MikroTik RB912R-2nD (LtAP mini)

RouterBOOT booter 6.46.4 RB912R-2nD CPU frequency: 650 MHz Memory speed: 300 MHz Memory size: 64 MiB Storage size: 16 MiB Press any key within 2 seconds to enter setup.. loading kernel... OK setting up elf image... OK jumping to kernel code Starting... MikroTik 6.46.4 (stable) MikroTik Login:

RouterBOOT booter 6.46.4 RB912R-2nD CPU frequency: 650 MHz Memory speed: 300 MHz Memory size: 64 MiB Storage size: 16 MiB Press any key within 9 seconds to enter setup......... writing settings to flash... OK trying bootp protocol................... OK Got IP address: 192.168.88.158 resolved mac address D4:6E:0E:0D:FA:EA Gateway: 192.168.88.2 transfer started ............................. transfer ok, time=3.25s setting up elf image... OK jumping to kernel code OpenWrt kernel loader for AR7XXX/AR9XXX Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80060000... [ 0.000000] Linux version 4.14.125 (buildbot@602ce18687ab) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10243-4d11c4c378)) #0 Mon Jun 17 04:53:07 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a8 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,115200 no-buzzer no-nand parts=1 boot_part_size=16777216 gpio=0 HZ=325000000 mem=64M kmac=B8:69:F4:0F:DA:D9 board=ltap-hb board=ltap-hb vd [ 0.000000] MIPS: no machine found for id 'ltap-hb', supported machines: [ 0.000000] id name [ 0.000000] Generic Generic AR71XX/AR724X/AR913X based board [ 0.000000] 2011G (null) [ 0.000000] 2011r5 (null) [ 0.000000] 2011US (null) [ 0.000000] 2011L (null) [ 0.000000] 493G MikroTik RouterBOARD 493G [ 0.000000] 493 MikroTik RouterBOARD 493/AH [ 0.000000] 450G MikroTik RouterBOARD 450G [ 0.000000] 450 MikroTik RouterBOARD 450 [ 0.000000] 435G MikroTik RouterBOARD 435G [ 0.000000] 433U MikroTik RouterBOARD 433UAH [ 0.000000] 433 MikroTik RouterBOARD 433/AH [ 0.000000] 411U MikroTik RouterBOARD 411U [ 0.000000] 411 MikroTik RouterBOARD 411/A/AH [ 0.000000] 751g MikroTik RouterBOARD 751G [ 0.000000] 751 MikroTik RouterBOARD 751 [ 0.000000] 750Gr3 MikroTik RouterBOARD 750GL [ 0.000000] 750i MikroTik RouterBOARD 750 [ 0.000000] 711Gr100 (null) [ 0.000000] 922gs (null) [ 0.000000] 951HnD MikroTik RouterBOARD 951Ui-2HnD [ 0.000000] 951G MikroTik RouterBOARD 951G-2HnD [ 0.000000] 931 (null) [ 0.000000] wapg-sc (null) [ 0.000000] map2-hb (null) [ 0.000000] cap-hb (null) [ 0.000000] wap-lte (null) [ 0.000000] wap-hb (null) [ 0.000000] lhg (null) [ 0.000000] 750-hb (null) [ 0.000000] 962 (null) [ 0.000000] 952-hb (null) [ 0.000000] 911L (null) [ 0.000000] H951L (null) [ 0.000000] map-hb (null) [ 0.000000] sxt5n MikroTik RouterBOARD SXT Lite5 [ 0.000000] sxt2n MikroTik RouterBOARD SXT Lite2 [ 0.000000] MIPS: no machine found for id 'ltap-hb', supported machines: [ 0.000000] id name [ 0.000000] Generic Generic AR71XX/AR724X/AR913X based board [ 0.000000] 2011G (null) [ 0.000000] 2011r5 (null) [ 0.000000] 2011US (null) [ 0.000000] 2011L (null) [ 0.000000] 493G MikroTik RouterBOARD 493G [ 0.000000] 493 MikroTik RouterBOARD 493/AH [ 0.000000] 450G MikroTik RouterBOARD 450G [ 0.000000] 450 MikroTik RouterBOARD 450 [ 0.000000] 435G MikroTik RouterBOARD 435G [ 0.000000] 433U MikroTik RouterBOARD 433UAH [ 0.000000] 433 MikroTik RouterBOARD 433/AH [ 0.000000] 411U MikroTik RouterBOARD 411U [ 0.000000] 411 MikroTik RouterBOARD 411/A/AH [ 0.000000] 751g MikroTik RouterBOARD 751G [ 0.000000] 751 MikroTik RouterBOARD 751 [ 0.000000] 750Gr3 MikroTik RouterBOARD 750GL [ 0.000000] 750i MikroTik RouterBOARD 750 [ 0.000000] 711Gr100 (null) [ 0.000000] 922gs (null) [ 0.000000] 951HnD MikroTik RouterBOARD 951Ui-2HnD [ 0.000000] 951G MikroTik RouterBOARD 951G-2HnD [ 0.000000] 931 (null) [ 0.000000] wapg-sc (null) [ 0.000000] map2-hb (null) [ 0.000000] cap-hb (null) [ 0.000000] wap-lte (null) [ 0.000000] wap-hb (null) [ 0.000000] lhg (null) [ 0.000000] 750-hb (null) [ 0.000000] 962 (null) [ 0.000000] 952-hb (null) [ 0.000000] 911L (null) [ 0.000000] H951L (null) [ 0.000000] map-hb (null) [ 0.000000] sxt5n MikroTik RouterBOARD SXT Lite5 [ 0.000000] sxt2n MikroTik RouterBOARD SXT Lite2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 56500K/65536K available (4400K kernel code, 191K rwdata, 968K rodata, 2176K init, 218K bss, 9036K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] Clocks: CPU:650.000MHz, DDR:600.000MHz, AHB:300.000MHz, Ref:25.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns [ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns [ 0.008865] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688) [ 0.075995] pid_max: default: 32768 minimum: 301 [ 0.081503] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.089016] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100057] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.111274] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.119506] NET: Registered protocol family 16 [ 0.126196] MIPS: machine is Generic AR71XX/AR724X/AR913X based board [ 0.154999] clocksource: Switched to clocksource MIPS [ 0.161811] NET: Registered protocol family 2 [ 0.167691] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.175674] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.182898] TCP: Hash tables configured (established 1024 bind 1024) [ 0.190269] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.196954] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.204348] NET: Registered protocol family 1 [ 2.575015] random: fast init done [ 3.261615] Crashlog allocated RAM at address 0x3f00000 [ 3.269085] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 3.282377] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 3.289053] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 3.436743] io scheduler noop registered [ 3.441193] io scheduler deadline registered (default) [ 3.447469] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 3.456738] console [ttyS0] disabled [ 3.480936] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A [ 3.490735] console [ttyS0] enabled [ 3.490735] console [ttyS0] enabled [ 3.498292] bootconsole [early0] disabled [ 3.498292] bootconsole [early0] disabled [ 3.508691] libphy: Fixed MDIO Bus: probed [ 3.515073] NET: Registered protocol family 10 [ 3.532783] Segment Routing with IPv6 [ 3.536735] NET: Registered protocol family 17 [ 3.541394] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.554793] 8021q: 802.1Q VLAN Support v1.8 [ 3.559280] rb: no calibration data found [ 3.579207] Freeing unused kernel memory: 2176K [ 3.583893] This architecture does not have kernel memory protection. [ 3.605528] init: Console is alive [ 3.609298] init: - watchdog - [ 3.633811] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.642902] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.660902] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 6.969498] procd: - early - [ 6.972592] procd: - watchdog - [ 7.525898] procd: - watchdog - [ 7.529457] procd: - ubus - [ 7.539397] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.582928] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.589985] random: ubusd: uninitialized urandom read (4 bytes read) [ 7.597496] procd: - init - Please press Enter to activate this console. [ 8.055568] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.079854] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 8.102818] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7 [ 8.110707] Backport generated by backports.git v4.19.32-1-0-g1c4f7569 [ 8.137521] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.144716] urngd: v1.0.0 started. [ 8.163523] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) [ 8.279964] xt_time: kernel timezone is -0000 [ 8.400620] PPP generic driver version 2.4.2 [ 8.416131] NET: Registered protocol family 24 [ 8.500818] kmodloader: done loading kernel modules from /etc/modules.d/* [ 8.525629] random: crng init done [ 8.529160] random: 7 urandom warning(s) missed due to ratelimiting BusyBox v1.31.0 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r10243-4d11c4c378 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#