Sagem F@ST2704 V2

HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LSYN USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 5.38.6 for BCM96328 (32bit,SP,BE) Build Date: Thu Feb 9 17:58:50 CST 2012 (cookiechen@SZ01007.DONGGUAN.CN) Copyright (C) 2005-2010 SAGEM Corporation. HS Serial flash device: name S25FL064, id 0x0116 size 8192KB Total Flash size: 8192K with 128 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-5) : F@ST2704V2 Number of MAC Addresses (1-32) : 11 Base MAC Address : 2c:e4:XX:XX:XX:XX PSI Size (1-64) KBytes : 40 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80010000 LZMA: Prossible old LZMA format, trying to decompress.. Decompression OK! Entry at 0x80010000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80010000 [ 0.000000] Linux version 3.10.49 (openwrt@gb-13) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41842) ) #1 Sun Jul 27 11:39:50 UTC 2014 [ 0.000000] Detected Broadcom 0x6328 CPU revision b0 [ 0.000000] CPU frequency is 320 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 32 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 53.46.51-56.46-54 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350) [ 0.000000] board: board name: F@ST2704V2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 61112k/65536k available (2503k kernel code, 4424k reserved, 723k data, 292k init, 0k highmem) [ 0.000000] NR_IRQS:256 [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.288000] registering PCI controller with io_map_base unset [ 0.300000] bio: create slab <bio-0> at 0 [ 0.308000] PCI host bridge to bus 0000:00 [ 0.312000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff] [ 0.316000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.320000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.324000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.328000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff] [ 0.332000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit] [ 0.336000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.340000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff] [ 0.344000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.348000] Switching to clocksource MIPS [ 0.356000] NET: Registered protocol family 2 [ 0.364000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.368000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.376000] TCP: Hash tables configured (established 512 bind 512) [ 0.384000] TCP: reno registered [ 0.388000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.392000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] NET: Registered protocol family 1 [ 0.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.416000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.424000] msgmni has been set to 119 [ 0.428000] io scheduler noop registered [ 0.432000] io scheduler deadline registered (default) [ 0.440000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart [ 0.448000] console [ttyS0] enabled, bootconsole disabled [ 0.448000] console [ttyS0] enabled, bootconsole disabled [ 0.468000] m25p80 spi1.0: found s25sl064p, expected m25p80 [ 0.472000] m25p80 spi1.0: s25sl064p (8192 Kbytes) [ 0.480000] bcm63xxpart: CFE boot tag found with version 6 and board type F@ST2704V2 [ 0.488000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.492000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11ff00 [ 0.500000] bcm63xxpart: Partition 2 is rootfs offset 130000 and length 6c0000 [ 0.508000] bcm63xxpart: Partition 3 is nvram offset 7f0000 and length 10000 [ 0.516000] bcm63xxpart: Partition 4 is linux offset 10000 and length 7e0000 [ 0.524000] bcm63xxpart: Spare partition is offset 300004 and length 4efffc [ 0.528000] 5 bcm63xxpart partitions found on MTD device spi1.0 [ 0.536000] Creating 5 MTD partitions on "spi1.0": [ 0.540000] 0x000000000000-0x000000010000 : "CFE" [ 0.548000] 0x000000010100-0x000000130000 : "kernel" [ 0.552000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.568000] 0x000000130000-0x0000007f0000 : "rootfs" [ 0.576000] mtd: device 2 (rootfs) set to be root filesystem [ 0.584000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000 [ 0.592000] 0x000000300000-0x0000007f0000 : "rootfs_data" [ 0.600000] 0x0000007f0000-0x000000800000 : "nvram" [ 0.608000] 0x000000010000-0x0000007f0000 : "linux" [ 0.656000] b53_common: found switch: BCM63xx, rev 0 [ 0.664000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.676000] TCP: cubic registered [ 0.676000] NET: Registered protocol family 17 [ 0.684000] Bridge firewalling registered [ 0.688000] 8021q: 802.1Q VLAN Support v1.8 [ 0.704000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.716000] Freeing unused kernel memory: 292K (80337000 - 80380000) procd: Console is alive procd: - watchdog - [ 4.172000] Button Hotplug driver version 0.4.1 [ 4.184000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0 procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready jffs2 is ready [ 8.676000] jffs2: notice: (215) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found. [ 9.868000] usbcore: registered new interface driver usbfs [ 9.872000] usbcore: registered new interface driver hub [ 9.880000] usbcore: registered new device driver usb [ 10.132000] SCSI subsystem initialized [ 10.152000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.160000] ehci-platform: EHCI generic platform driver [ 10.272000] ehci-platform ehci-platform: EHCI Host Controller [ 10.276000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 10.284000] ehci-platform ehci-platform: irq 50, io mem 0xb0002500 [ 10.304000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored [ 10.312000] hub 1-0:1.0: USB hub found [ 10.316000] hub 1-0:1.0: 1 port detected [ 10.328000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.336000] ohci-platform ohci-platform: Generic Platform OHCI Controller [ 10.340000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 [ 10.348000] ohci-platform ohci-platform: irq 49, io mem 0xb0002600 [ 10.416000] hub 2-0:1.0: USB hub found [ 10.420000] hub 2-0:1.0: 1 port detected [ 10.432000] uhci_hcd: USB Universal Host Controller Interface driver [ 10.452000] usbcore: registered new interface driver usb-storage kmod: ran 24 iterations block: extroot: no root or overlay mount defined switching to overlay procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 13.720000] NET: Registered protocol family 10 [ 13.736000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 13.744000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A [ 13.752000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 13.760000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 13.768000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 13.860000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM [ 13.868000] bcma: bus0: Using fallback SPROM failed (err -2) [ 13.872000] bcma: bus0: No SPROM available [ 13.888000] bcma: bus0: Bus registered [ 13.908000] nf_conntrack version 0.5.0 (959 buckets, 3836 max) [ 13.928000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 13.952000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 13.960000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 13.972000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.052000] xt_time: kernel timezone is -0000 [ 14.124000] cfg80211: Calling CRDA to update world regulatory domain [ 14.136000] cfg80211: World regulatory domain updated: [ 14.140000] cfg80211: DFS Master region: unset [ 14.144000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 14.156000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 14.164000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 14.172000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 14.180000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A) [ 14.188000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 14.196000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 14.204000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 14.212000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 14.332000] PPP generic driver version 2.4.2 [ 14.340000] NET: Registered protocol family 24 [ 14.400000] b43-phy0: Broadcom 43225 WLAN found (core revision 23) [ 14.404000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 14.412000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0 [ 14.432000] Broadcom 43xx driver loaded [ Features: PNL ] procd: - init complete - [ 25.216000] device eth0.1 entered promiscuous mode [ 25.224000] device eth0 entered promiscuous mode [ 25.232000] br-lan: port 1(eth0.1) entered forwarding state [ 25.236000] br-lan: port 1(eth0.1) entered forwarding state [ 27.240000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.22.1 (2014-07-27 11:27:39 UTC) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r41842) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/#