! rt] ext_phy_port[ 57.719122] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:8 [3]=3 [1905Daem[ 57.726486] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! on][get_port_no][ 57.735665] 7981@C12L1,rt28xx_ap_ioctl() 833: interface is down, cmd [8be1] return!!! eth0.1 (1) [19[ 57.745122] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:0 05Daemon][get_po[ 57.752563] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:1 rt_no] eth0.2 (2[ 57.759987] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:2 ) [1905Daemon][[ 57.767418] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:3 get_port_no] eth0.3 (3) [1905Daemon][eth_layer_port_init] MAX_LAN_PORT_NUM=7 [1905Daemon][eth_layer_port_init] init eth_data[0]=0 [1905Daemon][eth_layer_port_init] init eth_data[1]=1 [1905Daemon][eth_layer_port_init] init eth_data[2]=2 [1905Daemon][eth_layer_port_init] init eth_data[3]=3 [1905Daemon][eth_layer_port_init] init eth_data[4]=4 [1905Daemon][eth_layer_port_init] init eth_data[5]=[ 57.808430] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:8 5 [1905Daemon][[ 57.815588] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:0 eth_layer_port_i[ 57.823007] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:1 nit] init eth_da[ 57.830479] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:2 ta[6]=6 [1905Da[ 57.837930] 7981@C14L1,set_wapp_param() 3310: Unknown Parameter:3 emon][get_port_t[ 57.845445] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 16 ype] lan_port=00[ 57.853940] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 9 000007, wan_port[ 57.862722] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 111) =00000008 [1905[ 57.870132] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 110) Daemon][eth_laye[ 57.877869] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 16 r_port_init] lan[ 57.886404] 7981@C12L1,Set_AP_VENDOR_SPECIFIC_IE() 3558: Unknown OUIType = 9 _port=00000007, [ 57.894835] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 111) wan_port=0000000[ 57.902596] 7981@C12L1,set_wapp_cmm_ie() 3454: Unknown IE(EID = 110) 8 [1905Daemon][eth_layer_port_init] assign eth_data[0]=0 [1905Daemon][eth_layer_port_init] assign eth_data[1]=[ 57.918563] Set_Fh_Bss_Proc ra4 wdev->MAPCfg.DevOwnRole 0x0 1 [1905Daemon][eth_layer_port_init] assign eth_data[2]=2 [1905Daemon][eth_layer_port_init] lan_finished=0 j=3 [1905Daemon][eth_layer_port_ini[ 57.936946] Set_Fh_Bss_Proc ra4 wdev->MAPCfg.DevOwnRole 0x20 t] assign eth_data[3]=3 wan_port = true [1905Daemon][main] p190[ 57.948944] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=1] 5_Manager Daemon Running [ 57.959865] [HNAT] LAN IP: 192.168.2.1 LAN MASK: 255.255.255.0 [ 57.962295] led_log: pid 11335 ppid 5992 role_type unknown [ 57.962295] [ 57.968730] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x0 [ 57.981276] led_log: pid 11338 ppid 5992 wifi_result unknown [ 57.981276] [ 57.990655] Set_Fh_Bss_Proc ra0 wdev->MAPCfg.DevOwnRole 0x20 [ 58.001647] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=1] [ 58.013720] Set_Fh_Bss_Proc rai4 wdev->MAPCfg.DevOwnRole 0x0 [ 58.022808] Set_Fh_Bss_Proc rai4 wdev->MAPCfg.DevOwnRole 0x20 [ 58.031423] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=1] [ 58.043281] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x0 [ 58.051277] Set_Fh_Bss_Proc rai0 wdev->MAPCfg.DevOwnRole 0x20 [ 58.059651] 7981@C12L1,RTMPAPPrivIoctlSet() 3568: IOCTL::(iwpriv) Command not Support [MapChannelEn=1] worker task status change, send to receiver port:0 0 [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [0] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree worker task status change, send to receiver port:1 0 [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [1] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree worker task status change, send to receiver port:2 0 [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [2] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree worker task status change, send to receiver port:3 0 worker task status change, send to receiver port:4 0 [1905Daemon][eth_layer_port_data_update_and_notify] worker task status change, send to receiver port:5 0 [TOPO]port [3] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [4] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [5] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree worker task status change, send to receiver port:6 0 [1905Daemon][eth_layer_port_data_update_and_notify] [TOPO]port [6] DOWN [1905Daemon][update_topology_tree] [TOPO]root leaf not exist, could not update topology tree [1905Daemon][map_event_handler] receive LIB_SYNC_RECV_BUF_SIZE (notify len:235, peer len:15360) from mapd, own real len:20480, default len:20480 [1905Daemon][_1905_interface_set_sock_buf] alloc 1905 sock_buf :20480! [1905Daemon][map_event_handler] change own real len success:20480 [1905Daemon][map_event_handler] change peer len success:15360 [1905Daemon][_1905_send_sync_recv_buf_size_rsp] _1905_SYNC_RECV_BUF_SIZE_RSP_EVENT send to mapd success, change_len:20480, rsp:1 [1905Daemon][init_wireless_interface] itf name = ra4 [1905Daemon][init_wireless_interface] itf name = ra0 [1905Daemon][init_wireless_interface] itf name = rai4 [1905Daemon][init_wireless_interface] itf name = rai0 [1905Daemon][init_wireless_interface] itf name = apcli0 [1905Daemon][init_wireless_interface] itf name = apclii0 [1905Daemon][lldpdu_init] create lldpdu on eth0.1-sock(22) success [1905Daemon][lldpdu_init] create lldpdu on eth0.2-sock(23) success [1905Daemon][lldpdu_init] create lldpdu on eth0.3-sock(24) success [1905Daemon][lldpdu_init] create lldpdu on eth1-sock(25) success [1905Daemon][lldpdu_init] create lldpdu on ra4-sock(26) success [1905Daemon][lldpdu_init] create lldpdu on ra0-sock(27) success [1905Daemon][lldpdu_init] create lldpdu on rai4-sock(28) success [1905Daemon][lldpdu_init] create lldpdu on rai0-sock(29) success [1905Daemon][lldpdu_init] create lldpdu on apcli0-sock(30) success [1905Daemon][lldpdu_init] create lldpdu on apclii0-sock(31) success [1905Daemon][set_bss_config_priority_by_str] bss intf(ra4) priority=1 [1905Daemon][set_bss_config_priority_by_str] bss intf(ra0) priority=2 [1905Daemon][set_bss_config_priority_by_str] bss intf(rai4) priority=3 [1905Daemon][set_bss_config_priority_by_str] bss intf(rai0) priority=4 [1905Daemon][set_bss_config_priority_by_str] bss intf(apcli0) priority=5 [1905Daemon][set_bss_config_priority_by_str] bss intf(apclii0) priority=6 [1905Daemon][common_info_init] eth0.1 is eth interface; enable all tx rx [1905Daemon][common_info_init] eth0.2 is eth interface; enable all tx rx [1905Daemon][common_info_init] eth0.3 is eth interface; enable all tx rx [1905Daemon][common_info_init] eth1 is eth interface; enable all tx rx [ 60.680592] dynamic load balance is off [ 60.684483] mapfilter: Start drop the specific ip packets now !! [ 60.684483] [ 60.696318] led_log: pid 11439 ppid 5992 role_type CAP [ 60.696318] [ 60.698237] ----->free map device rcu 00000000be11d493 [ 60.707019] led_log: pid 11440 ppid 5992 wifi_result connect_success_near [ 60.707019] [ 60.710500] ----->free map device rcu 000000005fcf0407 [ 60.710502] ----->free map device rcu 0000000042332621 Failed to connetct to generic netlink switch mt753x layer init fail netlink_phy_reg_read fail [1905Daemon][eth_get_port_status] fail to get_port_status index(2) worker task status -1 Failed to connetct to generic netlink switch mt753x layer init fail netlink_phy_reg_read fail [1905Daemon][eth_get_port_status] fail to get_port_status index(3) worker task status -1 [1905Daemon][auto_set_bh_bss_acl] controller lose, auto_set_bh_bss_acl. [ 62.657600] mapfilter: Stop drop the specific ip packets now !! [ 62.657600] [ 62.769694] led_log: pid 11504 ppid 5992 role_type NonCAP [ 62.769694] [ 62.785632] led_log: pid 11505 ppid 5992 wifi_result connect_fail [ 62.785632]

F0: 102B 0000 FA: 1040 0000 FA: 1040 0000 [0200] F9: 0000 0000 V0: 0000 0000 [0001] 00: 0000 0000 BP: 2400 0041 [0000] G0: 1190 0000 EC: 0000 0000 [1000] T0: 0000 0239 [010F] Jump to BL NOTICE: BL2: v2.7(release):OpenWrt v2022-08-31-75393484-1 (mt7981-spim-nand-ddr3) NOTICE: BL2: Built : 20:00:48, May 31 2023 NOTICE: WDT: disabled NOTICE: EMI: Using DDR3 settings NOTICE: EMI: Detected DRAM size: 256MB NOTICE: EMI: complex R/W mem test passed NOTICE: CPU: MT7981 (1300MHz) NOTICE: SPI_NAND parses attributes from parameter page. NOTICE: SPI_NAND Detected ID 0xc8 NOTICE: Page size 2048, Block size 131072, size 134217728 NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.7(release):OpenWrt v2022-08-31-75393484-1 (mt7981-spim-nand-ddr3) NOTICE: BL31: Built : 20:00:48, May 31 2023 U-Boot 2023.04-OpenWrt-r23201-4c5a9da869 (May 31 2023 - 20:00:48 +0000) CPU: MediaTek MT7981 Model: Qihoo 360T7 DRAM: 256 MiB Core: 40 devices, 18 uclasses, devicetree: embed Loading Environment from UBI... spi-nand: spi_nand spi_nand@0: GigaDevice SPI NAND was found. spi-nand: spi_nand spi_nand@0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 Read 126976 bytes from volume ubootenv to 000000004f7c1c80 Read 126976 bytes from volume ubootenv2 to 000000004f7e0cc0 OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 reset button found Loading Environment from UBI... UBI partition 'ubi' already selected Read 126976 bytes from volume ubootenv to 000000004f7c1c80 Read 126976 bytes from volume ubootenv2 to 000000004f7e0cc0 OK Net: eth0: ethernet@15100000 No EFI system partition No EFI system partition Failed to persist EFI variables ( ( ( OpenWrt ) ) ) U-Boot 2023.04-OpenWrt-r23201-4c5a9da869 (May 31 2023 - 20:00:48 +0000) 1. Run default boot command. 2. Boot system via TFTP. 3. Boot production system from NAND. 4. Boot recovery system from NAND. 5. Load production system via TFTP then write to NAND. 6. Load recovery system via TFTP then write to NAND. 7. Load BL31+U-Boot FIP via TFTP then write to NAND. 8. Load BL2 preloader via TFTP then write to NAND. 9. Reboot. a. Reset all settings to factory defaults. 0. U-Boot console Press UP/DOWN to move, ENTER to select, ESC to quit No size specified -> Using max size (9777152) Read 9777152 bytes from volume fit to 0000000046000000 ## Checking Image at 46000000 ... FIT image found FIT description: ARM64 OpenWrt FIT (Flattened Image Tree) Image 0 (kernel-1) Description: ARM64 OpenWrt Linux-5.15.114 Type: Kernel Image Compression: gzip compressed Data Start: 0x46001000 Data Size: 5260909 Bytes = 5 MiB Architecture: AArch64 OS: Linux Load Address: 0x48000000 Entry Point: 0x48000000 Hash algo: crc32 Hash value: 23dca11a Hash algo: sha1 Hash value: fc5a5d6e34cad1ca272effe15dc5d631c73de999 Image 1 (fdt-1) Description: ARM64 OpenWrt qihoo_360t7 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x46506000 Data Size: 32768 Bytes = 32 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 86810e23 Hash algo: sha1 Hash value: 37decafe69f87f0fecabb97e2e1db3a29f1cad99 Image 2 (rootfs-1) Description: ARM64 OpenWrt qihoo_360t7 rootfs Type: Filesystem Image Compression: uncompressed Data Start: 0x4650e000 Data Size: 4354048 Bytes = 4.2 MiB Hash algo: crc32 Hash value: 4768dc7d Hash algo: sha1 Hash value: bcb2ce46fe7631c08ba67448ac91667f09e0304b Default Configuration: 'config-1' Configuration 0 (config-1) Description: OpenWrt qihoo_360t7 Kernel: kernel-1 FDT: fdt-1 Loadables: rootfs-1 ## Checking hash(es) for FIT Image at 46000000 ... Hash(es) for Image 0 (kernel-1): crc32+ sha1+ Hash(es) for Image 1 (fdt-1): crc32+ sha1+ Hash(es) for Image 2 (rootfs-1): crc32+ sha1+ ## Loading kernel from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-5.15.114 Type: Kernel Image Compression: gzip compressed Data Start: 0x46001000 Data Size: 5260909 Bytes = 5 MiB Architecture: AArch64 OS: Linux Load Address: 0x48000000 Entry Point: 0x48000000 Hash algo: crc32 Hash value: 23dca11a Hash algo: sha1 Hash value: fc5a5d6e34cad1ca272effe15dc5d631c73de999 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 46000000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt qihoo_360t7 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x46506000 Data Size: 32768 Bytes = 32 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 86810e23 Hash algo: sha1 Hash value: 37decafe69f87f0fecabb97e2e1db3a29f1cad99 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x46506000 Working FDT set to 46506000 ## Loading loadables from FIT Image at 46000000 ... Trying 'rootfs-1' loadables subimage Description: ARM64 OpenWrt qihoo_360t7 rootfs Type: Filesystem Image Compression: uncompressed Data Start: 0x4650e000 Data Size: 4354048 Bytes = 4.2 MiB Hash algo: crc32 Hash value: 4768dc7d Hash algo: sha1 Hash value: bcb2ce46fe7631c08ba67448ac91667f09e0304b Verifying Hash Integrity ... crc32+ sha1+ OK Uncompressing Kernel Image Loading Device Tree to 000000004e7e2000, end 000000004e7ecfff ... OK Working FDT set to 4e7e2000 Add 'ramoops@42ff0000' node failed: FDT_ERR_EXISTS Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.15.114 (gch981213@guoguo-thinkbook) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r22396+773-95cae498b6) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Wed May 31 20:00:48 2023 [ 0.000000] Machine model: Qihoo 360T7 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x0000000047c7ffff] [ 0.000000] node 0: [mem 0x0000000047c80000-0x0000000047ffffff] [ 0.000000] node 0: [mem 0x0000000048000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632 [ 0.000000] pcpu-alloc: s29592 r8192 d31848 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512 [ 0.000000] Kernel command line: [ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240952K/262144K available (8128K kernel code, 894K rwdata, 2212K rodata, 448K init, 286K bss, 21192K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000128] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000138] pid_max: default: 32768 minimum: 301 [ 0.000425] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.000435] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001704] rcu: Hierarchical SRCU implementation. [ 0.002052] smp: Bringing up secondary CPUs ... [ 0.002365] Detected VIPT I-cache on CPU1 [ 0.002390] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.002418] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.002483] smp: Brought up 1 node, 2 CPUs [ 0.002497] SMP: Total of 2 processors activated. [ 0.002502] CPU features: detected: 32-bit EL0 Support [ 0.002506] CPU features: detected: CRC32 instructions [ 0.002533] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.002595] CPU: All CPU(s) started at EL2 [ 0.002607] alternatives: patching kernel code [ 0.005576] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.005599] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.005734] pinctrl core: initialized pinctrl subsystem [ 0.006385] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.006691] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.006720] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.006744] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.007078] thermal_sys: Registered thermal governor 'fair_share' [ 0.007082] thermal_sys: Registered thermal governor 'bang_bang' [ 0.007087] thermal_sys: Registered thermal governor 'step_wise' [ 0.007091] thermal_sys: Registered thermal governor 'user_space' [ 0.007253] ASID allocator initialised with 65536 entries [ 0.007674] pstore: Registered ramoops as persistent store backend [ 0.007681] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.017340] cryptd: max_cpu_qlen set to 1000 [ 0.019563] SCSI subsystem initialized [ 0.019720] libata version 3.00 loaded. [ 0.020825] clocksource: Switched to clocksource arch_sys_counter [ 0.021461] NET: Registered PF_INET protocol family [ 0.021551] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.021879] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.021896] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.021905] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.021924] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.021953] TCP: Hash tables configured (established 2048 bind 2048) [ 0.022023] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.022041] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.022150] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.022172] PCI: CLS 0 bytes, default 64 [ 0.024619] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.028159] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.028174] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.062439] pwm-mediatek 10048000.pwm: clock: top fail: -517 [ 0.071469] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.072319] printk: console [ttyS0] disabled [ 0.092488] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 18, base_baud = 2500000) is a ST16650V2 [ 0.706706] printk: console [ttyS0] enabled [ 0.711721] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.720771] loop: module loaded [ 0.725470] spi-nand spi0.0: ESMT SPI NAND was found. [ 0.730520] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.738883] 8 fixed-partitions partitions found on MTD device spi0.0 [ 0.745257] Creating 8 MTD partitions on "spi0.0": [ 0.750039] 0x000000000000-0x000000100000 : "bl2" [ 0.755856] 0x000000100000-0x000000180000 : "u-boot-env" [ 0.761915] 0x000000180000-0x000000380000 : "Factory" [ 0.768725] 0x000000380000-0x000000580000 : "fip" [ 0.775362] 0x000000580000-0x000007180000 : "ubi" [ 0.846946] 0x000007180000-0x000007280000 : "config" [ 0.853081] 0x000007280000-0x000007300000 : "factory" [ 0.858906] 0x000007300000-0x000007a00000 : "log" [ 1.016225] mtk_soc_eth 15100000.ethernet: generated random MAC address 8a:40:d4:9c:26:7c [ 1.025205] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009480000, irq 82 [ 1.034776] i2c_dev: i2c /dev entries driver [ 1.040268] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.048970] NET: Registered PF_INET6 protocol family [ 1.054729] Segment Routing with IPv6 [ 1.058410] In-situ OAM (IOAM) with IPv6 [ 1.062401] NET: Registered PF_PACKET protocol family [ 1.067580] 8021q: 802.1Q VLAN Support v1.8 [ 1.072834] pstore: Using crash dump compression: deflate [ 1.126894] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode [ 1.136297] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.149540] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=91) [ 1.170084] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=92) [ 1.190266] mt7530-mdio mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=93) [ 1.210414] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=94) [ 1.221908] DSA: tree 0 setup [ 1.225828] UBI: auto-attach mtd4 [ 1.229163] ubi0: default fastmap pool size: 40 [ 1.233713] ubi0: default fastmap WL pool size: 20 [ 1.238492] ubi0: attaching mtd4 [ 1.993880] ubi0: scanning is finished [ 2.008485] ubi0: attached mtd4 (name "ubi", size 108 MiB) [ 2.013986] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.020853] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.027628] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.034581] ubi0: good PEBs: 864, bad PEBs: 0, corrupted PEBs: 0 [ 2.040575] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128 [ 2.047786] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [ 2.056125] ubi0: available PEBs: 0, total reserved PEBs: 864, PEBs reserved for bad PEB handling: 20 [ 2.065341] ubi0: background thread "ubi_bgt0d" started, PID 406 [ 2.067388] FIT: Selected configuration: "config-1" (OpenWrt qihoo_360t7) [ 2.078153] FIT: kernel sub-image 0x00001000..0x0050566c "kernel-1" (ARM64 OpenWrt Linux-5.15.114) [ 2.088072] FIT: flat_dt sub-image 0x00506000..0x0050dfff "fdt-1" (ARM64 OpenWrt qihoo_360t7 device tree blob) [ 2.098943] FIT: filesystem sub-image 0x0050e000..0x00934fff "rootfs-1" (ARM64 OpenWrt qihoo_360t7 rootfs) [ 2.109198] FIT: selecting configured loadable "rootfs-1" to be root filesystem [ 2.116494] ubiblock0_2: p1(rootfs-1) [ 2.116684] block ubiblock0_2: created from ubi0:2(fit) [ 2.132746] VFS: Mounted root (squashfs filesystem) readonly on device 259:0. [ 2.140058] Freeing unused kernel memory: 448K [ 2.170872] Run /sbin/init as init process [ 2.174958] with arguments: [ 2.177912] /sbin/init [ 2.180606] with environment: [ 2.183744] HOME=/ [ 2.186092] TERM=linux [ 2.409573] init: Console is alive [ 2.413165] init: - watchdog - [ 2.841817] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.872664] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.890074] init: - preinit - [ 3.020850] random: crng init done [ 3.294378] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 3.302906] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 3.314183] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 5.404514] UBIFS (ubi0:3): default file-system created [ 5.410614] UBIFS (ubi0:3): Mounting in unauthenticated mode [ 5.416372] UBIFS (ubi0:3): background thread "ubifs_bgt0_3" started, PID 489 [ 5.502068] UBIFS (ubi0:3): UBIFS: mounted UBI device 0, volume 3, name "rootfs_data" [ 5.509897] UBIFS (ubi0:3): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.519818] UBIFS (ubi0:3): FS size: 92946432 bytes (88 MiB, 732 LEBs), max 743 LEBs, journal size 4698112 bytes (4 MiB, 37 LEBs) [ 5.531464] UBIFS (ubi0:3): reserved for root: 4390089 bytes (4287 KiB) [ 5.538065] UBIFS (ubi0:3): media format: w5/r0 (latest is w5/r0), UUID F2A900A9-503D-4997-B9F2-F6B23ECDC865, small LPT model [ 5.551559] mount_root: overlay filesystem has not been fully initialized yet [ 5.558893] mount_root: switching to ubifs overlay [ 5.567371] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 5.578484] urandom-seed: Seed file not found (/etc/urandom.seed) [ 5.635516] procd: - early - [ 5.638469] procd: - watchdog - [ 6.179070] procd: - watchdog - [ 6.182476] procd: - ubus - [ 6.238351] procd: - init - Please press Enter to activate this console. [ 6.433575] urngd: v1.0.2 started. [ 6.468118] kmodloader: loading kernel modules from /etc/modules.d/* [ 6.482426] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 6.497760] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b [ 6.505340] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36 [ 6.835214] mt7986-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221208201745a [ 6.835214] [ 7.066131] mt7986-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221208201806 [ 7.180968] mt7986-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221208202048 [ 9.503313] PPP generic driver version 2.4.2 [ 9.509117] NET: Registered PF_PPPOX protocol family [ 9.518902] kmodloader: done loading kernel modules from /etc/modules.d/* [ 9.689189] mtdblock: MTD device 'factory' is NAND, please consider using UBI block devices instead. [ 10.596527] mtdblock: MTD device 'factory' is NAND, please consider using UBI block devices instead. [ 15.866511] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 15.885088] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 15.895597] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 15.904309] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 15.911900] device eth0 entered promiscuous mode [ 15.917058] mt7530-mdio mdio-bus:1f lan1: configuring for phy/gmii link mode [ 15.928310] br-lan: port 1(lan1) entered blocking state [ 15.933619] br-lan: port 1(lan1) entered disabled state [ 15.940325] device lan1 entered promiscuous mode [ 15.955580] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode [ 15.967627] mt7530-mdio mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx [ 15.976064] br-lan: port 2(lan2) entered blocking state [ 15.981362] br-lan: port 2(lan2) entered disabled state [ 15.989017] device lan2 entered promiscuous mode [ 15.996966] br-lan: port 2(lan2) entered blocking state [ 16.002237] br-lan: port 2(lan2) entered forwarding state [ 16.007754] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 16.017325] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode [ 16.028120] br-lan: port 3(lan3) entered blocking state [ 16.033390] br-lan: port 3(lan3) entered disabled state [ 16.040746] device lan3 entered promiscuous mode [ 16.052931] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode

Space for additional notes, links to forum threads or other resources.

...

U-boot MT7981B 128Flash 12v powered GigabitEthernet

Qihoo 360T7 / 360T7M / 360T7U

Supported Versions

Experimental Versions

Hardware Highlights

Installation

Flash Layout

OEM installation using the TFTP method

Specific values needed for tftp

Upgrading OpenWrt

LuCI Web Upgrade Process

Terminal Upgrade Process

sysupgrade

Debricking

Failsafe mode

Basic configuration

Specific Configuration

Network interfaces

Switch Ports (for VLANs)

Buttons

Hardware

Info

Photos

Opening the case

Serial

JTAG

Bootloader mods

Hardware mods

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags